CBCALHN-EAC Full en Us Letter

snhy.
com/CBCALHN-EAC
MODEL 3:1 pilot ratio, standard capacity counterbalance valve

CBCALHN-EAC CAPACITY: 15 gpm | CAVITY: T-11A
CARTRIDGE CONFIGURATION
L Control Standard Screw
Adjustment Counterbalance valves with pilot assist are meant to control an overrunning load. The check valve allows free flow from
the directional valve (port 2) to the load (port 1) while a direct-acting, pilot-assisted relief valve controls flow from port 1 to
H Functional Setting 1000 - 4000 psi w/25 port 2. Pilot assist at port 3 lowers the effective setting of the relief valve at a rate determined by the pilot ratio.
Range psi Check (70 - 280
bar w/ 1,7 bar Check), Other names for this valve include motion control valve and over-center valve.
3000 psi (210 bar)
Standard Setting CARTRIDGE TECHNICAL DATA
N Seal Material Buna-N Cavity T-11A
(none) Material/Coating Series 1
Capacity 15 gpm
MANIFOLD CONFIGURATION
Pilot Ratio 3:1
(none) Modifier 6061-T651 Aluminum,
Buna-N Maximum Recommended Load Pressure at Maximum Setting 3075 psi
Maximum Setting 4000 psi
PORT HEADINGS AND SIZES Factory Pressure Settings Established at 2 in³/min.
Modifiers Ports Maximum Valve Leakage at Reseat 5 drops/min.
EAC, /10, Ports 1 & 2: 1/2" NPTF; Port 3: 3/8" Adjustment - No. of CCW Turns from Min. to Max. Setting 3.75
/11 NPTF;
Operating Characteristic Standard
Reseat >85% of setting

NOTES
Important: Carefully consider the maximum system Valve Hex Size 7/8 in.
pressure. The pressure rating of the manifold is
Valve Installation Torque 30 - 35 lbf ft
dependent on the manifold material, with the port
type/size a secondary consideration. Manifolds Adjustment Screw Internal Hex Size 5/32 in.
constructed of aluminum are not rated for pressures
higher than 3000 psi (210 bar), regardless of the port Locknut Hex Size 9/16 in.
type/size specified.
Locknut Torque 80 - 90 lbf in.
Seal kit - Cartridge Buna: 990-011-007
Seal kit - Cartridge EPDM: 990-011-014
Seal kit - Cartridge Polyurethane: 990-011-002

Seal kit - Cartridge Polyurethane: 990-011-002
Seal kit - Cartridge Viton: 990-011-006
Model Weight 0.35 lb.
MANIFOLD TECHNICAL DATA

Body Type Line mount
Interface None
Body Features Ninety degree with high capacity port 3
Mounting Hole Diameter .34 in.
Mounting Hole Depth Through
Mounting Hole Quantity 2
Open Cavities 1
Cavity T-11A
Port Size 1/2" NPTF
Model Weight 0.71 lb.
CARTRIDGE TECHNICAL FEATURES

Counterbalance valves should be set at least 1.3 times the maximum load induced pressure.
Turn adjustment clockwise to decrease setting and release load.

Full clockwise setting is less than 200 psi (14 bar).
Backpressure at port 2 adds to the effective relief setting at a ratio of 1 plus the pilot ratio times the backpressure.
Reseat exceeds 85% of set pressure when the valve is standard set. Settings lower than the standard set pressure may result in lower reseat percentages.
This valve does not have positive seals on the pilot section and will pass up to 3 in³/min.@1000 psi (45 ml/min.@70 bar ) between port 2 and port 3. This is a consideration in
master-slave circuits and in the leak testing of valve-cylinder assemblies.
Cartridges configured with EPDM seals are for use in systems with phosphate ester fluids. Exposure to petroleum based fluids, greases and lubricants will damage the seals.
Sun counterbalance cartridges can be installed directly into a cavity machined in an actuator housing for added protection and improved stiffness in the circuit.
Two check valve cracking pressures are available. Use the 25 psi (1,7 bar) check unless actuator cavitation is a concern.
All 3-port counterbalance, load control, and pilot-to-open check cartridges are physically interchangeable (i.e. same flow path, same cavity for a given frame size).
Corrosion-resistant cartridge valves are intended for use in corrosive environments and are identified by the model code suffix /AP for external stainless steel components, or /LH
for external zinc-nickel plated components. See the CONFIGURATION section for all options. For further details, please see the Materials of Construction page located under
TECH RESOURCES.
Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining
variations.
ASSEMBLY FACES
FACE GRID
1 2 3 4
5 6 7 8
9 10 11 12
Face 2
Face 5
Face 6
Face 7
Face 8
Face 10
Copyright © 2002-2023 Sun Hydraulics. All rights reserved.

CBCALHN-EAC Full en Us Letter

Uploaded by

Copyright:

Available Formats

CBCALHN-EAC Full en Us Letter

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CBCALHN-EAC Full en Us Letter

Uploaded by

Copyright:

Available Formats

snhy.

MODEL 3:1 pilot ratio, standard capacity counterbalance valve

Maximum Setting 4000 psi

PORT HEADINGS AND SIZES Factory Pressure Settings Established at 2 in³/min.

Modifiers Ports Maximum Valve Leakage at Reseat 5 drops/min.

Reseat >85% of setting

Seal kit - Cartridge Buna: 990-011-007

Seal kit - Cartridge EPDM: 990-011-014

Seal kit - Cartridge Polyurethane: 990-011-002

Seal kit - Cartridge Viton: 990-011-006

Model Weight 0.35 lb.

MANIFOLD TECHNICAL DATA

Body Features Ninety degree with high capacity port 3

Mounting Hole Diameter .34 in.

Mounting Hole Depth Through

Mounting Hole Quantity 2

Port Size 1/2" NPTF

Model Weight 0.71 lb.

CARTRIDGE TECHNICAL FEATURES

Turn adjustment clockwise to decrease setting and release load.

You might also like