Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Owner'S Manual

Download as pdf or txt
Download as pdf or txt
You are on page 1of 132

OWNER’S MANUAL Basic Photography

This manual will show you how to use your FUJIFILM DIGITAL CAMERA
FinePix S1 Pro correctly.
Please follow the instructions carefully. Setup

Advanced Photography

Advanced Photography
(Playback)

Preference
BB11378-200 (1)
Downloaded from ManualsCamera.com Manuals
Warning

To prevent fire or shock hazard, do not expose the unit to rain or


moisture.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.


DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The graphical symbols are located on the bottom


of the case.

This symbol is intended to alert the user to the presence of uninsulated


“dangerous voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature accompanying the
appliance.

For customers in the U.S.A.


FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:(1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

CAUTION
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly approved in this
manual could void your warranty.
Downloaded from ManualsCamera.com Manuals
2
For customers in Canada
CAUTION
This Class B digital apparatus complies with Canadian ICES-003.

EC Declaration of Conformity
We
Name : Fuji Photo Film (Europe) G.m.b.H.
Address : Heesenstrasse 31
40549 Dusseldorf, Germany

declare that the product


Product Name : FUJIFILM DIGITAL CAMERA FinePix S1 Pro
Manufacture’s Name : Fuji Photo Film Co., Ltd.
Manufacture’s Address : 26-30, Nishiazabu 2-chome, Minato-ku,
Tokyo 106-8620, Japan

is in conformity with the following Standards


Safety : EN60065
EMC : EN55022 : 1998 Class B
EN55024 : 1998
EN61000-3-2 : 1995 + A1:1998 + A2:1998

following the provision of the EMC Directive (89/336/EEC, 92/31/EEC and 93/68/EEC) and
Low Voltage Directive (73/23/EEC).

Dusseldorf,Germany June 1,2000


Place Date Signature/Managing Director

Bij dit produkt zijn batterijen geleverd. Wanneer deze leeg zijn, moet u ze niet
weggooien maar inleveren als KCA

Please read the Safety Notes (☞P.129) and make sure you
understand them before using the camera.
Downloaded from ManualsCamera.com Manuals
3
Contents
Warning .............................................................................................................. 2
Contents............................................................................................................. 4
Preface ............................................................................................................... 8
Camera Features and Accessories.................................................................. 9
Features ..................................................................................................................9
Accessories ............................................................................................................ 9
Nomenclature .................................................................................................. 10
Rear Display Panel Screens................................................................................. 13
Top Display Panel ................................................................................................ 14
Viewfinder Display ................................................................................................ 15

1 Basic Photography
1 Attaching the Shoulder Strap...................................................................... 16
Using the Shoulder Strap ..................................................................................... 16
2 Loading the Camera Batteries .................................................................... 17
Loading the Lithium Batteries ............................................................................... 17
Loading the Button Cell ........................................................................................ 17
Loading the AA Batteries ...................................................................................... 18
Using the AC Power Adapter AC-5VH (optional) ................................................. 19
3 Mounting the Camera Lens ......................................................................... 20
4 Switching the Camera On and Off .............................................................. 22
5 Setting the Date and Time ........................................................................... 23
6 Loading Media .............................................................................................. 24
7 Removing Media........................................................................................... 25
8 Exposure Modes on the FinePix S1 Pro..................................................... 26
9 Setting the Exposure Mode Dial ................................................................. 27
10 Holding the Camera and Focusing ........................................................... 28
11 Releasing the Shutter ................................................................................ 30
12 Playing Back Photographed Images ........................................................ 31
To View Images (Playback) .................................................................................. 31
Playback Zoom ..................................................................................................... 32
Multi-frame Playback ............................................................................................ 33
Erasing Single Recorded Images ......................................................................... 35
Viewing Images on a TV....................................................................................... 36
Background: A Brief Guide Focusing and Exposure .................................. 37

2 Setup
Setup Functions .............................................................................................. 38
Rear Display Panel .............................................................................................. 40
Setting the White Balance .............................................................................. 40
Setting the Sensitivity..................................................................................... 42
Downloaded from ManualsCamera.com Manuals
4
Setting the Image Quality ............................................................................... 43
Setting the Image Size (Number of Pixels) ................................................... 44
Setting the Color ............................................................................................. 45
Setting the Tone .............................................................................................. 46
Setting the Sharpness .................................................................................... 47
Setting Multi-exposure.................................................................................... 48
SET-UP Menu Part 1 ............................................................................................ 49
Preview............................................................................................................. 49
Specifying a Custom WB Setting....................................................................50
Hi MODE/MEDIA .............................................................................................. 51
Hi MODE .............................................................................................................. 51
MEDIA .................................................................................................................. 51
SELF TIMER/AUTO POWER OFF ................................................................... 52
SELF TIMER ........................................................................................................ 52
AUTO POWER OFF ............................................................................................. 52
SET-UP Menu Part 2 ............................................................................................ 53
FRAME No. ...................................................................................................... 53
PC MODE/BEEP............................................................................................... 54
PC MODE ............................................................................................................. 54
BEEP .................................................................................................................... 54
LANGUAGE/RESET......................................................................................... 55
LANGUAGE.......................................................................................................... 55
RESET.................................................................................................................. 55
Camera Reset .................................................................................................. 56
Camera Reset ...................................................................................................... 56

3 Advanced Photography
Focusing Modes .............................................................................................. 57
When the Focusing Mode is Set to AF (auto focus) ............................................. 57
Auxiliary AF Light.................................................................................................. 57
When M (manual focus) is Selected ..................................................................... 58
Focus Lock Photography ............................................................................... 59 1
Shooting Using Exposure Modes ...................................................................60
z : AUTO .......................................................................................................... 60 2
P : Programmed Auto ........................................................................................61
S : Shutter-priority Auto .................................................................................... 62
A : Aperture-priority Auto .................................................................................. 63 3
M : Manual......................................................................................................... 64
Shooting Using 5-Vari Programs ................................................................... 66 4
5-Vari Programs ................................................................................................... 66
Taking Pictures Using 5-Vari Programs ............................................................... 66
5-Vari Program Types and Features .................................................................... 67 5
Downloaded from ManualsCamera.com Manuals
5
Contents - continued

x : Portrait mode ...............................................................................................67


c : Landscape mode......................................................................................... 67
v : Close-up mode ............................................................................................ 67
b : Sport mode (continuous shooting) .............................................................. 68
n : Night scene mode ....................................................................................... 68
Metering Modes ............................................................................................... 69
Multi-pattern Metering and 3D 6-zone Multi-pattern Metering .............................. 69
Center-weighted Metering .................................................................................... 69
AE Lock Photography..................................................................................... 70
Exposure Compensation ................................................................................ 71
Self-timer Photography................................................................................... 72
Diopter Adjustment Function/Eyepiece Cap ................................................ 73
Flash Photography.......................................................................................... 74
Built-in Flash and TTL-BL Flash Control .............................................................. 74
Flash Control Range (Effective Flash range) ....................................................... 74
Synchro Mode Types and Features ..................................................................... 75
K : Red-eye reduction mode ............................................................................. 75
L : Slow synchro mode ..................................................................................... 75
Taking Pictures Using the Built-in Flash ............................................................... 76
Flash Intensity ...................................................................................................... 77
Lenses that Can Be Used with the Built-in Flash ................................................. 77
Nikon Flash Units that Can Be Used .................................................................... 78
Notes on Using Nikon Flash Units ........................................................................ 79
Combining Modes ........................................................................................... 80
Shooting and Recording Previews ................................................................ 81
Standard Chart Display................................................................................... 82
Histogram Display........................................................................................... 83
Multi-exposure................................................................................................. 84

4 Advanced Photography (Playback)


Playback Functions......................................................................................... 85
Erase/Format ................................................................................................... 86
Erase All/Format ................................................................................................... 86
Protection Settings ......................................................................................... 88
Protecting and Unprotecting Individual Image ...................................................... 88
Protecting and Unprotecting All Images ............................................................... 89
DPOF Settings ................................................................................................. 91
DPOF.................................................................................................................... 91
Setting or Cancelling Date/Time Imprinting .......................................................... 92
Specifying DPOF Settings for Single Frame ........................................................ 93
Checking and Cancelling DPOF Settings for Single Frame
(REVIEW/CANCEL) .......................................................................................... 95
Setting DPOF Settings for All the Images (SET ALL)........................................... 97
Cancelling
Downloaded DPOF
from Settings for All Frames (CANCEL
ManualsCamera.com Manuals ALL) ................................... 99
6
Auto Play (Automatic Playback) .................................................................. 101
Auto Play Settings .............................................................................................. 101
Adjusting the Color LCD Monitor Brightness............................................. 103

5 Reference
System Expansion Options.......................................................................... 105
Lenses that Can Be Used with this Camera ............................................... 106
Types of Nikkor Lenses with a Built-in CPU and Other Lenses that Can Be Used.. 107
Optional Accessories Guide ........................................................................ 108
Explanation of Terms.................................................................................... 110
Using the USB Cable and the Software Included....................................... 111
Notes on Using the FinePix S1 Pro ............................................................. 113
Cleaning the CCD .......................................................................................... 114
Determining Whether Cleaning is Required ....................................................... 115
Cleaning the CCD............................................................................................... 116
Power Supply Notes...................................................................................... 117
Batteries that Can Be Used .................................................................................117
Notes on Handling the Batteries ......................................................................... 117
Notes on Using the AC Power Adapter (AC-5VH) (sold separately) .................. 118
Notes on Media.............................................................................................. 119
Warning Displays .......................................................................................... 121
Troubleshooting ............................................................................................ 124
Specifications ................................................................................................ 126
Standard Number of Available Shots (Recorded Images)...................................128
Compatible Media............................................................................................... 128
Batteries Uses and Symptoms When Batteries are Depleted ............................ 128
Safety Notes................................................................................................... 129

1
2
3
4
5
Downloaded from ManualsCamera.com Manuals
7
Preface
■ Preparatory Trial Shots
When you are taking particularly important photographs (at a wedding or on holiday, for
example), always take a trial photograph first to check that the camera is functioning normally.
* Fuji Photo Film Co., Ltd. accepts no liability for any incidental losses (including any costs
incurred in the course of the photography and any loss of income obtained from the
photography) incurred as a result of any fault in this product.
■ Notes on Copyright
Images recorded using your digital camera cannot be used in ways that infringe copyright laws
without the consent of the owner, unless intended only for personal pleasure. Note also that
some restrictions apply to the photographing of stage performances, entertainments and
exhibits, even when intended purely for personal use. Users are also asked to note that the
transfer of memory cards (SmartMedia or microdrives) containing images or data protected
under copyright laws is only permissible within the restrictions imposed by those copyright
laws.
■ Liquid Crystal
If the LCD panel is damaged, take particular care with the liquid crystal contained in the panel.
If any of the following situations arise, take the urgent action indicated.
● If liquid crystal comes in contact with your skin
Wipe the area with a cloth and then wash thoroughly with running water and soap.
● If liquid crystal gets into your eye
Flush the affected eye with clean water for at least 15 minutes and then seek medical
assistance.
● If liquid crystal is swallowed
Flush your mouth thoroughly with water. Drink large quantities of water and induce vomiting.
Then seek medical assistance.
■ Notes on Electrical Interference
If the camera is needed be used in hospitals or aircrafts, please note that this camera may
cause interference to other equipment in the hospital or aircraft.
For details, please check with the applicable regulations in that place.
■ Handling Your Digital Camera
This camera contains precision electronic components. To ensure that images are recorded
correctly, do not subject the camera to impacts or shocks while image data is being recorded.
■ Trademark Information
● iMac and Macintosh are registered trademarks of Apple Computer, Inc.
● Windows is a trademark of the Microsoft Corporation of the U.S. registered in the USA and
other countries.
Windows is an abbreviated term referring to the Microsoft Windows Operating System.
● SmartMedia is a trademark of Toshiba Corporation.
● All other company or product names used in this document are trademarks or registered
trademarks of their respective holders.
■ Explanation of Color Television System
NTSC: National Television System Committee, color television telecasting specifications
adopted mainly in the U.S.A., Canada and Japan.
PAL: Phase Alternation by Line, a color television system adopted mainly by European
countries and China.

Downloaded from ManualsCamera.com Manuals


8
Camera Features and Accessories

Features
• The newly developed large-size 3.4 million “Super CCD” built into the FinePix S1 Pro provides ultra-
high resolution of 6.13 million output, high sensitivity, a wide dynamic range and an excellent signal-
to-noise ratio.
• Quick, responsive operation with only 0.7 seconds between shots (6.13-million output pixels)
• 5-vari programs and an AUTO photography mode that make it easy to select the right camera
settings for your subject
• Exposure programs and manual photography modes let you fine tune your photography settings
• Built-in flash and support for external flash units
• Dot-matrix LCD panel (backlit) lets you to check your camera settings as you shoot
• Equipped with 2 different recording media slots (slot 1: SmartMedia, slot 2: CF type II)
• Select any of 3 image recording resolutions as needed (6.13 million, 3.54 million or 1.38 million
recorded pixels)
• Histogram display function lets you check the image exposure right after you shoot
• Allows you to set the ISO sensitivity, tint, tone and sharpness individually just as if you were selecting
the film
• 2-inch 200,000-pixel low-temperature polysilicon TFT LCD monitor
• Color and grayscale screen display function for checking colors and highlights/shadows
• USB connection lets you take pictures from your PC and transfer image data quickly and easily
(supplied accessory)
• Supports DPOF (Digital Print Order Format) for simple print ordering
• Conforms to the Design rule for Camera File system.

Accessories
● SmartMedia (1) ● Video Cable (approx. 1.5 m (4.9ft.), mini-
(16MB, 3.3V) plug (3.5 mm-dia.) to pin-plug cable) (1)
Supplied with:
• Anti-static case (1)
• Index labels (1 set)

● Camera Body Cap (1)

● AA-size Alkaline Batteries (4)


● Battery Adapter (1)

● Lithium batteries CR123A (2)


● Eyepiece Cap (1)

● Button Cell Lithium Battery CR2025 (1)

● CD-ROM (1)
● USB Cable (1)
● Shoulder Strap (1) ● Manuals
• Owner’s Manual (this document) (1)
• Quick Start Guide (1)
• Quick Start Guide for Camera Shooting Software (1)
Downloaded from ManualsCamera.com Manuals
9
Nomenclature

Auxiliary AF light (☞ P.57)


Self-timer lamp (☞ P.72)
Top display panel (☞ P.14) Red-eye reduction lamp (☞ P.75)
Exposure compensation
button (☞ P.71) Accessory shoe (☞ P.78)

Aperture button (☞ P.64) Built-in flash (☞ P.74)

Lens detaching
button (☞ P.21)

Synchro mode
button (☞ P.76)

Focus mode
Strap mount selecter switch
(☞ P.16) (☞ P.27, 57)

VIDEO OUT socket (☞ P.36)

Shutter button (☞ P.30) Digital (USB) socket (☞ P.111)

Power switch (☞ P.22) DC IN 5V socket (☞ P.19)

Downloaded from ManualsCamera.com Manuals


10
Self-timer button (☞ P.72) Viewfinder window (☞ P.73)

Diopter adjustment
knob (☞ P.73)

Flash lock release button


(☞ P.76) AE lock button (☞ P.70)

Strap mount
(☞ P.16)

AA battery compartment Command dial


cover release catch (☞ P.18) (☞ P.61)

Eyepiece surround
Exposure mode dial (☞ P.60) (☞ P.73)

Downloaded from ManualsCamera.com Manuals


11
Nomenclature - continued

Function button [4] CANCEL button

Function button [3]


4-driection button
Function button [2]

Function button [1] MENU/EXE button (☞ P.33)

Button cell holder


(☞ P.17)

Rear display
panel (☞ P.13)

Lithium battery
compartment cover
(☞ P.17)
FUNC button (☞ P.40)

PLAY button (☞ P.31) Slot cover (☞ P.24)

Color LCD monitor Tripod mount

Downloaded from ManualsCamera.com Manuals


12
Rear Display Panel Screens
• Display during photography
AA-size battery icon Media icon
(☞P.22) (for SmartMedia)

Sensitivity setting display


(☞P.42)

“FUNC” button

Date/time No. of remaining Menu of settings that can


display standard shots be specified from the rear
display panel (☞P.38)

“FUNC” “FUNC”
button button

Menu of settings that can be specified


from the rear display panel (☞P.38)

• Display during playback Photography information (1)

Date/time information
Quality settings

“FUNC” button

Functions that can be accessed from Image size (number


the rear display panel (☞P.85) of pixels) setting

White balance setting

Photography information (2)

Shutter speed, Sensitivity “FUNC”


“FUNC” aperture setting button
button

Color setting Sharpness setting


Downloaded from ManualsCamera.com
Tone setting Manuals
13
Nomenclature - continued

Top Display Panel

Shutter speed display Exposure compensation icon (☞ P.71)


Program shift icon
(☞ P.61) Aperture setting display

Synchro
mode icon
(☞ P.76)

Lithium battery check Exposure compensation


icon (☞ P.22) amount display (☞ P.71)
Self-timer icon (☞ P.72)

☞ Note
Liquid crystal in the display panels and viewfinder display
The LCDs (liquid-crystal displays) used in the display panels and viewfinder
display darken at high temperatures. At low temperatures the display
responses slow down slightly. In either case, the display will return to normal at
room temperature.

Downloaded from ManualsCamera.com Manuals


14
Viewfinder Display

Center-weighted metering area


Focusing frame (☞ P.59) (12 mm-dia.) (☞ P.69)

Focus indicator (☞ P.28) Flash recommended icon/


Ready icon (☞ P.30, 77)
Shutter speed display Exposure compensation
icon (☞ P.71)
Aperture setting display

Exposure indicator (☞ P.65)

Downloaded from ManualsCamera.com Manuals


15
1 Basic
Photography 1 Attaching the Shoulder Strap

■ Use the shoulder strap to ensure that you do not drop the camera
while taking pictures.

1 Pass the end of the shoulder strap through the strap


mount on the camera body.

2 Pass the end of the strap through the fastener A and


loop B as shown in the figure below.

A
B

• Check that the strap is pulled tight after it is attached.

Using the Shoulder Strap

1 Put the shoulder strap over your shoulder.

• To ensure that you do not drop the camera while taking pictures, slip the
strap over your shoulder before you grip the camera body.

Downloaded from ManualsCamera.com Manuals


16
2 Loading the Camera Batteries

■ The FinePix S1 Pro Digital Camera uses 2 lithium batteries (CR123A


type), 1 button cell and 4 AA batteries. It can also be run from an
ordinary power socket using the optional AC power adapter AC-5VH.
(See P.128 for information on using the batteries.)

Loading the Lithium Batteries

1 Switch the camera “OFF”, slide the open/close catch


on the lithium battery compartment cover in the
direction indicated and open the cover.

2 Load the lithium batteries in the direction indicated by


the + and - labels on the battery compartment cover.
Then firmly close the battery compartment cover.

• Loading the batteries in the wrong direction could cause a camera fault.

Loading the Button Cell

1
1 Switch the camera “OFF” and then use a coin to pull
out the button cell holder.

Downloaded from ManualsCamera.com Manuals


17
Loading the Camera Batteries - continued

2 Load the button in the direction indicated by the + and


- labels on the button cell holder. Then firmly close
the holder.

• Loading the button cell in the wrong direction could cause a camera fault.

Loading the AA Batteries


Batteries
• AA-size alkaline batteries (provided), AA-size Ni-Cd batteries or AA-size
nickel metal hydride (Ni-MH) batteries can be used.

1 Switch the camera “OFF”, lift up the AA battery


compartment cover release catch and open the cover
downwards.

2 Load the AA batteries in the direction indicated by the


+ and - labels on the battery compartment cover.
Then firmly close the battery compartment cover.

• Loading the batteries in the wrong direction could cause a camera fault.
• If you switch the camera “ON” without loading AA-size batteries, the
“‹” warning appears on the top display panel and the camera will not
take pictures.

Downloaded from ManualsCamera.com Manuals


18
Using the AC Power Adapter AC-5VH (optional)

1 Open the lithium battery compartment cover as


described in step 1 in “Loading the Lithium Batteries”.
• When the camera is connected to a personal computer or you are
viewing recorded images on a TV so that the camera is switched on for
an extended period, you should use the AC-5VH.
When you use the AC-5VH, you can load the battery adapter (supplied)
instead of the lithium batteries to prevent the lithium batteries being
depleted.
However, bear in mind that you cannot use the built-in flash when you
are using the battery adapter.

2 Insert the battery adapter as shown in the figure and


firmly close the battery compartment cover.

☞ Note
Notes on using the battery adapter
When you use the battery adapter, use the AC-5VH or AA-size Ni-MH batteries.

3 Insert the connection plug for the AC-5VH into the DC IN


5V socket on the camera and plug the AC-5VH into the
power socket.

1
• To remove the battery adapter, grasp • The socket-outlet shall installed
the catch with your fingers and lift the near the equipment and shall
adapter out. be easily accessible.
• The shapes of the AC-5VH,
plug and socket-outlet depends
on the country of use.
• You cannot charge the
batteries by connecting the AC-
5VH.
Downloaded from ManualsCamera.com Manuals
19
3 Mounting the Camera Lens

■ Switch the camera “OFF” to mount the camera lens. Always leave the
aperture ring set to the smallest aperture (the aperture setting with the
highest number).

1 Switch the camera off and mount the camera lens.

• Align the mounting marks on the lens and the camera body and then turn
the lens slowly in the direction of the arrow until it clicks into place. (Do
not press the lens detaching button.)
• If you switch the camera on when there is no lens mounted or when the
lens mounted is not a Nikkor lens with a built-in CPU (☞ P.107), the “°”
warning appears blinking on the top display panel and in the viewfinder
display and the shutter will not release (If the exposure mode is set to
Manual, the shutter will release when the “°” warning is displayed.)
(☞ P.121).
☞ Note
Notes on Changing the Lens
• Take care not to mount the lens when it is at an angle to the camera as this
can damage the lens mount on the camera.
• Always change the lens in an area free of dirt and dust.

2 Set the aperture ring to the smallest aperture and lock


the aperture ring.

• If you switch the camera “ON” when the aperture ring is not set to the
smallest aperture, “‡” appears blinking on the top display panel and in
the viewfinder display and the shutter will not release (☞ P.121).
• Always lock the aperture ring. If the aperture ring slips, the shutter may
not release when you press the shutter button.

Downloaded from ManualsCamera.com Manuals


20
3 To detach the lens from the camera body.

• Hold down the lens detaching button and turn the lens in the direction of
the arrow.

✎ Important
When the camera is stored with the lens detached
While the lens is detached from the
camera, fit the camera body cap provided
onto the camera to protect the inside of the
camera and prevent soiling of the mirror
and viewfinder screen.
(You can also use the Nikon BF-1A Body
Cap.)

Downloaded from ManualsCamera.com Manuals


21
4 Switching the Camera On and Off

1 To switch the camera on or off, set the power switch to


“ON” or “OFF” respectively. When you switch the
camera on, the battery check icon “I” appears.
• Top display panel display

I (lit): Ample charge in the CR123A lithium batteries


O (lit): Charge in the CR123A lithium batteries is low. Have
replacement batteries ready.
O (blinking): Replace the CR123A lithium batteries.
The battery check icon blinks for about 3 seconds and
then the Auto Power Off function switches the camera off.
The battery icon then stops blinking and remains lit.
The viewfinder display switches off and the shutter will
not release.
If this occurs when you are using the battery adapter,
replace the AA-size batteries.

• Rear display panel display

(lit): Ample charge in the AA-size batteries


(lit): Charge in the AA-size batteries is low. Have replacement
batteries ready.
(blinking): Replace the AA-size batteries.
The battery check icon blinks for about 3 seconds and
then the Auto Power Off function switches the camera off.
• If the date and time are not set, the date/time display on the rear display
panel blinks.

☞ Note
Notes on the Batteries
• Do not use depleted batteries.
• If you take pictures or play back images when the battery charge is low, you
may find that you can no longer take pictures or play back images regardless
of which battery check icon is lit. If this occurs, switch the camera “OFF” and
replace the batteries.
Downloaded from ManualsCamera.com Manuals
22
5 Setting the Date and Time

■ Use the procedure below to set the date and time.

1 Press the “MENU/EXE” button. The “SET-UP” menu


appears on the color LCD monitor.

Press “a” or “b ” on the 4-direction button to select


2 “DATE/TIME” and press the”MENU/EXE” button.

Press “a” or “b ” on the 4-direction button to select the


3 desired setting and then press the “d” or “c” button.

• Select “DATE TYPE” to set “MM/DD/YYYY” (month/day/year),


“DD/MM/YYYY” (day/month/year) or “YYYY.MM.DD” (year.month.day) as
the display format for the date.
• You can also set the “YEAR”, “MONTH”, “DAY”, “HOUR” and “MINUTE”.
Press “ c” on the 4-direction button to increase the number and “d ” to 1
decrease the number.
• Default setting
USA/Canada model: MM/DD/YYYY
Europe model: DD/MM/YYYY

4 Press the “MENU/EXE” button.

Press “a” or “b ” on the 4-direction button to select


5 “END” and then press the “MENU/EXE” button.
Downloaded from ManualsCamera.com Manuals
23
6 Loading Media

1 Switch the camera “OFF”, open the slot cover and


insert the media. Load a Microdrive or a CompactFlash
card into the upper slot and a SmartMedia into the
lower slot.

For a SmartMedia
• Insert a SmartMedia with the contact area (gold-colored area) facing
upwards.
• Insert a Microdrive or a CompactFlash card in the correct direction and
push it smoothly all the way into the slot.

2 Close the slot cover.

• If there is a write-protect sticker on the SmartMedia, data cannot be


recorded onto or deleted from the SmartMedia.
• Compatible Media (☞ P.128).
• Back up your data at regular intervals. Fuji Photo Film Co., Ltd. accepts
no liability for any losses incurred as a result of data being erased or
corrupted.

☞ Note
Notes on Taking Pictures
You can release the shutter of the FinePix S1 Pro when there is no media
installed in the camera. In this event, the image appears on the color LCD
monitor but is not recorded. Always check that there is a media card installed in
the camera before taking pictures.

Downloaded from ManualsCamera.com Manuals


24
7 Removing Media

1 Switch the camera “OFF” and open the slot cover.

• If you open the slot cover when the camera is switched on, the “‹”
warning appears on the top display panel. Switch the camera “OFF” first.
• Do not open the slot cover while data is being recorded as this can result
in data loss or corruption.
• If you open the slot cover during a shot taken with a long shutter speed,
the top display panel continues to operate until the picture is taken.

2 Eject the media.

Microdrive eject button

• To remove a SmartMedia, push the SmartMedia in gently. The


SmartMedia then pops out slightly for easy removal.
• To remove a Microdrive or a CompactFlash card, press the eject button
beside the slot.

3 Close the slot cover.


1

Downloaded from ManualsCamera.com Manuals


25
8 Exposure Modes on the FinePix S1 Pro

Symbol Name Features and Typical Uses


Exposure is controlled entirely by the camera. This
z AUTO mode
mode is ideal for snapshots and other situations where
P.60 you need to take the picture quickly to avoid missing the
moment.
The camera controls the exposure but the photographer
P Programmed can also influence the outcome using the program shift
P.61 Auto (☞ P.61) and exposure compensation (☞ P.71)
features.
You set the shutter speed and the camera controls the
S Shutter-priority exposure. This mode lets you set fast shutter speeds to
P.62 Auto freeze fast-moving subjects or slow shutter speeds to
emphasize the subject’s motion.
You set the aperture and the camera controls the
shutter speed. This mode is ideal for shots where you
A Aperture-priority want to control the depth of field (the range of focus in
P.63 Auto front of and behind the subject) for focusing, such as
shots where you want the foreground and background
both in clear focus or shots where you want the
background deliberately out of focus.
This mode lets you set both the shutter speed and the
M Manual exposure. Use this mode when none of the other modes
P.64
give quite the effect you are looking.
This mode uses a shallow depth of field (the range of
x Portrait mode focus in front of and behind the subject) to give portrait
P.67 shots that have a soft, blurred backdrop and a feeling of
depth.
This mode uses a very large depth of field (the range of
c Landscape focus in front of and behind the subject) to give
mode
5-Vari Programs P.66

P.67 landscape shots in which both nearby and distant


scenery is in focus.
This mode uses a relatively shallow depth of field to
v Close-up mode make the subject stand out and give a soft, blurred
P.67
background for beautiful close-up shots.
This mode uses a fast shutter speed to freeze the
b Sport mode
P.68 action, allowing you to take sports shots that capture the
feeling of rapid motion.
This mode uses exposure control specially tailored to
dimly lit subjects to allow you to take pictures in the
n Night Scene evening or at night. (When you take a picture of a
P.68 mode subject against a night scene background, you can use
the flash to capture both your subject and the
background as they appear naturally.)

Downloaded from ManualsCamera.com Manuals


26
9 Setting the Exposure Mode Dial

■ By setting the exposure mode dial to z (AUTO mode), you can leave
the exposure settings to the camera when you take pictures.

1 Switch the camera “ON”.

2 Set the exposure mode dial to “z” (AUTO mode).

• The shutter speed and aperture settings are shown on the top display
panel.

3 Set the focus mode selector switch to “AF” (auto


focus).

• Make sure that the focus mode selector switch clicks when you select the
setting.
• To focus on your subject, hold the shutter button halfway (☞ P.28).

Downloaded from ManualsCamera.com Manuals


27
10 Holding the Camera and Focusing

■ Hold the shutter button halfway to focus the camera. When your
subject is in focus, the focus indicator “●” appears in the viewfinder.

1 Hold the camera correctly.

• Hold your body straight and brace your elbows lightly against your sides.
• Put one foot forward slightly to keep your upper body steady.
• Hold the camera so that your right hand is firmly around the grip and use
your left hand to support the lens.

✎ Important
Camera shake and shutter speed
Camera shake is something to be avoided when taking pictures. As a general
guide when taking pictures, the shutter speed should be faster than [1/focal
length of the lens mounted] seconds. For example, with a 50 mm lens, you
should use a shutter speed faster than 1/50 sec. Use a tripod for slow shutter
speeds.

☞ Note
Notes on Composing Your Shot
As a percentage of the actual image photographed, the image area visible
through the viewfinder of the FinePix S1 Pro (the viewfinder coverage) is about
90% vertically and about 93% horizontally. In other words, the picture actually
taken is slightly larger than the field of view in the viewfinder.

Downloaded from ManualsCamera.com Manuals


28
2 Compose your shot and press the shutter button
halfway to set the focus.

Focusing
frame

• When you position the focusing frame on the object you want to focus on
and press the shutter button halfway, the camera automatically focuses
on the object and one of the following appears in the viewfinder:
Lit The camera has focused on the subject. If the subject is
moving, the camera adjusts the focus so that it follows the
movements of the subject.
Blinking The camera cannot focus on the subject.
If the subject is dark, the auxiliary AF light automatically operates so that
the camera can focus. See P.57 for more information on focusing.
• If the object you want to focus on is outside the focusing frame, use
focus lock to take the picture (☞ P.59).

Downloaded from ManualsCamera.com Manuals


29
11 Releasing the Shutter

■ Check that the focus indicator “●” is lit and then slowly press the
shutter button down fully to release the shutter.

1 Press the shutter button halfway and check the


viewfinder display.

• If the flash recommended icon “j ” is flashing in the viewfinder display,


use the built-in flash (☞ P.74, 76).
• If a warning is displayed on the top display panel or viewfinder display,
refer to P.121 and P.122 for information on how to respond.

2 Check that the focus indicator “●” is lit and then gently
press the shutter button fully.

• The “REC” icon flashes on the rear display panel while the image is
being recorded.

• The shutter does not release during recording when Preview mode is set
to ON.
• If the number of prints display is highlighted, the shutter will not release
even when the focus indicator “●” is lit.
• When there is no media loaded, you can display and review an image
but you can not record it.
Downloaded from ManualsCamera.com Manuals
30
12 Playing Back Photographed Images

■ Use the procedure below to play back images you have shot and
recorded.

To View Images (Playback)


Play back recorded images as follows:

1 Press the “PLAY” button. The recorded image is played


back on the color LCD monitor.

FUNC

PLAY

To view another image, use “c” (scan forwards) or “d”


2 (scan backwards) on the 4-direction button.

1
• Pressing the “PLAY” button again (twice when multi-frame playback is
selected) returns the camera to photography mode.
• Press the shutter button down halfway to return to shooting mode.

Downloaded from ManualsCamera.com Manuals


31
Playing Back Photographed Images - continued

Playback Zoom
Use playback zoom to view details of the image being played back enlarged.

1 Display the recorded image. (See “To View Images


(Playback)”.)
• You cannot use this method in “4-MULTI” or “9-MULTI” display mode.
Switch back to single-frame display first (☞ P.33).

Press “a” on the 4-direction button. The displayed


2 image is enlarged.

• Pressing “ b ” on the 4-direction button returns enlarged image to its


original size.
• Press “d” or “ c ” on the 4-direction button to play back another image.
• Press the “CANCEL” button to return to viewing images at normal size.
• The maximum playback magnification varies depending on the image file
size.

3 To zoom in on another part of the enlarged image,


press the “PLAY” button to display the cursor and then
press “a”, “b ”, “d” or “c” on the 4-direction button to
display the area you want to view.
• To remove the cursor and return to the normal enlarged display screen,
press the “PLAY” button again or press the “CANCEL” button.

Downloaded from ManualsCamera.com Manuals


32
Multi-frame Playback
In multi-frame playback, image display can be set to “4-MULTI”, which
displays 4 image frames at one time, or “9-MULTI”, which displays 9 image
frames at one time.
Multi-frame playback provides a convenient way of selecting images for frame
erase, frame protect and DPOF frame settings.
If you press the “PLAY” button after you have pressed the button to erase a
frame from multi-frame playback or the button to protect a frame, you can
review a single frame playback.

1 Press the “PLAY” button to display the recorded image


on the color LCD monitor.

2 Press the “MENU/EXE” button to display the menu.

Press “d” or “c” on the 4-direction button to display


3 the “MULTI PLAY” menu.

Downloaded from ManualsCamera.com Manuals


33
Playing Back Photographed Images - continued

Press “a” or “b ” on the 4-direction button to select


4 “4-MULTI” or “9-MULTI”.

5 Press the “MENU/EXE” button to begin multi-frame


playback.

• The display shows the selected multi-frame playback display.

4-MULTI 9-MULTI

• To return to single-frame playback, select “OFF” in the “MULTI PLAY”


menu.

Downloaded from ManualsCamera.com Manuals


34
Erasing Single Recorded Images
Use the procedure below to erase recorded images.
To erase all the recorded images, see P.86.

1 Display the image to be erased. (See “To View Images


(Playback)”.)

2 When you press function button [2], the image is


displayed on the rear display panel for erase
confirmation.

• If the image is protected (☞ P.88), the error tone sounds and an error
message is displayed for about 3 seconds.
• If DPOF settings have been specified for the image, the error tone
sounds and an erase confirmation message is displayed. Check the
image and then proceed to step 3.

3 Press function key [4] to erase the selected image. The


next recorded image then appears.
1

• To cancel the procedure, press function key [1].


• To from
Downloaded continue erasing images, repeat
ManualsCamera.com steps 2 and 3.
Manuals
35
Playing Back Photographed Images - continued

Viewing Images on a TV

1 Switch the camera and the TV off. Plug the enclosed


video cable into the VIDEO OUT socket on the camera.

VIDEO OUT socket

• If there is a power outlet handy, the optional AC Power Adapter AC-5VH


should be connected.

2 Plug the pin-plug end of the video cable into the video
input socket on the TV and switch on the camera and
the TV. You can then take pictures and play back
images in the usual way.

To video
input socket

• Refer to the instructions for your TV for information on the video input
socket.

Downloaded from ManualsCamera.com Manuals


36
Background: A Brief Guide Focusing and Exposure
Focusing, exposure and exposure metering are key factors in taking
photographs. By understanding these aspects of photography, you can
achieve a wider range of photographic effects.
■ Focus and Depth of Field
When you focus the camera on a point, an area in front of and behind that
point is also in focus. This area is referred to as the depth of field and varies
depending on factors such as the distance to the subject, the focal length of
the lens and the aperture setting. In particular, narrowing the lens aperture
(selecting a higher f-stop) increases the distance over which objects are in
focus, giving what is referred to as a large depth of field. Conversely, widening
the lens aperture (selecting a lower f-stop) decreases the distance over which
objects are in focus, giving a shallow depth of field (☞ P.67).
■ Exposure
Exposure refers to the process by which light from the subject (the person or
object being photographed) passes through the camera lens, hits the film
(CCD) and is recorded. During this process, it is important that the sensitivity
of the CCD in the camera is matched to the brightness of the subject and that
the shutter speed and aperture are adjusted so that the correct amount of light
reaches the CCD (correct exposure).
To ensure optimum exposure, the FinePix S1 Pro is provided with a number of
exposure modes. These include the AUTO, programmed auto and image
program modes, in which the camera sets both the focus and the aperture
setting, the shutter-priority auto mode, in which the photographer sets the
shutter speed and the camera sets the exposure, the aperture-priority auto
mode, in which the photographer sets the exposure and the camera sets the
shutter speed, and manual mode, in which the photographer sets both the
shutter speed and the aperture setting by referring to the camera’s exposure
meter (☞ P.64).
■ Exposure Metering
The action of measuring the brightness of the subject (the person or object
being photographed) is referred to as exposure metering. Exposure metering
is an important source of information for determining the exposure. This
information is used to determine the combination of shutter speed and
aperture settings that will allow the optimum amount of light to hit the CCD. 1
Because the distribution of light in the image that includes the subject is not
necessarily uniform, the FinePix S1 Pro divides the image into 6 sections and
provides 2 types of exposure metering. These are “multi-pattern metering”, in
which the optimum exposure is determined using independently measured
light information for each section, and “center-weighted metering”, in which the
exposure metering information for the central part of the image is emphasized
in determining the optimum exposure.
If a D-type AF Nikkor lens is mounted on the camera, and additional metering
mode called “3D 6-zone multi-pattern metering” is available in which distance
information is also considered (☞ P.69).

Downloaded from ManualsCamera.com Manuals


37
2 Setup
Setup Functions
Settings available from the rear display panel

Setting Display Factory Description Ref.


Default Page
White AUTO, Sunny, AUTO Specify this setting to take pictures P.40
balance Shade, Fluorescent 1, with the white balance fixed to
Fluorescent 2, match the ambient light (indoor or
Fluorescent 3, outdoor) when the picture is taken.
Incandescent,
Custom

Sensitivity 320, 400, 800, 1600 400 Specify this setting when you want P.42
to shoot using a fast shutter speed
(to prevent camera shake) or when
you want to take bright pictures
indoors without using the flash.

Quality Basic, Normal, Fine, Normal Use this setting to specify the P.43
Hi image quality.

Image size 3040, 2304, 1440 3040 Use this setting to specify the P.44
(number of number of pixels in the image (the
pixels) image size).

Color STD, HIGH, ORG, STD Use this setting to specify the P.45
B/W density of the colors in the image.

Tone STD, HARD, ORG STD Use this setting to specify the P.46
image contrast.

Sharpness STD, HARD, OFF STD Use this setting to specify the P.47
image sharpness.

Multi- OFF, ON OFF Use this setting to specify whether P.48


exposure multi-exposure photography is
performed.
• If you switch the camera off when the data and time have not been set (☞P.22),
the settings specified from the rear display panel and from the “SET-UP” menu on
the color LCD monitor revert to the factory default settings.

Downloaded from ManualsCamera.com Manuals


38
Settings that can be specified in the “SET-UP” menu on the color LCD
monitor
Setting Display Factory Description Ref.
Default Page
PREVIEW OFF, OFF Use this setting to specify whether P.49
MANUAL REC, previews of photographed images
AUTO REC are displayed for checking.

CUSTOM EXE — Use this setting to specify an P.50


WB independent white balance setting.

Hi MODE TIFF-RGB, TIFF-YC TIFF- When “Hi” is specified as the P.51


RGB Quality setting, use this setting to
specify whether the TIFF format
used is “RGB” data or “YC” data.

MEDIA SmartMedia, Smart Use this setting to specify the type P.51
CF Type II Media of media used.

SELF 2 sec., 10 sec. 10 sec. When you take pictures using the P.52
TIMER self-timer, use this setting to
specify the interval between the
shutter button being pressed and
the picture being taken.

AUTO 2 min., 5 min., OFF 2 min. Use this setting to specify whether P.52
POWER the camera automatically switches
OFF off when it is not used and, if so,
the interval after which it switches
off.

FRAME No. ON, OFF OFF Use this setting to specify whether P.53
the frame number memory function
is used.

PC MODE DOWNLOADING, DOWN- Use this setting to specify PC P.54


SHOOTING LOADING mode.

BEEP OFF, HIGH, LOW HIGH Use this setting to specify the P.54
setting for the camera tone.

LANGUAGE JAPANESE, ENGLISH Use this setting to specify the P.55


ENGLISH language used for “SET-UP” menu
display. 2
DATE/TIME EXE — Use this setting to specify the date P.22
and time.

RESET EXE — Use this setting to reset the settings P.55,


specified from the color LCD 56
monitor and rear display panel.

Downloaded from ManualsCamera.com Manuals


39
Rear Display Panel Setting the White Balance

■ By setting the optimum white balance for a variety of light sources,


pictures can be taken that show the natural colors of the subject while
also capturing the atmosphere of the shot.

1 Press the “FUNC” button.

2 The icon for the white balance setting appears on


the rear display panel. Press function button [1].

With the white balance set to “AUTO”


• The display changes in the cycle shown below each time function button
[1] is pressed.

[AUTO] [Custom]

[Sunny] [Incandescent]

[Shade] [Fluorescent 3]

[Fluorescent 1] [Fluorescent 2]

• The same settings can also be selected by holding down function button
[1] and pressing “ a” on the 4-direction button. You can select settings in
the reverse order by holding down function button [1] and pressing “ b ” on
the 4-direction button.

Downloaded from ManualsCamera.com Manuals


40
Display Name Description

AUTO The camera automatically determines the amount of light and


(default) the color information for the shot and takes the picture with a
natural white balance.

Sunny Select this setting for outdoor shots in fine weather when the
light source for the shot is the sun.

Shade Select this setting for shots taken in shade or on cloudy days.

Fluorescent 1 Select this setting for shots taken under “Daylight” fluorescent
lamps.

Fluorescent 2 Select this setting for shots taken under “Warm White”
fluorescent lamps.

Fluorescent 3 Select this setting for shots taken under “Cool White” fluorescent
lamps.

Incandescent Select this setting for shots when the light source is
incandescent bulbs or lights.

Custom This setting uses the white balance setting specified by the
photographer in the “SET-UP” menu (☞P.50).

• Because white balance settings other than “Custom” are disabled when
the flash is used, do not use the flash if you want to achieve a particular
effect in your shot.

Downloaded from ManualsCamera.com Manuals


41
Rear Display Panel Setting the Sensitivity
■ The ISO sensitivity (film speed) can be set to 320, 400, 800 or 1600.

1 Press the “FUNC” button.

2 The icon for the ISO sensitivity setting appears on


the rear display panel. Press function button [2].

With the ISO sensitivity set to “ISO400”


• The display changes in the cycle shown below each time function button
[2] is pressed.

320 1600

400 800

• The same settings can also be selected by holding down function button
[2] and pressing “ a” on the 4-direction button. You can select settings in
the reverse order by holding down function button [2] and pressing “ b ” on
the 4-direction button.

Display Name Description


ISO320 Sets the ISO sensitivity to 320.

ISO400 Sets the ISO sensitivity to 400.


(default)

ISO800 Sets the ISO sensitivity to 800.

ISO1600 Sets the ISO sensitivity to 1600.

Downloaded from ManualsCamera.com Manuals


42
Rear Display Panel Setting the Image Quality
■ Use the procedure below to set the image quality.
Selecting a high image quality decreases the number of images that
can be saved. Conversely, selecting a low image quality increases the
number of images that can be saved.

1 Press the “FUNC” button.

2 The icon for the quality setting appears on the


rear display panel. Press function button [3].

With the quality set to “Normal”


• The display changes in the cycle shown below each time function button
[3] is pressed.

Normal Basic

Fine Hi

• The same settings can also be selected by holding down function button
[3] and pressing “ a” on the 4-direction button. You can select settings in
the reverse order by holding down function button [3] and pressing “ b ” on
the 4-direction button.

Display Name Description


Basic This setting records images at the lowest image quality but also
allows the largest number of images to be recorded.

Normal This setting records images at the 3rd highest image quality.
2
(default) This setting allows more images to be saved than is possible
with the “Fine” setting.

Fine This setting records images at the next highest image quality
after “Hi” and allows more images to be saved than is possible
with the “Hi” setting.

Hi This setting records images uncompressed at the highest image


quality. With this setting, the fewest images can be recorded.
Downloaded from ManualsCamera.com Manuals
43
Rear Display Panel Setting the Image Size (Number of Pixels)
■ Use the procedure below to set the number of pixels (image size) used
to record photographed images.

1 Press the “FUNC” button.

2 The icon for the image size (number of pixels)


setting appears on the rear display panel. Press
function button [4].

With the image size (number of pixels) set to “3040 × 2016 pixels”
• The display changes in the cycle shown below each time function button
[4] is pressed.

3040
1440
2304

• The same settings can also be selected by holding down function button
[4] and pressing “ a” on the 4-direction button. You can select settings in
the reverse order by holding down function button [4] and pressing “ b ” on
the 4-direction button.
Display Name Description
3040 This setting sets the image size to 3040 × 2016 pixels. At this
(default) setting, the smallest number of images can be recorded.

2304 This setting sets the image size to 2304 × 1536 pixels.

1440 This setting sets the image size to 1440 × 960 pixels. At this
setting, the largest number of images can be recorded.

Downloaded from ManualsCamera.com Manuals


44
Rear Display Panel Setting the Color
■ Use the procedure below to set the density of the color used when
images are shot.

1 Press the “FUNC” button twice.

2 The icon for the color setting appears on the rear


display panel. Press function button [1].

With the color set to “STD”


• The display changes in the cycle shown below each time function button
[1] is pressed.

STD B/W

HIGH ORG

• The same settings can also be selected by holding down function button
[1] and pressing “ a” on the 4-direction button. You can select settings in
the reverse order by holding down function button [1] and pressing “ b ” on
the 4-direction button.

Display Name Description


STD This setting sets the standard color density.
(default)

HIGH This setting provides a higher color density than the “STD”
setting.
2
ORG This setting specifies a lower color density than the “STD”
setting. Use this setting for images that will undergo image
processing for use in commercial printing.

B/W This setting converts the colors in the photographed image to


black and white.

• If you want to view or print the image data directly, do not select “ORG”.
Downloaded from ManualsCamera.com Manuals
45
Rear Display Panel Setting the Tone
■ Use the procedure below to set the contrast when images are shot.

1 Press the “FUNC” button twice.

2 The icon for the tone setting appears on the rear


display panel. Press function button [2].

With the tone set to “STD”


• The display changes in the cycle shown below each time function button
[2] is pressed.

STD
ORG
HARD

• The same settings can also be selected by holding down function button
[2] and pressing “ a” on the 4-direction button. You can select settings in
the reverse order by holding down function button [2] and pressing “ b ” on
the 4-direction button.

Display Name Description


STD This setting sets the contrast for photographed images to the
(default) standard level.

HARD Use this setting for images that will undergo image processing
for use in commercial printing. This setting provides a higher
level of contrast than the “STD” setting.

ORG This setting specifies a lower contrast than the “STD” setting.
Use this setting for images that will undergo image processing
for use in commercial printing.

• If you want to view or print the image data directly, do not select “ORG”.

Downloaded from ManualsCamera.com Manuals


46
Rear Display Panel Setting the Sharpness
■ Use this setting to soften or sharpen the outlines in an image and to
adjust the quality of the photographed image.

1 Press the “FUNC” button twice.

2 The icon for the sharpness setting appears on the


rear display panel. Press function button [3].

With the sharpness set to “STD”


• The display changes in the cycle shown below each time function button
[3] is pressed.

STD
OFF
HARD

• The same settings can also be selected by holding down function button
[3] and pressing “ a” on the 4-direction button. You can select settings in
the reverse order by holding down function button [3] and pressing “ b ” on
the 4-direction button.
Display Name Description
STD This setting applies the optimum level of sharpness for normal
(default) shots.

HARD This setting sharpens the outlines in an image and is best for
images of subjects such as buildings or text where clarity is
important. 2
OFF Sharpness processing is not applied in this setting. Use this
setting for images that will undergo image processing for use in
commercial printing.

• If you want to view or print the image data directly, do not select “OFF”.

Downloaded from ManualsCamera.com Manuals


47
Rear Display Panel Setting Multi-exposure
■ Use this setting to specify whether to use multi-exposure photography
(☞ P.84).

1 Press the “FUNC” button twice.

2 The icon for the multi-exposure setting appears


on the rear display panel. Press function button [4].

With multi-exposure photography set to “OFF”


• The display changes in the cycle shown below each time function button
[4] is pressed.

OFF ON

Display Name Description


OFF Select this setting when you do not want to use multi-exposure
(default) photography.

ON Select this setting when you want to use multi-exposure


photography.

Downloaded from ManualsCamera.com Manuals


48
SET-UP Menu Part 1 Preview
■ This setting specifies whether or not a preview image is displayed after
you take a picture.

1 Press the “MENU/EXE” button. The “SET-UP” menu


appears on the color LCD monitor.

SET-UP menu Part 1 SET-UP menu Part 2 (☞P.53)

Press “a” or “b ” on the 4-direction button to select


2 “PREVIEW” and then use “d” or “c” on the 4-direction
button to select the “PREVIEW” setting.
Name Description
OFF Images are automatically recorded with no preview image displayed.
(default)

MANUAL REC A preview image is displayed and you can select whether to record the
image.
• To record the image, press function button [1].
• To proceed without recording the image, press function button [2].

AUTO REC A preview image is displayed for about 1 second and the image is
automatically recorded.

• If you record images with preview image display specified, you cannot
operate the shutter again until recording is completed.

3 When you have selected the setting, select “END” and


press the “MENU/EXE” button.
2
☞ Note
Preview “MANUAL REC” Function
• The preview “MANUAL REC” function is convenient as a way of checking the
exposure and aligning the angle of view, but the image is not recorded unless
you instruct the camera to do so. For normal photography, you should use the
“OFF” or “AUTO REC” setting.

Downloaded from ManualsCamera.com Manuals


49
SET-UP Menu Part 1 Specifying a Custom WB Setting
■ Use the procedure below to specify a custom white balance setting.

1 Press the “MENU/EXE” button.

Press “a” or “b ” on the 4-direction button to select


2 “CUSTOM WB” and then press the “MENU/EXE” button
or “d” or “c” on the 4-direction button.
• The “SET OK?” message appears on the color LCD monitor.
• Set the focus mode selector switch to “M” (manual focus) (☞ P.58).

3 Photograph a reference white image, such as a sheet of


white paper, that occupies an area larger than the
center-weighted metering area (☞P.15). A message
then appears indicating whether the photographed
image is valid.
• If the photographed image is not valid, respond to the message displayed
as follows:
: The subject is too bright. Apply exposure compensation
in the negative (–) direction, select a darker subject or
reduce the light level. Then repeat the procedure from
step 3.
: The subject is too dark. Apply exposure compensation
in the positive (+) direction, select a brighter subject or
increase the light level. Then repeat the procedure from
step 3.
: The image exceeds the compensation range for the
custom WB setting. The maximum compensation value
is set. To reset the value, press the “CANCEL” button
and repeat the procedure from step 3.
• The color temperature range within which the white balance can be
matched is approximately 2800K to 9500K.

4 When the photographed image is valid (when


displayed), press the “MENU/EXE” button.
is

If the image is not valid, use one of the solutions given


in step 3.
• To cancel the setting procedure, press the “CANCEL” button.

5 When you have finished setting the custom white


balance, use “a” or “b ” on the 4-direction button to
select “END” and then press the “MENU/EXE” button.

Downloaded from ManualsCamera.com Manuals


50
SET-UP Menu Part 1 Hi MODE/MEDIA

Hi MODE
This setting specifies the TIFF data format when “Hi” is selected as the image
quality setting.

1 Press the “MENU/EXE” button.

Press “a” or “b ” on the 4-direction button to select “Hi


2 MODE” and then press “d” or “c” on the 4-direction
button to select the “Hi MODE” setting.
Name Description
TIFF-RGB This setting selects RGB data as the TIFF format (☞ P.110)
(default)

TIFF-YC This setting selects YC data as the TIFF format (☞ P.110)

• To use a TIFF-YC image on your personal computer, you must have an


application that supports the TIFF-YC format (such as the USB software
supplied).

When you have selected the setting, use “a” or “b” on


3 the 4-direction button to select “END” and then press
the “MENU/EXE” button.

MEDIA
This setting specifies whether images are recorded on to a SmartMedia
(default setting) or a Microdrive/CompactFlash (CF Type II).

1 Press the “MENU/EXE” button.

Press “a” or “b ” on the 4-direction button to select


2 “MEDIA” and then press “d” or “c” on the 4-direction
button to select the media type.
2
When you have selected the media type, use “a” or “b ”
3 on the 4-direction button to select “END” and then
press the “MENU/EXE” button.
• When only one media is loaded into the camera, images are recorded
onto that media regardless of the setting selected here.

Downloaded from ManualsCamera.com Manuals


51
SET-UP Menu Part 1 SELF TIMER/AUTO POWER OFF

SELF TIMER
Use this setting to select either 2 seconds or 10 seconds (default setting) as
the interval after which the shutter is released during self-timer photography.
See P.72 for information on self-timer photography.

1 Press the “MENU/EXE” button.

Press “a” or “b ” on the 4-direction button to select


2 “SELF TIMER” and then press “d” or “c” on the
4-direction button to select the time interval (2 sec. or
10 sec.).
When you have selected the time interval, use “a” or
3 “b ” on the 4-direction button to select “END” and then
press the “MENU/EXE” button.
• Setting a 2-second delay in self-timer photography is useful as a way of
avoiding camera shake when using a tripod.

AUTO POWER OFF


Use this setting to specify whether the camera automatically switches off when
it is not being used.

1 Press the “MENU/EXE” button.

Press “a” or “b ” on the 4-direction button to select


2 “AUTO POWER OFF” and then press “d” or “c” on the
4-direction button to select the “AUTO POWER OFF”
setting.
Name Description
2 min. The camera automatically switches off after 2 minutes when left unused.
(default)
5 min. The camera automatically switches off after 5 minutes when left unused.
OFF The Auto Power Off function is cancelled.

• Regardless of the setting selected here, the Auto Power Off function does
not operate during automatic playback or when a USB connection is used.

When you have selected the setting, use “a” or “b ” on


3 the 4-direction button to select “END” and then press
the “MENU/EXE” button.
Downloaded from ManualsCamera.com Manuals
52
SET-UP Menu Part 2 FRAME No.
■ The frame number memory function stores the last file number saved
onto a media (SmartMedia or Microdrive) so that when a new media is
loaded, file numbers are assigned beginning from that stored file
number. The “FRAME No.” setting specifies whether this function is
used.

1 Press the “MENU/EXE” button.

Press “a” or “b ” on the 4-direction button to select


2 “FRAME No.” and then press “d” or “c” on the 4-
direction button to select the frame number memory
setting.

3 When you have selected the setting, select “END” and


press the “MENU/EXE” button.
Name Description
OFF Images are stored starting with file number 0001 on each media.
(default)

ON Images are stored starting with the last file number on the last media
used.

B
When a formatted SmartMedia is used for both A and B

• When a new media already contains an image with a file number higher
than the last file number stored by the frame number memory function, 2
new images are stored beginning from the higher file number.

Downloaded from ManualsCamera.com Manuals


53
SET-UP Menu Part 2 PC MODE/BEEP

PC MODE
When the camera is connected to a personal computer, this setting specifies
whether images are downloaded from the camera to the computer or
photography using the camera is controlled from the computer.

1 Press the “MENU/EXE” button.

Press “a” or “b ” on the 4-direction button to select


2 “PC MODE” and then press “d” or “c” on the 4-
direction button to select the “PC MODE” setting.

When you have selected the setting, use “a” or “b ” on


3 the 4-direction button to select “END” and then press
the “MENU/EXE” button.
Name Description
DOWNLOADING Select this setting to download images from the camera to the
(default) personal computer.

SHOOTING Select this setting to control photography using the camera from the
computer.

• See P.111 for information on connecting the camera to a personal


computer.

BEEP
Use the procedure below to set the camera beep to “HIGH” (default setting),
“LOW” or “OFF”.

1 Press the “MENU/EXE” button.

Press “a” or “b ” on the 4-direction button to select


2 “BEEP” and then press “d” or “c” on the 4-direction
button to select the beep setting.

When you have selected the setting, use “a” or “b ” on


3 the 4-direction button to select “END” and then press
the “MENU/EXE” button.

Downloaded from ManualsCamera.com Manuals


54
SET-UP Menu Part 2 LANGUAGE/RESET

LANGUAGE
Use the procedure below to select the language used only in the “SET-UP”
menu display. (Menus other than the “SET-UP” menu are shown only in
English (default setting) and cannot be set to Japanese-language display.)

1 Press the “MENU/EXE” button.

Press “a” or “b ” on the 4-direction button to select


2 “LANGUAGE” and then press “d” or “c” on the 4-
direction button to select the language setting.

When you have selected the setting, use “a” or “b ” on


3 the 4-direction button to select “END” and then press
the “MENU/EXE” button.

RESET
This setting resets the settings specified on the color LCD monitor and rear
display panel.

1 Press the “MENU/EXE” button.

Press “a” or “b ” on the 4-direction button to select


2 “RESET”.

3 To reset the settings you have selected in the menu,


press the “MENU/EXE” button. The “RESET OK?”
message appears.
• A list of the items that are reset is given on P.56.

4 Press the “MENU/EXE” button to reset the settings. To


retain the current settings, press the “CANCEL” button.

When you have selected the setting, use “a” or “b” on


2
5 the 4-direction button to select “END” and then press
the “MENU/EXE” button.

Downloaded from ManualsCamera.com Manuals


55
RESET - continued/Camera Reset
Items reset by the “RESET” setting
• Items set from the color LCD monitor
• Items set from the rear display panel menu
Item After Reset Item After Reset
White balance AUTO PREVIEW OFF
Sensitivity 400 Hi MODE TIFF-RGB
Quality Normal MEDIA SmartMedia
Image size 3040 SELF TIMER 10 sec.
(number of pixels)
AUTO POWER OFF 2 min.
Color STD
FRAME No. OFF
Tone STD
PC MODE DOWNLOADING
Sharpness STD
BEEP HIGH
Multi-exposure OFF
LANGUAGE ENGLISH

MULTI PLAY (Multi-


OFF
frame Playback Mode)

Camera Reset
Use the procedure below to reset the settings specified on the top display
panel.

1 Hold down the exposure compensation button “h” and


aperture button “g” for 2 or more seconds.

Functions reset from the camera


Function After Reset
Program Shift Cancelled.

Exposure Compensation Cancelled.

Synchro Mode Slow synchro used when the exposure mode is Night Scene
(5-vari program). Normal Synchro otherwise.

Self-timer Cancelled.

• See P.80 for the initial function statuses and function combinations.
Downloaded from ManualsCamera.com Manuals
56
3 Advanced
Photography Focusing Modes

When the Focusing Mode is Set to AF (auto focus)

• If you set the focus mode selector switch to AF and hold the shutter button
halfway, the camera automatically focuses on the subject and the focus
indicator “●” appears in the viewfinder display to notify you that the camera
has focused on the subject.
Auto AF servo (AF-A):
In this mode, the camera automatically determines whether the subject is
moving and, if so, in which direction the subject is moving, and then selects
either single AF servo (AF-S) or continuous AF servo (AF-C) accordingly.
• Single AF Servo (AF-S):
The camera focuses on the subject and then fixes the focus (focus lock).
• Continuous AF Servo (AF-C):
Focusing tracks the movements of the subject.
• In either mode, the shutter does not release unless the focus indicator
appears.
• When you select Sport mode (5-vari program) as the exposure mode,
focusing is set to continuous AF servo from the outset and focusing tracks
the movements of the subject.

Auxiliary AF Light

0.5 - 3 m
(1.6 - 9.8 ft.)

• If the subject is dark, the auxiliary AF light automatically switches on when


the shutter button is pressed halfway to illuminate the subject and enable
auto focusing. The auxiliary AF light operates under the following conditions:
1. When the focusing mode is AF, an AF Nikkor lens is mounted on the
camera and the subject is dark.
3
2. When an exposure mode other than Landscape mode or Sport mode is
selected.

Downloaded from ManualsCamera.com Manuals


57
Focusing Modes - continued

When these conditions are met, the auxiliary AF light operates automatically.
This function cannot be cancelled. The auxiliary AF light can be used with AF
Nikkor lenses that have focal lengths between 24 and 200 mm. In general, the
effective range of the auxiliary AF light is 0.5 to 3 m (1.6 to 9.8 ft.).

☞ Note
Continuous use of the auxiliary AF light
If you use the auxiliary AF light continuously, the illuminating lamp temporarily
switches off to protect the lamp. You can continue using the lamp after a slight
delay.

✎ Important
Nikon flash units and active auxiliary flash
If you use a Nikon flash equipped with active auxiliary flash and take pictures
using TTL mode, the active auxiliary flash on the Nikon flash is automatically
used. See P.78 for information on the Nikon flash models that can be used.

When M (manual focus) is Selected

• Set the focus mode selector switch to M and focus the camera by turning the
focusing ring on the lens until the image can be seen clearly in the matt
surface of the viewfinder screen. The shutter can be released regardless of
whether the focus indicator “●” lights. Use manual focus for subjects that are
not suitable for auto focusing or when a lens other than an AF Nikkor lens is
mounted on the camera (☞ P.107).

✎ Important
Focus Aid
If the lens mounted has an f-step setting brighter than f/5.6 when the focusing
mode is set to M (manual focus), the “focus aid focusing” feature allows the
focus to be checked using the focus display in the viewfinder. Turn the
focusing ring on the lens so that the focus indicator “●” lights. The shutter
button can be released at any point.

Downloaded from ManualsCamera.com Manuals


58
Focus Lock Photography

■ If you are using AF (auto focus) to focus the camera, use the focus
lock feature when you are composing a picture in which your main
subject (the object or person you are focusing on) is not inside the
focusing frame. This technique can also be used to focus on subjects
that are not suitable for auto focusing.

1 Position the focusing frame over the object or person


on which you want to focus and press the shutter
button halfway.

• When the camera is focused, the focus indicator “●” lights and the focus
stays locked as long as the shutter button is held halfway.
• If the selected exposure mode is Sport mode (5-vari program), focus lock
photography cannot be used.
• If you want to use focus lock when a moving subject stops moving (when
the focusing mode changes from continuous AF to single AF servo),
release the shutter button and then press the shutter button halfway
again.

2 When the focus indicator “●” lights, keep the shutter


button held halfway as you compose the picture and
then take the picture.

3
• Once the focus indicator “●” lights, do not change the distance between
the camera and the main subject. If you keep your finger on the shutter
button and keep the button held down after the shutter has released, you
can take any number of shots with the focus fixed at the same setting.
Downloaded from ManualsCamera.com Manuals
59
Shooting Using Exposure Modes

z: AUTO
This exposure mode is the easiest to use for
taking pictures since the photographer can
leave the exposure settings to the camera.
This exposure mode is recommended for
people using an SLR camera for the first
time.
See P.80 for information on using this mode
with other functions.

1 Set the exposure mode dial to “z”.

• When you select z (AUTO mode), the following function statuses apply:
Metering mode : Multi-pattern metering (☞ P.69)
Flash : j Normal synchro mode (☞ P.74)
• The program shift, exposure compensation and slow synchro functions
cannot be selected.

2 Check that the focus indicator “●” is lit and take the
picture.
• If one of the following warnings appears on the top display panel or
viewfinder display, the subject is too bright or too dark and is beyond the
camera control range.
• ⁄ : Use an ND (light volume adjustment) filter.
• ¤ : Use the flash.

✎ Important
Differences between AUTO and Programmed auto
Both modes use the same exposure control method, but the programmed auto
mode allows greater flexibility in the photography settings since program shift
(☞ P.61), exposure compensation (☞ P.71) and slow synchro (☞ P.75) can
also be set.

Downloaded from ManualsCamera.com Manuals


60
P: Programmed Auto
In this mode, the camera automatically
controls the exposure to give the optimum
exposure for the photography conditions.
This mode can be used in combination with
program shift or exposure compensation
(☞ P.71) for better quality pictures.
See P.80 for information on using this mode
with other functions.

1 Set the exposure mode dial to “P”.

2 Check that the focus indicator “●” is lit and take the
picture.
• If one of the following warnings appears on the top display panel or
viewfinder display, the subject is too bright or too dark and is beyond the
camera control range.
• ⁄ : Use an ND (light volume adjustment) filter.
• ¤ : Use the flash.

✎ Important
Program Shift
By turning the command dial
during programmed auto mode
photography, you can change the
combination of shutter speed and
aperture while maintaining the
same exposure, providing
operation that is equivalent to the
shutter-priority auto and aperture-
priority auto modes. During program shift, “f” is displayed on the top display
panel. To cancel program shift, reset shutter speed and aperture settings to
3
their original values, select another exposure mode, switch the camera off,
use the built-in flash (☞ P.74) or perform a camera reset (☞ P.56).

Downloaded from ManualsCamera.com Manuals


61
Shooting Using Exposure Modes - continued

S: Shutter-priority Auto
In this mode, the photographer sets the
shutter speed (1/2000 to 30 sec.) and the
camera automatically controls the aperture
setting. This mode is best for photographs
where the shutter speed is the main priority,
such as subjects in sports scenes where
you want a fast shutter speed to freeze one
moment of the action, or where you want a
slow shutter speed to emphasize the sense
of movement.
See P.80 for information on using this mode
with other functions.

1 Set the exposure mode dial to “S” and set the shutter
speed on the command dial (1/2000 to 30 sec.).

2 Check that the focus indicator “●” is lit and take the
picture.
• If one of the following warnings appears on the top display panel or
viewfinder display, the subject is too bright or too dark and is beyond the
camera control range.
• ⁄ : Set a faster shutter speed. If the warning still appears with the
faster shutter speed, use an ND (light volume adjustment) filter.
• ¤ : Set a slower shutter speed. If the warning still appears with the
slower shutter speed, use the flash.
• Pressing the “CANCEL” button during a long-exposure shot does not
interrupt the shot.

Downloaded from ManualsCamera.com Manuals


62
A: Aperture-priority Auto
In this mode, the photographer sets the
aperture (narrowest aperture to widest
aperture) and the camera automatically
controls the shutter speed. This mode is
best for photographs where the depth of
field is the main priority, such as shots
where you both near and distant objects in
clear focus or where you want the
background out of focus. You can also use
this mode to vary the flash control range by
changing the aperture when you are taking
pictures with the flash (☞ P.74).
See P.80 for information on using this mode
with other functions.

1 Set the exposure mode dial to “A” and set the aperture
setting (narrowest aperture to widest aperture) on the
command dial.

2 Check that the focus indicator “●” is lit and take the
picture.
• If one of the following warnings appears on the top display panel or
viewfinder display, the subject is too bright or too dark and is beyond the
camera control range.
• ⁄ : Set a higher aperture setting. If the warning still appears with the
higher aperture setting, use an ND (light volume adjustment) filter.
• ¤ : Set a lower aperture setting. If the warning still appears with the
lower aperture setting, use the flash.

Downloaded from ManualsCamera.com Manuals


63
Shooting Using Exposure Modes - continued

M: Manual
In this mode, the photographer can set any
shutter speed (1/2000 to 30 sec.) and any
aperture setting (narrowest aperture to
widest aperture). This allows the
photographer to determine the exposure to
suit the conditions and the desired goals
while watching the exposure indicator in the
viewfinder.
See P.80 for information on using this mode
with other functions.

1 Set the exposure mode dial to “M” and compose the


picture.

• M: In manual mode, the metering mode is automatically switched from


multi-pattern metering to center-weighted metering (☞ P.69).

2 Set the shutter speed and aperture setting while


watching the exposure indicator in the viewfinder.

• Set the shutter speed (1/2000 to 30 sec.) on the command dial.


• Set the aperture setting (narrowest aperture to widest aperture) by using
the command dial while holding down the aperture button “g”.
• Either setting (shutter speed or aperture) can be set first.

Downloaded from ManualsCamera.com Manuals


64
✎ Important
Exposure Indicator
The figures at right show how to read Correctly exposed or over- or under-
the exposure indicator. The icons exposed by less than 0.5 EV steps
show the difference between the
value given by the combination of
shutter speed and aperture setting Under-exposed by 0.5 EV steps or
and the exposure value measured by more but less than 1.5 EV.
the camera.

Over-exposed by 1.5 EV or more

3 Check that the focus indicator “●” is lit and take the
picture.
• Lenses other than a Nikkor lens with a built-in CPU can only be used in
this mode. However, the camera’s exposure meter cannot be used and
the aperture cannot be set using the aperture button and command dial.
See “Lenses that Can Be Used with this Camera” on P.106 for details.

Downloaded from ManualsCamera.com Manuals


65
Shooting Using 5-Vari Programs

5-Vari Programs
The 5-vari programs provide programs for each mode that make it easy for
you to take pictures that capture your desired image. The programs tailor the
camera settings to particular scenes or subjects by selecting shutter speeds
matched to the subject’s movement and aperture settings that allow for the
depth of field (focusing depth) and even the focusing characteristics of the
lens.
See P.80 for information on using 5-vari programs with other functions.

Taking Pictures Using 5-Vari Programs


Set the exposure mode dial to the desired 5-vari
program, check that the focus indicator “●” is lit, and
then take the picture.

• If one of the following warnings appears on the top display panel or


viewfinder display, the subject is too bright or too dark and is beyond the
camera control range.
• ⁄ : Use an ND (light volume adjustment) filter.
• ¤ : Use the flash.

☞ Note
Points to note when using 5-vari programs
Program shift (☞ P.61) and exposure compensation (☞ P.71) are both
cancelled in the 5-vari program modes. If you use the flash, the synchro mode
is automatically switched according to the mode (☞ P.76).

Downloaded from ManualsCamera.com Manuals


66
5-Vari Program Types and Features

x: Portrait mode
By using exposure control with a wide
aperture (a low aperture number), this mode
keeps a shallow depth of field (restricting the
range of focus in front of and behind the
subject). This allows you to take pictures in
which your subject stands out clearly against
a softly blurred background, giving a feeling
of depth in the shot.
Recommended lens: The most effective
lenses for this mode are bright telephoto lenses in the 50 to 135 mm range.

c: Landscape mode
By using exposure control with a narrow
aperture (a high aperture number), this mode
give a large depth of field (extending the
range of focus in front of and behind the
subject) to allow you to take pictures of
scenery in which the both near and distant
objects are in sharp focus.
Lenses from wide-angle through to telephoto
can be used in this mode.
• In some photography conditions care is needed to avoid camera shake since
a slow shutter speed may be used. (A tripod should be used in such
situations.)

v: Close-up mode
This mode uses exposure control with a wide
aperture to give a relatively shallow depth of
field so that you can take close-up shots in
which your subject stands out clearly against
a softly blurred background.
Recommended lens: The most effective
lenses for this mode are the Micro Nikkor
lenses.
• In some photography conditions care is
needed to avoid camera shake since a slow shutter speed may be used.
3
(A tripod should be used in such situations.)

Downloaded from ManualsCamera.com Manuals


67
Shooting Using 5-Vari Programs - continued

b: Sport mode (continuous shooting)


This mode uses exposure control with a fast
shutter speed setting to freeze your subject
in a moment of rapid movement and allow
you to take shots of sporting events that
capture the feeling of fast-paced action.
Recommended lens: The most effective
lenses for this mode are telephoto lenses in
the 80 to 300 mm range.
• In Sport mode, the focusing mode switches
to continuous AF servo without focus lock so that the camera focus tracks
the movements of your subject. Also, if “PREVIEW” (☞P.49) is set to “OFF”,
the camera shoots pictures continuously for as long as the shutter button is
held down. The maximum number of continuous frames is 5.
• The shutter will not release if the number of available shots is highlighted.

☞ Note
Using continuous shooting when the number of remaining frames
displayed is small
If you use continuous shooting when the number of remaining frames displayed
is small, a warning beep may sound and the number of remaining frames
displayed may show 0 even when the number of shots taken is fewer than the
number of shots displayed when continuous shooting began.

n: Night scene mode


This mode uses exposure control that is
tailored to dimly lit subjects and allows you to
effectively capture beautiful evening or night
scenes.
Also, when you are shooting people against
an evening backdrop, you can use the flash
to capture both your subjects and the
background as they appear naturally.
Lenses from wide-angle through to telephoto
can be used in this mode.
• In some photography conditions care is needed to avoid camera shake since
a slow shutter speed may be used. (A tripod should be used in such
situations.)

Downloaded from ManualsCamera.com Manuals


68
Metering Modes

■ The FinePix S1 Pro normally uses multi-pattern exposure metering.


However, when the exposure mode is set to Manual or the AE lock
(☞ P.70) is used, exposure metering automatically switches to center-
weighted metering.

Multi-pattern Metering and 3D 6-zone Multi-pattern Metering

In multi-pattern metering, the image is divided into 6 zones as shown in the


figure above. Each of the 6 zones is measured independently and that
information is then used to determine the optimum exposure. When a D-type
AF lens is mounted on the camera, 3D 6-zone multi-pattern metering is used.
In this mode, information on the maximum brightness in the image and the
differences in brightness is also included, along with information on the
distance from the lens to the subject, to give heightened metering precision.
Except where the exposure mode is set to Manual or AE lock (☞ P.70), multi-
pattern metering is used for all shots.

Center-weighted Metering

In center-weighted metering, emphasis is placed on the central area of the


viewfinder (a circle roughly 12 mm in diameter) when the exposure is
measured to determine the exposure setting. Consequently, this mode is best
for shots where you want the area inside that 12 mm circle to be the exposure
reference. When the exposure mode is set to Manual (☞ P.64) or AE lock
(☞ P.70) is used, metering is automatically switched to this mode.

Downloaded from ManualsCamera.com Manuals


69
AE Lock Photography
■ AE lock allows you to set the exposure for a part of the image that you
want to be correctly exposed, and then lock in that exposure setting
when you take the picture. This technique is useful when you want to
store an exposure setting in the camera (by pressing the “AE-L” AE
lock button) and then keep the same exposure setting as you change
your subject’s pose or the composition of the shot. Regardless of the
selected exposure mode, the exposure metering mode is automatically
switched to center-weighted metering.

1 Position your subject in the center of the image, hold


the shutter button halfway and press the “AE-L” AE
lock button.

2 With the “AE-L” button held down, return to the shot


composition you want to photograph, focus the shot
and then take the picture.

Downloaded from ManualsCamera.com Manuals


70
Exposure Compensation

■ Exposure compensation is a procedure in which you can intentionally change the


correct exposure setting displayed by the camera. For example, this mode can
be used to shift the exposure in small steps when the subject has high levels of
contrast. On the FinePix S1 Pro, exposure compensation can be performed to ±3
EV in increments of 1/3 of an EV step. (Note that exposure compensation cannot
be used in AUTO mode or in the 5-vari program modes.)

1 Hold down the exposure compensation button “h ” and


set the amount of compensation on the command dial.
• Example of exposure indicator display

Compensation of –0.3 EV

Compensation of +2 EV

• When you set the amount of compensation, the exposure compensation icon
“h ” appears on the top display panel and in the viewfinder display. Simply
press the exposure compensation button to confirm the compensation
amount. (The exposure indicator is also displayed.)
• When the built-in flash or an external Nikon flash is used, the amount of light
emitted by the flash is also adjusted by the same amount. However, the
restrictions described below apply.
■ Maximum flash compensation ISO 320 400
values for flash units used + compensation 3 EV 3 EV
with exposure compensation – compensation approx. 1.5 EV approx. 1 EV

• As a general guide, when the subject (eg. a person) is set against a bright
background, positive exposure compensation should be used. Against a dark
background, negative exposure compensation should be used.

2 Compose the picture, focus and shoot.

3
• To cancel exposure compensation, hold down the exposure compensation
button and use the command dial to set the compensation amount to 0, or
reset the camera (☞ P.56). (Switching the camera off does not cancel
exposure compensation.)
Downloaded from ManualsCamera.com Manuals
71
Self-timer Photography
■ This mode is useful for shots such as commemorative pictures where
the photographer also wants to be in the shot. Use a tripod or
otherwise ensure that the camera is stable before using the self-timer.

1 Press the self-timer button “! ”. The “! ” icon appears


on the top display panel.

• The self-timer will not operate if the camera shutter cannot release, such
as when the camera cannot focus using AF (auto focus).
• If you are not using the M (manual) exposure mode to take the shot,
cover the eyepiece with your hand or with the eyepiece cap provided
(☞ P.73) before you press the shutter button to prevent interference to
achieve correct exposure from strey light.
• If you are using AF (auto focus) to focus the camera, take care not to
stand in front of the lens when you operate the self-timer.

2 Compose the shot, focus and then press the shutter


button.

• When the self-timer setting is “10 sec.”, the “!” icon flashes for 10
seconds on the top display panel when the self-timer starts running. The
self-timer lamp flashes for 8 seconds and then remains lit for the last 2
seconds before the shutter releases. If you have selected red-eye
reduction mode (☞ P.75), the self-timer lamp lights for the last 2 seconds
at the brightness used for red-eye reduction mode shooting.
• To cancel self-timer mode, press the self-timer button “!” again either
before or during self-timer operation, or switch the camera off. You can
also cancel self-timer mode by performing a camera reset (☞ P.56).

Downloaded from ManualsCamera.com Manuals


72
Diopter Adjustment Function/Eyepiece Cap

■ The diopter adjustment function makes it easier for you to check your
shots by looking at the image through the viewfinder.

• While you are looking through the viewfinder, slide the diopter
adjustment knob to the position in which you see the focusing frame in
the viewfinder most clearly. The setting can be adjusted between -1.5
and 1.0 dpt (near-sighted to far-sighted). Also, 9 types of Nikon diopter
adjustment lens are also available ranging from -5.0 to +3.0 dpt.

☞ Note
Points to watch when sliding the diopter adjustment knob
When you are sliding the diopter adjustment knob as you look through the
viewfinder, because your fingers are very close to your eye, take care not to
injure your eye with your fingertip or fingernail.

■ Attaching viewfinder accessories such as the eyepiece cap and diopter


adjustment lenses

• To attach the eyepiece cap or a diopter adjustment lens to the viewfinder


eyepiece, remove the eyepiece surround and fit the accessory onto the
viewfinder eyepiece starting from the top. To remove eyepiece cap or
diopter adjustment lens and re-attach the eyepiece surround, fit the
eyepiece surround so that the “Nikon DK-10 JAPAN” lettering on the
surround is on the lower edge.
3

Downloaded from ManualsCamera.com Manuals


73
Flash Photography

Built-in Flash and TTL-BL Flash Control


The built-in flash in the FinePix S1 Pro covers the field of view for a 28 mm
lens and has a guide number of 15 (ISO 100 • m). The flash also features TTL-
BL flash control that uses brightness information obtained using multi-pattern
exposure metering to effectively control and balance the amount of flash so
that both the main subject and the background are correctly exposed. This
allows you to take natural looking pictures using the flash (when a Nikkor lens
with built-in CPU is used). As well as in low-light conditions, you can use the
flash as a supplementary light source to reduce shadowing on your main
subject in outdoor shots taken in daylight or when you want to add catch lights
to your subject’s eyes.
The FinePix S1 Pro also provides 4 synchro modes: Normal synchro, red-eye
reduction, slow synchro and red-eye reduction slow synchro.
• When the lens used is not a Nikkor lens with built-in CPU, TTL flash control
is used in which allowance is not made for exposing the background.
(Wherever possible, use a Nikkor lens with a built-in CPU.)

Flash Control Range (Effective Flash range)


The flash control range (effective flash range) varies depending on the
selected ISO sensitivity and aperture settings. Refer to the table below for the
flash control range details when the built-in flash is used.

ISO 320 400


Guide number 27 30
f-stop (aperture) Flash control range Flash control range
2.8 2.2-10.3m 2.5-11.5m
(7.2 - 33.8 ft.) (8.2 - 37.7 ft.)
4 1.8-8.7m 2.0-9.7m
(5.9 - 28.5 ft.) (6.6 - 31.8 ft.)
5.6 1.3-6.3m 1.5-6.8m
(4.3 - 20.7 ft.) (4.9 - 22.3 ft.)
8 0.8-4.3m 1.0-4.8m
(2.6 - 14.1 ft.) (3.3 - 15.7 ft.)
11 0.8-3.2m 1.0-3.6m
(2.6 - 10.5 ft.) (3.3 - 11.8 ft.)

• If you are shooting at distances as close as 1 meter, select the aperture-


priority exposure mode (“A”) and use an f-stop of number of at least 8.
• When the sensitivity is set to ISO 800 or ISO 1600, the built-in flash will fire
but flash control may not be performed correctly.
Shoot in preview mode so that you can check the exposure.

Downloaded from ManualsCamera.com Manuals


74
Synchro Mode Types and Features
K: Red-eye reduction mode
If you select red-eye reduction mode and then
take a picture using the flash, the red-eye
reduction lamp lights for about 1 second
before the flash fires, thereby reducing the
tendency for people’s eyes to appear red in
pictures taken in low-light conditions.

L: Slow synchro mode


In flash photography, the shutter speed is
normally set automatically to 1/125 sec.
However, in slow synchro mode, a slower
shutter speed is used to allow the background
to be exposed also. This allows you to take
pictures that capture the full atmosphere of an
evening or night scene.

• You can set red-eye reduction mode and slow synchro mode concurrently by
selecting the modes so that red-eye reduction slow synchro mode icon “:”
appears in the top display panel.
• The synchro modes that can be set may vary depending on the exposure
mode. See “Combining Modes” on P.80 for information on the possible
combinations of synchro modes and exposure modes.

☞ Note
Notes on the Synchro Modes
• In red-eye reduction mode and slow synchro red-eye reduction mode,
because there is a 1 second delay for the red-eye reduction lamp to operate
before the flash fires, care must be taken that the subject does not move until
the shutter actually releases. (These modes should not be used in situations
such as snapshots where you need the camera to respond immediately.)
• Depending on which lens is mounted on the camera, the light from the red-
eye reduction lamp may be obstructed by the lens so that the effect of red-eye
reduction is lost for people in some positions in the shot.
• In slow synchro mode and slow synchro red-eye reduction mode, take care to
3
avoid camera shake since a slower than usual shutter speed is used. (A
tripod should be used.)

Downloaded from ManualsCamera.com Manuals


75
Flash Photography - continued

Taking Pictures Using the Built-in Flash

1 Press the flash lock release button so that the flash


pops up. Then hold down the synchro mode button “j ”
and turn the command dial to set the synchro mode.

• When the flash pops up, it starts charging. When charging is complete,
the Ready icon “j ” appears in the viewfinder display.
• When normal synchro mode “j ” is selected, the “j ” on the top display
panel disappears when you take your finger off the synchro mode button
“j ”.
• To stow the flash, push it down gently by hand.
• The built-in flash cannot be used when the battery adapter is used.

2 Set the exposure mode and check the shutter speed


and aperture setting.
• The table below shows the shutter speeds and aperture settings that can
be specified in each of the exposure modes.

Exposure Mode Valid Shutter Speeds Valid Apertures Ref. Page


AUTO mode ☞ P.60
Programmed auto Automatically set by ☞ P.61
the camera Automatically set by
5-vari program the camera ☞ P.66
Shutter-priority auto 1/125 to 30 sec. *1 ☞ P.62
Aperture-priority auto Automatically set by ☞ P.63
the camera Any aperture *2
Manual 1/125 to 30 sec. *1 ☞ P.64

*1: If a shutter speed faster than 1/125 sec. is selected, the shutter speed is
automatically reset to 1/125 sec. when the flash unit pops up. (When a Nikon
flash unit is used, the shutter speed is reset when you switch the flash unit on.)
*2: The flash control range is determined by the ISO sensitivity and aperture settings.
When you set the aperture in aperture-priority auto or manual mode, allow of the
flash control range shown on P.74.

Downloaded from ManualsCamera.com Manuals


76
3 Check that the Ready icon “j ” is displayed in the
viewfinder display and take the picture, taking care to
stay within the flash control range (☞P.74).
• If the Ready icon “j ” flashes for about 3 seconds after the shutter
release, the flash fired at full power and the image may be
underexposed. Recheck the distance to the subject, the aperture and the
flash control range and then try taking the picture again.
• If you are using AF (auto focus) and the subject is dimly lit, the AF
auxiliary lamp (☞ P.57) lights automatically to focus the camera.
• When the exposure mode is AUTO or programmed auto, the widest
aperture setting that can be automatically set by the camera varies
depending on selected ISO sensitivity. See P.79.

Flash Intensity
The intensity of the flash varies depending on the composition of the shot and
can detract from the intended exposure for the main subject. If this occurs,
take the shot using exposure compensation (☞ P.71).

Lenses that Can Be Used with the Built-in Flash


Nikkor lenses with built-in CPUs from 28 to 200 mm can be used with the built-
in flash.
• The AF 300 mm f/4 can be used.
• The AF-S 17-35 mm f/2.8 and AF 20-35 mm f/2.8 lenses cannot be used.
• Remove the lens food.
• Zoom lenses with macro settings cannot be used for macro photography.
• The table below lists the lenses on which vignetting occurs and reduces the
amount of light around the periphery of the image. Restrictions apply to the
focal lengths and distances at which these lenses can be used.

AF Zoom Lenses Affected Notes


by Vignetting
AF24-50mm f/3.3-4.5 Can be used at 35 mm or higher.
AF24-120mm f/3.5-5.6 Can be used at 35 mm for 1.5 m or higher and at 50-70 mm for 1 m or
more.
AF-S ED 28-70mm f/2.8 Can be used at 70 mm for 1.2 m or higher.
AF28-85mm f/3.5-4.5 Can be used at 35 mm for 1.5 m or higher.
AF28-200mm f/3.5-5.6 Can be used at 35 mm or higher.
AF35-70mm f/2.8 Can be used at 50 mm or higher. 3
AF70-180mm f/4.5-5.6 Can be used at 70 mm for 1.5 m or higher and at 85 mm for 1 m or
more.
AF-S ED 80-200mm f/2.8 Can be used at 105 mm or higher.
However, this lens cannot be used at 105 mm at 2 m or less.

Downloaded from ManualsCamera.com Manuals


77
Flash Photography - continued

Nikon Flash Units that Can Be Used


The table below shows the Nikon flash units that can be used with the FinePix
S1 Pro and the types of photography they can be used for. (Note that the built-
in flash and a Nikon flash unit cannot be used together.) This explanation
assumes that the lens mounted on the camera is a Nikkor lens with a built-in
CPU. (Lenses other than Nikkor lenses with a built-in CPU should not be
used.)

Available Photography TTL-BL flash Automatic


Modes control external Manual Multi-flash Slave flash
Flash Model (*1) flash control
SB-28 A A A A —
SB-27 A A A — —
SB-26 A A A A A
SB-25
A A A A —
SB-24
SB-23
A — A — —
SB-21B (*2)
SB-22
SB-22s
SB-20 A A A — —
SB-16B
SB-15
SB-11 (*3)
SB-14 (*3)
A A A — —
SB-140 (visible
light)(*3)

A: Usable
—: Not usable

*1: If the exposure mode is set to Manual, simple TTL-BL flash control (☞ P.74) is
used.
*2: When the SB-21B is used, auto focus can only be used to take pictures when
the AF micro lens (60, 105, 200 or 70-180 mm) is mounted on the camera.
*3: If TTL mode is used with the SB-11, SB-14 or SB-140, the flash unit must be
connected using the Nikon SC-23 TTL flash control cord.
If these flash units are used in A mode or M mode, the Nikon Sensor Unit SU-2
is used with the SC-13 for the SB-11 and SB-14, and the Nikon Sensor Unit
SU-3 is used with the SC-13 for the SB-140. Alternatively, the SC-11 or SC-15
can be connected with the Nikon Sync Terminal Adapter AS-15.

● For details, refer to the instructions provided with your flash unit.
If your Nikon flash unit has instructions which include a table of camera types
and it is capable of TTL mode, refer to the section for D group cameras.
Downloaded from ManualsCamera.com Manuals
78
Notes on Using Nikon Flash Units
● The synchronized shutter speeds when using the flash are 1/125 sec. and
slower.
In TTL mode, the ISO sensitivity linked settings are ISO 320 or ISO 400.
* When the sensitivity is set to ISO 800 or ISO 1600, the TTL flash control may not be
performed correctly.

● Red-eye reduction is performed using the red-eye reduction lamp on the


camera.
● If the Nikon flash unit is equipped with an active auxiliary flash function, the
active auxiliary flash on the flash unit automatically fires instead of the
auxiliary AF light on the camera. However, if the selected mode is not TTL,
the auxiliary AF light on the camera automatically lights.
● To use the flash to take pictures in modes other than TTL, set the exposure
mode to A or M.
● When the exposure mode is set to AUTO or P, the widest aperture setting
that can be automatically set by the camera is controlled by the selected
sensitivity, as shown in the table below.

Selected Sensitivity (ISO) 320 400


Widest aperture setting (built-in flash) 4 4
Widest aperture setting (Nikon flash) 5.6 5.6

* If the widest aperture is darker than the aperture setting permitted by the sensitivity, the
aperture is determined by the widest f-stop setting for the lens mounted on the camera.

● For close-up or wide-angle photography, a flash unit with automatic external


flash control should be used.
● When a synchro terminal is required, use the Nikon Sync Terminal Adapter
AS-15 (sold separately).
● Do not use flash units not manufactured by Nikon (flash units that apply 250
V or more to the X contact on the camera or that make contact at multiple
points on the small contacts on the accessory shoe). This could not only
result in camera malfunctions but could also damage the synchronizing
circuits in the camera and the flash.

Downloaded from ManualsCamera.com Manuals


79
Combining Modes

■ The table below shows the permitted combinations of exposure modes


and functions. This explanation is based on the FinePix S1 Pro used
with an AF Nikkor lens (excluding the AF-S, AF-I, IX Nikkor and F3AF
lenses).
Function AF Auxiliary Program Exposure Metering Normal Red-eye Red-eye Slow
mode AF light shift compen- mode (*1) synchro reduction reduction synchro
sation slow
synchro
Exposure Mode P.57 P.57 P.61 P.71 P.69 P.76 P.75 P.75 P.75
z AUTO AF-A A — — Multi-pattern B A — —
P Programmed AF-A A A A Multi-pattern A A A A
auto
S Shutter- AF-A A — A Multi-pattern A A — —
priority auto
A Aperture- AF-A A — A Multi-pattern A A A A
priority auto
M Manual (*2) AF-A A — A Center-weighted A A — —
x Portrait AF-A A — — Multi-pattern B A — —
c Landscape AF-A — — — Multi-pattern B A — —
v Close-up AF-A A — — Multi-pattern B A — —
b Sport AF-C — — — Multi-pattern B A — —
n Night scene AF-A A — — Multi-pattern — — A B

AF-A: Auto AF servo


AF-C: Continuous AF servo
A: Can be set.
B: This mode is automatically set when you set the exposure mode. (However,
other synchro modes can be selected.)
—: Cannot be set.
*1: Whichever exposure mode is set, center-weighted exposure metering is
selected when AE lock is used (☞ P.70).
*2: If the lens mounted on the camera is not a Nikkor lens with a built-in CPU,
pictures can only be taken in the M (manual) exposure mode. However, the
camera’s exposure meter cannot be used and the aperture cannot be set using
the aperture button and command dial. (Use the aperture ring on the lens to set
the aperture.) See also “Lenses that Can Be Used with this Camera” on P.106.
● The synchro modes are controlled by the TTL-BL flash control (☞ P.74), but if
the exposure mode is set to M (manual), simplified TTL-BL flash control is used
in which only approximate allowance is made for background exposure.

Downloaded from ManualsCamera.com Manuals


80
Shooting and Recording Previews
■ This section describes how to display a preview image of the shot you
have taken on the color LCD monitor and then record that image.

☞ Note
Preview Setup
In order to display a preview image and then record or erase the image, you
must first set the “PREVIEW” setting to “MANUAL REC”, as described in
“Preview” (☞P.49) in Setup. This function will not work if any other setting is
selected. Also, to record the image in this mode, you must take the steps
described below after taking the shot.

1 Take a picture in the normal way.

2 To record the image displayed on the preview screen,


press function button [1] or press the “MENU/EXE”
button.
If you do not take this step, the image is not recorded.

If you do not want to record the image, press function


button [2] or press the “CANCEL” button, or press the
shutter button halfway (the image is cleared from the
preview screen).
3

Downloaded from ManualsCamera.com Manuals


81
Standard Chart Display
■ Standard chart display is a feature that allows you to check the color
tones and brightness of a photographed image by comparing the
preview image with a color bar or grayscale indicator.

1 Display the preview image (☞P.49, 81).

2 Press function button [4] to display the Standard chart.

• You can clear the display by pressing function button [4] again.

Downloaded from ManualsCamera.com Manuals


82
Histogram Display
■ A histogram is a graph that classifies the light and dark portions of an
image and shows the statistical distribution of brightness in that image.
This section describes how to display the histogram for an image.
Histograms can be displayed for both playback images and preview
images.
■ To view the preview image histogram

1 Display the preview image (☞P.49, 81).

2 Press function button [3] to select the histogram you


want to view.

“Brightness”
• The histogram icon displayed on the rear display panel changes in the
cycle shown below each time function button [3] is pressed.

: Image histogram not shown.

: Image histogram for brightness shown.

: Image histogram for red shown.

: Image histogram for green shown.

: Image histogram for blue shown.

• The same procedure can be used when you are viewing a playback
image. In that situation, press function button [1]. 3

Downloaded from ManualsCamera.com Manuals


83
Multi-exposure
■ Multi-exposure is photography method in which other images can be
overlaid on top of an existing image. Any number of images can be
overlaid in this way.

☞ Note
Multi-exposure Setup
To use multi-exposure photography, you must first set the multi-exposure
setting to “ON” as described in “Setting Multi-exposure” in Setup (☞P.48). If
“OFF” is selected, this function will not work. Note that if multi-exposure is set
to “ON”, the preview image is displayed on the color LCD monitor regardless of
whether the “PREVIEW” setting is selected in the “SET-UP” menu.

1 Take a picture in the normal way.


• The preview image is displayed.

2 Press function button [2].

3 Locate the image to be overlaid in the viewfinder and


press the shutter button fully.
• You can overlay any number of images by repeating steps 2 and 3.
• If you do not want to overlay an image onto the photographed image,
locate the subject in the viewfinder and press the shutter button down
fully without pressing function button [2].

4 To record the overlaid images, press function button [1]


or press the “MENU/EXE” button.

• If you do not want to record the image, press function button [3] or press
Downloaded from ManualsCamera.com
the “CANCEL” button. Manuals
84
4 Advanced Photography
(Playback) Playback Functions
Functions available from the rear display panel
• Functions that can be used with images played back
Ref.
Function Description
Page
Histogram display Classifies light and dark areas in the image and ☞ P.83
displays their statistical distribution.
Erase frame Erases the displayed image. ☞ P.35
Protect frame setting Protects the displayed image to prevent accidental ☞ P.88
erasing.
DPOF frame setting Sets DPOF information for the displayed image. ☞ P.93
Playback zoom Displays the current image enlarged. ☞ P.32

Functions available from the playback menus on the color LCD monitor
• Functions that can be used by pressing the “MENU/EXE” button when the
image is displayed on the color LCD monitor

Ref.
Function Description
Page
ERASE/FORMAT Can be used to erase all the images on a media or ☞P.86
format the media.
MULTI PLAY setting Can be used to set the number of images displayed ☞P.33
when multiple frames are displayed on the color LCD
monitor.
PROTECT setting Protects all the images to prevent accidental erasing. ☞P.89
DPOF settings Can be used to set DPOF information for all the images ☞P.91
and to display only those images for which DPOF
information is set and then delete the settings. When
the images are printed, these settings can specify that
the date and time of shooting are also shown.
AUTO PLAY setting Can be used to specify sequential playback of the ☞P.101
recorded images.
Color LCD monitor Adjusts the brightness of the color LCD monitor. ☞P.103
BRIGHTNESS
adjustment

Downloaded from ManualsCamera.com Manuals


85
Erase/Format

Erase All/Format
When you select the Erase All option, all the unprotected images are erased. If
you select the Format option, all the images are erased, including any
protected images, and the media is initialized for the FinePix S1 Pro.
To erase only one of the recorded images, see P.35.

1 On the rear display panel, check the media type from


which the images are to be erased.

For a “SmartMedia”
• To select a different media type, select “MEDIA” in the “SET-UP” menu
(☞ P.51).

2 Press the “PLAY” button to display the image.

3 Press the “MENU/EXE” button to display the “ERASE”


menu.

To erase all the unprotected frames, use “a” or “b ” on


4 the 4-direction button to select “ALL”. To format the
media, select “FORMAT”.

Downloaded from ManualsCamera.com Manuals


86
5 Press the “MENU/EXE” button and then select “YES” to
execute “(ERASE) ALL” or “FORMAT”.
• To cancel the procedure, use “a” or “ b ” on the 4-direction button to
select “NO” and then press the “MENU/EXE” button.

6 Press the “MENU/EXE” button.


The “(ERASE) ALL” or “FORMAT” procedure ends and
the “NO IMAGES” message is displayed. Press the
“PLAY” button or press the shutter button down
halfway to return to photography mode.
• If you try to erase all the images when DPOF settings have been
specified for any of the images, an erase confirmation message appears.
Check the images and then press the “MENU/EXE” button.

Downloaded from ManualsCamera.com Manuals


87
Protection Settings

Protecting and Unprotecting Individual Image


Press the “PLAY” button and then press “d” or “c” on
1 the 4-direction button to display the image for which
you want to set or remove the protection.

2 Press function button [3].

With the Protection setting set to “OFF”

3 Press function button [1].

• When you press function button [1], protection is specified for the
selected image.
• A key icon appears in the top-right corner of the protected images.
• To protect another image, use “d” or “ c ” on the 4-direction button to
select the image.
• To cancel the procedure, press the “CANCEL” button.
• When you press function button [4], protection is removed from the
selected image.

Downloaded from ManualsCamera.com Manuals


88
Protecting and Unprotecting All Images
Use this setting to prevent images from being accidentally erased.
This procedure can be used to set the protect attribute for all the images on the
media.

1 On the rear display panel, check the media type


containing the images for which protection is to be set
or removed.

For a “SmartMedia”
• To select a different media type, select “MEDIA” in the “SET-UP” menu
(☞P.51).

2 Press the “PLAY” button to display the image.

3 Press the “MENU/EXE” button to display the menu.

Press “d” or “c” on the 4-direction button to display


4 the “PROTECT” menu.

Downloaded from ManualsCamera.com Manuals


89
Protection Settings - continued

Press “a” or “b ” on the 4-direction button to select


5 “ALL” if you want to protect the images or
“UNPROTECT ALL” if you want to remove the
protection and then press the “MENU/EXE” button.

“ALL” is selected

6 Check the confirmation message and then press the


“MENU/EXE” button.

Set protection
• When you press the “MENU/EXE” button, protection is either set or
removed for all the images.
• To cancel the procedure, press the “CANCEL” button.
• A key icon appears in the top-right corner of the protected images.

Downloaded from ManualsCamera.com Manuals


90
DPOF Settings

DPOF
DPOF stands for Digital Print Order Format and refers to a format that is used
for recording print specifications for images shot using a digital camera on a
SmartMedia or Microdrive/CompactFlash. The recorded print specifications
include the image that are to be printed and the number of prints of each
image.

SmartMedia
DPOF compatible printer
DPOF file
• Image file specification
Digital camera • Number of prints specification

Image file Image file Image file


(1) (2) (3)

• On a DPOF-compatible digital camera (the FinePix S1 Pro), the above


information can be recorded onto a SmartMedia or Microdrive/CompactFlash
using the camera controls.
• If DPOF information is recorded on the media, the specified number of prints
of the specified frames (image files) can also be printed on a DPOF-
compatible printer.

Downloaded from ManualsCamera.com Manuals


91
DPOF Settings - continued

Setting or Cancelling Date/Time Imprinting


Use the procedure below to specify whether the date and time of shooting are
included on the image prints.

1 Press the “PLAY” button and then the “MENU/EXE”


button to display the menu.

Press “d” or “c” on the 4-direction button to display


2 the “DPOF” menu.

Press “a” or “b ” on the 4-direction button to select


3 “DATE OFF”.

Downloaded from ManualsCamera.com Manuals


92
Press “d” or “c” on the 4-direction button to select
4 either “DATE ON” or “DATE OFF”. The selected setting
then remains valid for all images until the camera is
switched off.

• Pressing the “CANCEL” button clears the menu display.


• Always specify “DATE ON” or “DATE OFF” before specifying other DPOF
settings.

Specifying DPOF Settings for Single Frame


Use the procedure below to specify DPOF settings (specify the number of
prints) for the selected image.

Press the “PLAY” button and then press “d” or “c” on


1 the 4-direction button to display the image for which
you want to specify the DPOF settings.

2 Press function button [4].

Downloaded from ManualsCamera.com Manuals


93
DPOF Settings - continued

3 Press function button [1] or [3] to specify the number of


prints for the image.

• Press function button [1] to increase the number of prints and function
button [3] to decrease the number of prints.

■ To specify trimming (steps 4 to 5)

Press “a” on the 4-direction button. The trimming


4 settings screen appears. Press “a” on the 4-direction
button to further enlarge the image.

• Press “ b ” on the 4-direction button to return the enlarged image to its


original size.
• Press “d” or “ c ” on the 4-direction button to display (play back) another
image.
• Press the “CANCEL” button to return to normal image display.

5 If you want to trim another part of the image, press the


“PLAY” button to display the cursor and then use “a”,
“ b ”, “d” and “c” on the 4-direction button to display
the part of the image you want to trim.
• The table below lists the magnifications at which trimming can be
performed.

Image Size Magnification


3040 × 2016 4.52×
2304 × 1536 3.6×

Downloaded × 960ManualsCamera.com
1440from 2.14× Manuals
94
• To cancel the cursor and return to the normal enlarged display screen,
press the “PLAY” button again or press the “CANCEL” button.

6 Press function button [4].

• Pressing function button [4] sets the DPOF information.


• To cancel the procedure, press the “CANCEL” button.

Checking and Cancelling DPOF Settings for Single Frame


(REVIEW/CANCEL)
You can use the procedure below to display only images for which DPOF
settings are specified and then cancel the settings for each image.

1 Press the “PLAY” button to display the image.

2 Press the “MENU/EXE” button to display the menu.

Press “d” or “c ” on the 4-direction button to display


3 the “DPOF” menu.

Downloaded from ManualsCamera.com Manuals


95
DPOF Settings - continued

Press “a” or “ b ” on the 4-direction button to select


4 “REVIEW/CANCEL”.

5 Press the “MENU/EXE” button.

6 You can check only the frames for which prints are
specified by pressing “d” or “c” on the 4-direction
button. To cancel the DPOF settings, display the image
and then press the “MENU/EXE” button.

• If there are no images with DPOF settings, no images are displayed.


• Images are arranged in the order in which the DPOF settings were
specified.
• If an image with DPOF settings contains an error or if the DPOF settings
were specified on a different device, a confirmation message appears.
Check the message and then press the “MENU/EXE” button to cancel the
settings or the “CANCEL” button to cancel the procedure.
• Pressing the “MENU/EXE” button cancels the DPOF settings for the
specified image.
• To cancel the procedure, press the “CANCEL” button.

Downloaded from ManualsCamera.com Manuals


96
Setting DPOF Settings for All the Images (SET ALL)
Use the procedure below to set DPOF information for all the images on a
media.

1 Use the rear display panel to check the media type on


which you want to store DPOF information.

2 Press the “PLAY” button and then the “MENU/EXE”


button to display the menu.

Press “d” or “c” on the 4-direction button to display


3 the “DPOF” menu.

Press “a” or “ b ” on the 4-direction button to select


4 “SET ALL”.

4
5 Press the “MENU/EXE” button.

Downloaded from ManualsCamera.com Manuals


97
DPOF Settings - continued

6 Check the number of stored DPOF prints and then


press the “MENU/EXE” button.

• The total number of prints appears on the color LCD monitor and the
display then reverts to the menu screen.
• If an image for which DPOF settings are specified is damaged or if DPOF
settings were specified on a different device, the error tone sounds and a
confirmation message appears. Check the message and then press
“MENU/EXE” button to reset the DPOF settings or press the “CANCEL”
button to cancel the procedure.
• To cancel the procedure, press the “CANCEL” button.

Downloaded from ManualsCamera.com Manuals


98
Cancelling DPOF Settings for All Frames (CANCEL ALL)
Use the procedure below to cancel the DPOF information for all the images on
the media.

1 Use the rear display panel to check the media type on


which you want to cancel the DPOF information.

2 Press the “PLAY” button and then the “MENU/EXE”


button to display the menu.

Press “d” or “c” on the 4-direction button to display


3 the “DPOF” menu.

Press “a” or “ b ” on the 4-direction button to select


4 “CANCEL ALL”.

4
5 Press the “MENU/EXE” button.

Downloaded from ManualsCamera.com Manuals


99
DPOF Settings - continued

6 Check the number of prints for which DPOF settings


are to be canceled and then press the “MENU/EXE”
button.

• To cancel the procedure, press the “CANCEL” button.

Downloaded from ManualsCamera.com Manuals


100
Auto Play (Automatic Playback)

Auto Play Settings


Use the procedure below to select the Auto Play (automatic playback) method
for photographed images.
The Auto Play settings are as follows:
WIPE-OFF: Images are displayed without scrolling.
WIPE-1: Images are switched (wiped) on an angle.
WIPE-2: Images are switched (wiped) in a swirling pattern.
WIPE-3: Images are switched (wiped) in a mosaic pattern.
Display time: Display times of 0.3, 1, 2, 3, or 5 seconds can be selected.
• The display times are provided as a guide only. Actual times will vary
depending on factors such as the quality and image size settings for the
image. (Higher image quality settings and larger file sizes take longer.)

1 Press the “PLAY” button to display the image.

2 Press the “MENU/EXE” button to display the menu.

Press “d” or “c” on the 4-direction button to display


3 the “AUTO PLAY” menu.

Downloaded from ManualsCamera.com Manuals


101
Auto Play (Automatic Playback) - continued

Press “a” or “ b ” on the 4-direction button to select the


4 Auto Play time setting and then press “d” or “c” to set
the time. Then press “a” or “ b ” on the 4-direction
button to set the Auto Play method.

5 Press the “MENU/EXE” button.


Automatic playback begins.
• Automatic playback does not begin until you set the Auto Play method.
• To cancel automatic playback, press the “CANCEL” button.

Downloaded from ManualsCamera.com Manuals


102
Adjusting the Color LCD Monitor Brightness
■ The brightness of the color LCD monitor can be adjusted through 11
levels.

1 Press the “PLAY” button and then the “MENU/EXE”


button to display the menu.

Press “d” or “c” on the 4-direction button to display


2 the “BRIGHTNESS” menu.

• To cancel the procedure, press the “CANCEL” button.

3 Press the “MENU/EXE” button.

Downloaded from ManualsCamera.com Manuals


103
Adjusting the Color LCD Monitor Brightness - continued

Press “d” or “c” on the 4-direction button to adjust the


4 brightness.

• Press “ c” on the 4-direction button to increase the brightness of the color


LCD monitor and “d” to decrease the brightness.
• To cancel the procedure, press the “CANCEL” button.

5 Press the “MENU/EXE” button to confirm the setting.

• Pressing the “CANCEL” button clears the menu display.

Downloaded from ManualsCamera.com Manuals


104
5 Reference
System Expansion Options
■ By using the FinePix S1 Pro together with other optional FUJIFILM
products, your system can be expanded to fill a wide range of uses.
See pages 108-109 and 111-112 for details.

Digital Camera
FinePix S1 Pro <Image Input/Output to a Personal Computer>
USB Cable and Software
Image DIGITAL output (USB connection)
output
Floppy Disk Adapter (FlashPath)
(Floppy disk drive)

Image Memory Card Reader


(USB connection)
TV*
PC Card Reader
PC card adapter CR-500
SmartMedia Personal computer*
PC CARD
ADAPTER
(SCSI connection)
(PC card slot)
Image Memory Card Reader
(IEEE 1394 connection)

Microdrive/ Card adapter (PC card slot)*


CompactFlash*
Video output

Printer*
<Printing> Digital photo printer
FinePix Printer NX-500

* commercially available

5
Downloaded from ManualsCamera.com Manuals
105
Lenses that Can Be Used with this Camera

■ Use Nikkor lenses with built-in CPUs (excluding the IX Nikkor lenses)
with this camera. In particular, the full range of functions can be
accessed when a D-type AF Nikkor lens is mounted on the camera.

There are CPU signal Distinguishing feature of


contacts on Nikkor lenses D-type AF Nikkor lenses
with a built-in CPU.

When lenses other than Nikkor lenses with a built-in CPU are mounted
on the camera
• Restrictions apply to the exposure modes that can be used.
Lenses other than Nikkor lenses with a built-in CPU can only be mounted on
the camera and used to take pictures when the exposure mode is set to M
(manual). (In other modes, the shutter will not release.) However, the
camera's exposure meter cannot be used and the aperture cannot be set
using the aperture button and command dial. The “°” warning appears in
the aperture display on the top display panel and in the viewfinder display.
Use the aperture ring on the lens to check and set the aperture.

☞ Note
Lenses other than Nikkor lenses with a built-in CPU that cannot be used
The lenses other than Nikkor lenses with a built-in CPU listed below cannot be
used with this camera. Any attempt to forcibly mount one of these lenses on
the camera could damage the camera and lens.
• AF Teleconverter TC-16AS
• Non-Ai Nikkor lenses (lens types with a connecting bayonet that precede the
Ai system)
• Lenses that require the Focusing Unit AU-1 (400 mm f/4.5 and 600 mm f/5.6)
• Fish-eye lenses (6 mm f/5.6 and OP 10 mm f/5.6)
• ED 180-600 mm f/8 (product no. 174166 and earlier)
• ED 360-1200 mm f/11 (product no. 174087 and earlier)
• 200-600 mm f/9.5 (product no. 300490 and earlier)
• For F3AF (80 mm f/2.8 and 200 mm f/3.5, Teleconverter TC-16S)
• PC28 mm f/4 (product no. 180900 and earlier)
• PC35 mm f/2.8 (product no. 906200 and earlier)
• Reflex 1000 mm f/11 (product no. 142361-143000)
• Reflex 2000 mm f/11 (product no. 200310 and earlier)
• Medical Nikkor 200 mm f/5.6 (This lens can be used if used together with the
Sync Terminal Adapter AS-15.)
Downloaded from ManualsCamera.com Manuals
106
Types of Nikkor Lenses with a Built-in CPU and Other Lenses that Can Be Used

Modes Focusing Mode Exposure Mode Metering Mode


Multi-pattern metering Center-
Auto Focus
Manual Other M 3D weighted
focus aids
Lenses 6-zone 6-zone metering*1

D-type AF lenses r r r r r r — r
Nikkor lenses with a built-in CPU *2

AF-S, AF-I lenses — r r r r r — r


(D-type lenses)

PC micro 85 mm f/2.8D — r*4 r — r r — r


*3

AF-I Teleconverter — r*5 r r r r — r

AF Nikkor lenses other


than D-type (excluding r r r r r — r r
lenses for F3AF)
Ai-P Nikkor — r*6 r r r — r r
Lenses other than Nikkor lenses with a built-in CPU *7

Ai-S, Ai series E lenses, — r*6 r — t*8 — — —


modified Ai Nikkor

Medical 120 mm f/4 — r r — t*8 — — —

Reflex lenses — — r — t*8 — — —

PC Nikkor — r*4 r — t*8 — — —

Ai-S, Ai Teleconverter — r*5 r — t*8 — — —

Bellows PB-6 (used with — r*5 r — t*8 — — —


K ring 1, 3, 4 or 5)

Auto close-up rings (PK- — r*5 r — t*8 — — —


11A, 12, 13 and PN-11)

r : Usable
t: Usable subject to conditions
—: Not usable
*1 When the M (manual) exposure setting or AE lock is used, the light metering
mode is automatically switched to center-weighted metering.
*2 IX Nikkor lenses cannot be mounted on this camera.
*3 The camera’s light metering modes and flash control functions do not operate
correctly when camera movements are performed (both shift and tilt) or when
the aperture is set to any setting other than fully open.
*4 Only possible when camera shift or tilt are not performed.
*5 Can only be used when the combined aperture value is f/5.6 or brighter.
*6 Can only be used when the widest aperture value is f/5.6 or brighter.
*7 Some lenses cannot be mounted on this camera (☞ P.106).
5
Downloaded from ManualsCamera.com
*8 Set the exposure mode to M. Note that the Manuals
exposure meter cannot be used. 107
Optional Accessories Guide

■ This section introduces some of the key products in the range of


optional accessories available for the FinePix S1 Pro. Many other
optional accessories are available to further expand your selection of
photographic options. Refer to the catalog for details.

● SmartMedia™
The following types of SmartMedia can be used with
the FinePix S1 Pro:
• MG-4S : 4 MB, 3.3 V • MG-32S : 32 MB, 3.3 V
• MG-8S : 8 MB, 3.3 V • MG-64S : 64 MB, 3.3 V
• MG-16S :16 MB, 3.3 V
* Some 3.3 V SmartMedia are labelled as “3V” or “ID” cards.

● AC Power Adapter AC-5VH


Use this adapter when you want to take pictures over an
extended period or when the camera is connected to your
personal computer.
Can be used with voltages of 100-240 V AC at 50/60 Hz.
* The shapes of the AC power and plug depends on the
country of use.

● FUJIFILM Rechargeable Battery 2HR-3UF


The 2HR-3UF includes 2 pieces of high-capacity AA-size
Nickel Metal Hydride (Ni-MH) batteries.

● FUJIFILM Rechargeable Battery 4KR-3UF


The 4KR-3UF includes 4 pieces of high-capacity AA-size Ni-
Cd batteries.

● FUJIFILM Battery charger with Battery BK-NH (220V AC only)


The BK-NH includes the quick battery charger BCH-NH and
2 Ni-MH batteries.
The BCH-NH can charge 2 Ni-MH batteries in approximately
110 minutes.
Up to 4 Ni-MH or Ni-Cd batteries can be charged
simultaneously.

Downloaded from ManualsCamera.com Manuals


108
● Floppy Disk Adapter (FlashPath)
This adapter is the same size and shape as a 3.5-inch floppy
disk. You can copy the images on a SmartMedia to your PC
simply by loading the SmartMedia into the floppy disk adapter
and then inserting the adapter into your floppy disk drive.
Compatible OS Compatible SmartMedia
FD-A1/A1S/A1N Windows95/98, 5V/3.3V, 2 MB to 32 MB
NT 4.0
FD-A2 Macintosh 5V/3.3V, 2 MB to 64 MB

● PC Card Adapter
The PC Card Adapter allows the SmartMedia to be used as a
PC Card Standard ATA-compliant (PCMCIA 2.1) PC card
(Type II).
PC CARD
• PC-AD2 : Compatible with SmartMedia of 5V/3.3V, 2MB to ADAPTER

8MB.
• PC-AD3 : Compatible with SmartMedia of 5V/3.3V, 2MB to
64MB.

● Image Memory Card Reader SM-R1/R2


The SM-R1/R2 allows images to very easily be read and
written from an image memory card (SmartMedia) to a
personal computer. Its USB interface provides high-speed
data transmission.
• Windows98, Windows 2000 Professional (SM-R2 only) or
Power Macintosh with USB interface.

● Image Memory Card Reader DM-R1


This device allows image data shot on the camera to be
handled in essentially the same way as files on an external
disk drive for a personal computer.
• IEEE 1394 interface
• Dual slot for SmartMedia and CompactFlash Type II
(Microdrive-compatible)

● Carrying Case LC-S1


This is a specially designed carrying case for the FinePix S1
Pro. This case holds the camera body, optional accessories
(battery charger, AC power adapter, etc.), the compact flash
unit and replacement lenses.

5
Downloaded from ManualsCamera.com Manuals
109
Explanation of Terms
AF/AE Lock: On the FinePix S1 Pro, pressing the shutter button halfway locks the
focus and exposure settings (AF/AE lock). If you want to focus on a
subject that is not centered in the frame or change the picture
composition after the exposure is set, you can obtain good results by
changing the composition after the AF and AE settings are locked.

Auto Power Off Function: If the camera is not used in any way for a set period, the Auto Power
Off function switches the camera off to prevent battery depletion and
to avoid wasting power when the camera is connected to the AC
power adapter. On this camera, the period can be set to either 2
minutes or 5 minutes.
• The Auto Power Off function does not operate during automatic
playback, when a USB connection is being used, or when the Auto
Power Off function is switched off during setup.

Color Temperature: There is a set relationship between the surface temperature of a


substance such as coal and the color of the reflected light.
Substances with low color temperatures reflect a reddish light, while
substances with high color temperatures reflect light in which blue
tones are stronger. The color of the light for these temperatures is
expressed as a color temperature (K = Kelvin). The light of the sun at
midday in a completely clear sky is taken to be 5500K.

EV: A number that denotes exposure. The EV is determined by the


brightness of the subject and sensitivity (speed) of the film or CCD.
The number is larger for bright subjects and smaller for dark
subjects. As the brightness of the subject changes, a digital camera
maintains the amount of light hitting the CCD at a constant level by
adjusting the aperture and shutter speed.
The EV number increases by 1 if the amount of light hitting the CCD
doubles and decreases by 1 if the amount of light halves.

JPEG: Acronym for the Joint Photographic Experts Group.


JPEG is a file format for the compression and storage of color
images. The compression ratio can be selected, but the higher the
compression ratio, the poorer the quality of the expanded (restored)
image.

TIFF-RGB: A format for saving image data in which a tag indicating the file
format is attached to each item of data. Files stored in this format can
be opened on a personal computer.

TIFF-YC: A storage format for image data. To open an image stored in this
format, an application that supports the TIFF-YC format is required.
We recommend the FUJIFILM USB Interface Set IF-UB/S1. The size
of TIFF-YC data is 2/3 that of TIFF-RGB data.

White Balance: Regardless of the type of lighting, the human eye adapts so that a
white object still looks white. On the other hand, devices such as
digital still cameras register a white subject as white by first adjusting
their internal color balance to match the color of the ambient light
around the subject. This adjustment process is referred to as
matching the white balance. A function that automatically matches
the white balance is called an automatic white balance function.

Downloaded from ManualsCamera.com Manuals


110
Using the USB Cable and Software Included
■ By connecting the camera to a personal computer with the cable
provided, you can download image data from the camera to the
computer. However, you cannot upload data from the computer to the
camera. You can also control the camera, specify the photography
settings and take pictures from the computer.

☞ Note
Notes on Using the USB Cable
On some large lenses, the way in which the lens tripod is attached may be
such that lens and tripod obstruct the USB cable and could cause USB cable
connection faults.

✎ Important
Compatible personal computers
PCs running Windows 2000 Professional, Windows 98 (including the Second
Edition) and Macintosh computers running Mac OS 8.5.1 to Mac OS 9.0 can
be used.
Note that the computer must be equipped with a USB port. (Operation is not
guaranteed on home-made personal computers.)

1 Load the Media (SmartMedia or Microdrive/


CompactFlash) into the camera (☞ P.24).
• When you control picture taking on the FinePix S1 Pro, it is not necessary
to load the media.

2 Switch the camera on, press the “MENU/EXE” button


and use the “a” or “ b ” button to set the camera to PC
mode.
• To control picture taking on the FinePix S1 Pro from your PC, select “PC
MODE c SHOOTING” and use the “Camera Shooting Software”
application.
• To download image data from the FinePix S1 Pro to your PC, select “PC
MODE c DOWNLOADING”.
• Refer to the User’s Guide (PDF File) included CD-ROM for information on
using the software.

When you have selected the mode, press “a” or “ b ” on


3 the 4-direction button to select “END” and then press
the “MENU/EXE” button.

5
Downloaded from ManualsCamera.com Manuals
111
Using the USB Cable and Software Included - continued

4 Plug the small plug on the cable provided into the


digital (USB) socket on the camera and then plug the
other end of the cable into the USB port on the
computer. When you switch on the computer, the
“ ” icon appears on the camera’s rear display panel.

• Use only the special cable provided.


• When the “!BUSY” message appears on the rear display panel, this
indicates that the camera is being accessed. Never open the slot cover or
disconnect the cable while the camera is being accessed. This can
prevent correct data downloading and cause camera malfunctions.

Downloading mode Shooting mode


■ Replacing Media (Downloading mode)
● On Windows 98
Check that the camera is not being accessed, switch the camera off and
replace the media.
● On Windows 2000 Professional
Check that the camera is not being accessed, click on the Eject button in the
taskbar, and then switch the camera off and replace the media.
● On a Macintosh
Drag the removable disk icon on the desktop to the Trash. Once the
“REMOVE OK” message has appeared on the rear display panel, switch the
camera off and replace the disk.

• If you open the slot cover without switching the camera off, the “‹” warning
appears on the top display panel. If this occurs, switch the camera off and
then on again.
• You should use the optional AC Power Adapter AC-5VH (sold separately) and
the battery adapter. Data cannot be downloaded if the power fails during
downloading.
• The Auto Power Off function does not operate when the camera is connected
to a PC.

Downloaded from ManualsCamera.com Manuals


112
Notes on Using the FinePix S1 Pro
■ Places to Avoid
Do not store or use the camera in the following types of locations:
● Very humid, dirty or dusty places
● In direct sunlight or in places subject to extreme temperature rises, such as in a closed
car in summer. Extremely cold places
● Places subject to strong vibrations
● Places affected by smoke or steam
● Places subject to strong magnetic fields (such as near motors, transformers or
magnets)
● For long periods in contact with chemicals such as pesticides or next to rubber or vinyl
products

■ Do not expose the camera to sand.


The FinePix S1 Pro is particularly adversely affected by sand. In sandy locations such as
beaches or deserts, or in locations where there is windborne sand, ensure that the
camera is not exposed to sand. This can cause faults that may be irreparable.

■ Notes on Condensation
If the camera is carried suddenly from a cold location into a warm place etc., water
droplets (condensation) may form on the inside of the camera or on the lens. When this
occurs, switch the camera off and wait until water droplets are goes off. Condensation
may also form on the SmartMedia or Microdrive/CompactFlash. In this event, remove the
SmartMedia or Microdrive/CompactFlash and wait a short time before using it again.

■ When the Camera is Unused for Long Periods


If you do not intend to use the camera for a long period, remove the batteries and any
SmartMedia or Microdrive/CompactFlash before storing the camera.

■ Cleaning Your Camera


● Use a blower brush remove dust from the lens, LCD color monitor and viewfinder and
then wipe lightly with a soft, dry cloth. If any soiling remains, apply a small amount of
lens cleaning liquid to a piece of a lens cleaning paper and wipe gently.
● Do not scrape the lens, LCD monitor or viewfinder with hard objects as the surface
scratches easily.
● Clean the body of the camera with a soft dry cloth. Do not use volatile substances
such as thinners, benzene or insecticide, as these may react with camera body and
cause degeneration or deformation or cause the coating to peel off.

■ Using the Camera Overseas


● When travelling overseas, do not place your camera in the check-in baggage.
Baggage handling at airports may subject baggage to violent shocks, and the camera
may be damaged internally even when no external damage is visible.

5
Downloaded from ManualsCamera.com Manuals
113
Cleaning the CCD
■ This camera is equipped with a CCD photosensitive element. This CCD
is located behind the shutter screen.
If dust or other soiling attaches to the surface of the CCD and pictures
are then taken, this soiling may appear as spots in the image,
depending on the camera settings and the type of subject. If this
occurs, the CCD must be cleaned. Because the surface of the CCD is
extremely fragile, wherever possible the camera should be returned to
an authorized FUJIFILM dealer for cleaning (for a charge).
Any repairs carried out by an authorized FUJIFILM service facility to
CCDs that were scratched or damaged during cleaning by the customer
will be charged to the customer. Note that such repairs will probably
involve replacing the CCD and will be expensive.
☞ Note
Dust inside the camera and on the surface of the CCD
• Before a FUJIFILM digital camera is shipped from the factory, it is carefully
checked for dust inside the camera and on the surface of the CCD to ensure
that it conforms to FUJIFILM standards.
• Bear in mind also that some types of soiling on the CCD surface cannot be
removed even by an authorized FUJIFILM service facility.
Should this occur, you can use features such as the despeckling function
provided in the image processing software to remedy the problem.

☞ Note
Preventing Soiling of the CCD
• Change the lens in an area free of soling and dust.
• While the lens is detached from the camera, always fit the camera body cap
provided onto the camera. Check that the body cap and lens are free of any
soiling or dust.

Downloaded from ManualsCamera.com Manuals


114
Determining Whether Cleaning is Required

1 Connect the AC power adapter (sold separately) and


load the battery adapter.
• During cleaning, always use the AC power adapter and battery adapter to
ensure that a power failure does not cause the mirror to drop down or the
shutter to close and damage the camera.

2 Remove the camera lens.

3 Set the exposure mode dial to M.

4 Hold down both the self-timer button “!” and the AE


lock button “AE-L” and switch the camera on.

5 Press the shutter button. The mirror swings up and the


shutter opens and remains open.

6 Hold the camera so that the light shines on the CCD


and check the CCD surface.
• If there is soiling on the CCD surface, contact an authorized FUJIFILM
dealer to request cleaning or clean the CCD yourself as described on the
next page.
• If there is no soiling on the CCD surface, proceed to step 3 in “Cleaning
the CCD” on the next page to drop the mirror back down. 5
Downloaded from ManualsCamera.com Manuals
115
Cleaning the CCD - continued

Cleaning the CCD

1 Perform steps 1 to 5 in “Determining whether cleaning


is required” to swing the mirror up.
• Never disconnect the AC power adapter during cleaning as this can result
in damage to the camera shutter.

2 Use a blower to remove any soiling on the CCD surface.

☞ Note
Points to Note when Cleaning the CCD
• Use a blower that does not have a brush attached. Using a blower brush to
clean soiling from the CCD can scratch the CCD surface.
• If there is soiling on the CCD that cannot be removed using a blower, such as
oil or fingermarks, take the camera to an authorized FUJIFILM dealer for
cleaning. Never attempt to clean the CCD by wiping it as the CCD is
extremely fragile.

3 Check that all the soiling has been removed and then
hold down both the self-timer button “!” and the AE
lock button “AE-L” as you switch the camera off. Then
disconnect the AC power adapter from the camera.
• When you switch the camera off, the mirror drops down and the shutter
closes at the same time. Ensure that your fingers are not caught inside
the camera.

Downloaded from ManualsCamera.com Manuals


116
Power Supply Notes

Batteries that Can Be Used


• Use AA-size nickel-metal hydride (Ni-MH), AA-size Ni-Cd or AA-size alkaline
batteries, CR123A lithium batteries and a CR2025 button cell with the FinePix
S1 Pro.
Do not use AA-size manganese or AA-size lithium batteries as these battery
types emit heat that can cause camera faults or malfunctions.
• The capacity of alkaline batteries varies depending on the brand. The life of
some batteries may be considerably shorter than others.

Notes on Handling the Batteries


Incorrect use or handling of batteries can cause them to leak fluid, emit heat,
emit sparks or burst. Observe the following precautions:
• Do not heat batteries or throw them into a fire.
• Do not allow metal objects such as pins to come into contact with the positive
+ and negative - poles on a battery and do not carry or store batteries with
metal objects such as necklaces or hairpins.
• Do not get water or seawater on batteries and keep the battery terminals dry.
• Do not attempt to deform, disassemble or modify a battery.
• Do not attempt to remove or damage the battery casing.
• Do not drop, strike or otherwise subject batteries to strong impacts.
• Do not use batteries that are leaking fluid, are deformed or discolored or are
in any other way abnormal.
• Do not store batteries in very warm or humid places.
• Store batteries out of the reach of small children.
• When loading the batteries into the camera, ensure that the positive + and
negative - poles are arranged as indicated.
• Do not use new batteries together with used batteries. (With rechargeable
batteries, do not use charged batteries together with discharged batteries.)
Do not use batteries of different types or brands together.
• Remove the batteries from the camera if it will not be used for a long period.
(If the button cell CR2025 battery is removed from the camera, the camera
settings will revert to the factory default values.)
• Some batteries may feel warm just after use. Switch the camera off and allow
the batteries to cool before removing them.
• When replacing the batteries, always fit new batteries of the same type. In the
case of alkaline, lithium CR123A and button cell CR2025 batteries, “new
batteries” denotes recently purchased, unused batteries. In the case of
rechargeable Ni-MH and Ni-Cd batteries, it denotes batteries that were
recently fully recharged at the same time.
• In cold locations (+10°C (+50°F) or colder), battery performance declines and
the time for which the batteries can be used decreases. Because this
tendency is particularly pronounced in alkaline and lithium batteries, warm the
batteries by placing them in a warm place such as your pocket before using
them. If you are using a heating pad, take care not to place the batteries
directly against the pad.
5
Downloaded from ManualsCamera.com Manuals
117
Power Supply Notes - continued

If any battery fluid at all leaks from the batteries, wipe the battery
compartment thoroughly and then load new batteries.
If battery fluid comes into contact with your hands or clothing, wash the
area thoroughly with running water. If the fluid gets into your eye, it could
cause blindness. Flush the affected eye with clean water and then seek
medical assistance.

● Disposing of batteries
Dispose of used batteries in accordance with your local waste disposal regulations.
● Notes on Using Small Rechargeable Batteries (Ni-MH/Ni-Cd)
• Charge AA-size Ni-MH and Ni-Cd batteries correctly using the Battery Charger (220V
AC only, sold separately).
• Do not use batteries other than those specified in the Battery Charger (220V AC only,
sold separately).
• Note that batteries may feel warm immediately after charging. This is normal.
• Ni-MH and Ni-Cd batteries are not charged when they are shipped. Always charge new
batteries before using them.
• Due to the mechanical characteristics of the camera, a very small amount of current
flows even when the camera is switched off. Take particular care with Ni-MH and Ni-Cd
batteries as they will become excessively discharged and may no longer function even
when charged if you leave them in the camera for a long period.
• Ni-MH and Ni-Cd batteries self-discharge when not used. Always recharge the batteries
before using them. If the time for which a battery can be used decreases markedly even
when if are correctly charged, this indicates that the battery has reached the end of its
effective life. Purchase a new battery.
• Soiling such as fingermarks or grease on the poles of Ni-MH batteries can significantly
reduce the number of shots that can be taken using the batteries. If this occurs, wipe
the poles carefully with a soft dry cloth and recharge the batteries once they have fully
discharged.

● Recycling Small Rechargeable Batteries


This symbol is the recycling symbol used for small rechargeable batteries (such as Ni-
MH and Ni-Cd batteries). Small rechargeable batteries use scarce and valuable
resources that only exist in small quantities and these metals can be recycled.
Recycling resources in this way helps to reduce waste and protect the environment.
Dispose of your used small rechargeable batteries by sticking insulating tape over the
metal terminals on the batteries and taking them to your local recycling facility for small
rechargeable batteries.

Notes on Using the AC Power Adapter (AC-5VH) (sold separately)


Use only the AC-5VH AC Power Adapter with your FinePix S1 Pro Digital
Camera. The use of an AC adapter other than the AC-5VH may result in
damage to your camera.
• Take care to ensure that the contact points on the AC power adapter do
not touch other metal objects as this can cause a short-circuit.
• Do not plug the AC power adapter into the camera when it is running on
batteries. Switch the camera off and then plug in the AC power adapter.
• Do not load batteries into the camera or replace the batteries when the camera is running on
the AC power adapter. Switch the camera off first.
Downloaded from ManualsCamera.com Manuals
118
Notes on Media
■ SmartMedia
SmartMedia are a new recording media developed specifically for use in digital cameras. Each
SmartMedia card contains a semiconductor memory chip (NAND-type flash memory) which is
used to record digital image data.
Because the data is recorded electrically, recorded data can be erased and re-recorded.
■ SmartMedia with ID
SmartMedia ID (SmartMedia with ID) are SmartMedia that have been assigned individual ID
numbers. SmartMedia ID cards can be used in devices with features that use IDs for
applications such as copyright protection. SmartMedia ID cards can be used on the FinePix S1
Pro in the same way as conventional SmartMedia cards.
■ Microdrive
Microdrive are the smallest and lightest hard disk drive and conform to the CF Type II extended
standard for CompactFlash. Because Microdrive can hold large numbers of recorded images
and represent a very low cost per megabyte, they allow more economical recording of high-
quality images.
■ Data Retention
In the following situations, recorded data may be erased (or corrupted). Fuji Photo Film Co.
Ltd. accepts no liability for any losses incurred as a result of data being erased or corrupted.
* If the media is used improperly by the customer or by a third party
* If the media is affected by static electricity or electrical interference
* If the media is removed or the device is switched off while data is being recorded onto or
erased from the media (including formatting)
* If the media is bent or dropped, or subjected to strong impacts.

Important data should be backed up on to another media (MO


disk, floppy disk, hard disk, etc.).

■ Notes on handling media (all types)


• When inserting the media, hold it straight as you slide it in.
• Never remove the media or switch the camera off during data recording, during data
erasing (formatting) or during frame advance when images are being played back. These
actions could result in damage to the media.
• Media are precision electronic devices. Do not bend, drop, or subject media to excessive
shocks.
• Do not use or store media in environments likely to be affected by strong static electricity,
electrical noise or magnetic fields.
• Do not use or store media in very hot, humid or corrosive environments.
■ Notes on handling SmartMedia
• Use only the SmartMedia specified for use with the FinePix S1 Pro. The use of other
SmartMedia could damage the camera.
• Take care not to touch the SmartMedia’s contact area (gold-colored area) or allow the area
to become soiled. Use a dry lint-free cloth to wipe away any soiling that does occur.
• To avoid damage caused by static electricity, always use the special static-free case
provided during transportation or storage. Keep the SmartMedia in a storage case if
available.
• Inserting a SmartMedia that is charged with static electricity into your camera may result in
a camera malfunction. If this occurs, switch the camera off and then on again.
5
Downloaded from ManualsCamera.com Manuals
119
Notes on Media - continued

• Do not carry SmartMedia in locations such as a trouser pocket. This could subject the
SmartMedia to excessive force when you sit down, thereby damaging the SmartMedia.
• The SmartMedia may feel warm when it is removed from the camera after being used for
an extended period. This is normal and does not indicate a fault.
• SmartMedia cards have a limited life. After a long period of use it will become impossible to
record new image data on the card. In this event, purchase a new card.
• Stick the enclosed index label onto the index area on the SmartMedia. Do not use third-
party labels on the SmartMedia as this can cause faults when the SmartMedia is inserted
or removed.
• Take care that index labels do not overlap into the write-protect area.
• If there is any initial product defect in SmartMedia as a result of manufacturing by
FUJIFILM, the same number of replacement cards will be provided free of charge.
FUJIFILM accepts no liability for faults attributable to other causes.
■ Notes on using Microdrive and CompactFlash
• Do not write on the media label.
• Do not peel off the media label.
• Do not stick another label onto a media.
• When carrying or storing a media, keep it in the protective case provided.
• Do not use media in CF Type II slots that do not have an eject function.
• Take care when handling media that have been used for long periods as they may become
hot.
• Do not place media close to strong magnets.
• Keep media dry.
• Do not apply excessive force to the media cover.
■ Notes on using media with a personal computer
• If you intend to take photos using a media that has been used on a personal computer, first
format the media on your camera.
• When you format a media in the camera and then photograph and record images, a folder
is automatically created on the media. Image data is then recorded in this folder.
• Do not change or delete the folder names or file names on the media from your PC as this
will make it impossible to use the media in your camera.
• Always use the camera to erase image data on a media.
• To edit image data, copy the image data to the computer’s hard disk and then edit the
copied data.

■ SmartMedia Specifications
Type Image memory card for digital cameras (SmartMedia)
Operating voltage 3.3 V
Operating conditions Temperature: 0°C to +40°C (+32°F to +104°F)
Humidity: 80% or less (no condensation)
Dimensions 37 × 45 × 0.76 mm (1.45 × 1.77 × 0.03 in.) (W × H × D)

Downloaded from ManualsCamera.com Manuals


120
Warning Displays

■ If a warning is displayed or flashes in the top display panel, viewfinder


display, rear display panel or color LCD monitor, check the points
described in the table below before requesting repairs.

Problem Ref.
Cause Solution
Top display panel Viewfinder display Page
The aperture ring on Set the aperture ring P.20
‡ ‡ the lens is not set to on the lens to the
(flashing) (flashing) the narrowest narrowest aperture.
aperture.

O The lithium batteries Replace the lithium P.17, 18


(flashing) are flat. batteries. P.22

O The lithium battery Have spare lithium P.22


(lit) charge is low. batteries ready.

The lens mounted is Use a Nikkor lens with P.20


not a Nikkor lens with built-in CPU (excluding P.106
° ° built-in CPU or no lens IX Nikkor lenses).
(flashing) (flashing) is mounted on the (Note that pictures can
(lit in M mode) (lit in M mode) camera. still be taken in M
mode.)

The slot cover was Switch the camera off, P.25


‹ opened during card close the slot cover, P.112
(lit) operation. switch the camera
back on and try again.

• The AA-size batteries Switch the camera off P.18


are low on charge or and replace the AA-
flat. size batteries or load
‹ • No AA-size batteries new AA-size batteries.
(lit) are loaded. Then switch the
camera back on and
try again.

The lithium batteries Switch the camera off P.17, 18


are low on charge or and replace the lithium
the camera batteries. Then switch
mechanism has the camera back on
stopped due to cold and try again.
and cannot take If this does not resolve
‹ pictures. the problem, set the
(flashing) focusing mode to M,
release the shutter and
briefly switch the
camera off.

5
Downloaded from ManualsCamera.com Manuals
121
Warning Displays - continued

Problem Ref.
Cause Solution
Top display panel Viewfinder display Page

u AF (auto focus) cannot Focus the camera in P.58


(flashing) focus the camera. manual (M) mode.

The subject is too • In S mode (shutter- P.62


bright and is beyond priority auto mode),
the camera’s control select a faster shutter
range. speed.
• In A mode (aperture- P.63
⁄ ⁄ priority auto mode),
(lit) (lit) select a higher
aperture number.
• In exposure modes P.60-
other than M, use an 66
ND (light volume
adjustment) filter.

The subject is too dark • In S mode (shutter- P.62


and is beyond the priority auto mode),
camera’s control select a slower
range. shutter speed.
• In A mode (aperture- P.63
¤ ¤ priority auto mode),
(lit) (lit) select a lower
aperture number.
• In exposure modes P.60-
other than M, use the 66
flash.

The subject is dark Use the built-in flash. P.76


j and the flash should
(flashing) be used.

This icon flashing for Recheck the distance P.74


about 3 seconds after to the subject, the
the flash fires indicates aperture setting and
j that the full flash the flash control range
(flashing) intensity was used and and then try again.
the image may be
underexposed.

In modes other than A Set the mode selector P.79


‹ and ‹ and and M, the mode to ¸ or set the
j j selector on a Nikon exposure mode to A or
(flashing) (flashing) flash unit is not set to M.
¸.

Downloaded from ManualsCamera.com Manuals


122
Problem Ref.
Cause Solution
Rear display panel Color LCD monitor Page
The AA-size batteries Replace the AA-size P.18
(blinking) are flat. batteries.

The AA-size batteries Have replacement AA- P.18


(lit) are low on charge. size batteries ready.

The data played back The image cannot be


! READ ERROR was not recorded played back.
correctly.

! CARD NOT The recording media is Format the recording P.86


not formatted media.
INITIALIZED
(initialized).

! CARD ERROR The card played back The data on the card
contains an error. cannot be played back.

! PROTECTED There is a write-protect Use a SmartMedia that P.24


sticker on the does not have a write-
CARD
SmartMedia. protect sticker.

An attempt was made Remove the protection. P.88


! PROTECT ! PROTECT to erase a protected
frame.

DPOF print When the image is P.91-


DPOF FRAME specifications are set deleted, the DPOF 100
ERASE OK? for the image to be settings are cancelled
erased. at the same time.

DPOF file contains an To create a new DPOF P.91-


RESET UNMATCHED error, or the DPOF file file and redo all the 100
DPOF OK? was specified on DPOF settings, press
another device. the “MENU/EXE”
button.

More than 1000 The maximum number


frames were specified of frames that can be
! DPOF FILE ERROR in the DPOF frame specified for printing
settings. on the same media is
999.

The built-in flash was The built-in flash


popped up even cannot be used when
though the battery the battery adapter is
adapter is used. used.

• The recording media • Format the recording


is not formatted media.
‹ (initialized).
• You are trying to • Data cannot be
record onto a faulty recorded onto faulty
media. media.
5
Downloaded from ManualsCamera.com Manuals
123
Troubleshooting

Problem Cause Solution

No power. • The batteries are flat. • Load new batteries.


• The AC power adapter plug has • Plug the adapter back in.
come out of the power outlet.
Power cuts out during • The batteries are flat. • Fit new batteries.
operation.
Battery runs out • You are using the camera in • Put the batteries in your pocket
quickly. extremely cold conditions. or another warm place to heat
them and then load them into
the camera just before you take
a picture.
• The terminals are soiled. • Wipe the battery terminals with
a clean, dry cloth.
• The batteries have reached the • Fit new batteries.
end of their effective lives.
The date and time • No button cell CR2025 batteries • Fit new batteries.
are reset when you are fitted.
replace the AA-size • The button cell CR2025 • Fit new replacement batteries.
batteries. batteries are depleted.
No photograph is • No media is loaded. • Load a media.
taken when the • The media is full and no further • Load a new media or erase
shutter button is data can be recorded. some frames.
pressed. • The SmartMedia is write- • Remove the write-protection.
protected.
• The media is not formatted. • Format the media.
• The SmartMedia contact • Clean the SmartMedia contact
surface (the gold-colored area) surface (the gold-colored area)
is soiled. with a clean dry cloth.
• The media is damaged. • Load a new media.
• The Auto Power Off function • Switch the camera on.
has switched the camera off.
• The batteries are flat. • Fit new batteries.
• The camera will not focus. • Set the focusing mode to
manual (M), focus on the
subject manually and take the
picture.
• You tried to take a picture using • Close the built-in flash and then
the built-in flash when you were take the picture.
also using the battery adapter.
• An error occurred. • Refer to the warning displays on
P.121, 122 and 123 and take
the appropriate action.
I can’t use the flash • The flash is set to Suppressed • The flash pops up.
to take pictures. Flash mode. (The flash is
closed.)
• You pressed the shutter button • Wait until charging is completed
while the flash was charging. before pressing the shutter
button.
• You are using the battery • Use lithium batteries.
adapter.

Downloaded from ManualsCamera.com Manuals


124
Problem Cause Solution

The playback image • The subject is too far away. • Move closer to the subject.
is too dark even • Something is obstructing the • Remove the lens hood.
though I used the flash.
flash.
The playback image • The lens is dirty. • Clean the lens.
is blurred. • The camera is not focused. • Focus the camera correctly
(☞ P.28).
I cannot format the • The SmartMedia or Microdrive • Remove the write-protection.
SmartMedia or is write-protected. (Peel off the write-protect
Microdrive. sticker.)
• The media is damaged. • Use a new media.
I cannot erase all the • The frame is protected. • Remove the frame protection.
frames.
Nothing happens • Camera malfunction. • Remove the power supply (the
when I use the batteries) and then reload them
camera switches and and try again.
dials. • The batteries are flat. • Fit new batteries.
No image appears on • There is no media loaded. • Insert a media that contains
the color LCD • There is no photography data some photography data.
monitor when I press recorded on the media.
the “PLAY” button.
There is no image on • The camera and TV are not • Connect the camera and TV
the TV screen. connected correctly. correctly.
• Set the TV input to “VIDEO”.

5
Downloaded from ManualsCamera.com Manuals
125
Specifications

Item Specifications
Type of camera Interchangeable-lens SLR-type digital camera
Recording media • Slot 1: SmartMedia (3.3 V)
• Slot 2: Microdrive and CompactFlash (CF type II)
Recording

Recording modes Design rule for Camera File System-compliant (Exif Ver.2.1 JPEG-
compatible, TIFF-RGB or TIFF-YC), DPOF-compatible
Recorded image sizes 3040 × 2016 (6.13 megapixels), 2304 × 1536 (3.54 megapixels)
and 1440 × 960 (1.38 megapixels)
23.3 × 15.6 mm Super CCD with primary color filter (total no. of pixels:
Imaging

Picture element
3.4 megapixels in an interwoven pattern)
Sensitivity Equivalent to ISO 320, 400, 800 or 1600
Exposure control Auto, P, S, A, M, Portrait, Landscape, Close-up, Sport and Night scene
Lens mount Nikon F mount
Interchangeable lenses See P. 106, 107.
Actual field of view Approx. 1.5× the rated focal length of the lens (for 35 mm camera
equivalent)
Viewfinder Eye-level optical type (coverage: approx. 90% vertical and approx.
93% horizontal)
Eyesight adjustment –1.5 to +1.0 dpt
Auto focus TTL phase detection with auxiliary AF lamp
Lens servo AF (single AF servo or continuous AF servo automatically selected
by the camera), M (manual)
Exposure metering modes 3D 6-zone multi-pattern metering, 6-zone multi-pattern metering
and Center-weighted metering
Shutter Electronically controlled descending-type focal-plane shutter
Shutter speeds 1/2000 to 30 sec.
Exposure compensation ±3 EV (in 1/3 EV step increments)
Camera

AE lock BV memory type using AE lock button (center-weighted metering)


Self-timer 2 seconds or 10 seconds
Synchro contacts X contacts only (semiconductor-type), synchronized with External
Flash at low shutter speeds of 1/125 sec. and slower.
Built-in flash Manual pop-up type. Guide No. 15 (ISO 100 • m)
Illumination angle covers 28-mm lens field of view, TTL-BL flash control
F2.8 F4.0 F5.6 F8 F11
ISO 320 2.2-10.3 m 1.8-8.7 m 1.3-6.3 m 0.8-4.3 m 0.8-3.2 m
(7.2-33.8 ft.) (5.9-28.5 ft.) (4.3-20.7 ft.) (2.6-14.1 ft.) (2.6-10.5 ft.)
ISO 400 2.2-11.5 m 2.0-9.7 m 1.5-6.8 m 1.0-4.8 m 1.0-3.6 m
(8.2-37.7 ft.) (6.6-31.8 ft.) (4.9-22.3 ft.) (3.3-15.7 ft.) (3.3-11.8 ft.)
ISO 800 Not supported *1
ISO 1600 Not supported *1
Synchro modes Normal synchro, Red-eye reduction, Red-eye reduction slow
synchro, Slow synchro
Accessory shoe Hot shoe (with flash contacts, TTL automatic flash control contacts
and ready light contacts)
With safety lock mechanism
Remote release Release socket on shutter button
*1 The flash does not operate correctly at ISO800 and ISO1600. Use Preview mode to check the exposure
Downloaded from ManualsCamera.com Manuals
when shooting at these film speeds.
126
Item Specifications
Information display Viewfinder display
Display

Top display panel


Rear display panel (backlit)
Color LCD monitor 2-inch 200,000-pixel low-temperature polysilicon TFT
Video out mini pin jack (3.5-mm dia.) (NTSC/PAL)
I/O sockets

Digital (USB) Data downloading to PC and taking pictures your PC


DC input Used to connect AC Power Adapter AC-5VH
Auto Power Off Off, 2 min. or 5 min. (disabled during auto playback and when the
camera operates connected to a PC)
Battery check • Battery checking performed on camera and at image processor
respectively. However, checking is performed on the camera
when the battery adapter is used.
• Check levels: 3 levels (full, flat and low)
If the battery capacity is insufficient in either the image processor
Main Functions

or camera, a warning is displayed for 3 seconds and then the


Auto Power Off function is triggered.
White balance AUTO, Sunny, Shade, Fluorescent 1, Fluorescent2, Fluorescent3,
Incandescent and Custom
Playback Single-frame, 4-frame, 9-frame, Playback zoom, Histogram and
Auto-play
Erase modes Format, All frames, Single frame
Image quality settings Color, Tone, Sharpness
Other DPOF, Multi-exposure, Frame no. memory, Custom WB setting,
Standard chart
Dimensions 148.5 × 125 × 79.5 mm (5.8 × 4.9 × 3.1in.) (excluding LCD screen
and attachments)
Mass (Weight) 800 g (28.2oz.) (body only, not including batteries)
Power Image 4 AA-size batteries (alkaline (provided),
supply processor Ni-MH (sold separately) or Ni-Cd (sold separately))
Special AC Power Adapter AC-5VH (sold separately)
CR2025 lithium button cell battery (supplied, for clock and settings
backup)
General

Camera 2 CR123A lithium batteries (provided)


Power also available from image processor using battery adapter.
However, the built-in flash cannot be used when the battery
adapter is used.
Number of shots using Approx. 650 (without previews, recorded on SmartMedia, built-in
batteries*2 flash off)
(with Ni-MH batteries (HR-3UF) used in image processor and
CR123A lithium batteries used in camera)
Operating conditions Temperature: 0°C to +40°C. (+32°F to +104°F) (Note that the
range for Microdrive is +5°C to +40°C (+41°F to +104°F).)
Humidity: 80% or less (no condensation)
Accessories See P.9.
*2 This is a guide to the number of consecutive shots that can be taken at normal temperatures. Actual numbers
may vary depending on the camera’s operating conditions and the amount of charge in the batteries.
5
Downloaded from ManualsCamera.com Manuals
127
Specifications - continued

• Design and specifications are subject to change without notice.


• The color LCD monitor on your digital camera is manufactured using advanced high-precision
technology. Even so, small bright points and anomalous colors (particularly around text) may
appear on the monitor. These are normal display characteristics and do not indicate a fault with
the monitor. This phenomenon will not appear on the recorded image.

Standard Number of Available Shots (Recorded Images)


The number of available shots varies slightly depending on the type of subject.
The actual number of available shots also varies more widely from the standard
number as the capacity of the media increases.
Image Size Media Hi(RGB) Hi(YC) Fine Normal Basic
3040 × 2016 Microdrive (340 MB) 19 29 144 305 741
SmartMedia (64 MB) 3 5 26 55 132
SmartMedia (32 MB) 1 2 12 27 66
SmartMedia (16 MB) 0 1 6 13 32
2304 × 1536 Microdrive (340 MB) 33 50 249 520 1249
SmartMedia (64 MB) 6 9 45 94 221
SmartMedia (32 MB) 3 4 22 47 110
SmartMedia (16 MB) 1 2 11 23 54
1440 × 960 Microdrive (340 MB) 84 126 502 972 1822
SmartMedia (64 MB) 15 23 90 172 331
SmartMedia (32 MB) 7 11 45 86 165
SmartMedia (16 MB) 3 5 22 42 82

Compatible Media
• This camera is guaranteed to operate with FUJIFILM SmartMedia.
• Although FUJIFILM has tested many major types of Microdrives and CompactFlash cards,
some media may not be compatible with this camera.
Compatible Media (As of July 2000)
Microdrive IBM: 340MB
CompactFlash Sandisk: SDCFB-16/32/40/48/64/98/128
Lexer Media: 4× type 8 MB to 80 MB
8× type 8 MB to 160 MB

Batteries Uses and Symptoms When Batteries are Depleted


Uses Symptoms When Depleted

AA-size Alkaline Image processing “‹” appears on the top display


batteries panel
Lithium batteries Power functions such as auto focus, The camera will not switch on.
CR123A aperture, mirror and shutter
operation, and charge the flash.
Button cell lithium Stores the time and other settingsWhen the AA-size batteries are
battery CR2025 removed for replacement, the time
and other settings revert to the
Downloaded from ManualsCamera.com Manuals
factory default settings.
128
Safety Notes

■ The warning and attention symbols shown below are used to indicate the
severity of the injury or damage that will result if the indicated information
is ignored and the product is used incorrectly as a result.
Indicates information which, if ignored, could cause death or
WARNING
serious injury.

Indicates information which, if ignored, could result in


ATTENTION
personal injury or physical damage.

■ The icons shown below indicate types of information that should be


observed.

Indicates important information which the user should bear in mind.

Indicates a forbidden action.

Indicates a mandatory action that the user must perform.

WARNING
When an abnormal event occurs, switch the camera off and remove
the batteries or disconnect the AC power adapter.
Continued use of the camera when an abnormal event occurs, such as the
camera emitting smoke or an unusual oder, can cause a fire or electric shock.
Unplug from • Contact an authorized FUJIFILM dealer.
power socket

Do not allow water or foreign objects to enter the camera.


If water or any foreign object gets into the camera, switch the camera off,
remove the batteries and disconnect the AC power adapter.
Continued use of the camera can cause a fire or electric shock.
• Contact an authorized FUJIFILM dealer.

Do not put the camera down on an unstable surface.


The camera could tip over and fall, resulting in an injury.

Never attempt to disassemble or modify this camera. (Never open


the camera casing.)
Do not use the camera when you have dropped the camera or the
casing is damaged.
Do not Any of these actions can cause a fire or electric shock.
disassemble • Contact an authorized FUJIFILM dealer.

5
Downloaded from ManualsCamera.com Manuals
129
Safety Notes - continued

WARNING
Do not use this camera in a bathroom or shower.
This can cause a fire or electric shock.
Do not use
in a bathroom or
shower

Never take pictures while moving.


Never use this camera while you are walking or while you are in control of a
vehicle such as a car.
This can cause a collision or traffic accident.

Do not touch metal components during a thunderstorm.


This can result in an electric shock from lightning induction when lightning
strikes.

Do not use the batteries other than as directed.


Load the batteries with the positive + and negative - poles positioned as
indicated.

Do not attempt to disassemble, modify or heat the batteries.


Do not drop the batteries or subject them to impacts.
Do not attempt to recharge lithium or alkaline batteries.
Do not store batteries with other metal products.
Any of these actions can cause the battery to burst or leak fluid, resulting in a
fire or injury.

Do not use AC power adapters or batteries other than those


specified for use with this camera.
This can cause a fire.

If fluid leaks from the batteries and gets into your eyes or on your
skin or clothing, blindness or injury could result. Flush the affected
area immediately with clean water and seek medical help as soon as
possible.
When disposing of or storing batteries, cover the battery terminals
with insulating tape (cellophane tape, etc.).
• Contact with other batteries or metal objects can cause the batteries to emit
sparks or burst.

Do not use the camera in atmospheres that contain flammable gas.


This can cause an explosion or fire.

Do not use
Do not look directly at the sun or any strong light source through
the camera or lens.
This can cause blindness or damaged eyesight.
Do not look

Take care not to wrap the shoulder strap around your neck. Take
particular care not to catch the shoulder strap around the necks of
infants or small children.
Do not use This can result in the strap becoming wrapped around the neck and cause
suffocation.
Downloaded from ManualsCamera.com Manuals
130
WARNING
Keep button-cell batteries out of the reach of small children to
prevent the batteries from being accidentally swallowed.
If swallowed, button-cell batteries can cause symptoms of poisoning. If a
battery is swallowed, consult a physician immediately.

ATTENTION
Do not leave the camera in very humid or dusty locations or
locations affected by oil smoke or steam.
Leaving the camera in such locations may cause a fire or electric shock.

Do not leave the camera in unusually hot locations.


Do not leave the camera in a closed car or in a location exposed to direct
sunlight.
This could cause a fire.

Do not place heavy objects on the camera.


The camera could overbalance and fall, resulting in an injury.

Do not move the camera while the AC power adapter is connected.


This could damage the power cord or the cable and cause a fire or electric
shock.

Do not cover the camera or AC power adapter with blankets or


bedding.
This can cause heat to build up and result in deformation of the camera casing
or a fire.

When cleaning the camera or when the camera will not be used for
an extended period, remove the batteries and disconnect the AC
power adapter.
Failure to do so could cause a fire or electric shock.

Do not operate the flash close to people’s eyes.


This can cause temporarily damaged eyesight.

Regularly request internal inspections and cleaning.


The buildup of dust inside the camera could cause camera faults or a fire.
• Contact an authorized FUJIFILM dealer and request internal cleaning once
every two years.

When you are not using the camera, fit the lens cap on the lens and
store the camera out of direct sunlight.
Sunlight entering the lens could cause a fire.
Storage note

Do not move the camera or lens while it is mounted on a tripod.


The camera could fall over or strike someone and cause an injury.
Do not move
5
Downloaded from ManualsCamera.com Manuals
131
26-30, Nishiazabu 2-chome, Minato-ku, Tokyo 106-8620, Japan Printed on recycled paper.

Printed in Japan FGS-002107-SZ


Downloaded from ManualsCamera.com Manuals

You might also like