PT-AE2000U: Operating Instructions

Operating Instructions
LCD Projector
Model No. PT-AE2000U
Before operating this product, please read the instructions carefully and save this manual for future use.
TQBJ0233
ENGLISH
Important Safety Notice
Information
Important
Dear Panasonic Customer:

The following information should be read and understood as it provides details, which will enable you to operate the
projector in a manner which is both safe to you and your environment, and conforms to legal requirements regarding
the use of projectors. Before connecting, operating or adjusting this projector, please read these instructions
completely and save this booklet with the projector for future reference. We hope it will help you to get the most out
of your new product, and that you will be pleased with your Panasonic LCD projector.
The serial number of your product may be found on its bottom. You should note it in the space provided below and
retain this booklet in case service is required.
Model number: PT-AE2000U
Serial number:
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DONOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
Power Supply: This LCD Projector is designed to operate on 100 V - 240 V, 50 Hz/60 Hz AC, house current
only.
CAUTION: The AC power cord which is supplied with the projector as an accessory can only be used for
power supplies up to 125 V, 7 A. If you need to use higher voltages or currents than this, you will
need to obtain a separate 250 V power cord. If you use the accessory cord in such situations, fire
may result.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
product.
CAUTION: This equipment is equipped with a three-pin grounding-type power

plug. Do not remove the grounding pin on the power plug. This plug
will only fit a grounding-type power outlet. This is a safety feature. If
you are unable to insert the plug into the outlet, contact an
electrician. Do not defeat the purpose of the grounding plug.
Do not remove
NOTICE: This product has a High Intensity Discharge (HID) lamp that contains mercury. Dispose may be
regulated in your community due to environmental considerations. For disposal or recycling
information, please contact your local authorities, or the Electronic Industries Alliance: http://
www.eiae.org
2 - ENGLISH
Important Safety Notice
Information
Important
WARNING:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION: To assure continued compliance, use only shielded interface cables when
connecting to computers or peripheral devices. Any unauthorized
changes or modifications to this equipment will void the users authority to
operate.
If you use serial port to connect PC for external control of projector, you
must use optional RS-232C serial interface cable with ferrite core. Any
unauthorized changes or modifications to this equipment will void the
user’s authority to operate.
Pursuant to at the directive 2004/108/EC, article 9(2)

Panasonic Testing Center
Panasonic Service Europe, a division of Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, F.R. Germany
WARNING: Not for use in a computer room as defined in the Standard for the Protection
of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75.
Declaration of Conformity
Model Number: PT-AE2000U
Trade Name: Panasonic
Responsible party: Panasonic Corporation of North America
Address: One Panasonic Way, Secaucus, New Jersey 07094
Telephone number: (888) 411 - 1996
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Information on Disposal in other Countries outside the European Union

This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct
method of disposal.
ENGLISH - 3
Contents
J Quick steps Important Information
Important Safety Notice........................................ 2
1. Set up your projector Precautions with regard to safety ....................... 6
WARNINGS................................................................. 6
See “Setting up” on page 14. CAUTIONS .................................................................. 8
Cautions when transporting......................................... 9
Cautions when installing.............................................. 9
Cautions on use ........................................................ 10
Accessories ............................................................... 10
2. Connect with other devices Preparation

See “Connections” on page 18. About Your Projector.......................................... 11
Remote control .......................................................... 11
Projector body ........................................................... 12
Getting Started
Setting up............................................................. 14
3. Prepare the remote control Screen size and throw distance................................. 14
See “Remote control” on page 11. Projection method...................................................... 15
Front leg adjusters and throwing angle ..................... 15
Lens shift and positioning .......................................... 16
Connections ........................................................ 18
Before connecting to the projector............................. 18
Connecting to COMPONENT IN/VIDEO IN/S-VIDEO IN ....18
Connecting to COMPUTER IN/HDMI IN ................... 18
4. Start projecting
See “Switching the projector on/off” on
page 19. Basic Operation
Switching the projector on/off ........................... 19
Power cord ................................................................ 19
POWER indicator ...................................................... 19
Switching on the projector ......................................... 20
Switching off the projector ......................................... 20
Projecting an image ............................................ 21
5. Adjust the image Selecting the input signal........................................... 21
See “Menu Navigation” on page 28. Positioning the image ................................................ 21
Remote control operation .................................. 22
Operating range ........................................................ 22
Turning on the button backlight ................................. 22
Resetting to the factory default settings .................... 22
Capturing an image ................................................... 22
Switching the input signal .......................................... 23
Switching the aspect ratio.......................................... 23
Loading a saved setting ............................................ 23
Adjusting the signal condition with a waveform ......... 24
Adjusting the focus and zoom ................................... 25
Switching the picture mode ....................................... 25
Adjusting the image ................................................... 25
Switching off the projector automatically ................... 25
Setting your own color profile .................................... 26
4 - ENGLISH
Contents
Infomation
Settings Maintenance
Important
Menu Navigation ..................................................28 TEMP and LAMP Indicators ............................... 42
Main menu and sub-menu ........................................ 28 Managing the indicated problems ............................. 42
Navigating through the MENU .................................. 30 Care and Replacement ....................................... 43
PICTURE menu.....................................................31 Cleaning the projector............................................... 43
PICTURE MODE....................................................... 31 Replacing the lamp unit ............................................ 44
CONTRAST .............................................................. 31 Troubleshooting .................................................. 46
BRIGHTNESS........................................................... 31
COLOR ..................................................................... 31
Preparation
TINT .......................................................................... 31
SHARPNESS ............................................................ 31 Appendix
COLOR TEMPERATURE ......................................... 32 Technical Information ......................................... 47
DYNAMIC IRIS.......................................................... 32 List of compatible signals.......................................... 47
WAVEFORM MONITOR ........................................... 32 Serial terminal ........................................................... 48
SPLIT ADJUST ......................................................... 32 Ceiling mount bracket safeguards ............................ 51
ADVANCED MENU................................................... 33 Specifications............................................................ 52
MEMORY SAVE ....................................................... 34 Dimensions ............................................................... 54
MEMORY LOAD ....................................................... 34 Trademark acknowledgements................................. 55
Getting Started
MEMORY EDIT ......................................................... 35 Index ..................................................................... 56
SIGNAL MODE ......................................................... 35
POSITION menu ...................................................36
H-POSITION ............................................................. 36
V-POSITION ............................................................. 36
DOT CLOCK ............................................................. 36
CLOCK PHASE......................................................... 36
ASPECT .................................................................... 36
WSS .......................................................................... 38
OVER SCAN ............................................................. 38
Basic Operation
KEYSTONE............................................................... 38
AUTO SETUP ........................................................... 38
LENS CONTROL...................................................39
ZOOM/FOCUS .......................................................... 39
FUNCTION BUTTON.............................................39
BUTTON1/2/3 ........................................................... 39
OPTION menu.......................................................40
INPUT GUIDE ........................................................... 40
OSD DESIGN............................................................ 40
OSD POSITION ........................................................ 40
BACK COLOR........................................................... 40
STARTUP LOGO ...................................................... 40
Settings
AUTO SEARCH ........................................................ 40
HDMI SIGNAL LEVEL............................................... 40
FRAME RESPONSE................................................. 40
INSTALLATION......................................................... 41
SLEEP....................................................................... 41
ALTITUDE ................................................................. 41
LAMP POWER .......................................................... 41
LAMP RUNTIME ....................................................... 41
Maintenance
Appendix
ENGLISH - 5
Precautions with regard to safety
Information
Important
WARNINGS
If you notice smoke, strange smells or noise coming Do not place the projector on top of surfaces which
from the projector, disconnect the power plug from are unstable.
the wall outlet. If the projector is placed on top of a surface which is
Do not continue to use the projector in such cases, sloped or unstable, it may fall down or tip over, and
otherwise fire or electric shocks could result. injury or damage could result.
Check that no more smoke is coming out, and then
contact an Authorized Service Center for repairs. Do not place the projector into water or let it become
Do not attempt to repair the projector yourself, as this wet.
can be dangerous. Failure to observe this may result in fire or electric
shocks.
Do not install this projector in a place which is not
strong enough to take the full weight of the Do not do anything that might damage the power
projector. cord or the power plug.
If the installation location is not strong enough, it may Do not damage the power cord, make any
fall down or tip over, and severe injury or damage modifications to it, place it near any hot objects, bend
could result. it excessively, twist it, pull it, place heavy objects on
top of it or wrap it into a bundle.
Installation work (such as ceiling suspension) If the power cord is used while damaged, electric
should only be carried out by a qualified technician. shocks, short-circuits or fire may result.
If installation is not carried out correctly, there is the Ask an Authorized Service Center to carry out any
danger that injury or electric shocks may occur. repairs to the power cord that might be necessary.
Do not use other than an authorized ceiling mount
bracket. Do not place the projector on soft materials such as
carpets or sponge mats.
If foreign objects or water get inside the projector, or Doing so may cause the projector to overheat, which
if the projector is dropped or the cabinet is broken, can cause burns, fire or damage to the projector.
disconnect the power plug from the wall outlet.
Continued use of the projector in this condition may Do not place liquid containers on top of the
result in fire or electric shocks. projector.
Contact an Authorized Service Center for repairs. If water spills onto the projector or gets inside it, fire
or electric shocks could result.
Do not overload the wall outlet. If any water gets inside the projector, contact an
If the power supply is overloaded (for example, by Authorized Service Center.
using too many adapters), overheating may occur
and fire may result. Do not insert any foreign objects into the projector.
Do not insert any metal objects or flammable objects
Never attempt to modify or disassemble the into the projector or drop them onto the projector, as
projector. doing so can result in fire or electric shocks.
High voltages can cause fire or electric shocks.
For any inspection, adjustment and repair work, Do not allow the + and - terminals of the batteries to
please contact an Authorized Service Center. come into contact with metallic objects such as
necklaces or hairpins.
Clean the power plug regularly to prevent it from Failure to observe this may cause the batteries to
becoming covered in dust. leak, overheat, explode or catch fire.
If dust builds up on the power plug, the resulting Store the batteries in a plastic bag and keep them
humidity can damage the insulation, which could away from metallic objects.
result in fire. Pull the power plug out from the wall
outlet and wipe it with a dry cloth. Do not touch the leaked liquid from the batteries.
If not using the projector for an extended period of If you touch the leaked liquid, it may hurt your skin.
time, pull the power plug out from the wall outlet. Immediately wash away the liquid with water and
seek medical advice.
Do not handle the power plug with wet hands. If you get the leaked liquid in your eye, it may cause
Failure to observe this may result in electric shocks. blindness or damage. Never rub your eye, and
immediately wash away the liquid with water and
Insert the power plug securely into the wall outlet. seek medical advice.
If the plug is not inserted correctly, electric shocks or
overheating could result. During a thunderstorm, do not touch the projector or
Do not use plugs which are damaged or wall outlets the cable.
which are coming loose from the wall. Electric shocks can result.
6 - ENGLISH
Information
Important
Do not use the projector in a bath or shower.
Fire or electric shocks can result.
Do not place your skin into the light beam while the
projector is being used.
Strong light is emitted from the projector’s lens. If you
place directly into this light, it can hurt or damage
your skin.
Do not look into the lens while the projector is being

used.
Strong light is emitted from the projector’s lens. If you
look directly into this light, it can hurt and damage
your eyes.
Be especially careful not to let young children look
into the lens. In addition, turn off the power and
disconnect the power plug when you are away from
the projector.
Do not place your hands or other objects close to the

air outlet port.
Heated air comes out of the air outlet port. Do not
place your hands or face, or objects which cannot
withstand heat close to this port [allow at least
50 cm (20") of space], otherwise burns or damage
could result.
Replacement of the lamp is recommended to be

carried out by a qualified technician.
The lamp has high internal pressure. If improperly
handled, explosion might result.
The lamp can easily become damaged if struck
against hard objects or dropped, and injury or
malfunctions may result.
When replacing the lamp, allow it to cool for at least

one hour before handling it.
The lamp cover gets very hot, and touching it can
cause burns.
Before replacing the lamp, be sure to disconnect the

power plug from the wall outlet.
Electric shocks or explosions can result if this is not
done.
Do not allow infants or pets to touch the remote

control unit.
The accessory remote control unit can be used to
operate not only the projector but also other
appliances such as air conditioners and electrical
device by programming them using the learning
function. If the remote control unit operated
inappropriately, fire or injury may result.
Keep the remote control unit out of the reach of
infants and pets after using it.
ENGLISH - 7
Information
Important
CAUTIONS
Do not cover the air inlet port or the air outlet port. Use only the specified batteries.
Doing so may cause the projector to overheat, which If incorrect or different kind of batteries are used, they
can cause fire or damage to the projector. may explode or leak, and fire, injury or contamination
Do not place the projector in narrow, badly ventilated of the battery compartment and surrounding area
places such as closets or bookshelves. may result.
Do not place the projector on cloth or papers, as
these materials could be drawn into the air inlet port. Do not mix old and new batteries.
If the batteries are inserted incorrectly, they may
Do not set up the projector in humid or dusty places explode or leak, and fire, injury or contamination of
or in places where the projector may come into the battery compartment and surrounding area may
contact with oily smoke or steam. result.
Using the projector under such conditions may result
in fire, electric shocks or plastic deterioration. The Remove the used batteries from the remote control
plastic deterioration may cause the falling down of promptly.
the projector which is mounted in the ceiling. If you leave used batteries in the remote control for
an extended period of time, it may cause liquid
Do not set up the projector in a high temperature leaking, abnormal internal temperature rising or
environment, such as near a heater or in direct explosion.
sunlight.
Failure to observe this may result in fire, malfunction If not using the projector for an extended period of
or plastic deterioration. time, disconnect the power plug from the wall outlet
and remove the batteries from the remote control.
Do not set up the projector outdoors. If dust builds up on the power plug, the resulting
The projector is designed for indoor use only. humidity may damage the insulation, which could
result in fire.
When disconnecting the power cord, hold the plug, Keeping or leaving the remote control with batteries
not the cord. inside may cause insulation deterioration, electrical
If the power cord itself is pulled, the cord will become leakage or explosion which could result in fire.
damaged, and fire, short-circuits or serious electric
shocks may result. Do not put your weight on this projector.
You could fall or the projector could break, and injury
Always disconnect all cables before moving the may result.
projector. Be especially careful not to let young children stand
Moving the projector with cables still attached can or sit on the projector.
damage the cables, which could cause fire or electric
shocks to occur. Disconnect the power plug from the wall outlet as a
safety precaution before carrying out any cleaning.
Do not place any heavy objects on top of the Electric shocks can result if this is not done.
projector.
Failure to observe this may cause the projector to If the lamp has broken, ventilate the room
become unbalanced and fall, which could result in immediately. Do not touch or bring your face close
damage or injury. to the broken pieces.
Failure to observe this may cause the user to absorb
Do not short-circuit, heat or disassemble the the gas which was released when the lamp broke and
batteries or place them into water or fire. which contains nearly the same amount of mercury
Failure to observe this may cause the batteries to as fluorescent lamps, and the broken pieces may
overheat, leak, explode or catch fire, and burns or cause injury.
other injury may result. If you believe that you have absorbed the gas or that
the gas has got into your eyes or mouth, seek
When inserting the batteries, make sure the medical advice immediately.
polarities (+ and -) are correct. Ask your dealer about the replacement of the lamp
If the batteries are inserted incorrectly, they may unit and check the inside of the projector.
explode or leak, and fire, injury or contamination of
the battery compartment and surrounding area may
result.
8 - ENGLISH
Information
Important
Ask an Authorized Service Center to clean inside the
projector at least once a year.
If dust is left to build up inside the projector without
being cleaned out, it can result in fire or problems
with operation.
It is a good idea to clean the inside of the projector
before the season for humid weather arrives. Ask
your nearest Authorized Service Center to clean the
projector when required. Please discuss with the
Authorized Service Center regarding cleaning costs.
We are constantly making efforts to preserve and maintain a clean environment. Please take non repairable
units back to your dealer or a recycling company.
Cautions when transporting

Do not subject the projector to excessive vibration When transporting the projector, hold the body at
or shocks. the bottom securely.
The projector lens need to be handled with care. Do not hold the adjuster legs or the top cover to move
Cover the lens with the lens cover when transporting the projector, as this may damage the projector.
the projector.
Cautions when installing

Avoid setting up in places which are subject to If installing the projector to the ceiling, ask a
vibration or shocks. qualified technician or an Authorized Service Center
The internal parts can be damaged, which may cause to carry out all installation work.
malfunctions or accidents. You will need to purchase the separate installation kit
(Model No. ET-PKE2000, ET-PKE1000S).
Avoid setting up in places which are subject to Furthermore, all installation work is should only be
sudden temperature changes, such as near an air carried out by a qualified technician.
conditioner or lighting equipment. See “Ceiling mount bracket safeguards” on page 51
The life of the lamp may be shortened or the projector for the safety cable installation.
may be turned off. See “TEMP indicator” on page 42.
If using this projector at high elevations
Do not set up the projector near high-voltage power (above 1 400 m), set the HIGHLAND to ON. See
lines or near motors. “ALTITUDE” on page 41.
The projector may be subject to electromagnetic Failure to observe this may result in malfunctions or
interference. the life of the lamp or the other components may be
shortened.
ENGLISH - 9
Information
Important
Cautions on use
In order to get the best picture quality The projector has a high pressure mercury lamp and
Draw curtains or blinds over any windows and turn off that is characterized as follows.
any lights near the screen to prevent outside light or The brightness of the lamp depends on the duration
light from indoor lamps from shining onto the screen. of use.
The lamp may explode or shorten the lamp life by
Do not touch the surfaces of the lens with your bare shocks or chipping damage.
hands. The lamp may explode only occasionally after using
If the surface of the lens becomes dirty from the projector.
fingerprints or anything else, this will be magnified The lamp may explode if using the projector after the
and projected onto the screen. Moreover, when not instructed lamp replacement timing.
using the projector, attach the lens cover. The lamp life is depends on individual lamp
characteristics, usage condition and the installation
Liquid crystal panel environment. Especially the consecutive use of the
Do not project the same image for long periods of projector for more than 10 hours, or the frequent
time, as this may remain as an afterimage on the switching on or off may greatly affect on the lamp life.
liquid crystal panel.
The liquid crystal panel of the projector is built with Screen
very high precision technology to provide fine picture Do not apply any volatile substances which may
details. Occasionally, a few stuck pixels may appear cause discoloration to the screen, and do not let it
on the screen as fixed points of blue, green or red. It become dirty or damaged.
is recommended to switch off the projector once and
try after 1 hour later again. Please note that this does Optical components
not affect the performance of your LCD. If you use the projector consecutively 6 hours every
day, the optical components may need to be replaced
in less than 1 year.
Accessories
Make sure the following accessories are provided with your projector.
Remote control for AA batteries for remote Safety cable Lens cover (x1)
PT-AE2000U (x1) control (x2) TTRA0141 TXFKK01VKF5
EUR7914Z60 Attachment screw (x1)
Safety cable (x1)
Power cord (x1)

K2CG3FZ00008
3 m (9'10")
10 - ENGLISH
About Your Projector
Remote control
POWER button
While the MAIN POWER
button is on, switch between
stand-by mode and projection
mode. (page 19) Remote control signal emitter
Preparation
Remote control signal. (page 22)
Display the main menu or
return to the previous menu. Turn the button backlight
(page 30) of the remote control on/
off. (page 22)
Navigate through the
menus with FGIH,
and activate the menu
item with ENTER.
Function buttons
(page 30)
Assign the frequently used functions
from the options for shortcut. (page 39)
Reset some of the settings
to the factory default
Learning remote control buttons and
settings. (page 22)
LCD
Program and operate other devices.
Battery compartment See “Remote Control Operating Guide”
1. Press the tab and lift up the cover. which is provided with the projector.
2. Insert the batteries according to the
polarity diagram indicated inside.
Return to the previous menu.
(page 30)
Capture the projected

image as a still image.
(page 22)
Switch to cycle through Display the LENS Turn off the power
the input method. CONTROL menu and automatically by setting
(page 23) adjust the focus and size the duration. (page 25)
of the image. (page 25)
Switch to cycle through Switch to cycle through Display the MEMORY
the aspect ratio. the PICTURE MODE. LOAD menu. (page 23)
(page 23) (page 25)
Display the input Display the PICTURE Display the COLOR
waveform. (page 24) menu. (page 25) MANAGEMENT menu.
(page 26)
NOTE:
• Do not drop the remote control.
• Avoid contact with liquids or moisture.
• Use manganese batteries or alkaline batteries with the remote control.
• Do not attempt to modify or disassemble the remote control. Contact an Authorized Service Center for repairs.
• Do not keep pressing the remote control buttons as this may shorten battery life.
• Do not point the laser in other people’s eyes or stare into beam.
• See “Remote control operation” on page 22.
ENGLISH - 11
Projector body
J Top and front view
Lens shift dial • Vertical Lens shift dial • Horizontal
(page 16) (page 16)
Air exhaust port
Heated air comes out of
Preparation
this opening.
POWER/LAMP/TEMP
indicators
(page 19/page 42)
Air filter
(page 43)
MAIN POWER
Switch the projector on/off
Projection lens (page 20)
Lens cover Remote control signal Air exhaust port

Protects the projection lens receptor Heated air comes
from dust or dirt. (page 22) out of this opening.
INPUT SELECT
Switch to cycle through the
input method. (page 21)
(Push to open/close the cover.)

Navigate through the menus with F G H I,
and activate the menu item with ENTER.
(page 30)
POWER
While the MAIN POWER is on, switch between
stand-by mode and project mode. (page 19)
MENU
Display the main menu.
Return to the previous menu. (page 30)
RETURN FOCUS and ZOOM

Return to the previous menu. Adjust the focus and size of the
(page 30) image. (page 21)
NOTE:
• Do not cover the ventilation openings or place anything within 50 cm (20") of them as this may cause damage or injury.
• While the projector is not in use, keep the lens cover to protect the lens.
12 - ENGLISH
J Back and bottom view
Security lock
Attach the commercial shackle lock
Air intake port
which is provided with the projector. Top cover
Preparation
Compatible with the Kensington Hold at the back corner of the top
MicroSaver Security System. cover and slightly push up to open.
(page 51) (page 44)
Air intake port
AC IN
Connect the power cord to
supply electronic power to the
projector. (page 19)
Safety cable attachment point

Attach the safety cable when
mounted in the ceiling.
(page 51)
Front leg adjusters

Screw up/down to adjust the
Front leg adjusters Lens cover attachment hole projection angle. (page 15)
Screw up/down to adjust the
projection angle. (page 15)
COMPUTER IN
Connect an RGB signal cable COMPONENT IN
S-VIDEO IN
from your PC. Connect YPBPR signal cables.
Connect a S-VIDEO
signal cable.
VIDEO IN
Connect an RCA
composite video cable.
Connecting
terminals
(page 18)
SERIAL
HDMI IN Connect a compatible cable for
Connect HDMI signal cables. controlling the projector
remotely via your computer.
(page 48)
NOTE:
• Do not cover the ventilation openings or place anything within 50 cm (20") of them as this may cause damage or injury.
• The projector should only be used with the attached power cord to ensure optimum performance and avoid damage to the
projector.
• Do not open the top cover other than replacing the lamp unit.
ENGLISH - 13
Setting up
Screen size and throw distance
You can adjust the projection size with 2.0x zoom lens. Calculate and define the throw distance as follows.
SD
Projected image SH
SW
Screen
Getting Started
Projection size (16 : 9) Throw distance (L)

Screen Diagonal Minimum distance Maximum distance
Screen height (SH) Screen width (SW)
(SD) (LW) (LT)
1.01 m (40") 0.50 m (1'7") 0.89 m (2'11") 1.2 m (3'11") 2.3 m (7'6")
1.27 m (50") 0.62 m (2') 1.11 m (3'7") 1.5 m (4'11") 2.9 m (9'6")
1.52 m (60") 0.75 m (2'5") 1.33 m (4'4") 1.8 m (5'10") 3.5 m (11'5")
1.77 m (70") 0.87 m (2'10") 1.55 m (5'1") 2.1 m (6'10") 4.1 m (13'5")
2.03 m (80") 1.00 m (3'3") 1.77 m (5'9") 2.4 m (7'10") 4.7 m (15'8")
2.28 m (90") 1.12 m (3'8") 1.99 m (6'6") 2.7 m (8'10") 5.3 m (17'4")
2.54 m (100") 1.25 m (4'1") 2.21 m (7'3") 3.0 m (9'10") 5.9 m (19'4")
3.05 m (120") 1.49 m (4'10") 2.66 m (8'8") 3.6 m (11'9") 7.2 m (23'7")
3.81 m (150") 1.87 m (6'1") 3.32 m (10'10") 4.5 m (14'9") 9.0 m (29'6")
5.08 m (200") 2.49 m (8'2") 4.43 m (14'6") 6.0 m (19'8") 12.0 m (39'4")
* All measurements above are approximate and may differ slightly from the actual measurements.
J Calculation methods for screen dimensions
You can calculate more detailed screen dimension from the screen diagonal.
SW (m) = SD (m) x 0.872 SH (m) = SD (m) x 0.490
LW (m) = 1.189 x SD (m) - 0.04 LT (m) = 2.378 x SD (m) - 0.05
* The results above are approximate and may differ slightly from the actual measurements.
NOTE:
• Do not use the projector at a raised or a horizontally tilted position as it may cause
malfunction of the projector.
• Make sure the projector lens surface is parallel with the screen. You can tilt the projector
body less than approximately ± 30° vertically. Overtilting may result in shortening the
component’s life.
• For the best quality of the projection image, install a screen where sun light or room light
does not shine directly onto the screen. Close window shades or curtains to block the lights.
14 - ENGLISH
Setting up
Projection method
You can use the projector with any of the following 4 projection methods. To set the desired method in the projector,
See “INSTALLATION” on page 41.
J Setting on a desk/floor and J Setting on a desk/floor and
projecting from front projecting from rear
Getting Started
INSTALLATION: FRONT/DESK INSTALLATION: REAR/DESK
J Mounting in the ceiling and J Mounting in the ceiling and
projecting from front projecting from rear
INSTALLATION: FRONT/CEILING INSTALLATION: REAR/CEILING
NOTE:
• A translucent screen is required for rear projection.
• When mounting the projector in the ceiling, the optional ceiling mount bracket (ET-PKE2000, ET-PKE1000S) is required.
• See “Ceiling mount bracket safeguards” on page 51.
Front leg adjusters and throwing angle

You can screw up/down the front leg adjusters to control the angle of the projector for adjusting the throwing angle.
See “Positioning the image” on page 21.
NOTE:
• Heated air comes out of the air exhaust port. Do not touch the air exhaust port directly.
• If keystone distortion occurs, see “KEYSTONE” on page 38.
• Screw up the adjuster legs, and an audible click will be heard as the limit.
ENGLISH - 15
Setting up
Lens shift and positioning

If the projector is not positioned right in front of the center of the screen, you can adjust the projected image position
by moving the lens shift dials within the shift range of the lens.
J Adjusting the lens shift dials
Q Horizontal shift
You can place the projector where the projector lens is up to 40% horizontally off-center from the screen and
then adjust the image position with the Lens shift dial • Horizontal.
Up to about 40 % Up to about 40 %
of the projection of the projection
Getting Started
Turn the dial clockwise: Turning the dial counterclockwise:

Moving to screen’s right Moving to screen’s left
Q Vertical shift
You can place the projector where the projector lens is up to 100% vertically off-center from the screen and the
adjust the image position with the Lens shift dial • Vertical.
Shifting the lever down:

Moving to screen’s bottom.
Up to about 100 %
of the projection
Up to about 100 %
of the projection
Shifting the lever up:

Moving to screen’s top.
16 - ENGLISH
Setting up
J Projector location range
You can determine where to locate the screen and the projector by considering the lens shift possibilities. See
“Positioning the image” on page 21.
Q When the screen position is fixed
H
Projector
Placement
V
Vertical center of
screen
SH Center of lens
Getting Started
Screen SW
Q When the projector position is fixed
100% Shift range
100%
40% 40%
Projector
NOTE:
• When the projector is located right in front of the screen and the lens shift dials is centered, you will get the best quality of
the projection image.
• When the Lens shift dial • Vertical is at the vertical limit of the shift range, you cannot turn the dial to the horizontal limit,
likewise when the Lens shift dial • Horizontal is at the horizontal limit of the shift range, you cannot turn the dial to the
horizontal limit.
• When the projector is tilted and you adjust KEYSTONE, the center of the screen and the lens need to be realigned.
• Do not force the lens shift dials to turn as this may damage the projector. Turning the dials maximum limit is 4 or 5 times
from the default position.
ENGLISH - 17
Connections
Before connecting to the projector
Read and follow the operating and connecting instructions of each peripheral device.
The peripheral devices must be turned off.
Use cables that match each peripheral device to be connected.
Confirm the type of video signals. See “List of compatible signals” on page 47.
Audio cables must be connected from each peripheral device directly to the audio reproduction system.
Connecting to COMPONENT IN/VIDEO IN/S-VIDEO IN

\
Getting Started
To COMPONENT
video output To VIDEO output To S-VIDEO output
DVD player Video player DVD player
Connecting to COMPUTER IN/HDMI IN
RGB signal cable

HDMI cable (Commercial item)
(RP-CDHG100: Optional))
To HDMI output
DVD player
Computer
NOTE:
• Make sure the HDMI cable is adapted to your HDMI device for proper performance.
• A compatible cable is required for an HDMI 1 080p signal.
• It is possible to connect with DVI devices via a HDMI/DVI conversion adapter, but some equipment may not project the
image properly or other problems could be encountered. “Serial terminal” on page 48
18 - ENGLISH
Switching the projector on/off
Power cord
J Connecting J Disconnecting
1. Make sure the shape of 1. Make sure the MAIN POWER is switched off and
the power plug and the unplug the power cord from the wall outlet.
AC IN connector on the 2. Hold the plug and unplug the power cord from the
back of the projector AC IN connector on the side of the projector.
match, then push the plug all the way in.
2. Connect the power cord to a wall outlet.
NOTE:
• Do not use other than the provided power cord.
• Ensure all the input devices are connected and turned off before connecting the power cord.
• Do not force the connector as this may damage the projector and/or the power cord.
• Dirt or dust build-up around plugs may cause fire or electrical hazards.
• Switch off the power to the projector when not in use.
POWER indicator
Basic Operation
POWER indicator
Indicator status Status
No illumination or flashing The MAIN POWER button is switched off.
Red Lit The MAIN POWER button is switched on and the projector is in standby.
Flashing The POWER button is switched on and the projector is getting ready to project.
Green
Lit The projector is ready to project.
Lit The POWER button is switched off and the projector is cooling the lamp.
Orange The POWER button is switched on again when cooling the lamp and recovering to
Flashing
projection mode. Recovery may take a while.
NOTE:
• While the projector is cooling the lamp, do not switch the MAIN POWER button off or unplug the power cord.
• The electric consumption in standby mode is 0.08 W.
ENGLISH - 19
Switching the projector on/off
Switching on the projector

POWER indicator
(1)
(3)
(2)
1. Switch the MAIN POWER button on. 3. Press the POWER button.
The power indicator lights up in red. The power indicator lights up in green after flashing
2. Remove the lens cover from the lens. for a while.
The STARTUP LOGO is displayed on the screen.
See “STARTUP LOGO” on page 40.
NOTE:
• When starting up the projector, some small rattling or tinkling sound may be heard, or the display may flicker for the
characteristics of the lamp. Those are normal and do not affect the performance of the projector.
• Do not attempt to modify the lens cover which may cause burns, fire or damage to the projector.
Basic Operation
Switching off the projector

POWER indicator
(3)
(1)
(2)
1. Press the POWER button. 2. Press I to select OK and press the POWER or
The confirmation screen is displayed. It will ENTER button.
disappear and return to the projection after The power indicator lights up in orange while cooling
10 seconds without any operation. the lamp, then illuminates red when it is ready to
To return to the projection, press any button except switch off the MAIN POWER button.
the POWER button. 3. Switch off the MAIN POWER button on the back of
the projector.
NOTE:
• Press the POWER twice or for a long duration to switch the power off.
20 - ENGLISH
Projecting an image
Selecting the input signal
1. Switch on the connected devices.
Press the play button of the required device. NOTE:
2. Press the INPUT button to select the required input • AUTO SEARCH is ON as default and the signal from
method if needed. See “Switching the input signal” the connected devices is detected automatically. See
on page 23. “AUTO SEARCH” on page 40.
The image will be projected on the screen.
Positioning the image

1. Press the ASPECT button to select the required 4. Adjust the focus and the projected image size.
aspect mode. See “Switching the aspect ratio” on Press +/- of the FOCUS and ZOOM buttons to
page 23. adjust.
2. Adjust the projected image with the lens shift dials. Press the LENS button to adjust the focus and zoom
See “Lens shift and positioning” on page 16. by the remote control. See........................
Basic Operation
3. Adjust the angle of the projector.
Screw down the front leg adjusters and adjust the
angle vertically. NOTE:
See “Front leg adjusters and throwing angle” on • Do not touch the air exhaust port as this may cause
page 15. burns or injury.
• If keystone distortion occurs, see “KEYSTONE” on
page 38.
• If you adjust the focus, you may need to adjust the size
of the image by pressing the ZOOM button again.
ENGLISH - 21
Remote control operation
Operating range
You can operate the projector with the remote control
within the remote range 7 m (22'11").
Q Facing to the projector
Ensure the remote control emitter is facing to the
remote control signal receptor on front/back of the
projector and press the required buttons to
operate.
Q Facing to the screen
Ensure the remote control emitter is facing to the
screen and press the required buttons to operate
the projector. The signal will be reflected off the
screen. The operating range may differ due to the
screen material. This function may not be effective
with a translucent screen.
NOTE:
• Do not let strong light shine onto the signal receptor.
The remote control may malfunction under strong light
such as fluorescent.
• If there are any obstacles between the remote control
and the remote control signal receptor, the remote
Basic Operation
control may not operate correctly.
Turning on the button backlight

In a dark room, you can turn on the button After 30 seconds without any operation, the backlight will
backlight to operate the remote control. go out and press any but the LIGHT button to turn on
Press the LIGHT button on the upper right again. To escape from the light-on mode, press the
corner of the unit to turn on the backlight and LIGHT button.
enter the light-on mode.
Resetting to the factory default settings

You can reset most of the customized
settings to the factory defaults by pressing NOTE:
DEFAULT button of the remote control. • Some menu items are not available to reset by pressing
Display the required sub-menu or the menu the DEFAULT button. Adjust each menu items
items and press the button again. manually.
Capturing an image
When projecting an image, press FREEZE You can adjust AREA SELECT of the SPLIT ADJUST
button to capture the projected image and menu by pressing the ENTER button while the frozen
display it on the screen as a still picture. Press image is displayed. See “SPLIT ADJUST” on page 32.
again to escape.
22 - ENGLISH
Switching the input signal

You can switch the input method manually
COMPONENT 1 IN COMPONENT (YPBPR) signals
by pressing the INPUT button. Press the from the equipment connected to
button several times or press I H to cycle COMPONENT IN 1/
through the input methods as follows. The COMPONENT 2 IN
COMPONENT IN 2.
actual projected image will be changed in a
S-VIDEO signal from the equipment
while. S-VIDEO IN
connected to S-VIDEO IN.
The graphical guidance will be displayed on the upper
right of the projected image and you can confirm the VIDEO signal from the equipment
VIDEO IN
selected input method which is highlighted in yellow. See connected to VIDEO IN.
“INPUT GUIDE” on page 40.
HDMI 1 IN
COMPONENT 1 IN COMPONENT 2 IN HDMI signal from the equipment
HDMI 2 IN connected to HDMI IN 1/HDMI IN 2/
COMPUTER IN S-VIDEO IN HDMI IN 3.
HDMI 3 IN
COMPUTER (RGB) signal from the

HDMI 3 IN VIDEO IN
COMPUTER IN equipment connected to
COMPUTER IN.
HDMI 2 IN HDMI 1 IN
NOTE:
• If you select an unplugged input method, the guidance will blink on and off several times.
• See “List of compatible signals” on page 47.
• See “Connections” on page 18.
Basic Operation
Switching the aspect ratio
The aspect ratio will be selected Q HDMI
automatically, or you can switch it manually
4:3 16:9
by pressing the ASPECT button. Press the
button several times to cycle through the
different aspect type as follows. See NOTE:
“ASPECT” on page 36. • If you project an image with an unmatched aspect ratio,
the image may distort or some portions may be
Q VIDEO/S-VIDEO/COMPONENT (YPBPR) cropped. Select an aspect ratio which preserves the
intention of the image creator.
4:3 JUST
• The order of aspect type is defined not only by the input
method but also by the input signals. See “List of
16:9 ZOOM2 compatible signals” on page 47.
• If you project a copyrighted image enlarged or distorted
by using ASPECT function in commercial use in a
14:9 ZOOM1
public place, such as a restaurant or hotel, you might
infringe on the copyright of the creator which is
Q COMPUTER (RGB) protected by copyright law.
4:3 16:9
Loading a saved setting

You can access saved settings instantly.
See “MEMORY LOAD” on page 34.
NOTE:
• If you have not saved any settings, MEMORY1 - 16
will not be displayed.
1. Select the required setting from MEMORY1 - 16.
Undefined setting will not be displayed.
2. Press ENTER to activate the selected setting.
ENGLISH - 23
Adjusting the signal condition with a waveform

You can display the image brightness and Monitoring the waveform of
contrast level of the input signal with a FULL SCAN brightness and contrast of the whole
waveform. See “WAVEFORM MONITOR” image.
on page 32. Monitoring the waveform of
SINGLE LINE SCAN brightness and contrast in each
horizontal line of the image.
COMPUTER (except 1080)

HDMI (Expand)
100%
Adjust to 100%
Adjust to 100%
50%
0%
100% 100%
Signal level
Signal level
ENTER
ENTER
50% 50%
Optimal Optimal
0%
dynamic range dynamic range
0%
Adjust to 0% Monitor position Adjust to 0%

Monitor position
J Displaying the waveform J Adjustment example

1. Press the WAVEFORM button and display the Project a commercial test signal for picture
Basic Operation
waveform monitor. adjustment on the screen and press the

Press the WAVEFORM button again to escape from WAVEFORM button.
the waveform mode.
2. Press ENTER button until the required waveform Q Adjusting with luminance options
option is displayed. 1. Press the ENTER button until FULL SCAN(Y)/
In FULL SCAN mode, press F G I H to change SINGLE LINE SCAN(Y) is displayed.
the waveform position. 2. Press the PIC. ADJUST to display the PICTURE
In SINGLE LINE SCAN mode, press F G to select MODE of the PICTURE menu.
the required line position. 3. Press G several times to display the
BRIGHTNESS.
FULL SCAN(Y) SINGLE LINE SCAN(B) 4. Adjust the BRIGHTNESS by pressing I H.
Adjust the bottom line of the waveform to 0%
FULL SCAN(R) SINGLE LINE SCAN(G) (0 or 7.5 IRE).
Setting range: -32 to +32
5. Press G once to display the CONTRAST.
FULL SCAN(G) SINGLE LINE SCAN(R) 6. Adjust the CONTRAST by pressing I H.
Adjust the bottom line of the waveform to 100%
FULL SCAN(B) SINGLE LINE SCAN(Y) (100 IRE).
NOTE: FULL SCAN(Y)/SINGLE LINE SCAN(Y)
• In SINGLE LINE SCAN mode, the position of the
Adjust the bottom line of the
waveform monitor depends on the position of the BRIGHTNESS
waveform to 0% (0 IRE or 7.5 IRE)
selected line.
• You can display the main menu by pressing the MENU Adjust the top line of the waveform
CONTRAST
button and adjust the menu items. to 100% (100 IRE)
• The called up menu items displayed position depends
on the position of the waveform monitor.
• You can activate AUTO ADJUST of the WAVEFORM
menu by pressing the DEFAULT button.
• The signal which is lower than 0% in the waveform will
be displayed as same as 0% on the projected image.
• While the waveform is displayed, the image is
displayed without the COLOR MANAGEMENT
adjustment.
• When adjusting the KEYSTONE of the POSITION
menu while the waveform is displayed, xvYCC will be
deactivated.
24 - ENGLISH
Q Adjusting with RGB options FULL SCAN(R)/SINGLE LINE SCAN(R)
1. Press the ENTER button until the required option Adjust the bottom line of the
BRIGHTNESS R
is displayed. waveform to 0% (0 IRE or 7.5 IRE)
2. Press the PIC. ADJUST twice to display the Adjust the top line of the waveform
CONTRAST R
GAMMA of the ADVANCED MENU menu. to 100% (100 IRE)
3. Press G several times to display the required FULL SCAN(G)/SINGLE LINE SCAN(G)
brightness option. Adjust the bottom line of the
4. Adjust the brightness option by pressing I H. BRIGHTNESS G
Adjust the bottom line of the waveform to 0% Adjust the top line of the waveform
(0 IRE or 7.5 IRE). CONTRAST G
to 100% (100 IRE)
FULL SCAN(B)/
5. Press G once to display the required contrast
Adjust the bottom line of the
option. BRIGHTNESS B
6. Adjust the contrast option by pressing I H.
Adjust the top line of the waveform
Adjust the top line of the waveform to 100% CONTRAST B
to 100% (100 IRE)
(100 IRE).
Adjusting the focus and zoom

You can adjust the focus and zoom of the display the LENS CONTROL menu. See “LENS
projected image. Press the LENS button to CONTROL” on page 39.
Switching the picture mode
Basic Operation
You can switch the preset picture mode
NORMAL CINEMA3
settings by pressing the PIC. MODE button.
Press the button until the required setting is
selected. See “PICTURE MODE” on page 31. DYNAMIC
CINEMA2
COLOR1
COLOR2 CINEMA1
Adjusting the image

You can display the PICTURE and Q ADVANCED MENU items
ADVANCED MENU menu items with called GAMMA, CONTRAST, BRIGHTNESS, xvYCC,
up style by pressing the PIC. ADJUST DETAIL CLARITY, NR, MPEG NR, CINEMA
button. Press the button to switch between REALITY and TV-SYSTEM
PICTURE and ADVANCED MENU menu. Press F G to
select the required menu item and I H to adjust.
Q PICTURE menu items NOTE:
• For each menu items description, see “PICTURE
PICTURE MODE, CONTRAST, BRIGHTNESS,
menu” on page 31.
COLOR, TINT, SHARPNESS, COLOR • The screen will be cleared after 7 seconds without
TEMPERATURE and DYNAMIC IRIS any operation.
Switching off the projector automatically

You can switch off the POWER
OFF 240MIN.
automatically by setting the SLEEP feature.
Press the SLEEP button several times to
cycle through the duration of time. See 60MIN. 210MIN.
“SLEEP” on page 41.
90MIN. 180MIN.
120MIN. 150MIN.
ENGLISH - 25
Setting your own color profile

You can adjust a selected color individually 3. Select a menu item and the I H to adjust each
and save and retrieve under the PICTURE item level.
MODE setting. Press the COLOR M. button The result box is displayed on the right of the cursor
to open the menu. and shows the adjusted color.
CURSOR
RETURN
PROFILE NORMAL SELECT ENTER
COLOR
TINT
BRIGHTNESS
CURSOR DEFAULT
LOG
Adjusted color
PROFILE SAVE
PROFILE DELETE
PROFILE NAME CHANGE
J Create a new profile

Adjust the vividness of the color.
Q Adjusting the selected color COLOR
Select a color and adjust COLOR, TINT and Adjust the color tone.
BRIGHTNESS. TINT
1. Select the CURSOR menu and press ENTER. Adjust the brightness of the color.
The projected image is captured, and the target BRIGHTNESS
cursor is displayed.
When the LOG is fully stored, the target cursor will
4. Press ENTER to store the adjusted result.
“PROCESSING” is displayed for a few seconds and
not be displayed. See “Managing stored logs” on
Basic Operation
the result is stored in LOG.

page 26.
You can store up to 8 logs under LOG for each
Target cursor PICTURE MODE setting.
5. Press MENU or RETURN to return to the previous
menu.
Repeat the steps above to store more adjustment.
Q Managing stored logs

You can edit or delete the stored logs of the
selected PICTURE MODE.
1. Select LOG and press ENTER.
The LOG menu is displayed.
2. Move the cursor with F G I H to the required
PICTURE MODE : CINEMA1
place to select a color and press ENTER.
The color at the center of the target cursor is
sampled and the sample box is displayed on the left POINT1
of the cursor. The menu items are displayed on the POINT2
POINT3
upper part of the screen.
POINT4
POINT5
POINT6
CURSOR POINT7
RETURN COLOR POINT8
SELECT TINT
ENTER
DEFAULT
BRIGHTNESS ALL DELETE
Sampled color Sampled color Adjusted color

2. Select the required log from 1 - 8 or ALL DELETE,
and press ENTER.
Select CHANGE to edit the log.
The cursor menu is displayed and you can readjust
the color.
Select DELETE to delete the log.
The confirmation screen will be displayed. Select OK
to delete.
When you select ALL DELETE, the "DELETE ALL
LOG." screen is displayed. Select OK to delete all
logs. The PROFILE setting will be set to NORMAL.
26 - ENGLISH
Q Saving a log setting as a profile Q Changing the profile names
Return to the COLOR MANAGEMENT menu and You can change the name of the profiles from the
save the stored log as a profile. Make sure that the PROFILE NAME CHANGE menu.
PICTURE MODE is not switched. 1. Select PROFILE NAME CHANGE and press the
1. Select the PROFILE SAVE menu and press ENTER button.
ENTER 2. Select the required profile and press the ENTER
The PROFILE SAVE menu is displayed. You can button.
save the profile as USER1, USER2 and USER3. 3. Use F G I H to specify the location of the
required character to enter and press the ENTER
USER1
button.
USER2
4. Select OK and press the ENTER button to set the
USER3
entered text as a name.
2. Press ENTER to save the profile
The confirmation screen is displayed. Press ENTER Q Loading saved profiles
again to save. When profiles are loaded under the PICTURE
3. Use F G I H to specify the location of the MODE setting, you can keep them as you defined
required character to enter and press the ENTER until the PROFILE is set to NORMAL.
button. 1. Select the required PICTURE MODE and press
You can enter up to 14 characters. ENTER.
2. Press the COLOR M. button and select the
PROFILE NAME INPUT
PROFILE menu.
The profile settings of the selected PICTURE MODE
ALL DELETE will be displayed.
3. Select the required profile and press ENTER.
Basic Operation
Return to the default setting of the
NORMAL
PICTURE MODE menu.
USER1
OK CANCEL USER2 Defined profile settings.

USER3
4. Repeat step 3 until you finish the text line.
Move cursor to ALL DELETE and press the ENTER
button to delete all the entered text line.
Press the DEFAULT button to delete the last entered NOTE:
character or indicated with cursor in the text box. • LOG and PROFILE SAVE are not displayed before
To insert a character in the entered text line, move you apply COLOR MANAGEMENT.
the cursor to the text box to select the required place • If you load a profile with a different attribute mode of
and press G then perform step 4. the profile, the CURSOR and PROFILE SAVE
5. Select OK and press the ENTER button to set the menus will not be displayed.
entered text as a name. • The approximate colors will be adjusted at the same
Press the ENTER button without entering any text to time. If you adjust the exact same color differently,
keep the default name. both colors will affect each other and you might get
unexpected results.
Q Deleting the saved profiles • White, Black and Gray are not adjustable.
You can delete the profiles from PROFILE • If you escape the COLOR MANAGEMENT menu or
DELETE menu. attempt to perform another menu action before you
save the adjusted profile, the confirmation screen will
1. Select PROFILE DELETE and press the ENTER
be displayed.
button. • If you switch the input signal before you save the
2. Select the required profile or ALL DELETE and profile, the setting will be cancelled without notice.
press the ENTER button.
The confirmation screen will be displayed and select
OK.
3. Press the ENTER button.
ENGLISH - 27
Menu Navigation
The menu system allows you to access functions which do not have their own dedicated buttons on the remote
control. The menu options are structured and categorized. You can navigate through the menu with F G H I
buttons.
Main menu and sub-menu

NOTE:
• Some default settings vary by the selected input signal.
• Sub-menu items vary according to the selected input signal.
• Some settings are adjustable without any signals.
Main menu Sub-menu Options (Underlined is default setting) Page

PICTURE PICTURE MODE NORMAL DYNAMIC COLOR1 page 31
COLOR2 CINEMA1 CINEMA2
CINEMA3
CONTRAST • Default: 0 page 31
BRIGHTNESS • Default: 0 page 31
COLOR • Default: 0 page 31
TINT • Default: 0 page 31
SHARPNESS • Default: 0 page 31
COLOR TEMPERATURE • Default: 0 page 32
DYNAMIC IRIS ON OFF page 32
WAVEFORM MONITOR OFF SINGLE LINE SCAN(Y) page 32
FULL SCAN(Y) SINGLE LINE SCAN(R)
FULL SCAN(R) SINGLE LINE SCAN(G)
FULL SCAN(G) SINGLE LINE SCAN(B)
FULL SCAN(B) MONITOR POSITION
AUTO ADJUST
SPLIT ADJUST AREA SELECT page 32
SPLIT ADJUST MODE NORMAL REVERSE
ADVANCED MENU GAMMA GAMMA HIGH • Default: 0 page 33
GAMMA MID • Default: 0
GAMMA LOW • Default: 0
CONTRAST CONTRAST R • Default: 0
CONTRAST G • Default: 0
Settings
CONTRAST R • Default: 0
BRIGHTNESS BRIGHTNESS R • Default: 0
BRIGHTNESS G • Default: 0
BRIGHTNESS B • Default: 0
COLOR MANAGEMENT PROFILE
CURSOR
LOG
PROFILE SAVE
PROFILE DELETE
PROFILE NAME CHANGE
xvYCC ON OFF
DETAIL CLARITY ON OFF
NR ON OFF
MPEG NR ON OFF
CINEMA REALITY ON OFF
TV-SYSTEM AUTO
SECAM PAL-N PAL-M
PAL NTSC 4.43 NTSC
MEMORY SAVE MEMORY1 - 16 page 34
MEMORY LOAD MEMORY1 - 16 page 34
MEMORY EDIT MEMORY DEL MEMORY NAME CHANGE page 35
SIGNAL MODE*1 page 35
*1. COMPUTER/COMPONENT/HDMI signals only
28 - ENGLISH
Menu Navigation
Main menu Sub-menu Options (Underlined is default setting) Page

POSITION H-POSITION • Default: 0 page 36
V-POSITION • Default: 0 page 36
DOT CLOCK*1 • Default: 0 page 36
CLOCK PHASE*2 • Default: 0 page 36
ASPECT 4:3 16:9 14:9 page 36
ZOOM1 ZOOM2 JUST
WSS*3 page 38
OVER SCAN*4 • Default: 0 page 38
KEYSTONE • Default: 0 page 38
AUTO SETUP*5 page 38
LENS CONTROL ZOOM/FOCUS page 39
FUNCTION BUTTON1 page 39

BUTTON BUTTON2
BUTTON3
LANGUAGE
OPTION INPUT GUIDE DETAILED SIMPLE OFF page 40

OSD DESIGN TYPE1 TYPE2 TYPE3 page 40
OSD POSITION UPPER LEFT UPPER CENTER UPPER RIGHT page 40
CENTER
Settings
LOWER LEFT LOWER CENTER LOWER RIGHT
BACK COLOR BLUE BLACK page 40
STARTUP LOGO ON OFF page 40
AUTO SEARCH ON OFF page 40
HDMI SIGNAL LEVEL NORMAL EXPAND page 40
FRAME RESPONSE NORMAL FAST page 40
INSTALLATION FRONT/DESK FRONT/CEILING page 41
REAR/DESK REAR/CEILING
SLEEP OFF 60MIN. 90MIN. 120MIN. page 41
150MIN. 180MIN. 210MIN. 240MIN.
ALTITUDE LOW HIGH page 41
LAMP POWER NORMAL ECO-MODE page 41
LAMP RUNTIME page 41
*1. COMPUTER signals only
*2. COMPUTER/COMPONENT signals only
*3. VIDEO/S-VIDEO/COMPONENT signals only
*4. Not available with COMPUTER signals
*5. COMPUTER signals only
ENGLISH - 29
Menu Navigation
Navigating through the MENU

J Displaying the main menu J Operating procedure
Press the MENU button to display the main 1. Press F G to scroll to the required main menu
menu and the operating guidance. item and press ENTER to select.
The selected item is highlighted in orange and the
sub-menu is displayed on the right.
Current See “Main menu and sub-menu” on page 28.
Main menu Sub-menu settings
PICTURE H-POSITION
POSITION V-POSITION
ASPECT
PICTURE PICTURE MODE NORMAL LANGUAGE ON
WSS
POSITION CONTRAST LENS CONTROL OVER SCAN
BRIGHTNESS KEYSTONE
LANGUAGE COLOR FUNCTION BUTTON
LENS CONTROL TINT OPTION
SHARPNESS
FUNCTION BUTTON
COLOR TEMPERATURE RETURN
OPTION DYNAMIC IRIS ON
WAVEFORM MONITOR OFF SELECT ENTER
RETURN SPLIT ADJUST
ADVANCED MENU
SELECT ENTER MEMORY SAVE
MEMORY LOAD 2. Press F G to scroll to the required sub-menu item
MEMORY EDIT
and press I H or ENTER to adjust.
The selected item is called up and the other menu
Operating guidance items disappear from the screen. Called up item will
Contains the required buttons to adjust the settings. be disappear after 5 seconds and return to the menu
mode.
J Adjusting with the bar scale If there is a lower level, the next level will be
displayed.
items
The triangle mark under the bar indicates factory PICTURE H-POSITION
default setting and the square indicates the current POSITION V-POSITION
ASPECT
setting. ENGLISH
WSS ON
LENS CONTROL OVER SCAN
Current setting KEYSTONE
FUNCTION BUTTON
OPTION
BRIGHTNESS
RETURN
Settings
Default SELECT
ENTER
J Returning to the previous menu

Press the MENU or RETURN button to return to 3. Press I H to adjust or set the selected item.
For items using a bar scale, the current settings are
the previous menu. Press repeatedly to escape
displayed on the left of the bar scale.
from the menu mode and return to the projection. You can cycle through the options of an item by
pressing I H.
BRIGHTNESS

menu.
NOTE:
• See “Resetting to the factory default settings” on page 22 to reset each menu items.
30 - ENGLISH
PICTURE menu
Remote control Control panel CONTRAST
You can adjust the contrast of the projected image.
Adjust the BRIGHTNESS in advance if necessary.
Lower Higher
See “Navigating through the MENU” on page 30.

See “Main menu and sub-menu” on page 28. Setting range: -64 to +64
PICTURE MODE BRIGHTNESS

You can adjust the brightness of the projected image.
Depending on the projection environment, you can use
these preset parameter settings to optimize image
projection. Press I H to cycle through the options. Darker Brighter
NORMAL CINEMA3
DYNAMIC
CINEMA2 COLOR
COLOR1
You can adjust the color saturation of the projected
image.
COLOR2 CINEMA1
NORMAL
Setting for a general image, such Lighter Darker
as sports or games
DYNAMIC Bright and sharp setting
Setting for HDTV standard in ITU- When COMPUTER signal is connected, only available
R BT. 709 and color temperature with the following signals.
COLOR1
6 500 K at the default setting of 1 125 (1 080)/60i 1 125 (1 080)/50i
the PICTURE menu items. 1 125 (1 080)/60p 1 125 (1 080)/50p
Setting for DCDM standard
COLOR2
(SMPTE431-2) and color
temperature 6 300 K at the TINT
Settings
default setting of the PICTURE
You can adjust the skin tone in the projected image.
menu items.
CINEMA1 Hollywood style colors
More More
CINEMA2
Deeper and more rich color
reddish greenish
setting
CINEMA3 Vivid and crisp color setting
When COMPUTER signal is connected, only available
NOTE: with the following signals.
• It may take for a while until the selected mode is 1 125 (1 080)/60i 1 125 (1 080)/50i
stabilized. 1 125 (1 080)/60p 1 125 (1 080)/50p
SHARPNESS
You can adjust the sharpness of the projected image.
Less More
sharp sharp
Setting range will vary according to the selected input

signal.
ENGLISH - 31
PICTURE menu
J AUTO ADJUST
COLOR TEMPERATURE You can switch on/off the automatic adjustment
You can adjust the white balance of the projected image. system in each items.
Items Default setting
Less More BLACK LEVEL ADJUST ON
bluish bluish
WHITE LEVEL ADJUST ON
RGB ADJUST (BLACK) OFF

RGB ADJUST (WHITE) OFF
DYNAMIC IRIS 1. Press F G and select the required item.

2. Press I H and switch on/off.
You can switch automatic adjustment of the lamp and 3. Press F G and select AUTO and press ENTER.
the lens iris on/off. The confirmation screen will be displayed.
ON: Automatic adjustment 4. Press I H and select OK.
OFF: No adjustment 5. Press ENTER.
WAVEFORM MONITOR NOTE:

• When the WAVEFORM MONITOR is set to OFF, the
You can monitor whether or not the luminance level of AUTO ADJUST is not displayed.
the input signal is in the recommended range by
displaying it in the waveform monitor. If the waveform is
not in the range, adjust it for the best quality. See
SPLIT ADJUST
“Adjusting the signal condition with a waveform” on You can perform image adjustment in some PICTURE
page 24. menu items while displaying a certain area of the frozen
image in a split window.
OFF
FULL SCAN(Y) Q SPLIT ADJUST MODE
FULL SCAN(R) Select the required split style from NORMAL and
FULL SCAN(G) REVERSE in the SPLIT ADJUST MODE menu.
FULL SCAN(B) NORMAL
SINGLE LINE SCAN(Y)
SINGLE LINE SCAN(R)
SINGLE LINE SCAN(G)
Settings
SINGLE LINE SCAN(B)

MONITOR POSITION UPPER LEFT
AUTO ADJUST
1. Press F G to move to the required waveform

style.
2. Press ENTER to select.
REVERSE
The WAVEFORM MONITOR will be displayed.
See “Adjusting the signal condition with a waveform”
on page 24.
J MONITOR POSITION
When the FULL SCAN is selected, press F G I
H to adjust the position of the monitor.
See “Adjusting the signal condition with a waveform”
on page 24.
32 - ENGLISH
PICTURE menu
Q Adjusting the image in a split window
1. Select AREA SELECT and press the ENTER ADVANCED MENU
button. You can perform more detailed image adjustment
The image will be frozen and the area cursor will be
manually.
displayed.
J GAMMA
You can adjust linear intensity at 3 levels. Press I
H to increase/decrease 1 point.
Levels Default setting
GAMMA HIGH 0
GAMMA MID 0
GAMMA LOW 0
MOVE AREA ENTER GO TO SPLIT ADJUST ENTER GO TO SPLIT ADJUST

2. Press I H to move the area cursor to select the J CONTRAST

required area and press the ENTER button. You can adjust the amount of contrast in RGB
The selected frozen image will be displayed in a split
colors individually. Press I H to increase/
window.
decrease 1 point.
3. Press the MENU to display the PICTURE menu on
the right. RGB Default setting
CONTRAST R 0
PICTURE PICTURE MODE NORMAL
CONTRAST G 0
POSITION CONTRAST
BRIGHTNESS
LANGUAGE COLOR
LENS CONTROL TINT
SHARPNESS
FUNCTION BUTTON
CONTRAST B 0
COLOR TEMPERATURE
OPTION DYNAMIC IRIS ON
WAVEFORM MONITOR OFF
RETURN SPLIT ADJUST

ADVANCED MENU
MEMORY SAVE
SELECT ENTER
MEMORY LOAD
MEMORY EDIT
J BRIGHTNESS
You can adjust the brightness in RGB colors
individually. Press I H to increase/decrease
1 point.
4. Adjust the required PICTURE menu items. RGB Default setting
The Other menu items are not available.
BRIGHTNESS R 0
Sub-menu items vary according to the selected input
signal. See “Main menu and sub-menu” on page 28. BRIGHTNESS G 0
Settings
5. Press MENU/RETURN button several times to
escape from the menu. BRIGHTNESS B 0
6. Press the ENTER button. Setting range: -16 to +16
to finish the adjustment.
J NR (Noise Reduction)
7. Press the ENTER button. You can switch the automatic noise reduction
Press the ENTER button again to return to the AREA system on/off. Press I H to select the required
SELECT. setting.
Press the RETURN button escape from the SPLIT ON: Automatic noise reduction
ADJUST mode. OFF: No noise reduction
J MPEG NR
You can switch the automatic noise reduction
system for MPEG format images on/off. The
system minimize block noise and mosquito noise
to eliminate jagged edges, providing an overall
smoother image. Press I H to select the required
setting.
ON: Active
OFF: Deactive
NOTE:
• MPEG NR system is not available with COMPUTER/
HDMI (VGA60) signals.
ENGLISH - 33
PICTURE menu
J COLOR MANAGEMENT
You can manage your own defined color settings.
MEMORY SAVE
See “Setting your own color profile” on page 26. You can save and name the adjusted PICTURE menu
settings for instant access from MEMORY LOAD menu.
J xvYCC 1. Adjust the items in PICTURE menu.
You can switch on/off the automatic adjustment 2. Select MEMORY SAVE and press the ENTER
system for signals which complied with xvYCC. button.
ON: Active 3. Select the required memory setting and press the
OFF: Deactive ENTER button.
NOTE: and press the ENTER button.
• xvYCC adjustment system is only available with HDMI Indicated with ★ is in use, and ✩ is empty.
signals in COLOR1 of PICTURE MODE menu. 4. Use F G I H to specify the location of the
J DETAIL CLARITY button.
You can switch on/off the automatic detail clarity You can enter up to 16 characters.
system. MEMORY NAME INPUT
ON: Active
OFF: Deactive
J CINEMA REALITY ALL DELETE
You can switch the automatic image synchronizer

on/off for 24 frames a second images, such as
movies. Press I H to select the required setting.
ON: Active
OFF: Deactive
OK CANCEL
NOTE: 5. Repeat step 4 until you finish the text line.

• CINEMA REALITY is effective only with interlace Move the cursor to ALL DELETE and press the
signals. ENTER button to delete all the entered text line.
Press the DEFAULT button to delete the last entered
J TV-SYSTEM character or indicated with cursor in the text box.
When the video signal is changed, the setting To insert a character in the entered text line, move
switches automatically. the cursor to the text box to select the required place
You can switch the setting manually to match the and press G then perform step 4.
video data. Press I H to cycle through the 6. Select OK and press the ENTER button to set the
Settings
options. entered text as a name.

AUTO NTSC
NOTE:
• If you leave the text box empty and save, the default
SECAM
memory number will stay as a name.
NTSC 4.43
PAL-N
MEMORY LOAD
PAL-M PAL You can access the saved settings instantly. See
“Loading a saved setting” on page 23.
1. Select a setting from MEMORY1 - 16.
NOTE: Undefined settings will not be selectable.
• AUTO setting will select from NTSC/NTSC 4.43/PAL/
2. Press ENTER to activate.
PAL60/PAL-M/PAL-N/SECAM.
NOTE:
• If you have not saved any settings, MEMORY1 - 16 will
not be displayed.
34 - ENGLISH
PICTURE menu
MEMORY EDIT SIGNAL MODE

You can edit the named memory settings. The current selected signal will be displayed. This is
available with signals from COMPUTER IN/
Q Deleting a memory setting COMPONENT IN/HDMI IN only.
1. Select MEMORY DEL and press the ENTER
button.
NOTE:
2. Select the required memory setting and press the
• See “List of compatible signals” on page 47.
ENTER button.
If you select ALL DELETE, you can delete all of the
saved memory settings.
3. Select OK in the confirmation screen and press the
ENTER button.
Q Changing the name of the memory
setting
1. Select the required memory setting and press the
ENTER button.
2. Use F G I H to specify the location of the
button.
You can enter up to 16 characters.
MEMORY NAME INPUT
ALL DELETE
OK CANCEL
3. Repeat step 4 until you finish the text line.

Move the cursor to ALL DELETE and press the
ENTER button to delete all the entered text line.
Settings
Press the DEFAULT button to delete the last entered
character or indicated with cursor in the text box.
To insert a character in the entered text line, move
the cursor to the text box to select the required place
and press G then perform step 4.
4. Select OK and press the ENTER button to set the
entered text as a name.
NOTE:
• If you have not saved any settings, MEMORY1 - 16 will
not be displayed.
ENGLISH - 35
POSITION menu
Remote control Control panel CLOCK PHASE
If you require further adjustment for the same reason as
the DOT CLOCK adjustment, you can fine adjust the
timing of the clock. Press I H to adjust. (Available with
signals from COMPUTER IN/COMPONENT IN only)
See “Navigating through the MENU” on page 30.

NOTE:
See “Main menu and sub-menu” on page 28. • If the projecting signal’s dot clock frequency is higher
than 150 MHz, the adjustment may not make a
difference.
H-POSITION • Available signals from COMPONENT IN:
1 125 (1 080)/60i, 1 125 (1 080)/50i, 1 125 (1 080)/60p,
You can move the projected image horizontally for fine 1 125 (1 080)/50p, 1 125 (1 080)/24p, 750 (720)/60p
adjustment.
Move left Move ASPECT

right You can switch the aspect ratio manually when needed.
J Aspect ratio depend on signals
Press I H to cycle through the aspect ratio
V-POSITION options. The cycle pattern depends on the
You can move the projected image vertically for fine connected signals.
adjustment.
4:3 \ 16:9 \ 14:9 \ ZOOM1 \
Move Move up VIDEO/ ZOOM2 \ JUST
S-VIDEO AUTO \ 4:3 \ 16:9 \ JUST \ ZOOM
down NTSC signal
4:3 \ 16:9
4:3 \ 16:9
DOT CLOCK COMPUTER
(RGB)
VGA or SVGA signals
Not switchable
If you have interference patterns of the projected image, WIDE480/600/720/768/768-2/800/900
which is sometimes referred to as moire or noise, you signals
can minimize it by pressing I H to adjust the clock 4:3 \ 16:9
frequency. (Available with signals from COMPUTER IN 16:9 \ H - FIT \ V - FIT \ ZOOM
Settings
only) 1 125 (1 080)/50i, 1 125 (1 080)/60i,

1 125 (1 080)/50p, 1 125 (1 080)/60p,
HDMI
1 125 (1 080)/24p, 750 (720)/50p and
750 (720)/60p signals
4:3 \ 16:9 \ JUST \ ZOOM
525p (480p) and 625p (576p) signals
4:3 \ 16:9 \ 14:9 \ JUST \ ZOOM1
NOTE: \ ZOOM2
• If the projecting signal’s dot clock frequency is higher 625i (576i), 625p (576p)
than 150 MHz, the adjustment may not make a AUTO \ 4:3 \ 16:9 \ JUST \ ZOOM
difference. COMPONENT 525i (480i), 525p (480p)
• DOT CLOCK needs to be adjusted before adjusting the (YPBPR) 16:9 \ H - FIT \ V - FIT
CLOCK PHASE. 1 125 (1 080)/50i, 1 125 (1 080)/60i,
1 125 (1 080)/50p, 1 125 (1 080)/60p,
1 125 (1 080)/24p, 750 (720)/50p,
750 (720)/60p signals
36 - ENGLISH
POSITION menu
J Aspect ratio options and projection example
If you apply the aspect ratio options to the projected image, the result will be as follows. The result may differ
due to the input signals. See “Switching the aspect ratio” on page 23.
Q VIDEO/S-VIDEO/COMPONENT
Not available with 1 125 (1 080)/50i, 1 125 (1 080)/60i, 1 125 (1 080)/50p, 1 125 (1 080)/60p, 1 125 (1 080)/
24p, 750 (720)/50p and 750 (720)/60p signals.
Squeeze 16:9 14:9 2.35:1
4:3
signal Letter box Letter Box Cinescope
Original size
4:3 Projects at 4:3.
16:9 Adjusts horizontally to 16:9.
Adjusts horizontally to fit 16:9. Closer

JUST to edge, more enlarged. Not available
with COMPUTER signals.
Adjusts to 16:9 size with preserving
ZOOM/
original ratio. Escape the menu mode
ZOOM1
and press FG to adjust vertically.
Adjusts to cinescope size not
including letter box. Escape the menu
ZOOM2
mode and press FG to adjust
vertically.
14:9 Adjusts to 14:9.
Q COMPONENT signals
Available with 1 125 (1 080)/50i, 1 125 (1 080)/60i, 1 125 (1 080)/50p, 1 125 (1 080)/60p, 1 125 (1 080)/24p,
750 (720)/50p and 750 (720)/60p signals
Settings
4:3 16:9 Cinescope
Original Size
H - FIT Adjusts horizontally to 16:9.
Adjusts to 16:9 vertically. Escape and press F G to scroll

V - FIT
the image to adjust the edge vertically.
Adjusts to 16:9 size with preserving original ratio. Escape

ZOOM
the menu mode and press FG to adjust vertically.
ENGLISH - 37
POSITION menu
WSS KEYSTONE
WSS (Wide Screen Signalling) detects if a PAL/ If the projector is aligned non-perpendicularly to the
625p (576p)/625i (576i) signal is input and that signal screen, or if the projection screen has an angled surface,
has an identification signal, and switch the aspect ratio you can vertically correct keystone.
to required setting automatically. You can switch the
system off manually. Image Operation
OVER SCAN
If the 4 edges of an image is partly dropped, you can use
this function to adjust and project it properly.
Setting range: 0 to +10
OVER SCAN is not available with COMPUTER
signals.
Shrink Enlarge Setting range: -32 to 32
NOTE:
• You can correct the distortion ± 30 degrees from the
vertical plane. For a better quality image, installing the
projector with a minimum of distortion is recommended.
• Some distortion may be retained for the lens shift
adjustment.
• The distortion of the main menu screen is not
correctable.
• The result of the keystone correction will affect the
aspect ratio and the size of the image.
AUTO SETUP
You can adjust V - POSITION, H - POSITION, DOT
CLOCK and CLOCK PHASE automatically when
connecting via COMPUTER IN. Press ENTER to adjust
these at the same time.
Settings
38 - ENGLISH
LENS CONTROL FUNCTION BUTTON
Remote control Control panel Remote control Control panel
See “Navigating through the MENU” on page 30. See “Navigating through the MENU” on page 30.
See “Main menu and sub-menu” on page 28. See “Main menu and sub-menu” on page 28.
ZOOM/FOCUS BUTTON1/2/3
You can use the 2 different test patterns to adjust the You can assign certain menu options to the 3 function
focus and zoom of the image. See “Lens shift and buttons for instant operation.
positioning” on page 16. 1. Select the required button from BUTTON1,
1. Press ENTER to display test pattern 1. BUTTON2 or BUTTON3 and press the ENTER
Press F G to adjust the focus and I H to adjust button.
the zoom. 2. Press F G I H to select the required menu
options and press the ENTER button.
HDMI 1 IN NORMAL
HDMI 2 IN DYNAMIC
RETURN FOCUS HDMI 3 IN COLOR1
ZOOM
ENTER
COMPUTER IN COLOR2
2. Press ENTER to display test pattern 2. COMPONENT 1 IN CINEMA1
Press F G to adjust the focus and I H to adjust
COMPONENT 2 IN CINEMA2
the zoom.
S-VIDEO IN CINEMA3
VIDEO IN SPLIT ADJUST
WAVEFORM AUTO
BLANK
ADJUST
RETURN FOCUS
AUTO SETUP MEMORY LOAD
CONTRAST BRIGHTNESS
ZOOM
ENTER
3. Press ENTER to display the projected image. CONTRAST R BRIGHTNESS R
Settings
You can confirm the adjustment is fit to the projected CONTRAST G BRIGHTNESS G
image.
CONTRAST B BRIGHTNESS B
menu, or press repeatedly to escape the menu Q BLANK function
mode. You can stop the projection temporary for electrical
power save. Press any button except the LIGHT
NOTE: and learning remote control buttons.
• When the projector and/or the screen is tilted, adjust
the focus at the center of the image. The upper and
lower edge might be out of focus.
• When the image is distorted in keystone, adjust the
KEYSTONE in POSITION menu.
ENGLISH - 39
OPTION menu
Remote control Control panel BACK COLOR
You can choose a screen color from BLUE or BLACK
for when the projector is in idle. Press I H to select.
STARTUP LOGO
You can switch the logo on/off that is displayed when
See “Navigating through the MENU” on page 30. starting up the projector. Press I H to select the
See “Main menu and sub-menu” on page 28. required option. STARTUP LOGO will be displayed for
30 seconds.
INPUT GUIDE ON
OFF
Active
Deactive
When you change the input method, the guidance
appears in the upper right corner of the screen. The AUTO SEARCH
following display methods are available. Press I H to
cycle through the options. When the projector is turned on, the input terminals are
detected and an input signal is selected automatically.
Options Function You can switch the system on/off. Press I H to cycle
through the options.
OFF Turn off the guidance. ON Active
Display the input method by text. The OFF Deactive
SIMPLE INPUT GUIDE will go out after
5 seconds without any operation. NOTE:
Display the input method by graphic. The • When no signal is detected, the last used input will be
DETAILED INPUT GUIDE will go out after selected.
10 seconds without any operation.
HDMI SIGNAL LEVEL

OSD DESIGN When an HDMI IN is selected, you can switch the HDMI
You can change the background color of the menu. signal NORMAL or EXPAND to display the image. Press
Press I H to cycle through the options. I H to select an option.
TYPE1 Semi transparent black NORMAL For general HDMI equipment
TYPE2 Solid blue EXPAND For HDMI equipment with expanded
TYPE3 Semi transparent dark blue signals.
Settings
OSD POSITION NOTE:

• HDMI SIGNAL LEVEL is not available with some
You can change the position where to display the menu. equipment.
Press I H to cycle through the options.
UPPER UPPER UPPER FRAME RESPONSE

LEFT CENTER RIGHT
You can minimize the time delay of image displaying for
the interlace signals.
CENTER NORMAL Prioritize the image quality
FAST Prioritize the frame response
LOWER LOWER LOWER

LEFT CENTER RIGHT
40 - ENGLISH
OPTION menu
INSTALLATION ALTITUDE
When installing the projector, select the projection If you use the projector at high elevation, the ALTITUDE
method according to the projector position. Press I H setting need to be HIGH to set the fan speed high. Press
to cycle through the options. See “Projection method” on I H to select the required option.
page 15. LOW The fan speed is low.
HIGH The fan speed is high.
Setting on a desk/floor and
FRONT/DESK
projecting from front NOTE:
Mounting in the ceiling and • At 1 400 m (4 593 ft) above sea level, the setting must
FRONT/CEILING
projecting from front be HIGH.
• The loudness of fan noise depends on the ALTITUDE
Setting on a desk/floor and
REAR/DESK setting.
projecting from rear
REAR/CEILING
Mounting in the ceiling and
projecting from rear
LAMP POWER
You can adjust the power of the lamp to save on
SLEEP electricity, prolong the lamp life and reduce the noise.
Options Function
You can select the required duration of time and set the
off timer to turn off the power of the projector When higher luminance is
NORMAL
automatically. 3 minutes before turn-off, the countdown required.
of minutes will be displayed in the lower right corner. When lower luminance is
ECO-MODE
Press I H to cycle through the options. See “Switching sufficient.
off the projector automatically” on page 25.
NOTE:
• When no input signal is detected, the function is
disabled.
LAMP RUNTIME
You can check how long the lamp has been used.
NOTE:
• LAMP RUNTIME is a relevant matter for lamp
Settings
replacement timing. See “Replacing the lamp unit” on
page 44.
ENGLISH - 41
TEMP and LAMP Indicators
Managing the indicated problems
If a problem should occur with the projector, the LAMP and/or TEMP
indicators will inform you. Manage the indicated problems as follow.
1. Confirm the status of all indicators and projector, and switch off
the projector in proper way.
2. Find out the cause of the problem by status of the LAMP and/or
TEMP indicators. POWER LAMP TEMP
3. Follow the following instruction for each indication and solve the
problem.
4. Turn on the projector in the correct way and confirm the
indicator is not indicating a problem any longer.
NOTE:
• If no problem is found or the problem remains, do not turn on the projector. Instead contact an Authorized Service Center.
J LAMP indicator
Indicator Illuminating red Flashing red
LAMP RUNTIME has

Problem The lamp circuit failure, abnormal function or lamp unit is damaged.
reached 1 800 hours.
The MAIN POWER is
The lamp unit will run
switched on again The lamp circuit failure, The lamp unit is
Cause out soon and needs to
before the lamp unit is abnormal function. damaged.
be replaced.
cooled enough.
Let the lamp unit cool
See “Replacing the Contact an Authorized See “Replacing the
Remedy down and turn on the
lamp unit” on page 44. Service Center. lamp unit” on page 44.
MAIN POWER.
J TEMP indicator
Illuminating red and still projecting
Indicator
Flashing red and the POWER button is turned off
Problem The temperature inside and/or outside the projector is abnormally high.
The air filter is The projector is located
The ventilation The room temperature
Cause excessively dirty and at high elevations
openings are covered. is too high.
the ventilation is poor. (above 1 400 m).
Remove the object(s) Reinstall the projector Turn on the projector
Replace the air filter in
from the ventilation in temperature and set the ALTITUDE
Remedy the proper method.
openings or clear controlled place. See to HIGH.
See page 43.
around the projector. page 52. See page 41.
Maintenance
42 - ENGLISH
Care and Replacement
Cleaning the projector
J Before cleaning the projector
Switch off the MAIN POWER switch in proper way and disconnect the power plug from the wall outlet.
Unplug all the cables from the projector.
J Cleaning the outer surface of the projector

Wipe off dirt and dust gently with a soft cloth.
If it is difficult to remove the dirt, soak a cloth in a neutral detergent diluted with water, wring the cloth well and then wipe
the projector. Dry off the projector with dry cloth.
If you use a chemical treated wipe, follow the instructions supplied with it.
J Cleaning the lens surface

Wipe off dirt and dust gently with a lint-free cloth.
Make sure no dirt or dust remains on the surface of the lens. It will be enlarged and projected onto a screen.
J Cleaning the air filter

If the air filter is excessively dirty, the internal temperature of the projector increases and may cause
malfunction. Clean the air filter regularly every 100 hours of usage.
1. Place a finger at the bottom of the air filter
2. Slightly push up and pull out the air filter to remove.
3. Vacuum dirt and dust from the air filter.
Do not wash the air filter.

4. Place and slightly slide in the air filter in the air intake port to attach.
Make sure the air filter clicks into the place.
NOTE:
• Do not use the projector without attaching the air filter.
J Replacing the air filter

Maintenance
The air filter should be replaced when cleaning is ineffective and when replacing the lamp unit. A replacement
air filter is provided with a replacement lamp unit, ET-LAE1000. Contact an Authorized Service Center for the
optional air filter.
ENGLISH - 43
Replacing the lamp unit

J Before replacing the lamp unit
Switch off the MAIN POWER button in proper way and disconnect the power plug from the wall outlet.
Make sure the lamp unit and the surroundings are cooled enough.
Unplug all the cables from the projector.
Prepare a Phillips-head screwdriver.
Contact an Authorized Service Center to purchase a replacement lamp unit (ET-LAE1000).
When the projector is mounted in the ceiling, do not work directly under the projector or put your face closer to the
projector.
NOTE:
• Prior to replacing the lamp unit, allow it to cool down to prevent the risk of burns, damage and other hazards.
• Do not attempt replacement with an unauthorized lamp unit.
J When to replace the lamp unit

The lamp unit is consumable and the brightness decreases by duration of usage. The LAMP indicator will
inform you of the replacement timing at 1 800 hours, and at 2 000 hours, the projector will be turned off. Those
figures are rough guidance and might be shortened by the usage conditions, characteristics of the lamp unit,
environmental conditions, and so on. You can check the duration of usage time using LAMP RUNTIME in the
OPTION menu.
On screen LAMP indicator
REPLACE LAMP
Indication
“REPLACE LAMP” is displayed on the upper left

of the screen for 30 seconds.
Over 1 800 hours
To clear the screen immediately, press any
button. Illuminates red.
“REPLACE LAMP” is displayed on the upper left
Over 2 000 hours of the screen, and it will stay until you respond.
To clear the screen, press any button.
NOTE:
• The guide times, 1 800 and 2 000 hours, are rough estimates based on certain conditions and is not a guaranteed time.
The estimated condition is: LAMP POWER in OPTION menu set to NORMAL.
• To prolong the lamp life, set the LAMP POWER in OPTION menu to ECO-MODE. See “LAMP POWER” on page 41.
• For more information about the lamp unit, such as guaranteed time, see the instructions which is provided with the lamp
unit.
J Opening the top cover

Maintenance
1. Hold at the back corner of the top cover and

slightly push up to open.
2. Unhook the top cover safety hook from the
projector.
3. Hold the top cover up and press one of the buttons
of the hinge parts each to remove.
When the projector is mounted in the ceiling,
removing the hinge parts is not required.
4. Remove the top cover aside.
Press here
NOTE: When the projector is mounted in Top cover safety hook Hinge parts
the ceiling;
• Place yourself at back side of the projector, then open
and close the top cover.
• Do not work directly under the projector or put your face
closer to the projector.
44 - ENGLISH
J Removing and replacing the lamp unit
1. Use a Phillips screw driver to loosen the 3 lamp unit fixing
screws until the screws turn freely. Lamp unit
2. Hold the handle of the lamp unit and release the lamp unit lock. fixing screws
3. Pull out the lamp unit gently from the projector.
Lamp unit lock

4. Replace the new lamp unit while making sure that the direction
of insertion is correct. Press here Press here
Press the top of the lamp unit and make sure the unit is installed securely.
5. Tighten the lamp unit fixing screws securely with a Phillips screwdriver.
J Attaching the top cover
1. Attach the hinge parts of the top cover to the projector and press slightly until it
clicks.
When the projector is mounted in the ceiling, attaching the hinge parts is not required.
2. Hook the top cover safety hook to the projector.
3. Hooking the tabs of the top cover to the front of the projector and lift down slowly.
4. Press the back corner of the top cover gently until it clicks.
Make sure to hook the top cover safety hook to the body.
NOTE:
• Be sure to install the lamp unit and the top cover of the projector securely. If they are not
securely installed, it may cause the protection circuit to operate so that the power cannot be
turned on.
• Grip the handle and keep the lamp unit paralleled when you remove the lamp unit. Some parts
of the lamp unit are sharpened and may cause injury.
• Do not switch the power on while the top cover is opened.
• When the projector is mounted in the ceiling, keep the lamp unit paralleled up and remove.
J Resetting the LAMP RUNTIME

If the lamp usage time has passed 2 000 hours (when LAMP POWER has been set to NORMAL), the
projector will switch to standby mode after approximately 10 minutes of operation. The resetting procedure
should thus be completed within 10 minutes.
1. Connect the power cord to the projector and a wall 6. Press and hold the ENTER button for
outlet, and switch the MAIN POWER on. approximately 3 seconds.
2. Switch the POWER button. 7. The confirmation screen will be displayed and
3. Press the MENU button to display the menu. select OK.
4. Press F G to select OPTION and press ENTER. 8. Switch off the POWER button to reset the duration
5. Press F G to select LAMP RUNTIME. of the LAMP RUNTIME.
Maintenance
SLEEP OFF
ALTITUDE LOW
9. Confirm the duration of time in LAMP RUNTIME is
LAMP POWER NORMAL reset to "0".
LAMP RUNTIME 1820H
ENGLISH - 45
Troubleshooting
Should any problem persist, contact your dealer.
Reference
Problem Cause
page
The power cord may not be connected. 19
The MAIN POWER switch is turned off. 20
No electric supply is at the wall outlet. 19
Power does not turn on. TEMP indicator is lit or flashes. 42
LAMP indicator is lit or flashes. 42
The lamp unit cover has not been securely installed. 44
The circuit breakers have tripped. -
The video signal input source may not be connected to a terminal 18
properly.
The input selection setting may not be correct. 23
No picture appears.
The BRIGHTNESS adjustment setting may be at the minimum setting. 31
The SHUTTER function may be in use. 39
The lens cover may still be attached to the lens. 12
The lens focus may not have been set correctly. 21
The projector may not be at the correct distance from the screen. 14
The picture is fuzzy.
The lens may be dirty. 10
The projector may be tilted too much. 16
COLOR or TINT adjustment may be incorrect. 31
The color is pale or grayish. The input source which is connected to the projector may not be 28
adjusted correctly.
The batteries may be weak. -
The batteries may not have been inserted correctly. 11
The Remote control does
The remote control signal receptor on the projector may be 22
not operate. obstructed.
The remote control unit may be out of the operation range. 22
The signal format (TV-SYSTEM) may not have been set correctly. 34
The picture does not
There may be a problem with the VCR or other signal source. -
display correctly. A signal which is not compatible with the projector is being input. 47
The cable may be longer than the optional cable. -
The external video output from a laptop computer may not be correct. 48
Picture from a computer (You may be able to change the external output settings by pressing
does not appear. the [Fn] + [F3] or [Fn] + [F10] keys simultaneously. The actual method
varies depending on the type of computer; refer to the documentation
provided with your computer for further details.)
Maintenance
46 - ENGLISH
Technical Information
List of compatible signals
Scanning
Display frequency Dot clock Picture
Mode Display resolution frequency Terminals
H quality*2
(dots)*1 V (Hz) (MHz)
(kHz)
NTSC/NTSC 4.43/
- 720 x 480i 15.7 59.9 - A
PAL-M/PAL60 VIDEO/S-VIDEO
PAL/PAL-N/SECAM - 720 x 576i 15.6 50.0 - A
525i (480i) 525i 720 x 480i 15.7 59.9 13.5 A
COMPONENT
625i (576i) 625i 720 x 576i 15.6 50.0 13.5 A
525p (480p) 525p 720 x 483 31.5 59.9 27.0 A
COMPONENT/HDMI
625p (576p) 625p 720 x 576 31.3 50.0 27.0 A
1 125 (1 080)/60i 1 125/60i 1 920 x 1 080i 33.8 60.0 74.3 AA COMPONENT/
1 125 (1 080)/50i 1 125/50i 1 920 x 1 080i 28.1 50.0 74.3 AA HDMI/COMPUTER
1 125 (1 080)/24p 1 125/24p 1 920 x 1 080 27.0 24.0 74.3 AA COMPONENT/HDMI
1 125 (1 080)/60p 1 125/60p 1 920 x 1 080 67.5 60.0 148.5 AA COMPONENT/
1 125 (1 080)/50p 1 125/50p 1 920 x 1 080 56.3 50.0 148.5 AA HDMI/COMPUTER
750 (720)/60p 750/60p 1 280 x 720 45.0 60.0 74.3 AA
COMPONENT/HDMI
750 (720)/50p 750/50p 1 280 x 720 37.5 50.0 74.3 AA
VGA480 VGA60 640 x 480 31.5 59.9 25.2 A
VGA75 640 x 480 37.5 75.0 31.5 A
VGA85 640 x 480 43.3 85.0 36.0 A
VGA138 640 x 480 72.1 138.0 62.3 A
WIDE480 WIDE480 856 x 480 30.1 60.1 31.5 A
SVGA SVGA55 800 x 600 35.2 56.3 36.0 A
SVGA60 800 x 600 37.9 60.3 40.0 A
SVGA70 800 x 600 48.1 72.2 50.0 A
SVGA75 800 x 600 46.9 75.0 49.5 A
SVGA85 800 x 600 53.7 85.1 56.3 A
WIDE600 WIDE600 1 072 x 600 37.2 59.9 51.4 A
WIDE720 WIDE720 1 280 x 720 45.1 60.1 76.5 AA
XGA XGA60 1 024 x 768 48.4 60.0 65.0 A COMPUTER
XGA70 1 024 x 768 56.5 70.1 75.0 A
XGA75 1 024 x 768 60.0 75.0 78.8 A
XGA85 1 024 x 768 68.7 85.0 94.5 A
XGA89 1 024 x 768 72.1 89.0 99.2 A
WIDE768 WIDE768 1 280 x 768 45.3 56.5 76.2 A
MXGA MXGA70 1 152 x 864 64.0 71.2 94.2 A
MXGA75 1 152 x 864 67.5 74.9 108.0 A
SXGA SXGA60 1 280 x 1 024 64.0 60.0 108.0 A
SXGA60+ SXGA60+ 1 400 x 1 050 65.1 59.9 122.4 A
WIDE768-2 WIDE768-2 1 360 x 768 48.8 59.8 74.3 A
WIDE800 WIDE800 1 280 x 800 49.7 59.8 83.5 A
WIDE900 WIDE900 1 440 x 900 55.9 59.8 106.5 A
*1. The “i” appearing after the resolution indicates an interlaced signal.
*2. The following symbols are used to indicate picture quality.
AA Maximum picture quality can be obtained.
A Signals are converted by the image processing circuit before picture is projected.
Appendix
ENGLISH - 47
Serial terminal
The serial connector which is on the connector panel of the projector conforms to the RS-232C interface
specification, so that the projector can be controlled by a personal computer which is connected to this connecter.
J Connection
D-sub 9 pin (male)
Serial terminal (female)

Computer
NOTE:
• You must use only an RS-232C Serial Interface Cable with a ferrite core, type ET-ADSER.
J Pin assignments and signal names
Pin No. Signal name Contents

A NC
B TXD Transmitted data
C RXD Received data
D NC
E GND Earth
F NC
G RTS
Connected internally
H CTS
I NC
J Cable specifications NC NC
(When connected to a personal computer)

PC (DTE)
NC NC
Projector
NC NC
NC NC
J Basic format
STX Command : Parameter ETX The data streaming from the computer will
start with STX, and proceed to Command,
Start byte 1 byte End Parameter and end with ETX. You can
3 bytes 1 byte -
(02h) (03h) add the required parameter.
4 bytes
The projector can not receive any command for 10 seconds after the lamp is switched on. Wait 10 seconds
before sending the command.
Appendix
If sending multiple commands, check that a response has been received from the projector for one
command before sending the next command.
When a command which does not require parameters to be sent, the colon (:) is not required.
If an incorrect command is sent from the personal computer, the ER401 command will be sent from the
projector to the personal computer.
48 - ENGLISH
J Communication settings
Signal level RS-232C Character length 8 bits
Sync. method Asynchronous Stop bit 1 bit
Baud rate 9 600 bps X parameter None
Parity None S parameter None
J Control commands
Command Control contents Remarks

In standby mode, all commands other than the PON command are ignored.
PON POWER ON
The PON command is ignored during lamp ON control.
If a PON command is received while the cooling fan is operating after the lamp has switched
POF POWER OFF
off, the lamp is not turned back on again straight away in order to protect the lamp.
Parameter:
CP1 = COMPONENT1 IN CP2 = COMPONENT2 IN
IIS INPUT SVD = S-VIDEO IN VID = VIDEO IN
HD1 = HDMI1 IN HD2 = HDMI2 IN
HD3 = HDMI3 IN RG1 = COMPUTER IN
OMN MAIN Displaying the main menu.
OEN ENTER Activating the selected items in the menu mode.
OBK RETURN Returning to the previous menu or escaping from the menu mode.
OCU/OCD/ OCU = F button OCL = I button

Navigation buttons
OCL/OCR OCD = G button OCR = H button
OLE LENS Activating the LENS CONTROL menu.
OST DEFAULT Resetting to the factory default setting. (page 22)

Freezing the projected screen.
OFZ FREEZE Parameter:
0 = OFF 1 = ON
Setting the duration of time to turn off the power automatically. (page 25)
OOT SLEEP 0 = OFF 1 = 60min. 2 = 90min. 3 = 120min. 4 = 150min.
5 = 180min. 6 = 210min. 7 = 240min.
Turning off the projection temporarily.
OSH BLANK Send the command to switch between ON and OFF.
Do not send the command consecutively.
OVM PICTURE Activating the PICTURE menu. Send the command to switch menu items. (page 25)
Activating the WAVEFORM. (page 24)
Parameter:
0 = OFF
OWM WAVEFORM 1 = FULL SCAN (Y) 5 = SINGLE LINE SCAN (Y)
2 = FULL SCAN (R) 6 = SINGLE LINE SCAN (R)
3 = FULL SCAN (G) 7 = SINGLE LINE SCAN (G)
4 = FULL SCAN (B) 8 = SINGLE LINE SCAN (B)
VS1 ASPECT Switching the aspect ratio. (page 23)
Switching the PICTURE MODE. (page 25)
Parameter:
VPM PICTURE MODE
NOR = NORMAL DYN = DYNAMIC CL1 = COLOR1 CL2 = COLOR2
CN1 = CINEMA1 CN2 = CINEMA2 CN3 = CINEMA3
Appendix
ENGLISH - 49
J Inquiry commands
Command Control contents Parameter
QPW Power status 000 = OFF 001 = ON
QFZ FREEZE status 0 = OFF 1 = ON

CP1 = COMPONENT1 IN CP2 = COMPONENT2 IN
SVD = S-VIDEO IN VID = VIDEO IN
QIN INPUT signal status
HD1 = HDMI1 IN HD2 = HDMI2 IN
HD3 = HDMI3 IN RG1 = COMPUTER IN
0 = OFF 1 = 60min. 2 = 90min. 3 = 120min. 4 = 150min.
QOT SLEEP status
5 = 180min. 6 = 210min. 7 = 240min.
NOR = NORMAL DYN = DYNAMIC CL1 = COLOR1 CL2 = COLOR2
QPM PICTURE MODE status
CN1 = CINEMA1 CN2 = CINEMA2 CN3 = CINEMA3
QSH BLANK status 0 = OFF
Parameter:
0 = OFF
1 = FULL SCAN (Y) 5 = SINGLE LINE SCAN (Y)
QWM WAVEFORM status
2 = FULL SCAN (R) 6 = SINGLE LINE SCAN (R)
3 = FULL SCAN (G) 7 = SINGLE LINE SCAN (G)
4 = FULL SCAN (B) 8 = SINGLE LINE SCAN (B)
Appendix
50 - ENGLISH
Ceiling mount bracket safeguards

The projector and the ceiling mount bracket are designed sufficiently safety though, make sure the safety cable
provided with the projector is installed and attached to the bottom of the projector when mounting in the ceiling for
safety and security.
NOTE:
• Even if it is guarantee period, the manufacturer is not responsible for any hazard or damage caused by using a ceiling
mount bracket which is not purchased from an authorized distributors, or environmental conditions.
• Make sure to use a torque driver and do not use an electrical screwdriver or an impact screwdriver.
• Installation work of the ceiling mount bracket should only be carried by a qualified technician.
• Remove an unused ceiling mount bracket promptly.
J Installing the safety cable

1. Install the ceiling mount bracket according to the Installation Instructions.
2. Loop the security cable around the ceiling mount bracket with less slack.
Lace the cable of the end with a latch through the loop on the other end of the cable.
3. Attach the latch on to the bottom of the projector with a provided screw.
Torque: 1.25±0.2 N·m
* Indicated above is ET-PKE1000S.
Appendix
ENGLISH - 51
Specifications
Power supply AC 100 - 240 V 50 Hz/60 Hz
240 W
Power consumption
During standby (when fan is stopped): 0.08 W
Amps 2.8 A - 1.2 A
Panel size (diagonal) 0.74 type (17.78 mm)
Aspect ratio 16 : 9
LCD panel Display method 3 transparent LCD panels (RGB)
Drive method Active matrix method
Pixels 2 073 600 (1 980 x 1 080) x 3 panels
Manual zoom (2x)/Manual focus
Lens
F 1.9 - 3.2, f 22.4 mm - 44.8 mm
Lamp UHM lamp (165 W)
Luminosity 1 500 lm
0 °C - 40 °C (32 °F - 104 °F)
When the ALTITUDE (page 41)
Temperature
Operating environment is set to ON: 0 °C - 35 °C (32 °F -
95 °F)
Humidity 20% - 80% (no condensation)
Horizontal scanning
30 kHz - 70 kHz
frequency
Scanning
frequency*1 Vertical scanning
50 Hz - 85 Hz
(for RGB signal) frequency
Dot clock frequency Less than 150 MHz
525i (480i), 525p (480p), 625i (576i), 625p (576p), 750 (720)/60p,
COMPONENT (YPBPR) signals 750 (720)/50p, 1 125 (1 080)/60i, 1 125 (1 080)/50i,
1 125 (1 080)/60p, 1 125 (1 080)/50p, 1 125 (1 080)/24p
Color system 7 (NTSC/NTSC 4.43/PAL/PAL-M/PAL-N/PAL60/SECAM)
Projection size 40" - 200" (1 016 mm - 5 080 mm)
Throw distance 1.2 m - 12 m (3'11" - 39'4")
Screen aspect ratio 16 : 9
FRONT/DESK, FRONT/CEILING, REAR/DESK, REAR/CEILING
Installation
(Menu selection method)
*1. See “List of compatible signals” on page 47 for available signals.
Appendix
52 - ENGLISH
S-VIDEO IN Single - line, Mini DIN 4p Y: 1.0 V [p-p], C: 0.286 V [p-p], 75 Ω

VIDEO IN Single - line, RCA pin jack1.0 V [p-p], 75Ω
Single - line, D - sub HD 15-pin (female)
Selectable for input and output by menu operation.
R.G.B. 0.7 V [p-p], 75 Ω
G.SYNC 1.0 V [p-p], 75 Ω
COMPUTER IN TTL high impedance, automatic
HD/SYNC positive/negative polarity
Terminals compatible
TTL high impedance, automatic
VD positive/negative polarity
compatible
Y, PB/CB, PR/CR Single - line, RCA pin jack x 3
COMPONENT IN Y: 1.0 V [p-p] (including sync), 75 Ω
PB/CB, (PR/CR) 0.7 V [p-p], 75 Ω
HDMI IN Triple - line, 19-pin HDMI connector
SERIAL D-sub 9-pin RS-232C compatible
Cabinet Moulded plastic (PC+ABS)
Width 460 mm (18 -3/32")
Dimensions Height 130 mm (5 -3/32")
Length 300 mm (11 -25/32")
Weight 7.2 kg (15.9 lbs.)
UL60950-1 C-UL
Certifications
FCC Class B ICES-003
Power supply 3 V DC (AA battery x 2)
Operating range Approx. 7 m (23') (when operated directly in front of signal receptor)
Weight 170 g (6 ozs.) (including batteries)
Remote control
Width 52 mm (2 -1/32")
Length 200 mm (7 -27/32")
Dimensions
28.5 mm (1 -3/32") (not including
Height
surface projection parts)
Cable cover ET-PCE2000
Ceiling bracket ET-PKE2000/ET-PKE1000S
Options
Projection screen ET-SRW90CC
ET-SC10CP (RCA pin jack x 3 - RCA pin jack x3)
Cables
ET-SC10DT (RCA pin jack x3 - D-Terminal)
Appendix
ENGLISH - 53
Dimensions
Unit: mm
300 (11-23/32)
15 (19/6)
(4 -9/16)
130
116
147 (5 -25/32)
60 (2 -5/16)
230 (9 -1/32) 17 (-21/32)

460 (18 -3/32)
Appendix
54 - ENGLISH
Trademark acknowledgements
VGA and XGA are trademarks of International Business Machines Corporation.
S-VGA is a registered trademark of the Video Electronics Standards Association.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
The font used in the on-screen displays is a Ricoh bitmap font, which is manufactured and sold by Ricoh
Company, Ltd.
All other trademarks are the property of the various trademark owners.
Appendix
These Operating Instructions are printed on recycled paper.
ENGLISH - 55
Index
A F
AC IN ......................................................................13 FOCUS
Accessories ..............................................................10 Control panel button ........................................... 12
ADVANCED MENU ...................................................33 LENS CONTROS menu ...................................... 39
Air exhaust port ........................................................12 FRAME RESPONSE ................................................ 40
Air filter ....................................................................12 FREEZE
Replacing ...........................................................43 Remote control button ........................................ 11
Air intake port ...........................................................13 Remote control function ...................................... 22
ALTITUDE ...............................................................41 Front leg adjusters ............................................. 13, 15
ASPECT ..................................................................36 FUNCTION BUTTON
Remote control button .........................................11 BUTTON1/2/3 .................................................... 39
Remote control function .......................................23 Main menu ........................................................ 39
AUTO SEARCH ........................................................40 Remote control buttons ....................................... 11
AUTO SETUP ..........................................................38
G
B GAMMA .................................................................. 33
BACK COLOR ..........................................................40
H
Batteries
HDMI IN
Accessory ..........................................................10
Connection ........................................................ 18
Compartment .....................................................11
Terminal ............................................................ 13
BLANK ....................................................................39
HDMI SIGNAL LEVEL .............................................. 40
BRIGHTNESS
H-POSITION ........................................................... 36
ADVANCED MENU .............................................33
PICTURE menu ..................................................31 I
C INPUT
Control panel button ........................................... 12
Ceiling mount bracket ................................................51
Remote control button ........................................ 11
CINEMA REALITY ....................................................34
Remote control function ...................................... 23
Cleaning ..................................................................43
INPUT GUIDE ......................................................... 40
CLOCK PHASE ........................................................36
INPUT SELECT
COLOR ....................................................................31
COLOR M.
INSTALLATION
Remote control button .........................................11
POSITION menu ................................................ 41
Remote control function .......................................26
Projection method .............................................. 15
COLOR MANAGEMENT ...........................................34
Remote control button .........................................11 K
Remote control function .......................................26 KEYSTONE ............................................................. 38
COLOR TEMPERATURE ..........................................32
COMPONENT IN
L
Connection .........................................................18 LAMP
Terminal ............................................................13 Indicator ............................................................ 12
COMPUTER IN Indicator status .................................................. 42
Connection .........................................................18 LAMP POWER ........................................................ 41
Terminal ............................................................13 LAMP RUNTIME ................................................ 41, 45
Connections .............................................................18 Lamp unit
CONTRAST Replacing .......................................................... 44
ADVANCED MENU .............................................33 LANGUAGE ............................................................ 29
PICTURE menu ..................................................31 LENS
Remote control button ........................................ 11
D Remote control function ...................................... 25
DEFAULT LENS CONTROL
Remote control button .........................................11 Main menu ........................................................ 39
Remote control function .......................................22 Remote control button ........................................ 11
DETAIL CLARITY .....................................................34 Lens cover .............................................................. 12
Dimensions ..............................................................54 Accessory ......................................................... 10
DOT CLOCK ............................................................36 Attachment hole ................................................. 13
DYNAMIC IRIS .........................................................32 Lens shift
E Lens shift dial • Horizontal ................................... 12
Lens shift dial • Vertical ....................................... 12
ENTER
LIGHT
Control panel button ............................................12
Remote control buttons ....................................... 11
Appendix

56 - ENGLISH
Index
M S
MAIN POWER ..........................................................12 Safety cable ............................................................ 51
MEM.LOAD Accessory ......................................................... 10
Remote control button .........................................11 Attachment point ................................................ 13
Remote control function .......................................23 Screen size ............................................................. 14
MEMORY EDIT ........................................................35 Calculation methods ........................................... 14
MEMORY LOAD .......................................................34 Security lock ............................................................ 13
Remote control button .........................................11 SERIAL
Remote control function .......................................23 Basic format ...................................................... 48
MEMORY SAVE .......................................................34 Cable specifications ........................................... 48
MENU Communication settings ...................................... 49
Control panel button ............................................12 Connection ........................................................ 48
Remote control button .........................................11 Control commands ............................................. 49
Remote control function .......................................30 Inquiry commands .............................................. 50
Menu Pin assignments ................................................ 48
Main menu .........................................................28 Terminal ............................................................ 13
Navigation ..........................................................30 SHARPNESS .......................................................... 31
Sub-menu ..........................................................28 SLEEP .................................................................... 41
MPEG NR ................................................................33 Remote control button ........................................ 11
N Specifications .......................................................... 52
Navigation buttons
SPLIT ADJUST ........................................................ 32
STARTUP LOGO ..................................................... 40
S-VIDEO IN
NR ..........................................................................33
Connection ........................................................ 18
O Terminal ............................................................ 13
OPTION menu ..........................................................40 T
OSD DESIGN ...........................................................40
Technical Information ............................................... 47
OSD POSITION ........................................................40
TEMP
OVER SCAN ............................................................38
Indicator ............................................................ 12
P Indicator status .................................................. 42
PIC.ADJUST Throw distance ........................................................ 14
Remote control button .........................................11 Throwing angle ........................................................ 15
Remote control function .......................................25 TINT ....................................................................... 31
PIC.MODE Top cover .......................................................... 13, 44
Remote control button .........................................11 Troubleshooting ....................................................... 46
PICTURE .................................................................31 TV-SYSTEM ............................................................ 34
Remote control button .........................................11 V
VIDEO IN
PICTURE MODE ......................................................31
Connection ........................................................ 18
Terminal ............................................................ 13
V-POSITION ............................................................ 36
POSITION ................................................................36
POWER W
Control panel button ............................................12 WAVEFORM
Indicator .............................................................12 Remote control button ........................................ 11
Indicator status ...................................................19 Remote control function ...................................... 24
Remote control button .........................................11 WAVEFORM MONITOR ........................................... 32
Power cord WSS ....................................................................... 38
Accessory ..........................................................10
X
Connecting .........................................................19
xvYCC .................................................................... 34
R Z
Remote control .........................................................11
ZOOM
Accessory ..........................................................10
Operating range ..................................................22
LENS CONTROL menu ...................................... 39
Operation ...........................................................22
ZOOM/FOCUS ........................................................ 39
Signal emitter .....................................................11
Signal receptor ...................................................12
Appendix
RETURN
ENGLISH - 57
NOTE:
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material - special handling may
apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
Projectors
Panasonic Projector Systems Company

Unit of Panasonic Corporation of North America
One Panasonic Way, Secaucpus, NJ 07094

(201) 392 - 6591
Technical Support:
(888) 411 - 1996
FAX: (201) 348 - 7523
E-Mail: projectorsupport@us.panasonic.com
Panasonic Canada Inc.

5770 Ambler Drive, Mississauga, Ontario L4W 2T3
(905) 624 - 5010
Panasonic Puerto Rico, Inc.

Ave. 65 de Infanteria, Km 9.5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985
(787) 750 - 4300
http://panasonic.net
Printed in Japan
© 2007 Matsushita Electric Industrial Co., Ltd. All Rights Reserved. S0807-1087B

PT-AE2000U: Operating Instructions

Uploaded by

Copyright:

Available Formats

PT-AE2000U: Operating Instructions

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PT-AE2000U: Operating Instructions

Uploaded by

Copyright:

Available Formats

Operating Instructions

Model No. PT-AE2000U

Dear Panasonic Customer:

Model number: PT-AE2000U

CAUTION: This equipment is equipped with a three-pin grounding-type power

Pursuant to at the directive 2004/108/EC, article 9(2)

Information on Disposal in other Countries outside the European Union

2. Connect with other devices Preparation

Do not look into the lens while the projector is being

Do not place your hands or other objects close to the

Replacement of the lamp is recommended to be

When replacing the lamp, allow it to cool for at least

Before replacing the lamp, be sure to disconnect the

Do not allow infants or pets to touch the remote

Cautions when transporting

Cautions when installing

Power cord (x1)

Capture the projected

Lens cover Remote control signal Air exhaust port

(Push to open/close the cover.)

RETURN FOCUS and ZOOM

Air intake port

Safety cable attachment point

Front leg adjusters

Projection size (16 : 9) Throw distance (L)

SW (m) = SD (m) x 0.872 SH (m) = SD (m) x 0.490

LW (m) = 1.189 x SD (m) - 0.04 LT (m) = 2.378 x SD (m) - 0.05

INSTALLATION: FRONT/CEILING INSTALLATION: REAR/CEILING

Front leg adjusters and throwing angle

Lens shift and positioning

Turn the dial clockwise: Turning the dial counterclockwise:

Shifting the lever down:

Shifting the lever up:

Q When the projector position is fixed

100% Shift range

Connecting to COMPONENT IN/VIDEO IN/S-VIDEO IN

DVD player Video player DVD player

Connecting to COMPUTER IN/HDMI IN

RGB signal cable

Indicator status Status

No illumination or flashing The MAIN POWER button is switched off.

Switching on the projector

Switching off the projector

Positioning the image

control may not operate correctly.

Turning on the button backlight

Resetting to the factory default settings

Switching the input signal

COMPUTER (RGB) signal from the

Loading a saved setting

Adjusting the signal condition with a waveform

COMPUTER (except 1080)

Adjust to 0% Monitor position Adjust to 0%

J Displaying the waveform J Adjustment example

waveform monitor. adjustment on the screen and press the

Adjusting the focus and zoom

Switching the picture mode

Adjusting the image

Switching off the projector automatically