Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 45 views

    Harmony Symphony - Setup of IIT13 Based On FPGA and Firmware Revisions

    Uploaded by

    Yhony Gamarra Vargas
    This document provides a technical description of how to set up an INIIT13 module depending on its FPGA revision, firmware revision, and switch settings. It notes that the FPGA will have a label with a 4 digit number and lists possible numbers. It states the firmware revision can be found using inspection utility but chips may not reflect current revision. A table shows the supported combinations of FPGA revision, firmware revision, and switch settings.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Harmony Symphony - Setup of IIT13 Based On FPGA and Firmware Revisions

    Uploaded by

    Yhony Gamarra Vargas
    45 views2 pages
    This document provides a technical description of how to set up an INIIT13 module depending on its FPGA revision, firmware revision, and switch settings. It notes that the FPGA will have a label with a 4 digit number and lists possible numbers. It states the firmware revision can be found using inspection utility but chips may not reflect current revision. A table shows the supported combinations of FPGA revision, firmware revision, and switch settings.

    Original Title

    Harmony_Symphony_-_Setup_of_IIT13_based_on_FPGA_and_firmware_revisions

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides a technical description of how to set up an INIIT13 module depending on its FPGA revision, firmware revision, and switch settings. It notes that the FPGA will have a label with a 4 digit number and lists possible numbers. It states the firmware revision can be found using inspection utility but chips may not reflect current revision. A table shows the supported combinations of FPGA revision, firmware revision, and switch settings.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    45 views2 pages

    Harmony Symphony - Setup of IIT13 Based On FPGA and Firmware Revisions

    Uploaded by

    Yhony Gamarra Vargas
    This document provides a technical description of how to set up an INIIT13 module depending on its FPGA revision, firmware revision, and switch settings. It notes that the FPGA will have a label with a 4 digit number and lists possible numbers. It states the firmware revision can be found using inspection utility but chips may not reflect current revision. A table shows the supported combinations of FPGA revision, firmware revision, and switch settings.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Technical Description

    Harmony/Symphony - Setup of IIT13 based on FPGA and firmware revisions

    Products Concerned: INIIT13

    Description: The setup of the INIIT13 module is dependent on the revision of FPGA and firmware
    installed on the INIIT13

    - The FPGA is in chip U26. It will have a small label on it with a 4 digit number. The
    numbers that could be on that label are:
    E19B, BF19, 9D49, or EC8E

    - The firmware can be read using the Composer Inspect utility.


    Firmware chips in position U24 and U25 also have a label indicating the revision,
    however, the firmware on the INIIT13 is flashable so there is no guarantee that the label
    on these chips reflects the current firmware revision. The Composer Inspect utility will
    give the actual revision running in the module.

    - The switch settings involved are the cache enables, SW4 , poles 6, 7, and 8

    The supported combinations are listed in Table 1.

    Table 1

    FPGA rev Firmware revision Switch settings


    E19B C_0 SW4, 6,7,8 = 0,0,0 or 1,1,1
    E19B C_1, C_2 SW4 6,7,8 = 1,1,1
    BF19, 9D49, EC8E C_1, C_2 SW4 6,7,8 = 1,1,1

    ABB Inc.

    Doc. Id. 3BUA001799R0001 Rev. A Date. 2011-Aug-24 1 (2)


    REVISION

    Rev. ind.: Page (P) Description Date


    Chapt. (C) Dept.

    ABB Inc.

    Doc. Id. 3BUA001799R0001 Rev. A Date. 2011-Aug-24 2 (2)

    You might also like