Design Calculation For 9 MM Fibrous Plaster Ceiling

Design Calculation for 9 mm Fibrous Plaster Ceiling with CB3212 Ceiling Frame
Design Calculation for 9 mm Fibrous Plaster Ceiling Frame
Design limitation
1) Ceiling batten dimension
a) 32.0 mm x 12 mm x 0.35 bmt ceiling batten
2) 9.0 mm thick Fibrous Plasterboard, weight considered = 7.00 kg/m2
3) Ceiling batten frame design to carry it self-weight = 2.0 kg/m2
4) Total Dead Load, DL = 9.00 kg/m2 = 0.09 kPa
5) No internal pressure considered in the design calculation
6) Maximum allowable services loading = 0.05 kPa
7) Strength Check , 1.4 G + 1.7 U(In accordance to AS 2785)
8) Deflection Limit: L/360 & shall not be greater than 12mm under services
loading 1.0 G +1.0 U
9) Ceiling Suspension 32 mm x 12 mm x 0.35 bmt @ 900 mm
10) Primary Section 32 mm x 12 mm x 0.35 bmt @ 900 mm
11) Secondary Section 32mm x 12 mm x 0.35bmt @ 406 mm
12) Ceiling Drop Considered = 2000 mm
1|Page
Design Calculation
for CB3212 - 9 mm Fibrous Plaster Ceiling.docx
Design for Primary Section (32 mm x 12 mm x 0.35 bmt @ 900 mm)
Structural Analysis & Deflection Check
R1 R2 R3
L L
Section Properties
Profile : TECHNO
U-Metal32
32mm
mm xx 12
12 mm
mmxx0.35
0.35bmt
bmtCeiling
CeilingBatten
batten
I xx : 3.25E-09 m4
Analysis Input
Total Length : 3.6 m
L: 0.9 m
Loading and Spacing Section Analysis
Spacing = 0.9 m R1 = R3 = 0.0483 kN
2
Pressure, U = 0.03 kN/m R2 = 0.16099 kN
U= 0.027 kN/m V 1 = V max = 0.08049 kN
Design Factor = 1.7 M1 = 0.01449 kNm
weight = 0.09 kN/m2 M2 = 0.00815 kNm
G= 0.081 kN/m d= 0.58926 mm
Design Factor = 1.2 < 2.5, L/1527.34 >L/360; Satisfatory
Total Factored Load = 0.1431 kN/m
Total Unfactored Load = 0.108 kN/m
2|Page
Primary Section - Strength Check

Results of Analysis by ColdSteel/4600, Version 2.2.04, 18 May 2015
==================================================================
24/7/2020 5:19:44 PM
Licence No. CS22.169
Check ID: Member 1
Section Class: Lipped Channel
Section Designation: CB32/12
Material Grade: G300
Governing Capacity/Action Strength Check (>= 1.0 is SAFE)
Minimum Capacity/Action Ratio (ØRu/S*) = 1.374 (SAFE) > 1.0 (Satisfactory)
Member capacity (lateral buckling) in bending about x-axis (Mbx)
(AS/NZS 4600:2005, Clause 3.3.3.2)
Units
Length: Metres
Force: KiloNewtons
Mass: Kilograms
Input Parameters
- Member and section capacity checks conducted.
- Design actions come first-order elastic structural analysis.
- Thin-walled theory is used for calculation of cross-section properties.
- Square corners are used for calculation of torsional section properties.
- Shear centre and warping constant are calculated on-the-fly.
- Princpial (x-y) axes are used.
- Phi-factors from AS/NZS 4600:2005 are used in design calculations.
- Mox calculated using Clause 3.3.3.2 for bending strength check.
- Moy calculated using Clause 3.3.3.2 for bending strength check.
- Axial compression force (N*) is assumed to pass though effective section centroid
- Noc calculated using the given effective lengths (Lex, Ley, Lez)
- The possibility of torsional or torsional-flexural buckling in compression is considered
- Distortional buckling strength in compression is considered if relevant (Clause 3.4.6)
- Distortional buckling stress in compression (if relevant) is calculated using simple analytical model
- Distortional buckling stress in bending about x-axis (if relevant) is calculated using simple analytical model
- Distortional buckling stress in bending about y-axis (if relevant) is calculated using simple analytical model
2E008 kPa = E, Elastic modulus
8E007 kPa = G, Shear modulus
3E005 kPa = fy, Yield stress (nominal)
3.4E005 kPa = fu, Ultimate tensile strength (nominal)
3E005 kPa = fy, Yield stress (design)
3.4E005 kPa = fu, Ultimate tensile strength (design)
7850 kg/m3 = rho, Mass density
3.6 m = Lx, Actual member length for bending aboutx-axis
3.6 m = Ly, Actual member length for bending abouty-axis
0.9 m = Lebx, Beam effective length for buckling about x-axis
0.9 m = Leby, Beam effective length for buckling about y-axis
0.6 m = Lebz, Beam effective length for buckling about z-axis
0.9 m = Lecx, Column effective length for buckling about x-axis
0.9 m = Lecy, Column effective length for buckling about y-axis
0.6 m = Lecz, Column effective length for buckling about z-axis
1 = kt, Tension factor
0 m = Brem, Equivalent removed width
Fastened = Bearing Support Condition
One-Flange End = Bearing Load Case
0.05 m = Lb, Bearing length
3|Page
1 = Cbx, coefficient for calculation of buckling moment Mox

1 = 1/CTFy, coefficient for calculation of buckling moment Moy
1 = Cmx, Moment modification factor (combined tension/compression & bending)
1 = Cmy, Moment modification factor (combined tension/compression & bending)
0 kN = N*, Design axial force (tension positive)
0.01449 kNm = Mx*, Design bending moment about x-axis
0 kNm = My*, Design bending moment about y-axis
0.08049 kN = Vx*, Design shear force in direction of x-axis
Capacity/Action Ratios for all Limit States
[ - ] = (ØRu/S*)(Nty) (Yielding in tension, Clause 3.2.1, Eq. 3.2.2(1))
[ - ] = (ØRu/S*)(Ntu) (Fracture in tension, Clause 3.2.1, Eq. 3.2.2(2))
3.54 = (ØRu/S*)(Msx) (Section capacity in bending about x-axis, Clause 3.3.2)
[ - ] = (ØRu/S*)(Msy) (Section capacity in bending about y-axis, Clause 3.3.2)
1.374 = (ØRu/S*)(Mblx) (Lateral buckling about x-axis, Clause 3.3.3.2)
[ - ] = (ØRu/S*)(Mbly) (Lateral buckling about y-axis, Clause 3.3.3.2)
3.1238 = (ØRu/S*)(Mbdx) (Distortional buckling about x-axis, Clause 3.3.3.3)
[ - ] = (ØRu/S*)(Mbdy) (Distortional buckling about y-axis, Clause 3.3.3.3)
16.681 = (ØRu/S*)(Vvx) (Shear in x-axis direction, Clause 3.3.4)
[ - ] = (ØRu/S*)(Vvy) (Shear in y-axis direction, Clause 3.3.4)
16.681 = (ØRu/S*)(Vvx+Msy) (Combined shear and bending, Clause 3.3.5)
3.54 = (ØRu/S*)(Vvy+Msx) (Combined shear and bending, Clause 3.3.5)
[ - ] = (ØRu/S*)(Rbx) (Bearing in x-axis direction, Clause 3.3.6)
[ - ] = (ØRu/S*)(Rby) (Bearing in y-axis direction, Clause 3.3.6)
[ - ] = (ØRu/S*)(Rbx+Msy) (Bearing and bending, Clause 3.3.7)
3.54 = (ØRu/S*)(Rby+Msx) (Bearing and bending, Clause 3.3.7)
[ - ] = (ØRu/S*)(Ns) (Section capacity in compression, Clause 3.4.1(a))
[ - ] = (ØRu/S*)(Ncft) (Flexural or flexural-torsional buckling capacity in compression, Clause 3.4.1)
[ - ] = (ØRu/S*)(Ncd) (Distortional buckling capacity in compression, Clause 3.4.6)
1.374 = (ØRu/S*)(Mx+My+Nc, Combined compression and bending, Clause 3.5.1(a))
1.374 = (ØRu/S*)(Mx+My+Nc, Combined compression and bending, Clause 3.5.1(b))
1.374 = (ØRu/S*)(Mx+My+Nc, Combined compression and bending, Clause 3.5.1, N*/phiNc <= 0.15)
1.374 = (ØRu/S*)(Mx+My+Nt, Combined tension and bending, Clause 3.5.2(a))
4.1405 = (ØRu/S*)(Mx+My+Nt, Combined tension and bending, Clause 3.5.2(b))
Design Capacities
5.651 kN = ØNty (Ø = 0.90)
5.4438 kN = ØNtu (Ø = 0.90)
0.051294 kNm = ØMsx+ (Ø = 0.95)
0.051294 kNm = ØMsx- (Ø = 0.95)
0.011736 kNm = ØMsy+ (Ø = 0.90)
0.011766 kNm = ØMsy- (Ø = 0.95)
0.019909 kNm = ØMbx+ (Ø = 0.90)
0.019909 kNm = ØMbx- (Ø = 0.90)
0.009581 kNm = ØMby+ (Ø = 0.90)
0.011766 kNm = ØMby- (Ø = 0.90)
0.059996 kNm = ØMsfx+ (Ø = 0.95)
0.059996 kNm = ØMsfx- (Ø = 0.95)
0.031213 kNm = ØMsfy+ (Ø = 0.90)
0.012388 kNm = ØMsfy- (Ø = 0.95)
1.3427 kN = ØVvx (Ø = 0.90)
1.1992 kN = ØVvy (Ø = 0.90)
[ - ] kN = ØRbx (Ø = 0.85)
0.45198 kN = ØRby (Ø = 0.85)
3.2566 kN = ØNs (Ø = 0.85)
0.71723 kN = ØNcft (Ø = 0.85)
3.0528 kN = ØNcd (Ø = 0.85)
0.045264 kNm = ØMbdx+ (Ø = 0.90)
0.045264 kNm = ØMbdx- (Ø = 0.90)
0.0094774 kNm = ØMbdy+ (Ø = 0.90)
[ - ] kNm = ØMbdy- (Ø = 0.90)
Cross-Sectional Dimensions
0.00035 m = Thickness (t)
0.032 m = Overall depth (D)
4|Page
0.012 m = Overall flange width (B)

0.0023 m = Stiffener length (L)
0.00035 m = Internal corner radius (R)
Properties of Full Section

0.0597987 m = Wf, Feed width
2.09295E-005 m2 = A (full section)
2.09295E-005 m2 = A (net section)
0.00324061 m = xc, x-ordinate of centroid (full section)
0 m = yc, y-ordinate of centroid (full section)
-0.00841984 m = xo, x-ordinate of shear centre (referred to principal axes)
0 m = yo, y-ordinate of shear centre (referred to principal axes)
3.250E-009 m4 = Ix (full section)
3.750E-010 m4 = Iy (full section)
0 m4 = Ixy (full section)
0 deg = Inclination of principal axes (full section)
0.0127846 m = rx (full section), radius of gyration
0.00434353 m = ry (full section), radius of gyration
-0.00341561 m = Extreme negative x-ordinate (full section)
0.00908439 m = Extreme positive x-ordinate (full section)
-0.01625 m = Extreme negative y-ordinate (full section)
0.01625 m = Extreme positive y-ordinate (full section)
2.10513E-007 m3 = Zx+, Full section modulus (yield at extreme positive y-ordinate)
2.10513E-007 m3 = Zx-, Full section modulus (yield at extreme negative y-ordinate)
4.34659E-008 m3 = Zy+, Full section modulus (yield at extreme positive x-ordinate)
1.15605E-007 m3 = Zy-, Full section modulus (yield at extreme negative x-ordinate)
8.54623E-013 m4 = J, torsion constant (full section)
0.0159696 m = ro1 (full section)
0 m = betax, monosymmetry parameter (referred to principal axes)
0.035496 m = betay, monosymmetry parameter (referred to principal axes)
8.02807E-014 m6 = Iw, warping constant (full section)
0.164297 kg/m = Mass per unit length
0.120297 m = Profile distance
0.732195 m2/kg = Profile surface area (Area/Mass)
Properties of Effective Section

1.2771E-005 m2 = Ae(fy) Effective area for uniform stress fy
2.0927E-005 m2 = Ae(fn) Effective area for uniform stress fn
3.1013E-009 m4 = Iex+, effective 2nd moment of area (x+ bending, extreme fibre at yield)
3.1013E-009 m4 = Iex-, effective 2nd moment of area (x- bending, extreme fibre at yield)
3.9486E-010 m4 = Iey+, effective 2nd moment of area (y+ bending, extreme fibre at yield)
3.4423E-010 m4 = Iey-, effective 2nd moment of area (y- bending, extreme fibre at yield)
1.7998E-007 m3 = Zex+, effective section modulus at yield (x+ bending)
1.7998E-007 m3 = Zex-, effective section modulus at yield (x- bending)
4.3466E-008 m3 = Zey+, effective section modulus at yield (y+ bending)
4.1285E-008 m3 = Zey-, effective section modulus at yield (y- bending)
Miscellaneous Parameters
3.9831E005 kPa = fox, Elastic buckling stress for buckling about principal x-axis
45976 kPa = foy, Elastic buckling stress for buckling about principal y-axis
95278 kPa = foz, Elastic buckling stress for torsional buckling about z-axis
45976 kPa = foc, Elastic buckling stress
40321 kPa = fn, Inelastic buckling stress
8.3364 kN = Nox, Elastic flexural buckling load about x-axis (used for moment amplification)
0.96225 kN = Noy, Elastic flexural buckling load about y-axis (used for moment amplification)
0.022122 kNm = Mox+, Elastic lateral buckling moment for positive bending about x-axis
0.022122 kNm = Mox-, Elastic lateral buckling moment for negative bending about x-axis
0.013694 kNm = Moy+, Elastic lateral buckling moment for positive bending about y-axis
0.3096 kNm = Moy-, Elastic lateral buckling moment for negative bending about y-axis
-7.8297E-005 m = x-ordinate of C(full)->C(effective) (fy)
0 m = y-ordinate of C(full)->C(effective) (fy)
3.8151E-007 m = x-ordinate of C(full)->C(effective) (fn)
0 m = y-ordinate of C(full)->C(effective) (fn)
[ - ] m4 = Ie_Mx*, Effective second moment of area for design Mx*
5|Page
[ - ] m3 = Ze_Mx*, Effective section modulus for design Mx*

[ - ] m4 = Ie_My*, Effective second moment of area for design My*
[ - ] m3 = Ze_My*, Effective section modulus for design My*
1.7523E005 kPa = fodc, Distortional buckling stress in pure compression
3.1799E005 kPa = fodx+, Distortional buckling stress in bending
3.1799E005 kPa = fodx-, Distortional buckling stress in bending
3.8974E005 kPa = fody+, Distortional buckling stress in bending
[ - ] kPa = fody-, Distortional buckling stress in bending
Design for Secondary Section (32 mm x 12 mm x 0.35 bmt @ 406 mm)
Structural Analysis & Deflection Check
R1 R2 R3
L L
Section Properties
Profile : TECHNO 32 mm
U-Metal x 12xmm
32 mm 12 xmm
0.35xbmt
0.35Ceiling batten Batten
bmt Ceiling
I yy : 3.75E-10 m4
Analysis Input
Total Length : 3.6 m
L: 0.9 m
Loading and Spacing Section Analysis
Spacing = 0.406 m R1 = R3 = 0.02179 kN
2
Pressure, U = 0.03 kN/m R2 = 0.07262 kN
U = 0.01218 kN/m V 1 = V max = 0.03631 kN
Design Factor = 1.7 M1 = 0.00654 kNm
2
weight = 0.09 kN/m M2 = 0.00368 kNm
G = 0.03654 kN/m d= 2.3038 mm
Design Factor = 1.2 < 2.5, L/390.66 >L/360; Satisfatory
Total Factored Load = 0.06455 kN/m
Total Unfactored Load = 0.04872 kN/m
6|Page
Secondary Section - Strength Check

==================================================================
24/7/2020 5:27:33 PM
Check ID: Member 1
Member capacity (distortional buckling) in bending about y-axis (Mby); (AS/NZS 4600:2005, Clause 3.3.3.3)
Units
Length: Metres
Force: KiloNewtons
Mass: Kilograms
Input Parameters
0.9 m = Lebx, Beam effective length for buckling about x-axis
0.9 m = Leby, Beam effective length for buckling about y-axis
0.3 m = Lebz, Beam effective length for buckling about z-axis
0.9 m = Lecx, Column effective length for buckling about x-axis
0.9 m = Lecy, Column effective length for buckling about y-axis
0.3 m = Lecz, Column effective length for buckling about z-axis
7|Page

0 kN = N*, Design axial force (tension positive)
0 kNm = Mx*, Design bending moment about x-axis
0.00654 kNm = My*, Design bending moment about y-axis
0 kN = Vx*, Design shear force in direction of x-axis
0.03631 kN = Vy*, Design shear force in direction of y-axis
0 kN = Rx*, Design bearing force in direction of x-axis
0 kN = Ry*, Design bearing force in direction of y-axis

[ - ] = (ØRu/S*)(Nty) (Yielding in tension, Clause 3.2.1, Eq. 3.2.2(1))
[ - ] = (ØRu/S*)(Ntu) (Fracture in tension, Clause 3.2.1, Eq. 3.2.2(2))
[ - ] = (ØRu/S*)(Msx) (Section capacity in bending about x-axis, Clause 3.3.2)
1.7945 = (ØRu/S*)(Msy) (Section capacity in bending about y-axis, Clause 3.3.2)
[ - ] = (ØRu/S*)(Mblx) (Lateral buckling about x-axis, Clause 3.3.3.2)
1.7945 = (ØRu/S*)(Mbly) (Lateral buckling about y-axis, Clause 3.3.3.2)
[ - ] = (ØRu/S*)(Mbdx) (Distortional buckling about x-axis, Clause 3.3.3.3)
1.4491 = (ØRu/S*)(Mbdy) (Distortional buckling about y-axis, Clause 3.3.3.3)
[ - ] = (ØRu/S*)(Vvx) (Shear in x-axis direction, Clause 3.3.4)
33.028 = (ØRu/S*)(Vvy) (Shear in y-axis direction, Clause 3.3.4)
1.7945 = (ØRu/S*)(Vvx+Msy) (Combined shear and bending, Clause 3.3.5)
33.028 = (ØRu/S*)(Vvy+Msx) (Combined shear and bending, Clause 3.3.5)
[ - ] = (ØRu/S*)(Rby+Msx) (Bearing and bending, Clause 3.3.7)
1.4491 = (ØRu/S*)(Mx+My+Nc, Combined compression and bending, Clause 3.5.1(a))
1.4491 = (ØRu/S*)(Mx+My+Nc, Combined compression and bending, Clause 3.5.1(b))
1.4491 = (ØRu/S*)(Mx+My+Nc, Combined compression and bending, Clause 3.5.1, N*/phiNc <= 0.15)
1.4491 = (ØRu/S*)(Mx+My+Nt, Combined tension and bending, Clause 3.5.2(a))
Design Capacities
5.651 kN = ØNty (Ø = 0.90)
5.4438 kN = ØNtu (Ø = 0.90)
0.051294 kNm = ØMsx+ (Ø = 0.95)
0.051294 kNm = ØMsx- (Ø = 0.95)
0.011736 kNm = ØMsy+ (Ø = 0.90)
0.011766 kNm = ØMsy- (Ø = 0.95)
0.034996 kNm = ØMbx+ (Ø = 0.90)
0.034996 kNm = ØMbx- (Ø = 0.90)
0.011736 kNm = ØMby+ (Ø = 0.90)
0.011766 kNm = ØMby- (Ø = 0.90)
0.059996 kNm = ØMsfx+ (Ø = 0.95)
0.059996 kNm = ØMsfx- (Ø = 0.95)
0.031213 kNm = ØMsfy+ (Ø = 0.90)
0.012388 kNm = ØMsfy- (Ø = 0.95)
1.3427 kN = ØVvx (Ø = 0.90)
1.1992 kN = ØVvy (Ø = 0.90)
[ - ] kN = ØRbx (Ø = 0.85)
0.45198 kN = ØRby (Ø = 0.85)
3.2566 kN = ØNs (Ø = 0.85)
0.71723 kN = ØNcft (Ø = 0.85)
3.0528 kN = ØNcd (Ø = 0.85)
0.045264 kNm = ØMbdx+ (Ø = 0.90)
0.045264 kNm = ØMbdx- (Ø = 0.90)
0.0094774 kNm = ØMbdy+ (Ø = 0.90)
[ - ] kNm = ØMbdy- (Ø = 0.90)
8|Page


2.09295E-005 m2 = A (net section)

3.9831E005 kPa = fox, Elastic buckling stress for buckling about principal x-axis
45976 kPa = foy, Elastic buckling stress for buckling about principal y-axis
3.4268E005 kPa = foz, Elastic buckling stress for torsional buckling about z-axis
45976 kPa = foc, Elastic buckling stress
-7.8297E-005 m = x-ordinate of C(full)->C(effective) (fy)
3.8151E-007 m = x-ordinate of C(full)->C(effective) (fn)
9|Page

Suspension - Strength Check

==================================================================
24/7/2020 5:45:04 PM
Check ID: Member 1

---------------------------------------------------------
Fracture in tension (Ntu)
(AS/NZS 4600:2005, Clause 3.2.1, Eq. 3.2.2(2)
Units
-----
Length: Metres
Force: KiloNewtons
Mass: Kilograms
Input Parameters
----------------
10 | P a g e

2 m = Lebx, Beam effective length for buckling about x-axis
2 m = Leby, Beam effective length for buckling about y-axis
2 m = Lebz, Beam effective length for buckling about z-axis
2 m = Lecx, Column effective length for buckling about x-axis
2 m = Lecy, Column effective length for buckling about y-axis
2 m = Lecz, Column effective length for buckling about z-axis
0.16 kN = N*, Design axial force (tension positive)
0 kNm = Mx*, Design bending moment about x-axis
0 kNm = My*, Design bending moment about y-axis
0 kN = Vx*, Design shear force in direction of x-axis
0 kN = Vy*, Design shear force in direction of y-axis
0 kN = Rx*, Design bearing force in direction of x-axis
0 kN = Ry*, Design bearing force in direction of y-axis

-------------------------------------
34.433 = (ØRu/S*)(Nty) (Yielding in tension, Clause 3.2.1, Eq. 3.2.2(1))
33.17 = (ØRu/S*)(Ntu) (Fracture in tension, Clause 3.2.1, Eq. 3.2.2(2))
[ - ] = (ØRu/S*)(Msx) (Section capacity in bending about x-axis, Clause 3.3.2)
[ - ] = (ØRu/S*)(Msy) (Section capacity in bending about y-axis, Clause 3.3.2)
[ - ] = (ØRu/S*)(Mblx) (Lateral buckling about x-axis, Clause 3.3.3.2)
[ - ] = (ØRu/S*)(Mbly) (Lateral buckling about y-axis, Clause 3.3.3.2)
[ - ] = (ØRu/S*)(Mbdx) (Distortional buckling about x-axis, Clause 3.3.3.3)
[ - ] = (ØRu/S*)(Mbdy) (Distortional buckling about y-axis, Clause 3.3.3.3)
[ - ] = (ØRu/S*)(Vvx) (Shear in x-axis direction, Clause 3.3.4)
[ - ] = (ØRu/S*)(Vvy) (Shear in y-axis direction, Clause 3.3.4)
[ - ] = (ØRu/S*)(Vvx+Msy) (Combined shear and bending, Clause 3.3.5)
[ - ] = (ØRu/S*)(Vvy+Msx) (Combined shear and bending, Clause 3.3.5)
[ - ] = (ØRu/S*)(Rby+Msx) (Bearing and bending, Clause 3.3.7)
[ - ] = (ØRu/S*)(Mx+My+Nc, Combined compression and bending, Clause 3.5.1(a))
11 | P a g e
[ - ] = (ØRu/S*)(Mx+My+Nc, Combined compression and bending, Clause 3.5.1(b))

[ - ] = (ØRu/S*)(Mx+My+Nc, Combined compression and bending, Clause 3.5.1, N*/phiNc <= 0.15)
[ - ] = (ØRu/S*)(Mx+My+Nt, Combined tension and bending, Clause 3.5.2(a))
Design Capacities
-----------------
5.5092 kN = ØNty (Ø = 0.90)
5.3072 kN = ØNtu (Ø = 0.90)
0.049974 kNm = ØMsx+ (Ø = 0.95)
0.049974 kNm = ØMsx- (Ø = 0.95)
0.010963 kNm = ØMsy+ (Ø = 0.90)
0.011026 kNm = ØMsy- (Ø = 0.95)
0.0037903 kNm = ØMbx+ (Ø = 0.90)
0.0037903 kNm = ØMbx- (Ø = 0.90)
0.0024968 kNm = ØMby+ (Ø = 0.90)
0.011026 kNm = ØMby- (Ø = 0.90)
0.057219 kNm = ØMsfx+ (Ø = 0.95)
0.057219 kNm = ØMsfx- (Ø = 0.95)
0.029363 kNm = ØMsfy+ (Ø = 0.90)
0.011572 kNm = ØMsfy- (Ø = 0.95)
1.2822 kN = ØVvx (Ø = 0.90)
1.2188 kN = ØVvy (Ø = 0.90)
[ - ] kN = ØRbx (Ø = 0.85)
0.45282 kN = ØRby (Ø = 0.85)
3.2559 kN = ØNs (Ø = 0.85)
0.13051 kN = ØNcft (Ø = 0.85)
3.0786 kN = ØNcd (Ø = 0.85)
0.04421 kNm = ØMbdx+ (Ø = 0.90)
0.04421 kNm = ØMbdx- (Ø = 0.90)
0.0089927 kNm = ØMbdy+ (Ø = 0.90)
[ - ] kNm = ØMbdy- (Ø = 0.90)
--------------------------

--------------------------
2.04045E-005 m2 = A (net section)
12 | P a g e

0 m = betax, monosymmetry parameter (referred to principal axes)

-------------------------------
------------------------
77689 kPa = fox, Elastic buckling stress for buckling about principal x-axis
8580.4 kPa = foy, Elastic buckling stress for buckling about principal y-axis
20560 kPa = foz, Elastic buckling stress for torsional buckling about z-axis
8580.4 kPa = foc, Elastic buckling stress
5.7697E-005 m = x-ordinate of C(full)->C(effective) (fy)
0 m = x-ordinate of C(full)->C(effective) (fn)
-End-
13 | P a g e

Design Calculation For 9 MM Fibrous Plaster Ceiling

Uploaded by

Copyright:

Available Formats

Design Calculation For 9 MM Fibrous Plaster Ceiling

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Design Calculation For 9 MM Fibrous Plaster Ceiling

Uploaded by

Copyright:

Available Formats

Design Calculation for 9 mm Fibrous Plaster Ceiling with CB3212 Ceiling Frame

Design Calculation for 9 mm Fibrous Plaster Ceiling Frame

Design for Primary Section (32 mm x 12 mm x 0.35 bmt @ 900 mm)

Structural Analysis & Deflection Check

Primary Section - Strength Check

1 = Cbx, coefficient for calculation of buckling moment Mox

0.012 m = Overall flange width (B)

Properties of Full Section

Properties of Effective Section

[ - ] m3 = Ze_Mx*, Effective section modulus for design Mx*

Structural Analysis & Deflection Check

Secondary Section - Strength Check

1 = 1/CTFy, coefficient for calculation of buckling moment Moy

Capacity/Action Ratios for all Limit States

0.032 m = Overall depth (D)

Properties of Full Section

Properties of Effective Section

[ - ] m3 = Ze_Mx*, Effective section modulus for design Mx*

Results of Analysis by ColdSteel/4600, Version 2.2.04, 18 May 2015

Governing Capacity/Action Strength Check (>= 1.0 is SAFE)

- Phi-factors from AS/NZS 4600:2005 are used in design calculations.

Capacity/Action Ratios for all Limit States

[ - ] = (ØRu/S*)(Mx+My+Nc, Combined compression and bending, Clause 3.5.1(b))

Properties of Full Section

8.33185E-013 m4 = J, torsion constant (full section)

Properties of Effective Section

You might also like

[ - ] m3 = Ze_Mx, Effective section modulus for design Mx

[ - ] m3 = Ze_Mx, Effective section modulus for design Mx