Raid

Configuring a RAID Set (B550 Series)
RAID Levels......................................................................................................................2
1-1 Configuring SATA Controllers.....................................................................................2

A. Installing SATA hard drive(s) in your computer........................................................ 2
B. Configuring SATA controller mode in BIOS Setup................................................... 3
C. UEFI RAID Configuration........................................................................................ 3
1-2 Installing the RAID Driver and Operating System......................................................7

A. Installing Windows .................................................................................................. 7
B. Rebuilding an Array................................................................................................. 8
-1-
RAID Levels
RAID 0 RAID 1 RAID 10
Minimum Number of
≥2 2 4
Hard Drives
Array Capacity Number of hard drives * Size of the smallest drive (Number of hard drives/2) *
Size of the smallest drive Size of the smallest drive
Fault Tolerance No Yes Yes
To configure SATA hard drive(s), follow the steps below:

A. Install hard drive(s) in your computer.
B. Configure SATA controller mode in BIOS Setup.
C. Configure a RAID array in RAID BIOS (Note 1)
D. Install the RAID driver and operating system
Before you begin

•• At least two SATA hard drives or SSDs (Note 2) (to ensure optimal performance, it is recommended that you
use two hard drives with identical model and capacity). (Note 3)
•• A Windows setup disc.
•• Motherboard driver disc.
•• A USB thumb drive.
1-1 Configuring SATA Controllers

A. Installing SATA hard drive(s) in your computer
Install the hard drives/SSDs in the SATA/M.2 connectors on the motherboard. Then connect the power
connectors from your power supply to the hard drives.
(Note 1) Skip this step if you do not want to create RAID array on the SATA controller.
(Note 2) An M.2 PCIe SSD cannot be used to set up a RAID set either with an M.2 SATA SSD or a SATA hard drive.
(Note 3) Refer to "Internal Connectors," for the installation notices for the M.2, and SATA connectors.
-2-
B. Configuring SATA controller mode in BIOS Setup
Make sure to configure the SATA controller mode correctly in system BIOS Setup.
Step:
Turn on your computer and press <Delete> to enter BIOS Setup during the POST (Power-On Self-Test). Under
Settings\IO Ports, set SATA Configuration\SATA Mode to RAID (Figure 1). Then save the settings and
restart your computer. (If you want to use NVMe PCIe SSDs to configure RAID, make sure to set NVMe RAID
mode to Enabled.)
Figure 1
C. UEFI RAID Configuration

Step 1:
In BIOS Setup, go to Boot and set CSM Support to Disabled (Figure 2). Save the changes and exit BIOS Setup.
Figure 2
The BIOS Setup menus described in this section may differ from the exact settings for your motherboard.
The actual BIOS Setup menu options you will see shall depend on the motherboard you have and
the BIOS version.
-3-
Step 2:
After the system reboot, enter BIOS Setup again. Then enter the Settings\IO Ports\RAIDXpert2 Configuration
Utility sub-menu (Figure 3).
Figure 3
Step 3:
On the RAIDXpert2 Configuration Utility screen, press <Enter> on Array Management to enter the Create
Array screen. Then, select a RAID level (Figure 4). RAID levels supported include RAID 0, RAID 1, and RAID
10 (the selections available depend on the number of the hard drives being installed). Next, press <Enter> on
Select Physical Disks to enter the Select Physical Disks screen.
Figure 4
-4-
Step 4:
On the Select Physical Disks screen, select the hard drives to be included in the RAID array and set them
to Enabled. Next, use the down arrow key to move to Apply Changes and press <Enter> (Figure 5).Then
return to the previous screen and set the Select CacheTagSize, Read Cache Policy and Write Cache Policy.
Figure 5
Step 5:
Move to Create Array and press <Enter> to begin. (Figure 6)
Figure 6
-5-
After completing, you'll be brought back to the Array Management screen. Under Manage Array Properties
you can see the new RAID volume and information on RAID level, array name, array capacity, etc. (Figure 7)
Figure 7
Delete RAID Volume

To delete a RAID array, select the array to be deleted on the RAIDXpert2 Configuration Utility\Array
Management\Delete Array screen. Press <Enter> on Delete Array to enter the Delete screen. Then set
Confirm to Enabled and press <Enter> on Yes (Figure 8).
Figure 8
-6-
1-2 Installing the RAID Driver and Operating System
With the correct BIOS settings, you are ready to install the operating system.
A. Installing Windows
As some operating systems already include RAID driver, you do not need to install separate RAID driver during
the Windows installation process. After the operating system is installed, we recommend that you install all
required drivers from the motherboard driver disc using "Xpress Install" to ensure system performance and
compatibility. If the operating system to be installed requires that you provide additional RAID driver during the
OS installation process, please refer to the steps below:
Step 1:
Copy the Hw10 folder under the \BootDrv folder in the driver disc to your USB thumb drive.
Step 2:
Boot from the Windows setup disc and perform standard OS installation steps. When the screen requesting you
to load the driver appears, select Browse.
Step 3:
Insert the USB thumb drive and then browse to the location of the driver. The location of the driver is as follows:
Windows 64-bit: \Hw10\RAID\x64
Step 4:
When a screen as shown in Figure 1 appears, select AMD-RAID Bottom Device first and click Next to load the
driver. Then select AMD-RAID Controller and click Next to load the driver. Finally, continue the OS installation.
Figure 1
-7-
B. Rebuilding an Array
Rebuilding is the process of restoring data to a hard drive from other drives in the array. Rebuilding applies
only to fault-tolerant arrays such as RAID 1 and RAID 10 arrays. To replace the old drive, make sure to use a
new drive of equal or greater capacity. The procedures below assume a new drive is added to replace a failed
drive to rebuild a RAID 1 array.
While in the operating system, make sure the Chipset and RAID drivers have been installed from the motherboard
driver disc. Then double-click the RAIDXpert2 icon on the desktop to launch the RAID utility.
Step 1: Step 2:
Enter the login ID and password (default: "admin"), In the Disk Devices section, left-click your mouse
and then click Submit to launch AMD RAIDXpert2. twice on the newly-added hard drive.
Step 3: Step 4:
On the next screen, select Assign as Global Spare During the rebuild process, you can select the array
and click Confirm. that is being built (displayed in red) in the Active
Volumes section to check the current progress.
Step 5:
Then rebuild is complete when the Task State
column shows "COMPLETED."
-8-

Raid

Uploaded by

Copyright:

Available Formats

Raid

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Raid

Uploaded by

Copyright:

Available Formats

Configuring a RAID Set (B550 Series)

1-1 Configuring SATA Controllers.....................................................................................2

1-2 Installing the RAID Driver and Operating System......................................................7

To configure SATA hard drive(s), follow the steps below:

Before you begin

1-1 Configuring SATA Controllers

C. UEFI RAID Configuration

Delete RAID Volume

You might also like