CHANDELIER

TING & FANS

RS
EC
LA
IR A EU
G E S & VE N T I L A T
Questions or Concerns Contact Canarm At:
1-800-265-1833 (English) or 1-800-567-2513 (French) Monday Through Friday 8:00am - 5:00pm E.S.T.
“INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS” TOOLS AND MATERIALS REQUIRED:
“READ ALL INSTRUCTIONS”

!
Wiring supplies
“IMPORTANT SAFETY Phillips Wire Cutters
as required by
the Canadian
INSTRUCTIONS” Screwdriver Electrical Code
and/or the
“SAVE THESE INSTRUCTIONS” Pliers Wrench
Quebec
Electrical code

SAFETY PRECAUTIONS:
1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.
2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
3. CONNECT THE GROUND WIRE (BARE COPPER OR GREEN) FROM YOUR FIXTURE TO THE GROUND
WIRE (BARE COPPER OR GREEN) OR GROUND SCREW IN THE ELECTRICAL OUTLET BOX.
4. CLEAN GLASS WITH WATER ONLY.
NOTE: Product May Not Look Exactly As Shown In Figures.
INSTALLATION:
STYLE #1A Bulb
Outlet Box
1. Attach the mounting bracket to the Shade 6. Note: Refer to the style of
outlet box using electrical box screws assembly that matches the style of
Mounting (not included) . Attach the nipple to the
your fixture.
Bracket mounting bracket and adjust until it will If your fixture has shades,
clear the canopy when assembled (Place
the canopy over the nipple and tighten
Nipple the upper connector onto the nipple Tube
until snug. The upper connector should STYLE #1A - Place shade on tube,
hold the canopy snug to the ceiling). STYLE #1B then install bulb.
Hex Nut Lock the nipple in the correct position Finial
Outlet Box Screws using the hex nut. STYLE #1B - Install bulb, shade
Shade
(not included)
Power
2. To attach chain loop to light fixture,
then finial.
use a screwdriver and wrench to open
Cord and close chain loop. Ensure to close Bulb
the opening. Weave the power cord and STYLE #2 - Remove spinner nut
ground wire through the links in the Tube from socket. Position glass on lamp
Chain chain. and secure with spinner nut.
STYLE #2 Note: Glass may face up or down.
Lower 3. Loosen the nut on the upper Spinner
Nut
Connector connector and slide it down the chain Note: If your fixture has
towards the lower connector. Slide the candle-style lights, slide the tubes
canopy down the chain towards the over the uplight sockets
lower connector. Feed the wire through
Nipple nut, canopy, the upper connector and Glass
onto the nipple. Tighten the upper Fixture STYLE #3 - Install proper bulb type
connector onto the nipple. Spread the
Socket and wattage before assembling
other end of the chain open and fasten the glass. Remove ball screw from
Canopy Upper to the upper connector. Ensure to close the curved stem. Position glass on
Connector the opening. STYLE #3 lamp with the curved stem being
inserted through the hole in the
4. Connect the ground wires (bare Glass
Hole
glass. Hand tighten the ball screw
copper or green) from your fixture to the to secure the glass in place.
Nut ground wire (bare copper or green) or For Stem
ground screw in the
electrical outlet box. Connect the black Ball Screw
wire (or wire marked “SPT-1”) from the
fixture to the black wire in the electrical
House supply
Ground wire box and connect the white wire from the 7. If not already done, install
Black fixture to the white wire in the electrical proper bulb type and wattage.
box. Fixture Note: If your product does not
5.
Once connections of wires are
have a bottom light, your fixture is
complete.
Fixture completed, carefully tuck wires and wire
Ground nuts into the outlet box making sure no
wire bare wire (on the black and white) is
visible at the wire nuts. Slide canopy Stem
into position and tighten in place by nut
White into position.
Fixture
8. Attach the stem to the fixture.
Note: If required, hook the support arms
onto fixture and then into the glass (or
hoop).
Note: If required assemble centre body
of fixture. Glass 9.
Position the glass over the
Note: If your product does not have any
Fibre stem. Secure the glass in place
uplights, please proceed to Step#8. Washer Hex Nut using the fibre washer, hex nut,
Note: If required, spread the arms of the decorative cap and finial.
fixture out evenly. Decorative Finial
Canopy Nut
Cap
Imported By: CANARM LTD., 2157 Parkedale Ave., Brockville, Ontario, K6V 5V6, Tel: (613) 342-5424, Fax: (800) 263-4598