SMNG 480
SMNG 480
SMNG 480
NG 4DR8RD
MODEL:SMNG480
Welcome
18:00 28/04/14
********************************************************************
SMART-I ELECTRONICS SYSTEMS PVT. LTD.(An ISO 9001:2008 certified company)
Corporate Office: A-308, Puranik Capital, Ghodbander Road, Opp hypercity, Kasar Vadavali, Thane (W) 400607
********************************************************************
R&D, Training & Customer Support Center:
First Floor, Arihant Plaza Phase II, Village-Ovala, Ghodbander Road, Thane (W) 400607
Tel: + 91-22-6566 6555
Web site: www.smartisystems.com
PRESENCE : MUMBAI - DELHI - BANGALORE – KOLKATA - CHENNAI - AHMEDABAD – PUNE - HYDERABAD
1
Contents
PRODUCT SELECTION ............................................................................................................... 4
INTRODUCTION .......................................................................................................................... 5
DEVICE CONFIGURATION ........................................................................................................ 6
SPECIFICATION ........................................................................................................................... 7
Hardware specification: ............................................................................................................... 7
Access control features: ............................................................................................................... 7
KEYPAD DETAILS ....................................................................................................................... 8
NG 4DR8RD CONNECTION DETAILS: ................................................................................... 13
RECOMMENDED CABLE SPECIFICATION ........................................................................... 15
CONNECTING TO HOST COMPUTER USING ....................................................................... 15
2
WARNING & CAUTION
Ø Please handle the equipment with care. Physical Damage to the system is not covered under
warranty.
Ø Do not power on the system without reading this manual. Ensure proper power supply with
Earthing.
Ø Note down the serial number and model no. of the device for future reference and quote in all
support and service requests.
Ø To connect or interface the Card reader to the Smart XS NG unit please refer to the Hardware
Installation Guide or Manual and carefully follow the instructions. A trained technician must make
the connections.
Any negligence on your part may damage the Card reader interface on the Smart XS NG terminal.
Ø Mounting the unit in strong sunlight may affect user visibility of the LCD. Ensure that the LCD and
LED’s are clearly visible in all lighting conditions.
Ø The fingerprint sensor glass may periodically require cleaning - use suitable glass cleaner.
Ø Do not uses this unit near water.
Ø Do not opens system or places it near other heavy electrical equipment. The system is sensitive
to Electro Static Discharge (ESD)
Ø Never insert objects of any kind into the unit or through the cabinet slots as they may touch
voltage points and/or short circuit parts possibly resulting in fire or electric shock. Never spill
liquid of any kind on the unit.
Ø when connecting up the Controller Access Controller ensure that the mains power supply is
safely isolated. Power up the controller only when installation is complete.
Ø Operating conditions: 0 to 55 deg Celsius and 50 deg Celsius at 90% RH.
When connecting card or Biometric readers to any emergency entry, exit door, barrier or elevator
must provide an alternative exit in accordance with all fire and life safety codes pertinent to the
installation. These fire and safety codes vary from city to city and you must get approval from local
fire officials whenever using an electronic product to control a door or other barrier.
Important Instructions
Care should be taken identifying the wires. Improper wiring may render permanent damage
to the device or personal injury.
Refer the color code on the Reader to connect the external weigand reader on the controller.
Check the earthing at the site before installing the controllers. Normally the earthing should
be between 1V to 2V only. Earthing on the higher side may damage the controller or its
various other components.
Before Installation delete all data ( Factory reset ) using keypad menu * 90
Disclaimer
Changing of default user password is mandatory to avoid tampering of the device.
In case of user password not changed; smart I will not be responsible for any tampering on
the device.
3
1. Before you start with smart XS NG
1.1. Included items
Smart XS NG unit
Battery Backup Power supply 12 V 5A
This Installation Guide
In case you do not have the required power supply included in the package and intends to buy your
own power supply use these specifications. Below given specifications should be strictly adhered
to.
4
PRODUCT SELECTION
Particulars Specifications
Model no. SMNG480 Series
INTRODUCTION
The new NG SMART 4door 8reader blends loads of innovative features to streamline installation
and administration for large business enterprises for multiple doors access control deployment. NG
4dr8rd brings the high speed, accuracy, flexibility and user friendly interactivity.
Welcome
18:00 28/04/14
5
DEVICE CONFIGURATION
Door 2 Door 3
Egress
Egress
Lock for
Lock for
door 3
door 2
Welcome
18:00 28/04/14 Lock for
Lock for door 4
door 1
For TCP communication
Door 1 Door 4
Reader 8 Reader 7
Reader 2
Reader 1
Egress Egress
6
SPECIFICATION
Hardware specification:
Particulars Description
CPU 32 Bit RISC Arm
Memory Flash 4MB
Events/Transactions 60,000
No. of Users 30,000
Operation Modes Card Only, (On Weigand Card Only).
Card Reader Options (extra
Mifare, HID (I Class), HID Prox, EM cards.
Module)
Communications Port TCP/IP, RS485
Baud Rate 9600bps (Default)
Controller ID Max 9999
LCD 16x2
Keypad Dome keypad
Language English
Power Supply 12 V DC/ 5A (Min)
Enclosure
Color / Weight
Dimension (L X H X D) in
mm
Mounting Wall Mounting
Particulars Description
Facility Code Available
Time Zone / Access 63 + 1 (Free Time Zone)/Unlimited
Levels
Time Zone Slots 4 slots per Day
Anti-Pass back Hard, Soft, Escort (Reader Wise)
Holiday Settings 42
7
KEYPAD DETAILS
Sr. No. Function How to go? Note Observation
(IDEAL)
1. Normal mode Key – *0 In this mode card is shown
Key – *2 To log out from Admin mode
Enter User ID – 11111 press
2. Admin Mode Key – # Key – *2
Enter Password – 12345 Key – #
Key – # (Auto logoff after 60sec)
Key – *3 After showing card to reader 1,
3. Add User Show card card no will come automatically
Key – # on LCD then press #
Key – *4 After showing card to reader 1,
4. Delete User Show card press #. Then that user gets
Key – # deleted.
Key – *5 If user is added then it will
5. Search User Show card show card no with password.
Key – #
Key – *6
6. Set Time & Date Enter Time/Date Enter correct Date & Time.
Key – #
Key – *8
7. Help Menu Press – 1 for INC We can directly go in to any
Press – 3 for DEC menu by pressing “#” key.
Press – # to enter
00 Delete all data Refer
01 Delete Transaction Annexure:1
02 Delete All Users
Key – *90 03 Set All Default
8. Press – 1 for INC 04 Delete Sys. Info
Initialize system Press – 3 for DEC 05 Delete Time Zone
Key – # to enter 06 Delete Holiday
07 Delete Facility Code
08 Delete Door info
09 Delete Admin IDs
10 Reset System
11 Delete Cards Only
Key – *91 By default it is set to 1.
9. Controller Slave Enter Controller Slave We can assign controller ID
ID ID from 1 to 32.
Key – #
Key – *92 We can add max 16 admin users
Press – 1 for Add/Ch (0 – 65535 nos) including
Add / Change or Press – 3 for Del default admin user (i.e. User ID
10.
Delete Admin Key – # = 11111 and Password =
Users Enter user ID then # 12345)
Enter password
Key – #
8
Key – *94 Door open time can be set for all
Door open time Enter door open time doors 1 to 98 secs.
11. Key – # And DOTL sense time is equal to
Door open time + 1 sec.
Key – *96
Press – 1 for Enable After pressing 1, Enter facility
Press – 3 for Disable code location & show card. Then
12. Facility code Press – # # facility code will come
Enter Facility code automatically for that card. Max
location (0-7) 8 facility codes can be assigned.
Show card
Key – #
Key – *97 1 = Weigand Access
Then select controller type 3 = Weigand Att.
13. Set Controller for reader 1 by selection 5 = Weigand Att. No check
Type keys from 1 to 8, and then 6 = Deny list
press # key. Same way set
controller type for reader 2
to 8 same as above.
Key – *990
Enter Unit IP Address
Press – # We can set Unit IP, Subnet mask,
Enter Subnet mask Default gateway, Server IP, Port
Press – # No. using this menu.
14. Set IP Address Enter Default gateway
Press – # After setting all parameters
Enter Server IP reset the system to take
Address effect.
Press – #
Enter Port No.
Press – #
System parameters: -
Terminal ID
IP Address
Net Mask
Gateway
Display Current Key – *991 Server IP
15. System Press Enter key to get Port Number
Parameters next data Global Msg
Banner Msg
Cont. In Out
Identify Mode
Controller Type
User name loc
Memory mgmt , etc.
9
After setting card format to 5-
Key – *995 Digit it will display and process
Press – 5 for 5-Digit 5-Digit card no.
Set 5/8/10 Digit Press – 8 for 8-Digit And for 10-Digit format, it will
16. card no format Press – Any Num Key except display and process 10-Digit
5 & 8 for 10-Digit Card no. Refer note
Key – # For 8 digit card no it will
display 5 digit card no & 3 digit
facility code.
Key – *996
17. Controller No Enter Controller No to We can set unique controller no
be set (0 - 9999) using this menu.
Key – #
Model Number
Unit ID
Controller No
Card Buffer
Used Card Buffer
Bal. Card Buffer
Key-*9991 Trans Buffer
18. System Info Press enter key to get next Used Trans Buff
data Bal Trans Buff
Serial No
Manufacturing Date
FW Compile Date
Firmware Version
Hardware Version
Controller Type
Reader Type
MAC address
Key-*9993 For card addition & deletion
19. Bulk Add card Press – 1 for add cards only show card, it will
Press – 3 for delete cards automatically get added or
delete from controller.
To enable disable fire &
Tamper press following keys,
0 = Disable All
Key – *9994 1 = Enable Fire
Use Keys 0, 1, 2 or 3 to 2 = Enable Tamper
20. Fire/Tamper enable disable fire & tamper. 3 = Enable Fire Tamper 1 = Enable Fire
Then press # 4 = Enable Intrusion
5 = Enable Fire and Intrusion
6 = Enable Intrusion and
Tamper
7 = Enable All
10
Key – *9997 To download transaction data
Press # from particular PC.
21. MAC Security Press– 1 for Enable Required to set MAC ID of that
Press – 3 for Disable PC from s/w.
Then press #
Key- *99990 To Ping Network
22. Network Ping Network ping 1= Ping gateway
2= Ping Internet
Key – *999990 By enabling system do not give
Press # access by any door till any
23. En/Dis D.I.S. Press– 1 for Enable door is open.
Press – 3 for Disable
Then press #
Note:
1. All add user, del user, …. Functions (3 to 23) are done in Admin mode.
2. Auto Logoff for Admin after 60 secs. (If any key is not pressed)
3. If system is initialized or IP address is set then reset the system.
4. For 26 bit reader you can set *995 keypad menu to 5 digit, 8 digit & 10 digit
card as per requirement.
5. For 32, 34 & 35 bit reader set *995 keypad menu to 5 digit & 10 digit only.
Annexure: 1
*90 Selective Initialization of System
00 Delete all data Every Info is deleted and set to default value
02 Delete All Users All users i.e. card buffer are deleted
03 Set All Default Deletes all info and set it to default value, except card buffer and
transactions
04 Delete Sys. Info Deletes current system parameter and set all with default system
parameter
05 Delete Time Zone Deletes all time zones and set default time zone
07 Delete Facility Code Facility codes are deleted and all are set to default Facility code
08 Delete Door info Deletes door information and set to default Door information
11
Annexure 2:
*9991 System Info
Model Number SMNG480
Unit ID 1
Controller No 0
Card Buffer 30000
Used Card Buffer 0
Bal. Card Buffer 30000
Trans Buffer 59999
Used Trans Buff 1
Bal Trans Buff 59998
Serial No As per factory setting
Manufacture Date As per factory setting
FW Compile Date 31 May 2014
Firmware Version N8R3.5A
Hardware Version 1.1
Controller Type Weigand Access
Reader Type 0
MAC Address As per factory setting
12
NG 4DR8RD CONNECTION DETAILS:
EXT1+
EXT2+
EXT1-
EXT2-
TAMP
TAMP
TAMP
TAMP
12V
12V
LED
LED
12V
12V
LED
LED
F+
D0
D0
D1
D1
D0
D0
F-
D1
D1
BZ
BZ
I+
BZ
BZ
I-
G
G
G
J5 J6
C J26 J28 J20 J25 J23 C
NC NC
TAMPER
NO NO J12
EG+ EG+
JP7
EG- Door 2 EG-
MC+ JP6 Door 3
MC+ GND
MC- MC-
RS485
BZ+ D-
BZ+
BZ- BZ- D+
C C
NC NC
J33
J4 J7
NO NO
EG+ EG+
EG-
JP8
Door 1 Door 4 EG-
MC+ JP5 MC+
MC- MC- J2
BZ+ BZ+
BZ- BZ-
J22 J24 J3 J8 J29 J27
TCP comm.
TAMP
TAMP
TAMP
TAMP
GNDL
GND
12VL
12V
12V
12V
12V
12V
LED
LED
LED
LED
D1
D0
D1
D0
BZ
D0
D1
BZ
D0
D1
BZ
BZ
G
G
G
G
Digital Lock
Reader 1 Reader 2 Reader 8 Reader 7
supply supply
13
Connector Details:
Sr. no Signal
1. C Weigand Readers connection (1 to 8):
2. NC
3. NO Sr. no Signal
1. 12V
Door Connection (1 to 4): 2. GND
3. D0
Sr. no Signal 4. D1
1. EG+ 5. BZ
2. EG- 6. LED
3. MC + 7. TMP
4. MC-
5. BZ+
6. BZ-
C
C NC
NC NO
Strike + EG+
NO
EG-
EG+ latch
+ - MC+
EG-
MC-
MC+
BZ+
MC-
- BZ+
BZ-
BZ-
12VL
12VL GNDL
GNDL J8
J8
14
RECOMMENDED CABLE SPECIFICATION
Particular Distance Cable Specs
Access controller to Weigand Up to 80 mtr 14/36, 22AWG, 6 core shielded
reader cable
Egress /Exit Up to 80 mtr 7/38, 22AWG, 2 core cable
Magnetic contact Up to 80 mtr 7/38, 22AWG, 2 core cable
Magnetic Lock Up to 80 mtr 14/36, 22AWG, 2 core cable
X
15
Connecting to the Host computer
The Smart XS NG provides various means to connect to the host computer such as:
1. through TCP/IP (Ethernet)
Connecting via TCP/IP
The Smart XS NG series can be connected on the LOCAL AREA NETWORK (LAN) Or Wide
Area Network (WAN) as under:
Step 1 Use the crossover network cable, with one end connected to the Smart XS NG TCP/IP
port, and the other end to your PC network adapter.
Step 2 To check your PC’s IP Address Settings, find out the IP address of the network. To do
so, go to a PC in the network presently, press Start -> Run -> Type “command” and click on
‘OK’.
Step 3 Type “ipconfig” and press ‘Enter’.
Step 5 To Check the IP Address of controller press *2 enter user id (11111) then # Enter
Password (12345) Key – # which will display the Current IP Address to Controller, make a
note of it. (Default IP of the controller is 192.168.000.200)
Step 6 To change the IP Address in Controller unit. Refer Configuration of Smart XS NG (port
is default 01234 no need to change)
Step 2 Type “Ping 192.168.0.251 -t” (The IP Address should reflect that of your Smart XS NG
unit)
Note: - If unsuccessful, either “Destination Host Unreachable” or “Request Timed Out” will be
displayed, please follow the above steps carefully and test the connection.
16
Successful Connectivity
Unsuccessful connectivity
Using Smart XS NG
The user enrollment process is performed in one of the Smart XS NG Unit OR through the
administrator’s computer, and the card data is distributed to other controllers over the Smart
XS NG Network
17
Trouble Shooting
# 1. No Communication from Smart XS NG Controller to PC
There are a few points that can be checked to fix it:
1) Make sure the network cable is functional; sometimes a damaged cable may be the cause of
all problems. To check if it is functional, make sure there are no loose ends and the jack is
properly attached to the cable.
2) Check that the IP Address Assignment matches the network settings of the corporate LAN
or the PC being used.
3) Make sure no IP has clashed and that there are no two identical IP addresses in the
network.
# 5. When the card is flashed in display its show “user not found”
To Enter into Admin Mode Refer keypad function details.
Check for controller Key – *5
Show card
Key – #
If user is added then it will show card no enrolled.
# 8. Using Stand Alone (Bio metrics device or Smart Single) Controller as weigand
reader then what will be to step follow-up?
Change controller type
Change weigand bit in transparent mode
Change reader IN/OUT setting as weigand out mode
All changes done by using key function.
18