Classification of Gas Turbine Power Plant
Classification of Gas Turbine Power Plant
Classification of Gas Turbine Power Plant
INTRODUCTION:
The gas turbine obtains its power by utilizing the energy of burnt gases and air, which is at high
temperature and pressure by expanding through the several ring of fixed and moving blades. It
thus resembles a steam turbine. To get a high pressure (of the order of 4 to 10 bar) of working
fluid, which is essential for expansion a compressor, is required.
The quantity of the working fluid and speed required are more, so, generally, a centrifugal or an
axial compressor is employed. The turbine drives the compressor and so it is coupled to the
turbine shaft. If after compression the working fluid were to be expanded in a turbine, then
assuming that there were no losses in either component the power developed by the turbine
would be just equal to that absorbed by the compressor and the work done would be zero. But
increasing the volume of the working fluid at constant pressure, or alternatively increasing the
pressure at constant volume can increase the power developed by the turbine. Adding heat so that
the temperature of the working fluid is increased after the compression may do either of these.
To get a higher temperature of the working fluid a combustion chamber is required where
combustion of air and fuel takes place giving temperature rise to the
working fluid.
Since the compressor is coupled with the turbine shaft, it absorbs some of the power produced by
the turbine and hence lowers the efficiency. The network is therefore the difference between the
turbine work and work required by the compressor to drive it.
Gas turbines have been constructed to work on the following: oil, natural gas, coal gas, producer
gas, blast furnace and pulverized coal.
The gas turbine power plants which are used in electric power industry are classified into two
groups as per the cycle of operation.
(a) Open cycle gas turbine.
(b) Closed cycle gas turbine.
74
OPEN CYCLE GAS TURBINE POWER PLANT
A simple open cycle gas turbine consists of a compressor, combustion chamber and a turbine as
shown in Fig. 2.10. The compressor takes in ambient air and raises its pressure. Heat is added to
the air in combustion chamber by burning the fuel and raises its temperature.
The heated gases coming out of combustion chamber are then passed to the turbine where it
expands doing mechanical work. Part of the power developed by the turbine is utilized in driving
the compressor and other accessories and remaining is used for power generation. Since ambient
air enters into the compressor and gases coming out of turbine are exhausted into the atmosphere,
the working medium must be replaced continuously. This type of cycle is known as open cycle
gas turbine plant and is mainly used in majority of gas turbine power plants as it has many
inherent advantages.
(A) Advantages
1. Warm-up time. Once the turbine is brought up to the rated speed by the starting motor
and the fuel is ignited, the gas turbine will be accelerated from cold start to full load
without warm-up time.
2. Low weight and size. The weight in kg per kW developed is less.
3. Fuels. Almost any hydrocarbon fuel from high-octane gasoline to heavy diesel oils can
be used in the combustion chamber.
4. Open cycle plants occupy comparatively little space.
5. The stipulation of a quick start and take-up of load frequently are the points in favour of
open cycle plant when the plant is used as peak load plant.
75
6. Component or auxiliary refinements can usually be varied to improve the thermal
efficiency and give the most economical overall cost for the plant load factors and other
operating conditions envisaged.
7. Open-cycle gas turbine power plant, except those having an intercooler, does not require
cooling water. Therefore, the plant is independent of cooling medium and becomes self-
contained.
(B) Disadvantages:
1. The part load efficiency of the open cycle plant decreases rapidly as the considerable
percentage of power developed by the turbine is used to drive the compressor.
2. The system is sensitive to the component efficiency; particularly that of compressor. The
open cycle plant is sensitive to changes in the atmospheric air temperature, pressure and
humidity.
3. The open-cycle gas turbine plant has high air rate compared to the other cycles, therefore,
it results in increased loss of heat in the exhaust gases and large diameter ductwork is
necessary.
4. It is essential that the dust should be prevented from entering into the compressor in order
to minimize erosion and depositions on the blades and passages of the compressor and
turbine and so impairing their profile and efficiency. The deposition of the carbon and
ash on the turbine blades is not at all desirable as it also reduces the efficiency of the
turbine.
Closed cycle gas turbine plant was originated and developed in Switzerland. In the year 1935, J.
Ackeret and C. Keller first proposed this type of machine and first plant was completed in Zurich
in1944.
It used air as working medium and had a useful output of 2 mW. Since then, a number of closed
cycle gas turbine plants have been built all over the world and largest of 17 mW capacity is at
Gelsenkirchen, Germany and has been successfully operating since 1967. In closed cycle gas
turbine plant, the working fluid (air or any other suitable gas) coming out from compressor is
heated in a heater by an external source at constant pressure. The high temperature and high-
pressure air coming out from the external heater is passed through the gas turbine. The fluid
coming out from the turbine is cooled to its original temperature in the cooler using external
cooling source before passing to the compressor.
76
The working fluid is continuously used in the system without its change of phase and the
required heat is given to the working fluid in the heat exchanger.
The arrangement of the components of the closed cycle gas turbine plant is shown in Fig.2.11
(A) Advantages
1. The inherent disadvantage of open cycle gas turbine is the atmospheric backpressure at
the turbine exhaust. With closed cycle gas turbine plants, the backpressure can be increased.
Due to the control on backpressure, unit rating can be increased about in proportion to the
backpressure. Therefore the machine can be smaller and cheaper than the machine used
to develop the same power using open cycle plant.
2. The closed cycle avoids erosion of the turbine blades due to the contaminated gases and
fouling of compressor blades due to dust. Therefore, it is practically free from deterioration of
efficiency in service. The absence of corrosion and abrasion of the interiors of the
compressor and turbine extends the life of the plant and maintains the efficiency of the plant
constant throughout its life as they are kept free from the products of combustion.
3. The need for filtration of the incoming air which is a severe problem in open cycle plant
is completely eliminated.
4. Load variation is usually obtained by varying the absolute pressure and mass flow of the
circulating medium, while the pressure ratio, the temperatures and the air velocities
remain almost constant.
This result in velocity ratio in the compressor and turbine independent of the load and full load
thermal efficiency maintained over the full range of operating loads.
5. The density of the working medium can be maintained high by increasing internal pressure
range, therefore, the compressor and turbine are smaller for their rated output. The high
density of the working fluid further increases the heat transfer properties in the heat
exchanger.
6. As indirect heating is used in closed cycle plant, the inferior oil or solid fuel can be used in
the furnace and these fuels can be used more economically because these are available in
abundance.
7. Finally the closed cycle opens the new field for the use of working medium (other than
air as argon, CO2, helium) having more desirable properties. The ratio γ of the working fluid
plays an important role in determining the performance of the gas turbine plant. An
increase in γ from 1.4 to 1.67 (for argon) can bring about a large increase in output per kg
of fluid circulated and thermal efficiency of the plant.
The theoretical thermal efficiencies of the monoatomic gases will be highest for the closed
cycle type gas turbine. Further, by using the relatively dense inert gases, such as argon,
krypton and xenon, the advantage of smaller isentropic heat fall and smaller cross- sectional
flow areas would be realised: Whether CO2 or Helium should be adopted as working
medium is matter of controversy at present. Blade material poses a problem to use
helium as working fluid. In case of CO2, a new kind of compressor must be designed to
compress the fluid. The main advantage of CO2 is that it offers 40% efficiency at 700°C
whereas helium would need 850°C or more to achieve the same efficiency. A helium turbine
would also need to run faster imposing larger stresses on the rotor.
77
Fig-2.11-Closed Cycle
8. The maintenance cost is low and reliability is high due to longer useful life.
9. The thermal efficiency increases as the pressure ratio (Rp) decreases. Therefore, appreciable
higher thermal efficiencies are obtainable with closed cycle for the same maximum and
minimum temperature limits as with the open cycle plant.
10. Starting of plane is simplified by reducing the pressure to atmospheric or even below
atmosphere so that the power required for starting purposes is reduced considerably.
Disadvantages
78
The closed cycle is only preferable over open cycle where the inferior type of fuel or solid fuel is
to be used and ample cooling water is available at the proposed site of the plant.
It has been found that a considerable amount of heat energy goes as a waste with the exhaust of
the gas turbine. This energy must be utilized. The complete use of the energy available to a
system is called the total energy approach. The objective of this approach is to use all of the heat
energy in a power system at the different temperature levels at which it becomes available to
produce work, or steam, or
the heating of air or water, thereby rejecting a minimum of energy waste. The best approach is
the use of combined cycles.
There may be various combinations of the combined cycles depending upon the place or country
requirements. Even nuclear power plant may be used in the combined cycles.
Fig-2.12-Combined Cycle
Fig.2.12 shows a combination of an open cycle gas turbine and steam turbine. The exhaust of gas
turbine which has high oxygen content is used as the inlet gas to the steam generator where the
combustion of additional fuel takes place. This combination allows nearer equality between the
power outputs of the two units than is obtained with the simple recuperative heat exchanger. For
a given total power output the energy input is reduced (i.e., saving in fuel) and the installed cost
of gas turbine per unit of power output is about one-fourth of that of steam turbine. In other
words, the combination cycles exhibit higher efficiency. The greater disadvantages include the
complexity of the plant, different fuel requirements and possible loss of flexibility and reliability.
The most recent technology in the field of co-generation developed in USA utilizes the gaseous
fuel in the combustion chambers produced by the gasification of low quality of coal. The system
is efficient and the cost of power production per kW is less.
79
APPLICATIONS OF GAS TURBINE
1. Gas turbine plants are used as standby plants for the hydro-electric power plants.
2. Gas turbine power plants may be used as peak loads plant and standby plants for smaller power
units.
3. Gas turbines are used in jet aircrafts and ships. Pulverised fuel fired plants are used in locomotive.
The economics of power generation by gas turbines is proving to be more attractive, due to low
capital cost, and high reliability and flexibility in operation. Quick starting and capability of
using wide variety of fuels from natural gas to residual oil or powdered coal are other
outstanding features of gas turbine power plants. Major progress has been made in three
directions namely increase in unit capacities of gas turbine units (50—100 mW), increase in their
efficiency and drop in capital cost, (about Rs. 700 per kW installed). Primary application of gas
turbine plant is to supply peak load. However gas turbine plants now-a-days are universally used
as peak load, base lead as well as standby plants.
1. It is smaller in size and weight as compared to an equivalent steam power plant. For smaller
capacities the size of the gas turbine power plant is appreciably greater than a high speed
diesel engine plant but for larger capacities it is smaller in size than a comparable diesel
engine plant. If size and weight are the main consideration such as in ships, aircraft engines
and locomotives, gas turbines are more suitable.
2. The initial cost and operating cost of the plant is lower than an equivalent steam power plant.
A thermal plant of 250 mW capacity cost about Rs. 250 crores. Presently whereas a gas
turbine plant of that same-size cost nearly 70 crores.
3. The plant requires less water as compared to a condensing steam power plant.
4. The plant can be started quickly, and can be put on load in a very short time.
5. There are no standby losses in the gas turbine power plant whereas in steam power plant these
losses occur because boiler is kept in operation even when the turbine is not supplying any
load.
6. The maintenance of the plant is easier and maintenance cost is low.
7. The lubrication of the plant is easy. In this plant lubrication is needed mainly in
compressor, turbine main bearing and bearings of auxiliary equipment.
8. The plant does not require heavy foundations and building.
9. There is great simplification of the plant over a steam plant due to the absence of boilers with
their feed water evaporator and condensing system.
DISADVANTAGES:
1. Major part of the work developed in the turbine is used to derive the compressor. Therefore,
network output of the plant is low.
2. Since the temperature of the products of combustion becomes too high so service
conditions become complicated even at moderate pressures.
80