TDS 46682 Essence Easy Wipe (New) Euk ID PDF

Technical Data Sheet
^(ValidationDate) 46682 46682 5 1

ID Approved Other
Essence Easy Wipe(New)
Product description
Type
An interior special acrylic emulsion paint that gives good washability. Available in matt finish.
Features and benefits

Washable - Walls are easy to maintain and keep clean.
Low Odour - Paint odour is low during and after application making the property ready for occupancy in shorter
period.
Anti-Fungal - Inhibit the growth of fungus.
Low VOC - Pass international & local green coating standards.
Easy to Apply - Effortless application that saves time.
Good Hiding - Provides good hiding power to conceal wall imperfections.
Formulated Without Harmful Chemicals - Free from harmful chemicals and emissions such as APEO,
formaldehyde and heavy metals.
Recommended use
For interior application, suitable for new buildings and repainting.
Substrate
On concrete, masonry, plaster, brick work and soft board surfaces.
Product data
Packaging size Packing may vary from country to country according to local requirements.
Colours As per colour card and available in Jotun Multicolor tinting system (Interior range).
Solids by volume 37 ± 2 volume%
VOC for Ready-for-Use EU limit value for the product (cat. A/a): 30 g/l. The product contains max 50 g/l
Mixture VOC.
Application data
Application equipment / methods
By brush, roller, airless spray or conventional spray.
Guiding data for airless spray

Nozzle tip 0.021–0.027"
Spray angle degrees 65–80°
Pressure at nozzle 140 - 190 kg/cm² (2100 psi)
Date of issue: 14.09.2022 Product code: 46682 Page: 1/4
This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) for this product.
For your nearest local Jotun office, please visit our website at www.jotun.com.
1

Spreading rate per coat

Theoretical 9.3 m²/l - 12.3 m²/l
Spreading rate depends on film thickness applied, type of texture, surface porosity, imperfections, temperature,
wastage during painting etc.
Recommended film thickness per coat

Wet 81 µm - 108 µm
Dry 30 µm - 40 µm
Film thickness will vary and is calculated as average.
Thinner
Water
Dilution
The paint is ready to use after proper stirring. If thinning is required, water may be added up to a maximum of
5%.
Conditions during application

Apply at a temperature between 10°C - 35°C.
The temperature of the substrate should be minimum 3°C above the dew point of the air. The temperature and
the relative humidity should be measured in the vicinity of the substrate. Good ventilation is usually required in
confined areas to ensure proper drying.
Drying times
Drying times are generally related to air circulation, temperature, film thickness and number of coats, and will
be affected correspondingly. The figures given in the table are typical with:
Good ventilation (Outdoor exposure or free circulation of air)
Typical film thickness
One coat on top of inert substrate
The given data must be considered as guidelines only. The actual drying time and time before recoating may be
shorter or longer, depending on the ambient temperature, film thickness, ventilation, humidity, underlying paint
system, requirement for early handling and mechanical strength etc.
1. Recommended data given is, for recoating with the same generic type of paint.
2. In case of multi-coat application, drying times will be influenced by the number and sequence and by the
total thickness of previous coats applied.
3. The surface should be dry and free from any contamination prior to application of the subsequent coat.
The drying time is measured by stated values:

Relative Humidity (RH) 50 %
Substrate temperature 10 °C 23 °C 40 °C
Surface (touch) dry 2h 1h 0.5 h

Hard dry 8h 6h 4h
Dry to over coat, minimum 4h 2h 1h

1

Directions for use

Surface preparation
The substrate must be sound, clean, dry, free from dust, oil, grease and laitance etc. All traces of release agents
must be removed. On chalky and dusty surfaces, all loose material must be removed by stiff bristle brushing.
Any defects in the substrate like surface undulations, cracks, pin holes etc., should be rectified/filled before
starting painting. Other surfaces: The coating may be used on other substrates. Please contact your local Jotun
office for more information.
Recommended paint system
Primer
Jotun Essence Easy Primer : 1 coat
Topcoat
Essence Easy Wipe(New) : 2 coats
Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.
Certificates
Complies to Singapore Green Label
Tests
Volume Solids % measured according to ISO 3233:1998 (E).
Fungus Resistance Test measured according to SS 150 : 2015 (Annex A: Mildew Resistance Test)
Wet Scrub Resistance Test measured according to SS5 Part F5: 2003 (2013)
Health and safety

Please observe the environmental and precautionary notices displayed on the container.
A Material Safety Data Sheet for the product has been issued.
Detailed information regarding health and safety risks and precautions for the use of this product is specified in
the product's Safety Data Sheet.
First-aid measures, refer to section 4.
Handling and storage, refer to section 7.
Transport information, refer to section 14.
Regulatory information, refer to section 15.

1

Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.
Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.
If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.


TDS 46682 Essence Easy Wipe (New) Euk ID PDF

Uploaded by

Copyright:

Available Formats

TDS 46682 Essence Easy Wipe (New) Euk ID PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TDS 46682 Essence Easy Wipe (New) Euk ID PDF

Uploaded by

Copyright:

Available Formats

Technical Data Sheet

^(ValidationDate) 46682 46682 5 1

Essence Easy Wipe(New)

Features and benefits

Anti-Fungal - Inhibit the growth of fungus.

Low VOC - Pass international & local green coating standards.

Easy to Apply - Effortless application that saves time.

Good Hiding - Provides good hiding power to conceal wall imperfections.

Solids by volume 37 ± 2 volume%

Guiding data for airless spray

Date of issue: 14.09.2022 Product code: 46682 Page: 1/4

This Technical Data Sheet supersedes those previously issued.

Technical Data Sheet

Spreading rate per coat

Recommended film thickness per coat

Film thickness will vary and is calculated as average.

Conditions during application

The drying time is measured by stated values:

Surface (touch) dry 2h 1h 0.5 h

Date of issue: 14.09.2022 Product code: 46682 Page: 2/4

This Technical Data Sheet supersedes those previously issued.

Technical Data Sheet

Directions for use

Recommended paint system

Health and safety

Date of issue: 14.09.2022 Product code: 46682 Page: 3/4

This Technical Data Sheet supersedes those previously issued.

Technical Data Sheet

Date of issue: 14.09.2022 Product code: 46682 Page: 4/4

This Technical Data Sheet supersedes those previously issued.

You might also like