TDS Jotun Block Filler-1

Technical Data Sheet
^(ValidationDate) 4254 4254 5 1

AE - EG - KW - OM - QA - SA - TR Approved Other
Jotun Block Filler
Product description
Type
This product is an exterior grade filler. Based on acrylic copolymer emulsion.
Features and benefits

Provides an excellent base for subsequent coats. Easy application.
Recommended use
Can be used as a filler to minimize surface imperfections.
Substrate
Cement plaster, concrete, block work, rendered surfaces, gypsum board etc.
Substrate should have sufficient strength to receive the paint. Any defects in the substrate like surface
undulations, cracks, pin holes etc., should be rectified/filled before starting painting.
Product data
Packaging size 18L
Egypt and Libya : 10 L and 20L.
Turkey and Saudi : 25 kg
Colours Off White
Solids by volume 62 ± 2 volume% Theoretical
Specific gravity 1.85 Theoretical
VOC 14 g/l ISO 11890 EU

VOC comments This is the theoretical value. Tested value will vary depending on test methodology,
accuracy of equipment used for testing and test conditions.
Application data
Application equipment / methods
Trowel, pallet knife or other suitable dispenser.
The product can be applied by

Trowel, pallet knife or other suitable dispenser.
Cleaning of painting tools

Water
Date of issue: 04.04.2019 Product code: 4254 Page: 1/3
This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) for this product.
For your nearest local Jotun office, please visit our website at www.jotun.com.
1

Jotun Block Filler
Film thickness per coat

Typical recommended range
Dry film thickness 100 - 2000 µm
Wet film thickness 160 - 3225 µm
Film thickness will vary and is calculated as average.
Theoretical spreading rate 6.2 - 0.3 m²/l
Spreading rate depends on film thickness applied, type of texture, surface porosity, imperfections, temperature,
wastage during painting etc.
Maximum spread rate per coat is obtained at minimum dry film thickness and vice versa.
Thinner
Water
Dilution
Maximum 10 %
Conditions during application

The temperature of the substrate should be minimum 10 °C and at least 3 °C above the dew point of the air,
measured in the vicinity of the substrate. Good ventilation is usually required in confined areas to ensure proper
drying.
Drying times
Drying times are generally related to air circulation, temperature, film thickness and number of coats, and will
be affected correspondingly.
1. Recommended data given is, for recoating with the same generic type of paint.
2. In case of multi-coat application, drying times will be influenced by the number and sequence and by the
total thickness of previous coats applied.
3. The surface should be dry and free from any contamination prior to application of the subsequent coat.
The drying time is measured by stated values:

Relative Humidity (RH) 50 %
Substrate temperature 10 °C 23 °C 40 °C
Surface (touch) dry 6h 3h 1h

Hard dry 16 h 8h 6h
Dry to over coat, minimum 16 h 8h 6h
Directions for use

Surface preparation
The substrate must be sound, clean, dry and free from dust, oil, grease, laitance etc. All traces of form release
agents/curing agents must be removed. A light sanding with suitable abrasive material is recommended before
application. Any resulting dust/loose particles must be removed.
Recommended paint system
Primer
Suitable primer.

1

Jotun Block Filler
Undercoat
Jotun Block Filler : 1 or 2 Coats
Topcoat
Recommended paint system
Remarks
Other systems may be specified, depending on area of use.
Contents of packaging with different batch numbers must be mixed together before use.
Please refer to the Decorative Sales Department for technical advice.
If any Block filler is used to rectify imperfections on the substrate, proper sanding followed by a full undiluted
coat of Penetrating Sealer must be used before applying any Jotashield textures.
Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.
Health and safety

Please observe the environmental and precautionary notices displayed on the container.
A Material Safety Data Sheet for the product has been issued.
Detailed information regarding health and safety risks and precautions for the use of this product is specified in
the product's Safety Data Sheet.
First-aid measures, refer to section 4.
Handling and storage, refer to section 7.
Transport information, refer to section 14.
Regulatory information, refer to section 15.
Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.
Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.
If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.


TDS Jotun Block Filler-1

Uploaded by

Copyright:

Available Formats

TDS Jotun Block Filler-1

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TDS Jotun Block Filler-1

Uploaded by

Copyright:

Available Formats

Technical Data Sheet

^(ValidationDate) 4254 4254 5 1

Jotun Block Filler

Features and benefits

Solids by volume 62 ± 2 volume% Theoretical

Specific gravity 1.85 Theoretical

VOC 14 g/l ISO 11890 EU

The product can be applied by

Cleaning of painting tools

Date of issue: 04.04.2019 Product code: 4254 Page: 1/3

This Technical Data Sheet supersedes those previously issued.

Technical Data Sheet

Film thickness per coat

Conditions during application

The drying time is measured by stated values:

Surface (touch) dry 6h 3h 1h

Directions for use

Recommended paint system

Date of issue: 04.04.2019 Product code: 4254 Page: 2/3

This Technical Data Sheet supersedes those previously issued.

Technical Data Sheet

Please refer to the Decorative Sales Department for technical advice.

Health and safety

Date of issue: 04.04.2019 Product code: 4254 Page: 3/3

This Technical Data Sheet supersedes those previously issued.

You might also like