5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

Slide2 User Guide

Quick Start Tutorial

1. Introduction
This Quick Start tutorial will demonstrate some of the basic features of Slide2. You will see
how quickly and easily a model can be created and analyzed with Slide2. All tutorial files
installed with Slide2 can be accessed by selecting File > Recent > Tutorials folder from the
Slide2 main menu. The finished product of this tutorial can be found in the Tutorial 01 Quick
Start.slmd data file.

Open Slide2 by double-clicking the Slide2 icon. When Slide2 model program is started, a
new blank document will open, allowing you to begin creating a model immediately.

Your window should look like the following:

Throughout this tutorial, we will be referring to four common interface locations as a

reference for locating buttons and icons that will be necessary to complete the tutorial.

The Sidebar, pictured below, is located on the left of the screen.

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 1/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

The Toolbar, shown below, is located at the top of the window beneath the menu bar and
workflow tabs.

Workflow Tabs are also located at the top of the window.

Lastly, is the Prompt Line, which is located at the bottom right corner of the window right
above the SNAP icon.

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 2/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

2. Project Settings
Before creating any model, you should first make sure the main analysis parameters (Failure
Direction, Units of Measurement, Analysis Methods, etc.) are well defined. This is done in the
Project Settings dialog. Although we will not be changing the default parameters for this
tutorial, let's take a look at the dialog so that you can become accustomed to using it.

Go to Project Settings by following the steps:

Select: Analysis > Project Settings.

The Project Settings dialog is organized into various pages which are accessed by selecting
the name of the page from the list at the left of the dialog.

1. On the General page, make sure that the Stress Units option is set to Metric.

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 3/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

2. Select the Scenarios page. Note that by default it is set to Multiple Scenario Modelling
which will be discussed later in this tutorial.

3. Do not change any other setting in the dialog. Select OK.

Before moving on to creating the model, let's give the project a title.

1. Select Analysis > Project Summary.

2. Enter "Quick Start Tutorial" as also seen in the figure below. Once you've finished
entering the title, select OK to save and close the dialog.

3. Boundaries
The first boundary that must be defined for every Slide2 model is the External Boundary.
The External Boundary in Slide2 is a closed polyline encompassing the soil region you wish
to analyze. In general:

The uppermost segments of the External Boundary represent the slope surface

All other segments of the External Boundary are arbitrary and can be extended as far
out as necessary for a complete analysis of the problem

1. To add the External Boundary, select Add External Boundary from the toolbar or
the Boundaries menu.

Select: Boundaries > Add External Boundary

2. Enter the following coordinates in the prompt line at the bottom right of the screen,
pressing Enter after each coordinate. As you enter the coordinates, notice that the view
limits are automatically updated to encompass the coordinates you are entering:

(0,0); (130,0); (130,50); (80,50); (50,30); (0,30)

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 4/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

3. Once you have finished typing the coordinates above enter the letter "c" and your
boundary should look like the following:

Entering "c" after the last vertex automatically connects the first and last vertices (closes the
boundary), and exits the Add External Boundary option.

TIP: If you make a mistake while entering coordinates, you can enter "u" in the prompt line at
any time, to undo the most recent vertex entry.

If your model seems too big or too small, you can try using the Zoom All function

Select: Zoom All (or press F2) to zoom the model to the center of the view.

As a shortcut, various options are available by entering single letter text commands in the
prompt line . These options are also available in the right-click context menu, and include:

Undo (enter "u" to undo the last vertex)

Arc (enter "a" to open Arc Options)

Circle (enter "i" to open Circle Options)

Relative Coordinates (enter "@" to switch between Absolute Coordinates, Relative

Distance and Polar Coordinates)

Ratio (enter "r" ...)

Snap Options

Coordinate Table - The Coordinate Table option allows you to enter or paste coordinates
into a dialog. The coordinate table can be accessed by entering "t" in the prompt line, or
from the right-click menu.

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 5/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

Boundaries can be entered graphically in Slide2 by simply clicking the left mouse button
at the desired coordinates. The Snap options can be used for entering exact
coordinates graphically.

4. Slip Surfaces
Slide2 can analyze the stability of either circular or non-circular slip surfaces. Individual
surfaces can be analyzed or a critical surface search can be performed to attempt to find
the slip surface with the lowest factor of safety.

In this tutorial, we will perform a critical surface search for a circular slip surface. In Slide2,
there are three search methods available for circular slip surfaces.

Auto Refine Search

Grid Search

Slope Search

By default, Slide2 uses the Auto Refine Search method to find the critical slip surface.
However, we will switch to the Grid Search method, which is a commonly used and well-
known search method for circular slip surfaces.

1. Select the Surfaces workflow tab.

Select: Surfaces > Surface Options

2. Change the Search Method to Grid Search then hit OK.

AUTO GRID
A Grid Search requires a grid of slip centers.

Slip center grids can be user-defined by selecting the Add Grid option or can be
automatically created by selecting the Auto Grid option. For this tutorial, we will use the Auto
Grid option.

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 6/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

Select: Surfaces > Auto Grid

You will see the Grid Spacing dialog. We will use the default number of intervals in X and Y
Direction of (20x20). When the following dialog pops up just hit OK and the grid will be
created.

By default, the actual locations of the slip centers within the grid are not displayed. You can
turn them ON in Display Options. In the Sidebar, select the " Show Search Grid Points"
checkbox. (Display options can also be accessed from the toolbar or the right-click menu).

Your screen should look as follows

Note

The 20x20 grid interval spacing actually gives a grid of 21x21 = 441 slip centers.

Each center in a slip center grid, represents the center rotation of a series of slip circles.
Slide2 automatically determines the circle radii at each grid point, based on the Slope

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 7/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

Limits and the Radius Increment. The Radius Increment, entered in the Surface Options
dialog, determines the number of circles generated at each grid point.

How Slide2 performs a circular surface search, using the Slope Limits and the Radius
Increment, is discussed in the next section.

SLOPE LIMITS
When an External Boundary is created, two triangular markers are displayed at the left and
right limits of the upper surface. These are called Slope Limits. The Slope Limits are
automatically calculated by Slide2 as soon as the External Boundary is either created or
whenever editing operations (e.g. moving vertices) are performed.

The Slope Limits serve two purposes in a circular surface analysis:

Filtering - All slip surfaces must intersect the External Boundary, within the Slope Limits.
If the start and end points of a slip surface are NOT within the Slope Limits, then the slip
surface is discarded (i.e. not analyzed). This is illustrated below.

Circle Generation - The segments of the External Boundary between the Slope Limits
define the slope surface to be analyzed. The slope surface is used to generate the slip
circles for a Grid Search, as follow:

For each slip center grid point, suitable Minimum and Maximum radii are
determined, based on the distances from the slip center to the slope surface as
shown in the next figure.

The Radius Increment is then used to determine the number of slip circles
generated between the minimum and maximum radii circles at each grid point.

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 8/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

Note

The Radius Increment is the number of intervals between the minimum and
maximum circle radii at each grid point. Therefore the number of slip circles
generated at each grid point is equal to the Radius Increment +1.

The total number of slip circles generated by a Grid Search is therefore = (Radius
Increment +1) x ( (Total # of Grid Slip Centers). For this example, this equals
11x21x21 = 4851 slip circles.

The default Slope Limits calculated by Slide2 will, in general, give the maximum coverage for
a Grid Search. If you wish to narrow the Grid Search to more specific areas of the model, the
Slope Limits can be customized with the Define Limits dialog.

Select: Surfaces > Slope Limits > Define Limits

The Define Slope Limits dialog allows you to customize the left and right Slope Limits, or
even to define two sets of limits (e.g. to define allowable ranges for slip surfaces starting and
ending points).

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 9/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

We are using the default Slope Limits for this tutorial; it is suggested that the user
experiment with different Slope Limits, after completing this tutorial. Select Cancel in the
Define Slope Limits dialog.

TIP: The Slope Limits can also be moved graphically, using the mouse, with the Move Limits
option.

PROPERTIES
Now let's define the material properties.

Select: Properties > Define Materials

In the Define Material Properties dialog, select Material 1 and enter the following parameters:

Name = Soil 1

Unit Weight = 19
Strength Type = Mohr Coulomb

Cohesion = 5

Phi = 30

Water Surface = None

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 10/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

When you are finished entering the properties, select OK.

Note

Since we are dealing with a single material model and entered properties with the first
default material from the list in the dialog (Material 1), Slide2 automatically assigns
these properties to the entire model.

Recall when you first created the external boundary, the area inside the boundary was filled
with the same colour as Material 1. This is a visual indication that the external boundary is
assigned material properties from the first default material type.

For multiple material models, it is necessary for the user to assign properties with the Assign
Properties option. We will deal with assigning properties in Tutorial 2.

5. Analysis Methods

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 11/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

Before we run the analysis, let's examine the limit equilibrium Analysis Methods that are
available in Slide2.

Select: Analysis > Project Settings

1. Select the Methods page in the Project Settings dialog.

By default, the Vertical Slices option is selected, and Bishop and Janbu methods are the
selected Analysis Methods.

You may select any or all Vertical Slice analysis methods and all selected methods will be
used when Slide2 runs the analysis. See the Slide2 Help system for information about the
different analysis methods, and the assumptions used in each.

For this tutorial, we will only use the default vertical slice methods - Bishop and Janbu.

1. Select Cancel in the Project Settings dialog.

SAVE
Before we go further save as a file called Quick Start Tutorial. (Slide2 multi-scenario model
files have a *.slmd filename extension).

Select: File > Save

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 12/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

Use the Save As dialog to save the file.

DOCUMENT VIEWER
The Document Viewer in the sidebar allows you to create, organize and edit groups and
scenarios for multi-scenario files.

For this simple example, the file consists of only one group containing one scenario (the
master scenario)

We don't need to worry about the document viewer right now, but just keep it in mind for
future reference. Multi scenario modelling is discussed at the end of this tutorial and is
discussed in detail in Tutorial 24 and other Slide2 tutorials.

6. Compute
You are now ready to run the analysis.

Select: Analysis > Compute

The Slide2 Compute engine will proceed in running the analysis. This should only take a few
seconds. When completed, you are ready to view the results in Interpret.

7. Interpret
To view the results of the analysis:

Select: Analysis > Interpret

This will start the Slide2 Interpret program. You should see the results of the Grid Search as
shown in the following figure:

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 13/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

The Global Minimum slip surface and the contoured grid are both visible in the above
figure.

By default, when a computed file is first opened in Slide2 Interpret, you will always see:

The Global Minimum slip surface, for the BISHOP Simplified analysis method (if a
Bishop analysis was selected)

If a Grid Search has been performed, you will see contours of safety factor in the slip
center grid. The contours are based on the MINIMUM calculated safety factor at each
grid slip center.

GLOBAL MINIMUM SLIP SURFACES

For a given analysis method, the Global minimum slip surface is the slip surface with the
lowest factor of safety of all slip surfaces analyzed.

The analysis method is displayed in the toolbar at the top of the Slide2 Interpret window.

The Global Minimum safety factor is displayed beside the slip center for the surface. In this
case, for a Bishop analysis, the overall minimum safety factor is 1.141

To view the Global Minimum safety factor and surface for other analysis methods, simply use
the drop-list in the toolbar. For example, select the Janbu simplified method, and observe
the results. In general, the Global Minimum safety factor and slip surface can be different for
each analysis method.

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 14/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

TIP: While the analysis method is selected in the toolbar, you can scroll through the analysis
methods by rotating the mouse wheel. This allows you to quickly compare analysis results,
without having to select the analysis method each time.

It is very important to note the following:

The term "Global Minimum" should be used with caution. The Global Minimum surfaces
displayed after an analysis are dependent on your search techniques and may not
necessarily be the lowest possible safety factor for a given model. Depending on the
chosen search criteria (grid location, grid interval spacing, radius increment and slope
limits) lower safety factors may exist.

In this example, the Global Minimum surface is the same for both methods chosen.
However, this is not the case for other models which will not necessarily have the same
global minimum surface for each analysis method.

The display of the Global Minimum surface may be toggled on or off by selecting the Global
Minimum option from the toolbar or the Data menu.

Select: Data > Global Minimum

VIEWING MINIMUM SLIP SURFACES

Recall that the Grid Search is performed by generating circles of different radii at each grid
point in a slip center grid.

To view the minimum safety factor surface generated at each grid point, select the Minimum
Surfaces option in the toolbar or the Data Menu.

Select: Data > Minimum Surfaces

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 15/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

As shown in the above figure, Slide2 will draw the minimum slip surfaces, with colours
corresponding to the safety factor contours in the grid, and in the legend (visible in the
upper left corner).

Again, as with the Global Minimum, note that the Minimum Surfaces correspond to the
currently selected analysis method (i.e. if you select different analysis methods, you may see
different surfaces displayed)

VIEWING ALL SURFACES

To view all valid slip surfaces generated by the analysis, select the All Surfaces option from
the toolbar or the Data menu.

Select: Data > All Surfaces

Again, note that the slip surfaces are colour-coded according to safety factors and that the
safety factors will vary according to the analysis method chosen.

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 16/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

Note

Since the slip surfaces overlap, Slide2 draws the slip surfaces by starting with the
HIGHEST safety factors and ending with the LOWEST, giving priority to the lowest
safety factors (i.e. they are drawn last)

The All Surfaces option is very useful for visualizing all of the valid surfaces generated by
your analysis. It may indicate:

Areas in which to concentrate a search, in order to find a lower Global Minimum, using
some of the various techniques provided in (customizing Slope Limits, Focus Search
Option in Surfaces menu)

Areas which have been insufficiently covered by the search, again, necessitating a
change in the search parameters (e.g. location of the slip center grid, or a large value of
Radius Increment)

FILTER SURFACES
When displaying either the Minimum Surfaces or All Surfaces, as described above, you can
filter the surfaces you would like displayed using the Filter Surfaces option in the toolbar or
the Data menu.

Select: Data > Filter Surfaces

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 17/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

Filtering can be done by safety factor, or by a specified number of lowest surfaces (e.g. the
10 lowest safety factor surfaces). By toggling through each option Slide2 will automatically
update the surfaces to conform with current selected option.

For example, select the "Surface with a factor of safety below" option. Leave the default
safety factor value of 2. The display should automatically update as shown below.

Select Done to close the dialog.

DATA TIPS
The Data Tips feature in Slide2 allows you to obtain model and analysis information by
simply placing the mouse cursor over any model entity or location on the screen.

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 18/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

To enable Data Tips:

1. Click on the box on the Status Bar (located at the bottom of the window) which says
DATA TIPS.

2. By default, it should indicate MAX DATA TIPS. When you click on this box, it will toggle
through three different data tip models (OFF, MIN, MAX). Toggle until it displays MAX
DATA TIPS.

3. Now move the mouse cursor over the model and you will see that the material
properties of the soil are displayed, as shown below.

1. Place the cursor over different entities of the model, and see what information is
displayed.

Virtually all model information is available using Data Tips, for example:

slip surface safety factor, center and radius

vertex coordinates

grid coordinates

contour values within slip center grids

slope limit coordinates

support properties

1. Click on the Status Bar and toggle until it displays DATA TIPS OFF.

You can experiment with the Data Tips option in later tutorials.

Note

Data Tips can also be toggled through the View menu.

SHOW COORDINATES
Turn off the display of All Surfaces by re-selecting the toolbar button.

Select: Data > All Surfaces

Model coordinates can be displayed using the Data Tips option described in the previous
section. Model coordinates can also be displayed with the Show Coordinates option in the
View menu.

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 19/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

Select: View > Show Coordinates

1. In the Show Coordinates dialog, select the External Boundary checkbox and select
Close.

You will see the external boundary coordinates as shown below.

TIP: If the coordinates appear too small, right-click and select Display Options, and under
the General tab, clear the Scale Display Items checkbox. Display Options are also available in
the sidebar.

1. Go back to the Show Coordinates dialog and turn off the display of coordinates by
clearing the External Boundary checkbox.

8. Report Generator
The Report Generator option in the toolbar or the Analysis menu, displays a summary of
Slide2 model and analysis information, in its own view.

Select: Analysis > Report Generator

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 20/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

The display of information in the Report Generator can be customized using the Section
Visibility checkboxes.

In the toolbar, you will see various options available for your Report including Save, Export
(as PDF), and Print.

The information can also be copied to the clipboard using the right-click Copy option
(highlight the text and select Copy). From the clipboard, the information can be pasted into a
word processing programs for your own use.

9. Drawing Tools
In the Tools menu or the toolbar, a wide variety of drawing and annotation options are
available for customizing views, including text boxes, property tables, dimensioning tools,
polylines and shapes.

It is left as an optional exercise to experiment with adding drawing tools to the view.

EDITING ANNOTATIONS AND DRAWING TOOLS

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 21/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

After drawing tools have been added to a view, they can be edited as follows.

Right-click
If you right-click the mouse on an annotation, property table, shape etc. added with the
drawing tools, you will see a popup menu, which makes available various editing and visibility
options. For example, Copy, Delete, Format.

Single-click
If you single-click the left mouse button, this will “select” the object, and you will see the
“control points” highlighted on the object. While in this mode:

You can click and drag the control points, to re-size the tool.

If you hover the mouse over any part of the drawing tool, but NOT on a control point, you
will see the four-way arrow cursor, allowing you to click and drag the entire drawing tool
to a new location.

You can delete the tool by pressing Delete on the keyboard.

Double-click
If you double-click the mouse on an object (such as a table, shape, textbox etc.), you will see
the Format Tool dialog. The Format Tool dialog allows you to customize styles, colours etc.
Only the options applicable to the clicked-on object will be enabled in the Format Tool
dialog. (Note: this is the same Format option available when you right-click).

It is left as an optional exercise, for the user to experiment with the various editing options
that are available for each Tools option.

SAVING DRAWING TOOLS

All annotations added with the drawing tools are automatically saved when you save a Slide2
file, in either the Interpret or Model programs.

10. Exporting Images

In Slide2, various options are available for exporting image files.

EXPORT IMAGE
The Export Image option in the File menu or the right-click menu, allows you to save the
current view directly to one of the following image file formats:

PNG (*.png)

JPEG (*.jpg)

GIF (*.gif)
Windows Bitmap (*.bmp)

Windows Enhanced Metafile (*.emf)

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 22/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

Windows Metafile (*.wmf)

COPY TO CLIPBOARD
The current view can also be copied to the Windows clipboard using the Copy option in the
toolbar or the Edit menu. This will place a bitmap image or enhanced metafile on the
clipboard which can be pasted directly into word or image processing applications.

We have now covered some of the basic features in the Slide2 Interpret program. Additional
features are covered in the next tutorial.

11. Multi Scenario Modeling

To conclude this tutorial, we will very briefly introduce multi-scenario modelling.

1. Return to the Slide2 Model program. (Analysis > Modeler if you are still in the Interpret
window)
2. In the Document Viewer, right-click on Group 1 – Master Scenario, and select Add
Scenario from the popup menu.

3. This will create a new scenario which is a copy of the Master Scenario.

4. Save the file

5. Select Scenario 2 in the Document Viewer.

6. Select Surfaces > Surface Options and change the Search Method = Auto Refine
Search. Select OK.

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 23/24
5/13/23, 11:43 PM Slide2 Tutorials | Quick Start Tutorial

7. Save the file.

8. Select Compute. In the compute dialog, make sure the Scenario 2 checkbox is also
selected. Select OK to run the analysis.

9. Select Interpret.

10. Select Show All Surfaces and then vertically tile the windows (Window>Tile Vertically)
You should see the following results.

11. In a few mouse clicks, you have created a new scenario, selected a different search
method for the new scenario, computed and displayed the results for two scenarios.

12. Notice that the safety factor using the Auto Refine Method is nearly identical to the Grid
Search results. For further information on Multi Scenario modelling in Slide2 see Tutorial 24.

That concludes this Quick Start Tutorial. You may now exit the program.

https://www.rocscience.com/help/slide2/tutorials/tutorials-overview/quick-start-tutorial 24/24