ENGLISH DOOR CLOSER

QDC-212 and QDC-312

Incorrect installation or adjustment could cause

Installation Instructions damage or injury. Read and follow instructions

carelfully.
with Hold-Open Arm

S e t H o l d O pe n

1. Using dimensions from the appropriate diagram above, mark four (4) holes on door for door closer and four (4) holes on frame for parallel bracket. 2.
Drill pilot holes in door and frame. Drill 7/32” (5.5mm) diameter holes for wood screws or drill and tap #7 (.201” diameter) for 1/4-20 machine screws.
3. Mount closer on door using screws provided. SPEED ADJUSTING VALVE MUST BE POSITIONED AWAY FROM HINGE SIDE. 4. Install the parallel
bracket to frame using screws provided. 5. Using a wrench on the square shaft at bottom of closer, rotate the shaft approximately 45° towards hinge
edge of door. Holding shaft in place, position main arm on pinion shaft at top, indexing main arm mark “L” or “R” with pinion flat as shown in (Figure
1). Secure main arm to pinion shaft with screw and lock washer. 6. With screws provided, attach the arm assembly to inside of bracket with hold open
nut positioned as follows: For left- hand door, hold open nut is positioned down (see Figure LH for reference). For right-hand door, hold open nut is
positioned up (see Figure RH for reference). 7. Adjust length of forearm to allow end of forearm to slide onto post of main arm. Secure together with screw
and washer. 8. Adjust closing speed and power, see page 4. 9. Snap pinion cap over shaft at bottom of closer or install (optional) cover using small screws.
The closing force for series QDC200 door closers is adjustable from a size 1 to a size 6,
as outlined in ANSI Standard A156.4. When these series of door closers are installed and By law, the Americans with Disabilities
adjusted to conform to ADA reduced opening force requirements (5 lbs max) for interior Act (ADA) may require that door closer
doors, they may not have adequate closing force to reliably close and latch door. Power installation comply with accessibility Door Closer with Hold-Open Arm
adjustments charted on this page are recommended where possible to ensure proper guidelines.
1 / 10
door control. Db: ai EO104756
ENGLISH QDC-312 Door Opening Dim A Hold Degrees

QDC300
to 100° 7-5/8 (194) 90° ~ 100°
Incorrect installation or adjustment
Option A - Regular Arm Installation could cause damage or injury. Read 101° to 130° 6-1/8 (156) 101° ~ 130°
and follow instructions carefully. 131° to 180° 4-1/8 (105) 131° ~ 180°
Hold Open
Nut UP
Centerline of
Hinge or Pivot
Diagram for Option A
6 1 - 3/ 4 7/ 8
( 152) ( 44. 4) ( 22)

1 - 1/ 4
( 32)

3/ 4
( 19)
Right-hand Door

Right-hand door shown. Reverse

dimensions for left-hand door
9 - 1/ 16
A ( 230)
application.

Option A: 1. Select degree of opening from table above and use template dimensions shown in
diagram. Mark four holes on door for door closer and two holes on frame for arm shoe. 2. Drill pilot
holes in door and frame for #14 all-purpose screws or drill and tap for 1/4-20 machine screws. 3.
Install adjustable forearm/arm shoe assembly to frame using screws provided. 4. Install main arm
to top pinion shaft using screw provided. 5. Mount door closer on door using screws provided.
SPRING POWER ADJUSTING NUT MUST BE POSITIONED AWAY FROM HINGE EDGE. 6.
Adjust length of adjustable forearm so that adjustable forearm is perpendicular to frame when
Left-hand Door assembled to preloaded main arm. Secure forearm to main arm with screw provided. 7. Snap
pinion cap over shaft at bottom of door closer (pinion cap not necessary when using full cover). 8.
Hold Open Adjust closing speed, backcheck control, and spring power of door per instructions on Sheet 4,
Nut DOWN Door Closer Adjustments.

Door Opening Dim A Hold Degrees

Option B - Top Jamb Installation

QDC300
to 100° 7-5/8 (194) 90° ~ 100°
101° to 130° 6-1/8 (156) 101° ~ 130°
131° to 180° 4-1/8 (105) 131° ~ 180°

Centerline of
Hinge or Pivot
Hold Open Diagram for Option B
Nut UP
9 - 1/ 16
A ( 230) 1 - 1/ 2
( 38)

Right-hand Door
3/ 4
1/ 2 ( 19) 6 1 - 3/ 4
( 13)
( 152) ( 44.4)
Left-hand door shown. Reverse
dimensions for left-hand door
application.
Option B: 1. Select degree of opening from table above and use template dimensions shown in
diagram. Mark four holes on door for door closer and two holes on frame for arm shoe. 2. Drill pilot
holes in door and frame for #14 all-purpose screws or drill and tap for 1/4-20 machine screws. 3.
Hold Open Install adjustable forearm/arm shoe assembly to door using screws provided. 4. Install main arm to
Nut DOWN top pinion shaft using screw provided. 5. Mount door closer body on frame using screws provided.
SPRING POWER ADJUSTING NUT MUST BE POSITIONED AWAY FROM HINGE EDGE. 6.
Adjust length of adjustable forearm so that adjustable forearm is perpendicular to door when
assembled to preloaded main arm. Secure forearm to main arm with screw provided. 7. Snap
pinion cap over shaft at top of door closer (pinion cap not necessary when using full cover). 8.
Adjust closing speed, backcheck control, and spring power of door per instructions on Sheet 4,
Left-hand Door Door Closer Adjustments.
Door Closer with Hold-Open Arm
2 / 10
ENGLISH
Dim A
QDC-212 Door Opening Hold Degrees

QDC200
Incorrect ins tallation or adjus tment to 100° 7-1/2 (191) 90° ~ 100°

Option A – R egular Arm Ins ta llation could caus e damage or injury. R ead
and follow ins tructions carefully.
101° to 130° 6 (152) 101° ~ 130°
131° to 180° 4-1/2 (114) 131° ~ 180°

Hold Open
Nut UP

Centerline of
Hinge or Pivot
Diagram for Option A

1
1 - 3 /8 5 - 1 /2 1 - 3 /4
(25.4)
(35) (140) (44.4)
3 /4
(19)

Right-hand Door 12
A (304.8)

Right-hand door shown. Reverse

dimensions for left-hand door
application.

Option A: 1. Select degree of opening from table above and use template dimensions shown in
diagram. Mark four holes on door for door closer and two holes on frame for arm shoe. 2. Drill pilot
holes in door and frame for #14 all-purpose screws or drill and tap for 1/4-20 machine screws. 3.
Install adjustable forearm/arm shoe assembly to frame using screws provided. 4. Install main arm
to top pinion shaft using screw provided. 5. Mount door closer on door using screws provided.
SPRING POWER ADJUSTING NUT MUST BE POSITIONED AWAY FROM HINGE EDGE. 6.
Adjust length of adjustable forearm so that adjustable forearm is perpendicular to frame when
assembled to preloaded main arm. Secure forearm to main arm with screw provided. 7. Snap
pinion cap over shaft at bottom of door closer (pinion cap not necessary when using full cover). 8.
Adjust closing speed, backcheck control, and spring power of door per instructions on Sheet 4,
Door Closer Adjustments.
Left-hand Door
Hold Open
Nut DOWN

Option B
Door Opening Dim A Hold Degrees
– Top J amb Ins tallation
QDC200

to 100° 7-1/2 (191) 90° ~ 100°

101° to 130° 6 (152) 101° ~ 130°
131° to 180° 4-1/2 (114) 131° ~ 180°
Centerline of
Hinge or Pivot
Diagram for Option B
12
A 1 - 7 /8
Hold Open (304.8)
(48)
Nut UP

3 /4
1 /2 (19) 5 - 1 /2 1 - 3 /4
(13)
Right-hand Door (140) (44.4)

Left-hand door shown. Reverse

dimensions for left-hand door
application.

Option B: 1. Select degree of opening from table above and use template dimensions shown in
diagram. Mark four holes on door for door closer and two holes on frame for arm shoe. 2. Drill pilot
holes in door and frame for #14 all-purpose screws or drill and tap for 1/4-20 machine screws. 3.
Install adjustable forearm/arm shoe assembly to door using screws provided. 4. Install main arm to
Hold Open top pinion shaft using screw provided. 5. Mount door closer body on frame using screws provided.
Nut DOWN SPRING POWER ADJUSTING NUT MUST BE POSITIONED AWAY FROM HINGE EDGE. 6.
Adjust length of adjustable forearm so that adjustable forearm is perpendicular to door when
assembled to preloaded main arm. Secure forearm to main arm with screw provided. 7. Snap
pinion cap over shaft at top of door closer (pinion cap not necessary when using full cover). 8.
Adjust closing speed, backcheck control, and spring power of door per instructions on Sheet 4,
Left-hand Door Door Closer Adjustments.

Door Closer with Hold-Open Arm

3 / 10
FRANÇAIS QDC-212 et QDC-312 L'ajustement ou l'installation incorrect a pu causer

Instructions d'Installation Séries Avec Tenir le Bras des dommages ou des dommages physiques. Lisez
et suivez les instructions soigneusement.
Ouvert.
Montage du bras parallèle (côté d'où l'on pousse) PORTE DE
ÉLÉMENTS
MAIN GAUCHE
Assemblage
du bras

Équerre

S e t H o l d O pe n

(Porte de main gauche) Avant-bras

VALVES
D'AJUSTEMENT DE LA Installer le
VITESSE Installer le
bras ici bras ici

Commencer
ici (clé)
Détails du montage du bras
Montage du bras parallèle (côté d'où l'on pousse) PORTE DE
MAIN DROITE
PORTE DE MAIN GAUCHE PORTE DE MAIN DROITE

Pignon à plat Pignon à plat

PORTE

Marque du bras Marque du bras

PORTE DE MAIN GAUCHE PORTE DE MAIN DROITE

(Porte de main droite)

VALVES
D'AJUSTEMENT DE LA
VITESSE ÉCROU
VERS
LE HAUT
Équerre
Équerre
Pouces (mm)
Ouverture de la porte Assemblage
du bras

ÉCROU
VERS Assemblage
LE BAS du bras

1. À l'aide des dimensions du tableau approprié ci-dessus, marquer quatre (4) emplacements sur la porte pour monter le ferme-porte et quatre (4) emplacements à l'intérieur du
cadre pour monter l'équerre de fixation parallèl. 2. Percer des trous guides dans la porte et sur le cadre, diamètre de 7/32” (5.5mm) pour le bois ou #7 (.201” diamètre) pour vis
polyvalentes ou 1/4-20 vis de métaux. 3. Monter le plus près de la porte à l'aide des vis fournies. LES VALVES D'AJUSTEMENT DE LA VITESSE DOIVENT ÊTRE PLACÉES LOIN
DES CHARNIÈRES. 4. Installer l'équerre de fixation parallèle à l'aide des vis fournies. 5. À l'aide d'une clé pour tenir la tige carrée à la base du ferme-porte, faire pivoter la tige
pour la placer à environ 45° vers les charnières de la porte. En retenant la tige en place, placer le bras principal sur le pignon de la tige, réunir le bras principal « L » ou « R » avec
le pignon à plat comme sur la figure 1. Fixer le bras principal au pignon à l'aide de la vis et de la rondelle de blocage. 6. Attacher le mécanisme du bras à l'intérieur de l'équerre
parallèle, à l'aide des vis fournies, en gardant l'écrou pour garder la porte ouverte vers le bas (voir Figure LH). Pour une porte ouvrant par la droite, l'écrou pour garder la porte
ouverte doit être placé vers le haut (voir la Figure RH). 7. Ajuster la tige de l'avant-bras pour permettre à son bout de glisser sur le poteau du bras principal. Fixer avec les vis et les
rondelles. 8. Ajuster la vitesse et la puissance de fermeture de la porte, consulter la page 4 pour voir comment faire. 9. Enclencher le couvercle du pignon sur l'axe à la base du
pignon du ferme-porte ou installer (optionnel) le couvercle avec les petites vis fournies.
La force de fermeture des ferme-portes de la série QDC300 peut être ajustée aux dimensions 1 à 4, tel qu'il est En vertu de la loi, l'Americans with Disabilities Act (ADA) (loi sur les
stipulé dans la norme ANSI A156.4. Lorsque des ferme-portes de cette série sont installés et ajustés de façon à Américains ayant une incapacité), on peut avoir à respecter les lignes
être conformes aux exigences de force d'ouverture réduite de l'ADA (5 lb max.) pour les portes intérieures, la force
directrices d'accessibilité.
de fermeture ne sera peut être pas suffisante fermer et verrouiller la porte correctement. Les ajustements de Door Closer with Hold-Open Arm
puissance indiqués sur le tableau sont recommandés là où ils s'appliquent afin d'obtenir un contrôle de la porte
adéquat. 4 / 10
 Door Opening Dim A Hold Degrees
FRANÇAIS QDC312

QDC300
L'ajustement ou l'installation incorrect a pu causer to 100° 7-5/8 (194) 90° ~ 100°
des dommages ou des dommages physiques. Lisez
101° to 130° 101° ~ 130°
Option A - Regular Arm Installation et suivez les instructions soigneusement.
6-1/8 (156)
131° ~ 180°
131° to 180° 4-1/8 (105)
Hold Open
Nut UP Ligne Centrale pour la
Charnière ou le Pivot

Diagram for Option A

6 1 - 3/ 4 7/ 8
( 152) ( 44. 4) ( 22)

1 - 1/ 4
( 32)

R 3/ 4
RE
TI ( 19)
Porte Main Droite

Right-hand door shown. Reverse

dimensions for left-hand door
9 - 1/ 16
A ( 230)
application.

Option A: 1. Select degree of opening from table above and use template dimensions shown in
diagram. Mark four holes on door for door closer and two holes on frame for arm shoe. 2. Drill pilot
holes in door and frame for #14 all-purpose screws or drill and tap for 1/4-20 machine screws. 3.
Install adjustable forearm/arm shoe assembly to frame using screws provided. 4. Install main arm
to top pinion shaft using screw provided. 5. Mount door closer on door using screws provided.
TI
RE SPRING POWER ADJUSTING NUT MUST BE POSITIONED AWAY FROM HINGE EDGE. 6.
R Adjust length of adjustable forearm so that adjustable forearm is perpendicular to frame when
assembled to preloaded main arm. Secure forearm to main arm with screw provided. 7. Snap
Porte Main Gauche pinion cap over shaft at bottom of door closer (pinion cap not necessary when using full cover). 8.
Hold Open Adjust closing speed, backcheck control, and spring power of door per instructions on Sheet 4,
Nut DOWN Door Closer Adjustments.

Door Opening Dim A Hold Degrees

Option B - Top Jamb Installation

QDC300
to 100° 7-5/8 (194) 90° ~ 100°
101° to 130° 6-1/8 (156) 101° ~ 130°
131° to 180° 4-1/8 (105) 131° ~ 180°

Ligne Centrale pour la

Charnière ou le Pivot
PO
US Diagram for Option B
SE
R
Hold Open 9 - 1/ 16
A 1 - 1/ 2
Nut UP ( 230)
( 38)

3/ 4
Porte Main Droite 1/ 2 ( 19) 6 1 - 3/ 4
( 13)
( 152) ( 44.4)
Left-hand door shown. Reverse
dimensions for right-hand door
application.

Option B: 1. Select degree of opening from table above and use template dimensions shown in
diagram. Mark four holes on door for door closer and two holes on frame for arm shoe. 2. Drill pilot
holes in door and frame for #14 all-purpose screws or drill and tap for 1/4-20 machine screws. 3.
ER Install adjustable forearm/arm shoe assembly to door using screws provided. 4. Install main arm to
USS
PO top pinion shaft using screw provided. 5. Mount door closer body on frame using screws provided.
Hold Open
SPRING POWER ADJUSTING NUT MUST BE POSITIONED AWAY FROM HINGE EDGE. 6.
Nut DOWN Adjust length of adjustable forearm so that adjustable forearm is perpendicular to door when
assembled to preloaded main arm. Secure forearm to main arm with screw provided. 7. Snap
pinion cap over shaft at top of door closer (pinion cap not necessary when using full cover). 8.
Adjust closing speed, backcheck control, and spring power of door per instructions on Sheet 4,
Door Closer Adjustments.
Porte Main Gauche
Door Closer with Hold-Open Arm
5 / 10
 Dim A
QDC-212 Door Opening Hold Degrees
FRANÇAIS

QDC200
Incorrect ins tallation or adjus tment to 100° 7-1/2 (191) 90° ~ 100°

Option A - Regular Arm Installation could caus e damage or injury. R ead

and follow ins tructions carefully.
101° to 130° 6 (152) 101° ~ 130°
131° to 180° 4-1/2 (114) 131° ~ 180°

Hold Open
Nut UP

Ligne Centrale pour la

Charnière ou le Pivot
Diagram for Option A
1
1 - 3 /8 5 - 1 /2 1 - 3 /4
(25.4)
(35) (140) (44.4)
3 /4
(19)

Porte Main Droite

12
A (304.8)

Right-hand door shown. Reverse

dimensions for left-hand door
application.

Option A: 1. Select degree of opening from table above and use template dimensions shown in
diagram. Mark four holes on door for door closer and two holes on frame for arm shoe. 2. Drill pilot
holes in door and frame for #14 all-purpose screws or drill and tap for 1/4-20 machine screws. 3.
Install adjustable forearm/arm shoe assembly to frame using screws provided. 4. Install main arm
to top pinion shaft using screw provided. 5. Mount door closer on door using screws provided.
SPRING POWER ADJUSTING NUT MUST BE POSITIONED AWAY FROM HINGE EDGE. 6.
Adjust length of adjustable forearm so that adjustable forearm is perpendicular to frame when
assembled to preloaded main arm. Secure forearm to main arm with screw provided. 7. Snap
pinion cap over shaft at bottom of door closer (pinion cap not necessary when using full cover). 8.
Porte Main Gauche Adjust closing speed, backcheck control, and spring power of door per instructions on Sheet 4,
Door Closer Adjustments.
Hold Open
Nut DOWN

Door Opening Dim A Hold Degrees

Option B - Top Jamb Installation
QDC200

to 100° 7-1/2 (191) 90° ~ 100°

101° to 130° 6 (152) 101° ~ 130°
131° to 180° 4-1/2 (114) 131° ~ 180°
Ligne Centrale pour la
Charnière ou le Pivot
Diagram for Option B
12
Hold Open A (304.8) 1 - 7 /8
(48)
Nut UP

3 /4
1 /2 (19) 5 - 1 /2
Porte Main Droite (13)
(140)
1 - 3 /4
(44.4)
Left-hand door shown. Reverse
dimensions for right-hand door
application.

Option B: 1. Select degree of opening from table above and use template dimensions shown in
diagram. Mark four holes on door for door closer and two holes on frame for arm shoe. 2. Drill pilot
holes in door and frame for #14 all-purpose screws or drill and tap for 1/4-20 machine screws. 3.
Install adjustable forearm/arm shoe assembly to door using screws provided. 4. Install main arm to
Hold Open top pinion shaft using screw provided. 5. Mount door closer body on frame using screws provided.
Nut DOWN SPRING POWER ADJUSTING NUT MUST BE POSITIONED AWAY FROM HINGE EDGE. 6.
Adjust length of adjustable forearm so that adjustable forearm is perpendicular to door when
assembled to preloaded main arm. Secure forearm to main arm with screw provided. 7. Snap
pinion cap over shaft at top of door closer (pinion cap not necessary when using full cover). 8.
Adjust closing speed, backcheck control, and spring power of door per instructions on Sheet 4,
Porte Main Gauche Door Closer Adjustments.

Door Closer with Hold-Open Arm

6 / 10
ESPAÑOL Serie QDC-212 y QDC-312 La incorrecta instalación o el ajuste
con brazo para mantener incorrecta podría causar daño o lesión. Lea
Instrucciones de Instalación la puerta abierta.
y siga las instrucciones cuidadosamente.

Montaje de brazo paralelo (lado de empujar). PUERTA DE

COMPONENTES
MANO IZQUIERDA
Ensamblaje del
Brazo

PUERTA
Soporte

S e t H o l d O pe n

(Puerta de mano izquierda) Antebrazo

Figura 1

VÁLVULAS
DE AJUSTE DE
VELOCIDAD Instale el
Instale el
brazo aquí. brazo aquí.
Empiece
(llave)
Montaje de brazo paralelo (lado de empujar). aquí. Detalle del Montaje del Brazo
PUERTA DE
MANO DERECHA
PUERTA DE MANO IZQUIERDA PUERTA DE MANO DERECHA

Placa de Piñón Placa de Piñón

PUERTA

Marca del Brazo Marca del Brazo

PUERTA DE MANO IZQUIERDA PUERTA DE MANO DERECHA

(Puerta de mano derecha)

Figura LH Figura RH

VÁLVULAS
DE AJUSTE DE
VELOCIDAD
Soporte
Soporte TUERCA
ARRIBA
Pulgadas (mm)
Apertura de la Puerta Ensamblaje
del
Brazo

Ensamblaje
TUERCA del Brazo
ABAJO

1. Utilizando las dimensiones del diagrama anterior apropiado, marque cuatro (4) lugares en la puerta para montar el cerrador de la puerta y cuatro (4) lugares en la parte
interior del marco para montar el soporte paralelo. 2. Taladre agujeros piloto en la puerta y en el marco, 7/32” (5.5mm) diámetro para madera, o #7 (.201” diámetro) para los
tornillos de uso múltiple o 1/4-20 tornillos de la máquina. 3. Monte el cerrador en la puerta utilizando los tornillos provistos. LAS VÁLVULAS DE AJUSTE DE VELOCIDAD DEBE
SER COLOCADO LEJOS DE LAS BISAGRAS. 4. Instale el Soporte Paralelo en el marco utilizando los tornillos provistos. 5. Utilizando una llave en el eje cuadrado que hay
en la parte inferior del cerrador, haga girar el eje aproximadamente 45º hacia el borde de bisagra de la puerta. Manteniendo el eje en su lugar, coloque el brazo principal
en el eje de piñón de la parte superior, alineando la marca “L” o “R” del brazo principal con la placa de piñón según se indica en la (Figura 1). Afiance el brazo principal
al eje de piñón con un tornillo y una arandela de fijación. 6. Con los tornillos provistos, una el ensamblaje del brazo a la parte interior del soporte paralelo con la tuerca del
dispositivo que se utiliza para mantener la puerta abierta colocada como sigue: Para la puerta de orientación izquierda, la tuerca del dispositivo que se utiliza para mantener
la puerta abierta se coloca hacia abajo (vea la Figura LH como referencia). Para la puerta de orientación derecha, la tuerca que se utiliza para mantener la puerta abierta
se coloca hacia arriba (vea la Figura RH como referencia). 7. Ajuste la longitud del antebrazo de manera que permita que el extremo del antebrazo se deslice por encima
del poste del brazo principal. Afiáncelos con un tornillo y una arandela. 8. Ajuste la velocidad y la fuerza de cierre de la puerta, vea la página 4 como referencia. 9. Ajuste
la tapa del piñón por encima del eje en la parte inferior del cerrador o instale la cubierta (electiva) con los tornillos pequeños.
La fuerza de cierre de los cierres automáticos de puerta de la serie QDC300 es ajustable, del tamaño 1 al tamaño 4, La Ley de Estadounidenses con Discapacidades (Americans with
como se describe en la norma A156.4 de ANSI. Cuando estas series de cierres automáticos de puerta se instalan y Disabilities Act o ADA) puede exigir que la instalación del cierre
ajustan para cumplir con los requisitos de fuerza de abertura reducida de ADA (máximo de 5 libras) para las puertas automático de puerta sea acorde con las pautas de accesibilidad.
interiores, pueden no tener suficiente fuerza de cierre para cerrar y trabar con seguridad la puerta. Cuando sea
posible, se recomienda efectuar los ajustes de la fuerza incluidos en el gráfico de esta página para asegurar
Door Closer with Hold-Open Arm
suficiente control de la puerta. 7 / 10
ESPAÑOL QDC312 Door Opening Dim A Hold Degrees

QDC300
La incorrecta instalación o el ajuste to 100° 7-5/8 (194) 90° ~ 100°
incorrecta podría causar daño o lesión. Lea
y siga las instrucciones cuidadosamente. 101° to 130° 6-1/8 (156) 101° ~ 130°

Opción A - Instalación Normal 131° to 180° 4-1/8 (105) 131° ~ 180°

Hold Open
Nut UP
Línea Central de la
Bisagra o del Pivote
Diagrama para Opción A
6 1 - 3/ 4 7/ 8
( 152) ( 44. 4) ( 22)

1 - 1/ 4
( 32)

3/ 4
RE
TI ( 19)
Puerta para Mano Derecha

Right-hand door shown. Reverse

9 - 1/ 16 dimensions for left-hand door
A ( 230) application.

Opción A: 1. Select degree of opening from table above and use template dimensions shown in
diagram. Mark four holes on door for door closer and two holes on frame for arm shoe. 2. Drill pilot
holes in door and frame for #14 all-purpose screws or drill and tap for 1/4-20 machine screws. 3.
Install adjustable forearm/arm shoe assembly to frame using screws provided. 4. Install main arm
to top pinion shaft using screw provided. 5. Mount door closer on door using screws provided.
TI SPRING POWER ADJUSTING NUT MUST BE POSITIONED AWAY FROM HINGE EDGE. 6.
RE
Adjust length of adjustable forearm so that adjustable forearm is perpendicular to frame when
Puerta para assembled to preloaded main arm. Secure forearm to main arm with screw provided. 7. Snap
pinion cap over shaft at bottom of door closer (pinion cap not necessary when using full cover). 8.
Hold Open Mano Izquierda Adjust closing speed, backcheck control, and spring power of door per instructions on Sheet 4,
Nut DOWN Door Closer Adjustments.
Door Opening Dim A Hold Degrees
Opción B - Top Jamb Installation

QDC300
to 100° 7-5/8 (194) 90° ~ 100°
101° to 130° 6-1/8 (156) 101° ~ 130°
131° to 180° 4-1/8 (105) 131° ~ 180°

PR
Línea Central de la
ES
IO
Bisagra o del Pivote
NE
Diagrama para Opción B
Hold Open
Nut UP 9 - 1/ 16
A ( 230) 1 - 1/ 2
( 38)

Puerta para Mano Derecha 3/ 4

1/ 2 ( 19) 6 1 - 3/ 4
( 13)
( 152) ( 44.4)
Left-hand door shown. Reverse
dimensions for left-hand door
application.

Opción B: 1. Select degree of opening from table above and use template dimensions shown in
diagram. Mark four holes on door for door closer and two holes on frame for arm shoe. 2. Drill pilot
NE holes in door and frame for #14 all-purpose screws or drill and tap for 1/4-20 machine screws. 3.
SIO
PRE Install adjustable forearm/arm shoe assembly to door using screws provided. 4. Install main arm to
Hold Open
top pinion shaft using screw provided. 5. Mount door closer body on frame using screws provided.
Nut DOWN SPRING POWER ADJUSTING NUT MUST BE POSITIONED AWAY FROM HINGE EDGE. 6.
Adjust length of adjustable forearm so that adjustable forearm is perpendicular to door when
assembled to preloaded main arm. Secure forearm to main arm with screw provided. 7. Snap
pinion cap over shaft at top of door closer (pinion cap not necessary when using full cover). 8.
Puerta para Adjust closing speed, backcheck control, and spring power of door per instructions on Sheet 4,
Door Closer Adjustments.
Mano Izquierda Door Closer with Hold-Open Arm
8 / 10
ESPAÑOL
Dim A
QDC-212 Door Opening Hold Degrees

QDC200
Incorrect ins tallation or adjus tment to 100° 7-1/2 (191) 90° ~ 100°

Option A – R egular Arm Ins ta llation could caus e damage or injury. R ead
and follow ins tructions carefully.
101° to 130° 6 (152) 101° ~ 130°
131° to 180° 4-1/2 (114) 131° ~ 180°

Hold Open
Nut UP Línea Central de la
Bisagra o del Pivote

Diagram for Option A

1
1 - 3 /8 5 - 1 /2 1 - 3 /4
(25.4)
(35) (140) (44.4)
3 /4
(19)

12
A (304.8)

Puerta para Mano Derecha

Right-hand door shown. Reverse
dimensions for left-hand door
application.

Opción A: 1. Select degree of opening from table above and use template dimensions shown in
diagram. Mark four holes on door for door closer and two holes on frame for arm shoe. 2. Drill pilot
holes in door and frame for #14 all-purpose screws or drill and tap for 1/4-20 machine screws. 3.
Install adjustable forearm/arm shoe assembly to frame using screws provided. 4. Install main arm
to top pinion shaft using screw provided. 5. Mount door closer on door using screws provided.
SPRING POWER ADJUSTING NUT MUST BE POSITIONED AWAY FROM HINGE EDGE. 6.
Adjust length of adjustable forearm so that adjustable forearm is perpendicular to frame when
assembled to preloaded main arm. Secure forearm to main arm with screw provided. 7. Snap
pinion cap over shaft at bottom of door closer (pinion cap not necessary when using full cover). 8.
Puerta para Adjust closing speed, backcheck control, and spring power of door per instructions on Sheet 4,
Door Closer Adjustments.
Hold Open Mano Izquierda
Nut DOWN

Option B
Door Opening Dim A Hold Degrees
– Top J amb Ins tallation
QDC200

to 100° 7-1/2 (191) 90° ~ 100°

101° to 130° 6 (152) 101° ~ 130°
131° to 180° 4-1/2 (114) 131° ~ 180°
Línea Central de la
Bisagra o del Pivote
Diagram for Option B
12
A (304.8) 1 - 7 /8
Hold Open (48)

Nut UP

3 /4
1 /2 (19) 5 - 1 /2 1 - 3 /4
(13)
(140) (44.4)
Puerta para Mano Derecha Left-hand door shown. Reverse
dimensions for left-hand door
application.

Opción B: 1. Select degree of opening from table above and use template dimensions shown in
diagram. Mark four holes on door for door closer and two holes on frame for arm shoe. 2. Drill pilot
holes in door and frame for #14 all-purpose screws or drill and tap for 1/4-20 machine screws. 3.
Hold Open Install adjustable forearm/arm shoe assembly to door using screws provided. 4. Install main arm to
Nut DOWN top pinion shaft using screw provided. 5. Mount door closer body on frame using screws provided.
SPRING POWER ADJUSTING NUT MUST BE POSITIONED AWAY FROM HINGE EDGE. 6.
Adjust length of adjustable forearm so that adjustable forearm is perpendicular to door when
assembled to preloaded main arm. Secure forearm to main arm with screw provided. 7. Snap
pinion cap over shaft at top of door closer (pinion cap not necessary when using full cover). 8.
Puerta para Adjust closing speed, backcheck control, and spring power of door per instructions on Sheet 4,
Mano Izquierda Door Closer Adjustments.
Door Closer with Hold-Open Arm
 9 / 10
 1-855-365-
2407 1-
855-365-
2407
1-855-365-2407
www.
stanl
eysecur
it
ysol
uti
ons.
com www.st
anl
eysecur
it
ysol
uti
ons.
com www.st
anleysecuri
tysol
uti
ons.
com