Technical Data

JOTACOTE 5

Product description
Jotacote 5 is a two-pack, water borne inorganic zinc rich silicate primer. Can be applied in high
film thickness.

Recommended use
As protection on blast cleaned steel. Can be used alone and also overcoated with water borne
coatings, as well as with suitable solvent borne coatings, such as epoxy and others. Not to be
overcoated with alkyds. Jotacote 5 can also be used as a one coat system for interior tanks. A
separate resistance list is available.

Film thickness and spreading rate

Minimum Maximum Typical Typical for
immersion
services:
Film thickness, dry (µm) 50 200 75 125
Film thickness, wet (µm) 75 300 110 190
Theoretical spreading rate 13,4 3,4 8,9 5,4
(m²/l)
Comments
VOC: 0 g/l (Actual).
There is a risk of mud cracking if the dry film thickness exceeds 250 µm

Physical properties
Colour Grey
Solids (vol %)* 67 ± 2
Flash point Non flammable
Gloss Flat
Water resistance Very good
Abrasion resistance Excellent
Solvent resistance Excellent
Chemical resistance Excellent within pH range of 6-10
Flexibility Limited
*Measured according to ISO 3233:1998 (E)

Surface preparation
All surfaces should be clean, dry and free from contamination. The surface should be assessed
and treated in accordance with ISO 8504.

Bare steel
Cleanliness: Blast cleaning to Sa 2½ (ISO 8501-1:1988).Roughness: using abrasives suitable to
achieve grade Fine to Medium G (30-85 µm, Ry5) (ISO 8503-2)

Other surfaces
The coating may be used on other substrates. Please contact your local Jotun office for more
information.

JOTACOTE 5 Page 1
Condition during application
The temperature of the substrate should be minimum 5°C and at least 3°C above the dew point
of the air, temperature and relative humidity measured in the vicinity of the substrate. Good
ventilation is usually required in confined areas to ensure proper drying. Use mistcoat technique
for subsequent coat to avoid popping (pinholes). If possible avoid application at relative humidity
below (30%) due to risk of dry spraying.

Application methods
Spray Conventional spray. (for example, Wiwa high pressure pump
R/F/W-G-34020).
Brush Recommended for stripe coating and small areas, care must be taken to
achieve the specified dry film thickness.

Application data
Mixing ratio (volume) 25 kg Comp. B (Zinc powder) to be sifted slowly into 7 kg Comp. A
(Silicate solution) and mixed thoroughly. It is recommended to pass
the mixture through a 60 mesh sieve before use.
Pot life (23°C) 5 hours.
Thinner/Cleaner Fresh water.
Guiding data airless spray
Nozzle tip 1.8 - 2.2 mm (0.71” - 0.87”)
Note With Jotacote 5 it is recommended to flush the system with Jotun
thinner No. 4 and then circulate water through the spraying
equipment for some minutes before application. After the paintwork
is finished, flush the system with water. During painting it is
necessary to continuously stir the paint with a mechanical stirrer.

Drying time
Drying times are generally related to air circulation, temperature, film thickness and number of
coats, and will be affected correspondingly. The figures given in the table are typical with:
* Good ventilation (Outdoor exposure or free circulation of air)
* Typical film thickness
* One coat on top of inert substrate
* Relative humidity < = 70%

Substrate temperature 10°C 23°C 40°C

Surface dry 20 min 15 min 10 min
Through dry 40 min 30 min 20 min
Cured 20 d 10 d 5d
Dry to recoat, minimum 24 h 8h 5h

The given data must be considered as guidelines only. The actual drying time/times before
recoating may be shorter or longer, depending on film thickness, ventilation, humidity, underlying
paint system, requirement for early handling and mechanical strength etc. A complete system
can be described on a system sheet, where all parameters and special conditions could be
included.

JOTACOTE 5 Page 2
Typical paint system
Jotacote 5 1 x 75 µm (Dry Film Thickness)
WaterFine Special 1 x 60 µm (Dry Film Thickness)
WaterFine Special 1 x 60 µm (Dry Film Thickness)
WaterFine Topcoat 1 x 50 µm (Dry Film Thickness)

FOR INTERIOR OF TANKS OR SINGLE COAT SYSTEM:

Jotacote 5 1 x 125 µm (Dry Film Thickness)

Other systems may be specified, depending on area of use

Complete curing:
When the Jotacote 5 is used as a one coat system for the interior of tanks the paint must be
completely cured before the tank is put into service. In order to achieve this the following
procedures can be used:

l Apply 125 µm Jotacote 5.

l Let the paint dry/cure with good ventilation and low humidity until minimum recoating time is
reached.
l Spray water (seawater is preferred) on the coating and leave the tank closed. Repeat the
water spraying 3 - 4 times during a 48 hours period.
l Remove the water and let the tank dry.

Procedure for preparation and cleaning of application

equipment:
To avoid solvent contamination of the water borne paint the spraying equipment has to be
conditioned before use. All equipment containing solvents in the pump, hoses and gun have to
be thoroughly cleaned according to the following instructions.

If the application equipment is made in stainless steel, designed for and only used for application
of water borne coatings this preparation and cleaning procedure is not needed.

Before spraying:
Circulate Jotun Thinner No. 17 through the equipment and hoses. Then Jotun Thinner No. 4
before fresh clean water.

After spraying:
Clean the equipment and hoses with water and detergent (Kraftvask), then circulate Jotun
Thinner No. 4 and finally Jotun Thinner No. 17.

Storage
The component A must be stored above 0°C and in accordance with national regulations, subject
to re-inspection thereafter. Storage conditions are to keep the containers in a dry, cool, well
ventilated space and away from source of heat and ignition. The product component B is zinc dust
and has no strict limitation's for storage. Containers must be kept tightly closed.

JOTACOTE 5 Page 3
Handling
Handle with care. Stir well before use.Continuous stirring during application will prevent the
heavy zinc pigment from settling. SHELF LIFE: 9 months at 23°C for Comp. A, 4 years for comp.
B Higher temperatures during storage may reduce the shelf life and may lead to gelling in the
tin.

Packing size
7 kg Comp. A , 25 kg Comp. B (Together 9.7 l paint)
Packing may vary from country to country according to local requirements.

Health and safety

Please observe the precautionary notices displayed on the container. Use under well ventilated
conditions. Do not breathe or inhale mist. Avoid skin contact. Spillage on the skin should
immediately be removed with suitable cleanser, soap and water. Eyes should be well flushed with
water and medical attention sought immediately.

For detailed information on the health and safety hazards and precautions for use of
this product, we refer to the Material Safety Data Sheet.

DISCLAIMER
The information in this data sheet is given to the best of our knowledge based on laboratory
testing and practical experience. However, as the product is often used under conditions beyond
our control, we cannot guarantee anything but the quality of the product itself. We reserve the
right to change the given data without notice.

Head Office & Nordic Europe Middle East South East Asia
Jotun Paints Jotun Paints (Europe) Ltd. Jotun U.A.E Ltd. LLC. Jotun (Singapore) Pte. Ltd.
P.O. Box 2021 Stather Road, Flixborough Al Quoz Industrial Area No 11-15, Sixth Lok Yang Road
N-3248 Sandefjord North Lincolnshire DN15 8RR P.O Box 3671 Jurong
Norway United Kingdom Dubai U.A.E Singapore 628 111
Phone +47 33 45 70 00 Phone +44 172 44 00 000 Phone +971 4 3 39 50 00 Phone +65 6265 4711
Fax +47 33 46 46 13 Fax +44 172 44 00 100 Fax +971 4 3 38 06 66 Fax +65 6265 7484

Jotun is a World Wide company with factories, sales offices and stocks in more than 50 countries. For your
nearest local Jotun address please contact the nearest regional office or visit our website at www.jotun.com

ISSUED 13 FEBRUARY 2002 BY JOTUN PAINTS

THIS DATA SHEET SUPERSEDES THOSE PREVIOUSLY ISSUED

PDF Version :

JOTACOTE 5 Page 4