Jotafloor Sealer is a transparent two-pack epoxy sealer that provides good adhesion between flooring products and concrete surfaces. It can be used as a sealer or primer before applying other Jotafloor products, or on its own to bind dust on concrete floors. The sealer dries to a glossy finish and offers very good water resistance, flexibility, and chemical resistance. It is applied using spray, brush, or roller in one or two 40 micron coats and can be overcoated once dry.
Jotafloor Sealer is a transparent two-pack epoxy sealer that provides good adhesion between flooring products and concrete surfaces. It can be used as a sealer or primer before applying other Jotafloor products, or on its own to bind dust on concrete floors. The sealer dries to a glossy finish and offers very good water resistance, flexibility, and chemical resistance. It is applied using spray, brush, or roller in one or two 40 micron coats and can be overcoated once dry.
Jotafloor Sealer is a transparent two-pack epoxy sealer that provides good adhesion between flooring products and concrete surfaces. It can be used as a sealer or primer before applying other Jotafloor products, or on its own to bind dust on concrete floors. The sealer dries to a glossy finish and offers very good water resistance, flexibility, and chemical resistance. It is applied using spray, brush, or roller in one or two 40 micron coats and can be overcoated once dry.
Jotafloor Sealer is a transparent two-pack epoxy sealer that provides good adhesion between flooring products and concrete surfaces. It can be used as a sealer or primer before applying other Jotafloor products, or on its own to bind dust on concrete floors. The sealer dries to a glossy finish and offers very good water resistance, flexibility, and chemical resistance. It is applied using spray, brush, or roller in one or two 40 micron coats and can be overcoated once dry.
Product description Jotafloor Sealer is a transparent two-pack epoxy sealer/primer exhibiting excellent penetration properties to ensure good adhesion between Jotafloor products and most masonry surfaces.
Recommended use As a sealer/primer for subsequent Jotafloor products or for use independently as a dustbinder for concrete floors.
Film thickness and spreading rate
Minimum Maximum Typical Film thickness, dry (µm) 30 50 40 Film thickness, wet (µm) 80 130 100 Theoretical spreading rate (m²/l) 12.5 7.7 10 Comments Substrate porosity and profile will affect practical coverage rates.
Physical properties Colour Transparent Solids (vol %)* 40 ± 2 Flash point 25ºC ± 2 (Setaflash) Gloss Glossy Water resistance Very good Solvent resistance Excellent Chemical resistance Excellent Check chemical resistance values in Jotafloor chemical resistance chart. Flexibility Good
*Measured according to ISO 3233:1998 (E)
Surface preparation All concrete damaged by exposure to chemicals, contaminated by any substance or unsound in any way, shall be removed to expose sound concrete.
Coated surfaces Clean, dry and undamaged compatible primer. Contact your local Jotun office for more information.
Other surfaces Concrete surface preparation by using dust free captive blasting units, grinding equipment, sand blasting or high pressure water jetting is critical to achieving the right surface profile prior to paint application. Contact your local Jotun office for more information.
The coating may be used on other substrates. Please contact your local Jotun office for more information.
JOTAFLOOR SEALER Page 1
Condition during application The temperature of the substrate should be minimum 10°C and at least 3°C above the dew point of the air, temperature and relative humidity measured in the vicinity of the substrate. Good ventilation is usually required in confined areas to ensure proper drying. The moisture content in the concrete should not exceed 4 % (by weight). The coating should not be exposed to oil, chemicals or mechanical stress until fully cured.
Application methods Spray Use airless spray or conventional spray Brush Recommended for stripe coating and small areas, care must be taken to achieve the specified dry film thickness. Roller May be used. However when using roller application care must be taken to apply sufficient material in order to achieve the specified dry film thickness.
Application data Mixing ratio (volume) 4 parts Comp. A (base) to be mixed thoroughly with 1 part Comp. B (curing agent). NO PART MIXING Mixing ½ hour prior to use. Pot life (23°C) 8 hours (reduced at higher temp.) Thinner/Cleaner Jotun Thinner No. 17 Guiding data airless spray Pressure at nozzle 15 MPa (150 kp/cm² 2100 psi) Nozzle tip 0.46 - 0.58 mm (0.018-0.023") Spray angle 40-80° Filter Check to ensure that filters are clean
Drying time Drying times are generally related to air circulation, temperature, film thickness and number of coats, and will be affected correspondingly. The figures given in the table are typical with: * Good ventilation (Outdoor exposure or free circulation of air) * Typical film thickness * One coat on top of inert substrate
Substrate temperature 10°C 23°C 40°C
Surface dry 2h 1h 0.5 h Through dry 14 h 6,5 h 3h Cured 14 d 7d 2d Dry to recoat, minimum 8h 4h 1,5 h 1 The surface should be free from chalking and contamination prior to application. Best intercoat adhesion occurs when the subsequent coat is applied before the preceding coat has cured.
The given data must be considered as guidelines only. The actual drying time/times before recoating may be shorter or longer, depending on film thickness, ventilation, humidity, underlying paint system, requirement for early handling and mechanical strength etc. A complete system can be described on a system sheet, where all parameters and special conditions could be included.
JOTAFLOOR SEALER Page 2
Typical paint system As dust binder: Jotafloor Sealer Nominal
For coloured finish:
Jotafloor Sealer 1 x 40 µm (Dry Film Thickness) Jotafloor Topcoat 2 x 50 µm (Dry Film Thickness) or Jotafloor Sealer 1-2 x 40 µm (Dry Film Thickness) Jotafloor Coating 1 x 300 µm (Dry Film Thickness) or Jotafloor Sealer 1-2 x 40 µm (Dry Film Thickness) Jotafloor SL Universal 1 x 2000-4000 µm (Dry Film Thickness)
Note: Thickness of the finished system will vary depending on use of the finished floor. Consult your local Jotun Office for advice.
Other systems may be specified, depending on area of use
Storage The product must be stored in accordance with national regulations. Storage conditions are to keep the containers in a dry, cool, well ventilated space and away from source of heat and ignition.Containers must be kept tightly closed.
Handling Handle with care. Stir well before use.
Packing size 16 l Comp. A (base) and 4 l Comp. B (curing agent) 4 l Comp. A (base) and 1 l Comp. B (curing agent) Packing may vary from country to country according to local requirements.
Health and safety
Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do not breathe or inhale mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.
For detailed information on the health and safety hazards and precautions for use of this product, we refer to the Material Safety Data Sheet.
JOTAFLOOR SEALER Page 3
DISCLAIMER The information in this data sheet is given to the best of our knowledge based on laboratory testing and practical experience. However, as the product is often used under conditions beyond our control, we cannot guarantee anything but the quality of the product itself. We reserve the right to change the given data without notice.
Jotun is a World Wide company with factories, sales offices and stocks in more than 50 countries. For your nearest local Jotun address please contact the nearest regional office or visit our website at www.jotun.com
ISSUED 20 AUGUST 2002 BY JOTUN PAINTS
THIS DATA SHEET SUPERSEDES THOSE PREVIOUSLY ISSUED
