E1 Qsig Siemens 417588si
E1 Qsig Siemens 417588si
E1 Qsig Siemens 417588si
Table of Contents
Introduction .............................................................................................................................................................................................................. 1
Network Topology.................................................................................................................................................................................................... 2
Limitations................................................................................................................................................................................................................ 2
System Components ................................................................................................................................................................................................. 2
Hardware Requirements ...................................................................................................................................................................................... 2
Software Requirements ....................................................................................................................................................................................... 3
Features .................................................................................................................................................................................................................... 3
Features Supported .............................................................................................................................................................................................. 3
Features Not Supported ....................................................................................................................................................................................... 3
Configuration............................................................................................................................................................................................................ 3
Configuring the Siemens HiPath 4000 PBX........................................................................................................................................................ 3
Configuring the Cisco Unified CallManager..................................................................................................................................................... 16
Configuring the Cisco CMM-E1 MGCP Router ............................................................................................................................................... 31
Acronyms ............................................................................................................................................................................................................... 35
Introduction
• This is an application note for connectivity of Siemens HiPath 4000 Release 1 PBX with Cisco Unified CallManager (CUCM) Release
4.1 using Cisco Communication Media Module CMM-E1 PRI as MGCP gateway.
• The network topology diagram (Figure 1) shows the test setup for end-to-end interoperability with the Cisco Unified CallManager
connected to the PBX via CMM-E1 PRI link as MGCP gateway.
• Connectivity is achieved by using the PRI EURO protocol type on the MGCP gateway and ETSI switch type on the Siemens HiPath
4000 PBX.
• This Application Note uses the CMM-E1 voice gateway, however other Cisco voice gateways are also an option to use since Cisco
Unified CallManager ISDN PRI implementation does not depend on the physical interface.
Cisco
Cisco Unified
Catalyst
PBX1: Siemens HiPath CallManager
6000
4000 Release 1 Release 4.1
Ethernet
Switch
ISDN Type:
1-3-25-1
Phone A
x5002 1-2-79-1 E1-PRI NET5
PBX #1 CMM-E1
Dial-4XXX
Phone B ISDN Type:
x5003 E1-PRI NET5
Cisco 7960 IP phones
Phone C Phone D
x4000 x4001
PSTN
Dial Plans
To PBX Ext. 5XXX
Phone F Dial To PSTN 91650-XXXXXXX
1650-364-6325 91408-527-XXXX
Limitations
• The Siemens HiPath 4000 PRI Interface with ETSI protocol does not support Calling Name Delivery Presentation feature.
• Cisco Unified CallManager 4.1 PRI implementation does not support sending Connected Number information.
B-Channel Mapping
• Siemens HiPath 4000 PBX uses Timeslot channel numbering (1-15, 17-31) when ETSI protocol is selected, therefore the Cisco CMM-
E1 Gateway configuration for Channel IE Type field should be set to Timeslot Number.
System Components
Hardware Requirements
• Cisco Hardware:
• Cisco Catalyst 6000 switch with CMM-E1 Gateway
Features
Features Supported
• CLIP-Calling Line (Number) Identification Presentation
Features Not Supported
• Calling/Connected Name delivery is not supported by the Siemens HiPath 4000 PRI Interface with ETSI protocol
• Sending Connected Number is not supported by Cisco CallManager 4.1 PRI protocol
Configuration
DPLN
<dis-wabe:gen;
DIS-WABE:GEN;
H500: AMO WABE STARTED
------------------------------------------------------------------------------
| DIGIT INTERPRETATION VALID FOR ALL DIAL PLANS |
------------------------------------------------------------------------------
| | CALL PROGRESS STATE | DIGIT | RESERVED/CONVERT |
| CODE | 1 11111 11112 22| ANALYSIS | DNI/ADD-INFO |
| |0 12345 67890 12345 67890 12| RESULT | *=OWN NODE |
------------------------------------------------------------------------------
| 0 |. .**** ..*** **... ..... .*| CO | R |
| 001 - 009 |* ..... ..... ..... ..... ..| NETRTE | |
| 111 |. .**** ***** **... ..... .*| TIE | |
| 12 |. .**** ***** **... ..... .*| TIE | R |
| 13 - 14 |. .**** ***** **... ..... .*| TIE | |
| 21 |. ..... ..... ..... ....* ..| KNOVRKY | |
| 22 |. ..... ..... ..... ....* ..| DNDKY | |
| 222 |. .**** ***** **... ..... .*| TIE | |
| 23 |. ..... ..... ..... ....* ..| FWDKY | |
| 24 |. ..... ..... ..... ....* ..| MBKY | |
| 25 |. ..... ..... ..... ....* ..| MSGRKY | |
| 26 |. ..... ..... ..... ....* ..| DAKY | |
| 27 |. ..... ..... ..... ....* ..| DSSKY | |
<DISPLAY-LDPLN:TYPE=LDP,LDPNO=4;
DISPLAY-LDPLN:TYPE=LDP,LDPNO=4;
H500: AMO LDPLN STARTED
+--------------+-------------------------------------------------+
| | |
| LDPNO : 4 | LDP : 111-X |
| | SPC : 22 |
| | FDSFIELD : 0 SDSFIELD : 0 PINDP : N |
+------+-------+-------------------------------------------------+
| DPLN | LROUTE| LAUTH |
|------+-------+-------------------------------------------------+
| 0 | 1 | 1 |
| 1 | 1 | 1 |
| 2 | 1 | 1 |
| 3 | 1 | 1 |
| 4 | 1 | 1 |
| 5 | 1 | 1 |
<DISPLAY-LDPLN:TYPE=LDP,LDPNO=12;
DISPLAY-LDPLN:TYPE=LDP,LDPNO=12;
H500: AMO LDPLN STARTED
+--------------+-------------------------------------------------+
| | |
| LDPNO : 12 | LDP : 59-X |
| | SPC : 22 |
| | FDSFIELD : 0 SDSFIELD : 0 PINDP : N |
+------+-------+-------------------------------------------------+
| DPLN | LROUTE| LAUTH |
|------+-------+-------------------------------------------------+
| 0 | 27 | 1 |
| 1 | 27 | 1 |
| 2 | 27 | 1 |
| 3 | 27 | 1 |
| 4 | 27 | 1 |
| 5 | 27 | 1 |
| 6 | 27 | 1 |
| 7 | 27 | 1 |
| 8 | 27 | 1 |
| 9 | 27 | 1 |
| 10 | 27 | 1 |
| 11 | 27 | 1 |
| 12 | 27 | 1 |
| 13 | 27 | 1 |
| 14 | 27 | 1 |
| 15 | 27 | 1 |
+------+-------+-------------------------------------------------+
<DISPLAY-LDPLN:TYPE=LDP,LDPNO=5;
DISPLAY-LDPLN:TYPE=LDP,LDPNO=5;
H500: AMO LDPLN STARTED
+--------------+-------------------------------------------------+
| | |
| LDPNO : 5 | LDP : 9-1650-XXXXXXX |
| | SPC : 22 |
| | FDSFIELD : 0 SDSFIELD : 0 PINDP : N |
+------+-------+-------------------------------------------------+
| DPLN | LROUTE| LAUTH |
|------+-------+-------------------------------------------------+
| 0 | 165 | 1 |
| 1 | 165 | 1 |
| 2 | 165 | 1 |
BCSU
PRI Board
<DISPLAY-BCSU:TYPE=TBL,LTG=1,LTU=3,SLOT=25;
DISPLAY-BCSU:TYPE=TBL,LTG=1,LTU=3,SLOT=25;
H500: AMO BCSU STARTED
PSTN board
<DISPLAY-BCSU:TYPE=TBL,LTG=1,LTU=2,SLOT=79;
DISPLAY-BCSU:TYPE=TBL,LTG=1,LTU=2,SLOT=79;
H500: AMO BCSU STARTED
<dis-cot:22;
DIS-COT:22;
H500: AMO COT STARTED
COT: 22 INFO:
DEVICE: INDEP SOURCE: DB
PARAMETER:
PRIORITY FOR AC WILL BE DETERMINED FROM MESSAGE PRI
RECALL IF USER HANGS UP IN CONSULTATION CALL RCL
<DISPLAY-COP:COPNO=21;
DISPLAY-COP:COPNO=21;
H500: AMO COP STARTED
COP: 21 INFO:
DEVICE: INDEP SOURCE: DB
PARAMETER:
LINE WITH END-OF-DIAL EOD
SPECIAL MODE SFRM
CODE CALLING RELEASE AFTER EVERY TASK CCR
REGISTRATION OF LAYER 3 ADVISORIES L3AR
CO TRUNK ACCESS:
TRUNK ACCESS TA
TOLL ACCESS:
TRUNK ACCESS TA
<DISPLAY-COSSU:TYPE=COS,COS=32;
DISPLAY-COSSU:TYPE=COS,COS=32;
H500: AMO COSSU STARTED
+------+-----------------+---------------+-----------------+
| COS | VOICE | FAX | DTE |
+------+-----------------+---------------+-----------------+
| 32 |> |
| | TA | NOCO | TA |
| | TNOTCR | NOTIE | TNOTCR |
| | | | BASIC |
| | | | MSN |
| | | | CDRINT |
| | | | MULTRA |
| | | | |
+------+-----------------+---------------+-----------------+
AMO-COSSU-111 CLASSES OF SERVICE
DISPLAY COMPLETED;
<DISPLAY-COSSU:TYPE=LCOSV,LCOSV=1;
DISPLAY-COSSU:TYPE=LCOSV,LCOSV=1;
H500: AMO COSSU STARTED
<DISPLAY-BUEND:TGRP=27,FORMAT=L;
DISPLAY-BUEND:TGRP=27,FORMAT=L;
H500: AMO BUEND STARTED
<dis-tdcsu:1-3-25-1;
DIS-TDCSU:1-3-25-1;
H500: AMO TDCSU STARTED
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2CONN PEN = 1-03-025-1 TGRP = 27 |
|---------------------------------------------------------------------------|
| PROTVAR = ETSI INS = Y SRCHMODE = CIR |
| COTNO = 22 COPNO = 21 DPLN = 0 |
| ITR = 1 COS = 32 LCOSV = 1 |
| LCOSD = 1 CCT = PRI ECMA 4 DESTNO = 111 |
| SEGMENT = 1 DEDSCC = DEDSVC = NONE |
| FACILITY = DITIDX = SRTIDX = |
<DISPLAY-LWPAR:FORMAT=L,BLNO=1,TYPE=DIUS2;
DISPLAY-LWPAR:FORMAT=L,BLNO=1,TYPE=DIUS2;
H500: AMO LWPAR STARTED
+-----------------------------------------------------------------------+
| LOADWARE PARAMETERS CIRCUIT TYPE: DIUS2 SOURCE:DB BLOCK: 1 |
+-----------------------------------------------------------------------+
| LNTYPE = COPPER VERSION = S2 QUAL = ON |
| MASTER = Y DCHAN1 = 16 DCHAN2 = 0 |
| PATTERN = D5H QUAL1 = 10 SEC. QUAL2 = 10 MIN. |
| SMD = Y PERMACT = Y FCBAB = DFH |
| CDG = N FIXEDTEI = 0 CNTRNR = 255 |
| TEIVERIF = N CRC4REP = N |
| DEV = INDEP |
| INFO = |
+-----------------------------------------------------------------------+
<dis-tdcsu:1-3-25-1;
DIS-TDCSU:1-3-25-1;
H500: AMO TDCSU STARTED
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2CONN PEN = 1-03-025-1 TGRP = 27 |
|---------------------------------------------------------------------------|
| PROTVAR = ETSI INS = Y SRCHMODE = CIR |
| COTNO = 22 COPNO = 21 DPLN = 0 |
| ITR = 1 COS = 32 LCOSV = 1 |
| LCOSD = 1 CCT = PRI ECMA 4 DESTNO = 111 |
| SEGMENT = 1 DEDSCC = DEDSVC = NONE |
| FACILITY = DITIDX = SRTIDX = |
| TRTBL = GDTR SIDANI = N ATNTYP = TIE |
| CBMATTR = NONE NWMUXTIM = 10 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNIP = ISDNNP = |
| PNPL2P = PNPL1P = PNPAC = |
<DISPLAY-LWPAR:FORMAT=L,BLNO=0,TYPE=DIUS2;
DISPLAY-LWPAR:FORMAT=L,BLNO=0,TYPE=DIUS2;
H500: AMO LWPAR STARTED
+-----------------------------------------------------------------------+
| LOADWARE PARAMETERS CIRCUIT TYPE: DIUS2 SOURCE:DB BLOCK: 0 |
+-----------------------------------------------------------------------+
| LNTYPE = COPPER VERSION = S2 QUAL = ON |
| MASTER = N DCHAN1 = 16 DCHAN2 = 0 |
| PATTERN = D5H QUAL1 = 10 SEC. QUAL2 = 10 MIN. |
| SMD = N PERMACT = Y FCBAB = DFH |
| CDG = N FIXEDTEI = 0 CNTRNR = 255 |
| TEIVERIF = N CRC4REP = N |
| DEV = INDEP |
| INFO = |
+-----------------------------------------------------------------------+
<dis-tdcsu:1-2-79-1;
DIS-TDCSU:1-2-79-1;
H500: AMO TDCSU STARTED
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2CONN PEN = 1-02-079-1 TGRP = 23 |
|---------------------------------------------------------------------------|
| PROTVAR = ETSI INS = Y SRCHMODE = CIR |
| COTNO = 21 COPNO = 21 DPLN = 0 |
| ITR = 1 COS = 10 LCOSV = 32 |
| LCOSD = 32 CCT = PRI ECMA 2 DESTNO = 100 |
| SEGMENT = 8 DEDSCC = DEDSVC = NONE |
| FACILITY = DITIDX = SRTIDX = |
| TRTBL = GDTR SIDANI = N ATNTYP = TIE |
| CBMATTR = NONE NWMUXTIM = 10 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNIP = ISDNNP = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 1 |
| ALARMNO = 0 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 21 FWDX = 10 |
| DOMTYPE = DOMAINNO = TPROFNO = |
<DISPLAY-REFTA:TYPE=CIRCUIT,PEN=1-3-25-1,KIND=ALL;
DISPLAY-REFTA:TYPE=CIRCUIT,PEN=1-3-25-1,KIND=ALL;
H500: AMO REFTA STARTED
+-------------------------------------------------------------------------+
| R E F E R E N C E C L O C K C I R C U I T S |
+--------------+---------+----------+---+------+------+------+-----+------+
| PEN | MODULE | DEVICE |PRI|ERROR |BLOCK |SUPP. |READY|SRCGRP|
| | | | | | | |BUT | |
| | | | | | | |ASYN.| |
+--------------+---------+----------+---+------+------+------+-----+------+
| 1- 3- 25- 1 | DIU-N2 | S2CONN | 0| 0| N | | N | 1|
+--------------+---------+----------+---+------+------+------+-----+------+
<DISPLAY-REFTA:TYPE=CIRCUIT,PEN=1-3-25-1,KIND=ALL;
DISPLAY-REFTA:TYPE=CIRCUIT,PEN=1-3-25-1,KIND=ALL;
H500: AMO REFTA STARTED
+-------------------------------------------------------------------------+
| R E F E R E N C E C L O C K C I R C U I T S |
+--------------+---------+----------+---+------+------+------+-----+------+
| PEN | MODULE | DEVICE |PRI|ERROR |BLOCK |SUPP. |READY|SRCGRP|
| | | | | | | |BUT | |
| | | | | | | |ASYN.| |
+--------------+---------+----------+---+------+------+------+-----+------+
| 1- 3- 25- 1 | DIU-N2 | S2CONN | 11| 0| N | | N | 1|
+--------------+---------+----------+---+------+------+------+-----+------+
LDAT
<DISPLAY-LDAT:TYPE=LCR,LROUTE=27;
DISPLAY-LDAT:TYPE=LCR,LROUTE=27;
H500: AMO LDAT STARTED
+--------------------------------------------------------------------------+
| LROUTE = 27 LDPLN NAME = PRI 4 ECMA1 SERVICE = ALL |
| TYPE = LCR DNNO OF ROUTE = 111 |
| SERVICE INFO = |
+-------+-----+-----+-----+------+----------+------------+----------+------+
| | | | | | SCHEDULE | CARRIER | | |
| LRTEL | LVAL| TGRP| ODR| LAUTH| ABCDEFGH | ZONE | LATTR | LDSRT|
+-------+-----+-----+-----+------+----------+------------+----------+------+
| 1 | 1| 27| 15| 1 | ******** | 1 EMPTY | NONE | |
+-------+-----+-----+-----+------+----------+------------+----------+------+
RICHT
DISPLAY-RICHT:MODE=LRTE,LRTE=1;
H500: AMO RICHT STARTED
+-----------------------------------------------------------------+
| LRTE = 1 NAME = ROPTCCM (NEUTRAL) LSVC = ALL |
| DNNO = 111 PDNNO = 0 DESTNO =111 |
| ROUTOPT = YES REROUT = YES PLB = NO FWDBL = NO |
| DTMFCNV = WITHOUT DTMFDSP = WITHOUT DTMFTEXT = |
| DTMFPULS = BUGS = LIN ROUTATT = NO MAINGRP = 24 |
| EMCYRTT = NO CONFTONE = NO RERINGRP = NO RTENO = 24 |
<DISPLAY-RICHT:MODE=LRTE,LRTE=27;
DISPLAY-RICHT:MODE=LRTE,LRTE=27;
H500: AMO RICHT STARTED
+-----------------------------------------------------------------+
| LRTE = 27 NAME = PRI 4 ECMA1 (NEUTRAL) LSVC = ALL |
| DNNO = 111 PDNNO = 0 |
| ROUTOPT = YES REROUT = YES PLB = NO FWDBL = NO |
| DTMFCNV = FIX DTMFDSP = WITHOUT DTMFTEXT = |
| DTMFPULS = PP300 BUGS = LIN ROUTATT = NO MAINGRP = 15 |
| EMCYRTT = NO CONFTONE = NO RERINGRP = NO RTENO = 15 |
| INFO = |
| NOPRCFWD = NO |
+-----------------------------------------------------------------+
| TGRP = 27 LDAT PRI ECMA 4 (NEUTRAL) SUBGROUP = 10 |
+-----------------------------------------------------------------+
PSTN RICHT
<DISPLAY-RICHT:MODE=LRTE,LRTE=165;
DISPLAY-RICHT:MODE=LRTE,LRTE=165;
H500: AMO RICHT STARTED
+-----------------------------------------------------------------+
| LRTE = 165 NAME = PSTN 91650 (NEUTRAL) LSVC = ALL |
| DNNO = 89 PDNNO = 0 DESTNO = 89 |
| ROUTOPT = YES REROUT = YES PLB = NO FWDBL = NO |
| DTMFCNV = WITHOUT DTMFDSP = WITHOUT DTMFTEXT = |
| DTMFPULS = BUGS = LIN ROUTATT = NO MAINGRP = 27 |
| EMCYRTT = NO CONFTONE = NO RERINGRP = NO RTENO = 27 |
| INFO = |
| NOPRCFWD = NO |
+-----------------------------------------------------------------+
| TGRP = 23 LDAT ECMA 2 (NEUTRAL) SUBGROUP = 6 |
+-----------------------------------------------------------------+
<DISPLAY-LODR:ODR=111,FORMAT=L;
H500: AMO LODR STARTED
+-------------------------------------------------------+
| ODR POSITION CMD PARAMETER |
+--------+----------------------------------------------+
| 111 | 1 ECHO 1 |
| | 2 ECHO 2 |
| | 3 END |
+--------+----------------------------------------------+
H03: THE NEXT FREE ODR IS 2
<DISPLAY-PERSI:TYPE=NAME,STNO=5002;
DISPLAY-PERSI:TYPE=NAME,STNO=5002;
H500: AMO PERSI STARTED
+--------+-----------------------------------------+---------------------------+
| STNO | CHRISTIAN AND SURNAME CHARCON | ORGANIZATIONAL UNIT |
+--------+-----------------------------------------+---------------------------+
| | | |
| 5002 | HIPATH DT2* | |
| | | |
+--------+-----------------------------------------+---------------------------+
cisco WS-SVC-CMM Cat6k Voice Linecard (R7000) processor (revision 0xFF) with 196
608K/65536K bytes of memory.
R7000 CPU at 400Mhz, Implementation 39, Rev 3.3, 256KB L2 Cache
Last reset from power-on
Bridging software.
Primary Rate ISDN software, Version 1.1.
Channelized E1, Version 1.0.
1 FastEthernet/IEEE 802.3 interface(s)
1 Gigabit Ethernet/IEEE 802.3 interface(s)
186 Serial network interface(s)
6 Channelized E1/PRI port(s)
32768K bytes of processor board bootflash (Read/Write)
CMM-E1#
CMM-E1#sh run
Building configuration...
CMM-E1#
Acronym Definitions
AOC Advice-of-charge. Information element is sent with the connection setup information for
incoming Euro-ISDN connections. The AOC IE is used for call charge calculation.
CUCM Cisco Unified CallManager
CLIP Calling Line (Number) Identification Presentation
CMM Communication Media Module (CMM) is a Cisco Catalyst® 6500 Series and Cisco 7600
Series line card that provides flexible and high-density T1/E1 gateways
PSTN Public Switched Telephone Network
WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO
BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR
INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA
ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN
Argentina • Australia • Austria • Belgium • Brazil • Bulgaria • Canada • Chile • China PRC • Colombia • Costa Rica • Croatia • Czech
Republic • Denmark • Dubai, UAE • Finland • France • Germany • Greece • Hong Kong SAR • Hungary • India • Indonesia • Ireland •
Israel • Italy • Japan • Korea • Luxembourg • Malaysia • Mexico • The Netherlands • New Zealand • Norway • Peru • Philippines •
Poland • Portugal • Puerto Rico • Romania • Russia • Saudi Arabia • Scotland • Singapore • Slovakia • Slovenia • South Africa • Spain •
Sweden • Switzerland • Taiwan • Thailand • Turkey Ukraine • United Kingdom • United States • Venezuela • Vietnam • Zimbabwe
© 2007 Cisco Systems, Inc. All rights reserved.
CCVP, the Cisco logo, and Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of
Cisco Systems, Inc.; and Access Registrar, Aironet, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified Internetwork Expert logo,
Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step,
Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, iQuick Study,
LightStream, Linksys, MeetingPlace, MGX, Networkers, Networking Academy, Network Registrar, PIX, ProConnect, ScriptShare, SMARTnet, StackWise, The Fastest Way
to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship
between Cisco and any other company. (0711R)