Data Sheet

Cisco E1/T1 ISDN PRI Network Modules for Cisco 2610-51XM, 2800, 2691, 3660, 3700 and 3800 Series Routers
The versatility of Cisco 2610-51XM, 2800, 2691, 3660, 3700 and 3800 series routers is demonstrated by their broad support of E1/T1 connectivity and Integrated Services Digital Network Primary Rate Interfaces (ISDN PRI). Customers continue to deploy E1 and T1 circuits for Wide Area Network (WAN) connectivity, ISDN dial-backup, and digital modem termination in the Power Branch Office Environment. Cisco now makes it possible to terminate T1 and E1 PRI connections in a single network module. Available in single and dual port models, the NM-1CE1T1-PRI and NM-2CE1T1-PRI cards coupled with Cisco 2610-51XM, 2800, 2691, 3660, 3700 and 3800 Series routers, enhance and simplify customers WAN connectivity options (Figure 1).

Figure 1. Single-Port E1/T1 ISDN PRI Network Module (NM-1CE1T1-PRI)

The Cisco E1/T1 ISDN PRI Network Modules integrated channel service unit (CSU) provides direct connection to the Telecommunications network, thus allowing customers to consolidate customer premises equipment (CPE). This provides multifunction dial access aggregation, routing functionality, VPN and firewall security, and other capabilities right inside the Cisco router in power branch office environments. Both the 1-port and 2-port versions offer support for balanced and unbalanced E1 connectivity and conform easily to customers specific applications. The Cisco E1/T1 ISDN PRI network modules also supply connectivity for internal digital modems in the Cisco 3660, 3700 and 3800 series routers, with connectivity options for PRI, T1 channel associated signaling (T1-CAS), and E1-CAS R2 signaling. This provides for a high concentration of V.92-compatible modems, while still allowing expandability for other critical services. FEATURES AT-A-GLANCE Cisco IOS Software configurable for T1 or E1 operation Balanced or unbalanced E1 termination in the same module Integrated CSU/DSU (channel service unit/data service unit) per port Full or fractional E1/T1can be fully channelized Supports PRI for data, T1-CAS, and E1-CAS R2 signaling E1 unframed and framed modes (G.703/G.704) available Interoperates with NM-xDM digital modem network modules Bantam (tty) jacks for easy network monitoring V.54 loopback compatible

All contents are Copyright 19922005 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement. Page 1 of 1

 Supported on Cisco 2610-51XM, 2800, 2691, 3660, 3700 and 3800 Series routers Online insertion and removal (OIR) supported on Cisco 3660 3745 and 3845 routers On-board expansion slot for future technologies KEY BENEFITS Enhanced Flexibility The Cisco E1/T1 ISDN PRI network modules (NM-xCE1T1-PRI) are software configurable between E1 or T1 operation, balanced or unbalanced E1 termination, and CSU/DSU. Customers no longer need to buy a specific module for T1 support and then another card for E1 connectivity. In addition, the same modules provide for balanced (120-ohm) and unbalanced (75-ohm) E1 termination. See table 5 for available cable adaptors. Support for G.703 Unstructured E1 Signaling International Telecommunications Union (ITU) signaling standard G.703 was previously available only on Cisco midrange routers through the VWIC-xFT-G703 Voice/WAN interface card, which did not support data PRI. Framed E1 (G.704) is also supported for international customers without G.703 service. High-Density PRI Connectivity Options For midrange, high-density ISDN PRI applications, the Cisco 2610-51XM, 2800, 2691, 3660, 3700 and 3800 Series provide superior performance and port density. For example, a fully configured Cisco 3745 system can be configured for up to eight ISDN PRI connections in one chassis. These ports can be fully channelized to provide up to 192 T1 channels at 56/64 Kbps each, or 240 E1 channels at 56/64 Kbps each. Increased Manageability and Troubleshooting Critical loopback support makes the 1-port and 2-port Cisco E1/T1 ISDN PRI network modules easy to manage. Both models have the capability to internally loop back the on-board framer chip towards the interface, thus eliminating the need for an external loopback plug. Local, remote, line, and payload loopbacks, along with support for V.54 inline loop commands complement the Cisco E1/T1 ISDN PRI Network Modules management features. Integrated bantam (tty) jacks allow line monitoring equipment to be inserted for circuit troubleshooting. The single set of jacks can be software selected to monitor port-0 or port-1 without interrupting service. Blue, yellow, and red alarm detection, as well as a new command to disable yellow alarm detection and generation, gives customers better control over their WAN connections. This feature, combined with support for the Cisco WAN Access Performance Management System (WAPMS), Cisco Intelligence Engine 2100, and CiscoWorks makes troubleshooting easy when necessary Reliability Integrating the external E1/T1 terminating device (CSU/DSU) increases the overall system reliability. Possible points of failure are reduced by eliminating the second power supply, additional fans, extra cabling, and other equipment that accompany a two-box solution. This increase in reliability allows Service Providers to more easily and cost effectively meet the requirements of their customers Service Level Agreements (SLAs) and provides enterprises with maximum equipment uptime.

2005 Cisco Systems, Inc. All rights reserved. Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com. Page 2 of 8

PLATFORM SUPPORT Supported Platforms and Minimum Software and Memory Requirements Memory requirements depend on the selected platform, software feature set, and other installed modules and features. The Cisco E1/T1 ISDN PRI network modules are supported in the Cisco 2610-51XM, 2800, 2691, 3660, 3700, and 3800 routers. For information about memory planning, refer to the software release notes, the Cisco IOS Software Upgrade Planner, or ask your local Cisco representative. Table 1 below shows the minimum Cisco IOS Software requirements for each platform. Table 1.
Platform Cisco 2610-51 (Non-XM Models) Cisco 2610-51XM Cisco 2800 Series Cisco 2691 Cisco 3620, 3640, 3640A Cisco 3660 Cisco 3700 Series Cisco 3800 Series

Supported Platforms and Minimum Software Requirements

Minimum Cisco IOS Software Release Not supported Cisco IOS Software Release 12.3 and 12.3T Cisco IOS Software Release 12.3(08)T Cisco IOS Software Release 12.3 and 12.3T Not supported Cisco IOS Software Release 12.3 and 12.3T Cisco IOS Software Release 12.3 and 12.3T Cisco IOS Software Release 12.3(11)T

Maximum Cisco NM-xCE1T1-PRI Network Modules per Platform Table 2 shows the maximum Cisco E1/T1 ISDN Network Module supported in each platform. Table 2. Maximum Supported NM-xCE1T1-PRI Modules per Platform
Cisco 261051XM 1 1 Cisco 2800 1 1 Cisco 2691 1 1 Cisco 3660 6 6 Cisco 3725 2 2 Cisco 3745 4 4 Cisco 3825 2 2 Cisco 3845 4 4

Type of Module NM-1CE1T1-PRI NM-2CE1T1-PRI

SOFTWARE AND MANAGEMENT FEATURES Table 3 shows the software and management features for the Cisco E1/T1 ISDN PRI Network Modules. Table 3.
Feature Diagnostic Loopback Support

Software and Management Features

Description E1 loopback modes

Controller local loopback Interface local loopback

T1 loopback modes

Interface local loopback Interface remote loopback

2005 Cisco Systems, Inc. All rights reserved. Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com. Page 3 of 8

Feature

Description

Controller local loopback Controller remote loopback

CSU loopback modes for T1 CSU

Data terminal equipment (DTE) loopback Network loopback Payload loopback V.54
Alarm Detection

Yellow AlarmReceive/Send from/to network Blue AlarmReceive alarm indication signal (AIS) from network Red AlarmLoss of network signal

Relevant Management Information Base (MIB) Support Remote Management

RFC1406-MIB CISCO-ICSUDSU-MIB Supported by Cisco WAN Access Performance Management System (WAPMS) Cisco Intelligence Engine (IE2100) CiscoWorks

Signaling Debugging

CAS debugs ISDN Q.921 and Q.931 decode All other previously existing applicable Cisco IOS debugs

HARDWARE SPECIFICATIONS Table 4 shows the hardware specifications for the Cisco E1/T1 ISDN PRI Network Module. Table 4.
Feature Dimensions (H x W x D)

Hardware Specifications for the Cisco E1/T1 ISDN PRI Network Module
Description

1.55 x 7.10 x 7.2 inches 3.9 x 18.0 x 18.3 centimeters

Operating Temperature Nonoperating Temperature Relative Humidity LEDs

32 to 104 F (0 to 40 C) 40 to 185 F (40 to 85 C) 5-95% non-condensing LEDs per port

T1: T1 mode selected E1-BAL: E1 balanced mode selected E1-UNBAL: E1 unbalanced mode selected CD: Carrier detect LP: Loop condition present RA: Remote alarm detected LA: Local alarm detected

2005 Cisco Systems, Inc. All rights reserved. Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com. Page 4 of 8

Feature

Description LEDs per module

C0: Tx/Rx Mon bantam jacks connected to port 0 C1: Tx/Rx Mon bantam jacks connected to port 1 EN: Network-module (NM) Enable AIM: Integrated Advanced Integration Module (AIM) slot in use (future usecurrently disabled)
Ports

1 or 2 E1/T1 ports on RJ-48C connectors Tx/Rx Mon bantam (tty) jacks for monitoring network activity (port selectable through Cisco IOS
Command Line Interface (CLI))

Line Bit Rate (Per Port)

E1: (2.048 Mbps) T1: (1.544 Mbps)

Line Coding

E1: HDB3 T1: AMI, B8ZS

Framing Formats

E1: CRC4 T1: SF and ESF

Output Levels

E1: short-haul/long-haul T1 (LBO): - 0, -7.5, or -15 dB

PRODUCT NUMBERS AND ORDERING INFORMATION Table 5 lists the product numbers of the Cisco E1/T1 ISDN PRI Network Module. Table 5. Product Numbers of the Cisco E1/T1 ISDN PRI Network Module
Description 1-Port Channelized E1/T1/ISDN-PRI Network Module 2-Port Channelized E1/T1/ISDN-PRI Network Module E1 Cable RJ-45 to Dual BNC (Unbalanced) E1 Cable RJ-45 to Twinax (Balanced)

Product Number NM-1CE1T1-PRI NM-2CE1T1-PRI CAB-E1-RJ45BNC CAB-E1-RJ45TWIN

REGULATORY COMPLIANCE, SAFETY, EMISSIONS, AND EMC/IMMUNITY Table 6 shows a partial listing of regulatory compliance and safety data. Table 6.
Feature Regulatory Compliance

Regulatory Compliance and Safety (Partial Listing*)

Description

FCC Part 68, TIA-968-A CS-03 Australia (S016, S038) JATE (T1) TBR4, 12, 13 (and NET5, ETS300156, ETS300 011)

2005 Cisco Systems, Inc. All rights reserved. Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com. Page 5 of 8

Feature Telecommunication Interface Industry Standards

Description

CCITT/ITU G.703, G.704, G.706, I.431, G.823 ANSI T1.403

Safety

US (UL60950) Canada (C22.2 No.60950) Europe (EN60950) Australia/New Zealand (AS/NZS3260, TS001) Other Countries (IEC60950)

NEBS EMC Emissions/Immunity

GR-63, GR-78, GR-1089-CORE Type 1/3

EN 300 386 v1.3.1:2001 AS/NZS3548:1995 VCCI:V-3/2000.04 CNS13438:1997 CFR47 Part 15:2000 EN61000-6-1:2001 CISPR22:1997 [EN55022:1998] EN55024:1998 EN50082-1:1992, EN50082-1:1997 EN61000-4-2:1995 [incl AMD1 + AMD2] EN61000-4-3:1996 [Incl AMD 1 & 2] EN61000-4-4:1995, EN61000-4-5:1995 EN61000-4-6:1996 [incl AMD1]

For more information, visit the Cisco Compliance home page (listed later in this document under Country Support) or consult your local Cisco representative for further details.

POWER AND ENVIRONMENTAL REQUIREMENTS The Cisco NM-xCE1T1-PRI network modules, when installed in Cisco routers, do not change the power or environmental requirements and standards of the router itself. See platform-specific data sheets for more information: For information about Cisco 2610-51XM and 2691 routers, visit: http://www.cisco.com/en/US/prod/collateral/routers/ps259/product_data_sheet0900aecd800fa5be.html For information about Cisco 2800 routers, visit: http://www.cisco.com/en/US/products/ps5854/index.html For information about Cisco 3660 routers, visit: http://www.cisco.com/en/US/products/hw/routers/ps274/products_data_sheet09186a0080091ba4.html For information about Cisco 3700 Series routers, visit: http://www.cisco.com/en/US/prod/collateral/routers/ps282/product_data_sheet09186a008009203f.html For information about Cisco 3800 Series routers, visit: http://www.cisco.com/en/US/products/ps5855/index.html COUNTRY SUPPORT See the following URL or contact your local Cisco representative for country-specific approval status (Cisco.com login required): http://www.cisco.com/cgi-bin/compliance/approvals_search.pl

2005 Cisco Systems, Inc. All rights reserved. Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com. Page 6 of 8

Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100

European Headquarters Cisco Systems International BV Haarlerbergpark Haarlerbergweg 13-19 1101 CH Amsterdam The Netherlands www-europe.cisco.com Tel: 31 0 20 357 1000 Fax: 31 0 20 357 1100

Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA www.cisco.com Tel: 408 526-7660 Fax: 408 527-0883

Asia Pacific Headquarters Cisco Systems, Inc. 168 Robinson Road #28-01 Capital Tower Singapore 068912 www.cisco.com Tel: +65 6317 7777 Fax: +65 6317 7799

Cisco Systems has more than 200 offices in the following countries and regions. Addresses, phone numbers, and fax numbers are listed on the Cisco Website at www.cisco.com/go/offices. Argentina Australia Austria Belgium Brazil Bulgaria Canada Chile China PRC Colombia Costa Rica Croatia Cyprus Czech Republic Denmark Dubai, UAE Finland France Germany Greece Hong Kong SAR Hungary India Indonesia Ireland Israel Italy Japan Korea Luxembourg Malaysia Mexico The Netherlands New Zealand Norway Peru Philippines Poland Portugal Puerto Rico Romania Russia Saudi Arabia Scotland Singapore Slovakia Slovenia South Africa Spain Sweden Switzerland Taiwan Thailand Turkey Ukraine United Kingdom United States Venezuela Vietnam Zimbabwe
Copyright 2005 Cisco Systems, Inc. All rights reserved. CCSP, CCVP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, PostRouting, Pre-Routing, ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet, StrataView Plus, TeleRouter, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are property of Systems, their respective owners. The use of the word partner does not imply a partnership relationship between the 2005 Cisco Inc. All rights reserved. Cisco and any other company. (0502R) notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com. 205481.Z_ETMG_CC_11.05 Important Printed in the USA

Page 7 of 8

 2005 Cisco Systems, Inc. All rights reserved. Important notices, privacy statements, and trademarks of Cisco Systems, Inc. can be found on cisco.com. Page 8 of 8