FRR500 Cab/Chassis specification as at July 2000.

MODEL RATINGS AND DIMENSIONS

MODELS ENGINE RATINGS(kg) TARE MASS#(kg) DIMENSIONS (mm) TURNING
CIRCLE
GVM GCM TOTAL FRONT REAR WB OAL ROH CA CE CH FFH FFH RFH RFH KERB
UNLADEN LADEN UNLADEN LADEN TO KERB
FRR500: SHORT 2,980 1,975 1,005 3,780 6,570 1,605 2,985 4,590 2,550 800 770 875 810 12.2m
14,890
MEDIUM 3,010 2,000 1,010 2,545 800 770 875 810
- AUTO SITEC 175 13,600 3,045 1,995 1,050 4,250 7,220 1,785 3,455 5,240 2,535 790 760 865 800 13.4m
10,400
- PTO 16,000 3,085 2,025 1,060 2,535 790 760 865 800
LONG 3,090 2,040 1,050 2,545 795 765 910 845
14,890 4,850 8,170 2,135 4,055 6,190 14.9m
FRR 500S SiTEC 200 3,120 2,070 1,050 2,545 795 765 910 845
# Estimated mass of cab/chassis with oil, water and fuel tank containing 10 litres of fuel and excluding spare wheel (47 kg) and tools (30 kg).
250

560 795 CA
CE

FFH RFH
CH

1790 1660
2200 2160 1185 WB ROH
OAL
For further information regarding Cab/Chassis dimensions your Isuzu Dealer can access detailed Body Builders diagrams from the Isuzu Truck Data Manual.

DRIVELINE SPECIFICATIONS
FUEL SYSTEM PTO (Flywheel Power Take Off)
ENGINE: ISUZU SITEC 175 • In line plunger, Bosch ‘AD’ type fuel injection pump
Isuzu 6HH1-N 6 cylinder, overhead camshaft, four (Optional specification only available on
with mechanical all speed governor. In line filter, Medium/4,250mm wheelbase)
stroke, direct injection, diesel. see through water separator with drain cock.
BORE X STROKE: 115 mm x 132 mm. • Drive ratio (PTO/Engine RPM): 0.7:1
DISPLACEMENT: 8,226 cc. • Single fuel tank, capacity 180 litres.
• Maximum output torque: 353Nm
COMPRESSION RATIO: 18.5 : 1. • Output flange rotates in same direction as engine.
POWER: 129 kW @ 2,800 RPM. (ISO 1585) CLUTCH
TORQUE: 490 Nm @ 1,700RPM. (ISO 1585) • Hydraulic control dry single plate.
355 mm (14”) diameter.
FRONT AXLE
ENGINE: ISUZU SITEC 200 • Asbestos free lining material. Total lining area ISUZU FO36 CAPACITY 3,600KG
(Optional engine only available on FRR 500S LONG) (both sides) 966 cm2. • Reverse Elliot I-beam type. King Pin diameter
Isuzu 6HH1-S 6 cylinder, overhead camshaft, four 35 mm with cylindrical roller thrust bearing.
stroke, direct injection, diesel. TRANSMISSIONS
BORE X STROKE: 115 mm x 132 mm.
ISUZU MBJ6T 6 speed overdrive
REAR AXLE
DISPLACEMENT: 8,226 cc. ISUZU RO77 CAPACITY 7,700KG
COMPRESSION RATIO: 18.5 : 1. • Constant mesh with synchromesh on gears 2-6.
POWER: 150 kW @ 2,850 RPM. (ISO 1585) Oil capacity 5.3 litres. • Banjo type, fully floating, single reduction.
TORQUE: 539 Nm @ 1,700RPM. (ISO 1585) • Gear ratios to 1: • Hypoid type ring gear, 343mm diameter.
1st 2nd 3rd 4th 5th 6th Rev Oil capacity 5.5 litres.
COOLING SYSTEM
• 6 blade plastic cooling fan 500mm diameter 6.378 3.627 2.307 1.452 1.000 0.787 6.595 • Rear Axle Ratio:1
with thermatic fan clutch. Corrugated fin radiator • Maximum geared speed 113 km/h. (118km/h for 500S) Short/Med Auto PTO/Long Long/SiTEC 200
with fan shroud. Frontal area 3,820 cm2. ALLISON AT545 5.125 4.333 5.125 4.750
Coolant capacity 23.3 litres. 4 speed automatic (Optional transmission only
AIR INTAKE SYSTEM available on Medium/4,250mm wheelbase)
• Donaldson 11” two stage with vertical air intake • Oil capacity: 18.5 litres
stack and rain head. • Gear ratios to 1:
EXHAUST SYSTEM 1st 2nd 3rd 4th Rev
• Horizontal exhaust muffler with vertical exhaust stack. 3.454 2.254 1.407 1.000 5.025
• Exhaust brake, air controlled. • Maximum geared speed 106 km/h.

ISUZU-GENERAL MOTORS AUSTRALIA LTD A.C.N. 006 962 572. PLEASE NOTE: as the policy of I-GM is one of continual product improvement, all specifications and equipment are subject to change
without notice. No I-GM dealer or other person is authorised or permitted to give or make any statement, assertion or undertaking in relation to the quality, performance, characteristics, descriptions or
fitness for any purpose of any I-GM product or in connection with the supply of any I-GM product which is at variance with any written statement, assertion or undertaking on any of these subjects given
or made by I-GM in its published sales literature, and the company accepts no liability for any such unauthorised action. I-GM has franchised dealers in many parts of Australia, for the sale of service, parts
and the provision of service to the owners of I-GM products. Every endeavour is made to ensure that such dealers carry adequate stocks of service parts and are equipped to provide satisfactory service,
but makes no promise, other than that contained in the I-GM new vehicle warranty, that such parts or service facilities will be available or available at any specific location or at any particular time. A word
about this specification sheet. We have tried to make it as comprehensive and factual as possible. However, since the time of printing some of the information you will find here may have been updated.
Also, some of the equipment shown or described through this specification sheet may have been changed and/or is available at extra cost. And the right is reserved to make changes at any time without
notice, in prices, colours, materials, equipment and models. Your I-GM dealer has details and before ordering, you should ask him/her to bring you up to date.
RGS/IGM3111
 FRR 500
CABIN SPECIFICATIONS AND APPOINTMENTS
• Driver’s seat with mechanical suspension and
CAB EXTERIOR 3 way lumbar support. Adjustment for seat back CONTROLS
• All steel cab with welded strengthening ribs and recline, seat slide and weight control. • Left side combination stalk switch for exhaust
side door impact beams. Torsion bar assisted • Outboard reclining passenger seat with brake, windscreen wipers and washers,
manual tilt to 45°. under-seat storage drawer. Folding centre hazard lamps.
• 4 silicone filled rubber cab isolators. seat back with lockable compartment and tray. • Right side combination stalk switch for
• Cation electrodeposition primer. • Outboard lap/sash seat belts with emergency headlamps, high beam and turn signals.
• Bumper bar with step holes and footplate. locking retractors, centre lap seat-belt. • Engine idle speed adjust control.
• Halogen headlamps, hinged for easy bulb • Tilt/telescopic adjustable steering column, soft • Key operation for engine start and stop, external
replacement. Park lamps and cab clearance lamps. feel urethane steering-wheel. engine crank switch for service when cab is tilted.
• Turn signal lamps in front bumper and doors. • Easy entry grab handles on ‘A’ pillars. • 3 way switch for interior lamp activated by
• 2 speed wiper/washer with variable intermittent • Heater demister with 4 speed fan, 4 outlet vents driver’s door.
mode. Triple washer jets mounted on wiper arms. to screen, 5 fascia outlets, 5 foot outlets, demister
ducts to door glass. INSTRUMENTATION
• Tinted, laminated windscreen; tinted, toughened
side and rear glass. • Optional integrated air conditioning. • GAUGES: Speedometer, odometer, tripmeter and
• West Coast type rear-view mirrors with additional, • Eurovox AM/FM radio cassette with digital clock, tachometer. Gauges for coolant temperature,
separately adjustable spotter mirror on both sides. dash mounted. Remote seek/volume and mute fuel level and brake air pressure.
switch located on dash to right of steering wheel. • INDICATOR LAMPS: Turn signals, parking brake
• Alloy non-slip cab entry steps.
• Optional 6 stack CD player. on, high beam on, exhaust brake engaged.
• Lift up front access panel for clutch and Reversing lamp and beeper.
windscreen washer fluids, cab air filter screen. • DIN standard aperture in dash for CB radio.
• 12 Volt /100W cigarette lighter type electrical • WARNING LAMPS: With warning bulb check
• Engine and brake fluid check points at rear of cab. switch. Battery charge, oil pressure, low air
socket located in centre console.
• 24 Volt – 2 pin accessory plug in centre console. pressure, brake system, stop and tail light failure.
CAB INTERIOR
• Park brake activation lever at left side of
• Fully trimmed cab interior with cloth seat facings, driver’s seat. TOOLS
formed roof lining. Overhead storage lockers. • Lockable tool box. 7,000kg capacity
• Rear vision mirror.
• Driver and passenger sun visors. jack and wheel changing tools, tool kit.
• Passenger side assist grip.
• Pull out drinks holder in centre fascia, cigarette
lighter with ashtrays in doors. • Driver’s left foot rest.
• Cab exhaust vents rear/upper cab.
• Business card clip. Coat hook at rear of cab.
• Elastic mesh pocket on driver’s door.

CHASSIS SPECIFICATIONS

CHASSIS FRAME BRAKES WHEELS AND TYRES

• Parallel rail, ladder type channel section, • Air over hydraulic, dual circuit, front two leading, • 6.00 x 17.5, 6 stud disc wheels.
cold rivetted. rear dual two leading. Drum diameter front and • Number of wheels and tyres 7, including spare.
• Straight frame for easy body mounting. rear 320 mm. Total swept area 5127 cm2. Winch type spare wheel carrier.
Frame width 840 mm. • Air dryer. • 9.5R17.5 129/127L tubeless radial tyres
• Side member dimensions 225mm x 70mm x 6mm. • Nylon brake air tubing. front and rear
• Frame reinforcement angle section • Asbestos free lining material. • Type: Michelin XZA.
203mm x 64mm x 4.5mm at back of cab. • Park Brake: Load and speed ratings per tyre:
• Material HT540A high tensile, weldable steel. FRR 500 Short/Medium/Long/S: 1,850 kg (single) / 1,750 kg (dual) / 120 km/h.
Mechanical, internal expanding at rear of
SUSPENSION transmission. ELECTRICAL SYSTEM
Semi-elliptical, alloy steel tapered FRR 500 Auto/PTO: • Batteries – 2 x 12 volt / 65 amp/h, negative earth.
multi-leaf springs. Fully wrapped eye with Spring type, acting on rear wheels. • Alternator – 24 volt / 60 Amps (1.5kW)
greasable shackles. • Starter motor – 24 volt / 4.5 kW.
FRONT STEERING • Rear stop and tail lamps and licence plate lamp
• 1200mm x 70mm x 10mm x 8 leaves. • Fully integral power assisted recirculating ball type. with long leads for variable body mounting.
• Hydraulic, double acting, telescopic shock • Gear ratio 16.1 ~ 18.8 : 1. Turns lock to lock 4.1.
absorbers. • Gear driven vane type oil pump. Oil capacity
REAR 1.5 litres.
• Main: 1,300 x 70mm x 11mm x 8 leaves
Aux: 850 x 70mm x 10mm x 3 leaves
850 x 70mm x 11mm x 4 leaves

ISUZU NEW TRUCK WARRANTIES

STANDARD TRUCKPOWER WARRANTY* TRUCKPOWER EXTENDED WARRANTY OPTIONS#
NEW VEHICLE 2 years 100,000km
3 years / 150,000km 4 years / 200,000km 5 years / 250,000km
DRIVETRAIN 3 years 150,000km
CAB CORROSION 3 years unlimited

* Subject to the conditions outlined in the I-GM New Vehicle Warranty, the Isuzu FRR models carry a standard factory warranty which covers the owner: (i) for the entire vehicle, for the first
24 months or 100,000km (whichever comes first) (ii) for the powertrain, which runs concurrently for 36 months or 150,000km (whichever comes first) (iii) against cab corrosion, for 36 months and
unlimited kilometres.
# A TruckPower Extended Warranty as illustrated is available by purchase to cover the owner against the failure of original components, but excludes some components and expendable items such
as oil, filters, etc. Please consult with your Isuzu Dealer for full details obtainable from a dedicated brochure available to customers.