Question 

1
Correct
Mark 1.00 out of 1.00

Flag question

Question text
Which type of VLAN is identified by a VLAN ID between 1006 and 4094 and not contained
in updates of switches participating in a VTP domain?

Select one:

a.
pruned 

b.
transparent 

c.
native 

d.
extended 
Feedback
Your answer is correct.

Question 2
Correct
Mark 1.00 out of 1.00

Flag question

Question text
Which switchport mode makes the interface able to convert the link to a trunk
link?

Select one:

a.
switchport mode dynamic desirable

b.
switchport mode trunk
c.
switchport mode dynamic auto 

d.
switchport mode access 
Feedback
Your answer is correct.

Question 3
Correct
Mark 1.00 out of 1.00

Flag question

Question text
Which switchport mode puts the interface into permanent nontrunking ?

Select one:

a.
switchport mode dynamic desirable 

b.
switchport mode access

c.
switchport mode trunk

d.
switchport mode dynamic auto 
Feedback
Your answer is correct.

Question 4
Correct
Mark 1.00 out of 1.00

Flag question

Question text
Which type of router would an enterprise use to allow customers to access content anytime
and anyplace, regardless of whether they are at home or work?
Select one:

a.
branch routers 

b.
network edge routers

c.
modular routers

d.
service provider routers
Feedback
Your answer is correct.

Question 5
Correct
Mark 1.00 out of 1.00

Flag question

Question text
Which technology is required when switched networks are designed to include redundant
links?

Select one:

a.
link aggregation

b.
Spanning Tree Protocol 

c.
virtual LANs 

d.
virtual private networks
Feedback
Your answer is correct.
Question 6
Correct
Mark 1.00 out of 1.00

Flag question

Question text
What is the purpose of VTP?

Select one:

a.
It provides centralized management of VLANs in a multi-switch environment. 

b.
It is a Cisco proprietary protocol that manages trunk negotiation.

c.
It designates the management and native VLANs on multiple switches.

d.
It provides secure remote WAN access to the head office for teleworkers.

e.
It manages switches to ensure a loop-free environment. 
Feedback
Your answer is correct.

Question 7
Correct
Mark 1.00 out of 1.00

Flag question

Question text
Which network design solution will best extend access layer connectivity to host devices?

Select one:

a.
implementing routing protocol

b.
implementing EtherChannel

c.
implementing wireless connectivity

d.
implementing redundancy 
Feedback
Your answer is correct.

Question 8
Correct
Mark 1.00 out of 1.00

Flag question

Question text
Which scalable method must be implemented in order to provide inter-VLAN routing on a
switched network with more than 1000 VLANs?

Select one:

a.
configuring static routes on a Layer 2 switch device 

b.
 connecting each physical router interface to a different physical switch port, with each
switch port assigned to a different VLAN 

c.
 connecting a router interface to a switch port that is configured in trunk mode to route
packets between VLANs, with each VLAN assigned to a router subinterface 

d.
routing traffic internally to a Layer 3 switch device
Feedback
Your answer is correct.

Question 9
Correct
Mark 1.00 out of 1.00
 Flag question

Question text
Which combination of DTP modes set on adjacent switches will cause the link to become an
access link instead of a trunk link?

Select one:

a.
dynamic desirable - dynamic desirable 

b.
dynamic desirable - trunk 

c.
dynamic desirable - dynamic auto

d.
dynamic auto - dynamic auto 
Feedback
Your answer is correct.

Question 10
Correct
Mark 1.00 out of 1.00

Flag question

Question text
What is a characteristic of out-of-band device management?

Select one:

a.
Out-of-band device management requires a direct connection to a network interface. 

b.
It requires at least one network interface on the device to be connected and operational.

c.
It requires a terminal emulation client. 
d.
It requires Telnet, SSH, or HTTP to access a Cisco device. 
Feedback
Your answer is correct.

Question 11
Correct
Mark 1.00 out of 1.00

Flag question

Question text
A network administrator enters the following command sequence on a Cisco 3560 switch.
What is the purpose of these commands?
Switch(config)# interface gigabitethernet 0/1
Switch(config-if)# no switchport

Select one:

a.
to enable the Gi0/1 port as a bridge virtual interface 

b.
to shut down the Gi0/1 port

c.
to enable the Gi0/1 port as a switch virtual interface

d.
to make the Gi0/1 port a routed port 
Feedback
Your answer is correct.

Question 12
Correct
Mark 1.00 out of 1.00

Flag question

Question text
What is the function of PoE pass-through?

Select one:
a.
allows switches, phones, and wireless access points to receive power over existing Ethernet
cables from an upstream switch

b.
allows a multilayer switch to forward IP packets at a rate close to that of Layer 2 switching
by bypassing the CPU

c.
allows multiple physical switch ports to be aggregated together and act as a single logical
link to increase bandwidth on trunk links

d.
allows a switch to disable redundant Layer 2 paths in the topology to prevent Layer 2 loops 
Feedback
Your answer is correct.

Question 13
Correct
Mark 1.00 out of 1.00

Flag question

Question text
How much traffic is a 48-port gigabit switch capable of switching when operating at full wire
speed?

Select one:

a.
24 Gb/s, because this is the maximum forwarding rate on Cisco switches 

b.
1 Gb/s, because data can only be forwarded from one port at a time 

c.
48 Gb/s, by providing full bandwidth to each port 

d.
44 Gb/s, due to overhead requirements 
 Feedback
Your answer is correct.

Question 14
Correct
Mark 1.00 out of 1.00

Flag question

Question text
What is the term that is used for the area of a network that is affected when a device or
network service experiences problems?

Select one:

a.
broadcast domain

b.
failure domain 

c.
collision domain 

d.
user domain 
Feedback
Your answer is correct.

Question 15
Correct
Mark 1.00 out of 1.00

Flag question

Question text
Which switchport mode Puts the interface into permanent trunking mode and negotiates
to convert the neighboring link into a trunk link? 

Select one:

a.
switchport mode trunk
b.
switchport mode dynamic desirable 

c.
switchport mode access

d.
switchport mode dynamic auto 
Feedback
Your answer is correct.

Question 16
Correct
Mark 1.00 out of 1.00

Flag question

Question text
A PC is to access a web server on another network. Which inter-VLAN method will provide
the highest bandwidth at Layer 3 and also provide a default gateway for the PC?

Select one:

a.
router on a stick 

b.
trunked interface between the router and the switch

c.
multilayer switch with routing enabled

d.
multiple physical interfaces on the router, all connected to a Layer 2 switc
Feedback
Your answer is correct.

Question 17
Correct
Mark 1.00 out of 1.00

Flag question
 Question text
Which sentence correctly describes the SVI inter-VLAN routing method?

Select one:

a.
An SVI is needed for each VLAN. 

b.
Subinterfaces have to be created. 

c.
A physical interface is needed for every VLAN that is created. 

d.
The encapsulation type must be configured on the SVI. 
Feedback
Your answer is correct.

Question 18
Correct
Mark 1.00 out of 1.00

Flag question

Question text
Which feature could be used in a network design to increase the bandwidth by combining
multiple physical links into a single logical link?

Select one:

a.
trunk ports

b.
VLANs 

c.
EtherChannel

d.
subinterfaces 
 Feedback
Your answer is correct.

Question 19
Correct
Mark 1.00 out of 1.00

Flag question

Question text
An administrator is investigating a failure on a trunk link between a Cisco switch and a
switch from another vendor. After a few show commands, the administrator notices that the
the switches are not negotiating a trunk. What is a probable cause for this issue?

Select one:

a.
Both switches are in nonegotiate mode. 

b.
Switches from other vendors do not support DTP. 

c.
Both switches are in trunk mode.

d.
DTP frames are flooding the entire network. 
Feedback
Your answer is correct.

Question 20
Correct
Mark 1.00 out of 1.00

Flag question

Question text
A company has deployed four 48-port access layer switches to a switch block. For
redundancy each access layer switch will connect to two distribution layer
switches. Additionally, link aggregation will be used to combine 10 Gbps interfaces to form
20 Gbps trunk links from the access layer switches to the distribution layer switches. How
many switch ports on the access layer switches will be available in the switch block to
support end devices?
Select one:

a.
188 

b.
184 

c.
176 

d.
192 
Feedback
Your answer is correct.