Application: 1990 Ford Bronco 1990 Ford Bronco

1990 Ford Bronco
1983-92 AUTOMATIC TRANSMISSIONS Ford AOD Overhaul
1983-92 AUTOMATIC TRANSMISSIONS
Ford AOD Overhaul
APPLICATION
TRANSMISSION APPLICATIONS
Models Engine Size
1983-91 LTD Crown Victoria, Grand Marquis & Town Car 5.0L EFI & 5.8L EFI
1983-91 Crown Victoria, Grand Marquis & Crown Victoria 5.0L SEFI
Police
1984-86 Capri & Mustang 5.0L EFI
1983-87 Continental 5.0L EFI
1984-85 Continental & Mark VII 2.4L EFI
1983-92 Cougar & Thunderbird 3.8L EFI & 5.0L HO
1989-92 Thunderbird 3.8L SC
1984-92 Mark VII LSC & Mustang 5.0L HO
1986-92 F150/250 & Bronco 4.9L & 5.0L EFI
1983-89 E150 4.9L
1983-93 E150/250 5.0L EFI
IDENTIFICATION
Automatic Overdrive Transmission (AOD) is identified by the code letter "T". The identification code letter is
found on the lower line of Vehicle Certification Label under TR. This label is attached to driver's side door lock
post.
The transmission model may be identified by a metal tag attached to transmission by the middle left hand
extension housing retaining bolt. Top line of tag shows transmission model number and line shift code. Bottom
line on tag shows the build date code. See Fig. 1 .
jueves, 26 de enero de 2023 12:04:48

12:04:44 a. m. Page 1 © 2011 Mitchell Repair Information Company, LLC.
1990 Ford Bronco
Fig. 1: Service Identification Tag

Courtesy of FORD MOTOR CO.
DESCRIPTION
AOD is a 4-speed, fully automatic transmission which combines automatic shifting with 2 fuel saving features:
an overdrive gear ratio and mechanical lock-out split torque path in 3rd gear. AOD transmission differs from
similar Ford C-6 automatic transmissions in that the planetary gear set operates in 4th gear. See Fig. 6 .
LUBRICATION & ADJUSTMENTS

See appropriate TRANSMISSION SERVICING - A/T article in TRANSMISSION SERVICING.
ON-VEHICLE SERVICE
NOTE: See Fig. 52 and Fig. 53 for exploded view of internal parts, thrust washer and
needle bearing locations.
VALVE BODY ASSEMBLY
Removal
1. Raise vehicle on hoist. Remove exhaust system, if necessary. Loosen oil pan retaining bolts and allow
transmission fluid to drain. Remove oil pan and gasket. Discard gasket.
2. Remove 3 filter-to-valve body retaining bolts and remove filter, grommet and gasket. Remove detent
jueves, 26 de enero de 2023 12:04:44 a. m. Page 2 © 2011 Mitchell Repair Information Company, LLC.
1990 Ford Bronco
spring retaining bolt and spring. Remove retaining bolts. Note positions and lengths of bolts for
reassembly reference.
3. Remove valve body and gasket from transmission. For service or repair of valve body assembly, see
VALVE BODY ASSEMBLY under COMPONENT DISASSEMBLY & REASSEMBLY.
Installation
1. Using guide pins, position valve body (with new gasket) in case. Ensure inner manual lever and inner
T.V. lever are engaged. Install and tighten valve body retaining bolts to specification. See TORQUE
SPECIFICATIONS .
2. Install and tighten detent spring and retaining bolts. Remove guide pins and install 2 remaining valve
body retaining bolts to specification. Load throttle lever torsion spring against separator plate. Install new
filter and gasket. Install oil pan with new gasket and refill with fluid. Install exhaust system, if removed.
OVERDRIVE SERVO ASSEMBLY
Removal
1. Remove valve body. See VALVE BODY ASSEMBLY . Hold overdrive band against drum with
screwdriver to prevent band movement when servo is removed. Depress overdrive servo piston cover and
remove retaining snap ring. See Fig. 2 .
2. Using Remover (T80L-77030-B), apply air pressure to servo piston release passage to remove piston
cover and spring. See Fig. 23 . Separate piston from cover. Remove rubber seals from piston and cover.
Installation
1. Install new seals on piston and cover. Lubricate piston seals with ATF or petroleum jelly, then install
piston into cover.
2. Lubricate cover seals and overdrive servo pocket in transmission case. Assemble spring to piston. Install
assembly into case pocket. Ensure servo rod contacts overdrive band apply pocket. Depress servo cover
and install retaining snap ring. Install valve body.
LOW-REVERSE SERVO ASSEMBLY
Removal
1. Remove valve body, see VALVE BODY ASSEMBLY . Depress low-reverse servo piston cover and
remove retaining snap ring and cover. See Fig. 2 .
2. Remove piston and spring from case by applying compressed air to low-reverse servo release passage in
case. See Fig. 23 . Cover piston pocket to prevent piston from falling out of case. Using Remover (T80L-
77030-B), apply air to servo piston release passage to remove piston, if necessary.
CAUTION: Low-reverse servo piston is under spring pressure and may spring free
from case when cover is removed.
Installation
1990 Ford Bronco
To install, reverse removal procedure. Ensure servo piston is installed with same length rod as was removed.
2-3 ACCUMULATOR PISTON
Removal
Remove valve body. See VALVE BODY ASSEMBLY . Depress 2-3 accumulator piston cover. Remove
retaining snap ring, cover, and spring. See Fig. 2 . Remove accumulator piston. Remove accumulator seals from
piston.
Installation
To install, reverse removal procedure. Prior to installation, lubricate piston seals and piston pocket in case.
Fig. 2: Identifying Accumulator & Servo Locations
1990 Ford Bronco
EXTENSION HOUSING BUSHING & REAR OIL SEAL
Removal
1. Raise vehicle on hoist. Mark drive shaft yoke and axle companion flange for reassembly reference.
Disconnect drive shaft from transmission. Remove oil seal using Puller (T74P-77248-A).
2. Remove bushing using Puller (T77L-7697-A), taking care not to damage output shaft splines.
Installation
Install new bushing into extension housing using Driver (T80L-77034-A). Install new seal into housing using
appropriate seal installer. Coat inside diameter of rubber portion of seal and yoke splines with lubricant. Install
drive shaft.
EXTENSION HOUSING
Removal
1. Raise and support vehicle. Remove exhaust system components as necessary for access. Disconnect
parking brake cable from equalizer (if equipped). Mark drive shaft yoke and axle companion flange for
reassembly reference. Remove drive shaft and disconnect speedometer cable from extension housing.
2. Remove engine rear support-to-extension housing retaining bolts. Raise transmission just enough to
remove weight from rear support. Remove rear support-to-crossmember retaining bolt and remove rear
support.
3. Lower transmission and remove extension housing retaining bolts. Slide housing off output shaft and
allow fluid to drain. Remove and discard extension housing-to-case gasket.
Installation
1. Clean mating surface on transmission and extension housing. Position new gasket on transmission. Slide
extension housing into place.
2. Clean bolts and case holes for 2 bottom bolts and lower right hand corner bolt (as viewed from rear of
extension housing). Coat bolts with Teflon tape and install. Install remaining bolts and tighten all to
specification. See TORQUE SPECIFICATIONS . To complete installation, reverse removal procedure.
GOVERNOR ASSEMBLY
Removal
1. Remove extension housing. See REMOVAL procedure under EXTENSION HOUSING . Remove
governor-to-output shaft retaining snap ring. Using a mallet, tap governor assembly off output shaft. See
Fig. 3 .
2. Remove governor drive ball. Remove governor-to-counterweight retaining screws and lift governor from
counterweight. For complete repair and servicing, see GOVERNOR ASSEMBLY under COMPONENT
DISASSEMBLY & REASSEMBLY.
1990 Ford Bronco
Installation
1. Lubricate governor parts with clean transmission fluid. Ensure valve moves freely in bore. Position
governor body on counterweight with cover facing toward front of vehicle. Install and tighten 2 retaining
screws to specification. See TORQUE SPECIFICATIONS .
2. Position governor drive ball into pocket on output shaft. Align keyway in counterweight with drive ball
and drive assembly onto output shaft with mallet. Install governor-to-output shaft retaining snap ring. To
complete installation, reverse removal procedure.
Fig. 3: Removing Governor Assembly

INTERNAL & EXTERNAL SHIFT LINKAGE
1990 Ford Bronco
NOTE: On some vehicles it may be necessary to loosen fan shroud and lower
transmission to remove linkage.
Removal
1. Raise vehicle on hoist. Disconnect any interfering exhaust system components. Apply penetrating oil to
outer throttle lever retaining nut to prevent breaking inner throttle lever. See Fig. 4 .
2. Hold outer throttle lever stationary and remove retaining nut and lock washer. Move lever and T.V. rod or
cable out of way for clearance. Disconnect manual rod from manual lever at transmission.
3. Loosen oil pan retaining bolts and allow fluid to drain. Remove oil pan. Remove manual lever detent
spring and roller assembly.
4. Remove manual lever retaining pin carefully using a sharp narrow screwdriver. Note assembled position
of T.V. lever torsion spring. Remove torsion spring.
5. Securely hold inner manual lever and use a 21 mm wrench to break manual lever attaching nut free. DO
NOT allow tools to contact detents. Remove outer manual lever from case.
6. Remove inner throttle lever and shaft assembly. Remove inner manual lever and parking pawl rod
assembly. Disconnect parking pawl rod from inner manual lever. Remove manual lever oil seal using a
screwdriver.
Installation
1. Install new manual lever oil seal into case using appropriate driver. With manual lever nut on inner
throttle lever, slide inner throttle lever through inner manual lever. See Fig. 5 .
2. Install outer manual lever in case ensuring lever is in proper position (either up or down). Install inner
throttle lever and shaft into outer manual lever.
3. Tighten manual lever attaching nut to specification. See TORQUE SPECIFICATIONS . Ensure flats
are aligned. Install T.V. lever torsion spring. Push manual lever into case. Ensure inner manual lever pin
is engaged on manual valve detent slot and inner throttle lever is engaged on T.V. valve.
4. Neutral start switch plunger must also contact cam surface of inner manual lever. Install new manual
lever retaining pin in case. Pin must be flush or below pan gasket surface. Install new throttle lever seal.
5. Install detent spring. Install throttle valve outer lever. DO NOT push inner lever past throttle valve, lock
washer and nut. Tighten retaining nut to specification. See TORQUE SPECIFICATIONS .
6. Check Park function and operation of T.V. and manual levers. Connect shift linkage. Adjust linkage as
necessary. See appropriate TRANSMISSION SERVICING - A/T article in TRANSMISSION
SERVICING section.
1990 Ford Bronco
Fig. 4: Identifying Manual & Throttle Linkage Components

1990 Ford Bronco
Fig. 5: Exploded View of Manual & Throttle Linkage

NEUTRAL SAFETY SWITCH
See appropriate TRANSMISSION SERVICING - A/T article in TRANSMISSION SERVICING.
TROUBLE SHOOTING
NOTE: Always check fluid level and condition, linkage adjustment and vacuum
diaphragm prior to trouble shooting.
1990 Ford Bronco
SYMPTOMS
Slow Initial Engagement
Plugged filter or low main control pressure.
Rough Initial Engagement
Idle speed too high. Sticking valve body or high control valve pressure.
Delayed Or No Forward Engagement, Reverse Okay
Low main control pressure. Forward clutch assembly burnt or damaged. Valve body sticking. Improper valve
body torque. Forward clutch cylinder check ball leaking or seal rings leaking. Forward clutch stator support seal
rings leaking.
Delayed Or No Reverse Engagement, Forward Okay
Reverse clutch stator support seal rings leaking or clutch assembly burnt. Valve body sticking. Improper valve
body torque. Reverse clutch piston check ball leaking or seal rings leaking. Low main control pressure.
Fig. 6: Cross-Sectional View of AOD Transmission

Delayed Or No Reverse Engagement And/Or No Engine Braking In Manual Low
Planetary low one-way clutch damaged. Low reverse band burnt. Low reverse servo piston seal leaking.
No Engine Braking In Manual 2nd
Intermediate band improperly adjusted. Overdrive servo leaking. Intermediate one-way clutch damaged. Glazed
1990 Ford Bronco
intermediate band.
Forward Engagement Slips, Shudders Or Chatters On Engagement
Plugged filter. Low main control pressure. Valve body sticking or improperly torqued. Defective forward clutch
assembly. Low one-way clutch damaged.
Reverse Engagement Slips, Shudders Or Chatters On Engagement
Plugged filter. Low main control pressure. Reverse band improperly adjusted or damaged. Low one-way clutch
damaged. Reverse servo leaking. Reverse clutch piston seals defective or clutch assembly defective.
Starts Up In 2nd Or 3rd
Improper intermediate band adjustment. Defective governor. Sticking or loose valve body. Cross leaks between
valve body and case mating surfaces.
Incorrect Shift Points, Harsh Or No Upshift
Sticking or improperly adjusted T.V. rod (high T.V. pressure). Improper control valve pressure. Dirty or
sticking valve body or governor assembly. Improper speedometer gear.
Early, Mushy, Soft Or Slipping Upshift
Low main control pressure. Dirty or sticking valve body or governor. Leaking or improperly torqued valve
body. Sticking or improperly adjusted T.V. rod (low T.V. pressure).
Erratic Shifts
Poor engine performance. Improper valve body bolt torque. Valve body or governor sticking. Governor
collector body seal rings leaking. T.V. linkage sticking.
No Forced Downshift
Improperly adjusted or sticking T.V. rod. Dirty or sticking valve body or governor. Improper oil control
pressure.
Transmission Overheats
Engine idle too high. Engine cooling system defective. Transmission pressure too low. Restriction in cooler or
cooler lines. Seized convertor one-way clutch.
Transmission Clunk Or Squawk During Upshift
Intermediate clutch piston bleed hole blocked or not positioned at 12 o'clock. Anti-Clunk spring out of position.
Converter damper spring broken.
Transmission Noisy (Valve Resonance)
1990 Ford Bronco
Improper control valve pressure. Internal oil pressure leaks or pump cavitation. Grounding cooler lines. Dirty or
sticking valve body.
Harsh Initial Engagement Into Drive
Idle speed too high. Too much forward clutch clearance. Improper oil control pressure.
Delayed Reverse Engagement
Sticking pressure regulator boost valve. Leaking rear servo piston or cover.
Slips & Chatters When Hot, Delayed Drive & Reverse
Worn pump. Pressure regulator valve sticking when hot.
No Forward After A Stop
The 3-4 shift valve stuck in upshifted position.
No Reverse
Rear servo piston not contacting rear band (may happen during overhaul).
No 2nd, 4th Or Reverse
Broken weld on sun gear shell.
No 2nd Or 4th, Reverse Okay
Stuck 1-2 shift valve.
No 3-4 Upshift
The 3-4 shift valve stuck in downshifted position. The 3-4 shift valve bore plug leaking. Leaking orifice control
valve bore plug. Leaking direct clutch and oil control rings. Cut direct clutch piston outer lip seal. Large oil
control ring leaking on 2-3 accumulator piston. Leaking governor oil control rings or worn ring area in case
bore. Worn case or direct clutch drum bushing. Governor loose on output shaft. Sticking 4-3 back-out valve.
No 3rd Or 4th
Broken torque converter assembly. Burnt direct clutch. The 2-3 shift valve stuck in downshifted position.
2-3 Squawk
Wrong ATF (Dexron II or Mercon only). Direct clutch circuit leaks (oil control rings, outer piston lip seal,
leaking piston check ball). Worn direct drum bushing. Worn case bushing. Worn ring area in case bore. Worn
friction plates.
Clacking Noise Or Squawk, Intermediate Buck On Deceleration
1990 Ford Bronco
Week torque converter damper spring (damper assembly is bottoming out). This can cause direct clutch failure.
3-4 Slip
Leaking overdrive servo piston or cover seals. Wrong size overdrive servo piston and cover. Throttle linkage
adjustment.
Neutral Condition On 3-4 Upshift
Missed overdrive band when installing overdrive servo piston (may happen during overhaul). Band anchor out
of position.
Bucking On Deceleration & Kills Engine When Stopping
Governor valve in high gear position.
Chatters Or Bucks On Acceleration Or Deceleration In 4th Gear
Engine performance problem (EGR, fuel system, etc.).
No 3-4 Upshift Until 50 MPH, Or Until Accelerator Pedal Is Released Slightly
Condition normal if valve body has 2-piece 3-4 shift valve. Throttle linkage adjustment.
Harsh 4-3 Or 4-2 Downshift
Sticking overdrive servo regulator valve. Forward clutch apply hole in separator plate larger than .100" (2.54
mm) in diameter.
Bearing Whine In All Gear Positions Except 3rd & 4th
Bad bearing between direct clutch drum and output shaft flange.
CLUTCH & BAND APPLICATION CHART
CLUTCH & BAND APPLICATION CHART

Selector Lever Position Elements In Use
"O" Overdrive
1st Forward Clutch, Planetary One-Way Clutch
2nd Intermediate Clutch, Forward Clutch &
Intermediate One-Way Clutch
3rd Forward Clutch, Intermediate Clutch &
Direct Clutch
Overdrive Overdrive Band, Intermediate Clutch &
Direct Clutch
"D" (Drive)
1st Forward Clutch, Planetary One-Way Clutch
1990 Ford Bronco
2nd Intermediate Clutch, Forward Clutch &

3rd Forward Clutch, Intermediate Clutch &
Direct Clutch
"2" (Intermediate) (2nd) Forward Clutch, Intermediate Clutch &
"1" (Low) (1st) Forward Clutch, Planetary One-Way Clutch &
Low Reverse Band
"R" (Reverse) Reverse Clutch & Low Reverse Band
TESTING
ROAD TEST
NOTE: The AOD will not shift into Overdrive at wide open throttle, and will not make a
4th to 1st gear downshift. It will automatically downshift from Overdrive to 3rd
gear when road speed drops below 35 MPH.
1. Check minimum throttle upshifts in Overdrive. Transmission should start in 1st gear, shift to 2nd, then
shift to 3rd, and finally shift to 4th gear at approximately the speeds shown in SHIFT SPEEDS
SPECIFICATIONS (MPH) tables.
2. With transmission in 4th gear (Overdrive), completely depress accelerator pedal. Transmission should
downshift to 3rd or 2nd gear, depending on vehicle speed. See SHIFT SPEEDS SPECIFICATIONS
(MPH) tables.
3. Since closed throttle downshifts are extremely difficult to detect, it may be necessary to attach 0-100 psi
(0-7.0 kg/cm2 ) pressure gauges to forward and direct clutch pressure taps in order to detect Overdrive to
3rd gear and 3rd to 2nd gear coast downshifts. See Fig. 7 .
4. With gauges attached, a 4th to 3rd gear coast (closed throttle) downshift is detected by the application of
the forward clutch. Pressure will increase from 0-60 psi (0-4.2 kg/cm2 ). The 3rd to 2nd gear downshift is
detected by release of direct clutch pressure. Pressure will decrease from 60-0 psi (4.2-0 kg/cm2 ).
5. When selector lever is moved from either Overdrive or Drive ranges to "1" position, transmission should
downshift into 2nd gear if vehicle speed is above 25 MPH, and into 1st gear if speed is less than 25 MPH.
1990 Ford Bronco
Fig. 7: Identifying Control Pressure Taps

CONTROL PRESSURE TEST
NOTE: When testing line pressure, 2 readings must be taken: one at Idle position (zero
T.V.) and the other at WOT (full T.V.).
1990 Ford Bronco
1. Connect a 0-300 psi (0-21.1 kg/cm2 ) pressure gauge to main line pressure port tap on left side of
transmission case just above control levers. See Fig. 7 . Gauge hose must be long enough to read gauge
while operating engine.
2. Connect a 0-100 psi (0-7.0 kg/cm2 ) pressure gauge to T.V. pressure tap at right side of transmission case.
See Fig. 7 . Gauge hose must be long enough to read gauge while operating engine. Ensure T.V. linkage
is properly adjusted.
CAUTION: Pressure gauges affect transmission shift quality. DO NOT accelerate

or decelerate rapidly. Possible transmission failure could result.
3. With engine at normal operating temperature, apply parking and service brakes. Check line pressure and
throttle pressure in all ranges. Pressure should be approximately as specified. See CONTROL
PRESSURE SPECIFICATIONS .
NOTE: Pressure test at idle position must be taken with engine at warm idle speed.
Pressure test at WOT position should be taken at full stall conditions. Run
engine at a fast idle in "N" to cool fluid between tests.
CONTROL PRESSURE SPECIFICATIONS

Line Pressure psi T.V. Limit Pressure (1)
Throttle Position (kg/cm2 ) psi (kg/cm2 )
Idle
"R" 75-90 (5.3-6.3) 0
All Other Ranges 55-65 (3.9-4.6) 0
WOT Stall
In "R" - 3.8L & 4.9L 241-279 (16.9- 74-86 (5.2-6.0)
19.6)
In "R" - All Others 250-290 (17.5- 79-91 (5.5-6.4)
20.3)
All Other Ranges - 3.8L & 4.9L 176-204 (12.4- 74-86 (5.2-6.0)
14.3)
All Other Ranges - All Others 180-215 (12.6- 79-91 (5.5-6.4)
15.1)
(1) With governor pressure at zero.
CONTROL PRESSURE TEST RESULTS
Low In "P"
Valve body loose, faulty main oil regulator valve sticking or low-reverse servo leakage.
Low In "R"
1990 Ford Bronco
Reverse clutch or low-reverse servo leakage. Valve body loose.
Low In "N"
Loose valve body or main oil regulator valve sticking.
Low In "O/D"
Faulty forward clutch, Overdrive servo, main oil regulator valve or loose valve body.
Low In "D"
Forward clutch leakage. Overdrive servo leakage.
Low In "1st"
Leakage at forward clutch or low-reverse servo or overdrive servo.
Low At Idle In All Ranges
Low fluid level, restricted intake screen or filter, loose valve body bolts, pump leakage, case leakage, faulty
valve body, excessively low engine idle, fluid too hot or main regulator valve sticking.
High At Idle In All Ranges
Check for T.V. linkage adjustment and condition and for faulty valve body.
Pressure Okay At Idle But Low At WOT
Internal leakage, pump leakage, restricted intake screen of filter, damaged or out of adjustment T.V. valve
linkage. Also check for sticking T.V. or sticking T.V. limit valve in valve body.
Line Pressure And T.V. Pressure High
Replace valve body.
Line Pressure and T.V. Pressure Low
Check T.V. adjustment. If T.V. adjustment is okay, replace valve body.
DIRECT CLUTCH PRESSURE TEST
1. Attach accurate 0-300 psi (0-21.1 kg/cm2 ) pressure gauges to the forward and direct clutch pressure taps
on right side of transmission. See Fig. 7 . Gauge hose must be long enough to read gauge while road
testing vehicle.
2. Drive vehicle. When pressure is applied to direct clutch, note difference between line pressure on forward
clutch gauge and direct clutch gauge. If difference is less than 15 psi (1.1 kg/cm2 ), direct clutch circuit is
good.
1990 Ford Bronco
3. If difference is greater than 15 psi (1.1 kg/cm2 ), there could be a leak in direct clutch pressure circuit.
SHIFT SPEED SPECIFICATIONS (MPH)
NOTE: Shift speeds shown are approximate. All shift speeds may vary somewhat due
to production tolerances and emission control equipment. See Fig. 8 -Fig. 22 .
NOTE: Specifications given are for 1991 models; 1992 models are similar. 1992
specifications are not available at time of publication. Ensure all tires are
factory recommended size.
Fig. 8: 5.0L Crown Victoria & Grand Marquis PKA-ET (2.73 Axle Ratio)
1990 Ford Bronco
Fig. 9: 5.8L Crown Victoria Police PKA-ER, ES (2.73 Axle Ratio)
1990 Ford Bronco
Fig. 10: 5.0L Crown Victoria & Grand Marquis/Crown Victoria Police PKA-EU (3.55 Axle Ratio)
1990 Ford Bronco
Fig. 11: 5.0L Crown Victoria & Grand Marquis Crown Victoria Police PKA-EU, EV, EY (3.08 Axle
Ratio)
1990 Ford Bronco
Fig. 12: 5.0L Crown Victoria & Grand Marquis Crown Victoria Police PKA-EU, EV, EY (3.27 Axle
Ratio)
1990 Ford Bronco
Fig. 13: 3.8L SC Thunderbird PKA-EU (3.27 Axle Ratio)
1990 Ford Bronco
Fig. 14: 5.0L HO Mark VII LSC PKA-EH (3.27 Axle Ratio)
1990 Ford Bronco
Fig. 15: 3.8L Cougar & Thunderbird PKA-DV (3.27 Axle Ratio)
1990 Ford Bronco
Fig. 16: 5.0L Cougar & Thunderbird PKA-FJ, FK (2.73 & 3.08 Axle Ratio)
1990 Ford Bronco
Fig. 17: 5.0L HO Mustang PKA-FH (3.27 Axle Ratio)
1990 Ford Bronco
Fig. 18: 5.0L HO Mustang PKA-FE (2.73 Axle Ratio)
1990 Ford Bronco
Fig. 19: 4.6L Town Car PKA-FF (3.27 Axle Ratio)
1990 Ford Bronco
Fig. 20: 4.6L Town Car PKA-FG (3.55 Axle Ratio)
1990 Ford Bronco
Fig. 21: Bronco, Light Truck & Van PKB-AW, AZ, AX (3.55 & 3.73 Axle Ratio)
1990 Ford Bronco
Fig. 22: Bronco, Light Truck & Van PKB-AY (4.10 Axle Ratio)
GOVERNOR CHECK
Accelerate vehicle quickly to 25 MPH and back off throttle completely. If governor is operating properly,
transmission will shift to 3rd gear.
STALL SPEED TEST
Testing Precautions
When performing stall test, DO NOT hold throttle open longer than 5 seconds. Allow a cooling period of 15
seconds with transmission in "N" and engine speed at 1000 RPM between each test. If engine speed exceeds
maximum limits shown, release accelerator immediately, as this is an indication of clutch or band slippage.
Testing Procedure
Bring engine to normal operating temperature. Apply parking and service brakes. Stall test transmission in each
driving range at WOT. Note maximum RPM obtained. Engine speed should be within limits. See STALL
SPEED SPECIFICATIONS . If maximum RPM obtained is not within specifications, see STALL SPEED
1990 Ford Bronco
TEST RESULTS .
STALL SPEED SPECIFICATIONS

Application Engine 1989 RPM 1990-92 RPM
Cougar & Thunderbird 3.8L 2138-2493 2156-2510
Thunderbird 3.8L SC 2293-2668 2295-2676
Crown Victoria, Grand 4.6L 2V N/A 2000-2334
Marquis & Town Car
Mustang & Mark VII 5.0L HO+ 2124-2509 2089-2465
Crown Victoria & Grand 5.0L SEFI N/A 2073-2405
Marquis
Crown Victoria Police 5.0L SEFI N/A 2073-2405
Cougar & Thunderbird 5.0L HO N/A 2017-2460
Crown Victoria & Grand 5.0L EFI 2035-2351 2014-2326
Marquis
Crown Victoria Police 5.8L HO VV 1568-1885 1552-1862
"E" & "F" Series 4.9L 2042-2351 2055-2361
Bronco, "E/F" Series 5.0L EFI 2092-2449 2098-2456
STALL SPEED TEST RESULTS
High Stall Speeds Or Slip
In "OD" or "D" position - Check planetary one-way clutch.

In "OD", "D" and "1" position - Check forward clutch.
In "R" position - Check reverse clutch and/or low-reverse band.
In all ranges -- Check T.V. control adjustment and perform control pressure test.
Low Stall Speeds
Check engine tune-up. If okay, go to next step.

Check torque converter using bench test for stator one-way clutch slippage.
AIR PRESSURE TESTS
1. A "No Drive" condition can exist even with correct transmission fluid pressure, because of inoperative
clutches or bands. The inoperative units can be located by substituting air pressure for fluid pressure to
determine location of malfunction.
2. To make air pressure checks, drain transmission fluid. Remove oil pan and control valve body assembly.
Install Adapter Plate (T82L-7006-A), with Adapter Plate Attaching Screws (T82P-7006-C) and control
valve body gasket in place of control valve body. Tighten attaching screws 80-100 INCH lbs. (9-11 N.m).
With a rubber-tipped air nozzle, apply air pressure in indicated locations. See Fig. 23 .
3. If servo or accumulator does not move when tested, clean and inspect servo or accumulator to locate
cause. See appropriate component under ON-VEHICLE SERVICE . If during test 2 clutches apply or
1990 Ford Bronco
clutch fails to operate, check fluid passages in case and front pump for blockage or damage.
NOTE: Air pressure should be regulated between 40 psi (2.8 kg/cm2 ) and 90 psi (6.3
kg/cm2 ). Compressed air used for test should be filtered and dry to avoid
contaminating transmission fluid.
Fig. 23: Identifying Air Pressure Test Apply Ports on Adapter Plate
Reverse Clutch
Apply air pressure to reverse clutch passage. A dull thud can be heard when clutch piston is applied, or
1990 Ford Bronco
movement can be felt by placing fingertips on clutch drum.
Forward Clutch
Apply air pressure to forward clutch apply passage in adapter plate. A dull thud can be heard when clutch piston
is applied, or movement can be felt by placing fingertips on input shell.
Intermediate Clutch
Apply air pressure to intermediate clutch apply passage in adapter plate. A dull thud can be heard or felt if
clutch is operating properly.
Overdrive Servo
Apply air pressure to Overdrive servo apply passage. Operation of band is indicated by tightening of band
around reverse clutch drum. A thud can be felt on servo cover when servo returns to release position as a result
of spring force from release spring; band will then relax.
Low-Reverse Servo
Apply air pressure to low-reverse servo apply passage. A dull thud can be heard when low-reverse band tightens
around planetary drum. Movement of ring gear should also be detected.
Direct Clutch
Apply air pressure to direct clutch passage in adapter plate. A dull thud can be heard or felt on drive shaft if
clutch is operating properly.
2-3 Accumulator
Apply air pressure to 2-3 accumulator passage. Accumulator piston should unseat and can be detected by
inserting a metal rod into 2-3 piston hole. When piston unseats, rod will move.
Governor
1. In order to check lines to governor passage and governor to valve body passage, drive shaft crossmember
and extension housing must be removed. Apply air pressure to governor passage while holding finger
near governor valve. Air should be felt exiting valve.
2. To air pressure check governor to valve body passage, governor must be removed. Apply air pressure to
passage while holding finger over holes in output shaft. Air should be felt exiting one of the holes.
FLUSHING CONVERTER
NOTE: Torque converter is a sealed unit and cannot be disassembled for service.
Replace if found to be defective. The following tests will identify a defective
converter.
Whenever transmission has been disassembled to replace worn or damaged parts, or because valve body sticks
1990 Ford Bronco
due to foreign material, converter and oil cooler must be cleaned using a mechanically agitated cleaner
(Rotunda 1400028). Under no conditions should converter or oil cooler be cleaned by hand agitation using
solvent.
LEAK TEST
If torque converter welds indicate leakage, attach Torque Converter Leak Detector (Rotunda 7200004) to
converter and follow detector kit instructions.
END PLAY CHECK
1. Insert Tester (T80L-7902-A) into converter pump drive hub until hub bottoms. Expand sleeve in turbine
spline by tightening threaded inner post of tester until sleeve is securely locked into spline.
2. Attach a dial indicator to tool with button on indicator on converter pump drive hub. Zero dial face. Lift
tool upward as far as tool will go and note indicator reading. See Fig. 24 .
3. Reading is total end play of turbine and stator. If end play exceeds .023" (.58 mm) for new or rebuilt
converter, or .050" (1.27 mm) for used converter, replace torque converter assembly.
1990 Ford Bronco
Fig. 24: Measuring Torque Converter End Play

STATOR ONE-WAY CLUTCH CHECK
1. Insert one-way clutch Holding Wire (T77L-7902-R) into one of the grooves in stator thrust washer. Insert
Torque Adapter (T76L-7902-C) into converter pump drive hub so as to engage one-way clutch inner race.
2. Attach a torque wrench to torque adapter. With clutch holding wire held stationary, turn torque wrench
counterclockwise. See Fig. 25 . The converter one-way clutch should lock-up and hold a 10 ft. lb. (14
N.m) force. One-way clutch should rotate freely in a clockwise direction.
3. Repeat lock-up test in at least 5 different locations around torque converter. If clutch fails to lock-up and
hold, replace torque converter.
1990 Ford Bronco
Fig. 25: Checking Stator One-Way Clutch

DAMPER & HUB ASSEMBLY
1. Place torque converter in Holding Fixture (T83L-7902-A3). Place Turning Device (T83L-7902-A1 ) in
converter. Ensure splines are engaged. Install Pilot Guide (T83L-7902-A2) over turning device and onto
impeller hub.
2. Hold converter snug in holding fixture and rotate shaft clockwise and counterclockwise with 50 ft. lbs.
(68 N.m), using a 3/4" socket and torque wrench. See Fig. 26 . Shaft should not move more than 4
degrees. If shaft exceeds specification or grinding noise is heard, replace converter.
1990 Ford Bronco
Fig. 26: Checking Converter Damper & Hub

STATOR INTERFERENCE CHECK
Stator-To-Impeller Interference Check
1990 Ford Bronco
1. Position front pump assembly on bench with spline end of stator shaft pointing up. Mount converter on
pump so splines of one-way clutch inner race engage splines of stator support and converter hub engages
pump drive gear.
2. While holding pump stationary, rotate converter counterclockwise. Converter should rotate freely without
interference or scraping within assembly. Should interference or a scraping condition exist, or if converter
does not rotate freely, replace converter unit.
Stator-To-Turbine Interference Check
1. Place converter on bench, front side down. Install front pump assembly to engage mating splines of stator
support, stator and pump drive gear lugs.
2. Install input shaft, engaging splines with turbine hub. While holding pump stationary, rotate turbine with
input shaft.
3. Turbine should rotate freely in both directions without interference or noise. If interference or noise
exists, stator front thrust washer may be worn; converter should be replaced.
REMOVAL & INSTALLATION

TRANSMISSION
See appropriate TRANSMISSION REMOVAL - A/T article in TRANSMISSION SERVICING.
DISASSEMBLY
TRANSMISSION
1. Remove torque converter. Mount transmission in a holding fixture. Remove oil pan and gasket. Remove
oil filter, grommet, and gasket.
2. Remove detent spring and roller assembly. Remove valve body retaining bolts and lift off valve body and
gasket. Note bolt positions for reassembly.
3. Remove 2-3 accumulator assembly, low-reverse servo assembly, and overdrive servo assembly by
pushing down on servo covers and removing retaining snap rings. Note length of low-reverse servo piston
rod for reassembly reference. See Fig. 2 .
NOTE: Length of low-reverse piston rod may vary. Three possible rod lengths are
available.
4. Remove direct drive shaft by pulling it straight out from case. See Fig. 27 . Remove pump body retaining
bolts. Remove pump from case using 2 slide hammers installed in opposite pump retaining bolt holes.
Remove pump-to-case gasket.
5. Grasp turbine shaft and pull intermediate clutch pack, intermediate one-way clutch, reverse clutch, and
forward clutch from transmission case as an assembly. Disconnect overdrive band from anchor pins and
1990 Ford Bronco
remove band from case.

6. Remove forward clutch hub and No. 3 needle bearing as an assembly. Remove forward sun gear, No. 5
needle bearing, reverse sun gear and drive shell, and No. 4 needle bearing from case as an assembly.
7. Note position of center support snap ring tangs for installation reference. Remove snap ring. Using a
screwdriver, pry anti-clunk spring from between center support and case. Prior to removal, note position
of anti-clunk spring to ensure it is reinstalled correctly.
NOTE: Anti-clunk spring is not called out separately but is part of assembly No. 9
in Fig. 53 .
8. Remove center support and planetary carrier from case as an assembly. See Fig. 28 . Remove reverse
band from case. If direct clutch hub did not come out with planetary carrier, remove it from direct clutch.
CAUTION: If transmission is positioned with output shaft pointing up, DO NOT

allow shaft assembly to fall through case when governor is removed.
9. Remove retaining bolts and slide extension housing from transmission. Remove and discard housing-to-
case gasket. Remove retaining snap ring and slide governor assembly off output shaft. See Fig. 3 .
Remove governor drive ball from output shaft.
10. Remove output shaft, ring gear, and direct clutch as an assembly through front of case. Remove output
shaft No. 9 needle bearing from rear of case. Remove intermediate clutch pack from one-way clutch.
Remove reverse clutch assembly from forward clutch assembly. See Fig. 29 .
1990 Ford Bronco
Fig. 27: Removing Direct Drive Shaft

1990 Ford Bronco
Fig. 28: Removing Center Support & Planetary Carrier

1990 Ford Bronco
Fig. 29: Separating & Installing Clutch Packs

COMPONENT DISASSEMBLY & REASSEMBLY
GOVERNOR ASSEMBLY
Disassembly
1990 Ford Bronco
Remove retaining screws and separate counterweight from governor body. Remove cover screws and cover.
Remove plug, sleeve, and valve governor body. See Fig. 30 . Remove governor screen.
NOTE: Handle all parts carefully to avoid damage. Lubricate parts with ATF before
reassembly (petroleum jelly may be used on gaskets and thrust washers). Use
all NEW gaskets and seals.
Reassembly
1. If removed, install clip and spring on valve. Install valve into governor body. Install sleeve in body with
points outward.
2. Install plug in sleeve with knurled face inward. Install cover. Install screen in body with steel band (brass
colored) inward and tip of screen facing outward.
3. Position governor body on counterweight and install retaining screws. Tighten screws to specification.
See TORQUE SPECIFICATIONS . When correctly assembled, finished face of governor body should
be flush with face of counterweight.
Fig. 30: Exploded View of Governor Assembly

1990 Ford Bronco
INTERMEDIATE ONE-WAY CLUTCH
Disassembly & Reassembly
Remove clutch retaining ring and lift off clutch retaining plate. Remove clutch outer race by lifting on race
while turning counterclockwise. Carefully lift one-way clutch from inner race. See Fig. 31 . To reassemble,
reverse disassembly procedure.
NOTE: If a roller is damaged or lost, entire one-way clutch assembly must be replaced.
Fig. 31: Exploded View of Intermediate One-Way Clutch Assembly

OUTPUT SHAFT ASSEMBLY
Disassembly & Reassembly
1. Remove retaining ring and separate output hub assembly from ring gear. Remove direct clutch from ring
gear and No. 8 needle bearing from rear of direct clutch.
2. Remove 4 output shaft seal rings and hub-to-shaft retaining ring. Separate hub from output shaft. Remove
2 direct clutch seal rings from end of output shaft. See Fig. 32 . To reassemble, reverse disassembly
procedure.
1990 Ford Bronco
Fig. 32: Exploded View of Output Shaft Assembly

MANUAL & THROTTLE LINKAGE
Disassembly
1. Hold outer throttle lever stationary and remove retaining nut, lock washer, and throttle lever. Using a
small screwdriver, remove oil seal from outer manual lever counterbore.
CAUTION: Failure to hold outer throttle lever when removing retaining nut will
allow inner throttle lever to rotate against valve body surface, which
could result in damage to surface.
2. Using a sharp narrow screwdriver, remove manual shaft retaining pin from case. Hold inner manual lever
stationary and remove manual lever retaining nut with a 21 mm wrench. Remove throttle lever. Remove
inner throttle lever and T.V. torsion spring. See Fig. 4 .
3. Remove inner manual lever and parking pawl actuating rod as an assembly. Separate rod from lever if
necessary. Remove manual lever shaft seal from case using a seal puller.
Reassembly
To reassemble, reverse disassembly procedure. See Fig. 5 . Install new manual lever seal using Seal Installer
(T74P-77498-A). Before installing outer throttle lever, install NEW seal in outer manual lever using a 13 mm
1990 Ford Bronco
socket. Install seal with identification number facing forward.
DIRECT CLUTCH ASSEMBLY
Disassembly
1. Remove No. 7 direct clutch hub inner needle bearing and bearing support. Using a screwdriver, remove
clutch pack selective retaining snap ring and lift out clutch pack. See Fig. 33 .
2. Using a Compressor (T65L-77515-A), compress piston return springs and remove retaining snap ring.
Remove tool and lift spring retainer assembly and piston from clutch drum.
3. If necessary, piston can be removed by applying compressed air to lubrication hole in clutch drum. Note
position and direction of lip seals. Remove seals from drum and piston.
Inspection
1. Check piston check ball for freedom of movement. Check for leakage by turning piston upside down (flat
side up), allowing check ball to seat in piston.
2. Pour small quantity of solvent over check ball. If solvent drips past check ball, replace piston.
Reassembly
1. Using Seal Protector (T80L-77234-A), install inner seal on clutch drum hub with sealing lip facing down
into drum. Lubricate seals and seal protector with petroleum jelly prior to installation. Ensure inner seal is
positioned in groove. Install outer seal on piston with lip pointing away from spring posts.
2. Coat piston seals, clutch drum sealing area, and piston inner seal area with petroleum jelly. Install piston
into clutch drum using Seal Protector (T80L-77254-A) to prevent damaging seals.
3. Position piston spring and retainer assembly in clutch drum. Compress assembly and install retaining
snap ring. Install clutch pack into drum. Install pressure plate on top of clutch pack. Install clutch pack
selective retaining ring.
4. Using a feeler gauge, measure clearance between clutch pack retaining ring and pressure plate with
pressure plate held down. See DIRECT CLUTCH PLATE USAGE & CLEARANCE .
5. If clearance is not within specifications, selective snap rings are available in various sizes. See DIRECT
CLUTCH SNAP RINGS . Install correct size snap ring and recheck clearance.
6. To check clutch for proper operation, use compressed air at 30 psi (2.1 kg/cm2 ). See Fig. 34 . Clutch
should be heard and felt to apply smoothly and without leakage.
DIRECT CLUTCH PLATE USAGE & CLEARANCE

Engine Application Steel Plates Friction Plates Clearance In. (mm)
3.8L SC 6 6 .060-.088 (1.5 3-2.23)
All Others (1) 5 5 .050-.067 (1.27-1.70)
(1) Some models equipped with 4.6L or 5.0L engines may have 6 steel plates and 6 friction plates
with .060-.092" (1.53-2.34 mm) clearances.
DIRECT CLUTCH SNAP RINGS
1990 Ford Bronco
Part No. (1) Thickness
E0AZ7D483-A .052" (1.32 mm)

E0AZ7D483-B .066" (1.68 mm)
E0AZ7D483-C .080" (2.03 mm)
E0AZ7D483-D .094" (2.39 mm)
(1) Snap ring thicknesses have .002" (.05 mm) tolerance.
Fig. 33: Exploded View of Direct Clutch Assembly

1990 Ford Bronco
Fig. 34: Checking Direct Clutch Operation

FORWARD CLUTCH
Disassembly
1. Lift clutch hub and No. 3 needle bearing from forward clutch assembly. Using a screwdriver, pry clutch
pack selective retaining snap ring from drum. Remove clutch pack. See Fig. 35 .
2. Using Compressor Tool (T65L-77515-A), compress piston return spring and remove retaining snap ring.
Lift out retainer and return spring.
3. Remove clutch piston from drum. Note position of inner and outer piston seals, then remove seals. Ensure
check balls in piston are free.
Reassembly
1990 Ford Bronco
1. Lubricate and install inner and outer seals on piston with seal lips facing into clutch drum. Lubricate
piston seals and drum sealing area with petroleum jelly. Install piston into drum using Seal Protector
(T80L-77140-A) to prevent damaging seals.
2. Position return spring and retainer on piston. Compress return spring and install retaining snap ring.
Install clutch pack into clutch drum starting with waved plate. Install clutch pack retaining snap ring.
3. Using a feeler gauge, measure clearance between retaining snap ring and pressure plate with pressure
plate held down. Ensure clearance is .040-.071" (1.02-1.80 mm) for 3.8L EFI (4 clutches) engine
and .050-.089" (1.27-2.26 mm) for all others (5 clutches).
NOTE: If vehicle is not available at time of repair, application can be identified by

number of clutches. See FORWARD CLUTCH PLATE USAGE .
FORWARD CLUTCH PLATE USAGE

Application Steel Plates Friction Plates
3.8L EFI (1) 4 4
All Others (1) 5 5
(1) Plus one waved plate installed next to piston.
FORWARD & REVERSE CLUTCH SNAP RINGS

C8AZ7D483-C .062" (1.57 mm)

C7AZ7D483-A .078" (1.98 mm)
C8AZ7D483-B .090" (2.29 mm)
C8AZ7D483-A .104" (2.64 mm)
4. If clearance is not within specification, selective snap rings are available in various sizes. See
FORWARD & REVERSE CLUTCH SNAP RINGS . Install correct size snap ring and recheck
clearance.
5. With reassembly completed, use compressed air and check forward clutch operation. Clutch should be
heard and felt to apply smoothly and without leakage.
1990 Ford Bronco
Fig. 35: Exploded View of Forward Clutch Assembly

REVERSE CLUTCH
Disassembly
1. Remove No. 2 needle bearing. Using a screwdriver, pry clutch pack retaining snap ring from clutch drum.
Lift out clutch pack. See Fig. 36 .
2. Compress return spring and remove waved snap ring. Remove return spring and thrust ring. Remove
piston from drum. Remove seals from piston.
3. It may be necessary to apply compressed air to clutch drum lubrication hole to remove piston. Block
remaining hole with finger.
Reassembly
1. Prior to reassembly, ensure check ball in inner piston seal is free. Install NEW oil seal on piston. Coat
seals and sealing surface in clutch drum with petroleum jelly.
2. Install piston into clutch drum using Inner and Outer Seal Protectors (T80L-77403-B and A) to prevent
damaging seals. Seals used on reverse clutch piston are square cut; direction of installation is not
important.
3. Install thrust ring and return spring. Compress return spring and install waved snap ring with points
facing downward. Install apply plate into clutch drum with dished side facing piston. Install clutch pack
and retaining snap ring.
4. Using a feeler gauge, measure clearance between clutch pack snap ring and pressure plate while pushing
down on pressure plate. Ensure clearance is .030-.056" (.76-1.42 mm) for 3.8L EFI engine (3 friction
plates) and .040-.075" (1.02-1.91 mm) for all other models (4 friction plates).
5. If clearance is not within specification, selective snap rings are available in various sizes. See
FORWARD & REVERSE CLUTCH SNAP RINGS . Install correct size snap ring and recheck
1990 Ford Bronco
clearance.
6. With reverse clutch reassembly completed, check clutch operation using compressed air. Ensure clutch is
heard and felt to apply smoothly and without leakage. Install No. 2 thrust washer or No. 2 needle bearing.
Fig. 36: Exploded View of Reverse Clutch Assembly

CENTER SUPPORT & PLANETARY ONE-WAY CLUTCH
NOTE: If a roller from planetary one-way clutch is lost or damaged, entire one-way
clutch assembly must be replaced.
Disassembly
Remove center support from planetary carrier by lifting up on center support while rotating it counterclockwise.
Carefully remove planetary one-way clutch from planetary assembly. See Fig. 37 .
Reassembly
If necessary, assemble one-way clutch. See Fig. 2 . Lubricate clutch races and clutch assembly with petroleum
jelly to aid in assembly. Install one-way clutch in planetary carrier. Install center support into one-way clutch by
rotating center support counterclockwise.
1990 Ford Bronco
Fig. 37: Exploded View of Center Support & Planetary Assembly

Fig. 38: Assembling Planetary One-Way Clutch

SUN GEAR & DRIVING SHELL
1990 Ford Bronco
Disassembly
Remove No. 4 needle bearing from driving shell. Remove forward sun gear and No. 5 needle bearing from
shell. Remove No. 5 needle bearing from forward sun gear. See Fig. 39 .
Reassembly
Sun gear and driving shell will be reassembled as part of TRANSMISSION REASSEMBLY .
Fig. 39: Exploded View of Sun Gear & Drive Shell.

OIL PUMP & INTERMEDIATE CLUTCH PISTON
Disassembly
1. Lift No. 1 thrust washer from stator support. Remove 4 seal rings from stator support. Remove pump
body-to-case seal and discard. See Fig. 40 .
2. Remove spring retainer assembly by carefully dislodging the tabs. Lift intermediate clutch piston from
pump assembly. Remove retaining bolts and separate stator support from pump body. Remove drive and
driven gears from pump body.
NOTE: Reverse clutch seal rings on stator support are larger than forward clutch seal
rings.
Reassembly
1990 Ford Bronco
1. Install drive gear and driven gear into pump body with chamfer on both gears facing into pump body.
Position stator support on pump body. Install and tighten retaining bolts to specification. See TORQUE
SPECIFICATIONS . Install pump body-to-case seal around outer diameter of pump body.
2. Install NEW seals on intermediate clutch piston. Seal lips point away from spring posts. Coat piston seal
and pump body sealing area with petroleum jelly. Use Seal Protector (T80L-77005-A) and install piston
in pump body, ensuring piston bleed hole is located at 12 o'clock position (toward top of transmission
case).
3. Snap spring retainer assembly into place on pump body using even pressure. Install seal rings on stator
support. The 2 larger rings are installed closest to pump.
Fig. 40: Exploded View of Oil Pump & Intermediate Clutch

ACCUMULATOR & SERVOS
2-3 Accumulator
Install NEW seals on accumulator piston. Ensure diagonal cuts on seals are properly aligned. See Fig. 41 .
Low-Reverse Servo
1990 Ford Bronco
Inspect sealing edge on both servo cover and piston. Replace cover or piston, if necessary. Ensure servo piston
rod length is same as the one removed. See Fig. 41 .
Overdrive Servo
Separate piston from servo cover. Install NEW seals on piston and cover. Lubricate and assemble piston to
cover. See Fig. 41 .
1990 Ford Bronco
Fig. 41: Exploded View of Accumulator & Servo Assemblies

VALVE BODY ASSEMBLY
1990 Ford Bronco
NOTE: As valves are removed from each valve body bore, place individual parts in
correct order and in relative position to valve body for reassembly reference.
Tag all springs as they are removed for reassembly reference.
Disassembly
1. Remove and discard valve body gasket. Remove retaining bolts. Remove separator plate, reinforcement
plates, and separator plate gasket. Discard gasket.
2. Remove 2 relief valves and 7 check balls from valve body. Note location of Orange check ball. Orange
check ball is NOT interchangeable with 6 Black check balls. See Fig. 42 .
3. Remove retaining plates, valves and springs. Keep all valves and springs in original order for reassembly
reference. See Fig. 44 .
Fig. 42: Locating Check Balls in Valve Body

1990 Ford Bronco
Fig. 43: Exploded Views of Valve Body Components

Cleaning & Inspection
1. Clean all parts thoroughly in clean solvent, and blow dry with compressed air. Inspect all valves and plug
bores for scoring. Check all fluid passages for obstructions.
2. Inspect all mating surfaces, plugs, and valves for burrs and scoring. If necessary, use crocus cloth to
polish valves and plugs.
3. Inspect all springs for distortion. Check all valves and plugs for free movement in their respective bores.
Valves and plugs, when dry, must fall free of their own weight within their respective bores.
1990 Ford Bronco
CAUTION: Avoid rounding off sharp edges of valves and plugs with crocus cloth.
These edges perform a cleaning action.
Reassembly
1. Install all valves into their respective bores using illustrations as guide. Ensure chamfered stem of throttle
control valve faces throttle plunger. Retainer plate used for 2-3 capacity modulator valve is thicker and
longer than other retainer plates. Ensure notch in plugs face bottom of bore.
2. The 1-2 accumulator valve and valve body diameters are not the same for all models. The 1-2
accumulator valve bore plug "O" ring must face outside of valve body. To install Overdrive servo valve
bore plug, turn retaining plate into plug slot.
3. Install valve body check balls. See Fig. 42 . Ensure Orange check ball is correctly installed. This check
ball is larger than others and is not interchangeable. Install pressure relief valves and springs. See Fig.
43 .
4. Install Alignment Pins (T80L-77100-A) into holes. See Fig. 45 . These 2 holes are smaller than other bolt
holes to assure proper alignment of gasket and separator plate with valve body. These 2 holes also align
valve body gasket and valve body assembly with case.
5. Using a NEW separator plate gasket, slide plate and gasket over alignment pins. Position 3 reinforcement
plates and loosely install retaining bolts. See Fig. 43 .
6. Loosely install detent spring guide bolt. Detent spring guide bolt is same length as short valve body-to-
case retaining bolts. Starting at center (large) reinforcement plate and working outward, tighten retaining
bolts to specification. See TORQUE SPECIFICATIONS . Remove alignment pins.
Fig. 44: Installing Pressure Relief Valves

1990 Ford Bronco
Fig. 45: Identifying Valve Body Plates

REASSEMBLY
needle bearing locations. Lubricate all parts with ATF. Use petroleum jelly on
gaskets, thrust washers, and needle bearings to retain in place. Use NEW
gaskets and seals.
TRANSMISSION
Initial Reassembly
1990 Ford Bronco
1. Install No. 9 output shaft needle bearing in transmission case. Install bearing support, No. 7 needle
bearing and direct clutch hub in direct clutch assembly. Assemble output shaft hub to output shaft and
install retaining snap ring.
2. Place No. 8 needle bearing on rear of direct clutch drum. Slide output shaft into direct clutch drum.
Attach output shaft hub to ring gear with retaining ring. Install output shaft, ring gear, and direct clutch
assembly into transmission case. See Fig. 46 .
3. Position governor drive ball in pocket on output shaft. Slide governor assembly onto output shaft with
cover and attaching screws facing toward front of case. Ensure governor body is flush with
counterweight. Install governor retaining snap ring.
4. Install low-reverse band into transmission case and ensure band is seated on anchor pins. When properly
installed, center of band actuating rod seat can be seen through servo piston bore.
5. Install center support and planetary assembly into case. See Fig. 47 . If necessary, rotate output shaft to
align planet carrier splines with direct clutch hub splines. Install center support anti-clunk spring using a
hammer handle or wooden dowel. Spring tabs must face out.
NOTE: Center support and planet carrier cannot be installed unless notch cut in center
support is aligned with overdrive band anchor pin. See Fig. 47 .
1990 Ford Bronco
Fig. 46: Installing Direct Clutch Assembly

1990 Ford Bronco
Fig. 47: Aligning Center Support Notch

Low-Reverse Servo Pin Selection
1. Install center support retaining ring. Determine correct length of low-reverse servo pin to use. Lubricate
and install servo piston and return spring. DO NOT install cover or retaining ring. Install Servo Selector
Gauge (T80L-77030-A) into servo bore.
2. Tighten band apply bolt on tool to 50 INCH lbs. (5.6 N.m). Attach dial indicator. Position indicator stem
on flat portion of servo piston. Zero dial indicator. See Fig. 48 .
3. Thread bolt out of selector tool until piston stops against bottom of tool. Read amount of piston travel on
dial indicator. If travel is .112-.237" (2.845-6.020 mm), correct servo pin is installed. If travel is not
within specification, selective pistons are available. See LOW-REVERSE SERVO PISTONS .
1990 Ford Bronco
Fig. 48: Measuring Low-Reverse Servo Pin Travel

LOW-REVERSE SERVO PISTONS

No. of
Part No. Assembly Length Grooves
E0AZ7D189-A 2.936" (74.57 mm) 1
E0AZ7D189-B 2.989" (75.92 mm) 2
E0AZ7D189-C 3.043" (77.29 mm) 3
4. Length is measured from base of piston to end of rod. Select servo rod to bring servo travel within
specification. Remove selector tool and dial indicator.
5. Install selected low-reverse servo piston. Install servo cover and cover retaining snap ring.
Final Reassembly
1. Install reverse clutch on forward clutch. See Fig. 29 . Ensure No. 2 needle bearing is in position in reverse
clutch. Install No. 3 needle bearing and forward clutch hub in forward clutch. Position No. 4 needle
1990 Ford Bronco
bearing on forward clutch hub.

2. Install drive shell over clutch assemblies. Install No. 5 needle bearing and forward sun gear on drive shell.
Install complete assembly into case, rotating output shaft to aid in engaging sun gear with planetary gears.
See Fig. 49 .
3. Install overdrive band into case and around drive shell assembly. Ensure band anchor is properly
positioned on anchor pin. Using a screwdriver to hold overdrive band in position, lubricate and install
overdrive servo.
4. With overdrive servo installed, inspect band and apply pin for proper position and engagement. If band
anchor and apply pin are not properly engaged, remove servo and re-position band as necessary.
5. Install intermediate clutch pack pressure plate, clutch pack (starting with a friction plate and alternating
steel and friction plates) and selective steel plate in this order. Measure intermediate clutch clearance.
6. Intermediate clutch clearance is measured using a depth micrometer and End Play Checking Bar (T80L-
77003-A). Set end play tool across pump case mounting surface. Locate micrometer end play bar and
read depth. See Fig. 50 .
NOTE: A downward pressure must be applied to clutch pack while measuring

intermediate clutch clearance.
1990 Ford Bronco
Fig. 49: Installing Drive Shell & Clutch Assemblies

1990 Ford Bronco
Fig. 50: Measuring Intermediate Clutch Clearance

7. Check depth again with micrometer 180 degrees opposite from previous measurement. Ensure depth at
intermediate clutch selective steel plate is 1.634-1.646" (41.504-41.808 mm). Ensure average of the 2
measurements is within this range.
8. If intermediate clutch clearance (depth) is not within tolerance, see INTERMEDIATE CLUTCH
SELECTIVE STEEL PLATES . Install correct size plate and recheck clearance.
INTERMEDIATE CLUTCH PLATE USAGE

Application Steel Plates Friction Plates
All 3 3
INTERMEDIATE CLUTCH SELECTIVE STEEL PLATES

E0AP7F220-A1A .069 (1.75 mm)

E0AP7F220-A2A .079 (2.01 mm)
E0AP7F220-A3A .089 (2.26 mm)
E0AP7F220-A4A .099 (2.51 mm)
1990 Ford Bronco
9. Check transmission end play by locating depth micrometer on End Play Checking Bar (T80L-77003-A).
Ensure depth is measured at reverse clutch drum thrust face. See Fig. 51 . Standard end play is .004-
.044" (.101-1.11 mm).
10. Check end play 180 degrees opposite end of reverse clutch drum thrust face to determine average depth.
Thrust washer controlling transmission end play is located on stator support which is attached to back of
pump housing.
11. Transmission end play can be adjusted using one of selective thrust washers available for service. After
measuring depth, select required thrust washer. See END PLAY THRUST WASHER SELECTION .
1990 Ford Bronco
Fig. 51: Measuring Transmission End Play

END PLAY THRUST WASHER SELECTION

Measured Depth In. Washer Thickness
(mm) In. (mm) Color Code
1.483-1.500 (37.67- .050-.054 (1.27-1.37) Green
38.10)
1.501-1.517 (38.13- .068-.072 (1.73-1.83) Yellow
38.53)
1.518-1.534 (38.56- .085-.089 (2.16-2.26) Natural
38.96)
1.535-1.551 (38.99- .102-.106 (2.59-2.69) Red
39.40)
1.552-1.568 (39.42- .119-.123 (3.02-3.12) Blue
39.83)
12. Install selected transmission end play thrust washer on stator support. Use petroleum jelly to hold it in
place. Install pump alignment dowel, made by cutting the head from a M8 x 1.25 bolt, into pump
mounting bolt hole at 6 o'clock position.
13. Install new pump gasket into case. Install pump assembly into case using 2 slide hammers to lower pump
into position. Remove alignment dowel. Coat all pump-to-case bolts with Loctite and install in case.
14. Alternately tighten bolts a few turns at a time to draw pump into case. Tighten bolts to specification. See
TORQUE SPECIFICATIONS . Install 2-3 accumulator assembly. Install 2 valve body Alignment Pins
(T8OL-77100-A) into valve body.
15. Install valve body gasket and valve body assembly over pins. Ensure manual and throttle levers are
properly positioned before installing valve body retaining bolts.
NOTE: Two different length valve body retaining bolts are used. Longer bolts are
used at 4 front, 1 center and 3 rear locations.
16. Loosely install valve body retaining bolts. Starting at center and working outward, tighten bolts. Remove
alignment pins and install bolts. Install detent spring and roller assembly and tighten bolts to
specification. See TORQUE SPECIFICATIONS .
17. Position T.V. lever torsion spring against separator plate "V" notch. This spring pushes the throttle lever
in direction of wide open throttle.
18. Install filter grommet, new filter gasket, and filter on valve body. Install filter attaching bolts and tighten.
Position new pan gasket on case and install oil pan. Clean mating surface on transmission and extension
housing. Position new gasket on transmission. Slide extension housing into place.
19. Clean bolts and case holes for 2 bottom bolts and lower right hand corner bolt (as viewed from rear of
extension housing). Coat bolts with Teflon tape and install. Install remaining bolts and tighten to
specification.
20. Slide direct drive shaft into turbine input shaft. Install torque converter. Ensure pump is fully seated.
1990 Ford Bronco
Fig. 52: Locating Needle & Thrust Bearings

1990 Ford Bronco
Fig. 53: Exploded View of AOD Transmission

TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS
Application Ft Lbs. (N.m)
Converter-To-Flywheel Bolt 20-34 (27-46)
Converter Housing Cover-To-Converter Housing 12-16 (16-22)
Converter Plug-To-Converter 8-28 (11-38)
Cooler Line-To-Case 18-23 (24-31)
Extension-To-Case Bolt 16-20 (22-27)
Inner Manual Lever-To-Shaft Nut 19-27 (26-37)
Outer Throttle Lever-To-Shaft Nut 12-16 (16-22)
Pump-To-Case Bolt 16-20 (22-27)
1990 Ford Bronco
Stator Support-To-Pump Bolt 12-16 (16-22)

Stator Support-To-Pump Bolt 12-16 (16-22)
Transmission-To-Engine Bolt 40-50 (54-68)
INCH lbs. (N.m)
Cover-To-Governor Body Bolt 20-30 (2.3-3.4)
Detent Spring Attaching Bolt 80-120 (9-14)
Filter-To-Valve Body 80-120 (9-14)
Governor Body-To-Counterweight Bolt 50-60 (6-7)
Neutral Start Switch-To-Case 95-130 (11-15)
Oil Pan-To-Case Bolt 72-120 (8-14)
Pressure Plug-To-Case 72-144 (8-16)
Reinforcing Plate-To-Valve Body Bolt 80-120 (9-14)
Separator Plate-To-Valve Body Bolt 80-100 (9-11)
Valve Body-To-Case Bolt 80-100 (9-11)

Application: 1990 Ford Bronco 1990 Ford Bronco

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Application: 1990 Ford Bronco 1990 Ford Bronco

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Application: 1990 Ford Bronco 1990 Ford Bronco

Uploaded by

Copyright:

Available Formats

1990 Ford Bronco

1983-92 AUTOMATIC TRANSMISSIONS Ford AOD Overhaul

1983-92 AUTOMATIC TRANSMISSIONS

Ford AOD Overhaul

jueves, 26 de enero de 2023 12:04:48

Fig. 1: Service Identification Tag

LUBRICATION & ADJUSTMENTS

VALVE BODY ASSEMBLY

OVERDRIVE SERVO ASSEMBLY

LOW-REVERSE SERVO ASSEMBLY

2-3 ACCUMULATOR PISTON

Fig. 2: Identifying Accumulator & Servo Locations

Courtesy of FORD MOTOR CO.

EXTENSION HOUSING BUSHING & REAR OIL SEAL

Fig. 3: Removing Governor Assembly

INTERNAL & EXTERNAL SHIFT LINKAGE

Fig. 4: Identifying Manual & Throttle Linkage Components

Fig. 5: Exploded View of Manual & Throttle Linkage

NEUTRAL SAFETY SWITCH

See appropriate TRANSMISSION SERVICING - A/T article in TRANSMISSION SERVICING.

Slow Initial Engagement

Plugged filter or low main control pressure.

Rough Initial Engagement

Delayed Or No Forward Engagement, Reverse Okay

Delayed Or No Reverse Engagement, Forward Okay

Fig. 6: Cross-Sectional View of AOD Transmission

Delayed Or No Reverse Engagement And/Or No Engine Braking In Manual Low

No Engine Braking In Manual 2nd

Forward Engagement Slips, Shudders Or Chatters On Engagement

Reverse Engagement Slips, Shudders Or Chatters On Engagement

Starts Up In 2nd Or 3rd

Incorrect Shift Points, Harsh Or No Upshift

Early, Mushy, Soft Or Slipping Upshift

Transmission Clunk Or Squawk During Upshift

Transmission Noisy (Valve Resonance)

Harsh Initial Engagement Into Drive

Delayed Reverse Engagement

Slips & Chatters When Hot, Delayed Drive & Reverse

Worn pump. Pressure regulator valve sticking when hot.

No Forward After A Stop

The 3-4 shift valve stuck in upshifted position.

No 2nd, 4th Or Reverse

Broken weld on sun gear shell.

No 2nd Or 4th, Reverse Okay

Stuck 1-2 shift valve.

Clacking Noise Or Squawk, Intermediate Buck On Deceleration

Neutral Condition On 3-4 Upshift

Bucking On Deceleration & Kills Engine When Stopping

Governor valve in high gear position.

Chatters Or Bucks On Acceleration Or Deceleration In 4th Gear

Engine performance problem (EGR, fuel system, etc.).

No 3-4 Upshift Until 50 MPH, Or Until Accelerator Pedal Is Released Slightly

Harsh 4-3 Or 4-2 Downshift

Bearing Whine In All Gear Positions Except 3rd & 4th

CLUTCH & BAND APPLICATION CHART

CLUTCH & BAND APPLICATION CHART

2nd Intermediate Clutch, Forward Clutch &

Fig. 7: Identifying Control Pressure Taps