VX-261 Uhf SM Ec128u90c

Vertex Standard LMR, Inc.
UHF FM Transceiver
©2015 Vertex Standard LMR, Inc.
VX-261 EC128U90C
Service Manual
Introduction
This manual provides the technical information necessary for servicing the VX-261 UHF FM
Transceiver.
Servicing this equipment requires expertise in handing surface-mount chip components. At-
tempts by non-qualified persons to service this equipment may result in permanent damage not
covered by the warranty, and may be illegal in some countries.
Two PCB layout diagrams are provided for each double-sided board in this transceiver. Each side
of the board is referred to by the type of the majority of components installed on that side (“Side
A” or “Side B”). In most cases one side has only chip components (surface-mount devices), and
the other has either a mixture of both chip and leaded components (trimmers, coils, electrolytic
capacitors, ICs, etc.), or leaded components only.
As described in the pages to follow, the advanced microprocessor design of the VX-261 Trans-
ceiver allows a complete alignment of this transceiver to be performed without opening the case
of the radio; all adjustments can be performed from the front panel, using the “Alignment Mode”
menu.
While we believe the information in this manual to be correct, Vertex Standard assumes no li-
ability for damage that may occur as a result of typographical or other errors that may be present.
Your cooperation in pointing out any inconsistencies in the technical information would be ap-
preciated.
Important Note
This transceiver is assembled using Pb (lead) free solder, based on the RoHS specification.
Only lead-free solder (Alloy Composition: Sn-3.0Ag-0.5Cu) should be used for repairs performed on this apparatus.
The solder stated above utilizes the alloy composition required for compliance with the lead-free specification, and
any solder with the above alloy composition may be used.
Contents
Specifications................................................................................................................................................................. 2
Exploded View & Miscellaneous Parts........................................................................................................................ 4
Parts List........................................................................................................................................................................ 5
Block Diagram............................................................................................................................................................... 6
Circuit Description........................................................................................................................................................ 7
Alignment....................................................................................................................................................................... 9
Cloning......................................................................................................................................................................... 16
Main Unit Circuit Diagram (Type “G7”: FR027720D)........................................................................................... 17
Main-2 Unit Circuit Diagram (Type “G6”: FR027830A). ...................................................................................... 18
VX-261 UHF FM Transceiver Service Manual 1

Specifications: USA (NA) & Except EIA (CE)
General
Frequency range: 403-470 MHz (Type “G6”)
450-520 MHz (Type “G7”) (USA Model: 450-512 MHz)
Channel: 16 Channels
Power Supply Voltage: 7.4 V DC ± 10%
Current Consumption: <2.0 A (5 W TX)
Channel Spacing: 12.5 / 25 kHz (USA Model: 12.5 kHz)
PLL Steps: 5 / 6.25 kHz
IP Rating: IP55
Operating Temperature Range: –22 °F to +140 °F (–30 °C to +60 °C)
Charging Temperature Range: +32 °F to +113 °F (0 °C to +45 °C)
Frequency Stability: ±2.5 ppm
RF Input-Output: 50 Ohm (unbalanced)
Dimension (H x W x D): 2.3 x 4.3 x 1.3 inches (58.4 x 109 x 32.3 mm) (with FNB-V133LI-UNI)
2.3 x 4.3 x 1.6 inches (58.4 x 109 x 39.9 mm) (with FNB-V134LI-UNI)
Weight (Approx.): 9.9 oz (281 g) (with FNB-V133LI-UNI, Antenna, Belt Clip)
11.6 oz (330 g) (with FNB-V134LI-UNI, Antenna, Belt Clip)
Receiver (Measured by TIA/EIA-603)

Circuit Type: Double Conversion Super-heterodyne
Sensitivity (12 dB SINAD): 0.25 µV
Adjacent Channel Selectivity: 65 / 60 dB (W/N)
Hum and Noise: 45 / 40 dB (W/N)
Intermodulation: 65 dB
Spurious Image Rejection: 70 dB
Conducted Spurious: –57 dBm
Audio output: 700 mW (intemal @ 16 Ohm 5% THD)
500 mW (extemal @ 4 Ohm 5% THD)
Transmitter (Measured by TIA/EIA-603)

Output Power: 5/1W
Modulation: 16K0F3E / 11K0F3E
Maximum Deviation: ±5.0 kHz / ±2.5 kHz
Conducted Spurious Emissions: 70 dB below carrier
FM Hum & Noise: 45 / 40 dB (W/N)
Audio Distortion: <5% @ 1 kHz
Specifications subject to change without notice or obligation.

Specifications: EIA (CE)
General
Frequency range: 403-470 MHz (Type “G6”)
450-520 MHz (Type “G7”)
Channel: 16 Channels
Power Supply Voltage: 7.4 V DC ± 10%
Current Consumption: <2.0 A (5 W TX)
Channel Spacing: 12.5 / 20 / 25 kHz
PLL Steps: 5 / 6.25 kHz
IP Rating: IP55
Operating Temperature Range: –30 °C to +60 °C
Charging Temperature Range: 0 °C to +45 °C
Frequency Stability: ±2.5 ppm
RF Input-Output: 50 Ohm (unbalanced)
Dimension (H x W x D): 58.4 x 109 x 32.3 mm (with FNB-V133LI-UNI)
58.4 x 109 x 39.9 mm (with FNB-V134LI-UNI)
Weight (Approx.): 281 g (with FNB-V133LI-UNI, Antenna, Belt Clip)
330 g (with FNB-V134LI-UNI, Antenna, Belt Clip)
Receiver (Measured by ETC 300 086)

Circuit Type: Double Conversion Super-heterodyne
Sensitivity (20 dB SINAD): –2 dBµV
Adjacent Channel Selectivity: 65 / 60 dB (W/N)
Hum and Noise: 45 / 40 dB (W/N)
Intermodulation: 65 dB
Spurious Image Rejection: 70 dB
Conducted Spurious: –57 dBm @< = 1 GHz, –47 dBm @> 1 GHz
Audio output: 700 mW (intemal @ 16 Ohm 5% THD)
500 mW (extemal @ 4 Ohm 5% THD)
Transmitter (Measured by ETC 300 086)

Output Power: 5/1W
Modulation: 16K0F3E / 14K0F3E / 11K0F3E
Maximum Deviation: ±5.0 kHz / ±4.0 kHz / ±2.5 kHz
Conducted Spurious Emissions: –36 dBm @< = 1 GHz, –30 dBm @> 1 GHz
FM Hum & Noise: 45 / 40 dB (W/N)
Audio Distortion: <5% @ 1 kHz
Specifications subject to change without notice or obligation.

Exploded View & Miscellaneous Parts
CB6642000 CB6987000 (TYPE “G7”)

MIC/SP CAP ASSY CB6994000 (TYPE “G6”)
FRONT CASE ASSY
RA1612700
KNOB (VOL)
RA1612800
KNOB (FREQ)

RA125020A
SHIELD CASE COVER (FET) CB6988000 (TYPE “G7”)
MAIN UNIT ASSY
CB6989000 (TYPE “G6”)
MAIN-2 UNIT ASSY
RA157250A (x 2 pcs)
RING NUT
RA1458000
RUBBER BOOTS
RA037690B
SHEET (6x6)
FRONT CASE ASSY (Component) RA1612600

RUBBER PACKING
FRONT CASE (NON KEY)
NAME PLATE
MODEL LABEL (VX-261)
RUBBER (PTT)
FLAME (PTT) CB6984000
RUBBER (SIDE) CHASSIS ASSY
LATCH NAIL
LATCH PLATE
COIL SPRING (2.2x12x0.25) (x2 pcs)
INDICATOR
SPEAKER
SP NET
WIRE ASSY (BLK) RA0292100
WIRE ASSY (YEL) SHEET (MICROTEX C010)
SHIELD SHEET (TYPE “G7” only)
SHEET (MICROTEX 8x4)
PAN HEAD SCREW (M2x3BUS #2)

MIC/SP CAP ASSY (Component)
CAP (MIC/SP)
O RING (CAP) AAJ67X001
O RING (0.8x2.2) (x2 pcs) Li-Ion BATTERY PACK (FNB-V133LI-UNI)
or RA1614100
BIND HEAD SCREW (M2.6x6B) (x2 pcs) AAJ68X001 CAUTION LABEL
Li-Ion BATTERY PACK (FNB-V134LI-UNI)
CHASSIS ASSY (Component)
CHASSIS
CONNECTOR (5MAF11S-T02)
RUBBER PACKING
RUBBER BOOTS
SHEET (6x6)
SHEET (MICROTEX C010)
CAUTION LABEL
BIND HEAD TAPTITE-B (2x10) (x2 pcs)
MAIN UNIT (Component)

Printed Circuit Board with Components
HOLDER RUBBER (MIC) AAH12X101
SPONGE RUBBER (LIGHT GUIDE) BELT CLIP (CLIP-20)
SHIELD CASE COVER (FET)
RING NUT (x2 pcs)
PAN HEAD TAPTITE-B (M2x5) (x13 pcs)
REF. VXSTD P/N DESCRIPTION QTY.

U24110001 BIND HEAD TAPTITE-B 2X10 2
U44105001 PAN HEAD TAPTITE-B M2X5 13
Non-designated parts are available only as part of a designated assembly.

Parts List
REF. DESCRIPTION VALUE MFR’s DESIG VXSTD P/N
FRONT CASE ASSY CB6987000: TYPE “G7”
CB6994000: TYPE “G6”
MIC/SP CAP ASSY CB6642000
CHASSIS ASSY CB6984000
RUBBER PACKING RA1612600
RUBBER BOOTS RA1458000
SHEET (6x6) RA037690B
SHEET (MICROTEX C010) RA0292100
CAUTION LABEL RA1614100
BIND HEAD TAPTITE-B (x2 pcs) (2x10) U24110001
MECHANICAL PARTS
KNOB (VOL) RA1612700
KNOB (FREQ) RA1612800
MAIN UNIT ASSY CB6988000: TYPE “G7”

CD1001 CERAMIC DISC JTBM450CX24-A H7901530A
CF1001 CERAMIC FILTER LTM450GW-A H3900573A
CF1002 CERAMIC FILTER LTM450EW-A H3900574A
F 1001 CHIP FUSE 3.15A, 36 V FHC16 322ADTP Q0000118
MC1001 MIC. ELEMENT PF0-1055P M3290045
Q 1012 FET RQA0011DNS#G0 G3070507
S 1001 TACT SWITCH EVQPUB02K N5090167
S 1004 ROTARY SWITCH TP7LBJT16 RY-10487 N0190199
TH1001 THERMISTOR TH05 4B473FR G9090150
VR1001 POT. TP7LBRN1 B503 RY-10489 J60800323
X 1001 XTAL 11.0592MHz EXS00A-CG04670 H0103439
X 1002 XTAL OSC 16.8MHz HKE3449A 16.8MHZ H9501513
XF1001 XTAL FILTER MFT50.85P 50.85MHZ H1102361
SHIELD CASE COVER (FET) RA125020A
RING NUT (x2 pcs) RA157250A
PAN HEAD TAPTITE-B (x13 pcs) (M2X5) U44105001
MAIN-2 UNIT ASSY CB6989000: TYPE “G6”

CD2001 CERAMIC DISC JTBM450CX24-A H7901530A
CF2001 CERAMIC FILTER LTM450GW-A H3900573A
CF2002 CERAMIC FILTER LTM450EW-A H3900574A
F 2001 CHIP FUSE 3.15A, 36 V FHC16 322ADTP Q0000118
MC2001 MIC. ELEMENT PF0-1055P M3290045
Q 2012 FET RQA0011DNS#G0 G3070507
S 2004 ROTARY SWITCH TP7LBJT16 RY-10487 N0190199
TH2001 THERMISTOR TH05 4B473FR G9090150
VR2001 POT. TP7LBRN1 B503 RY-10489 J60800323
X 2001 XTAL 11.0592MHz EXS00A-CG04670 H0103439
X 2002 XTAL OSC 16.8MHz HKE3449A 16.8MHZ H9501513
XF2001 XTAL FILTER MFT50.85P 50.85MHZ H1102361
SHIELD CASE COVER (FET) RA125020A
RING NUT (x2 pcs) RA157250A
PAN HEAD TAPTITE-B (x13 pcs) (M2X5) U44105001
When replace a chip fuse,

use the part of the same type and value.

Block Diagram

Circuit Description
1. Receiver System 1-4. Audio amplifier
The detected signal from Qx040 (AA32416) is supplied
1-1. Front-end RF amplifier
to the AF adder Qx045-1 (NJM12902V) through the TX/
Incoming RF signal from the antenna passes through the
RX switch Qx057-2 (SN74LV4066A), high-pass filter
low-pass filter, antenna switching diode Dx004 and Dx005
Qx045-2 (NJM12902V), and mute switch Qx057-4
(both 1SS390), high-pass filter and removed undesired
(SN74LV4066A).
frequencies by varactor tuned band-pass filter Dx007 and
Dx009 (both 1SV305). The audio signal from Qx045-1 (NJM12902V) is sup-
plied to the audio amplifier Qx008 (TDA2822L) through
The filtered RF signal is amplified by Qx015 (BFS505)
the AF volume potentiometer (VRx001). As a result, the
and then passes through another varactor tuned band-pass
audio signal provides up to 700 mW (@16-ohm BTL) for
filter Dx013 and Dx014 (both 1SV305) to remove the
internal speaker or up to 500 mW (@4-ohm OTL) for ex-
undesired frequencies, and then applied to the 1st mixer
ternal speaker.
Qx020 (3SK293).
1-2. First Mixer 1-5. Squelch Circuit

There are 16 levels of squelch setting from “0” to “15”.
The RF signal is mixed with the 1st local signal be-
The level “0” means open the squelch. The level “1”
tween 352.15 and 419.15 MHz (Type “G6”) or 399.15
means the threshold setting level and level “14” means
and 469.15 MHz (Type “G7”) in the 1st mixer Qx020
tight squelch. From level “2” to level “13” is established
(3SK293), to produce 50.85 MHz 1st IF signal.
in the middle of threshold and tight. The level “15” be-
The 1st local signal is generated by the VCO, which comes setting of carrier squelch.
consists of Qx029 (CPH3910), varactor diodes Dx021,
1-5-1. Noise Squelch
Dx022, Dx023, and Dx025 (all 1SV323). The 1st lo-
cal signal is supplied to the 1st mixer Qx020 (3SK293) The noise squelch circuit is consisted of the band-path fil-
ter, noise amplifier Qx047 (2SC4617), and noise detector
through the buffer amplifier Qx021 and Qx026 (both
Dx035 (DA221).
2SC5010).
When a carrier isn’t received, the noise ingredient which
1-3. IF Amplifier & Demodulator
goes out of the demodulator section of Qx040 (AA32416)
The 1st IF signal passes through monolithic crystal filters
is amplified by noise amplifier Qx047 (2SC4617)
XFx001 (±7.5 kHz BW) to strip away all but the desired
through the band-path filter, and then is detected to DC
signal, and then supplied the buffer amplifier Qx035
voltage by Dx035 (DA221). The DC voltage is inputted
(2SC5226).
to pin 54 (A/D port) of the CPU Qx028 (R5F100LHDFB).
The amplified 1st IF signal is applied to the FM IF subsys- When a carrier is received, the DC voltage becomes low
tem IC Qx040 (AA32416) which contains the 2nd mixer, because the noise is compressed.
2nd local oscillator, limiter amplifier, noise amplifier, and
When the detected voltage to CPU is “High”, the CPU
RSSI amplifier.
stops the AF output of Qx013 (DTC144EE) by making to
The signal from reference oscillator Xx002 (16.8 MHz) “low” of the pin 39 of CPU.
becomes three times of frequencies in Qx040 (AA32416),
When the detection voltage to CPU is “low”, the CPU al-
it is mixed with the 1st IF signal and becomes 450 kHz.
lows the AF output of Q1013 (DTC144EE) by making to
The 2nd IF signal passes through the ceramic filter “High” of the pin 39 of CPU.
CFx001 (LTM450GW) or CFx002 (LTM450EW) to strip
1-5-2. Carrier Squelch
away unwanted mixer products, and is supplied to the
The detected RSSI voltage from pin 12 of Qx040
limiter amplifier in Qx040 (AA32416), which removes
(AA32416) supplied to pin 53 (A/D port) of Qx028
amplitude variations in the 450 kHz IF, before detection
(R5F100LHDFB). It is controls the AF output.
of the speech by the ceramic discriminator CDx001 (JT-
BM450CX24). The RSSI output voltage changes according to the signal
strength of carrier. The stronger signal makes the RSSI
Parts reference number is as follows voltage to be higher voltage. The process of the AF signal
Main Unit (Type “G7”: FR027720C): 1000 -1999 control is same as Noise Squelch. The shipping data is ad-
Main-2 Unit (Type “G6”: FR027830A): 2000 -2999 justed 3 dBµ (EMF) higher than squelch tight sensitivity.

Circuit Description
2. Transmitter System 3. PLL Frequency Synthesizer
2-1. MIC Amplifier 3-1. VCO (Voltage Controlled Oscillator)
The speech signal from internal microphone MCx001 While the radio is receiving, the RX VCO Qx029
or external microphone Jx003 is amplified by Qx044-2 (CPH3910) generates a programmed frequency between
(NJM12902V). 352.15 and 419.15 MHz (Type “G6”) or 399.15 and
469.15 MHz (Type “G7”) as 1st local signal.
The amplified speech signal from Qx044-2 (NJM12902V)
is supplied to pin 14 of Electric Volume IC Qx018 While the radio is transmitting, the TX VCO Qx037
(AK2330) which adjusts the microphone gain through (2SC4227) generates a frequency between 403 and 470
the TX/RX switch Qx057-2 (SN74LV4066A), high-pass MHz (Type “G6”) or 450 and 512 MHz (Type “G7”).
filter Qx045-2 (NJM12902V), and other TX/RX switch
The output from VCO is amplified by buffer amplifier
Qx057-3 (SN74LV4066A).
Qx026 and Qx021 (both 2SC5010). The buffered VCO
The adjusted speech signal is output from pin 15 of Qx018 is supplied to the 1st mixer Qx020 (3SK293) in case of
(AK2330), and then passed through the limiter ampli- the reception. In the transmission, the buffered VCO is
fier Qx044-1 (NJM12902V), low-pass filter Qx044-2/-3 supplied to other buffer amplifier Qx019 (2SK3077), and
(NJM12902V), and AF adder Qx052-3 (NJM12902V). then amplified more by Qx016 (RQA0004PXDQS) and
it is put into the final amplifier Qx012 (RQA0011DNS).
The processed speech signal from Qx052-3
(NJM12902V) is supplied to pin 22 of Electric Volume A portion of the buffered VCO is fed back to the PLL IC
IC Qx018 (AK2330) which adjusts the maximum devia- Qx046 (AK1541) to control the VCV voltage.
tion. The adjusted speech signal is amplified by Qx052-
2 (NJM12904R), and then is made FM modulation to
3-2. Varactor Control Voltage
The tuning voltage (VCV) of VCO is established the lock
transmit carrier by the modulator Dx019 (BB208) of
range of VCO by controlling the cathode of varactor di-
VCO Qx037 (2SC4227).
odes Dx021, Dx022, Dx023, and Dx025 (all 1SV323)
2-2. Drive and Final Amplifier Stages for receiving and Dx026 and Dx029 (both 1SV323) for
The modulated signal from the VCO Qx037 (2SC4227) transmitting.
is buffered by Qx026 (2SC5010). Then the signal is
buffered by Qx021 (2SC5010) and Qx019 (2SK3077)
3-3. PLL
The PLL IC Qx046 (AK1541) is consists of reference
for the driver amplifier Qx016 (RQA0004PXDQS). The
divider, main divider, phase detector, charge pumps, and
low-level transmit signal is then applied to Qx012 (RQA-
pulse swallow operation.
0011DNS) for final amplification up to 5 watts output
power. The reference frequency from TCXO Xx002 (16.8 MHz)
is inputted to pin 10 of PLL IC Qx046 (AK1541) and
The transmit signal then passes through the antenna
is divided by reference divider. On the other hand, the
switch Dx003 (RN142S) and is low-pass filtered to sup-
feedback signal of the VCO inputted to 17 pin of PLL IC
press away harmonic spurious radiation before delivery to
Qx046 (AK1541), and is divided with the dividing ratio
the antenna.
which becomes same frequency as the output of reference
2-3. Automatic Transmit Power Control divider.
The current detector Qx053-1 (NJM12902V) detects the
These two signals are compared by phase detector, and
current of the driver amplifier Qx016 (RQA0004PXDQS)
then phase difference pulse is generated. The phase dif-
and final amplifier Qx012 (RQA0011DNS), and converts
ference pulse is becomes a DC voltage through the charge
the current difference to the voltage difference.
pumps and LPF, and it controls the VCO.
The output from the current detector Qx053-1
The PLL serial data from CPU Qx028 (R5F100LHDFB)
(NJM12904R) is compared with the reference voltage
is sent with three lines of SDO (pin 5), SCK (pin 6) and
by Qx053-2 (NJM12904R). The output from Qx053-2
PSTB (pin 4).
(NJM12904R) controls the gate bias of the driver am-
plifier Qx016 (RQA0004PXDQS) and final amplifiers The lock condition of PLL is output from the UL (pin 7)
Qx012 (RQA0011DNS). terminal of the PLL IC Qx046 (AK1541). The UL termi-
nal becomes “High” at the lock condition, and becomes
The reference voltage changes into two levels (Transmit
“Low” at the unlock condition.
Power “High” and “Low”) controlled by the Electric Vol-
ume IC Qx018 (AK2330). The CPU Qx028 (R5F100LHDFB) is always watch-
ing over the UL condition, and when it becomes “Low”
Parts reference number is as follows unlocked condition, the CPU prohibits transmitting and
Main Unit (Type “G7”: FR027720C): 1000 -1999 receiving.
Main-2 Unit (Type “G6”: FR027830A): 2000 -2999

Alignment
Introduction Required Test Equipment
The VX-261 is carefully aligned at the factory for the  RF Signal Generator with calibrated output level at
specified performance across the frequency range speci- 600 MHz
fied for each version. Realignment should therefore not  Oscilloscope
be necessary except in the event of a component failure,  Deviation Meter (linear detector)
or altering version type. All component replacement and  In-line Wattmeter with 5 % accuracy at 600 MHz
service should be performed only by an authorized Vertex  50 Ohm RF Dummy Load with power rating 10 W at
Standard representative, or the warranty policy may be 600 MHz
void.  Regulated DC Power Supply (standard 7.5 V DC, 3 A)
 Frequency Counter with 0.2 ppm accuracy at 600
The following procedures cover the sometimes critical and
MHz
tedious adjustments that are not normally required once
 Audio Signal Generator
the transceiver has left the factory. However, if damage
 AC Voltmeter
occurs and some parts subsequently are replaced, realign-
 DC Voltmeter
ment may be required. If a sudden problem occurs during
 UHF Sampling Coupler
normal operation, it is likely due to component failure;
 IBM® PC/compatible Computer with Microsoft® Win-
realignment should not be done until after the faulty com-
dows® 2000, XP, Vista or Windows7
ponent has been replaced.
 Vertex Standard CE150 PC Programming Software
We recommend that servicing be performed only by au-  Vertex Standard FIF-12 USB Programming Interface
thorized Vertex Standard service technicians who are ex- and CT-104A, CT-106, or CT-171 PC Programming
perienced with the circuitry and fully equipped for repair Cable.
and alignment. Therefore, if a fault is suspected, contact  Vertex Standard FRB-6 Tuning Interface Box and CT-
the dealer from whom the transceiver was purchased for 160 Connection Cable.
instructions regarding repair. Authorized Vertex Standard  Vertex Standard CN-3 (P/N: A08760001) Antenna
service technicians realign all circuits and make complete Connector
performance checks to ensure compliance with factory
specifications after replacing any faulty components. Alignment Preparation & Precautions
A 50-Ohm RF Dummy Load and in-line wattmeter must
Those who do undertake any of the following alignments
be connected to the main antenna jack in all procedures
are cautioned to proceed at their own risk. Problems
that call for transmission, except where specified other-
caused by unauthorized attempts at realignment are not
wise. Correct alignment is not possible with an antenna.
covered by the warranty policy. Also, Vertex Standard
reserves the right to change circuits and alignment pro- Because of the BTL (Bridged Trans Less) Amplifier cir-
cedures in the interest of improved performance, without cuit used in the VX-261, do not connect earth side of the
notifying owners. speaker leads to chassis “ground”.
Under no circumstances should any alignment be attempt- After completing one step, read the following step to de-
ed unless the normal function and operation of the trans- termine whether the same test equipment will be required.
ceiver are clearly understood, the cause of the malfunction If not, remove the test equipment (except dummy load and
has been clearly pinpointed and any faulty components wattmeter, if connected) before proceeding.
replaced, and realignment determined to be absolutely Correct alignment requires that the ambient temperature
necessary. be the same as that of the transceiver and test equipment,
The following test equipment (and thorough familiarity and that this temperature be held constant between 68 and
with its correct use) is necessary for complete realign- 86 °F (20 ~ 30 °C). When the transceiver is brought into
ment. Correction of problems caused by misalignment the shop from hot or cold air, it should be allowed time to
resulting from use of improper test equipment is not come to room temperature before alignment.
covered under the warranty policy. While most steps do Whenever possible, alignments should be made with os-
not require all of the equipment listed, the interactions of cillator shields and circuit boards firmly affixed in place.
some adjustments may require that more complex adjust- Also, the test equipment must be thoroughly warmed up
ments be performed afterwards. Do not attempt to perform before beginning.
only a single step unless it is clearly isolated electrically
from all other steps. Have all test equipment ready before Note: Signal levels in dB referred to in the alignment pro-
beginning, and follow all of the steps in a section in the cedure are based on 0 dBµ EMF = 1 µV.
order presented.

Alignment
Test Setup Alignment Mode
Setup the test equipment as shown below for transceiver In the “Alignment Mode”, the aligned data written in the
alignment, then apply 7.5 V DC power to the transceiver. radio will be able to re-align its alignment data. The value
of each parameter can be changed to desired position by
The Alignment Tool Outline “”/“” arrow key for data up/down, “”/“” arrow key
Installation of the alignment tool for channel up/down, direct number input, and drag the
 Install the CE150 (PC Programming Software) to your mouse.
PC.
Note: when all items are aligned, it is strongly recom-
 “Alignment“ function in the “Radio“ menu tab of
mended to align according to following order. The detail
CE150.
information is written in the help document of CE150 PC
Programming Software.
1. PLL Reference Frequency (Frequency)
2. RX Sensitivity (RX Tune)
3. Squelch (SQL/RSSI)
4. TX Power <High/Low>
ê 5. Maximum Deviation <Wide/Narrow>
Please adjust the following items when needed.
¦ CTCSS Deviation <Wide/Narrow>
¦ DCS Deviation <Wide/Narrow>
¦ DTMF Alignment
¦ Sequential Tone
Unit
During alignment, you may select the value among
dBµV, µV (EMF or PD), or dBm by the “UNIT”
Action of the switches box.
When the transceiver is in the “Alignment mode,“ the ac-
tion of the SIDE-1, SIDE-2, and PTT keys are ignored.
All of the action is controlled by the PC.
Caution
Please never turn off the power supply during
alignment. If the power supply is turned off during
alignment, the alignment data will be corrupted.
When perform the RX Tune and SQL alignment,
the RF level shows this unit according to this set-
ting.
SP/LOAD Switch: LOAD

50-ohm RF Signal LOAD Switch: 16
SINAD Meter
Dummy Load Generator
CT-160
SP OUT B
Sampling
Coupler
Transceiver
MIC/SP
FRB-6 AF Signal
Inline ANT D-Sub 15-pin MIC IN Generator
Wattmeter Connector
Battery Terminal CLONE Port CT-104A, CT-106, or CT-171
Power Supply Computer

Deviation FIF-12
7.5 VDC (CE150)
Meter
Frequency Oscilloscope
Counter

Alignment
1. PLL Reference Frequency (Frequency)
This parameter align the reference frequency for PLL.
1. Press the “Frequency” button to open the “Frequency Align-
ment” window.
2. Click the “PTT” button to transmit the radio on the center fre-
quency channel.
3. Set the value to get the desired frequency according to the
following ways:
Dragging the slide bar
Clicking the arrow buttons
Pressing the left/right arrow key of the computer’s key-
board ê
Entering the value (“0” - “255”) in the “Data” box from
the computer’s keyboard
4. After getting the desired frequency, click the “PTT” button to
stop transmitting.
5. Click the “OK” button to finish the frequency alignment and
save the data.
2. RX Sensitivity (RX Tune)

This parameter align the RX BPF (Band Pass Filter) for Receive (RX) sensitivity.
The PLL Reference Frequency (Frequency) alignment must be done before this alignment is performed.
1. Press the “RX Tune” button to open the “RX Sensitivity
Alignment” window will appear.
2. Click the slide bar of the desired channel. The radio switches
to the selected channel.
3. Set the RF Signal Generator according to the indication at the
top of the screen (Setting Your SG as followings).
4. Set the value to get the best RX sensitivity (Highest RSSI
value) according to the following ways:
Clicking the arrow buttons ê
board
5. Click the “OK” button to finish the RX Sensitivity alignment
and save the data.
You may select the alignment type from the “Radio” button lo-
cated at the button of the screen (ADJ Type), as needed.
Basic: “Low Edge / Band Center/ High Edge” and select the
channel for alignment (Default).
Single: Alignment value changes only on the selected channel.
All Freq: Alignment value changes on all channels.

Alignment
3. Squelch (SQL)
This parameter align the SQL (Squelch) Sensitivity. There are several alignments as follows in the Squelch Sensitivity.
Tight SQL Level (TI NSQ W/N)
The Alignment for the Noise SQL Tight level at Wide (5k/4k) or Narrow (2.5k).
Threshold SQL Level (TH NSQ W/N)
The Alignment for the Noise SQL Threshold level at Wide (5k/4k) or Narrow (2.5k).
Tight SQL RSSI Level (TI RSSI W/N)
The Alignment for the “level 14” of the RSSI SQL level at Wide (5k/4k) or Narrow (2.5k).
TX Save RSSI Level (TX SAVE W/N)
The Alignment for the TX Save RSSI level at Wide (5k/4k) or Narrow (2.5k).
The procedure for all the alignments is as follows.
1. Click the “SQL” button to open the “SQL Alignment” menu.
2. Click the “Start” button on the desired alignment item to open
other window.
3. Set the RF Signal Generator according to the indication of the
window, then click the “OK” button.
4. The automatic alignment will start to get the optimum level.
5. The alignment result will appear in the “New” box.
On the following alignment items, click the “OK” button and
then repeat step 2-5 several times according to the indication
of the window. ê
Threshold SQL Level (Wide/Narrow)
Normal RSSI Level (Wide/Narrow)
Tight RSSI Level (Wide/Narrow)
Other alignment items has not extra step; only one step proce-
dure.
6. Click the “OK” button, then the data will be saved and the
alignment is finished.
ê

Alignment
4. TX Power
This parameter align the Transmit Output “High” or “Low” Power for the selected channel.
1. Press the “TX Power (H / L)” button to open the “TX Power
Alignment” window.
3. Click the “PTT” button on the desired channel. The radio
starts to transmit on the selected channel.
4. Set the value to get desired output power (Normally: High: 5
W, Low: 1 W) on the Power Meter according to the following
ways:
Pressing the left/right arrow key of the computer’s key- ê
board
5. After getting the desired output power, click the “PTT” but-
ton to stop transmitting.
6. Click the “OK” button to finish the TX Power alignment and
save the data.
5. Maximum Deviation <Wide> / <Narrow>

This parameter align the Maximum Deviation (Wide/Narrow).
1. Press the “Max Dev (W /N)” button to open the “Max Devia-
tion Alignment” window.
2. Set the Audio Signal Generator to 100 mV with a 1 kHz tone,
Sine Wave.
starts to transmit on the selected channel.
4. Set the value to get desired deviation (Wide: 4.2 kHz, Nar-
row: 2.1 kHz) on the deviation meter according to the follow-
ing ways:
Dragging the slide bar ê
board
5. After getting the desired deviation, click the “PTT” button to
stop transmitting.
6. Click the “OK” button to finish the Max Deviation alignment
and save the data.

Alignment
Adjust the following items if needed.
CTCSS Deviation <Wide> / <Narrow>
This parameter align the CTCSS Deviation of the selected channel.
1. Press the “CTC Dev (W/N)” button to open the “CTCSS De-
viation Alignment” window will appear.
starts to transmit with the CTCSS tone on the selected chan-
nel.
3. Set the value to get desired deviation (Nominal: Wide: 0.55
kHz, Narrow: 0.35 kHz) on the deviation meter according to
the following ways:
Clicking the arrow buttons ê
board
stop transmitting.
5. Click the “OK” button to finish the CTCSS Deviation align-
ment and save the data.
DCS Deviation <Wide> / <Narrow>

This parameter is to align the DCS Deviation of the selected channel.
1. Press the “DCS Dev (W/N)” button to open the “DCS Devia-
tion Alignment” window.
starts to transmit with the DCS code on the selected channel.
3. Set the value to get desired deviation (Nominal: Wide: 0.55
kHz, Narrow: 0.35 kHz) on the deviation meter according to
the following ways:
Pressing the left/right arrow key of the computer’s key- ê
board
4. After getting the desired deviation, click “PTT” button to stop
transmitting.
5. Click the “OK” button to finish the DCS Deviation alignment
and save the data.

Alignment
DTMF Deviation
This parameter align the DTMF Deviation.
1. Press the “DTMF” button to open the “DTMF Alignment”
window.
quency channel.
3. Set the value to get desired deviation (Nominal: 3.0 kHz) on
the deviation meter according to the following ways:
board ê
stop transmitting.
5. Click the “OK” button to finish the DTMF Deviation align-
ment and save the data.
Sequential Tone Deviation

This parameter align the Sequential Tone Deviation for the 2-Tone and 5-Tone Encoder.
1. Press the “Seq Tone” button to open the “Sequential Tone De-
viation Alignment” window will appear.
quency channel.
3. Set the value to get desired deviation (Nominal: 3.0 kHz) on
the deviation meter according to the following ways:
board ê
stop transmitting.
5. Click the “OK” button to finish the Sequential Tone Deviation
alignment and save the data.

Cloning
The VX-261 transceiver includes a convenient “Cloning” feature, which allows the programming data from one transceiver
to be transferred to another VX-261. Here is the procedure for Cloning one transceiver’s data to another.
1. Turn both transceivers “off”. 6. Press the PTT switch on the Source transceiver. The
2. Remove the plastic cap and its two mounting screws LED indicator on the top of the transceiver will glow
from the MIC/SP jack on the right side of the trans- Red, and the data will be transferred.
ceiver. Do this for both transceivers. 7. If there is a problem during the cloning process, the
3. Connect the optional CT-27 cloning cable between the LED indicator on the top of the transceiver will blink
MIC/SP jacks of the two transceivers. Red; check your cable connections and battery volt-
4. Press and hold in the PTT and SIDE-1 switches (just age, and try again.
below the PTT switch) while turning the transceiver 8. If the data transfer is successful, the LED indicator on
“on” (the order of the switch-on operation does not the top of the transceiver will turn off. Turn both trans-
matter). When Clone mode is successfully activated in ceivers “off” and disconnect the CT-27 cable. You can
this step. then turn the transceivers back on, and begin normal
5. On the Destination transceiver, press the SIDE-1 operation.
switch. The LED indicator on the top of the transceiv- 9. Replace the plastic cap and its two mounting screws.
er will glow Green.
PTT Switch  PTT Switch 
SIDE-1 Switch  SIDE-1 Switch 
CT-27 Optional Cloning Cable

Main Unit: Type “G7”
Circuit Diagram (FR027720D)

Main-2 Unit: Type “G6”
Circuit Diagram (FR027830A)

No portion of this manual may be reproduced without the per-
mission of Vertex Standard LMR, Inc.
Vertex Standard is a trademark of Vertex Standard LMR, Inc.
All other trademarks are the property of their respective owners.
©2015 Vertex Standard LMR, Inc.
All rights reserved.

VX-261 Uhf SM Ec128u90c

Uploaded by

Copyright:

Available Formats

VX-261 Uhf SM Ec128u90c

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

VX-261 Uhf SM Ec128u90c

Uploaded by

Copyright:

Available Formats

Vertex Standard LMR, Inc.

VX-261 UHF FM Transceiver Service Manual 1

Receiver (Measured by TIA/EIA-603)

Transmitter (Measured by TIA/EIA-603)

Specifications subject to change without notice or obligation.

VX-261 UHF FM Transceiver Service Manual 2

Receiver (Measured by ETC 300 086)

Transmitter (Measured by ETC 300 086)

Specifications subject to change without notice or obligation.

VX-261 UHF FM Transceiver Service Manual 3

CB6642000 CB6987000 (TYPE “G7”)

FRONT CASE ASSY (Component) RA1612600

MAIN UNIT (Component)

REF. VXSTD P/N DESCRIPTION QTY.

Non-designated parts are available only as part of a designated assembly.

VX-261 UHF FM Transceiver Service Manual 4

MAIN UNIT ASSY CB6988000: TYPE “G7”

MAIN-2 UNIT ASSY CB6989000: TYPE “G6”

When replace a chip fuse,

VX-261 UHF FM Transceiver Service Manual 5

VX-261 UHF FM Transceiver Service Manual 6

1-2. First Mixer 1-5. Squelch Circuit

VX-261 UHF FM Transceiver Service Manual 7

VX-261 UHF FM Transceiver Service Manual 8

VX-261 UHF FM Transceiver Service Manual 9

SP/LOAD Switch: LOAD

Power Supply Computer

VX-261 UHF FM Transceiver Service Manual 10

2. RX Sensitivity (RX Tune)

VX-261 UHF FM Transceiver Service Manual 11

VX-261 UHF FM Transceiver Service Manual 12

5. Maximum Deviation <Wide> / <Narrow>

VX-261 UHF FM Transceiver Service Manual 13

DCS Deviation <Wide> / <Narrow>

VX-261 UHF FM Transceiver Service Manual 14

Sequential Tone Deviation

VX-261 UHF FM Transceiver Service Manual 15

PTT Switch  PTT Switch 

SIDE-1 Switch  SIDE-1 Switch 

CT-27 Optional Cloning Cable

VX-261 UHF FM Transceiver Service Manual 16

VX-261 UHF FM Transceiver Service Manual 17

VX-261 UHF FM Transceiver Service Manual 18

VX-261 UHF FM Transceiver Service Manual 17

You might also like