DT820

TUNNELING DRILL
TECHNICAL SPECIFICATION

The Sandvik DT820 is a two boom electro hydraulic KEY FEATURES

jumbo for fast and accurate drilling in tunneling and Coverage area 110 m² (14 210 x 8 420 mm)
cavern excavation of 12 - 110 m² cross sections. Hydraulic rock drill 2 x RDX5 (20 kW)
Drill feed 2 x TF500-16’
The hydraulic controlled drilling system with Boom 2 x SB90
added automatic functions and different optional Control system THC560, hydraulic
instrumentation levels enable productive and high Hole length Up to 6 180 mm
quality excavation. Turning width (T-section) 4 840 mm (with TF500-16’)
Transport / drilling width 2 500 mm / 3 000 mm
The RDX5 rock drills deliver superior performance with Transport / drilling height 2 750 mm / 3 600 mm
high consumable life, lowering operating costs and Transport length 14 930 mm (with TF500-16’)
giving long service interval. 26 500 kg (without utility boom)
Total weight
depending on options
The SB90 universal booms have a large optimum shaped 28 900 kg (with utility boom)
Total weight
coverage and full automatic parallelism. The booms can depending on options
also be used for cross-cutting and bolt hole drilling.

An optional utility boom for bolting and utility works is

available. The powerful 4-wheel-drive center articulated
carrier ensures rapid and safe tramming with good
balance.

1. SANDVIK DT820 - TUNNELING DRILL

HYDRAULIC ROCK DRILL DRILLING CONTROL SYSTEM
Type of rock drill RDX5 (TS2-433) Type of control system THC560 (TS2-361)
Percussion power 20 kW Operating principle Hydraulic control
Percussion pressure Max. 220 bar Direct control
Percussion rate 67 Hz Manual boom control Fully proportional
Rotation speed Max. 250 rpm (with OMS125) Hydraulic parallelism

Rotation torque 625 Nm (with OMS125)

Manual collaring
Hole size (drifting) 43 - 64 mm Feed / percussion control
Drilling control
Hole size (cut hole) 76 - 127 mm Anti-jamming system
Flushing control
T38 - Hex 35 - R32
Recommended rod T38 - Hex 35 - Alpha 330 Automatic cycle Stop and return automatics
T38 - Hex 35 -R35

Shank adapter (male) T38 ELECTRIC SYSTEM

Weight 210 kg Standard voltage 380 - 690 V (± 10%)
Length 955 mm Total input power 135 kW
Profile height 87 mm Main switch MSE20
IP classification Specification TS2-132
FEED Starting method Star-delta starter 380 - 690 V
Type of TF500-12’ TF500-14’ TF500-16’ TF500-18’ TF500-20’ Automatic cable reel TCR4E
feed Optional Optional Standard Optional Optional Cable reel control (in / out) Operator station
Feed Front lights
25 kN 25 kN 25 kN 25 kN 25 kN 8 x 35 W HID (24V)
force (Max.) (combined working and driving)

Total length 5 270 5 880 6 490 7 100 7 710 Rear lights

4 x 35 W HID (24 V)
Hole length 3 440 4 050 4 660 5 270 5 880 (combined working and driving)

Rod length 3 700 4 305 4 915 5 525 6 135 Rear parking / brake lights 1 x Red LED (24V)
Net Stair case service lights LED (24V)
500 530 560 590 620
weight (kg)
AIR AND WATER SYSTEM
BOOM Flushing of holes By water
Type of boom SB90 (TS2-265) Water booster pump type WBP2 (11 kW)
Parallel coverage 90 m² Water pump capacity 100 l/min at 15 bar (5 bar inlet)
Parallelism Hydraulic Water pump inlet pressure 2 - 7 bar
Boom extension 1 800 mm Flushing water pressure 10 - 15 bar
Feed extension 1 650 mm Shank lubrication device SLU-2 (air / oil mist)
Boom weight, net 2 650 kg Air compressor CTN10 (1.0 m³/min at 7 bar)
Roll-over angle 358° Oil consumption 180 - 250 g/h
Air consumption 250 - 350 l/min
UTILITY BOOM (OPTIONAL)
Type of utility boom SUB3A (TS2-307) OPERATOR’S SAFETY CANOPY
Boom extension 2 x 2 000 mm Canopy certification FOPS (ISO 3449)
Boom weight,net 2 350 kg Unit height in tramming 3 600 mm
Max allowed load 510 kg Sound pressure level Cabin < 103 dB(A)
Max allowed load with safety according to EN 16228 Emitted 126 dB(A)
400 kg
canopy Operation Standing drilling, seated tramming

HYDRAULIC SYSTEM
Powerpack HPP555 (2 x 55 kW)
Percussion pump 110 cc (variable)
Rotation pump 60 cc (variable)
Filtration size (pressure / return) 20 µ / 10 µ
Oil tank volume 290 liters
Filling pump for hydraulic oil Electric
Cooler for hydraulic oil OW30 oil-to-water (2 x 30 kW)

2. SANDVIK DT820 - TUNNELING DRILL

CARRIER OPTIONAL ITEMS
Type of carrier TC8 (frame-steered) Electric system
Carrier articulation ± 37° *Voltage option 1 000 V (50 Hz), DOL starting
system
Rear axle oscillation ± 8° Electric cables Specification TS2-121
Ground clearance 400 mm Spooling device for cable reel For voltages 690 - 1 000 V
Diesel engine MB OM904LA, 110 kW, Tier 3, Stage IIIA Ground fault and overcurrent unit VYK
Electricity outlet on front carrier 1 x 400 V or 2 x 230 V 16A
Transmission Hydrodynamic, Spicer T20 000 Remote control for reel(s) At rear machine
Axles Dana Spicer 113 (front and rear) Amber flashing light LED (24 V)
Tires 14.00-24 PR28
Air and water system
Service brakes Hydraulically applied wet disc brakes
Flushing flow supervision 2 booms
Parking / emergency brakes SAHR type, fail safe wet disc brakes *Air compressor CTN16 (1.6 m³/min at 7 bar)
Fuel tank 150 liters Air mist flushing External air / water supply (incl. IP5
air cleaner)
Horizontal (0%): 16 km/h End of hole flushing 2 x 80 liters receiver (incl. IP5 air
Tramming speed
14% = 1:7 = 8º: 5.4 km/h cleaner).
Gradeability / sideways tilt Max. 15° / 5° External air connection IP5 air cleaner
Water hose reel THR2.5E with 38 mm (1 ½”), 65 m
Carrier stabilization TJ60 (front), TJ75 (rear)
Water hose 38 mm (1 ½”), 65 m
Hand throttle Standard
Hand held fire extinguisher 7.7 kg (type ABC) Operator’s safety canopy
Carrier centralized greasing Specification TS2-463 Reduced tramming speed 3rd gear lockout
Tramming alarm Standard
Fire suppression system
Knowledge Box™ Connectivity solution (TS2-535) Additional fire extinguisher 7.7 kg (type ABC)
Colour scheme Sandvik standard Manual system Ansul, 6 nozzles (TS2-460)
Automatic system Ansul, 6 nozzles (TS2-460)
1 x Operator’s manual
1 x Maintenance manual Carrier
Documentation 1 x Technical manual (in English only) *High speed carrier TC8, incl. MB OM906LA, 170 kW,
1 x Parts manual (in English only) Tier 3, Stage IIIA, with Spicer
2 x Toolman USB key T32 000 transmission
Exhaust catalyzer For Tier 3 engines
OPTIONAL ITEMS Fast filling system For fuel or complete
Rod rack on carrier side 12 to 20 ft rods
Feed Tramming camera Rear
*Feed length 12’, 14’, 18’, 20’ Wheel chocks and holders 2 pieces
*Telescopic feed TFX6/12, TFX8/14, TFX10/16
Rod retainer TRR1 with TF or TFX feed (incl. Extra items
safety wire) Spare rock drill RDX5
Spare wheel assembly Standard
Utility boom
Special tools for rock drill Field tool set (TS2-434)
Safety canopy FOPS approved
Complete tool set (TS2-435)
Sliding FOPS safety canopy
Tunnel laser set
Spot lights 2 x 17 W LED
Documentation Extra manuals
Rod racks For 4 pcs of 10 or 12 ft rods
RX expansion bolt installation kit D30 mm or D41 mm *) Replaces standard feature

Hydraulic system
Utility boom pump 60cc (gear)
*Filling pump for hydraulic oil Manual
*Biodegradable oils Shell Naturelle HFE46/68

Control system
Constant speed drilling Replaces feed / percussion control
Drilling instrument TMS+

Cleaning system
Low pressure system with reel Up to 15 bar (TS2-343)
High pressure system with reel Up to 180 bar (TS2-343)

Greasing systems
Automatic system Lincoln (for carrier, boom,rod han-
dler and utility boom)
Manual system Specification TS2-463

3. SANDVIK DT820 - TUNNELING DRILL

 TS2-389:03/ENG/METRIC ©Sandvik Mining and Rock Solutions 2022 SANDVIK is a registered trademark owned by Sandvik Intellectual Property AB in Sweden and other countries.
TF500-12’ TF500-14’ TF500-16’ TF500-18’ TF500-20’
Feed length 5 330 mm 5 940 mm 6 550 mm 7 160 mm 7 770 mm
Overall length 14 680 mm 14 900 mm 14 900 mm 15 350 mm 16 400 mm
Overall length with TRR1 14 710 mm 14 930 mm 14 930 mm 15 380 mm 16 430 mm

850

SANDVIK
DT820

2 750
2 370
1 410
400 22°
15° 2 300
3 200 4 120
Overall length

C
R Angle (A) Radius (R) T-cross (C)
DT820 (TF500-12’) mm 37° 7 940 4 730
4 655 DT820 (TF500-14’) mm 37° 7 940 4 730
750
DT820 (TF500-16’) mm 37° 8 050 4 840
750 DT820 (TF500-18’) mm 37° 8 190 4 980
A
DT820 (TF500-20’) mm 37° 8 300 5 090

All dimensions in mm

Sandvik Mining and Rock Solutions reserves the right to make changes to the information on this data sheet without prior notification to users.
Please contact a Sandvik representative for clarification on specifications and options.

ROCKTECHNOLOGY.SANDVIK

4. SANDVIK DT820 - TUNNELING DRILL