Precision, Very Low Noise,

Low Input Bias Current Op Amp

Enhanced Product AD8672-EP
FEATURES PIN CONFIGURATION
Voltage noise density: 2.8 nV/√Hz typical OUT A 1 8 V+
Peak-to-peak noise: 77 nV p-p typical –IN A 2 AD8672-EP 7 OUT B
+IN A 3 TOP VIEW 6 –IN B
Gain bandwidth product: 10 MHz (Not to Scale)

13063-001
V– 4 5 +IN B
Low input bias current: 14 nA maximum
Low offset voltage: 75 μV maximum Figure 1.
High open-loop gain: 1000 V/mV (120 dB)
Low supply current per amplifier: 3 mA typical
Dual-supply operation: ±5 V to ±15 V GENERAL DESCRIPTION
Unity-gain stable The AD8672-EP is a very high precision amplifier featuring very
No phase reversal low noise, very low offset voltage and drift, low input bias current,
ENHANCED PRODUCT FEATURES 10 MHz bandwidth, and low power consumption. Outputs are
stable with capacitive loads of over 1000 pF. Supply current is less
Supports defense and aerospace applications (AQEC standard)
than 3 mA per amplifier at 30 V.
Extended temperature range: −55°C to +125°C
Controlled manufacturing baseline The combination of ultralow noise, high precision, speed, and
One assembly/test site stability within the AD8672-EP is unmatched. Applications for
One fabrication site this amplifier include high quality PLL filters, precision filters,
Enhanced product change notification medical and analytical instrumentation, precision power supply
Qualification data available on request controls, ATE, data acquisition, and precision controls, as well
as professional quality audio.
APPLICATIONS
The AD8672-EP is available in an 8-lead SOIC narrow package.
Phase-locked loop (PLL) filters
It is specified over a −55°C to +125°C temperature range.
Filters for GPS
Instrumentation Additional application and technical information can be found
Sensors and controls in the AD8672 data sheet.
Professional quality audio

Rev. 0 Document Feedback

Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Tel: 781.329.4700 ©2015 Analog Devices, Inc. All rights reserved.
Trademarks and registered trademarks are the property of their respective owners. Technical Support www.analog.com
AD8672-EP Enhanced Product

TABLE OF CONTENTS
Features .............................................................................................. 1  Electrical Characteristics, ±15 V .................................................4 
Enhanced Product Features ............................................................ 1  Absolute Maximum Ratings ............................................................5 
Applications ....................................................................................... 1  Thermal Resistance .......................................................................5 
Pin Configuration ............................................................................. 1  ESD Caution...................................................................................5 
General Description ......................................................................... 1  Typical Performance Charateristics ................................................6 
Revision History ............................................................................... 2  Outline Dimensions ..........................................................................8 
Specifications..................................................................................... 3  Ordering Guide .............................................................................8 
Electrical Characteristics, ±5 V .................................................. 3 

REVISION HISTORY
9/15—Revision 0: Initial Version

Rev. 0 | Page 2 of 8
Enhanced Product AD8672-EP

SPECIFICATIONS
ELECTRICAL CHARACTERISTICS, ±5 V
VSY = ±5.0 V, VCM = 0 V, TA = 25°C, unless otherwise specified.
Table 1.
Parameter Symbol Test Conditions/Comments Min Typ Max Unit
INPUT CHARACTERISTICS
Offset Voltage VOS 20 75 μV
−55°C < TA < +125°C 30 125 μV
Offset Voltage Drift ∆VOS/∆T −55°C < TA < +125°C 0.3 0.8 μV/°C
Input Bias Current IB −14 +3 +14 nA
25°C < TA < 125°C −20 +5 +20 nA
−55°C < TA < +125°C −60 +8 +60 nA
Input Offset Current IOS −14 +6 +14 nA
25°C < TA < 125°C −20 +6 +20 nA
−55°C < TA < +125°C −60 +8 +60 nA
Input Voltage Range −2.5 +2.5 V
Common-Mode Rejection Ratio CMRR VCM = −2.5 V to +2.5 V 100 120 dB
Large Signal Voltage Gain AVO RL = 2 kΩ, VO = −3 V to +3 V 1000 6000 V/mV
Input Capacitance
Common Mode CINCM 6.25 pF
Differential Mode CINDM 7.5 pF
Input Resistance
Common Mode RIN 3.5 GΩ
Differential Mode RINDM 15 MΩ
OUTPUT CHARACTERISTICS
Output Voltage
High VOH RL = 2 kΩ, −55°C to +125°C +3.8 +4.0 V
RL = 600 Ω +3.7 +3.9 V
Low VOL RL = 2 kΩ, −55°C to +125°C −3.9 −3.8 V
RL = 600 Ω −3.8 −3.7 V
Output Current IOUT ±10 mA
POWER SUPPLY
Power Supply Rejection Ratio PSRR VS = ±4 V to ±18 V 110 130 dB
Supply Current per Amplifier ISY VO = 0 V 3 3.5 mA
−55°C < TA < +125°C 4.2 mA
DYNAMIC PERFORMANCE
Slew Rate SR RL = 2 kΩ 4 V/μs
Settling Time tS To 0.1% (4 V step, G = 1) 1.4 μs
To 0.01% (4 V step, G = 1) 5.1 μs
Gain Bandwidth Product GBP 10 MHz
NOISE PERFORMANCE
Peak-to-Peak Noise en p-p 0.1 Hz to 10 Hz 77 100 nV p-p
Voltage Noise Density en f = 1 kHz 2.8 3.8 nV/√Hz
Current Noise Density in f = 1 kHz 0.3 pA/√Hz
Channel Separation CS f = 1 kHz −130 dB
f = 10 kHz −105 dB

Rev. 0 | Page 3 of 8
AD8672-EP Enhanced Product
ELECTRICAL CHARACTERISTICS, ±15 V
VS = ±15.0 V, VCM = 0 V, TA = 25°C, unless otherwise specified.

Table 2.
Parameter Symbol Test Conditions/Comments Min Typ Max Unit
INPUT CHARACTERISTICS
Offset Voltage VOS 20 75 μV
−55°C < TA < +125°C 30 125 μV
Offset Voltage Drift ∆VOS/∆T −55°C < TA < +125°C 0.3 0.8 μV/°C
Input Bias Current IB −14 +3 +14 nA
25°C < TA < 125°C −20 +5 +20 nA
−55°C < TA < +125°C −60 +8 +60 nA
Input Offset Current IOS −14 +6 +14 nA
25°C < TA < 125°C −20 +6 +20 nA
−55°C < TA < +125°C −60 +8 +60 nA
Input Voltage Range −12 +12 V
Common-Mode Rejection Ratio CMRR VCM = −12 V to +12 V 100 120 dB
Large Signal Voltage Gain AVO RL = 2 kΩ, VO = −10 V to +10 V 1000 6000 V/mV
Input Capacitance
Common Mode CINCM 6.25 pF
Differential Mode CINDM 7.5 pF
Input Resistance
Common Mode RIN 3.5 GΩ
Differential Mode RINDM 15 MΩ
OUTPUT CHARACTERISTICS
Output Voltage
High VOH RL = 2 kΩ, −55°C to +125°C 13.2 13.8 V
RL = 600 Ω 11 12.3 V
Low VOL RL = 2 kΩ, −55°C to +125°C −13.8 −13.2 V
RL = 600 Ω −12.4 −11 V
Output Current IOUT ±20 mA
Short Circuit Current ISC ±30 mA
POWER SUPPLY
Power Supply Rejection Ratio PSRR VS = ±4 V to ±18 V 110 130 dB
Supply Current per Amplifier ISY VO = 0 V 3 3.5 mA
−55°C < TA < +125°C 4.2 mA
DYNAMIC PERFORMANCE
Slew Rate SR RL = 2 kΩ 4 V/μs
Settling Time tS To 0.1% (10 V step, G = 1) 2.2 μs
To 0.01% (10 V step, G = 1) 6.3 μs
Gain Bandwidth Product GBP 10 MHz
NOISE PERFORMANCE
Peak-to-Peak Noise en p-p 0.1 Hz to 10 Hz 77 100 nV p-p
Voltage Noise Density en f = 1 kHz 2.8 3.8 nV/√Hz
Current Noise Density in f = 1 kHz 0.3 pA/√Hz
Channel Separation CS f = 1 kHz −130 dB
f = 10 kHz −105 dB

Rev. 0 | Page 4 of 8
Enhanced Product AD8672-EP

ABSOLUTE MAXIMUM RATINGS

Table 3. THERMAL RESISTANCE
Parameter Rating θJA is specified for the worst-case conditions, that is, θJA is
Supply Voltage 36 V specified for the device soldered on a 4-layer circuit board for
Input Voltage VS− to VS+ surface-mount packages.
Differential Input Voltage ±0.7 V
Table 4.
Output Short-Circuit Duration Indefinite
Storage Temperature Range −65°C to +150°C Package Type θJA θJC Unit
Operating Temperature Range −55°C to +125°C 8-Lead SOIC_N (R-8) 120 43 °C/W
Junction Temperature Range −65°C to +150°C
Lead Temperature Range (Soldering, 60 sec) 300°C
ESD CAUTION
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.

Rev. 0 | Page 5 of 8
AD8672-EP Enhanced Product

TYPICAL PERFORMANCE CHARATERISTICS

4.0 135
VS = ±2.5V TO ±18V

3.5 134
VS = ±15V

3.0 133
SUPPLY CURRENT (mA)

VS = ±5V
2.5 132

PSRR (dB)
2.0 131

1.5 130

1.0 129

0.5 128

0 127

13063-104
13063-101
–75 –50 –25 0 25 50 75 100 125 –75 –50 –25 0 25 50 75 100 125
TEMPERATURE (°C) TEMPERATURE (°C)

Figure 2. Supply Current vs. Temperature Figure 5. PSRR vs. Temperature

100 100
VS = ±5V VS = ±15V
80 TA = –55°C TO +125°C 80 TA = –55°C TO +125°C

60 60 MEAN + 3σ

40 40
MEAN + 3σ
20 20
VOS (µV)
VOS (µV)

0 0 MEAN
MEAN

–20 –20

–40 MEAN – 3σ –40

MEAN – 3σ
–60 –60

–80 –80

–100 –100

13063-105
13063-102

–75 –50 –25 0 25 50 75 100 125 –75 –50 –25 0 25 50 75 100 125
TEMPERATURE (°C) TEMPERATURE (°C)

Figure 3. Input Offset Voltage (VOS) vs. Temperature, VS = ±5 V Figure 6. Input Offset Voltage (VOS) vs. Temperature, VS = ±15 V

25 16
VS = ±5V VS = ±15V
TA = –55°C TO +125°C TA = –55°C TO +125°C
14
20
12
NUMBER OF AMPLIFIERS
NUMBER OF AMPLIFIERS

10
15

10 6

4
5
2

0 0
0
0.05
0.10
0.15
0.20
0.25
0.30
0.35
0.40
0.45
0.50
–0.50
–0.45
–0.40
–0.35
–0.30
–0.25
–0.20
–0.15
–0.10
–0.05
0
0.05
0.10
0.15
0.20
0.25
0.30
0.35
0.40
0.45
0.50
–0.50
–0.45
–0.40
–0.35
–0.30
–0.25
–0.20
–0.15
–0.10
–0.05

13063-106
13063-103

TCVOS (µV/°C) TCVOS (µV/°C)

Figure 4. Input Offset Voltage Drift (TCVOS) Distribution, VS = ±5 V Figure 7. Input Offset Voltage Drift (TCVOS) Distribution, VS = ±15 V

Rev. 0 | Page 6 of 8
Enhanced Product AD8672-EP
3.5 4.0
VS = ±5V VS = ±15V

3.0 3.5

–IB
3.0
2.5

2.5
2.0 –IB
IB (nA)

IB (nA)
+IB 2.0
1.5
1.5
+IB
1.0
1.0

0.5 0.5

0 0

13063-107

13063-110
–75 –50 –25 0 25 50 75 100 125 –75 –50 –25 0 25 50 75 100 125
TEMPERATURE (°C) TEMPERATURE (°C)

Figure 8. Input Bias Current (IB) vs. Temperature, VS = ±5 V Figure 11. Input Bias Current (IB) vs. Temperature, VS = ±15 V

14.5 –11.0
RL = 2kΩ VS = ±15V
14.0
–11.5
13.5
OUTPUT VOLTAGE (V)

OUTPUT VOLTAGE (V)

–12.0
13.0

12.5 –12.5
RL = 600Ω RL = 600Ω
12.0 –13.0

11.5
–13.5
11.0 RL = 2kΩ

–14.0
10.5
VS = ±15V
10.0 –14.5
13063-108

13063-111
–75 –50 –25 0 25 50 75 100 125 –75 –50 –25 0 25 50 75 100 125
TEMPERATURE (°C) TEMPERATURE (°C)

Figure 9. Output Voltage High vs. Temperature Figure 12. Output Voltage Low vs. Temperature

30000

25000

20000
AVO (V/mV)

VS = ±5V
15000

10000

VS = ±15V
5000

0
13063-109

–75 –50 –25 0 25 50 75 100 125

TEMPERATURE (°C)

Figure 10. Open-Loop Gain (AVO) vs. Temperature

Rev. 0 | Page 7 of 8
AD8672-EP Enhanced Product

OUTLINE DIMENSIONS
5.00 (0.1968)
4.80 (0.1890)

8 5
4.00 (0.1574) 6.20 (0.2441)
3.80 (0.1497) 1 5.80 (0.2284)
4

1.27 (0.0500) 0.50 (0.0196)

BSC 45°
1.75 (0.0688) 0.25 (0.0099)
0.25 (0.0098) 1.35 (0.0532)
8°
0.10 (0.0040) 0°
COPLANARITY 0.51 (0.0201)
0.10 1.27 (0.0500)
0.31 (0.0122) 0.25 (0.0098)
SEATING 0.40 (0.0157)
PLANE 0.17 (0.0067)

COMPLIANT TO JEDEC STANDARDS MS-012-AA

CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS

012407-A
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.

Figure 13. 8-Lead Standard Small Outline Package [SOIC_N]

Narrow Body (R-8)
Dimensions shown in millimeters and (inches)

ORDERING GUIDE
Model1 Temperature Range Package Description Package Option
AD8672TRZ-EP −55°C to +125°C 8-Lead Standard Small Outline Package [SOIC_N] R-8
AD8672TRZ-EP-R7 −55°C to +125°C 8-Lead Standard Small Outline Package [SOIC_N] R-8
1
Z = RoHS Compliant Part.

©2015 Analog Devices, Inc. All rights reserved. Trademarks and

registered trademarks are the property of their respective owners.
D13063-0-9/15(0)

Rev. 0 | Page 8 of 8