1156119B LCF55

Owner’s Manual, Operating
Instructions Manual, and

Replacement Parts Manual
Lift-Rite Titan Series Hand Pallet Trucks
Model LCF55 - Freezer Special
Lift-Rite, 5975 Falbourne Street, Mississauga, Ontario L5R3L8 Tel: Toll Free from USA: 1-800-558-6012; Tel: 1-905-456-2603 (Canada and International)
Fax: 1-905-456-1383 Owner’s Manual, Operating Instructions, and Replacement Parts Manual, Publication Number 1156119B ©2013 Dated 08 Oct 2013
This publication, 1156119B, applies to the Lift-Rite Titan Series Hand Pallet Trucks, Model LCF55 version,
and to all subsequent releases of this product until otherwise indicated in new editions. Changes occur
periodically to the information in this publication.
To order additional copies of this manual, part number 1156119B, contact your local authorized Lift-Rite
Sales and Service Center.
If you need assistance with your lift truck, contact your local authorized Lift-Rite Sales and Service Center.
To locate your Sales and Service Center, go to www.liftrite.com
©2013
TABLE OF CONTENTS
DELIVERY INSPECTION 2
OPERATING INSTRUCTIONS 2
SAFETY PROCEDURES 3
DAILY INSPECTION 3
MAINTENANCE 4-5
TROUBLESHOOTING 6
PARTS 7-9
Hydraulic Assembly 7
LCF55 Chassis 8
Recycling Old Parts 9
WARRANTY 10
1
SAFETY SHOES
Always wear safety shoes when working with hand pallet trucks.
PROTECTIVE GLASSES
When assembling or dismantling a hand pallet truck, protective
glasses must be worn to avoid personal injury.
OPERATOR’S RESPONSIBILITY
While operating a hand pallet truck, always wear safety equipment
and operate in a responsible manner to ensure a safe work area.
DELIVERY INSPECTION
Visually inspect hand pallet truck frame components and hydraulic unit for damage during
shipment by carrier. If damage is evident, notify delivering carrier immediately and file necessary
claims. Test the hand pallet truck pump for proper operation. If the hydraulic pump does not
respond to movement of the handle, an air lock may have developed during shipping. To
remedy this, go to the user friendly TROUBLESHOOTING guide in this manual.
OPERATING INSTRUCTIONS
(Read and understand prior to using this product)
To raise the load, push down on NOTE:

the fingertip control. Pump the The neutral position disengages
handle to raise the load from the the pump from the lifting
floor. mechanism. This frees the handle,
which makes pulling loads easier.
To lower the load, pull up on the In addition, the pump is not
fingertip control. subject to shock pressures while
the truck is in motion.
For free handle movement, place
the fingertip control in the neutral
position.
2
SAFETY PROCEDURES
(Read and understand prior to using this product)
• Read and obey all labels on this product. If you have any questions about these, ask your
supervisor.
• Do not operate this hand pallet truck unless you are authorized and trained to do so.
• Never overload your hand pallet truck. Stay within its rated capacity.
• Do not operate this truck if damaged or not in proper working order.
• Distribute the load evenly on the forks. Do not concentrate loads at one point or load one fork
more than the other.
• When the load impairs visibility, the hand pallet lift truck should be pulled and not pushed.
• Always look where you are operating. Keep a clear view.
• Only handle loads on flat level surfaces. Do not use a loaded truck on inclines or declines.
• Never carry passengers.
• Never put your feet, hands, or any other body part under the frame assembly.
• Always yield right of way to pedestrians.
• Do not allow your hand pallet truck to drop from one level to another. Even a drop of 1 in.
(25 mm) more than doubles the effective load momentarily and results in a loading that can bend
or break components.
• Move loads only with the hand pallet truck in its lowest position.
• Always make sure that the load is stable before moving to eliminate the opportunity for load
shift.
• Use extreme care when rounding corners. Too fast a speed could cause a hand pallet lift truck to
tip. If loaded, the load could shift and fall.
• When not in use, fully lower the forks.
DAILY INSPECTION
At the start of your shift, check the items listed below. Report any malfunction or unsafe conditions
to your supervisor. Do not use this product until it is repaired.
CHECK Hydraulic Chassis/ Lifting/

POINTS Steering System Wheels Handle Lowering Labels
ACTION Check full Check for Check for wear, Check for Check for Check for
rotation excessive oil damage, and damage and function readability
on exterior remove debris remove debris
and check for
function
3
MAINTENANCE
LUBRICATION
All pivot points are equipped with permanently lubricated bushings and bearings. To increase
bearing life, it is recommended that a few drops of light machine oil be applied at each pivot point
every 3 months. The thrust plate is equipped with three grease fittings. Apply grease under normal
conditions every 3 months.
PUSH BAR LINKAGE ADJUSTMENT

If the forks do not rise evenly at the tips, or the roller levers begin to drag on the floor, the following
adjustment is necessary:
LCF55 MODEL
• Turn the hand pallet truck over so that the underside of the forks are accessible.
• Remove one split pin (PN-20269B) with 3/16 in. punch.
• Remove pin (PN-20227) from bracket.
• Adjust eyebolts (PN-20226). Turn counterclockwise to raise fork tips and clockwise to lower
fork tips.
• Replace pin (PN-20227) through eyebolt and replace split pin (PN-20269B).
• When adjusted properly, the forks should be 3 in. low height from ground level in the
lowered position.
4
MAINTENANCE (CONT.)
HYDRAULIC SYSTEM
Your hydraulic system is maintenance free. Do not add hydraulic oil unless there is, or has been, a
leak. Use ISO VG 15 grade hydraulic oil or equal for LCF55 model trucks. Other oils, fluids, or
solvents may damage your hydraulic system. If you suspect additional oil is required, follow these
steps:
1. Check for and fix any possible oil leaks.
2. Lower the truck and load with 600 lbs. (approximate).
3. Pump the truck to its maximum lift height.
4. Measure the vertical height of the exposed piston (215030) and refer to the chart below.
Distance (inches) 5-1/8 in. 4-3/4 in. 4-3/8 in. 4 in. 3-1/2 in. 3-1/8 in. 2-3/4 in. 2-3/8 in.
Oil to add (Fl. Oz.) 0 2.7 3.0 3.4 3.7 4.0 4.4 4.7
ADDING OIL (IF REQUIRED)

1. Place and secure the truck on its right side (release valve facing the floor).
2. Pull up on the release lever (173765) and extend the lift piston fully.
3. Remove screw (221586) and add the amount of oil determined by the chart in step 4.
4. Reinstall screw (221586) but do not tighten. Leave a 1/32 in. gap.
5. Pull up on the release lever (173765) and collapse the lift piston until oil starts to
ooze from the screw.
CAUTION! - It is extremely important that step 5 is performed. Otherwise, air in
the pump can force out the wiper seal (20066). Take care when adding oil not to
introduce impurities into the hydraulic system.
6. Tighten the screw (221586) fully and return the truck upright.
5
TROUBLESHOOTING
CONDITION POSSIBLE CAUSE ACTION

Pump does not lift load. An air lock in the hydraulic Pull up on fingertip control and hold
system. while pumping the handle 8 to 10 times
to bleed air from the system.
Lifting, neutral, and lowering Chain anchor out of adjustment. Turn nut (158452) on chain anchor
do not function properly. clockwise until pumping action, while in
neutral, does not raise forks.
Forks raise and sink with Dirt or foreign particle caught in Pull up on fingertip control and hold
pump action. cone valve seat. while pumping the handle 8 to 10 times
to purge the valve system.
Pump does not lift load to Pump is low on oil. Check for and fix any leaks. Then add oil
complete raised height. as instructed in the MAINTENANCE
section.
Forks are not lowering Push jam nut is loose. Push bars Refer to Push Bar Linkage Adjustment
completely. require adjustment. in the MAINTENANCE section.
6
COMPLETE HYDRAULIC ASSEMBLY (1151454/001)
ITEM DESCRIPTION QTY PART NO.

1 COMPLETE HANDLE (ITEMS 2-10) 1 1154730/001
2 SPLIT PIN 1 20105
3 CONTROL LEVER 1 173765
4 CONTROL LEVER SLEEVE 1 54140
5 CONTROL LEVER SPRING 1 218182
6 CHROME BALL 2 20065
7 CONTROL ROD ASSEMBLY 1 253089
8 SPLIT PIN 1 20461
9 AXLE 1 47930
10 ROLLER WITH BUSHING 1 165196
11 AXLE 1 7500087
12 ADJUSTING NUT 1 158452
13 LOCKING PIN 1 220312
14 LOWERING ARM 1 215128
15 COVER 2 156623BT
16 LOCKING RING 1 7500035
17 SLEEVE 1 215803
18 WASHER 1 215282
19 SPRING 1 7500037
20 PISTON 1 215030
21 PISTON 1 215286
22 SEALING RING 1 7500105CE
24 SEALING 1 20066
25 SEALING 1 215866
26 SEALING 1 215867
28 BUSHING 2 215913
29 SCREW 1 221586
30 O-RING 1 24213
31 WASHER 1 235545
32 SPRING 1 39106
33 VALVE CONE 1 223935
34 SCREW (OVERLOAD) 1 221232
35 O-RING (OVERLOAD) 1 22032
36 SPRING (OVERLOAD) 1 221227
37 GUIDE PIN (OVERLOAD) 1 221231
38 BALL (OVERLOAD) 1 22055
39 BALL 1 20065
40 WASHER 1 215288
41 O-RING 1 22032
42 VALVE BODY 1 7500112
43 SPRING 1 47071
45 U-RING 1 7500100
46 PISTON 1 7500116
47 LOWERING VALVE COMPLETE 1 7518604CE
48 BALL BEARING 1 228275
51 THRUST PLATE 1 7500028
53 GREASE NIPPLE 1 27662
56 AXLE 1 227907
57 BEARING 4 210062
58 WHEEL COMPLETE - NYLON 2 160421BT
60 HYDRAULIC UNIT 1 7500028
REBUILD KIT 1 7514681
7
MODEL LCF55 CHASSIS DIAGRAM
ITEM DESCRIPTION QTY PART NO.

1 CHASSIS COMPLETE - 27X48 IN. 1 1154178/001
2 TORSION BAR - 27 IN. WIDE TRUCK 1 1156049
3 BUSHING 6 PN-20203A
4 BULKHEAD PIN 2 PN-20204
5 SPRING PIN 2 20174
6 EYE BOLT PIN 2 PN-20227
7 SPRING PIN 2 PN-20269B
8 THRUST PLATE PIN 2 179328
9 BUSHING 2 PL-30206
10 GREASE FITTING 2 27662
11 EYE BOLT 2 PN-20226
12 JAM NUT 2 PN-10224AF
13 BUSHING 2 PN-20226A
14 PUSH BAR - 48 IN. FORK 2 1156048/001
15 EXIT ROLLER 2 PN-20220
16 BUSHING 4 PL-20206
17 BUSHING 4 PN-20203
18 LEFT LEVER ARM WITH BUSHING 2 1155938
RIGHT LEVER ARM WITH BUSHING 2 1156047
19 SPRING PIN 4 PN-20269
20 FORK PIN 2 PN-20219
21 LOAD ROLLER WITH BEARINGS (NYLON) 2 PL-20210N-B
22 BALL BEARING 4 PL-20214
23 AXLE ASSEMBLY 2 PL-20215
24 LOCK NUT 2 PL-10218
8
RECYCLING YOUR OLD LIFT-RITE PARTS
Chassis Steel, zinc

Roller suspension Steel, cast iron, zinc
Bushings Brass
Grease fittings Steel
Rollers Nylon, steel
Hydraulic body Cast iron, zinc
Thrust plate Cast iron, zinc
Handle Steel, zinc
Wheel Nylon, steel
Bushings Brass
Hydraulic oil Disposal in accordance with local regulations
Assembly parts Steel, brass, nylon
9
HAND PALLET TRUCK WARRANTY
The Lift-Rite Titan Series Hand Pallet Trucks, Model LCF55 version, are warranted against defects in materials
and workmanship for a period of six (6) months from date of installation.
Components found to be defective by an authorized Lift-Rite Sales and Service Center during the warranty
period will be replaced or repaired as indicated above. Replacement components installed during the defined
period set forth above, are warranted for the balance of the applicable truck warranty period, or 90 days,
whichever is longer. Additionally, freight charges for parts involved in the replacement or repair of a defective
component will be paid by Lift-Rite, provided that the replacement or repair is made by an authorized Lift-Rite
Sales and Service Center. Labor or miscellaneous costs involved in the replacement of any components
determined to be defective are not covered. Local taxes, if any, are excluded.
This warranty is void in the event of defects or damage caused by misuse, abuse, or accident. Any truck used in
an application where the unit is operating in water or subjected to fluid or chemicals is NOT covered under any
warranty.
This warranty does not cover oil leaks, adjustments, or loose hardware.
Lift-Rite reserves the right to make changes and improvements in design without making changes to
previously manufactured vehicles.
Notwithstanding any other language contained herein, this warranty is expressly voided without any further
notice if any modification is made to the Lift-Rite equipment, or if additional components or devices are added
to the Lift-Rite equipment, without prior approval having been granted in writing by Lift-Rite.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY.

THERE ARE NO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
In no event shall Lift-Rite be liable for incidental, special, or consequential damages.
10

1156119B LCF55

Uploaded by

Copyright:

Available Formats

1156119B LCF55

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

1156119B LCF55

Uploaded by

Copyright:

Available Formats

Owner’s Manual, Operating

Instructions Manual, and

To locate your Sales and Service Center, go to www.liftrite.com

To raise the load, push down on NOTE:

CHECK Hydraulic Chassis/ Lifting/

PUSH BAR LINKAGE ADJUSTMENT

ADDING OIL (IF REQUIRED)

CONDITION POSSIBLE CAUSE ACTION

ITEM DESCRIPTION QTY PART NO.

ITEM DESCRIPTION QTY PART NO.

Chassis Steel, zinc

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY.

You might also like