Tpbo Paper-2

10/07/2023, 10:49 https://g06.tcsion.com/CAE/viewHtmlPDFAction.
action
Print
TCSiON CAE

Notations :
1.Options shown in green color and with icon are correct.
2.Options shown in red color and with icon are incorrect.

Question Paper Name : PC22142 CONCERNED SUBJECT TPBO2214
Subject Name : PC22142 CONCERNED SUBJECT TPBO2214
Actual Answer Key : Yes
Calculator : None
Magnifying Glass Required? : No
Ruler Required? : No
Eraser Required? : No
Scratch Pad Required? : No
Rough Sketch/Notepad Required? : No
Protractor Required? : No
Show Watermark on Console? : Yes
Highlighter : No
Auto Save on Console? Yes
Change Font Color : No
Change Background Color : No
Change Theme : No
Help Button : No
Show Reports : No
Show Progress Bar : No
Is this Group for Examiner? : No
Examiner permission : Cant View
Show Progress Bar? : No

CONCERNED SUBJECT
Section type : Online
Enable Mark as Answered Mark for Review and Clear Response : Yes
Maximum Instruction Time : 0
Is Section Default? : null

Question Number : 1 Question Id : 630680265911 Is Question Mandatory : No Calculator : None Response Time : N.A Think Time
: N.A Minimum Instruction Time : 0
Correct Marks : 1
The length of a line measured with a 20 metre chain was found to be 400 metre. Calculate the true length of the line if the chain was 10 cm
too short.
Options :
402 metre
398 metre
396 metre
392 metre

Correct Marks : 1
______ is the main and longest line from which all measurement to demonstrate details of the work are taken.
Options :
Tie line
Chain line
Base line
Check line

https://g06.tcsion.com/CAE/viewHtmlPDFAction.action 1/32
10/07/2023, 10:49 https://g06.tcsion.com/CAE/viewHtmlPDFAction.action
Correct Marks : 1
X is the obstacle to chaining but not ranging. Which of the following CANNOT be X?
Options :
Ponds
Lakes
Marshy land
Hill

Correct Marks : 1
Which of the following is obstacle to both chaining and ranging?
Options :
Ponds
Lakes
Building
Hill

Correct Marks : 1
______ of a line is the horizontal angle which it makes with any arbitrary meridian passing through one of the extremities.
Options :
True bearing
Arbitrary bearing
Magnetic bearing
Whole circle bearing

Correct Marks : 1
If the whole circle bearing is 262° its reduced bearing is ______.
Options :
S82°W
N82°W
N8°W
S8°W

Correct Marks : 1
Which of the following statement is correct?
I. Least count for prismatic compass is 30 seconds.

II. Least count for surveyor compass is 15 minutes.
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
I. Main principle of surveying is work from whole to the part.

II. Check line is a line which joins subsidiary or tie station on the main line.
III. Hill is obstacle to chaining but not ranging.
Options :
Only I
Only II
Only III
I, II and III

Correct Marks : 1
Options :
I-2, II-1, III-3
I-3, II-2, III-1
I-2, II-3, III-1
I-3, II-1, III-2

Question Number : 10 Question Id : 630680265920 Is Question Mandatory : No Calculator : None Response Time : N.A Think
Time : N.A Minimum Instruction Time : 0
Correct Marks : 1
Options :
Only I and II
Only II and III
Only I and III
I, II and III

Correct Marks : 1
Options :
IV, III, II, I
II, III, IV, I
I, II, III, IV
IV, II, I, III

Correct Marks : 1
______ are imaginary lines joining the points of the same height.
Options :
Base line
Check line
Contour line
Tie line

Correct Marks : 1
Which of the following is NOT the method of interpolation of contours?
Options :
By estimation
By arithmetic calculation
By tacheometric method
By graphical method

Correct Marks : 1
______ is a traditional method of surveying that involves measuring distances between points on the ground using a chain or tape measure.
Options :
Plane table surveying
Chain surveying
Theodolite surveying
Total station surveying

Correct Marks : 1
______ the observations are made to those points which will subsequently be used as instrument stations.
Options :
Radiation
Traversing
Intersection
Resection

Correct Marks : 1
Which of the following is the principle of plane table survey?
Options :
Radiation
Ranging
Parallelism
Triangulation

Correct Marks : 1
______ is a method of plane table surveying in which the location of a plane table is unknown.
Options :
Radiation
Resection
Intersection
Traversing

Correct Marks : 1
I. Contour is an imaginary line on the ground joining the points of equal elevation.
II. Vertical distance between any two consecutive contours is called contour elevation.
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
I. City surveys are made in connection with the construction of streets, water supply systems, sewers and other works.
II. Topographical survey are made incident to the fixing of property lines, calculation of land area, on the transfer of land property from
one owner to another.
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
I. Contour gradient is a line lying throughout on the surface of the ground and preserving a constant inclination to the horizontal.
II. Contour lines of different elevations can unite to from one line only in the case of a vertical cliff.
III. Contour line cross a watershed or ridge at right angle.
Options :
Only I
Only II
Only III
I, II and III

Correct Marks : 1
Which of the following is correct pair?
I. Contour gradient : Contour gradient is a line lying throughout on the surface of the ground and preserving a constant inclination to the
horizontal.
II. Resection : It is a method of plane table surveying in which the location of a plane table is unknown.
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
Arrange the following reduced bearing in increasing order by the value of their whole circle bearing?
I. S60°W
II. S50°E
III. N40°E
Options :
I, II, III
III, I, II
III, II, I
II, I, III

Correct Marks : 1
Arrange the following reduced bearing in increasing order by the value of their whole circle bearing?
I. N20°W
II. S20°W
III. N40°E
Options :
III, II, I
I, II, III
II, I, III
III, I, II

Correct Marks : 1
______ rocks are composed of very fine sediments like clay, these rocks are consolidated and have very low porosity and permeability.
Options :
Calcareous
Argillaceous
Siliceous
Plutonic

Correct Marks : 1
______ is a layer of natural stone applied to the walls and when applied it gives an effect such that the wall is made of the natural stone
itself.
Options :
Weathering
Cladding
Dressing of stones
Plastering

Correct Marks : 1
______ is one the decorative and protective methods usually applied on external or internal horizontal walls and surfaces.
Options :
Stone weathering
Stone cladding
Stone veneering
Stone watering

Correct Marks : 1
______ is a construction technique used when a structure with multiple columns and overlapping bases is built. A footing or foundation is
used to transmit a building's weight onto the earth underneath.
Options :
Spread footings
Combined footings
Mat footings
Continuous footings

Correct Marks : 1
______ is a generally applied at basement levels, which restricts the movement of moisture through walls and floors.
Options :
Rafter
Damp Proof Course (DPC)

Stucco
Warping

Correct Marks : 1
I. Spread foundations are foundations at shallow depths of burial where the ground resistance on the sides of the foundation does not
contribute significantly to the bearing resistance.
II. Combined footing is a type of shallow foundation.
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
I. In the construction of a wall when we arrange all the bricks in such a manner that only stretcher is showing then that type of bond is
known as stretcher bond.
II. Pier foundation is a series of vertical pillars or piles that transfer the building load to the soil.
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
I. The method of removal of stones from their natural bed by using different operations is called blasting of stone.
II. Slate belongs to metamorphic rocks.
III. Marble belongs to plutonic rocks.
Options :
Only I
Only II
Only III
I, II and III

Correct Marks : 1
I. Fire brick : These bricks are also called refractory brick

II. High alumina brick : High alumina bricks are built using 40% up to 90% alumina along with superior grade aggregate
III. Light weight hollow brick : These are low density bricks
Options :
Only I and II
Only II and III
Only I and III
I, II and III

Correct Marks : 1
Arrange the following grade of cement in increasing order on the basis of their compressive strength?
I. OPC43
II. OPC33
III. OPC53
Options :
II, I, III
I, II, III
II, III, I
III, I, II

Correct Marks : 1
Arrange the following bricks in increasing order on the basis of their value of crushing strength?
I. First class brick

II. Third class brick
III. Second class brick
Options :
I, II, III
III, II, I
II, III, I
II, I, III

Correct Marks : 1
______ finish consists of rich concrete made with very hard and tough quality coarse aggregate graded from 13 to 240 no. IS sieve.
Options :
Granolithic flooring
Terrazzo flooring
Mosaic flooring
Tiled flooring

Correct Marks : 1
______ is a special type of concrete flooring in which marble chips are used as aggregate and this concrete on polishing with carborundum
stone presents a smooth surface.
Options :
Granolithic flooring
Terrazzo flooring
Mosaic flooring
Tiled flooring

Correct Marks : 1
______ is made of small pieces of broken tiles of china glazed or of cement, or of marble, arranged in different pattern.
Options :
Tiled flooring
Mosaic flooring
Marble flooring
Glass flooring

Correct Marks : 1
______ is basically the modification of a pitched roof and covers large areas of the building.
Options :
Flat roof
Hip roof
Shell roof
Metal roof

Correct Marks : 1
______ slabs provide a lighter and stiffer slab than an equivalent flat slab, reducing the extent of foundations.
Options :
Ribbed
Hardy
Hollow core
Flat

Correct Marks : 1
I. Flat slab floor is a slab floor with or without rectangular drops and supported on columns with or without flared heads.
II. A flat slab may be designed either by direct design method or by equivalent frame method.
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
I. Hardy slab is also called joist slab, or beam and joist slabs.
II. The construction on jack requires centering of 30 to 40 mm thick segmental piece of timber, with chord length equal to the span of the
arch and conforming to the soffit.
III. Reinforced brickwork is a typical type of construction in which the compressive strength of bricks is utilised to bear the compressive
stresses.
Options :
Only I and II
Only II and III
Only I and III
I, II and III

Correct Marks : 1
Options :
I-2, II-3, III-1
I-3, II-2, III-1
I-1, II-3, III-2
I-2, II-1, III-3

Correct Marks : 1
I. Purlins : They are beams spanning between trusses

II. Fan roof truss : They are form of fink trusses
III. Warren truss : It is used for sloppy roof
Options :
Only I and II
Only II and III
Only I and III
I, II and III

Correct Marks : 1
Arrange the following weight of roof covering in increasing order for different roof covering given below.
I. Galvanised corrugated sheeting

II. Corrugated A.C.C Sheeting
III. Slates
Options :
I, II, III
III, II, I
II, III, I
II, I, III

Correct Marks : 1
Arrange the following weights of purlins for different roofs in increasing order.
I. Slate roof
II. Corrugated sheeting
III. Glazed roof
Options :
I, II, III
III, II, I
II, III, I
II, I, III

Correct Marks : 1
______ is the center to center distance between two adjacent rivets in the same row, measured parallel to the seam of edge of the plate.
Options :
Pitch
Fullering
Butt
Eillet

Correct Marks : 1
______ is the operation of burring down the whole end thickness of plates and it is operated by hammering or compressed air.
Options :
Caulking
Fullering
Riveting
Margin

Correct Marks : 1
______ is a technique in which two pieces of material are joined simply placing their ends together without any special shaping.
Options :
Edge joints
Butt joint
Lap joint
Tee joint

Correct Marks : 1
______ is a joint in which the members overlap and it can be used to join wood, plastic or metal.
Options :
Edge joints
Butt joint
Lap joint
Tee joint

Correct Marks : 1
Options :

Correct Marks : 1
If nominal diameter of the rivet is 24 mm, then what is the value of thickness of plate by using Unwin’s formula?
Options :
20 mm
16 mm
10 mm
25 mm

Correct Marks : 1
______ this irrigation system, water is applied to a completely level or dead level area enclosed by dikes or boarders.
Options :
Check basin irrigation
Furrow irrigation
Border irrigation
Drip irrigation

Correct Marks : 1
I. Fertigation is the process of application of water soluble solid fertilizer or liquid fertilizers through drip irrigation systems.
II. Furrow irrigation minimizes the use of water and fertilizer by allowing water to drip slowly to the root of plants.
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
I. Margin is the distance between row of rivets measured perpendicular to the seam.
II. Diagonal pitch is the center to center distance between two rivets placed diagonally in two rows in the same plate.
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
I. Blistering is a raised portion of the surface protruding not more than one millimeter above the surface.
II. The process of joining two or more than two parts of machine or structure by means of rivets is known as riveting.
III. Structural rivets are used in the fabrication of boiler to join thick plates together.
Options :
Only I and II
Only II and III
Only I and III
I, II and III

Correct Marks : 1
Options :
I-2, II-3, III-1
I-3, II-2, III-1
I-1, II-3, III-2
I-2, II-1, III-3

Correct Marks : 1
I. Dunt : A hairline fracture extending through or into the body of the article.
II. Warpage : Distortion of original shape during manufacturing process.
III. Wavy finish : A defect in the glaze finish having the appearance of numerous runs in the glaze irregular or molted.
Options :
Only I and II
Only II and III
Only I and III
I, II and III

Correct Marks : 1
Which of the following is a type of sprinkler irrigation method?
I. Rotating Head
II. Perforated Pipe
III. Corrugation
Options :
Only I and III
Only II and III
Only I and II
I, II and III

Correct Marks : 1
Arrange the following values of thickness of plate in increasing order for different values of nominal diameter of rivet?
I. d = 30 mm
II. d = 40 mm
III. d = 54 mm
Options :
I, II, III
III, II, I
II, III, I
II, I, III

Correct Marks : 1
______ is the separation between two rails and it is the distance between the inner faces of the two rails.
Options :
Fastners
Ballast
Gauge
Sleeper

Correct Marks : 1
______ is a measure of number of sleeper provided per unit.
Options :
Rail density
Sleeper density
Railway density
Track density

Correct Marks : 1
______ of rail is the movement of rails in forward direction of dominate traffic.
Options :
Hogged
Creep
Corroded
Buckling

Correct Marks : 1
______ of rail occurs when the gap at expansion joint is inadequate and it can cause derailment.
Options :
Hedging
Blasting
Cracking
Buckling

Correct Marks : 1
______ is the name given to the material placed between the sleeper and the foundation.
Options :
Rail fastening
Ballast
Tie plate
Spikes

Correct Marks : 1
According to Indian railway, in coning of wheel the tread or rim of wheels of railway vehicles is made in the shape of a cone with the slope
of about ______.
Options :
1 in 30
1 in 10
1 in 20
1 in 40

Correct Marks : 1
______ rails are used in the construction of the track, placed parallel to regular running rail to keep the wheels of rolling stock in alignment
to pavement derailment.
Options :
Check
Stock
Double head
Flat foot

Correct Marks : 1
I. A fish plate is the fastening that connects two rails ends.

II. Check rail are additional rails not intended for movement of wheels directly on them, but as checks and guards to the train movement at
selected locations.
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
I. State highway connect to the national highway of neighbouring states, district headquarter and main cities within the states.
II. Major district road serve rural area by connecting them to market places, block development headquarters and other points of interest.
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
I. Arterial roads are intended for complete traffic on a continuous route with strong traffic mobility.
II. A turnout is an assembly of various components whereby a train running on one track may be diverted to another.
III. A scissor crossing consists of two cross over overlapping each other.
Options :
Only I and II
Only II and III
Only I and III
I, II and III

Correct Marks : 1
Options :
Only I and II
Only II and III
Only I and III
I, II and III

Correct Marks : 1
Options :
I-2, II-3, III-1
I-3, II-1, III-2
I-1, II-3, III-2
I-2, II-1, III-3

Correct Marks : 1
Arrange the following gauges in increasing order of their width.
I. Broad gauge
II. Meter gauge
III. Narrow gauge
Options :
I, II, III
III, II, I
II, III, I
II, I, III

Correct Marks : 1
Arrange the following road types in increasing order for the value of vehicle per day?
I. Medium traffic roads

II. Road with heavy traffic
III. Less traffic road
Options :
I, II, III
III, II, I
III, I, II
II, I, III

Correct Marks : 1
Which of the following is correct formula for finding representative fraction?
Options :

Correct Marks : 1
______ represents three units of measurements such as metres, decimeters and centimetres or two units and a fraction of its second unit.
Options :
Ratio scale
Diagonal scale
Retrograde scale
Interval scale

Correct Marks : 1
______ are plain scales which have a common representative fraction but graduated in units of different system of measurements.
Options :
Ratio scale
Diagonal scale
Comparative scale
Retrograde scale

Correct Marks : 1
If one centimeter on drawing represents two metres actual distance of the object, then what is the value of representation fraction?
Options :

Correct Marks : 1
If a distance of one kilometer on ground is represented by one meter on the drawing, then what is the value of representation fraction?
Options :

Correct Marks : 1
I. Plain scales are the ones which are used to show two units of measurement such as metres and decimeters, kilometers and hectometers
etc.
II. SI unit of representative fraction is meter.
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
I. Scale is defined as the ratio of map distance between two points and ground distance between the same points.
II. Representative fraction shows the relationship between the map distance and the corresponding ground distance in unit of length.
III. Diagonal scales are drawn for greater precision or higher degree of accuracy.
Options :
Only I and II
Only II and III
Only I and III
I, II and III

Correct Marks : 1
Options :
Only I and II
Only II and III
Only I and III
I, II and III

Correct Marks : 1
Arrange the following scale in increasing order for the value of their representative fraction?
I. 1 cm = 100 m
II. 1 m = 100 km
III. 1 cm = 10 m
Options :
I, II, III
III, II, I
III, I, II
II, I, III

Correct Marks : 1
The two planes employed for the purpose of orthographic projections are called ______.
Options :
Principle plane of projection
Vertical plane of projection
Horizontal plane of projection
Frontal plane of projection

Correct Marks : 1
______ is the plane onto which the top view of the multi-view drawing is projected and top-view of an object shows the width and depth
dimension.
Options :
Principle plane of projection
Vertical plane of projection
Horizontal plane of projection
Planar projection

Correct Marks : 1
______ is a view of an object showing the important features, which may be chosen from the point of view of design, assembly, sales,
services or maintenance.
Options :
Exploded view
True view
Principal view
Pictorial view

Correct Marks : 1
______ is the view of an object that lie on a plane parallel to the projection plane; geometrically similar to the corresponding features of
the object.
Options :
Exploded view
True view
Principal view
Pictorial view

Correct Marks : 1
______ is a way of representing a 3D object by using several 2D views of the object.
Options :
Oblique projection
Orthographic projection
Isometric projection
Perspective projection

Correct Marks : 1
Which of the following statement is correct for first angle projection?
I. The object is kept in the first quadrant

II. The objection lies between the observer and the plane of projection
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
Which of the following statement is correct for third angle projection?
I. The plane of projection lies between the observer and the object.
II. This method of projection is used in U.S.A.
III. The plane of projection is assumed to be non-transparent.
Options :
Only I and II
Only II and III
Only I and III
I, II and III

Correct Marks : 1
Which of the following is correct pair for method of projection with their destinations?
I. Oblique : An oblique projection is a parallel projection in which the lines of sight are not perpendicular to the projection plane.
II. Isometric Projection : It is a method for visually representing three dimensional objects in two dimension in technical and engineering
drawing.
III. Perspective projection : It is a nonlinear projection where three dimensional objects are projected on a picture plane.
Options :
Only I and II
Only II and III
Only I and III
I, II and III

Correct Marks : 1
______ is a type of door where upper part is glazed, to admit light.
Options :
Flush door
Folding door
Sash door
Pocket door

Correct Marks : 1
______ is a horizontal piece (as a timber) that forms the lowest part of a supporting structure in a door frame.
Options :
Frame
Sill
Transom
Panel

Correct Marks : 1
In ______ doors, the shutters are hung from the door frame by means of hinges or butt fixed to one side of the shutter so that they swing on
vertical axis.
Options :
rolling
swinging
revolving
collapsible

Correct Marks : 1
______ doors are extensively used where frequent opening and closing of a door is to be avoided due to heavy foot traffic eg. Fish market,
public buildings tanks and hotel etc.
Options :
Rolling
Swinging
Revolving
Collapsible

Correct Marks : 1
______ type of door allows sufficient amount of air circulation even when closed and at the same time maintain privacy.
Options :
Louvered door
Wire gauged door
Hollow metal door
Collapsible door

Correct Marks : 1
I. Steel tape is used for large measurements, such as marking on boards and checking the overall dimensional of work.
II. Try square is used for marking and testing the straightness and squareness of planed surfaces.
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
______ has a narrow, longer and stronger tampering blade, which is used for heavy works and it is used for radius cutting
Options :
Rip saw
Tenon saw
Compass saw
Hand saw

Correct Marks : 1
Options :
I-2, II-3, III-1
I-3, II-1, III-2
I-1, II-3, III-2
I-2, II-1, III-3

Correct Marks : 1
Arrange the following doors type in increasing order by their normal areas?
I. Internal doors for residential building

II. Doors in garages
III. Doors in public building (for example a hospital)
Options :
I, III, II
III, II, I
III, I, II
II, I, III

Correct Marks : 1
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
______ is a simple webbed truss design that provides the most economical roof solution for roof structures.
Options :
Fink roof tress
Howe roof truss
Queen post roof truss
King post roof truss

Correct Marks : 1
______ is a truss bridge consisting of chords, verticals and diagonals whose vertical members are in tension and whose diagonal members
are in compression.
Options :
Fink roof truss
Howe roof truss
Queen post roof truss
King post roof truss

Correct Marks : 1
______ windows are made of shutters which move horizontally or vertically on small roller bearings.
Options :
Casement window
Sliding window
Glazed window
Louvered window

Correct Marks : 1
______ consists of two straight flights of steps with usually a level landing where the direction of travels changes by 180°.
Options :
Straight stairs
Open well stairs
Dog legged stairs
Geometrical stairs

Correct Marks : 1
______ consists of two or more straight flights with a central well and there could be quarter landings or winders at the corner.
Options :
Straight stairs
Open well stairs

Dog legged stairs
Spiral stairs

Correct Marks : 1
I. The uppermost line of members that extend from one support to the other through the apex is called top chord.
II. The rise of a roof truss is the vertical distance measured from the apex to the line joining supports.
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
I. The ratio of the rise to the span is called bay of a roof truss.
II. The sheathing are coverings of boards or reinforced concrete and they provide support for the roof covering.
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
I. The bottom edges of an inclined roof surface or a pitched roof is termed as eaves.
II. King post truss is also a wooden truss and it is found suitable for span upto 10 cm.
III. Pratt truss is a truss having vertical members between the upper and lower members and diagonal members sloping toward the center.
Options :
Only I and II
Only II and III
Only I and III
I, II and III

Correct Marks : 1
Options :
I-2, II-3, III-1
I-3, II-2, III-1
I-1, II-3, III-2
I-2, II-1, III-3

Correct Marks : 1
As per the standards of ventilation, arrange the following buildings in increasing order by their value of air changes to be provided per
hour.
I. Office generally
II. Restaurant
III. Kitchens
Options :
I, II, III
III, II, I
III, I, II
II, I, III

Correct Marks : 1
I. King Post Spans upto 18 metres.

II. Queen Post Spans upto 25 metres.
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
Arrange the following instruments in increasing order on the basic of their least count.
I. Prismatic compass
II. Vernier theodolite
III. Surveyor compass
Options :
I, II, III
III, II, I
III, I, II
II, III, I

Correct Marks : 1
______ is a drawing in which a three dimensional object is represented in two dimensions.
Options :
Silhouette drawing
Orthographic drawing
Perspective drawing
Line drawing

Correct Marks : 1
______ represented as a view of an object (actual or imagined) as it would be seen by an observer who looks at the object either in a
chosen direction or from a selected point of view.
Options :
Pictorial drawing
Caricature drawing
Sketch drawing
Line drawing

Correct Marks : 1
______ is a method of graphic representation of three-dimensional object.
Options :
Sketch drawing
Isometric drawing
Line drawing

Correct Marks : 1
______ is a technique that gives the illusion of spatial depth, or perspective, to drawing and painting.
Options :
Perspective drawing
Isometric drawing
Line drawing

Correct Marks : 1
In India, what is the dimensions (cm) for AO paper size?
Options :

Correct Marks : 1
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
Options :
Only I and II
Only II and III
Only I and III
I, II and III

Correct Marks : 1
Options :
I-2, II-3, III-1
I-3, II-1, III-2
I-1, II-3, III-2
I-2, II-1, III-3

Correct Marks : 1
Which of the following is correct pair for drawing equipment with their definition?
I. Drawing board : It is rectangular in shape and is made of strips of well-seasoned soft wood.
II. Protractor : It is simple measuring instrument that is used to measure angles.
III. Scale : It is actually a measuring stick, available in a variety of shapes and sizes.
Options :
Only I and II
Only II and III
Only I and III
I, II and III

Correct Marks : 1
______ lines also are continuous thin lines and they extend by about 3 mm key and the dimension lines.
Options :
Dimension
Projection
Hatching
Pointer

Correct Marks : 1
______ are drawn to indicate the axes of cylindrical, conical or spherical objects or details, and also to show the centers of circle and arcs.
Options :
Projection line
Center line
Hidden line
Cutting plane line

Correct Marks : 1
______ are continuous thick or wide lines along which the prints are trimmed.
Options :
Margin line
Outline
Dimension line
Construction line

Correct Marks : 1
Options :
Long break line
Cutting planes
Line showing permissible of surface treatment
Movable parts

Correct Marks : 1
Options :
Pitch circle of holes
Cutting planes
Long break line
Hidden outlies

Correct Marks : 1
I. Lines drawn to represent visible edges and surface boundaries of objects are called outlines or principle lines.
II. Long break lines are thin ruled lines with short zigzags within them and they are shown to show long breaks.
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
I. Chain thick lines are used to indicate special treatment on the surface.
II. The surface of a sphere can be approximately developed by zone method and Lune method.
III. Octahedron is a regular polyhedral consisting of eight equal faces, each an equilateral triangle.
Options :
Only I and II
Only II and III
Only I and III
I, II and III

Correct Marks : 1
Options :
I-2, II-3, III-1
I-3, II-2, III-1
I-1, II-3, III-2
I-2, II-1, III-3

Correct Marks : 1
Arrange the following chains in increasing order on the basis of length of one link present in chain?
I. Engineering chain
II. Meter chain (30 m)
III. Gunter chain
Options :
I, II, III
III, II, I
III, I, II
II, III, I

Correct Marks : 1
Options :
I, II, III
III, II, I
III, I, II
II, III, I

Correct Marks : 1
______ is a quadrilateral in which all the sides are equal and the angles are at right angle.
Options :
Parallelogram
Rectangle
Square
Rhombus

Correct Marks : 1
______ a plot shape with four straight sides, one pair of opposite sides being parallel and the other pair not parallel.
Options :
Trapezoid
Parallelogram
Rectangle
Square

Correct Marks : 1
______ is a quadrilateral in which all the sides are equal and the angle angles are not at right angles.
Options :
Parallelogram
Rectangle
Square
Rhombus

Correct Marks : 1
______ is a curve generated by a point moving so that at any position the sum of its distance from two fix point (called Foci) is a constant
and is equal to the major diameter.
Options :
Sphere
Ellipse
Cone
Cylinder

Correct Marks : 1
______ is a quadrilateral in which opposite sides are parallel.
Options :
Trapezium
Parallelogram
Rectangle
Square

Correct Marks : 1
I. A scalene triangle has none of its sides and angles equal.

II. A polygon is a plane figure bonded by more than four straight lines and containing more than four angles.
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
I. If all the sides and angles of a polygon are equal then it is called a regular polygon.
II. If all the sides and angles are unequal, then it is called an irregular polygon.
III. Polygons are named according to the number of their sides and angles.
Options :
Only I and II
Only II and III
Only I and III
I, II and III

Correct Marks : 1
Which of the following is correct pair for the polygon by their number of sides present in polygon?
I. Heptagon : 5
II. Nonagon : 9
III. Pentagon : 6
Options :
Only I and II
Only II and III
Only I and III
I, II and III

Correct Marks : 1
Which of the following is correct pair for the magnetic lines given with their definitions?
I. Agonic line : The line joining the place of zero declaration

II. Isoclinic line : The line joining the place of the same dip
III. Aclinic : The line joining the place of zero dip
Options :
Only I and II
Only II and III
Only I and III
I, II and III

Correct Marks : 1
Which of the following Indian Standard is related with Lettering?
Options :
IS : 9609-2001
IS : 9118-1996
IS : 8041-1998
IS : 6511-1991

Correct Marks : 1
As per the recommendation of Bureau of Indian Standards, ______ letters for use in engineering drawing.
Options :
double-stroke
single-stroke
triple-stroke
four-stroke

Correct Marks : 1
Which of the following formula describes the length of an unusual scale drawn?
Options :

Correct Marks : 1
On a scale, 20 cm line represents 100 meters length of the object. What is will be the R.F. of this scale?
Options :

Correct Marks : 1
Singles stroke letters are described into type on basis of their ______.
Options :
thickness of lines
spacing between letters
height
minimum spacing between word

Correct Marks : 1
Which of the following is correct regarding the single stroke inclined letters?
I. They lean to the right.

II. Their slope is 75 degrees from the horizontal.
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
Which of the following pair of lettering type single stroke letter – number of parts in which height is divided is correct?
I. Lettering ‘A’ type – 10

II. Lettering ‘B’ type – 14
Options :
Only I
Only II
Both I and II
Neither I nor II

Correct Marks : 1
In engineering drawings, which of the following statement is correct regarding lettering?
I. The main titles are generally written in 6 mm to 8 mm size

II. Sub-titles are generally written in 3 mm to 6 mm size
III. Notes, dimension figures etc. in 3 mm to 5 mm size
Options :
Only I and II
Only II and III
Only I and III
I, II and III

Correct Marks : 1
Options :
1 – II, 2 – III, 3 – I
1 – I, 2 – III, 3 – II
1 – III, 2 – II, 3 – I
1 – III, 2 – I, 3 – II

Tpbo Paper-2

Uploaded by

Copyright:

Available Formats

Tpbo Paper-2

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tpbo Paper-2

Uploaded by

Copyright:

Available Formats

10/07/2023, 10:49 https://g06.tcsion.com/CAE/viewHtmlPDFAction.

I. Least count for prismatic compass is 30 seconds.

I. Main principle of surveying is work from whole to the part.

Damp Proof Course (DPC)

I. Fire brick : These bricks are also called refractory brick

I. First class brick

I. Purlins : They are beams spanning between trusses

I. Galvanised corrugated sheeting

I. A fish plate is the fastening that connects two rails ends.

I. Medium traffic roads

I. The object is kept in the first quadrant

I. Internal doors for residential building

Open well stairs

I. King Post Spans upto 18 metres.

I. A scalene triangle has none of its sides and angles equal.

I. Agonic line : The line joining the place of zero declaration

I. They lean to the right.

I. Lettering ‘A’ type – 10

I. The main titles are generally written in 6 mm to 8 mm size

You might also like