SAFETY DATA SHEET

THE DOW CHEMICAL COMPANY

Product name: ACULYN™ Siltouch Rheology Modifier Issue Date: 06/28/2022

Print Date: 06/29/2022
THE DOW CHEMICAL COMPANY encourages and expects you to read and understand the entire
(M)SDS, as there is important information throughout the document. We expect you to follow the
precautions identified in this document unless your use conditions would necessitate other appropriate
methods or actions.

1. IDENTIFICATION
Product name: ACULYN™ Siltouch Rheology Modifier

Recommended use of the chemical and restrictions on use

Identified uses: Cosmetics

COMPANY IDENTIFICATION
THE DOW CHEMICAL COMPANY
2211 H.H. DOW WAY
MIDLAND MI 48674
UNITED STATES

Customer Information Number: 800-258-2436

SDSQuestion@dow.com

EMERGENCY TELEPHONE NUMBER

24-Hour Emergency Contact: CHEMTREC +1 800-424-9300
Local Emergency Contact: 800-424-9300

2. HAZARDS IDENTIFICATION
Hazard classification
GHS classification in accordance with the OSHA Hazard Communication Standard (29 CFR
1910.1200)
Not a hazardous substance or mixture.

Other hazards
No data available

3. COMPOSITION/INFORMATION ON INGREDIENTS

Chemical nature: Organic compound emulsion

This product is a mixture.
Component CASRN Concentration

General Business
® ™ Trademark of The Dow Chemical Company ("Dow") or an affiliated Page 1 of 13
company of Dow
Product name: ACULYN™ Siltouch Rheology Modifier Issue Date: 06/28/2022

Ethoxylated branched C11-14, C13-rich 78330-21-9 >= 3.0 - <= 5.0 %

alcohols

4. FIRST AID MEASURES

Description of first aid measures
General advice:
First Aid responders should pay attention to self-protection and use the recommended protective
clothing (chemical resistant gloves, splash protection). If potential for exposure exists refer to Section
8 for specific personal protective equipment.

Inhalation: Move person to fresh air and keep comfortable for breathing; consult a physician.

Skin contact: Wash off with plenty of water. Seek first aid or medical attention as needed. If molten
material comes in contact with the skin, do not apply ice but cool under ice water or running stream of
water. DO NOT attempt to remove the material from skin. Removal could result in severe tissue
damage. Seek medical attention immediately. Suitable emergency safety shower facility should be
immediately available.

Eye contact: Flush eyes thoroughly with water for several minutes. Remove contact lenses after the
initial 1-2 minutes and continue flushing for several additional minutes. If effects occur, consult a
physician, preferably an ophthalmologist.

Ingestion: Rinse mouth with water. No emergency medical treatment necessary.

Most important symptoms and effects, both acute and delayed:

Aside from the information found under Description of first aid measures (above) and Indication of
immediate medical attention and special treatment needed (below), any additional important
symptoms and effects are described in Section 11: Toxicology Information.

Indication of any immediate medical attention and special treatment needed

Notes to physician: If burn is present, treat as any thermal burn, after decontamination. No specific
antidote. Treatment of exposure should be directed at the control of symptoms and the clinical
condition of the patient.

5. FIREFIGHTING MEASURES
Extinguishing media

Suitable extinguishing media: Water spray. Alcohol-resistant foam. Carbon dioxide (CO2).
Dry chemical.

Unsuitable extinguishing media: None known..

Special hazards arising from the substance or mixture

Hazardous combustion products: Carbon oxides. Nitrogen oxides (NOx). Metal oxides.
Sulphur oxides. Silicon oxides.

General Business
Page 2 of 13
Product name: ACULYN™ Siltouch Rheology Modifier Issue Date: 06/28/2022

Unusual Fire and Explosion Hazards: Exposure to combustion products may be a hazard to
health.. Dried product can burn.. Material can splatter above 100C/212F..

Advice for firefighters

Fire Fighting Procedures: Use water spray to cool unopened containers.. Evacuate area..
Collect contaminated fire extinguishing water separately. This must not be discharged into
drains.. Fire residues and contaminated fire extinguishing water must be disposed of in
accordance with local regulations.. Contain fire water run-off if possible. Fire water run-off, if
not contained, may cause environmental damage..
Use extinguishing measures that are appropriate to local circumstances and the surrounding
environment. Remove undamaged containers from fire area if it is safe to do so.

Special protective equipment for firefighters: Wear self-contained breathing apparatus for
firefighting if necessary.. Use personal protective equipment..

6. ACCIDENTAL RELEASE MEASURES

Personal precautions, protective equipment and emergency procedures: Material can create
slippery conditions. Follow safe handling advice and personal protective equipment
recommendations.

Environmental precautions: Do not release the product to the aquatic environment above defined
regulatory levels Prevent further leakage or spillage if safe to do so. Prevent spreading over a wide
area (e.g. by containment or oil barriers). Retain and dispose of contaminated wash water. Local
authorities should be advised if significant spillages cannot be contained.

Methods and materials for containment and cleaning up: Soak up with inert absorbent material.
Clean up remaining materials from spill with suitable absorbant. Local or national regulations may
apply to releases and disposal of this material, as well as those materials and items employed in the
cleanup of releases. You will need to determine which regulations are applicable. For large spills,
provide dyking or other appropriate containment to keep material from spreading. If dyked material can
be pumped, store recovered material in appropriate container.
See sections: 7, 8, 11, 12 and 13.

7. HANDLING AND STORAGE

Precautions for safe handling: Take care to prevent spills, waste and minimize release to the
environment. Handle in accordance with good industrial hygiene and safety practice. Monomer
vapors can be evolved when material is heated during processing operations. See SECTION 8, for
types of ventilation required. CONTAINERS MAY BE HAZARDOUS WHEN EMPTY. Since emptied
containers retain product residue follow all (M)SDS and label warnings even after container is emptied.
Use only with adequate ventilation. See Engineering measures under EXPOSURE
CONTROLS/PERSONAL PROTECTION section.

Conditions for safe storage: Keep in properly labelled containers. Store in accordance with the
particular national regulations.

Do not store with the following product types: Strong oxidizing agents.
Unsuitable materials for containers: None known.

General Business
Page 3 of 13
Product name: ACULYN™ Siltouch Rheology Modifier Issue Date: 06/28/2022

8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Control parameters
If exposure limits exist, they are listed below. If no exposure limits are displayed, then no values are
applicable.

Exposure controls
Engineering controls: Use local exhaust ventilation, or other engineering controls to maintain
airborne levels below exposure limit requirements or guidelines. If there are no applicable exposure
limit requirements or guidelines, general ventilation should be sufficient for most operations. Local
exhaust ventilation may be necessary for some operations.

Individual protection measures

Eye/face protection: Use safety glasses (with side shields). When handling hot material:
Use chemical goggles. Wear a face-shield which allows use of chemical goggles, or wear a
full-face respirator, to protect face and eyes when there is any likelihood of splashes.
Skin protection
Hand protection: Use gloves chemically resistant to this material. Use gloves with
insulation for thermal protection, when needed. Examples of preferred glove barrier
materials include: Butyl rubber. Natural rubber ("latex"). Neoprene. Nitrile/butadiene
rubber ("nitrile" or "NBR"). Ethyl vinyl alcohol laminate ("EVAL"). Polyvinyl chloride
("PVC" or "vinyl"). Avoid gloves made of: Polyvinyl alcohol ("PVA"). NOTICE: The
selection of a specific glove for a particular application and duration of use in a
workplace should also take into account all relevant workplace factors such as, but
not limited to: Other chemicals which may be handled, physical requirements
(cut/puncture protection, dexterity, thermal protection), potential body reactions to
glove materials, as well as the instructions/specifications provided by the glove
supplier.
Other protection: Use protective clothing chemically resistant to this material.
Selection of specific items such as face shield, boots, apron, or full body suit will
depend on the task. When handling hot material, protect skin from thermal burns.
Selection of specific items will depend on the operation.
Respiratory protection: Respiratory protection should be worn when there is a potential to
exceed the exposure limit requirements or guidelines. If there are no applicable exposure limit
requirements or guidelines, wear respiratory protection when adverse effects, such as
respiratory irritation or discomfort have been experienced, or where indicated by your risk
assessment process. For most conditions, no respiratory protection should be needed;
however, if handling at elevated temperatures without sufficient ventilation, use an approved
air-purifying respirator.
The following should be effective types of air-purifying respirators: Organic vapor cartridge.

9. PHYSICAL AND CHEMICAL PROPERTIES

Appearance
Physical state viscous liquid
Color White to light yellow
Odor aliphatic
Odor Threshold No data available
pH 5-8

General Business
Page 4 of 13
Product name: ACULYN™ Siltouch Rheology Modifier Issue Date: 06/28/2022

Melting point/range < 5 °C ( < 41 °F)

Freezing point No data available
Boiling point (760 mmHg) > 100 °C ( > 212 °F)
Flash point closed cup >101 °C ( 214 °F)
Evaporation Rate (Butyl Acetate No data available
= 1)
Flammability (solid, gas) Not applicable
Flammability (liquids) Ignitable (see flash point)
Lower explosion limit No data available
Upper explosion limit No data available
Vapor Pressure 2.3 kPa
Relative Vapor Density (air = 1) No data available
Relative Density (water = 1) 1 - 1.2
Water solubility No data available
Partition coefficient: n- No data available
octanol/water
Auto-ignition temperature No data available
Decomposition temperature > 150 °C (> 302 °F)
Dynamic Viscosity 1,000 mPa.s
Kinematic Viscosity No data available
Explosive properties Not explosive
Oxidizing properties The substance or mixture is not classified as oxidizing.
Solubility in other solvents
completely miscible
Molecular weight No data available
Particle size Not applicable

NOTE: The physical data presented above are typical values and should not be construed as a
specification.

10. STABILITY AND REACTIVITY

Reactivity: Not classified as a reactivity hazard.

Chemical stability: Stable under normal conditions.

Possibility of hazardous reactions: Can react with strong oxidizing agents.

Conditions to avoid: None known.

Incompatible materials: Avoid contact with oxidizing materials.

Hazardous decomposition products:

Decomposition products can include and are not limited to: Formaldehyde.

General Business
Page 5 of 13
Product name: ACULYN™ Siltouch Rheology Modifier Issue Date: 06/28/2022

11. TOXICOLOGICAL INFORMATION

Toxicological information appears in this section when such data is available.

Information on likely routes of exposure

Inhalation, Eye contact, Skin contact, Ingestion.

Acute toxicity (represents short term exposures with immediate effects - no chronic/delayed
effects known unless otherwise noted)

Acute Toxicity Endpoints:

Not classified based on available information.

Acute oral toxicity

Information for the Product:

Very low toxicity if swallowed. Harmful effects not anticipated from swallowing small
amounts.

As product: Single dose oral LD50 has not been determined.

Based on information for component(s):

LD50, Rat, > 5,000 mg/kg Estimated.

Information for components:

Ethoxylated branched C11-14, C13-rich alcohols

Acute toxicity estimate, 500 mg/kg Expert judgement

Acute dermal toxicity

Information for the Product:

Prolonged skin contact is unlikely to result in absorption of harmful amounts.

As product: The dermal LD50 has not been determined.

Based on information for component(s):

LD50, Rabbit, > 2,000 mg/kg Estimated.

Information for components:

Ethoxylated branched C11-14, C13-rich alcohols

The dermal LD50 has not been determined.

Acute inhalation toxicity

Information for the Product:

Brief exposure (minutes) is not likely to cause adverse effects. Vapor from heated material
may cause respiratory irritation.

General Business
Page 6 of 13
Product name: ACULYN™ Siltouch Rheology Modifier Issue Date: 06/28/2022

As product: The LC50 has not been determined.

Information for components:

Ethoxylated branched C11-14, C13-rich alcohols

The LC50 has not been determined.

Skin corrosion/irritation

Not classified based on available information.

Information for the Product:

Based on information for component(s):

Brief contact may cause slight skin irritation with local redness.
Under normal processing conditions, material is heated to elevated temperatures; contact with
the material may cause thermal burns.

Information for components:

Ethoxylated branched C11-14, C13-rich alcohols

For similar material(s):
Prolonged contact may cause slight skin irritation with local redness.

Serious eye damage/eye irritation

Not classified based on available information.

Information for the Product:

Based on testing for product(s) in this family of materials:

May cause slight eye irritation.

Information for components:

Ethoxylated branched C11-14, C13-rich alcohols

For similar material(s):
May cause severe irritation with corneal injury which may result in permanent impairment of
vision, even blindness. Chemical burns may occur.

Sensitization

For skin sensitization:

Not classified based on available information.

For respiratory sensitization:

Not classified based on available information.

Information for the Product:

Based on information for component(s):

For skin sensitization:
Did not cause allergic skin reactions when tested in guinea pigs.

For respiratory sensitization:

General Business
Page 7 of 13
Product name: ACULYN™ Siltouch Rheology Modifier Issue Date: 06/28/2022

No relevant data found.

Information for components:

Ethoxylated branched C11-14, C13-rich alcohols

For similar material(s):
For skin sensitization:
Did not cause allergic skin reactions when tested in humans.

For respiratory sensitization:

No relevant data found.

Specific Target Organ Systemic Toxicity (Single Exposure)

Not classified based on available information.

Information for the Product:

Available data are inadequate to determine single exposure specific target organ toxicity.

Information for components:

Ethoxylated branched C11-14, C13-rich alcohols

Available data are inadequate to determine single exposure specific target organ toxicity.

Aspiration Hazard

Not classified based on available information.

Information for the Product:

Based on physical properties, not likely to be an aspiration hazard.

Information for components:

Ethoxylated branched C11-14, C13-rich alcohols

Based on available information, aspiration hazard could not be determined.

Chronic toxicity (represents longer term exposures with repeated dose resulting in
chronic/delayed effects - no immediate effects known unless otherwise noted)

Specific Target Organ Systemic Toxicity (Repeated Exposure)

Not classified based on available information.

Information for the Product:

Based on available data for the component(s), repeated exposures are not anticipated to cause
significant adverse effects.

Information for components:

Ethoxylated branched C11-14, C13-rich alcohols

No relevant data found.

General Business
Page 8 of 13
Product name: ACULYN™ Siltouch Rheology Modifier Issue Date: 06/28/2022

Carcinogenicity

Not classified based on available information.

Information for the Product:

Contains a component(s) which did not cause cancer in long-term animal studies which used
routes of exposure considered relevant to industrial handling.

Information for components:

Ethoxylated branched C11-14, C13-rich alcohols

No relevant data found.

Teratogenicity

Not classified based on available information.

Information for the Product:

Contains component(s) which did not cause birth defects or any other fetal effects in lab
animals.

Information for components:

Ethoxylated branched C11-14, C13-rich alcohols

No relevant data found.

Reproductive toxicity

Not classified based on available information.

Information for the Product:

Contains component(s) which did not interfere with reproduction in animal studies.

Information for components:

Ethoxylated branched C11-14, C13-rich alcohols

No relevant data found.

Mutagenicity

Not classified based on available information.

Information for the Product:

In vitro genetic toxicity studies were negative for component(s) tested. Genetic toxicity studies
in animals were negative for component(s) tested.

Information for components:

Ethoxylated branched C11-14, C13-rich alcohols

No relevant data found.

General Business
Page 9 of 13
Product name: ACULYN™ Siltouch Rheology Modifier Issue Date: 06/28/2022

12. ECOLOGICAL INFORMATION

Ecotoxicological information appears in this section when such data is available.

Toxicity

Ethoxylated branched C11-14, C13-rich alcohols

Acute toxicity to fish
Material is moderately toxic to aquatic organisms on an acute basis (LC50/EC50 between 1
and 10 mg/L in the most sensitive species tested).
Based on data from similar materials
LC50, Oncorhynchus mykiss (rainbow trout), 96 Hour, 5.6 mg/l

Acute toxicity to aquatic invertebrates

Based on data from similar materials
EC50, Daphnia magna (Water flea), 48 Hour, > 1 - 10 mg/l

Acute toxicity to algae/aquatic plants

Based on data from similar materials
EC50, 96 Hour, > 1 - 10 mg/l

Chronic toxicity to fish

Based on data from similar materials
NOEC, Lepomis macrochirus (Bluegill sunfish), 30 d, > 0.33 mg/l

Chronic toxicity to aquatic invertebrates

Based on data from similar materials
NOEC, Daphnia magna (Water flea), 21 d, 0.77 mg/l

Persistence and degradability

Ethoxylated branched C11-14, C13-rich alcohols

Biodegradability: Material is readily biodegradable. Passes OECD test(s) for ready
biodegradability.
Based on data from similar materials
Biodegradation: 95 %
Exposure time: 28 d
Method: OECD Test Guideline 301F

Bioaccumulative potential

Ethoxylated branched C11-14, C13-rich alcohols

Bioaccumulation: Bioconcentration potential is moderate (BCF between 100 and 3000 or
Log Pow between 3 and 5).
Partition coefficient: n-octanol/water(log Pow): 6.3 Estimated.
Bioconcentration factor (BCF): 283 Fish Estimated.

Mobility in soil

Ethoxylated branched C11-14, C13-rich alcohols

Partition coefficient (Koc): 5649 Estimated.

General Business
Page 10 of 13
Product name: ACULYN™ Siltouch Rheology Modifier Issue Date: 06/28/2022

13. DISPOSAL CONSIDERATIONS

Disposal methods: DO NOT DUMP INTO ANY SEWERS, ON THE GROUND, OR INTO ANY BODY
OF WATER. All disposal practices must be in compliance with all Federal, State/Provincial and local
laws and regulations. Regulations may vary in different locations. Waste characterizations and
compliance with applicable laws are the responsibility solely of the waste generator. AS YOUR
SUPPLIER, WE HAVE NO CONTROL OVER THE MANAGEMENT PRACTICES OR
MANUFACTURING PROCESSES OF PARTIES HANDLING OR USING THIS MATERIAL. THE
INFORMATION PRESENTED HERE PERTAINS ONLY TO THE PRODUCT AS SHIPPED IN ITS
INTENDED CONDITION AS DESCRIBED IN MSDS SECTION: Composition Information. FOR
UNUSED & UNCONTAMINATED PRODUCT, the preferred options include sending to a licensed,
permitted: Incinerator or other thermal destruction device. For additional information, refer to:
Handling & Storage Information, MSDS Section 7 Stability & Reactivity Information, MSDS Section10
Regulatory Information, MSDS Section 15

Treatment and disposal methods of used packaging: Empty containers should be recycled or
otherwise disposed of by an approved waste management facility. Waste characterizations and
compliance with applicable laws are the responsibility solely of the waste generator. Do not re-use
containers for any purpose.

14. TRANSPORT INFORMATION

DOT
Not regulated for transport

Classification for SEA transport (IMO-IMDG):

Not regulated for transport
Transport in bulk Consult IMO regulations before transporting ocean bulk
according to Annex I or II
of MARPOL 73/78 and the
IBC or IGC Code

Classification for AIR transport (IATA/ICAO):

Not regulated for transport

This information is not intended to convey all specific regulatory or operational

requirements/information relating to this product. Transportation classifications may vary by container
volume and may be influenced by regional or country variations in regulations. Additional
transportation system information can be obtained through an authorized sales or customer service
representative. It is the responsibility of the transporting organization to follow all applicable laws,
regulations and rules relating to the transportation of the material.

General Business
Page 11 of 13
Product name: ACULYN™ Siltouch Rheology Modifier Issue Date: 06/28/2022

15. REGULATORY INFORMATION

Superfund Amendments and Reauthorization Act of 1986 Title III (Emergency Planning and
Community Right-to-Know Act of 1986) Sections 311 and 312
No SARA Hazards

Superfund Amendments and Reauthorization Act of 1986 Title III (Emergency Planning and
Community Right-to-Know Act of 1986) Section 313
This material does not contain any chemical components with known CAS numbers that exceed the
threshold (De Minimis) reporting levels established by SARA Title III, Section 313.

Pennsylvania Right To Know

The following chemicals are listed because of the additional requirements of Pennsylvania law:

Components CASRN
Water 7732-18-5
2-Propenoic acid, sodium salt, polymer with sodium 2-methyl- 37350-42-8
2-[(1-oxo-2-propen-1-yl)amino]-1-propanesulfonate
Siloxanes and silicones, dimethyl 63148-62-9
Ethoxylated branched C11-14, C13-rich alcohols 78330-21-9

California Prop. 65
This product does not contain any chemicals known to State of California to cause cancer, birth
defects, or any other reproductive harm.

United States TSCA Inventory (TSCA)

The product is used in a food, drug or cosmetic application and is subject to the applicable regulation.
The product may only be used in the exempt application.

16. OTHER INFORMATION

Hazard Rating System

NFPA
Health Flammability Instability
3 1 0
HMIS
Physical
Health Flammability
Hazard
0/ 1 0

Revision
Identification Number: 4134948 / A001 / Issue Date: 06/28/2022 / Version: 3.1
Most recent revision(s) are noted by the bold, double bars in left-hand margin throughout this
document.

Full text of other abbreviations

AIIC - Australian Inventory of Industrial Chemicals; ASTM - American Society for the Testing of
Materials; bw - Body weight; CERCLA - Comprehensive Environmental Response, Compensation,
and Liability Act; CMR - Carcinogen, Mutagen or Reproductive Toxicant; DIN - Standard of the

General Business
Page 12 of 13
Product name: ACULYN™ Siltouch Rheology Modifier Issue Date: 06/28/2022

German Institute for Standardisation; DOT - Department of Transportation; DSL - Domestic

Substances List (Canada); ECx - Concentration associated with x% response; EHS - Extremely
Hazardous Substance; ELx - Loading rate associated with x% response; EmS - Emergency Schedule;
ENCS - Existing and New Chemical Substances (Japan); ErCx - Concentration associated with x%
growth rate response; ERG - Emergency Response Guide; GHS - Globally Harmonized System; GLP
- Good Laboratory Practice; HMIS - Hazardous Materials Identification System; IARC - International
Agency for Research on Cancer; IATA - International Air Transport Association; IBC - International
Code for the Construction and Equipment of Ships carrying Dangerous Chemicals in Bulk; IC50 - Half
maximal inhibitory concentration; ICAO - International Civil Aviation Organization; IECSC - Inventory of
Existing Chemical Substances in China; IMDG - International Maritime Dangerous Goods; IMO -
International Maritime Organization; ISHL - Industrial Safety and Health Law (Japan); ISO -
International Organisation for Standardization; KECI - Korea Existing Chemicals Inventory; LC50 -
Lethal Concentration to 50 % of a test population; LD50 - Lethal Dose to 50% of a test population
(Median Lethal Dose); MARPOL - International Convention for the Prevention of Pollution from Ships;
MSHA - Mine Safety and Health Administration; n.o.s. - Not Otherwise Specified; NFPA - National Fire
Protection Association; NO(A)EC - No Observed (Adverse) Effect Concentration; NO(A)EL - No
Observed (Adverse) Effect Level; NOELR - No Observable Effect Loading Rate; NTP - National
Toxicology Program; NZIoC - New Zealand Inventory of Chemicals; OECD - Organization for
Economic Co-operation and Development; OPPTS - Office of Chemical Safety and Pollution
Prevention; PBT - Persistent, Bioaccumulative and Toxic substance; PICCS - Philippines Inventory of
Chemicals and Chemical Substances; (Q)SAR - (Quantitative) Structure Activity Relationship; RCRA -
Resource Conservation and Recovery Act; REACH - Regulation (EC) No 1907/2006 of the European
Parliament and of the Council concerning the Registration, Evaluation, Authorisation and Restriction of
Chemicals; RQ - Reportable Quantity; SADT - Self-Accelerating Decomposition Temperature; SARA -
Superfund Amendments and Reauthorization Act; SDS - Safety Data Sheet; TCSI - Taiwan Chemical
Substance Inventory; TECI - Thailand Existing Chemicals Inventory; TSCA - Toxic Substances Control
Act (United States); UN - United Nations; UNRTDG - United Nations Recommendations on the
Transport of Dangerous Goods; vPvB - Very Persistent and Very Bioaccumulative

Information Source and References

This SDS is prepared by Product Regulatory Services and Hazard Communications Groups from
information supplied by internal references within our company.

THE DOW CHEMICAL COMPANY urges each customer or recipient of this (M)SDS to study it
carefully and consult appropriate expertise, as necessary or appropriate, to become aware of and
understand the data contained in this (M)SDS and any hazards associated with the product. The
information herein is provided in good faith and believed to be accurate as of the effective date shown
above. However, no warranty, express or implied, is given. Regulatory requirements are subject to
change and may differ between various locations. It is the buyer's/user's responsibility to ensure that
his activities comply with all federal, state, provincial or local laws. The information presented here
pertains only to the product as shipped. Since conditions for use of the product are not under the
control of the manufacturer, it is the buyer's/user's duty to determine the conditions necessary for the
safe use of this product. Due to the proliferation of sources for information such as manufacturer-
specific (M)SDSs, we are not and cannot be responsible for (M)SDSs obtained from any source other
than ourselves. If you have obtained an (M)SDS from another source or if you are not sure that the
(M)SDS you have is current, please contact us for the most current version.
US

General Business
Page 13 of 13