ERTAA213 Trane Chiller
ERTAA213 Trane Chiller
ERTAA213 Trane Chiller
Catalog Supplement
RLC-PR003-E4
General Data 200 series
2
© American Standard Inc. 1997
General Data 300 series
Note:
Data containing information on two circuits shown as follows: Ckt1/Ckt2
3
General Data 400 Series
Note:
Data containing information on two circuits shown as follows: Ckt1/Ckt2
4
Performance Data
Waterflow (l/s)
12.6 32.5 63.0
100
-250
225
ES
150
ES 00
170
2 120
ES
120
340
90
ES
ES
60
10 30
9 27
8 24
7 21
6 18
5 15
4 12
3 9
140
300
ES
2 6
ES
1
200 500
100.00 1000.00 10 000.00
5
Performance Data 50 Hz
1. Ratings based on sea level altitude and evaporator fouling factor of 0.00025 per ARI 550-90
2. Interpolation is permissible
3. Extrapolation is not permissible
4. kW input is for compressors only
5. Ratings are based on an evaporator drop of 10 °F
6. EER = Energy Efficiency Ratio (Btu/watt-hour). Power inputs include compressors, condenser fans and control power
6
Performance Data 50 Hz
1. Ratings based on sea level altitude and evaporator fouling factor of 0.00025 per ARI 550-90
2. Interpolation is permissible
3. Extrapolation is not permissible
4. kW input is for compressors only
5. Ratings are based on an evaporator drop of 10 °F
6. EER = Energy Efficiency Ratio (Btu/watt-hour). Power inputs include compressors, condenser fans and control power
7
Performance Data 50 Hz
1. Ratings based on sea level altitude and evaporator fouling factor of 0.0440 per ARI 550-90
2. Interpolation is permissible
3. Extrapolation is not permissible
4. kW input is for compressors only
5. Ratings are based on an evaporator drop of 5.6 °C
6. COP = Coefficient of performance (kW cooling/kW input). Power inputs include compressors, condenser fans and control power.
8
Performance Data 50 Hz
1. Ratings based on sea level altitude and evaporator fouling factor of 0.0440 per ARI 550-90
2. Interpolation is permissible
3. Extrapolation is not permissible
4. kW input is for compressors only
5. Ratings are based on an evaporator drop of 5.6 °C
6. COP = Coefficient of performance (kW cooling/kW input). Power inputs include compressors, condenser fans and control power.
9
Performance Data 60 Hz
1. Ratings based on sea level altitude and evaporator fouling factor of 0.00025 per ARI 550-90
2. Interpolation is permissible
3. Extrapolation is not permissible
4. kW input is for compressors only
5. Ratings are based on an evaporator drop of 10 °F
6. EER = Energy Efficiency Ratio (Btu/watt-hour). Power inputs include compressors, condenser fans and control power.
10
Performance Data 60 Hz
1. Ratings based on sea level altitude and evaporator fouling factor of 0.00025 per ARI 550-90
2. Interpolation is permissible
3. Extrapolation is not permissible
4. kW input is for compressors only
5. Ratings are based on an evaporator drop of 10 °F
6. EER = Energy Efficiency Ratio (Btu/watt-hour). Power inputs include compressors, condenser fans and control power.
11
Performance Data 60 Hz
1. Ratings based on sea level altitude and evaporator fouling factor of 0.0440 per ARI 550-90
2. Interpolation is permissible
3. Extrapolation is not permissible
4. kW input is for compressors only
5. Ratings are based on an evaporator drop of 5.6 °C
6. COP = Coefficient of performance (kW cooling/kW input). Power inputs include compressors, condenser fans and control power.
12
Performance Data 60 Hz
1. Ratings based on sea level altitude and evaporator fouling factor of 0.0440 per ARI 550-90
2. Interpolation is permissible
3. Extrapolation is not permissible
4. kW input is for compressors only
5. Ratings are based on an evaporator drop of 5.6 °C
6. COP = Coefficient of performance (kW cooling/kW input). Power inputs include compressors, condenser fans and control power.
13
Performance Data
50 Hz
Unit Size % Load Capacity Power EER IPLV
Tons kW
100 82 82 10.1 8.7
RTAA213 75 62 66 9.1
50 41 53 8.0
25 21 25 7.5
100 92 89 10.6 9.2
RTAA214 75 69 71 9.6
50 46 57 8.4
25 23 26 8.1
100 95 95 10.3 9.0
RTAA215 75 71 76 9.3
50 48 61 8.2
25 24 28 7.9
100 108 105 10.6 9.3
RTAA216 75 81 84 9.6
50 54 68 8.5
25 27 30 8.4
100 116 114 10.5 9.1
RTAA217 75 87 91 9.5
50 58 74 8.3
25 29 33 8.1
100 126 136 9.5 8.2
RTAA322 75 95 109 8.6
50 63 88 7.3
25 32 39 7.8
100 142 155 9.4 8.1
RTAA324 75 107 124 8.5
50 71 100 7.3
25 36 45 7.4
100 160 173 9.5 8.2
RTAA328 75 120 139 8.5
50 80 112 7.3
25 40 50 7.7
100 177 194 9.5 8.2
RTAA430 75 133 156 8.6
50 89 125 7.5
25 44 56 7.3
100 191 210 9.4 8.2
RTAA432 75 143 168 8.5
50 96 136 7.4
25 48 61 7.2
100 211 229 9.5 8.3
RTAA434 75 158 184 8.6
50 106 148 7.5
25 53 66 7.3
ARI part load data.
Power kW is for compressors only.
14
Performance Data
60 Hz
Unit Size % Load Capacity Power EER IPLV
Tons kW
100 100 101 9.6 10.7
RTAA213 75 75 65 10.1
50 50 37 12.2
25 25 16 10.3
100 113 112 10.0 10.7
RTAA214 75 85 75 10.3
50 57 43 12.2
25 28 24 9.4
100 116 116 9.9 10.4
RTAA215 75 87 78 10.3
50 58 52 10.8
25 29 21 10.5
100 124 127 9.7 10.6
RTAA216 75 93 82 10.3
50 62 52 11.5
25 31 22 10.6
100 135 137 9.7 11.1
RTAA217 75 101 83 10.8
50 68 49 12.5
25 34 24 10.2
100 147 161 8.9 9.9
RTAA322 75 110 105 9.3
50 74 60 10.4
25 37 23 12.1
100 165 183 8.8 9.6
RTAA324 75 124 120 9.2
50 83 74 10.1
25 41 27 10.7
100 185 204 8.8 10.1
RTAA328 75 139 124 9.7
50 93 77 10.3
25 46 26 12.3
100 206 230 8.9 9.1
RTAA430 75 155 151 9.3
50 103 109 9.2
25 52 47 8.5
100 221 248 8.8 9.6
RTAA432 75 166 154 9.6
50 111 100 10.4
25 55 48 8.7
100 245 270 8.9 9.8
RTAA434 75 184 164 9.9
50 123 105 10.8
25 61 62 7.9
ARI part load data.
Power kW is for compressors only.
15
Electrical Data 50 Hz
16
Electrical Data 60 Hz
17
Microprocessor control module :
“Adaptive Control™” protection and communication capabilities
Communication
The Unit Control Module (UCM-CLD) of the Application flexibility Integration into a Trane
RTAA offers several communication levels which The UCM-CLD is available with the output in six
considerably simplify the implementation of a
Building Management System
languages and in either English or metric (SI)
telemonitoring of the chiller or its integration in a units.
through the Serial link
Building Management System (BMS). The unit can be equipped upon request with a
Telemonitoring through a serial link communication card.
Operator interface All the data and functions available at the UCM
With easy front panel programmability of daily,
parallel link front panel can be transmitted or accessed
service start-up and machine configuration Analog input and output ports allow chiller through the serial link. The integration in a
settings and setpoints, the building manager and operation optimization or easy chiller monitoring Building Management or the chiller operation
service technician can customize the use of the when the machine is not integrated in a BMS. optimization in order to reduce the overal energy
UCM-CLD microcontroller to the unique consumption are thus considerably simplified.
conditions of the chiller plant whether the Remote running and alarm
purpose of the chilled water is comfort cooling or contacts Data which can be read
process cooling. Following parameters can be read by the Trane
The unit provides three single pole/double-throw
All the data that is necessary for the improved BMS through the serial link :
contact closures to indicate whether :
operation and easy serviceability of the chiller is • Entering and leaving evaporator water
• a failure has occured.
called up by simple keypad instructions and temperature
• the compressor is running.
presented on a highly readable screen. • Entering and leaving condenser water
• the compressor is running at maximum
capacity. This information may be used to temperature
Convenience authorize the start of an additional chiller. • Motor current
Enunciation of all information is at the front • Operating status : compressor stopped or
panel display (including power, voltage, amps, running, compressor running at full load or
External chilled water setpoint auto-limitation.
temperatures, pressures, number of starts and
operating hours). Messages are displayed using and current limit setpoint More than 100 data can be accessed or
clear language. The UCM allows the external setting transmitted.
independant of the front panel setpoint by one of
Readability the following three means : Orders which can be sent to the
• a remote resistor (fixed or adjustable) chiller
LCD, super twist, double line 40 character
• 2-10 VDC input
display is easy to read. The BMS can send following orders :
• a 4-20 mA input.
It is backlit so that the diplay can be read in a • Compressor start and stop
In the same way, the motor current can be
variety of equipment room lighting conditions. • Motor current limit
limited to optimize the total energy efficiency of
the installation. • Chilled water setpoint reset.
18
Tracer Summit
Chiller Plant Control
Tracer Summit's Chiller Plant Control The Chiller Plant Control program can
(CPC) application provides automation control comfort and industrial applica-
and energy optimisation of chiller plant tions as well as
through factory tested sequencing soft- special control sequences, including
ware. thermal storage and dual fuel chiller sys- PC Workstation Building
Control
tems. unit
As a manufacturer of chillers for over
60 years, Trane has gained tremendous The main features of Chiller Plant
experience in chiller plant applications. Control are:
The Tracer Summit Chiller Plant
Control application is designed to take • Chiller Sequencing
advantage of this expertise. This factory • Rotation Changes
tested software is powerful enough to • Base, Peak and Swing Operation Chiller N°1
handle such sophisticated applications
• Soft Loading
as decoupled, dual fuel, series, or even
• Individual Chiller Setpoint Calcula-
swing chiller systems yet is designed to
allow even the novice operators to tions
understand its set-up and operation. • Failure Detection and Recovery
• Manual Override
Chiller Plant Control monitors and • Chiller Performance Reports Chiller N°2
controls multiple chillers and their rela- • Remote Communications
ted pumps and valves to balance system • Pump and Ancillary Equipment
efficiency and equipment runtime to Control
optimise system performance.
• Interoperatorability with other compa-
tible Building Management Systems
In addition to control and monitoring,
the Chiller Plant Control program pro- • Control of up to 25 chillers in multiple
Chiller N°3
vides important status information that plants.
tells the user what is happening in the
chiller plant and what will happen next,
based on current operating conditions.
This status information is important for
troubleshooting purposes. Universal PCM
Chilled
water Other ancillary
pumps equipment
19
Mechanical Specification
TRANE Series RTAA packaged air cooled liquid Two refrigerant circuits steel, protected with a primary coating and
chiller consisting of accessible hermetic, direct- Each circuit including removable core filter finished with an acrylic paint. The paint can
drive screw compressors, with two independant dryer, liquid line shut-off valve, high pressure withstand 650 hours of salt spray test
circuits evaporator, condenser, microprocessor- relief valve. Electronic expansion valve
based controls and a unit-mounted motor minimizing superheat in the evaporator and Accessories and options
starter, refrigerant charged, factory runtested allowing chiller to run at reduced condensing • Compressor sound attenuating enclosure
and ready for operation. Unit are rated in temperature. • Condenser copper fins
accordance with ARI 550-90. • Communication card
Control panel • Vibration isolators
Compressor motor assembly Microprocessor-based unit control module • Disconnect switch
TRANE screw compressors, accessible- UCM utilizing the «Adaptive Control™» • Reversed water connections
hermetic, direct-drive, 2950 rpm (50 Hz). concept. The UCM provides all control and • Remote clear language display.
Separately housed, pressure-lubricated rolling safety functions including start-up and shut • Pressure gauges
element bearing groups at each end of both down, leaving chilled water control, • Flow switch
rotors. Fully modulating capacity control by compressor and electronic expansion valve • Communication card + load based chilled
use of a slide valve in the rotor section of the modulation, fans sequencing, anti-recycle water reset
compressors positioned by hydraulic action. logic, automatic lead/lag compressor starting • Communication card
Squirrel-cage two-pole induction motor, and load limiting. Unit protective functions • Plexiglass door (starter and control panel)
suction gas cooled. include loss of chilled water flow, evaporator • Under , over voltage protection
Oil separator and filtration devices provided freezing, loss of refrigerant, low and high • Condenser protection grids
separate from the compressor. refrigerant pressure, reverse rotation, • Compressor, evaporator grids
compressor starting and running overcurrent, • Discharge service valve
Evaporator phase loss, phase unbalance, phase reversal
Shell-and-tube heat exchanger with internally Factory testing
and loss of oil flow.
finned copper tubes, roller expanded into the Clear language display (2 lines, All RTAA chilers are fully run tested under
tubes sheets. Refrigerant inside the tubes and 40 characters), door mounted, indicates over load before shipment. Unit operation and all
water circulating in the shell. Maximum 20 operating data points including chilled control functions are factory checked and set.
operating pressure refrigerant side 16 Bar water setpoint, current limit setpoint,, leaving Shipment
(232 psig), water side 14 Bar (203) psig. chilled water temperature, evaporator and
19 mm thermal insulation of flexible closed Units ship fully assembled and single point
condenser refrigerant pressures and wired ready for operation after field
cell foam. Water flanged connections on temperatures.
200 serie and victaulic grooved on 300 and connection of power supply, electric
Over 60 messages are displayed when a interlocks and chilled water piping. Units ship
400 series. Heater cable for freeze protection. problem is detected. on a wooden skid with refrigerant and oil
Condenser Starter panel operating charges.
W-configuration High efficiency air cooled Unit mounted starter panel, protection class Quality assurance
condenser. Coils are seamless copper tubes, IP 55.
expanded into aluminium fins. Integral oil The Quality Management System applied by
Panel contains part winding type motor TRANE has been subject to independant third
cooler and subcooler circuits. Direct drive starter, single source power supply, 3-phase
discharge fans with totally enclosed air over party assesment and approval to ISO 9001:
current transformer for motor overload 1994, EN ISO 9001 : 1994, BS EN ISO 9001:
motors, having class “F” insulation and IP 55 protection.
protections. Fan guards. Leak tested at 21 Bar 1994. The products described in this
(304 psig), pressure rated at 35 Bar Unit structure catalogue are designed, manufactured and
(500 psig). Welded steel base frame, structural steel tested in accordance with the approved
profiles and panels, made of galvanized sheet system requirements as defined in the
TRANE Quality Manual.
RLC-PRC003-E4 - 0800
Supersedes C20 CS 604 E-1197
Trane reserves the right to alter any information without prior notice.
Société Trane - Société Anonyme au capital de 41 500 000 F - Siège Social : 1, rue des Amériques - 88190 Golbey - France -
Siret 306 050 188-0
00011 - RCS Epinal B 306 050 188