Labs were OSPF ipv6 configurations

Acces list : change to 104

SIM / Lab
ACL 1
IPv6 OSPF Simulator
GRE Multilink
RIPv2 Troubleshooting
OSPF Neighbor
D&D
PADI, PADO Drag and drop the PPPoE packet type
BPDU (BPDU Filter, BPDU guard, PortFast, Root guard, UplinkFast
————-
Which two statements about exterior routing protocols are true? (Choose two)
A. They determine the optimal path between autonomous systems
B. They determine the optimal path within an autonomous systems
C. Most modern networking supports both EGP and BGP for external routing
D. Most modern network routes support both EGP and EIGRP for external routing
E. BGP is the current standard exterior routing protocol
————-
Which command is used to enable LLDP globally on a Cisco IOS ISR?
A. lldp run
B. lldp enable
C. lldp transmit
D. cdp run
E. cdp enable
A
———-
10.0.0.0/8 How many Host bits
24 Bits
———-
Which Step start Load IOS
A. Rommon
B. POST
C. Bootstrap
D. ?
———–
In APIC-EM what is the icon if there is an ACL on the device blocking the traffic on the path?
——
Which two statements about northbound and southbound APIs are true? (Choose two)
A. Only southbound APIs allow program control of the network.
B. Only northbound APIs allow program control of the network.
C. Only southbound API interfaces use a Service Abstraction Layer.
D. Only northbound API interfaces use a Service Abstraction Layer.
E. Both northbound and southbound API interfaces use a Service Abstraction Layer.
F. Both northbound and southbound APIs allow program control of the network.
——
Which utility can you use to identify redundant or shadow rules?
A. The ACL trace tool in Cisco APIC-EM.
B. The ACL analysis tool in Cisco APIC-EM.
C. The Cisco APIC-EM automation scheduler.
D. The Cisco IWAN application.
——–
Which two pieces of information can you determine from the output of the show ntp status
command? (Choose two)
A. whether the NTP peer is statically configured
B. the IP address of the peer to which the clock is synchronized
C. the configured NTP servers
D. whether the clock is synchronized
E. the NTP version number of the peer
———
Which two actions must you take to correctly configure PPPoE on a client? (Choose two)
A. Define a dialer interface
B. Create a dialer pool and bind it to the virtual template
C. Define a virtual template interface
D. Create a dialer pool and bind it to the physical interface.
E. Create a BBA group and link it to the dialer interface
———-
After an FTP session to http://ftp.cisco.com fails, you attempt to ping the server. A ping
to http://ftp.cisco.com
also fails, but a ping to the IP address of the server is successful. What is reason for the failed FTP
session?
A. The assigned DNS server is down
B. An ACL is blocking the FTP request
C. A firewall is blocking traffic from the FTP site
D. The internet connection is down
———-
Which two circumstances can prevent two routers from establishing an OSPF neighbor adjacency?
(Choose two)
A. mismatched autonomous system numbers
B. an ACL blocking traffic from multicast address 224.0.0.10
C. mismatched process IDs
D. mismatched hello timers and dead timers
E. use of the same router ID on both devices
———–
Which two facts must you take into account when you deploy PPPoE? (Choose two)
A. DDR idle timers must be configured to support VPDN login.
B. PPPoE supports a maximum of 10 clients per customer premises equipment
C. DDR is not supported
D. You must manually configure IP addresses on the PPPoE interface
E. An individual PVC can support one PPPoE client
———–
Which circumstance is a common cause of late collisions?
A. native VLAN mismatch
B. overloaded hardware queues
C. duplex mismatch
D. software misconfiguration
————
Which two statements correctly describe the ping utility? (Choose two)
A. It uses ICMP
B. It can identify source of an ICMP ―time exceeded‖message
C. It can identify the path that a packet takes to a remote device
D. It can verify connectivity to a remote device without identifying the path
E. It use UDP
————-
Which two server types are used to support DNS lookup? (Choose two)
A. web server
B. name resolver
C. authoritative name sever
D. ESX host
E. file transfer server
————
Which two approaches are common when troubleshooting network issues? (Choose two)
A. round-robin
B. divide and conquer
C. policingD. top down
E. layer-by-layer
———–
Which three features are represented by the letter A in AAA? (Choose three)
A. authorization
B. accountability
C. authentication
D. authority
E. accessibility
F. accounting
———–
Which two EtherChannel PAgP modes can you configure? (Choose two)
A. Auto
B. Desirable
C. Active
D. Passive
E. On
———-
Which command should you enter to configure a DHCP client?
A. ip dhcp pool
B. ip dhcp client
C. ip helper-address
D. ip address dhcp
———-
What is the simplest IP SLA operation that can measure end-to-end response time between device?
A. CMP path jitter
B. ICMP path echo
C. ICMP jitter
D. ICMP echo
———
Which Rapid PVST+ port role provides a different path to the root bridge?
A. designated
B. forwarding
C. backup
D. alternate
——-
Drag and drop the routing table components on the left onto the corresponding
letter from the exhibit on the right. Not all options are used.
——–
What is the maximum number of switches that StackWise can support in one stack?
A. 6
B. 8
C. 9
D. 10
C
———–
Which two tasks should you perform to begin troubleshooting a network problem? (Choose two)
A. Gather all the facts
B. Monitor and verify the resolution
C. Define the problem as a set of symptoms and causes
D. Analyze the results
E. Implement an action plan
————
Which command should you enter to configure a device as an NTP server?
A. ntp authenticate
B. ntp master
C. ntp peer
D. ntp server
————-
Which two statements about TACACS+ are true? (Choose two)
A. It combines authentication and authorization to simplify configuration.
B. It uses TCP port 49.
C. It supports full command logging.
D. It encrypts the password only.
E. It uses UDP port 49.
———-
Which keyboard shortcut can you use to exit the System Configuration Dialog on a Cisco
networking device and return to privileged EXEC mode without making changes?
A. Ctrl-C
B. Ctrl-V
C. Shift-Esc
D. Ctrl-Alt-Delete
———-
Which frame type allows STP to compute the spanning-tree topology?
A. LSA
B. RSTP
C. LSP
D. BPDU
———-
Which configuration register value can you set on a Cisco device so that it ignores the NVRAM
when it boots?
A. 0x2124
B. 0x2120
C. 0x2142
D. 0x2102

When a switch is running in VTP server mode, VLAN configuration information is stored in which file?
A.config.text
B.vlan.dat
C.startup-config
D.Vlan.config
Which two statements about southbound APIs are true?

 They enable communication between the controller and the network device
 They communicate with the management plane
 They use HT TP messages to communicate
 OpenFlow is a southbound API standard
 They enable communication between the controller and SDN applications

QUESTION 1:

which two statements about single- and dual-homed links are true?(choose two)

A.single homed connections to a service provider can use either static routing or BGP

B.Single homed connections to a service provider require OSPF or EIGRP

C.Dual homed connections to multiple service prviders can use OSPF or EIGRP for load balancing

D.Dual homed connections to service prviders must frequently use static routing

E.Dual homed connections to multiple service prviders typically use BGP

QUESTION 2:

when you configure and boot a new device, when does the running configuration becom active?

A.when ios is loaded into RAM

B.when the startup configuration is cpied into RAM

C.immediately after the power-on-self-test

D.when the devices boots to RAM

QUESTION3:

what is the effect of portfast on the mac aging process?

A. it prevents fast aging of mac adresses when RSTP is in use.

B. it prevents fast aging of mac adresses when IEEE 802.1D is in use

C. it ignore the mac aging timer when RSTP IS IN use

D. it ignore the mac aging timer when IEEE 802.1D is in use

You are configuring a 100 mb fastethernet connection between a pc and a switch .which action must you
take to configure the speed on each of the interfaces?

A. set the switch port to 100 mb and the pc interface to auto negotiate

B. set both interfaces to auto negotiate

C. set both interfaces to 100 mb

D. set the switch port to auto negotiate and the pc interface to 100mb

What are two requirements for an HSRP group? (Choose two)

A. exactly one active router

Which command should you enter to configure a single port to discard inferior BPDUs?

 spanning-tree portfast bpdufilter default

Count of violations – restrict

Sh ip int – ip address and subnet | name or number ACL | DHCP relay | status and protocol status

– (sidebar question) Vlan – How will switch SW2 handle traffic from VLAN 10 on SW1? I said it’d go to
Vlan 100 since that was the vlan on sw2. It sends the traffic to VLAN 100
– (sidebar question) What must the HSRP consist of, pick two? an active, or a standby, or an active
standby, a virtual backup were the choices. Active and 2 or more standby router
– Err disabled state when port gets an inferior bpdu? bpdu guard
– Upgrading the boot image, know what three examples would look like, you have to pick three. It asks
mentions tftp, rom, and flash. 6 choices total and some start with boot system flash, but anyways, know
what that command looks like.
Router(config)# boot system flash c4500-p-mz.121-20.bin
Router(config)# boot system tftp c7300-js-mz.122-33.SB8a.bin
Router(config)#boot system rom c7301-advipservicesk9-mz.124-24.T4.bin
– know the command to see which interfaces are affected by an access list.
-Know your sys log levels. IT said pick 3, but it had 4 different levels in there so I don’t remember what
they were looking for there. 0-4 | emergency | critical | error
(sidebar)- IPV6 frame vs IPV4 frame
– What routing protocols/methods do ISP’s use for routing? It had like EIGRP and BGP and OSPF in the
options, and it wasn’t just a one word answer choice but like ―EIGRP and BGP can be used.
– Dual homed vs single homed mqc. (pick two) - Single-mode cable is most appropriate for
installations longer 10 km, Multimode cable supports speeds between 100 Mbps and 100 Gbps
– (Question in sidebar) cam table question like what’s included in it or something,- source address
– (Question in sidebar)what’s neeeded for static route? next hop/destination network
– (Question in sidebar) Which two statements about IGP and EGP routing protocols are true? Service
providers use OSPF and IS-IS for intra-AS routing , IGP routing protocols are used within internal
networks.
– Know your private IP IP’s range, and how many subnets you can have in a given IP range
– VTP Question (dont remember the specifics but didnt see it on here)
– (sidebar question) dynamic vs static routing (choose two) how they differ, like which one shares a
database and which one has faster convergence
– RIPv2 command (specifically, know about the version command, like the syntax of it)
– (Question from sidebar) Common cause of runts? Collissin wire
The PaGP trunk mode things - Auto Desirable
– (Question from sidebar) One about PPP (Which PPP subprotocol negotiates authentication options? ) -
LCP
– (Question from sidebar) Where the answer was LCAP-M.. something, it’s in one of the sidebar
questions, it’ll stick out like a sore thumb when you’re going through them.
– (Question I didn’t see in sidebar about reading the interface info about an ADV router to determine
which statements were true.
– MQC about how to fix speed issue where there’s a switch and a pc and there’s a speed of like 100
mbps or something. set both interfaces to auto negotiate
(Question from sidebar) What does the internet layer encapsulate –ICMP and ARP
– Router on a stick mqc question about the first steps you need to do - configure the subinterface with
an IP address, configure encapsulation dot1q
– MQC about first step in configuring NAT. - Define inside and outside interfaces.
– A question asked about what the configuration file would look like? and the options were weird, like
config.tex, or startup config. I didnt know it.
-What are the two primary functions of APIC- EM? It automates network actions between different
device types. , It makes network functions programmable.
– Drag and Drop – Max TTL/Min TTl/Timestamp/Timeout
– Drag and Drop ppoe order, not just their definition - IN OUT R S T PADI, PADO, PADR, PADS, PADT
– Drag and Drop Administrative distance order MY pneumonic = [C]ats [S]ometimes [E]at [E]verything
[O]n [R]ugs. First letter is how you remember what the routing is, so c is connected, s is static, first e is
ebgp..etc…
– Be able to tell the diff between IPV6 link local, broadcast, and private address. Be able to classify it just
by looking at the first part of it. - FC00::/7 is used in private networks., FE80::/10 is used for link-local
unicast, FF00::/8 is used for IPv6 multicast.
– (question from sidebar) First two troubleshooting steps, - Gather all the facts, Define the problem as
a set of symptoms and causes
– (question from sidebar) configuring ntp - ntp master
– (question from sidebar) LLDP question where answer was LLDP-MED
– What state is a port in by default with Voice vlan - switchport access
– one question gave you a short log and you had to say if it was shut down, restrict protect, or shut down
vlan. was in errdisabled state but also said at the end that the state was changed to down - Shutdown
– (question from sidebar) about what router does when it takes gets the packet
– (question from sidebar) Refer to the exhibit. Which BGP configuration do you need to apply to router R4
to allow traffic to flow normally on this network? No EBGP
– (question from sidebar) Which destination addresses will be used by Host A to send data to Host C?
(Choose two) Mac address of routers interface and IP of Host C is what I picked
– (question from sidebar) Which chassis aggregation technology combines two physical switches into one
virtual switch? VSS
-(question from sidebar) one showing you a screenie of a routers command line with 20 routes, where 10
each were being load balanced. there are 20 different network masks within the 10.0.0.0/8 network,
Ten routes are equally load-balanced between Te0/1/0.100 and Te0/2/0.100