FIRST ORDER ON ALIEXPRESS

Chip Timer C005

C005 Cheap Delay Timer

Need to turn off your circuit for some time but don't want to fiddle with a microcontroller/sleep
settings? How about using a delay timer board for 10 cents?

Benjamen Lim

Aug 24, 2019 • 5 min read

I recently got very interested in controlling the amount of power my boards use because between
transmitting data and using battery powered devices, there isn't a whole lot of energy to spare if
you don't want to be tied to a wall wart.

Adafruit and Sparkfun both sell the TPL5110 breakout boards that essentially act as delay
switches that start a timer when a switch closes. The system shuts off the power by sending a
signal to the trigger pin, which opens the circuit. When the period is up, the switch will open
again. However, because it is a little expensive for me, I was looking around for alternatives, and
this little board caught my eye:
This is advertised as delay timing chip/delay chip/Trigger delay IC/2s-1000h timing IC. It is also
known as the C005 delay chip due to the markings on the side. It is literally a piece of PCB with
an epoxy glob. It also costs about 50 times less than an equivalent board from Adafruit or
Sparkfun. Unfortunately, all of the descriptions online appear to be a copy-paste of the original
instructions, which is a set of gibberish sentences in English:
Hard to understand!

Translation
Specifications
The size of the board is 12mm x 12mm, with an operating voltage of 2v to 5v. The timing that
the Output is low for can be set to a minimum of 2 seconds and a maximum of 1000 hours.

Function
1. While the trigger is not activated the output is high. The trigger can be activated by
sending a falling signal to the trigger pin.
2. Once the trigger is set by an external controller, the output goes low. An internal timer
starts as well.
3. Once the timer completes, the output will reset and the chip will wait for the next falling
signal.
 4. The chip is not repeatedly triggered, meaning that in the time between it is triggered and
resets, it will not respond or keep track of any other falling signals from the external
controller.
5. The trigger can be tied to the output as a short detector, so it will cut off the power when
there is a short circuit to ground. It will then attempt to reset the power after a short
period of time. (a pretty nifty feature!)

Features
1. Uses CMOS and is lead free (this is debatable)
2. It can be used to power a LED or may be used to control a transistor that can be used as a
switch for high-power circuits. Current limiting resistors are required.
3. The timing can be changed by adjusting the resistance, and there are prescalers available
to further change the timing.

Diagram

Testing
After some experimentation with the C005 IC, I figured out that when Trigger is pulled to LOW,
the falling edge causes the OUT pin to go LOW for a specific period of time before going back to its
default state of HIGH.  

This is a one shot timer because it requires an external input for it to change state.

For a low power circuit, the ground can be tied to the OUT pin. This way the delay works as a low
side switch and controls power to the circuit through the connection to ground. If an external
trigger is activated, the circuit will turn on and process the event for a predetermined length of
time before it turns off.

Another way this can be used is to tie the output to a transistor that acts as a high power switch.
Let's say I want a circuit to turn off for an hour each time. I will first pick out a resistor that gives
me an hour from the timing table, then I will then program my microcontroller to send a signal to
the trigger pin when it is done. This will cause the output to go low for the specified period of
time (an hour) before it automatically goes back to high again.

The OUT pin is not able to source a significant amount of current, so it is not possible to run a
circuit directly from the OUT pin unless your current requirements are very small. Holding the
Trigger down does not automatically trigger the output again, as the condition for toggling the
OUT pin is a falling edge on the Trigger pin.

The nice thing about this chip is that the solder pads are spaced 0.1 in apart, so they can be
soldered to standard headers. Another benefit of this IC is that it can also be used as a timer for a
much longer period than the TPL5110. While it definitely does take up more space, it is 10x
cheaper than a TPL5110 in single quantities, costing about $0.15. I measured the timing period
to be stable to a few milliseconds.

Connecting the circuit

C005 overlay, made in Inkscape

This chip takes in voltages from 2V to 5V. You will need to solder a resistor to set the timer.

P1 and P2 are primarily used to extend the time. By shorting P1, you extend the time by 8 times,
by shorting P2, you extend the time by 64 times. Shorting both yields a time extension of 512
times.

By placing either a SMD resistor or a through-hole resistor on the board, the time can be varied
as seen in the reference table at the bottom of the post. The timing is also dependent on the
voltage that is applied to the circuit. Alternatively, you can also add a trimpot to vary the delay.

For stability, a pull-up resistor can be added to the trigger pin. Do note that the output pin
appears to be capable of sinking up to 30mA and is not a full power switch. You will need to add
the power circuitry yourself if you intend to use this timer IC for high powered operations.

Steps
1. Select a resistor and solder it in
 2. Connect power and ground
3. Tie the trigger pin to an external device or switch
4. Tie the output pin to the circuit to be powered

Power consumption
This chip/board draws about 100uA when active (when it is keeping time, OUT is low). It draws
about 1uA when it is sleeping. It does not provide much benefit compared to sleep modes, which
for the nRF52840 or ESP32, draws about a few uA when they are sleeping. However, if we are
considering a more complex circuit like a board with other components that are also drawing
power, then maybe this chip has a role in being the middleman for power management. This can
also be useful in circuits that need to be timed but don't have a microcontroller, or retrofitting
existing circuits to have sleep features.

Reference Table
These times apply when both P1 and P2 are not shorted.

Resistance Timing under 3V (s) Timing under 4.5V (s)

10K 5.8 4.8
20K 8.9 8
30K 12.1 11.4
51K 19.2 18
75K 26.5 25
100K 34 32
150K 49 46
200K 65 60
240K 78 74
300K 96 92
390K 123 119
510K 155 150
560K 175 168
620K 199 187
750K 230 222
820K 255 246
1M 330 291
1.5M 383 432
2M 598 568
3M 762 762
4.7M 1425 1165
Resistance Timing under 3V (s) Timing under 4.5V (s)
5.1M 1631 1331
10M 2921 2621
15M 4394 3813
20M 5160 4660
22M 7052 6452
MODUL PEREKAM SUARA
CHIP RECODER YSJ-120S chipcorder module
Chinese electronics products are very cheap. So cheap that you may wonder if there is quality delivered
for such a low price. In this blog this is investigated. Chinese products are bought through the well-
known internet mail order companies and tested by an experienced electronics engineer in his own lab.
Although each article contains one sponsor ad, there is no commercial influence. The sellers do not
know that their products are tested and described on this blog.

(Published on 07/04/2021)
 With this module, you can record a message by pressing one button and then
play it back on a speaker connected to the module by pressing a second
button.

Introduction to the YSJ-120S chipcorder module

What is a chipcorder?

This term 'chipcorder' was the name invented by the chip manufacturer ISD (now part of Nuvoton) for a
chip in which, at the touch of a button, you can record a spoken message and, at the touch of a second
button, play back that message via a speaker connected to the chip. Well-known chips of this series,
such as the ISD1806, have a limited memory, which means that you can only record about five seconds
of audio. Moreover, the sampling rate is quite low, so there is a lot to complain about in terms of sound
quality.

What can you do with such a chipcorder?

A chipcorder is an ideal toy for the electronics hobbyist. You can think of numerous fun applications for
it, such as:

 Equipping a present with a spoken congratulation that is played when the birthday girl or boy
opens the package.
 Equipping a self-built steam locomotive, for example the UGEARS 70058 3D (recommended),
with the typical sound that such a locomotive produces.
 Equipping a home-made burglar alarm with the possibility of producing dog barking when a PIR
sensor triggers an alarm.

The YSJ-120S, a Chinese chipcorder

For barely € 1.53 (AliExpress), you can buy a small ready-made module measuring just 30 mm by 28 mm.
It contains a chip-on-board version of an IC from the ISD series under a black 'blob', the complete circuit
to record to and play from this IC and ... most importantly, a second chip that turns out to be a 1 MB
flash memory that allows you to record no less than 120 seconds of audio on the module in high quality.
 The little module YSJ-120S which allows you to record and
playback 120 seconds of audio. (© AliExpress)

A detailed description of the YSJ-120S

In the picture below, you see the front and back side of this module. Next to the 'blob' under which the
soundchip is hidden, you can see a FT25H08S. This is a flash memory with a capacity of 1,025 kB. Under
this chip is a 2TY transistor, which does have a base resistor (R15), but whose emitter is not connected
(R10). The collector also goes to three resistors R4, R7 and R12, which places are empty on the PCB.
On the input side, you can see that the 'hot' side of the microphone goes to a capacitor C6 as well as to a
resistor R3 of 4.7 kΩ. We assume that this resistor serves for the powering of an electret microphone
and that you can therefore connect such a capsule directly to the input.

On the bottom of the module you see four pads PE, PL, RE and RL. You connect four pushbuttons to
these pads to control the recording and playback capabilities of the module. At the top, you must
connect the power supply between GND and B+ and an 8 Ω to 32 Ω loudspeaker between the two SPK
pads. Please note that these SPK connections are not grounded, so the speaker will float relative to
ground! This is important if you want to connect the SPK outputs to the LINE input of an amplifier, for
instance! We will come back to this later.
Unfortunately, it is impossible to reconstruct the schematic completely because it is obviously unknown
how the COB chip is connected to the PCB under the 'blob'.
 The front and rear of the YSJ-120S. (© 2021 Jos Verstraten)

The specifications of the YSJ-120S

We have gathered the following specifications from the various descriptions of the module:
       - Supply voltage: 3.0 Vdc ~ 5.0 Vdc
       - Standby power consumption: less than 5 μA at 3.6 V power supply
       - Recording time: 120 s max.
       - Recording format: ADPCM
       - Sampling rate: 16 kHz
       - Sampling resolution: 14 bit
       - Output power: 0.6 W into 8 Ω
       - Speaker impedance: 8 Ω ~ 32 Ω

A comment on these specifications

You may notice the same thing we noticed when reading the specifications. Sampling with 14 bit at a
rate of 16 kHz? And then squeezing all the samples from 120 seconds of recording into a 1 MB memory?
That is not possible! With linear sampling, this would indeed not be possible. However, according to the
specifications, the module works with 'ADPCM'. That is the acronym for 'Adaptive Differential Pulse-
Code Modulation'. This system works very differently from the system that is used on audio CDs, for
example. Audio CDs are sampled at a fixed sampling frequency (44.1 kHz) and each sample is equally
wide (16 bits). With ADPCM, the number of bits and the sampling rate depend on the fluctuation of the
signal. If it varies very quickly, then it is sampled quickly and with a lot of bits. If the amplitude of the
signal does not vary greatly, then few bits and a low rate are used. Thanks to this principle, it would
indeed be possible to fit 120 seconds of audio into 1 MB. The 16 kHz and 14 bits of the specifications
should probably be regarded as maximum values.

The connection diagram of the YSJ-120S

In the figure below we have summarised the connections on the module. The function of the four push
buttons is as follows:
  RL:
The module records audio as long as you press this push button.
 RE:
The module starts recording after you press this button and records until you press this button
again. If the maximum recording time is over before you have pressed the second time, the
module automatically stops recording and goes to standby.
 PL:
The module is playing as long as you press this button.
 PE:
The module starts playback after you press this button and stops when you press this button
again. If the recorded audio clip ends earlier, the module stops playing automatically and goes
to standby.

The start of a recording is announced by a short beep from the loudspeaker, the end by two short
beeps. These beeps are of course not recorded.

The connection details of the YSJ-120S. (© 2021 Jos Verstraten)

The first experiments with the YSJ-120S

Sampling a sine wave
Because we are curious about the quality of such a cheap module, we first connected the YSJ-120S to
our sine generator and let the module sample a sine wave with a frequency of 1 kHz. We solder a 32 Ω
resistor as load between the SPK pads and connected our oscilloscope to it. To prevent a short circuit of
one of the speaker outputs to ground through our measuring equipment, we used our latest lab
acquisition, a DP1007 differential probe from Micsig. Both inputs of this probe have a resistance to
ground of 4 MΩ, so both speaker outputs of the module can be safely connected to it.
To our big surprise, no 1 kHz sine wave can be measured over the load, but a square pulse, see the
picture below.
 The signal between the SPK outputs of the module.
(© 2021 Jos Verstraten)

It is clear: the module works with pulse width modulation (PWM) and the conversion of this digital pulse
train into an audible signal is left to the inductive load and mechanical inertia of the loudspeaker. A
cursor measurement on the oscilloscope gives an impression of the frequency of the PWM signal, which
is around 2.7 MHz.

Measuring the frequency of the PWM signal at the output.

(© 2021 Jos Verstraten)

A consequence of this system is that no distortion measurements can be made, so we can only judge
with very subjective auditive perception of the result.

Digitising music
As a second test, we connected the LINE output of our PC to the audio input of the module and
recorded some music using 'WinAmp'. What strikes us is that the module has a very sensitive input. We
have to put a 10 kΩ / 47 kΩ resistor divider between the LINE output of the PC and the input of the
module and set the volume control of 'WinAmp' in the middle position to avoid overloading the module.
Of course you can connect the module to the LINE via a logarithmic potentiometer of 10 kΩ and
experiment with the right input level this way. To judge the quality of the reproduction we use
headphones. After some experimenting with the volume setting of 'WinAmp' the verdict on the
reproduced music was: 'Not bad, but not great either!'.

The maximum recording time

We have recorded some music samples from the album 'The Wall' by 'Pink Floyd' and found a maximum
recording time of 2 minutes and 16 seconds. So that's pretty much what the specifications promise.

Application example of the YSJ-120S

The YSJ-120S as an alarm generator in a burglar alarm
You can record music as described or store voice messages in the module via an electret microphone.
However, it is fun to load the module with special sound effects, such as the sound of a steam train. As
an example, we have assumed that the module will be part of a burglar alarm that produces dog barking
when one of the PIR sensors triggers an alarm. How the module can respond to this is obvious. Connect
a small reed relay to the alarm output of the PIR sensor and connect the reed contacts of this relay to
the PE and GND pads of the module. Now it's just a matter of reading the impressive and terrifying dog
barks into the flash memory.

Downloading a sample from 'Soundfishing'

The internet is full of sites from which you can download sound samples, whether you pay for them or
not. For example, you can take a look at 'Soundfishing' where we found a nice sample under the name
'dog bark 01'. You can download this sample for free, resulting in a 126 kB large file
'sf_dog_barking_07.mp3'. Despite its size, this MP3 file only delivers a little over six seconds of sound.
This is far too little, which is why we are going to edit this file.

Opening the file in 'Audacity'

We still have a very old version 1.2.6 of 'Audacity' on our PC, one of the best known and most famous
open source sound editing programs for Windows. The latest version is 3.0.0 and you can download it
from 'Audacity team'.
You can load the MP3 file into this program. You see the barking dog file as an oscillogram in the
program's window, see the figure below. 
 The sound sample in the window of 'Audacity'. (© 2021 Jos Verstraten)

Editing the file in 'Audacity'

You can now apply all the effects and tools available in 'Audacity' to the sample. The idea is that you get
a sample of about twenty seconds of which everyone thinks that a bloodthirsty dog is waiting behind the
front door. This is a little more difficult than it looks and it will take you quite a while.
Most important tip: avoid repetitions, as they immediately make the sound unbelievable. Also, make
sure that there is no noise between the dog sounds, because then you will fail immediately.
You start by adding an extra duration of twenty seconds to the sample via the 'Generate' menu and the
'Silence' option. These twenty seconds are now empty and you can fill this part with barking by copying
parts of the sample. To do this, select the segment with the mouse button pressed and use the 'Edit'
menu and the 'Copy' option to store this fragment in memory. Afterwards, place the cursor somewhere
in the silent area and copy the barking via 'Edit' and 'Paste'. You can also amplify a barking using the
'Effect' menu and the 'Amplify' or 'Bass Boost' options.
After some experimentation, the thirty seconds are filled with a sound sample that believably imitates a
very angry dog, see the figure below.
 The sound sample is extended to about thirty seconds. (© 2021 Jos Verstraten)

Loading the sample into the YSJ-120S

Finally, you can load your own sample into the module. You can do this in the same way as described
above by connecting the module to the LINE output of your PC via a potentiometer and playing the
sample in 'WinAmp' or a similar programme.

Amplifying the sound of the YSJ-120S

With the 0.6 W output power of the module, you will not be able to reproduce an angry big dog.
Therefore, you connect an amplifier to the output of the module. Such amplifiers PCBs can be purchased
for a few euros at the well-known Chinese mail-order companies. However, two problems arise here:
       - The PWM signal on the output. 
       - The floating outputs.
Both problems can be solved by inserting a small audio isolator between the SPK outputs of the module
and the input of an amplifier. A well-known type is 'EI14-600:600', see the picture below. It is completely
symmetrical, has two identical windings with a resistance of 140 Ω, an impedance of 600 Ω at 1 kHz and
an inductance of 290 mH.
 The use of an isolation transformer when coupling the module to an amplifier. (© 2021 Jos Verstraten)

The transformer costs only € 1.00 and ensures that the two SPK outputs of the module are not shorted
to ground. In addition, the impedances of both windings ensure that the fast-switching PWM signal on
the SPK outputs is converted into something more resembling a traditional audio signal.

(Banggood sponsor ad)

3 pcs YSJ-120S sound module

Product description:
 
[Transmitter module ] Product Model: TX118SA-4 (10 pack)
Transmitting power: 11dbm
Emission current: 10 mA
Rate of fire: maximum 10KB / S
Operating Voltage: DC 3V-24V
Encoding : EV1527 1527 Learning code
Each module has a unique address code, the address code of K1~K4 which are on the
same module is the same.
 
[Receiver module ] Product Model: RX480-E4 
Working Voltage : DC3.3~5V
Quiescent Current : ≤5mA
Output current : 10 mA
Working Frequency: 433MHz
Receive Sensitivity: -108dB
Working Temperature : -25~75
Working mode: Momentary Mode , self-locking (Toggle-Mode of the 4 Channels) ,
interlocking
The output: 4 channel CMOS level signal Corresponding to the remote control ABCD 4
buttons.
Pins Instruction
GND : ground or negative pole
+V : DC3.3~5V input
D0: Data output
D1: Data output
D2: Data output
D3: Data output
VT: Output
 
How to match the transmitter and receiver
 
1. Delete existing data: Press learning button(on the receiver) 8 times. Response: LED
flashes 7 times.
2. Learning remote code: press learning button(on the receiver) once, twice or three
times (see below).
LED turns on: learning mode is active. Press any button of the remote control.
LED indicator flashes three times: learning successfully completed.
3. Test: after the above operation , the receiver board can be controlled by the remote
control.
More transmitters with different IDs can be learned and stored additionally, starting with
step 2.
A mixture of different modes is possible.
 
Button usage (sets mode and starts pairing process):
Press once: Inching mode (Momentary Mode)
Press twice: self-Lock Mode (Toggle-Mode of the 4 Channels)
Press three times: interlocked mode (selected channel active and be
cleared, if another channel becomes active) 
GREMA 10PCS 433.92MHz super heterodyne receiver
module with decoding wireless decoding module remote
control 1527 learning code
Applications

1.wireless power switch, socket, remote control switch, receiver module,

2. access control, electric cars, motorcycles, automobile anti-theft products, remote door
openers, closers control system
3. security, surveillance systems, home security products, electric doors, alarm host, alarm
4. rooms controls, shutter doors, windows, remote control socket, remote control LED, remote
audio remote control electric doors, garage door remote control, remote control retractable
doors, remote rolling gates, sliding door
5. smart home products, remote control curtains, remote MP3, audio

Specifications

Model Number:RX480E-4C
Working Temperature : -25~75C
Receive Sensitivity: -108dB
Quiescent Current : <=5mA
Working Voltage : DC3.3~5V
Working Frequency: 433.92MHz
Support encoding chip model: EV1527, PT2262
(Others can be customized,but at least 1000pcs)

Function

Pin-out instructions:
GND : groud or negative pole
+V : DC3.3~5V input
D0: Data output
D1: Data output
D2: Data output
D3: Data output
VT: Output
Working mode:Point move, self-locking, interlocking
The output: 4 channel CMOS level signal Corresponding to the remote control ABCD 4 buttons.
 

Introduction of working mode:

1. Press the learning button on the module 1 time. After the remote controller learns, it enters
the jog mode;
2. Press the learning button on the module twice, and the remote controller will enter the self-
locking mode after learning;
3. Press the learning button on the module 3 times, and the remote controller will enter the
interlock mode after learning;
4. Press the learning button on the module 4 times. After the remote control learns,
Enter two-way self-locking + two-way jog mode;
5. Press the learning button on the module 5 times. After the remote control learns,
Enter two-way jog + two-way interlock mode;
6. Press the learning button on the module 6 times. After the remote control learns,
Enter two-way self-locking + two-way interlocking mode;
7. Press the learning button on the module 7 times. After the remote control learns,
Enter two-way interlock + two-way interlock mode;
Explanation of the purpose of this LED output signal:
When any button of the remote control is pressed, the receiving end decodes and decodes
correctly, the LED will output a high-level signal 1. When the remote control button is released,
the LED output will become 0.
That is: it will be output only when the reception is valid and decoded correctly.
Operating Introduction

Clearing the code :

Push the learning button on the receivers for 8 times , the codes will be cleaned .
After clearning the code, all the remote control cannot work any more.

Learning the code :(momentary)

Push the learning key on the receiver once time , it comes into momentary setting mode .
Wait for a moment , the LED will be off , it comes into learning state .
Push the remote button , LED indicator on the receiver board will flash then come off .
After 3 seconds, the LED indicator will be on again , learning successfully .

Learning the code : ( Toggle )

Push the learning key on the receiver twice time , it comes into toggle setting mode
Wait for a moment , the LED will be off , it comes into learning state .
Push the remote button,LED indicator on the receiver board will flash then come off.
After 3 seconds , the LED indicator will be on again , learning successfully .

Learning the code :( Latching )

Note: When you choose for latching mode , in order to learn more remote control , you need to
learn two different button , the first time learnt is for "ON", the second time learnt for "OFF".
For example : button A = ON , button B = OFF
Push the learning key on the receiver triple time , it comes into latching mode .
Wait for a moment , the LED indicator on the receiver board will flash then come off.
Push the remote button A .
LED flash for 5 times .
Push the remote button B .
Led flash for 5 times .
After 3 seconds , the LED indicator will be on again , learning successfully.
A = ON , B = OFF .
Upgraded Version 433Mhz 1CH RF Relay Receiver Universal
Wireless Remote Control Switch Module LED Light Controller
Description:

brand new and high quality.

Feature:

Long range working voltage.

Ultra low power, High sensitive response.

Application: Suitable for LED light, LED light string, Christmas tree light string, light control
switch and so on.

Light Switch Receiver Module only, other accessories demo in the picture is not included!

Specifications:

Item Type: Light Switch Receiver Module

Working Voltage: DC3.6-24V

Max Load: 2A

Static Current: 3.6-5.5mA

Working Frequency: 433MHz

Receiving Sensitivity: greater than and equal to -107dBm

Input: DC3.6V-24V

Output: DC3.6V-24V

Modulation System: ASK

Support code format: 1527 learning code

Number of stored remote controllers: less than and equal to 10

Working mode: inching, self-locking, interlock

Learning mode: Key Learning

Working temperature: -20-80 ℃/-4-176℉

Material: ABS+Metal

Size: Length: 11.5cm/4.5in

Color: As shown

Quantity: 1 Pc

Instruction:

About Working mode:

Momentary: Push the remote button , the relay connects, release the remote button , the relay dis-
connects.

Toggle: Push once the remote button, the relay connects , push twice the remote button , the
relay dis-connects.

Latching: Push the remote button A, the relay connects, push the remote button B, the relay dis-
connect.

Steps:

Clear Code: Press the learning button on the module 8 times continuously, and the light flashes
seven times and then goes out.

Momentary Mode：Press Module learning button 1 time, the indicator light is always on, then
press the remote control button, the indicator light flashes 3 times and then turns off , then the
learning is successful; If the code is not successful , the indicator lights out of the learning state
after 15 seconds.

Toggle Mode： Press the Module Learning button 2 times, the indicator light always turns on;
then press the remote control button, the indicator lights flicker three times and then off, then the
learning is successful; if the code has not been successful, the indicator lamp goes out of the
study state after 15 seconds.

Latching Mode：Press the Module Learning button 3 times, the indicator light always turns on;
and then press the buttons on the remote control , the indicator lights flicker three times and then
off,then the learning is successful; if the code has not been successful, the indicator lamp goes
out of the study state after 15 seconds.
Note:

No retail package.

Transition: 1cm=10mm=0.39inch

Please allow 1-3mm error due to manual measurement. pls make sure you do not mind before
you bid.

Due to the difference between different monitors, the picture may not reflect the actual color of
the item. Thank you!

Package Includes:

1 x Light Switch Receiver Module

 433.92Mhz Wireless RF Relay Receiver Module DC 3.6V 6V
12V 1CH Remote Control Switch and Transmitter for
Forward and Reverse DIY
Application environment:
Remote control switch,motorcycles, automobile anti-theft products, home security
products, electric doors, shutter doors, windows, remote control socket, remote control
LED, remote audio remote control electric doors, garage door remote control, remote
control retractable doors, remote volume gate, pan doors, remote control door opener,
door closing device control system, remote control curtains, alarm host, alarm, remote
control motorcycle remote control electric cars, remote control MP3.

Features:
 
*Wireless control LED lamp string, Christmas tree light string, light control switch.
*Long range working voltage.
*Ultra low power,High sensitive response.
Specifications Of The Receiver:
 
Working Voltage: DC 3.6V~18V.
Maximum Load: 3A.
Static Current: 3.6 mA ~ 5.5mA.
Working Frequency: 433MHz.
Reception Sensitivity: ≥ -107dBm.
Modulation Mode:ASK (superheterodyne).
Number Of Stored Remote Controls: ≤ 10.
Working Mode: Momentary, Toggle, Latching Mode.
Learning Style: Learning Button.
Working Temperature: -20 degrees 80 degrees.
  
Specifications Of The Receiver:
Operating RF Frequency: 433MHz.
Coded System: 1527 Learning Code.
Working Voltage: DC 6V.
Working Current: 12mA.
Transmitting Power: 10mW.
Wireless Operating Distance: 50m(Free Space).
Transmission Rate: 50 ~ 60KHz.
Frequency Deviation: ±0.2MHz.
Color: Black.
 Battery:2*CR2016

 
Wiring Diagram
 

 
Operating Mode
You can match the Transmitter with the Relay Receiver Module  in 3 modes.

Momentary Mode:

1. Press and hold one button, relay will turn on;

2. Release the button, this relay will turn off.

Toggle Mode:
1. Press button "A", relay will turn on;

2. Press button "A" again, this relay will turn off.

Latched mode:
1. Press button "A", relay will turn on;

2. Press button "B", this relay will turn off.

Delete the existing data about operating modes
Press the learning button (on the Receiver) 8 times. The existing data will be deleted
succeed.

Note:

1. When you receive our products, it may set in one remote mode randomly,
that because each product was tested before it can be arranged to shipment.
So, please delete the existing data to first use.

2. After deleted the data, all the remote controls cannot work any more.

Set up

Set up(Momentary)
1. Press the learning button(on the Receiver) once. Wait for 3 seconds;
2. Press one button on the remote control. Wait for 3 seconds. Succeed.

Set up(Toggle)
1. Press the learning button(on the Receiver) twice. Wait for 3 seconds;

2. Press one button on the remote control. Wait for 3 seconds. Succeed.
Set up(Latched)

1. Press the learning button(on the Receiver) third times. Wait for 3 seconds;

2. Press button "A" on the remote control. Wait for 3 seconds.

3. Press button "B" on the remote control. Wait for 3 seconds. Succeed.

* If you do not understand clearly. Please send us

a message to let us know. We will do our best to
service each of our customers. Enjoy your
shopping! *

=================================
Relay Remote Switch DC3.7V 4.2V 5V 6V
7.4V 8.4V 9V 12V Output 0V Dry Contact
Relay Switching Value NO COM NC
315MHz 433MHz
315mhz 433mhz for DC 3.7V LED Lamp Controller Micro Receiver Relay Wireless Remote
Control Switch Relay Remote Switch

brand new and high quality

Instructions:
Momentary--press one button is working /ON. loosen your finger on the same button is stop/OFF
.one channel switch need one buttons remote control
Toggle--press one button for one for time is working/ON .press the same button again is
stop/OFF .(one channel switch need one buttons remote control
Latched--press one button is working/ON ,press another button is stop/OFF. ( one channel
switchneed 2 buttons remote control )

Features:
Small size, low power consumption, flexible operation, easy to install.
Provide high signal sensitivity at lower cost and resist interference for excellent stability.
Remote Control only, other accessories demo in the picture are not included!

Specification:
Material: Plastic
Wide Range Working Voltage DC3.7V 4.5V 5V 6V 9V 12V
Max Load: 1A (have better Load less than 700mA)
Quiescent Current: 7mA
Relay Working Current: 20-30mA
Working Mode: Momentary Toggle Latched adjustable
Encoding Type: Learning Dot to add Transmitter
Normally Open Port (NO), Common Port (COM), Normally Close Port (NC)
Input: DC3.5V-12V
Output: 0V Switching Value
Frequency: 315MHz, 433MHz
Color: As Pictures Shown
Dimension: 2.4x1.1x0.7cm/ 0.94x0.43x0.28in
Quantity: 1 Pc

Note:
1.No retail package.
2.Please allow 0-1cm error due to manual measurement. plz make sure you do not mind before
you bid.
3.Due to the difference between different monitors, the picture may not reflect the actual color of
the item. Thank you!

Package includes:
1 x Receiver
000m High Power AC 220V 110V 1 CH 1CH
RF Wireless Remote Control LED Light Bulb
Strips Switch System,Transmitter + Receiver

2.4G 2.5G Wireless Switch Remote Kit 6

Channel Transmitter Receiver Module
Without Programming for DIY Onboard
Pair Button
Description
NOTE: You can also buy the 2.4G Wireless Switch Remote Kit SMD module (link) here :

The kit includes one pair of transmitter and receiver modules. And the frequency is 2.4GHz.
There is the MCU on board with built-in encoding and decoding code, pairing code.
When you do the remote control operation for the first time, you need to pair the transmitter and
receiver, and you do not need to do it again in the future.
It is easy to implement remote control without programming. It is very popular and easy for
remote control systems, such as wireless doorbell, remote control rolling gates, smart car, smart
home, etc.
Kit ini mencakup sepasang modul pemancar dan penerima. Dan frekuensinya 2.4GHz. Ada
MCU on board dengan kode encoding dan decoding built-in, kode pairing.
Saat Anda melakukan operasi remote control untuk pertama kalinya, Anda perlu memasangkan
pemancar dan penerima, dan Anda tidak perlu melakukannya lagi di masa mendatang.
Mudah untuk mengimplementasikan kendali jarak jauh tanpa pemrograman. Ini sangat populer
dan mudah untuk sistem kendali jarak jauh, seperti bel pintu nirkabel, gerbang bergulir kendali
jarak jauh, mobil pintar, rumah pintar, dll.
About Wireless Switch TX (will be abbreviated as TX module below):

- Switch number of channels: 6 channels

- Input ports: 6-channel key input, active low
- Working voltage: 2.5 - 3.6VDC
- Working Current: 0 - 15mA
- Working frequency: 2.4GHz
- MAX Transmission distance: 80 meters (open area)
- D1 LED: Each time you press the button will light up a time
- PAIR button: for pairing
- K1 ~ K6 buttons: Used to control 6 outputs of RX module, active low level
- Antenna: Built-in PCB antenna

About Wireless Switch RX ((will be abbreviated as RX module below):

- Switch number of channels: 6 channels
- Output port current: 2mA (max)
- Output mode: latch mode or non-latch mode
- Working voltage: 2.5 - 3.6VDC
- Exact Working frequency: 2.4GHz
- Working Current: 23mA
- Sensitivity: -85db
- PAIR button: for pairing
- Toggle switch on the board: used to switch the output mode, LATCH is the latch mode (only
press the button to change the output level), NON-LATCH is non-latch mode (press the button
light will be on, and release the button, the LED of RX module light goes off after 350
milliseconds)
- D1 ~ D6: Output LED, active high level output
- Antenna: Built-in PCB antenna
- Great for DIY
Pairing Process:
Step1: Power up for the two modules. Press and release the PAIR button of RX module, then D6
LED is on (tells it enters the pairing state). Press and release the PAIR button of TX module
within 10 seconds, then the D6 LED flashes for a while and keep the light on.
It is also possible to pairing this RX module with more TX modules (up to a total of 20).
Step2: Wait until D6 LED is off. You can press the K1~K6 button of TX module to test.
You can push the toggle switch on RX module to learn the difference between LATCH and
NON-LATCH output mode.
NOTE: A transmitter module can be paired with multiple receiver modules, and one
receiver module can only be paired with 20 transmitter modules.
Dimensions:
Photos

 
Part List (Schematics and program can be sent, Please contact us)

1 x Wireless switch transmitter module

1 x Wireless switch receiver module

        

Please Note That (Note: After you buy the product, the documents can be send,
Please contact us)
XY-WA XY-WB 2.4G 3.3V Wireless
Transceiver Module Long Distance Low
Power Anti-jamming LT8920 Ultra
NRF24L01 for Arduino STM PCB
XY-WA 2.4G Wireless Transceiver Module

XY-WB 2.4G wireless transceiver module

Feature:
Cost-effective 2.4G communication module, B version can be
soldered 2.54 pitch pin connection DuPont line for easy debugging,
A version can be directly inserted into the welding, reduce the
board volume, reduce the routing, suitable for toys, aircraft
models and other products transceivers.

Specification:
Operating Voltage: 2.2 -6.3V
Operating temperature: -40 -85°C
Emission current: 15-24mA
Receiving current: 18mA
Sleep current: 6uA

Package Included:
1 * 2.4G Wireless Transceiver Module
nRF24L01+ 2.4G Transmitter & Receiver
Wireless Module GWB T400 IIC SPI
Interface for Arduino Remote Control
Electric 150M 400M
Description: 
 
The module has applied the latest 2.4G wireless transmission technology
which features with stable and reliable performance, long communication
distance and strong anti-interference ability. It is suitable for the development
and application of toys, model airplanes and other products. 
 
Parameter: 
 
Working Voltage: DC 3.0V~3.6V 
GWB module: Support PA unidirectional gain amplifier Normal Working
Current: 30mA 
Instantaneous Emission Current: 340mA 
Pins space: 2.0mm 
Work Frequency: 2.4GHz 
T400 Transmission Distance: 400M T400 Receiving Distance: 150M GWB
Transmission Distance: 400M GWB Receiving Distance: 400M Work
Temperature: -20℃~85℃ 
Work Humidity: 0%~95%RH 
Using Steps: 1.Prepare the controller, such as for Arduino 2.Read
LT89xx(LT8900/LT8901/LT8902) datasheet 3.Write code by datasheet and
controller 4.Test 5.Note: GWB module supports PA unidirectional gain
amplifier.So the transmission distance is 400M, but the receiving distance is
50M. It is recommended to be used as a transmitter.
 
Package include:
 
1 x 150M/400M Transmitter & Receiver Wireless Transceiver Module
F Wireless Receiver and Transmitter Module
RX480E Transmitter Receiver Learning
Code 1527 for Arduino 433 Diy Electronic
Kit
Product description:
 
[Transmitter module ]
Product Model: TX118SA-4 (10 pack)
Transmitting power: 11dbm
Emission current: 10 mA
Rate of fire: maximum 10KB / S
Operating Voltage: DC 3V-24V
Encoding : EV1527 1527 Learning code
Each module has a unique address code, the address code of K1~K4 which are on the
same module is the same.
 
[Receiver module ] Product Model: RX480-E4 
Working Voltage : DC3.3~5V
Quiescent Current : ≤5mA
Output current : 10 mA
Working Frequency: 433MHz
Receive Sensitivity: -108dB
Working Temperature : -25~75
Working mode: Momentary Mode , self-locking (Toggle-Mode of the 4 Channels) ,
interlocking
The output: 4 channel CMOS level signal Corresponding to the remote control ABCD 4
buttons.
Pins Instruction
GND : ground or negative pole
+V : DC3.3~5V input
D0: Data output
D1: Data output
D2: Data output
D3: Data output
VT: Output
 
How to match the transmitter and receiver
 
1. Delete existing data: Press learning button(on the receiver) 8 times. Response: LED
flashes 7 times.
2. Learning remote code: press learning button(on the receiver) once, twice or three
times (see below).
LED turns on: learning mode is active. Press any button of the remote control.
LED indicator flashes three times: learning successfully completed.
3. Test: after the above operation , the receiver board can be controlled by the remote
control.
More transmitters with different IDs can be learned and stored additionally, starting with
step 2.
A mixture of different modes is possible.
 
Button usage (sets mode and starts pairing process):
Press once: Inching mode (Momentary Mode)
Press twice: self-Lock Mode (Toggle-Mode of the 4 Channels)
Press three times: interlocked mode (selected channel active and be
cleared, if another channel becomes active) 
active) 
Thinary VL53L0X Time-of-Flight (ToF)
Laser Ranging Sensor Breakout 940nm GY-
VL53L0XV2 Laser Distance Module I2C IIC
3.3V/5V
Descriptions:

The VL53L0X from ST Microelectronics is a time-of-flight ranging system integrated into

a compact module. This board is a carrier for the VL53L0X, so we recommend careful
reading of the VL53L0X datasheet (1MB pdf) before using this product.  

The VL53L0 uses ST's FlightSense technology to precisely measure how long it takes
for emitted pulses of infrared laser light to reach the nearest object and be reflected
back to a detector, so it can be considered a tiny, self-contained lidar system. This time-
of-flight (TOF) measurement enables it to accurately determine the absolute distance to
a target without the object's reflectance greatly influencing the measurement. The
sensor can report distances of up to 2 m (6.6 ft) with 1 mm resolution, but its effective
range and accuracy (noise) depend heavily on ambient conditions and target
characteristics like reflectance and size, as well as the sensor configuration. (The
sensor's accuracy is specified to range from ±3% at best to over ±10% in less optimal
conditions.)  

Ranging measurements are available through the sensor's I2C (TWI) interface, which is

also used to configure sensor settings, and the sensor provides two additional pins: a
shutdown input and an interrupt output.  

The VL53L0X is a great IC, but its small, leadless, LGA package makes it difficult for the
typical student or hobbyist to use. It also operates at a recommended voltage of 2.8 V,
which can make interfacing difficult for microcontrollers operating at 3.3 V or 5 V. Our
breakout board addresses these issues, making it easier to get started using the
sensor, while keeping the overall size as small as possible.  
 
PIN     Description  
VDD  Regulated 2.8 V output. Almost 150 mA is available to power external
components. (If you want to bypass the internal regulator, you can instead use this pin
as a 2.8 V input with VIN disconnected.)
 
VIN  This is the main 2.6 V to 5.5 V power supply connection. The SCL and SDA level
shifters pull the I2C lines high to this level.
 
GND  The ground (0 V) connection for your power supply. Your I2C control source must
also share a common ground with this board.
 
SDA    Level-shifted I2C data line: HIGH is VIN, LOW is 0 V
 
SCL      Level-shifted I2 C clock line: HIGH is VIN, LOW is 0 V
 
XSHUT    This pin is an active-low shutdown input; the board pulls it up to VDD to
enable the sensor by default. Driving this pin low puts the sensor into hardware standby.
This input is not level-shifted. 
5V Mono Stereo Receiver Audio Voice
Module Bluetooth Output Universal 7 PIN
Output Interface Speaker Amplifier Board
Notice :There is a default tone when pairing and it cannot be modified.The actual product, the
pin has been welded, the default is 90 degree curved needle, or you do not need welding pin or
need to weld straight needle, please contact customer service!
Port description:
 
1. +5V power supply: connect the positive pole of the power supply, the voltage range is
4.1V~5V, please ensure that the power supply is within this range. Exceeding this range may
damage the module or cause the work to be abnormal;
2, ground: GDN is connected to the negative pole of the power supply, which is also the ground
of audio. This place must be separated from the ground and the audio ground separately.
3. Left channel: Connect the left channel input of the power amplifier board or the left channel of
the earphone. It is recommended to connect a capacitor to the output port (depending on the
input matched by the power amplifier);
4. Right channel: Connect the right channel input of the power amplifier board or the right
channel of the earphone. It is recommended to connect a capacitor to the output port (depending
on the matching input of the power amplifier);
5, mute output port: the port is preset to a high level, when the mute, the port outputs a low level;
6. Status indicator: When the Bluetooth is not connected, the light flashes quickly, and once the
Bluetooth connection is successful, it will flash slowly;
7. Reserved port: The port has been pulled up to 5V. When the port is triggered by a low level, it
will be turned off. When the port is turned back to the low level again.
 
Please Note: From the Bluetooth audio module to the power supply or to the audio interface,
please use the soldering method, do not use the way of plugging, the contact resistance will
introduce noise.
 
Precautions:
 
1. Power supply: The Bluetooth audio module is a circuit sensitive to high-frequency
interference. It is recommended to use a linear regulated power supply. If DC-DC power supply
is used, please add LC filter to reduce the harmonic interference of the power supply, especially
the switch such as mobile phone charger. Power supply, power supply ripple may cause
Bluetooth to not connect properly, and this type of 5V output is often between 5.1V and 5.4V,
exceeding the working voltage of the Bluetooth audio module;
When using a switching power supply such as a mobile phone adapter, please add this power
supply circuit, the inductance can not be added.
 
2. Grounding: Since the audio signal is sensitive to the interference caused by the grounding
point, two grounding knots can be soldered on the output pin of the Bluetooth module, one is
connected to the negative pole (GND) of the power supply, and the other is connected to the
power amplifier board. Audio input ground, try to solder on the circuit board, do not use lead
wire connection (susceptible to interference), and it is recommended to try the grounding point to
minimize interference;
 
3, Antenna interference: Bluetooth antenna is extremely vulnerable to high frequency, or strong
electromagnetic signal interference, relatively far away from the strong signal of the power
amplifier board, and the antenna can not be close to metal objects, to maintain a certain distance;
 
4, The outer casing shielding: because the metal casing of the casing has a shielding effect on the
Bluetooth signal, it may attenuate the Bluetooth signal to cause poor reception, please keep the
corresponding opening, or exposed.
Note: For some power amplifier boards that are susceptible to interference and interference is not
easy to handle, please separate the power supply, that is, the power amplifier board is powered
by one power supply, and the Bluetooth module supplies power all the way.
 
Common problem handling:
 
1, Current sound:
The cause is caused by ground interference. It is recommended that the output terminals of the
Bluetooth module do not need to be soldered with the output terminals of the plug-in. In
particular, the ground wire should be soldered, and the line should not be too long. The shorter
the better, the thicker. In the ground wire drawn from the Bluetooth module, the power ground
and the audio ground must also be separated, and it is not possible to connect only one ground
wire. The problem of audio grounding at the grounding point of the power amplifier board must
be connected to the ground of the audio input of the power amplifier. This grounding point can
be tried to solder at different positions to achieve the lowest current sound. Separate power
supply is a better way to solve this current sound.
 
2. The Bluetooth signal is weak:
When the module can work normally, the Bluetooth indicator light flashes normally. The
receiving distance of Bluetooth is very close, it can't exceed 5 meters. Generally, there is
interference in the power supply (switching power supply interference), or the power supply
voltage is abnormal. Please refer to the processing switch of the document. Add that diode and
capacitor when the power supply interferes. ``
 
3, Bluetooth can not find the signal:
An important reason for not finding the Bluetooth signal is that the power supply is caused.
Except that the power supply voltage is abnormal, the ripple of the power supply is generally too
high, causing great interference to the high-frequency signal of the Bluetooth module. The
method can be handled. In another case, the same mobile phone is connected to multiple
modules. Although the Bluetooth numbers are the same, but the internal addresses are different,
you can delete the original Bluetooth number and then search for the connection.
 
4, Noise processing:
There are two kinds of noise reduction, one is the inherent noise of the Bluetooth processing
standby search signal, but the sound is not very large, only a little bit, it may be processed by
muting (MUTE). Another type of noise floor is caused by interference or wiring, and the
modified line can be solved by improving the grounding point. It can be handled in accordance
with the method described above.
 
I2C ADS1115 16 Bit ADC 4 channel Module
with Programmable Gain Amplifier 2.0V to
5.5V for Arduino RPi
For microcontrollers without an analog-to-digital converter or when you want a higher-
precision ADC, the ADS1115 provides 16-bit precision at 860 samples/second over I2C.
The chip can be configured as 4 single-ended input channels, or two differential
channels. As a nice bonus, it even includes a programmable gain amplifier, up to x16, to
help boost up smaller single/differential signals to the full range. We like this ADC
because it can run from 2V to 5V power/logic, can measure a large range of signals and
its super easy to use. It is a great general purpose 16 bit converter.
 
The chip's fairly small so it comes on a breakout board with ferrites to keep the AVDD
and AGND quiet. Interfacing is done via I2C. The address can be changed to one of
four options (see the datasheet table 5) so you can have up to 4 ADS1115's connected
on a single 2-wire I2C bus for 16 single ended inputs.
 
 
 
WIDE SUPPLY RANGE: 2.0V to 5.5V
LOW CURRENT CONSUMPTION: Continuous Mode: Only 150μA Single-Shot Mode:
Auto Shut-Down
PROGRAMMABLE DATA RATE: 8SPS to 860SPS
INTERNAL LOW-DRIFT VOLTAGE REFERENCE
INTERNAL OSCILLATOR
INTERNAL PGA
I2C INTERFACE: Pin-Selectable Addresses
FOUR SINGLE-ENDED OR TWO DIFFERENTIAL INPUTS
PROGRAMMABLE COMPARATOR
This board/chip uses I2C 7-bit addresses between 0x48-0x4B, selectable with jumpers.
 
+- 5V 6V 9V 12V 15V 24V Positive &
Negative Dual Output power supply DC DC
Step-up Boost Converter module
 

Click on the picture or search SKU for product details

We are a professional manufacturer, if you don't find the product you need, please contact us directly.

Product SKU Click Picture Description

Input voltage : DC +3~+15V,

Boost-Buck
 DD0315NA     Output : DC -3.3V -5V -6V -9V -12V -15V;
+ to - voltage
Maximum output current : 180-500MA

Input voltage : DC +4.8V-+28V,

Boost-Buck
DDUB12NA Output : DC -5V/-10V/-12V/-15V;
+ to - voltage
Maximum output current : 250-500MA

Input voltage : DC +3~+18V,

Boost
DD1718PA Output : DC ±5 ±6 ±9 ±12 ±15 ±24
+ to +/-voltage
Maximum output current : 100-200MA

Input voltage : DC +3.6~+30V,

Boost-Buck 
 DD39AJPA Output : DC ±3~±30V adjustable
+ to +/-voltage
Maximum output current : 200-3000MA

Input voltage : DC +3~+24V,

Boost-Buck
DD1912PA Output : DC ±5V/±6V/±9V/±10V/±12V/±15V
+ to +/-voltage
Maximum output current : 100-1000MA

Input voltage : DC +-3.5~+-20V,

 1% +/-voltage
ZD3605PA Output : DC ±2.5V ±3.3V ±5V ±7.5V ±10V ±
 reference Module
Maximum output current : 14MA

 
 
 
Product Name:  +- 5V 6V 9V 12V 15V 24V Positive & Negative Dual Output
power supply DC DC Step-up Boost Converter module
   
Packing list:
  
1 PCS Positive and negative voltage Dual voltage DC DC Boost Converter Module
 
Description:
 
±5V :
Input voltage DC 3 ~ 4.5V,output DC ±5V(Deviation is ±5%) 
Maximum input current 2A
Maximum output current : +Vo is 1A,-Vo is 200mA
 
±6V :
Input voltage DC 3 ~ 5V,output DC ±6V(Deviation is ±5%) 
Maximum input current 2A
Maximum output current : +Vo is 1A,-Vo is 200mA
 
±9V :
Input voltage DC 3.3~ 8V,output DC ±9(Deviation is ±4%) 
Maximum input current 1.8A
Maximum output current : +Vo is 800mA,-Vo is 180mA
 
±12V :
Input voltage DC 3.3~ 11V,output DC ±12(Deviation is ±4%) 
Maximum input current 1.8A
Maximum output current : +Vo is 700mA,-Vo is 150mA
 
±15V :
Input voltage DC 3.3~ 13V,output DC ±15(Deviation is ±4%) 
Maximum input current 1.8A
Maximum output current : +Vo is 600mA,-Vo is 120mA
 
±24V :
Input voltage DC 3.6~ 18V,output DC ±24(Deviation is ±4%) 
Maximum input current 1.8A
Maximum output current : +Vo is 400mA,-Vo is 100mA
  
Quiescent current: 3-4mA
DC DC Boost Converter Module working frequency 400kHz.
Operating temperature range : -40~+125 Degrees Celsius
Storage temperature range : -65~+150 Degrees Celsius
2.54mm pin pitch,for MCU Development Board Breadboard friendly.
Size : 25 x 16.3 x 6.6mm
Weight :with Pin 3.4g,no Pin 3g
   
Internal Optimize Power MOSFET 
High efficiency up to 90% 
Built in Frequency Compensation
Built in Soft-Start Function 
Built in Thermal Shutdown Function 
Built in Current Limit Function 
      
Note:
1 Due to the diode partial pressure, the voltage of -Vo is lower than +Vo
2 In order to obtain a more stable voltage, it is recommended that the output is greater
than 15MA
3 -Vo cannot be used alone, or no voltage output.But you can just use +Vo  
  
 
Applications
  
ADC/DAC/Operational Amplifier 
RS232 RS485 RS422 Bus
Audio equipment
LCD power supply
Instrumentation equipment
MCU Board
Motor Power
Instrumentation multimeter
Wifi/Router/Ethernet devices 
    
Attention :
    
This is a DC-DC voltage converter module,Must be noted when using:
1 Input voltage can not be greater than the maximum input range
2 Output power can not be greater than the maximum load for a long time
3 Input power must be greater than the output power, because the power
consumption of the module itself
  
Q & A:
  
Q : Why output voltage is less than the nominal voltage
A : Input power supply power is too low.Test the input voltage with a multimeter,a
t this time of the input voltage is very low
 

Click on the picture or search SKU for product details

We are a professional manufacturer, if you don't find the product you need, please contact us directly.
Product SKU Click Picture Description

Input voltage : DC +3~+15V,

Boost-Buck
 DD0315NA     Output : DC -3.3V -5V -6V -9V -12V -15V;
+ to - voltage
Maximum output current : 180-500MA

Input voltage : DC +4.8V-+28V,

Boost-Buck
DDUB12NA Output : DC -5V/-10V/-12V/-15V;
+ to - voltage
Maximum output current : 250-500MA

Input voltage : DC +3~+18V,

Boost
DD1718PA Output : DC ±5 ±6 ±9 ±12 ±15 ±24
+ to +/-voltage
Maximum output current : 100-200MA

Input voltage : DC +3.6~+30V,

Boost-Buck 
 DD39AJPA Output : DC ±3~±30V adjustable
+ to +/-voltage
Maximum output current : 200-3000MA

Input voltage : DC +3~+24V,

Boost-Buck
DD1912PA Output : DC ±5V/±6V/±9V/±10V/±12V/±15V
+ to +/-voltage
Maximum output current : 100-1000MA

Input voltage : DC +-3.5~+-20V,

 1% +/-voltage
ZD3605PA Output : DC ±2.5V ±3.3V ±5V ±7.5V ±10V ±
 reference Module
Maximum output current : 14MA

 
 
 

 
AT-09 Android IOS BLE 4.0 Bluetooth
module for arduino CC2540 CC2541 BLE
Serial Wireless Module compatible HM-10
HM-11
MAX9812 Microphone Amplifier Sound MIC
Voice Module for Arduino 3.3V/3.5V
Product Description

This module above a professional microphone amplification IC, low output noise, small size,
high sensitivity, fixed gain at 20dB, support 3.3v and 5v two power supply.
 
Voltage: 3-5V
 
OUT Output: The default output analog signals.
 
Size: 15mm * 9mm

 
 

 
1Set I2C SMBUS INA3221 Triple-Channel
Shunt Current Power Supply Voltage
Monitor Sensor Board Module Replace
INA219 With Pins
Description:
 
 
The INA3221 is a three-channel, high-side current and bus voltage monitor
with an I2C- and SMBUS-compatible interface. The INA3221 monitors both
shunt voltage drops and bus supply voltages, in addition to having
programmable conversion times and averaging modes for these signals. The
INA3221 offers both critical and warning alerts to detect multiple
programmable out-of-range conditions for each channel.
 
The INA3221 senses current on buses that can vary from 0 V to 26 V. The
device is powered from a single 2.7-V to 5.5-V supply, and draws 350 µA (typ)
of supply current. The INA3221 is specified over the operating temperature
range of –40°C to +125°C. The I2C- and SMBUS-compatible interface
features four programmable addresses.
 
 
Features
 
Senses Bus Voltages From 0 V to 26 V
Reports Shunt and Bus Voltage
High Accuracy:
Offset Voltage: ±80 µV (max)
Gain Error: 0.25% (max)
Configurable Averaging Options
Four Programmable Addresses
Programmable Alert and Warning Outputs
 
Power-Supply Operation: 2.7 V to 5.5 V
 
 
 

 
 
INA219 I2C interface High Side DC Current
Sensor Breakout power monitoring sensor
module
This breakout board will solve all your power-monitoring problems. Instead of struggling
with two multimeters, you can just use the handy INA219B chip on this breakout to both
measure both the high side voltage and DC current draw over I2C with 1% precision.
 
Most current-measuring devices such as our current panel meter are only good for low
side measuring. That means that unless you want to get a battery involved, you have to
stick the measurement resistor between the target ground and true ground. This can
cause problems with circuits since electronics tend to not like it when the ground
references change and move with varying current draw. This chip is much smarter - it
can handle high side current measuring, up to +26VDC, even though it is powered with
3 or 5V. It will also report back that high side voltage, which is great for tracking battery
life or solar panels.
 
A precision amplifier measures the voltage across the 0.1 ohm, 1% sense resistor.
Since the amplifier maximum input difference is ±320mV this means it can measure up
to ±3.2 Amps. With the internal 12 bit ADC, the resolution at ±3.2A range is 0.8mA. With
the internal gain set at the minimum of div8, the max current is ±400mA and the
resolution is 0.1mA. Advanced hackers can remove the 0.1 ohm current sense resistor
and replace it with their own to change the range (say a 0.01 ohm to measure up 32
Amps with a resolution of 8mA)
 
We include a 6-pin header (so you can easily attach this sensor to a breadboard) as
well as a 3.5mm terminal plug so you can easily attach and detach your load. Usage is
simple. Power the sensor itself with 3 to 5VDC and connect the two I2C pins up to your
microcontroller. Then connect your target power supply to VIN+ and the load to ground
to VIN-
 
TECHNICAL DETAILS
 
Uses the INA219B chip, see datasheet for detailed specifications
0.1 ohm 1% 2W current sense resistor
Up to +26V target voltage
Up to ±3.2A current measurement, with ±0.8mA resolution
0.9" x 0.8" PCB
This board/chip uses I2C 7-bit addresses 0x40, 0x41, 0x44, 0x45, selectable with
jumpers
 
NA219 can be achieved within the maximum error accuracy 85C
temperature range from -40C to + 1% ,
the maximum offset is 100 uV.
The high-precision products combine the advantages of 12-bit
resolution.
This module can be sensed bus voltage range is 0 V to +26 V.
Features:

Package:SOT23
Working Voltage 3~5V
Size:25.5 x 22.3mm
Used for I2C port zero drift / bidirectional current / power
monitoring sensor module

SX1276 SX1278 ESP32 LoRa

868MHz/915MHz/433MHz 0.96 Inch Blue
OLED Display Bluetooth WIFI Kit 32
Development Board
Description
Dominant Frequency: 240MHZ
Flash: 32M-Bits
Processor: Tensilica LX6 Dual Core
Master chip: ESP32
LoRa chip: SX1276 SX1278
Support frequency band: 868-915MHZ/433MHz
Open communication distance: 2.8KM
Computing capacity: up to 600DMIPS
Dual-mode Bluetooth: traditional Bluetooth and BLE low-power Bluetooth
Development environment: perfect support for Arduino
Operating voltage: 3.3-7V
Operating temperature range: -40-90 °
Receiver sensitivity: -139dBm (SF12, 125KHZ)
UDP continuous throughput: 135Mbps
USB adapter chip: CP2102
Support mode: Sniffer, Station, softAP and Wi-Fi Direct
Transmit power: 19.5dBm@11b, 16.5dBm@11g, 15.5dBm@11n
Data rate: 150Mbps @ 11n HT40, 72Mbps @ 11n HT20,
54Mbps @ 11g, 11Mbps @ 11b
Specifications
 Operating voltage: 3.3 – 7 V
 Operating temperature range: -40 to 90°C (-40 to 194°F)
 Support for Sniffer software protocol analysis, Station, SoftAP, and Wi-Fi Direct
modes
 Data rates: 150 Mbps @ 11n HT40, 72 Mbps @ 11n HT20, 54 Mbps @ 11g, 11
Mbps @ 11b
 Transmit power: 19.5 dBm @ 11b, 16.5 dBm @ 11g, 15.5 dBm @ 11n
 Receiver sensitivity up to -98 dBm
 UDP sustained throughput: 135 Mbps
Github
 https://github.com/Xinyuan-LilyGO/LilyGo-LoRa-Series

Reminders
 
- The 868/915 MHz antenna needs to be connected with the IPEX interface.
- When the battery is full, the blue LED will stop working.
- When using, pay attention to “+” and “-” of the battery.
- With the IO port touchscreen Touch signal input, you need to add the 100nF pull-down
capacitor to this pin.
- Red light: power indicator
- Blue light: IO25 programmable control

Reminder: This product does not include the battery.

868/915MHz CH910
1 x LILYGO LoRa32 V1.0 (8
1 x Power cable (Jst 2pin 1
1 x LoRa Antenna

2 X 2.54mm Male Pin（1*1

868/915MHz CH910
2 x LILYGO LoRa32 V1.0 (8
2 x Power cable (Jst 2pin 1
2 x LoRa Antenna

4 X 2.54mm Male Pin（1*1

Linear Conversion Voltage to Current
Transmitter Signal Module 0-5V to 4-20mA
DC 12V-24V Isolated Board
Description:
Voltage switch current module can convert 0-5V voltage signal into 4-20mA current
signal.
In the process of signal transmission circuit voltage signal will become weak with
transmission Distance increased, the transmission can be avoided using weak electric
current signal.
Specification:
Power supply voltage: DC 12V -24V
Input voltage signal: 0 -2.5V, 0 -3.3V, 0 -5V 0 -10V, 0 -15V, 0 -24V(Optional)
Output current: 4-20mA, 0 -20mA(Optional)
Module size: 5.5*2.5cm
Zero and span can be adiusted (potentiometer adjustment).
With the isolated nature of the non-optically isolated.

Package Included:
1 x Voltage to Current Transmitter Signal Module
PCF8574 PCF8574T I/O for I2C Port
Interface Support Cascading Extended
Module
Description:
 
Module function:
This is the I/O extended module, which use for I2C interface, you can use two of the module to
extend 8 I/O. Support cascading, and you can use at most 8 modules to extend 64 I/O at the same
time. Can be changed the address by set toggle switch
PCB Size: 36 x 16mm/1.41*0.62"
Every 2 seconds, make P0-P7 port output High level, Low level, and put 3 toggle switches to
ON, the address of module is 0x27
Massduino Core MD-328D Mini Module R3
Onboard LDO for Arduino Relay DAQ IOT

MassDuino UNO Core

    Lower Price
    Arduin IDE Support
    Highly compatible to UNO R3
    32KB Flash 2KB RAM
   10/12/16Bit ADC 
/*======================================================
        analogRead()           // 10bit ADC, Compatible to UNO R3
     analogRead_12bits() // 12bit ADC , 130 sps
      analogRead_16bits() // 16bit ADC , 125 sps
======================================================*/

  Chip level support (MD-328D IC for mass purchase,click to view)

Easy for prototype development , directly use for mass
production!

Features

    MD-328D core module

Standard USB2Serial interface for uploading and debugging
Onboard 2.4GHz RF Module (Optional)
100% Arduino development environment
Vertical double row connector, minimum size on the main board
Full UNO IO supported

Parameters

    MCU: MD-328D 32K Flash 2K SRAM 10bit ADC

Working Voltage : 3.3V with onboard LDO
Input Voltage: DC 4.5 to 12V
3.3V Output Current : 300mA MAX
PCBA Size: 20 x 35mm
Bootloader preprogramming : Arduin UNO R3

Application Schematic

    This schematic is demonstrated how to using UNO Core create 3-ch analog voltage ,
here we need a PWM to DAC module DAC-3000 , UNO Core use AnalogWrite function
to create 3 ch PWM signal and DAC-3000 will converter the PWM to analog output , the
output is: Vout = (1-PWM%) * Vref . in here the DAC output range is 0 to 3.3V.
The Pin24 (VCC_3V3) connected onboard LDO’s output, it will share 3.3V with the
module circuit , so the VCC_3V3 Load current have to limited within 300mA , otherwise
it will lead the 3.3V unstable , or damaged the module.
The UNO Core have a onboard RF module design(LC-2000,Clik to View) , the LC-2000
is a 2.4GHz RF UART module , it can be make UNO Core communication via 2.4GHz
RF connection, but not all version will be install this module, Please notice the
description, we have module number as below:
UNO Core    :  without RF Module
RF UNO Core  :  with RF Module(Click to View)

Upload sketch and communication

    RF UNO Core can be uploading sketch and communication via 2.4GHz RF

connection , user need a USB Dongle on PC side and we call it LC-2000U , we will
release this product in Jan.2016.
Both RF UNO Core and UNO Core have a onboard UART connector , it’s a 6-Pin
2.0mm Female connector, user can be use stand USB2Serial Light cable to upload and
communication with a 2.5mm to 2.0mm convertor. We also provide UC-2102 kit for this
usage.

Package List

    1 x MassDuino UNO Core

All of the PCBAs have  passed 130 items testing by 100% automatic, 100% quality
guarantee.

Pin Descriptions
LC-2000PA-P2P 2.4G RF Module UART
115Kbps Remote Upload Sketch RF UART
TTM RS-232 for Arduino UNO Mega2560
STM32 MCU ARM
Features
1, Low Cost , easy to use , zero RF knowledge request for wireless communication design.

2, Transparent Transmission Mode (TTM), save MCU resource, implement wireless

communication over the wired UART programming.

3, Per to Per communication (P2P)

4, Full duplex working , max support baud rate 512Kpbs.

5, Max continuous bi-direct baud rate up to 115Kbps.

6, DTR signal support used for Arduino for remote upload sketch.

7, Power Save Mode (PSM) current consumption down to.

8, Sleep mode current consumption down to 150uA.

9, LC-2000-P2P: 0dBm, Low power , 20 to 30m distance

LC-2000PA-P2P: 20dBm , 200 to 300m distance

The RF communication is very depended on it’s working environment, the distance is out door
clear environment and only for reference.

Pin Description
Important Notes:

The LC-2000(PA)-P2P serial module is working under per to per mode , a Pairs of LC-2000(PA)-
P2P has contained two unis , one is MASTER and the other one is SLAVE, the module will mark it
on it’s label.

LC-2000(PA)-P2P Working Mode

The LC-2000(PA)-P2P have below working modes:

1, Normal mode:
In this mode, the module will be standby after power on , user can be sent or receive data at
any time, this mode have least delay and highest power consumption, this mode can be used
on minimum data delay request applications.

2, Power Save Mode (PSM):

In this mode , module will be working on 10% proportion of intermittent mode, user can be
sent data at anytime but other side maybe receive data a little bit delay , the delay time is
depended on the working mode of receive side, the max delay time is 2sec.
This mode only consumption 10% of power and also ensure the data transmission with a little
bit delay.

3, Sleep Mode:
In this mode , the module will stay in sleep mode , it will not sent or receive any data , user need
to pull “FUN” pin low to wake up the module , and then send data , after data transmitted the
module will be going to sleep mode again, this mode have minimum power consumption but
user need to make application protocol to ensure communication ok.
The module will be delivered with Normal mode , user can be switch the mode by config
command.

Pairing

Before using the module , user need to pairing it , then the

module can be communication to each other , to pairing the
module , user need to notice beow:

1, Only one MASTER and one SLAVE can be pairing.

2, To Pairing the module , press and hold the “PAIRING” button one the moude , or pull the
“FUN” pin low and hold it over 3sec , the module will be entry PAIRING mode , the LED will be
flash to indication the status.

3, Do same thing on other side, once both module entry PAIRING mode , they will be pair very
quickly and the LED will be OFF , that mean the module is paired and ready to communication
to each other.

4, One MASTER only can paired with one SLAVE and the smae for SLAVE , that means if one
module paired with a new module , the old paired module will be lost paired and they will not
communication anymore.

5, To ensure the module was paired , pull low the DTR pin of MASTER side , the SLAVE side will
be follow the status, please note that the DTR is unidirectional working , that means only the
SLAVE’s DTR pin follow the MASTER ‘s DTR status.

If you sent configuration command after pull low the FUN pin , the module will entry CONFIG
mode , not PAIRING mode .

Configuration Command

If user to configuration the module , user need to pull “PAIR/CFG” pin low , module will be entry
CONFIG mode , then sent configuration command via TXD , after configuration , pull “PAIR/CFG”
pin high. The timing as below:

In CONFIG mode , user can be sent command with any baud rate , the module will auto apply
the baud rate , after exit the CONFIG mode , the module will apply baud rate as the
configuration data (may be difference as the CONFIG mode).

The configuration command is full text mode, the format as below:

Fixed token: “=”
Command Value: 3 digitals with ASCII character (Range 000 to 999)
Fixed separators : “:”
Parameter: max 240 ASCII character
Fixed end symbol: “\r\n”

For example:

MCU send command to LC-2000-P2P: =”800:\r\n” // Read local UID

LC-2000-P2P reponce: =”=800:100.000.000.001\r\n” // This module’s UID is : 100.000.000.001

The detailed command list as below:

Remote upload sketch for Arduino

INHAOS released some Arduino product without USB connect , we call it LITE version , for those
module , it’s very easy to connected to LC-2000(PA)-P2P, the module include: BUONO UNO R3
LITE and BUONO UNO LC LITE and Mega2560-Core and so on.

If the Slave side working in Sleep mode, you need to wake up the Slave by press the “FUN” pin
for 100mS, then you can uploading sketch.

To Uploading sketch , the operation is same as the wired connection uploading operation.
Bulk data transmission

When you transmission bulk data via LC-2000(PA)-P2P, please combined the BUSY pin , to
ensure the data integrity.

About the Busy pin

We setup a pin named “Busy” , in fact it’s a multi function pin. The onboard LED is indication the
Busy Pin status, when Busy pin is high (3.3V) , the LED will be light.

1, After power up the module , if the module is paired and other side also power ON , the LED
will be turned off , in this case , user can be sent and read data at any time.

2, If module did not paired , after power on , the LED will be light , in this case , user can not
sent data , until one user pair to another module and both module is powered.

3, If module is paired , but other side did not powered , the LED also be light , in this case , user
need to powered other side and the LED will be turned off.

4, When user long press “PAIR” button (pull PAIR/CONFG low) , the module will be entry
PARRING mode , in this case , the LED will be flash , and it will be turned off after paired. To
paired two module , user need to make two module entry PAIRING mode .

5, The LED will be light during transmit or receive data , and will be turned off after finish data
transmit or receive, if the LED is always on , it means the data is not completed transmit , or RF
connection is lost.
In the application, user can be read the BUSY pin status by a GPIO.

About the PAIR/CFG pin

The PAIR/CFG pin have two function , one onboard tack switch is connected to this pin , when
press the switch , the pin will be pull low , here have to function for this pin:

1, Config module parameter: pull low the “PAIR/CFG” pin , and sent config command within
100mS , the module will be entry config mode , after config finish , pull this pin high , the
module will be entry TTM (Transparent Transmission Mode),
Please notes , during PAIR/CFG pin is low , all data will be process as command , valid command
will be execution and invalid command will be discard , the data will not sent to other side.
During PAIR/CFG pin is high , all data will be process in TTM and sent to other side, it will not
execution config function even it’s valid format command.

2, Enter PARING mode: long press the button, the module will be entry PAIRING mode , in this
mode , the LED will fast flash until paired , and then the module will be exit PARING mode and
back to TTM mode.

About Remote Upload sketch

The remote upload sketch is a very special function of LC-2000(PA)-P2P, this feature support
stand Arduino and the operation is very simple, in arduino system , the DTR pin is connected to
RESET pin of the MCU via a capacitor , if user need to upload sketch , the Arduino IDE will be
pull low the DTR pin , the RESET will get a negative pulse and the MCU will be reset and enter
bootloader mode, then IDE will sent sync word to MCU , the MCU sent ACK and then Arduino
IDE will start a data transmission.

The LC-2000(PA)-P2P will sent DTR signal from Master to Slave side , this will allow user to
upload sketch by remote , most RF module like Bluetooth UART / WIFI UART can not support
this function.

To implement this feature , user need to connected Master to PC side ,and Slave to Arduino
side, and the periphery of the necessary parts in DTR to RESET patch is required.

The BUONO UNO R3 LITE and BUONO UNO LC LITE and Mega2560-Core is not included USB to
UART chip , It will very easy to connect to LC-2000(PA)-P2P and implement remote upload
sketch feature.

Package List

1 x LC-2000PA-P2P Master
1 x LC-2000PA-P2P Slave
2pcs 4 WIRE L298N L9110 1.5A 2.5A 2 way
DC Motor Driver Drive Module PWM Speed
Dual H-Bridge Stepper Board MOS Switch
motor drive module is ideal for use in battery-powered smart car, toy cars,
robots. Supply voltage 2V ~ 10V, can drive two DC motors or a 4-wire 2-
phase stepper motors ,can achieve forward rotation or reverse rotation, it is
possible to adjust the rotation speed. Each can provide continuous current
of 1.5A, peak current up to 2.5A, thermal protection and can be
automatically restored.

Product Highlights:

Useof imported original chip, built-in low on-resistance MOS switch, minimal
heat, no heat sink, small size, low power consumption, is ideal for battery
powered.

(L298N internal transistor switch, low efficiency, high fever, need to add
heat sink, bulky, L298N very easy to burn).

Dual 1.5A * 2, the peak current to be 2.5A, built-in thermal protection

circuit, do not be afraid motor stall burned, automatic recovery after the
temperature dropped.

Small size, light weight, 0 standby current, is the ideal choice for your car
model.

Product parameters:

Dual H-bridge motor driver, can drive two DC motors or a 4-wire two-phase
stepper motor.

The module supply voltage 2V-10V.

Signal input voltage 1.8-7V.

Single Operating current 1.5A, peak current up to 2.5A, low standby current
(less than 0.1uA).

Built-in common conduction circuit, when the input pin is left floating, the
motor does not malfunction.

Built-in thermal protection circuit with hysteresis effects (TSD), without

worrying about motor stall.

Product Size: 24.7 * 21 * 5mm (length, width, height), ultra-small size.

The mounting hole diameter: 2 mm.

Precautions:

1. Power positive and negative reversed will certainly cause damage to the
circuit.

2. Output is shorted to ground or output short circuit, and the motor stall,
the chip will heat protection, but in the near or exceeding 10V voltage and
peak current is greater than 2.5A situation can also cause chip burned.

NO Retail Box. Packed Safely in Bubble Bag.

Package Included:

2 x  1.5A 2-way DC Motor Driver Module PWM Speed Dual H-Bridge Stepper
L298N

5V-12V DC Brushless Driver Board

Controller For Hard Drive Motor 3/4 Wire
New G08 Whosale&DropShip
1Pc 5V-12V DC Brushless Driver Board Controller For Hard Drive Motor 3/4 Wire

brand new and high quality

Material: Plastic and Electrical components
Color: Green and Black
The driver board can drive hard disk brushless motors ,CD-ROM brushless motor and
so on ， the micro 3-wire or 4-wire without hall brushless motor ,
It's have reverse voltage protection , Over current protection , Phase inversion control
Driver voltage : DC5-12v
Working voltage : ≤1.2A
Speed adjust :0%-100%
Note : Brushless motor line of receiving terminal drive plate must be pressed
sturdiness, poor contact will lack of phase operation and burn out the chip.Board
terminals fixed screw clearance, please use coarser line connected to the board.
How to identify four line motor public port: use the resistance of the multimeter *
gears test this four terminal,One of the terminals and the other three terminal
resistance value of the minimum and equal
So it's COM terminal
Size:6*4.5cm/2.36"*1.77"
Quantity: 1Pc
Note:
Due to the difference between different monitors, the picture may not reflect  the
actual color of the item. Thank you!
10pcs Sound Module For Toy IC Chip Siren
Music Integration Module 3V Alarm Voice
Sound Chip Module Police Music for
DIY/Toy
Description:
 

1. working voltage:3V

 
 

 
Max 5A Adjustable CC CV Step Down
Receiver Charge Module Digital Voltmeter
Ammeter Display LED Driver for Arduino
Non-isolated
 Universal receiver.
 100% Brand New
 Module Properties: non-isolated constant current and voltage module
 Rectification: non-synchronous rectification
 Input voltage: 5V-32V
 Output voltage: 1.27V-30V
 Output current: adjustable maximum 5A
 Conversion efficiency: 95% (the highest)
 Switching frequency: 300KHz
 Output ripple: 50mV (max) 20M bandwidth
 Load Regulation: ± 0.5%
 Voltage Regulation: ± 2.5%
 Operating Temperature: -40°to +85°
 Size: 51 * 26.3 * 14 (L * W * H) (mm)

Voltmeter Ammeter

 Measurement accuracy: 0.1%

 Refresh rate: about 200ms / times\
 Display: 0.28"digital tube
 Current Range 0A-5A
 Voltage range 5V-30V
 Display Color Red

Package Included:

 100% Brand New

 DC 5A 0.8V-30V Constant Current/Voltage LED Driver Step-Down Power
Module  x

 
 

 
 

 
 

Multifunction Delay Trigger ChipTiming

Mudule Timer IC Timing 2s -1000h
Specifications:

Shape about 12mm * 12mm, operating voltage 2v-5v,timing can be set to a minimum to a
maximum of 2 seconds 1,000 hours, as indicated below description

Function and Design

1. The circuit according to claim connected and set a good time resistance
and supply voltage;
2. Before the power not trigger output is high;
3. Trigger terminal "falling" trigger effective immediately
after the trigger output terminal goes low at the same time start the timer
circuit;
4. Set the timer time to recover after the output terminal is high, wait for
the next "falling" trigger;
5. The chip is not repeated triggered, meaning that
continue to trigger in the period after the trigger chip output low if the
trigger is invalid;
6. The trigger end of "falling" Trigger refers to the instantaneous change
from high level to a low level;
7. General refers to VCC high voltage, low means 0-0.3v or GND,
provided that they meet the level requirements can be;
8. trigger terminal can be connected to touch switch or microcontroller IO
port or
other digital circuits have a "falling" can effectively trigger;
9. The trigger can be designed to power, only to trigger a short circuit to
ground, power is triggered,
the time to recover after the output to a high level, waiting for the next
Falling edge trigger again.
 

Chip Features:

1. The use of low-power CMOS technology, lead-free and environmentally

friendly.
2. Direct Push can output low LED
(please add current limiting resistor), the output high may push transistor
(please add current limiting resistor).
3. Available resistance adjusting timing, there are 8 * N (N = 0.1.2.3) times
the timing selection,

time can be adjusted from 2s-1000h.

4. Optional trigger timing and triggering termination ground electric timer.
5. standby output high, falling edge trigger, post-trigger output low, after
the delay recovery high.

Pluggable Development Bare Board For

ATtiny13A ATtiny25 ATtiny45 ATtiny85
Programming Editor Micro Usb Power
Connector Module
 1PCS * Development Programmer Board for
ATtiny13A/ATtiny25/ATtiny85/ATtiny45

 
ATTinyCore, HW-260 and the ATTINY85
By grovedc in CircuitsArduino

1,021

Introduction: ATTinyCore, HW-260 and the ATTINY85

The ATtiny85 is one of my favorite programmable devices. In this 8 pin device, you get 512
bytes of RAM memory, 8K bytes of ROM memory, EEPROM and so much more. It is very
inexpensive, and is also a great place to get started with Arduino.

I was recently asked by a friend to help her get started. This can be a bit confusing, particularly
considering the number of options available. Also, the state of play has been moving a lot lately
and while many older tutorials are still current, others are not.

I'd like to go through getting started with the HW-260 board. I had not seen this before, and I
found it to be very interesting. Before that, though, let's look at the other boards very quickly.
The ATTINY85 board has been been around for some time now. For about $2 you get the
ATtiny85, a USB connector, and a 5 volt voltage regulator. An LED is connected on pin 1. With
the voltage regulator, you can connect an external power source and have the voltage regulated
down to 5 volts. The ATTINY85 requires a bootloader to function. The bootloader will watch
the USB port when first powered on. This allows the device to be programmed. If no USB
activity is detected, then the bootloader will hand off to the user code. I am using Micronucleus
version 2.5, and this version leaves 6586 bytes available for the user code. Note that most
ATTINY85 boards come preinstalled with an older version of Micronucleus, usually 1.6 or 1.2,
and you can use ATTinyCore to update the bootloader.

The red board is the Sparkfun Tiny Programmer. There are many ISP programmers available. I
have found this programmer to be very reliable, and I recommend it. I will be using this board in
this tutorial to program the ATtiny85.

The HW-260 board is available on AliExpress for 45 cents US. The listing calls the board:

Pluggable ATTINY Development Board For ATtiny13A/ATtiny25/ATtiny45/ATtiny85

Programming Editor Micro Usb Power Connector

As mentioned, I had never heard of this board before. So what exactly is this board? I couldn't
see how it could be used as a programmer. It would need a processor on the board to be an ISP.
You can't just plug in a Tiny85 and program it. So I uploaded a blink sketch to a Tiny85 using
the Sparkfun Tiny Programmer. This worked just fine, with the LED being on pin 1. So this got
me thinking, can I actually load a bootloader on to a bare Tiny85 and put it on the HW-260. As it
turns out, yes you can. Effectively, the HW-260 is the same as an ATTINY85, but with a socket
for a ATtiny85. This means that you can use the HW-260 just like a ATTINY85, or you can have
no bootloader at all and have all 8K of ROM available. The HW-260 actually be programmed
and used as an ISP.

This can all be done using just the ATTinyCore board in the Arduino IDE.

Supplies
You will need the Arduino IDE installed, as well as:

 An an ISP programmer. I am using the Sparkfun Tiny Programmer.

 A HW-260 board
 One or more ATtiny85 chips

Step 1: Configure the Arduino IDE

Providing support for the attinycore is done by installing the boards manager URL on the
preferences page, and then installing the board in the boards manager. This can be done as
described on the projects Home Page.

Note as well that on the preferences page, there are two buttons next to, "Show verbose output
during:". Enabling these two options show a lot of very good information for the process
described below.

You can check the installation in the boards manager as shown in the image above.

Step 2: Programming the ATtiny85 With the ISP

Place your ATtiny85 chip into the Sparkfun Tiny Programmer. Take care to get the notch on the
chip aligned with the notch in the center of the socket on the ISP. The ATtiny85 is shipped with
the clock set to 1 mHz. The first step will be change the clock to 8 mHz.

This is shown in the first image above. Note that the programmer is set to "for new or 1 mHz
parts".

Go ahead and hit the "Burn Bootloader" button at the end of the list. Note that we aren't actually
burning a bootloader yet. If you have the verbose logging enabled, you can see that the file that is
loaded is:

.arduino15/packages/ATTinyCore/hardware/avr/1.5.2/bootloaders/empty/empty_all.hex

Or, an empty bootloader. But the ATtiny85 is now configured for 8mHz internal clock.
Step 3: Burn the Initial Bootloader

Now, with the ATtiny85 chip still in the Sparkfun Tiny Programmer ISP, configure the board as
shown above. Note that the board is: ATtiny85 (micronuclues DigiSpark). The Clock is 8 mHz
(No USB). The Burn Bootloader Method is "Fresh Install (via ISP), and that the programmer is
the "USBtinyISP", but now for the faster parts.

This will install:

arduino15/packages/ATTinyCore/hardware/avr/1.5.2/bootloaders/micronucleus/
t85_entry_on_power_on_no_pullup_fast_exit_on_no_USB.hex 

on to the ATtiny85 chip.

I usually get an error at the end of this burn, but it does complete successfully.
Step 4: Burn the Final Bootloader

Now, take the ATtiny85 chip from the Sparkfun Tiny Programmer ISP and place it on the HW-
260. Once again watching the proper orientation of the notch.

Configure you board as shown above and burn the bootloader. This will install:

.arduino15/packages/ATTinyCore/hardware/avr/1.5.2/bootloaders/micronucleus/upgrade-
t85_entry_on_power_on_no_pullup_fast_exit_on_no_USB.hex 

With the clock set to 16.5 mHz on the ATtiny85.

You can now load your sketch to your HW-260 board with these same settings.
Promotion! LJ18A3-8-Z/BX 8mm Approach
Sensor NPN NO Switch DC 6-36V
It is a component widely used in automatic control industry for detecting, controlling, and
noncontact switching.
When proximity switch is close to some target object, it will send out control signal.
It's widely used in machine, paper making, light industry for limiting station, orientation
taking count, speeding trial ect.
LJ18A3-8-Z/BX 8mm Approach Sensor Inductive Proximity NPN NO Switch DC 6-36V
color:as picture show

 
Bios Board MX25L6405 W25Q64 USB
Programmer LCD Burner CH341A
Progammer for 24 25 Series
Check your parcel
in http://www.yw56.com.cn/english/index.aspx 
 

To all sorts of color TV set memory (24 series IC), LCD (24.25 series IC)  desktop
motherboard (25 series IC) notebook (25 series IC) router (25 series IC) card (25 series
IC) DVD (25 series IC), set-top boxes (25 series IC) software to unlock, backup,
erasing, burning, check.

24 and 25 series FLASH programmer

 
Summary:
24 and 25 series of FLASH has been very popular at present. Burn for these chips,
currently only professional programmer can support, but the price of a professional
programmer is very expensive, not general maintenance users can have; So we can
create a support block 24 series of EEPROM and ST, WINB IND, AMIC, MXIC, SST,
SPANSION, EON, PMC and other manufacturers of 8 feet 25 series chip programmer.
 
The programmer features:
1, by special USB chip CH341A production. USB1.1 communication. Burning speed
than ordinary ATMEGA8 25
Series of programming 2-3 times faster. Erase the burning check speed about 2-3 mbit
per minute. Very suitable for amateur burning
24 and 25 series of FLASH.
2, support WIN98, WINME, WIN2K, WINXP, VISTA, Windows 7 - a 32-bit operating
system.
3, USES the USB port power supply
2: put the programmer computer USB port, open the "CH341A programmer software"
the burning software. Choose good chip capacity, can burn write and erase the chips.
Download online (USB serial port, P/S end cap off)
Put the programmer computer USB port, programmer received nine RX, TX foot on the
TX and RX received notice from nine GND received nine GND.
Choose corresponding COM, open the corresponding download software platform,
online upgrade your nine machine. (software upgrade not programmer accompanying
the software)

Driver installation
1: install parallel port driver (burning 24 and 25 series used FLASH drive)
Will jump on the PCB P/S end cap closed
Detailed installation steps "CH341A parallel port driver and instructions in the
installation instructions - TB" folder
2: install serial port driver (such as USB serial port, in nine support serial model online
download online download)
Will jump on the PCB P/S end cap is removed
Detailed installation steps "CH341A serial port driver and instructions in the installation
instructions - TB" folder
24 series chip burning (P/S jump end cap closed)
: put the programmer computer USB port, open the USB port "24 to 25 series of burning
of the programmer"
Software. Choose good chip capacity, can burn. 25 series chip burning (P/S jump end
cap closed)
6. Read 25 x80 series 8 m chip only 9 seconds. 25 x80 erasures - blank check -
programming - a charm to complete the four steps only 1 minute, 6 seconds
 

 
 

 
Marked on our software on the chip and the programmer chip position is one-to-one, not
like others boast is licensed, the software on the chip position and marked on the
programmer chip placing position not corresponding, genuine and not the original you
can see at a glance.

Cara Menggunakan CH341A programmer

Terupdate 2022
March 14, 2022

CH341a – Untuk orang yang berprofesi di bidang elektronika tentunya sudah tidak asing dengan 
sebuah aplikasi bernama CH341A programmer. Karena peran aplikasi ini sangat penting dalam
pekerjaan sehari-hari seorang teknisi.

Meski begitu, banyak teknisi yang mengetahui namun tidak tau cara penggunaannya. CH341A
adalah sebuah aplikasi yang digunakan dalam proses pemrograman chip memori. Aplikasi ini
punya kemampuan untuk:

 Formatting chip memori

Intinya adalah flashing, dimana dengan aplikasi ini kita bisa menghapus data lama yang korup
dan menggantinya dengan yang baru.

 Untuk isi memori dengan data

Memasukan firmware atau data ke chip yang kosong untuk berbagai kebutuhan

 Mengambila data dari chip memori

Mengambil dan menulis ulang dari satu perangkat ke perangkat lain.

 Berguna untuk melakukan flash chip memori perangkat elektronik yang menggunakan chip
memori

pernah beli memori di toko? taukah kalian bahwa toko juga menjual chip yang sudah ada isinya?
iya sudah ada data firmware di dalamnya.

pasti kamu bingung kan, kok bisa chip baru sudah ada isinya?

iya, bisa ada isinya karena mereka memindahkan dengan aplikasi khusus untuk memindahkan
data yaitu CH341A.

Dan yang menarik lagi, untuk melakukanya tidak terlalu sulit. Siapapun pasti bisa!

Berikut ini adalah hal-hal yang perlu di persiapkan:

 Firmware-firmware yang akan di masukan

 Chipmemori yang sudah ada isinya
 Chip memori yang masih kosong
 Driver dan Software CH341A
 1 Perangkat CH341A bisa di dapat di toko online
 1 buah Komputer atau Laptop

Cara mengoperasikan CH341A programmer

Sebelum memulai pengoperasian CH341A progammer, pastikan drivernya sudah terinstal di
komputer. Kamu bisa mencari driver dan software untuk CH341A programmer di internet
dengan mudah.

Next, buka folder USB driver dan instal dengan cara klik kanan ,klik run as Administrator dan
pilih file CH341A.

Bila driver nya sudah terinstal, pasangkan CH341A programmer yang sudah di pasang chip
kosong ataupun yang terisi yang akan di flash ulang. Masukan ke USB port untuk
menyambungkannya.
Disini pastikan chip memori di terpasang dengan baik. Operasikan software CH341A tadi yang
sudah di download, cari folder CH341A_V1.29.

Cara Backup data firmware dari chip memori dengan CH341A programmer

Jika contohnya ingin backup data, maka chip memori yang dipasang harus yang sudah terisi. Jadi
begini panduannya:

Pilih  detect, untuk mengetahui apakah chiop memori terbaca dan tidak ada masalah dan sudah
terpasang baik. Berikut ini adalah beberapa informasi yang akan muncul:

 Manufacture(pembuat memori)
 Memory name(nama memori)
 Memory size(ukuran memori)
 Manufacture ID(kode memori)
 Memory Type(jenis memori)
 Memory Capacity(kapasitas penyimpanan memori)
 Device ID(ID perangkat CH341A)

Sebelumnya adalah proses pendeteksian Chip memori, jika sudah selesai artinya aman lalu klik
“read”. Dan tunggu pemrosesan hingga 100 persen.

Jika proses pembacaan firmware dalam chip sudah selesai, selanjutnya klik Save dan Simpan dan
jangan lupa untuk beri nama file firmware tersebut.

Maka proses backup data menggunakan CH341A programmer sudah selesai. Mudah bukan?
Tutorial selanjutnya adalah cara mengisi data firmware ke chip kosong.

Tutorial lengkap mengisi data ke chip memori kosong menggunakan CH341A programmer

Untuk yang ini pastikan chip yang di masukan adalah chip memori kosong karena kita akan
mengisi data firmware ke memori kosong ini.

Yang pasti harus di perhatikan penyimpanan memori harus lebih besar dari pada firmware Dan
inilah langkah-langkah mengisi data ke chip memori  kosong.

Sama seperti proses sebelumnya, Pada tampilan software CH341A programmer klik detect untuk
cek apakah chip bisa di baca dengan baik. Lalu pilih open dan buka file firmware yang akan di
masukan ke chip dan masukan ke software.

Setelah file firmware sudah di load, lalu kli write, artiya software akan melakukan penulisan data
ke chip memori yang kosong. Tunggu proses ini sampe selesai 100 persen.

Langkah terakhir hanya tinggal pilih Verify. Dan proses pengisian data ke chip memori kosong
pun selesai.
BACA JUGA : Skema Mic Condenser Buatan Sendiri Paling Mudah

Cara Flash ulang data firmware menggunakan  CH341A programmer

Proses ini dilakukan biasanya jika ada error pada Chip memori, penyebabnya bisa macam –
macam misalnya upgrade sistem yang tidak selesai atau gagal, atau juga bisa ada kesalahan saat
memasukan firmware pada perangkat.

Proses Flasing data firmware Menggunakan CH341A sangat mudah, sebelumnya pastikan kamu
punya firmware yang sesuai.

Dan inilah langkah-langkah Cara flash data firmware menggunakan CH341A.

Dari tampilan depan software  CH341A programmer, lagi seperti diawal klik detect untuk
membaca chip set nya sudah oke atau belum.

Jika ternyata misalkan chip memori sudah tidak terbaca karena eror yang parah maka flashing
tidak bisa dilakukan dan proses gagal.

Jika memori terbaca dan aman, klik tombol Erase untuk membuang data yang korup pada chip
tersebut dan tunggu sampai selesai.

Setelah penghapusan data korup selesai, langkah berikutnya adalah klik Open untuk memilih file
firmware yang sudah disiapkan untuk dimasukan.

Unggah file tersebut ke Software, dan ikuti instruksi selanjutnya hingga semua selesai. Jika
filenya sudah di Load, pilih Write dan tunggu sampai selesai 100 persen prosesnya.

Terakhir tinggal klik tombol verify , tunggu dan pastikan tidak ada eror sampai proses selesai.

Berikut adalah Tutorial menggunakan CH341A programmer, semoga infonya bermanfaat.

Kegunaan dari tombol-tombol pada aplikasi CH341A

 Nomor 1(membaca seri eeprom)

 Nomor 2(membuka file)
 Nomor 3(saving file)
 Nomor 4(membaca software)
 Nomor 5(unggah software)
 Nomor 6(menghapus software)
 Nomor 7(verifikasi data)