MHC-V71/V71D

2020/04/28 00:01:32 (GMT+09:00)

SERVICE MANUAL US Model

Canadian Model
Ver. 1.3 2020.04 MHC-V71

AEP Model
UK Model
E Model
Australian Model
MHC-V71D

Note:
Be sure to keep your PC used for service and
checking of this unit always updated with the
latest version of your anti-virus software.
In case a virus affected unit was found during
service, contact your Service Headquarters.
Photo: MHC-V71D

Model Name Using Similar Mechanism MHC-V77W/V77DW

CD/DVD
VSSAMARA09 - 7/18/2022 5:25 AM
Section
CD/DVD Mechanism Type
Optical Pick-up Name
CDM90-DVBU204//M
CMS-S76RFS7G1 OR CMS-S76RFS7GP

SPECIFICATIONS
AUDIO POWER SPECIFICATIONS HDMI OUT (TV) ARC (V71D): 87.5 MHz – 108.0 MHz (50 kHz NFC section (V71D)
Supported audio signal: step) (V71D) Operating frequency:
POWER OUTPUT AND TOTAL HARMONIC
2-channel Linear PCM (up to 13.56 MHz
DISTORTION: BLUETOOTH section
48 kHz), Dolby Digital
(US models only) Communication system: Supported audio formats
With 4 ohm loads, both channels driven, from HDMI section (V71D) BLUETOOTH Standard version 4.2 Supported bit rate and sampling frequencies:
400 Hz – 20,000 Hz; rated 60 watts per channel Connector: Output: MP3:
minimum RMS power, with no more than 0.7% Type A (19 pin) BLUETOOTH Standard Power Class 2 32/44.1/48 kHz, 32 kbps –
total harmonic distortion from 250 milliwatts to Disc player section Maximum output power (V71D): 320 kbps (VBR)
rated output. System: < 9.5 dBm AAC:
Compact disc and digital audio Maximum number of devices to be registered: 44.1 kHz, 48 kbps – 320 kbps
Speaker section
system (V71) 8 devices (CBR/VBR)
Speaker system:
Maximum number of simultaneous connection WMA:
3-way, Double Bass Reflex Compact disc and digital audio
and video system (V71D) (Multipoint): 44.1 kHz, 48 kbps – 192 kbps
Speaker unit:
Laser Diode Properties 3 devices (CBR/VBR)
Tweeter L/R: 50 mm (2 in), cone type
Emission Duration: Continuous Maximum communication range: WAV:
Midrange L/R: 120 mm (4 3/4 in), cone type
Laser Output*: Less than 44.6 μW Line of sight approx. 10 m (33 ft) *1 44.1/48 kHz (16 bit)
Woofer: 300 mm(11 7/8 in), cone type
* This output is the value measurement Frequency band: Supported video formats (V71D)
Inputs 2.4 GHz band (2.4000 GHz –
at a distance of 200 mm from the Xvid:
AUDIO/PARTY CHAIN IN L/R (V71): 2.4835 GHz)
objective lens surface on the Optical Video codec: Xvid video
Voltage 2 V, impedance Modulation method:
Pick-up Block with 7 mm aperture. Bit rate: 4.854 Mbps (MAX)
24 kilohms FHSS (Freq Hopping Spread Spectrum)
Frequency response: Resolution/Frame rate:
AUDIO/PARTY CHAIN IN (TV) L/R (V71D): Compatible BLUETOOTH profiles *2:
20 Hz – 20 kHz 720 × 480, 30 fps
Voltage 2 V, impedance A2DP (Advanced Audio Distribution
Video color system format (V71D): 720 × 576, 25 fps (except for Latin
24 kilohms Profile)
Latin American model: American model)
TV (ARC) (V71D): AVRCP (Audio Video Remote
NTSC Audio codec: MP3
Supported audio signal: Control Profile)
Other models: MPEG4:
2-channel Linear PCM SPP (Serial Port Profile)
NTSC and PAL File format: MP4 File Format
MIC1: HFP (Hands-free Profile)
USB section Video codec: MPEG4 Simple
Sensitivity 1 mV, impedance HSP (Headset Profile)
Supported USB device: Profile (AVC is not compatible.)
10 kilohms Supported codecs:
Mass Storage Class Bit rate: 4 Mbps
MIC2/GUITAR: SBC (Subband Codec)
Maximum current: Resolution/Frame rate:
Sensitivity 1 mV, impedance AAC (Advanced Audio Coding)
1A 720 × 480, 30 fps
10 kilohms (When guitar mode is LDAC
(USB) port: 720 × 576, 25 fps (except for Latin
turned off.) *1
Type A The actual range will vary depending on American model)
Sensitivity 200 mV, impedance
factors such as obstacles between devices, Audio codec: AAC-LC (HE-AAC is
250 kilohms (When guitar mode is FM tuner section magnetic fields around a microwave oven, not compatible.)
turned on.) FM stereo, FM superheterodyne tuner static electricity, reception sensitivity, DRM: Not compatible
Outputs Antenna: antenna’s performance, operating system,
AUDIO/PARTY CHAIN OUT L/R: FM lead antenna software application, etc.
Voltage 2 V, impedance 1 kilohm Tuning range: *2
BLUETOOTH standard profiles
VIDEO OUT (V71D): 87.5 MHz – 108.0 MHz (100 kHz – Continued on next page –
indicate the purpose of BLUETOOTH
Max. output level 1 Vp-p, step) (V71)

HOME AUDIO SYSTEM

communication between devices.
unbalanced, Sync. negative load
impedance 75 ohms

9-890-695-04
2020D81-1 Sony Corporation
© 2020.04 Published by Sony EMCS (Malaysia) PG Tec

SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.3

General • A  pple, the Apple logo, iPhone, iPod,

iPod touch, and Siri are trademarks of
NOTES ON CHIP COMPONENT REPLACEMENT
Power requirements:
US, CND models: Apple Inc., registered in the U.S. and • Never reuse a disconnected chip component.
other countries. App Store is a service
AC 120 V, 60 Hz mark of Apple Inc., registered in the U.S. • Notice that the minus side of a tantalum capacitor may be dam-
Except US, CND models:
AC 120 V – 240 V, 50/60 Hz
and other countries.
• U se of the Made for Apple badge means
aged by heat.
Power consumption: that an accessory has been designed
120 W to connect specifically to the Apple FLEXIBLE CIRCUIT BOARD REPAIRING
product(s) identified in the badge, and
Power consumption (at the Power Saving
has been certified by the developer to • Keep the temperature of the soldering iron around 270 °C dur-
mode) (V71D):
0.5 W (When “BT STBY” is set to
meet Apple performance standards. Apple ing repairing.
is not responsible for the operation of this
“OFF” and [CONTROL FOR device or its compliance with safety and • Do not touch the soldering iron on the same conductor of the
HDMI] is set to [OFF].) regulatory standards.
2 W* (When “BT STBY” is set to • THIS PRODUCT IS LICENSED UNDER
circuit board (within 3 times).
“ON” and [CONTROL FOR HDMI] THE MPEG-4 VISUAL PATENT • Be careful not to apply force on the conductor when soldering
PORTFOLIO LICENSE FOR THE
is set to [ON].)
PERSONAL AND NON-COMMERCIAL or unsoldering.
Dimensions (W/H/D) (Approx.):
USE OF A CONSUMER FOR
370 mm × 930 mm × 427 mm
(14 5/8 in x 36 5/8 in x 16 7/8 in)
(i) ENCODING VIDEO IN COMPLIANCE SAFETY CHECK-OUT
WITH THE MPEG-4 VISUAL STAN-
Mass (Approx.): DARD (“MPEG-4 VIDEO”) After correcting the original service problem, perform the following
22 kg (48 lb 9 oz) AND/OR safety check before releasing the set to the customer:
Operating temperature: (ii) DECODING MPEG-4 VIDEO THAT
5 °C to 35 °C (41 °F to 95 °F) WAS ENCODED BY A CONSUMER Check the antenna terminals, metal trim, “metallized” knobs,
* T he power consumption of the system ENGAGED IN A PERSONAL AND
NON-COMMERCIAL ACTIVITY AND/
screws, and all other exposed metal parts for AC leakage. Check
will be less than 0.5 W when there is no
HDMI connection and “BT STBY” is set OR WAS OBTAINED FROM A VIDEO leakage as described below.
to “OFF”. PROVIDER LICENSED TO PROVIDE
MPEG-4 VIDEO.
Unpacking NO LICENSE IS GRANTED OR SHALL
LEAKAGE TEST
• This unit (MHC-V71/V71D) (1) BE IMPLIED FOR ANY OTHER USE. AD- The AC leakage from any exposed metal part to earth ground and
DITIONAL INFORMATION INCLUDING
• R emote control (1)
THAT RELATING TO PROMOTIONAL, from all exposed metal parts to any exposed metal part having a
• R 03 (size AAA) batteries (2)
• F M lead antenna (1)
INTERNAL AND COMMERCIAL USES
AND LICENSING MAY BE OBTAINED
return to chassis, must not exceed 0.5 mA (500 microamperes).
• A C power cord (mains lead) (1) FROM MPEG LA, L.L.C. Leakage current can be measured by any one of three methods.
• A C plug adaptor* (1) (supplied only for HTTP://WWW.MPEGLA.COM
certain areas) (V71D) • A ll other trademarks are trademarks of
1. A commercial leakage tester, such as the Simpson 229 or RCA
* This plug adaptor is not for the use in their respective owners. WT-540A. Follow the manufacturers’ instructions to use these
Chile, Paraguay and Uruguay. Use this • I n this manual, ™ and ® marks are not
plug adaptor in the countries where it is specified. instruments.
necessary. 2. A battery-operated AC milliammeter. The Data Precision 245
Design and specifications are subject to
change without notice.
digital multimeter is suitable for this job.
License and Trademark Notice
3. Measuring the voltage drop across a resistor by means of a
•  is a trademark of DVD Format/Logo VOM or battery-operated AC voltmeter. The “limit” indication
Licensing Corporation. is 0.75 V, so analog meters must have an accurate low-voltage
• “DVD+RW”, “DVD-RW”, “DVD+R”,
“DVD-R”, “DVD VIDEO”, and the “CD” scale. The Simpson 250 and Sanwa SH-63Trd are examples
logos are trademarks. of a passive VOM that is suitable. Nearly all battery operated
• WALKMAN ® and WALKMAN ® logo are
registered trademarks of Sony Corpora- digital multimeters that have a 2V AC range are suitable. (See
tion.
• MPEG Layer-3 audio coding technology and
Fig. A)
patents licensed from Fraunhofer IIS and
Thomson.
• Windows Media is either a registered To Exposed Metal
trademark or trademark of Microsoft Parts on Set
Corporation in the United States and/or other
countries.
• This product is protected by certain
intellectual property rights of Microsoft
Corporation. Use or distribution of such
technology outside of this product is
prohibited without a license from Microsoft
or an authorized Microsoft subsidiary.
• This system incorporates Dolby* Digital.
* Manufactured under license from Dolby AC
Laboratories. Dolby, Dolby Audio, and the
double-D symbol are trademarks of Dolby 0.15 µF 1.5 kΩ voltmeter
Laboratories. (0.75 V)
• T his system incorporates High-
Definition Multimedia Interface
(HDMI™) technology. The terms HDMI
and HDMI High-Definition Multimedia
Interface, and the HDMI Logo are
trademarks or registered trademarks of
HDMI Licensing Administrator, Inc. in
the United States and other countries.
• “ BRAVIA” is a trademark of Sony
Earth Ground
Corporation.
• L DAC™ and LDAC logo are trademarks Fig. A. Using an AC voltmeter to check AC leakage.
of Sony Corporation.
• T he BLUETOOTH ® word mark and
logos are registered trademarks owned SAFETY-RELATED COMPONENT WARNING!
by Bluetooth SIG, Inc. and any use
of such marks by Sony Corporation is
under license. Other trademarks and
trade names are those of their respective COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
owners. WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
• The N-Mark is a trademark or registered
trademark of NFC Forum, Inc. in the United THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
States and in other countries. REPLACE THESE COMPONENTS WITH SONY PARTS
• A ndroid, Google Play, and the Google
Play logo are trademarks of Google LLC. WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR

LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC-
TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE
PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON-
NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.

2
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.2

TABLE OF CONTENTS

1. SERVICING NOTES .............................................. 4 6-11. Printed Wiring Board

- SMPS Board (EA, BR, AR, LA9, E12),
2. DISASSEMBLY SMPS (EMC) Board
2-1. Disassembly Flow............................................................ 9 (US, CND, AEP, UK, RU, MY, AUS, E4) -.................... 44
2-2. Side Panel L, R................................................................ 10 6-12. Printed Wiring Board -
2-3. Loading Panel Assy......................................................... 11 HUB Board
2-4. Top Panel (Vanilla) Section............................................. 12 (US, CND, AEP, UK, RU, MY, AUS, E4),
2-5. Rear Cover, Ventilation Cover......................................... 13 HUB //NON-EMC Board (EA, BR, AR, LA9, E12) -..... 45
2-6. Back Panel Section.......................................................... 14 6-13. Printed Wiring Board - MIC USB Board -...................... 46
2-7. CDM Section................................................................... 15 6-14. Printed Wiring Board - VFD Board -............................... 46
2-8. Service, Optical Device (7G), Flexible Flat Cable.......... 16 6-15. Printed Wiring Board - 360 BACK L Board -................. 47
2-9. MOTHERBOARD Board................................................ 17 6-16. Printed Wiring Board - 360 BACK R Board -................. 47
2-10. SMPS Board, Chassis Section......................................... 18 6-17. Printed Wiring Board - 360 FR L Board -....................... 48
2-11. Front Panel (Vanilla) Section........................................... 19 6-18. Printed Wiring Board - 360 FR R Board -....................... 48
2-12. Loudspeaker 30cm (Woofer) (SP5)................................. 20 6-19. Printed Wiring Board - POWER KEY Board -............... 49
2-13. Loudspeaker (12cm) (Mid: L-CH) (SP1), 6-20. Printed Wiring Board - EXTENSION Board -................ 49
Loudspeaker (12cm) (Mid: R-CH) (SP3)........................ 21 6-21. Printed Wiring Board - NFC Board -............................... 49
2-14. Bottom Cover Section...................................................... 22 6-22. Printed Wiring Board - IR Board -................................... 49
6-23. Printed Wiring Board - SPK MID L Board -................... 50
3. TEST MODE ............................................................. 23 6-24. Printed Wiring Board - SPK MID R Board -................... 50
6-25. Printed Wiring Board - SW LED L Board -..................... 50
4. ELECTRICAL CHECK .......................................... 24 6-26. Printed Wiring Board - SW LED R Board -.................... 50

5. TROUBLESHOOTING ........................................... 25 7. EXPLODED VIEWS

7-1. Side Panel Section........................................................... 51
6. DIAGRAMS 7-2. Loading Panel, Rear Cover Section................................. 52
6-1. Block Diagram - MAIN Section (1/2) -........................... 33 7-3. Back Panel Section.......................................................... 53
6-2. Block Diagram - MAIN Section (2/2) -........................... 34 7-4. MOTHERBOARD Board Section................................... 54
6-3. Block Diagram - AMP Section -...................................... 35 7-5. SMPS Board, Chassis Section......................................... 55
6-4. Block Diagram - CD/DVD, USB, HDMI Section -........ 36 7-6. Front Panel Section.......................................................... 56
6-5. Block Diagram - TOUCH, LED DRIVER Section -....... 37 7-7. Bottom Cover Section...................................................... 57
6-6. Block Diagram 7-8. Speaker Cabinet Section.................................................. 58
- PANEL, POWER SUPPLY Section (1/2) -................... 38 7-9. Top Panel Section............................................................ 59
6-7. Block Diagram 7-10. CDM Section................................................................... 60
- PANEL, POWER SUPPLY Section (2/2) -................... 39 7-11. CD/DVD Mechanism Section
6-8. Printed Wiring Board - MOTHERBOARD Board -........ 41 (CDM90-DVBU204//M)................................................. 61
6-9. Printed Wiring Board
- SENSOR Board (Component Side) -............................ 42 8. ELECTRICAL PARTS LIST ............................... 62
6-10. Printed Wiring Board
- SENSOR Board (Conductor Side) -.............................. 43 Accessories are listed in the last part of the electrical parts list.

VSSAMARA09 - 7/18/2022 5:25 AM

3
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.3 SECTION 1
SERVICING NOTES
UNLEADED SOLDER PLAYABLE DISCS
Boards requiring use of unleaded solder are printed with the • DVD VIDEO
leadfree mark (LF) indicating the solder contains no lead. • DVD-R/DVD-RW in DVD VIDEO format or video mode
(Caution: Some printed circuit boards may not come printed with • DVD+R/DVD+RW in DVD VIDEO format
the lead free mark due to their particular size) • VIDEO CD (Ver. 1.0, 1.1, and 2.0 discs)
• Super VCD
: LEAD FREE MARK • CD-R/CD-RW/CD-ROM in VIDEO CD format or super VCD
Unleaded solder has the following characteristics. format
• Unleaded solder melts at a temperature about 40 °C higher • AUDIO CD
than ordinary solder. • CD-R/CD-RW in AUDIO CD format
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time. PLAYABLE FILES ON DISCS
Soldering irons using a temperature regulator should be set to • Music:
about 350 °C. MP3 files (.mp3)*1*2
Caution: The printed pattern (copper foil) may peel away if • Video:
the heated tip is applied for too long, so be careful! MPEG4 files (.mp4/.m4v)*2*3, Xvid files (.avi)
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) PLAYABLE FILES ON USB DEVICE
than ordinary solder so use caution not to let solder bridges • Music:
occur such as on IC pins, etc. MP3 files (.mp3)*1*2, WMA files (.wma)*2, AAC files (.m4a/
• Usable with ordinary solder .mp4/.3gp)*2, WAV files (.wav)*2
It is best to use only unleaded solder but unleaded solder may • Video:
also be added to ordinary solder. MPEG4 files (.mp4/.m4v)*2*3, Xvid files (.avi)

*1
MP3 (MPEG 1 Audio Layer 3) is a standard format defined
CAUTION
Use of controls or adjustments or performance of procedures by ISO/MPEG for compressed audio data. MP3 files must be
other than those specified herein may result in hazardous radiation in MPEG 1 Audio Layer 3 format.
exposure.
*2
Files with copyright protection (Digital Rights Management)
cannot be played back by the system.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
*3
MPEG4 files must be recorded in MP4 file format. Supported
OR BASE UNIT video codec and audio codec are as follows:
– Video codec: MPEG4 Simple Profile (AVC is not sup-
ported.)
The laser diode in the optical pick-up block may suffer electrostatic
– Audio codec: AAC-LC (HE-AAC is not supported.)
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
Notes
During repair, pay attention to electrostatic break-down and also
• JIG
use the procedure in the printed matter which is included in the
When disassembling the set, use the following jig (for front
repair parts.
panel removal).
The flexible board is easily damaged and should be handled with
Part No.: J-2501-238-A JIG FOR SPEAKER REMOVAL
care.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.

For customers in AEP, UK

This appliance is classified as a

CLASS 1 LASER product under
IEC 60825-1:2007. This marking
is located on the rear exterior.
For customers in EA

This appliance is classified as a

CLASS 1 LASER product under
IEC 60825-1:2007 and IEC
60825-1:2014. This marking is
located on the rear exterior.
4
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.2

MODEL IDENTIFICATION

– Rear View –

MODEL NUMBER LABEL

US, CND E4, E12, AUS

R MODEL NO. : MHC-V71 R MODEL NO. : MHC-V71D

4-729-109-11 E4/E12
4-729-110-12 CEL/CEK

Destination Code Destination Code

PART No. PART No.
AEP, UK BR
R MODEL NO. : MHC-V71D
R MODEL NO. : MHC-V71D

4-729-110-12 CEL/CEK

Destination Code

VSSAMARA09 - 7/18/2022 5:25 AM

4-735-269-02 BR1
PART No.
RU, AR, EA, LA9, MY Destination Code
R MODEL NO. / MODELO : MHC-V71D PART No.

4-729-115-12 LA9

Destination Code
PART No.

Model Part No. DESTINATION ABBREVIATIONS

V71D: AR 4-729-108-1[] The following abbreviations for model destinations are used in this
service manual.
V71D: E4 4-729-109-1[]
V71D: E12 4-729-109-3[] • Abbreviation
V71D: AEP, UK 4-729-110-1[] AR : Argentina model
AUS : Australian model
V71: US, CND 4-729-111-1[] BR : Brazillian model
V71D: EA 4-729-112-1[] CND : Canadian model
V71D: MY 4-729-113-1[] E4 : African model
E12 : 220-240 V AC area in E model
V71D: LA9 4-729-115-1[]
EA : Saudi Arabia model
V71D: RU 4-729-116-1[] LA9 : Latin-American model
V71D: AUS 4-729-117-0[] MY : Malaysia model
RU : Russian model
V71D: BR 4-735-269-0[]
Note: Refer to supplement-1 for adding servicing notes
“DESTINATION SETTING METHOD” when the
complete MOTHERBOARD board is replaced.
5
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.2

Note: Refer supplement-2 for adding schematic diagram Protect Type Description:
of SMPS and SMPS (EMC) boards. X (Error Code) Description
2 Defect of thermistor IC or charging circuit
NOTE OF REPLACEMENT OF THE SENSOR BOARD used by SPM (Sound Pressure Management)
When the SENSOR board is defective, exchange the SERVICE, system.
TOP PANEL ASSY. 3 Power supply over current.
or
NOTE OF REPLACEMENT OF THE MS-476 BOARD DC appears in SP terminal by defect of AMP
When the MS-476 board is defective, exchange the entire IC.
LOADING COMPLETE ASSY (T). or
Unusual heat up of AMP IC by improper as-
TEST DISCS sembly of heat sink.
Use following TEST DISC when this unit confirms the operation 6 Defect of DC FAN and DC FAN driver circuit.
and checks it.
NOTE OF REPLACING THE IC2002 ON THE MOTH-
• For CD ERBOARD BOARD AND THE COMPLETE MOTHER-
Part No. Description BOARD BOARD
3-702-101-01 DISC (YEDS-18), TEST When IC2002 on the MOTHERBOARD board and the complete
4-225-203-01 DISC (PATD-012), TEST MOTHERBOARD board are replaced, it is necessary to spread the
J-2501-307-A DISC (HLX-A1), TEST compound between parts and heat sink.
After that, execute “3. IC and MOTHERBOARD board after re-
• For DVD SL (Single Layer) pair checking guide” (page 31).
Part No. Description
J-6090-069-A DISC (HLX-503), TEST (NTSC) Part No. Description
J-6090-088-A DISC (HLX-504), TEST (NTSC) 7-300-009-67 THERMAL COMPOUND (TIG2000)
J-2501-305-A DISC (HLX-513), TEST (NTSC) Spread the compound referring to the figure below.
J-6090-077-A DISC (HLX-506), TEST (PAL)
– MOTHERBOARD Board (Component Side) –
• For DVD DL (Double Layer)
Part No. Description
J-6090-071-A DISC (HLX-501), TEST (NTSC)
J-6090-089-A DISC (HLX-505), TEST (NTSC)
J-2501-306-A DISC (HLX-514), TEST (NTSC)
J-6090-078-A DISC (HLX-507), TEST (PAL)

RELEASING THE DISC TRAY LOCK

The disc tray lock function for the antitheft of sample disc in the
shop is equipped.
It can release the lock function in the following procedure.

Releasing Procedure:
1. Press the [1] button to turn the power on.
2. Touch the [FUNCTION] touch key to turn the DVD/CD func-
tion.
3. Touch [MEGA BASS] and [VOCAL FADER] touch keys
simultaneously for three seconds.
4. The message “UNLOCKED” is displayed on the screen thermal compound (TIG2000)
display panel and the disc tray is unlocked.
Note: When “LOCKED” is displayed on the screen display panel, the
disc tray lock is not released by turning the power on/off with the IC2002
[1] button.

IF “PROTECTX” (X IS A NUMBER)
AND “CHECK MANUAL” FLASHES
ON THE DISPLAY
Immediately unplug the AC
power cord (mains lead), and
check if anything is blocking the
ventilation openings of the unit.
After you have checked and
found no problems, reconnect
the AC power cord (mains lead),
and turn on the system. If the
issue persists, contact your
nearest Sony dealer.

6
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF

Note 1: After the side panel L, R are removed, this work is done.
Note 2: Please prepare the thin wire (clip etc. processed to the length of 8 cm or more).

1 Remove side panel L, R.

(Illustration of disassembly is omitted.)

hole

– Left view –

CD/DVD
3
mechanism deck
Insert the clip etc. processed to the
length of 8 cm or more in the hole
on the side of the CDM and push.

2 Insert the clip etc.

8 cm or more

tray
VSSAMARA09 - 7/18/2022 5:25 AM
Note: Push after it inserts it
in this hole well.
– Top view –

7
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

CAPACITOR DISCHARGE FOR ELECTRIC SHOCK PREVENTION

SMPS Board (Conductor side view)

In checking the SMPS board, make 4 capacitors discharge of C6301, C6322, C6505 and C6506 for eletrical shock prevention.

800 Ω/5 W 800 Ω/5 W 800 Ω/5 W

R R R

C6301
C6322
C6506

C6505

800 Ω/5 W

SERVICE POSITION

VFD board

POWER KEY board

panel, top (vanilla) section

MIC USB board

CDM90-DVBU204//M

stand

SMPS board

NFC board

8
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
SECTION 2 Ver. 1.2
DISASSEMBLY
Note: Disassemble the unit in the order as shown below.

2-1. DISASSEMBLY FLOW

SET

2-2. SIDE PANEL L, R 2-14. BOTTOM COVER SECTION

(Page 10) (Page 22)

2-3. LOADING PANEL ASSY

(Page 11)

2-4. TOP PANEL (VANILLA) SECTION

(Page 12)

2-5. REAR COVER,

VENTILATION COVER
(Page 13)

2-6. BACK PANEL SECTION

(Page 14)

2-7. CDM SECTION

(Page 15 )

2-8. SERVICE, OPTICAL DEVICE (7G), 2-9. MOTHERBOARD BOARD

FLEXIBLE FLAT CABLE (Page 17)
(Page 16)

2-10. SMPS BOARD, CHASSIS

SECTION
(Page 18)

2-11. FRONT PANEL (VANILLA)

VSSAMARA09 - 7/18/2022 5:25 AM SECTION

(Page 19)

2-12. LOUDSPEAKER 30CM 2-13. LOUDSPEAKER (12CM)

(WOOFER) (SP5) (MID: L-CH) (SP1),
(Page 20) LOUDSPEAKER (12CM)
(MID: R-CH) (SP3)
(Page 21)

9
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

Note: Follow the disassembly procedure in the numerical order given.

2-2. SIDE PANEL L, R

1 three screws
(tapping (flat head))

2 two screws
3 boss
(tapping (flat head))

3 boss

5 panel, side L

5 panel, side R
4 Remove the panel, side L 1 three screws
in the direction of the arrow. (tapping (flat head))

3 boss
3 boss

2 two screws
(tapping (flat head))

4 Remove the panel, side R

in the direction of the arrow.

10
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

2-3. LOADING PANEL ASSY

3 three claws

hole 4 panel, loading

assy

VSSAMARA09 - 7/18/2022 5:25 AM

– Left view –

CD/DVD mechanism
Insert the clip etc. processed to the deck 2 Draw out the tray.
1 Insert the clip etc.
length of 8 cm or more in the hole
on the side of the CDM and push.

8 cm or more

tray

Note: Push after it inserts it

in this hole well.
– Top view –

11
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

2-4. TOP PANEL (VANILLA) SECTION

qs Remove the panel, top (vanilla) section

in the direction of the arrow.
qd panel, top (vanilla) section
• Wire setting
top side
filament tape

4 flexible flat cable 2 one screw

(7 core) (CN120) (+BVTP 3 x 8)
3 flexible flat cable
(29 core) (CN126) 9 flexible flat cable
(9 core) (CN902)
flexible flat cable flexible flat cable 8 cushion (7T25), saranet
(7 core) (CN120) (29 core) (CN126) q; CN451 (5P)
qa three screws
(tapping
• Wire setting (flat head))
top side

filament
tape
1 two screws 6 flexible flat cable
hook (tapping (17 core) (CN5001)
(flat head))
bracket, CDM
5 filament tape
flexible flat cable
(17 core)
(CN5001)
7 Draw out the flexible
cushion (7T25), flat cable from the
saranet
hook.
Note 1: Make sure
the flexible
flat cable
(17 core)
must not – Front view –
near to the
bluetooth
chassis bluetooth module module.

Note 3: When you install the connector, please install them correctly.
There is a possibility that this machine damages when not
correctly installing it.
Note 2: When installing the flexible flat cable, ensure that the
colored line is not slanted after insertion. OK NG NG
Insert is straight Insert is shallow Insert is incline
OK NG to the interior.
connector connector
Insert is straight to the interior. Insert is incline connector
flexible flat flexible flat
cable cable
colored line colored line
connector connector
connector connector connector

12
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

2-5. REAR COVER, VENTILATION COVER

5 three screws
(+BVTP 3 x 8)

VSSAMARA09 - 7/18/2022 5:25 AM

8 Remove the cover, ventilation

in the direction of the arrow.
6 cover, rear

3 one screw
(+BVTP 3 x 8)

2 cover, screw L

9 cover, ventilation
1 Insert the clip etc.

– Rear view –
7 four screws
(+BVTP 3 x 8)

3 one screw 4 three screws

(+BVTP 3 x 8) (4 x 13)(TR-184A)

2 cover, screw R

1 Insert the clip etc.

13
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

2-6. BACK PANEL SECTION

Note : When you install the connector, please install them correctly. • Wire setting
There is a possibility that this machine damages when not
panel, back section MOTHERBOARD board
correctly installing it.

OK NG NG
Insert is straight Insert is shallow Insert is incline
to the interior.
connector connector
connector

connector connector connector

rear side

7 claw

3 Flip the cover, jack in the

direction of arrow.

8 Remove the panel, back section

in the direction of the arrow.

6 one screw
(+BVTP 3 x 8)

2 two screws
(+BVTP 3 x 8)
7 claw 6 one screw
(+BVTP 3 x 8)
1 CN2021
(6P) (V71D)
5 one screw
– Rear view – 9 panel, back section (+B 3 x 6)
6 two screws 4 two screws
(+BVTP 3 x 8) (+BVTP 3 x 8)

14
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

2-7. CDM SECTION

8 four screws
Note 1: When installing the flexible flat cable, ensure that the
(+BVTP 3 x 8)
colored line is not slanted after insertion.

OK NG
Insert is straight to the interior. Insert is incline 9 CDM90-DVBU204//M
flexible flat flexible flat
cable cable
colored line colored line
connector connector 3 flexible flat cable
(5 core) (CN303)

• Wire setting 2 flexible flat cable

rear side (24 core) (CN302)
CDM section filament tape
1 CN402 (4P)
qa four screws
q; four screws (screw (S), float)
(step screw M2.6)
qd loading base
6 two screws
(+BVTP 3 x 12)

qs claw
4 filament tape
qs claw

MOTHERBOARD board VSSAMARA09 - 7/18/2022 5:25 AM

• Wire setting
rear side qs claw

hook qs claw

qf bracket, CDM

7 Remove the CDM

bracket, section in the direction
CDM of the arrow.

5 Remove the connector and

two flexible flat cables
from hook.

Note 2: When you install the connector, please install them correctly.
There is a possibility that this machine damages when not
correctly installing it.

OK NG NG
Insert is straight Insert is shallow Insert is incline
to the interior.
connector connector
connector

connector connector connector

– Rear view –

15
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

2-8. SERVICE, OPTICAL DEVICE (7G), FLEXIBLE FLAT CABLE

2 chuck holder assy (T)

1 six claws

qa insulator qh flexible flat cable qf filament tape

(5 core)
7 four insulator screws

qs service,
optical device (7G)

qa insulator
qa insulator
8 qj holder, FFC
0
6 belt
qk flexible flat cable
qg (24 core)
3 Insert the thin
wire (clip etc.).

9 connector

qd loading base assy loading assy (T)

4

5 tray – Bottom view –

• Installation of flexible flat cable (24 core) and flexible flat cable (5 core)
Note: This illustration sees the loading assy (T) from bottom side.
5 three claws

5 two claws
1 flexible flat cable (24 core)
loading assy (T)

6 holder, FFC
3 Through the hole
4

7 flexible flat cable

terminal face (24 core)

2 Through the hole

8 flexible flat cable

Under the guide (5 core)
(Fold area)

Under the guide

16
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

2-9. MOTHERBOARD BOARD

Note 1: When the complete MOTHERBOARD board
is replaced, be sure to refer to “DESTINATION
SETTING METHOD” on supplement-1.

4 two screws qk heat sink (MB-L) (VANILLA)

(+BVTP 3 x 8) Note 2: When installing the heat sink (MB-L) (VANILLA),
7 fan, DC spread the compound referring to
6 bracket, fan “NOTE OF REPLACING THE IC2002 ON THE
MOTHERBOARD BOARD AND THE
qg clamp (N) COMPLETE MOTHERBOARD BOARD”
qh MOTHERBOARD on servicing notes (page 6).
board qf six screws (+PWH 3 x 8 (SUMITITE))

1 CN2001 (2P) VSSAMARA09 - 7/18/2022 5:25 AM

5 two screws
• Wire setting
front side
9 Remove the wires from clamp (N).
(+BVTP 3 x 8)
qg clamp (N)

• Wire setting front

side
2 Draw out the wires from fan unit.
qj two screws
hooks fan, DC (+BVTP 3 x 8)

q; CN001 (10P)

MOTHERBOARD board chassis

chassis section

MOTHERBOARD board

qs CN3001 (2P)
qa CN2007 (8P)
• Wire setting front side
8 Remove the cushion (CZ) from chassis.
qd CN2206 (8P)
3 CN127 (3P)

Note 3 : When you install the connector, please install them correctly.
There is a possibility that this machine damages when not
correctly installing it.

OK NG NG
Insert is straight Insert is shallow Insert is incline
to the interior.
connector connector
connector

MOTHERBOARD SMPS board (EA, BR, AR,

board LA9, E12) / SMPS (EMC)
board (US, CND, AEP, UK,
RU, MY, AUS, E4) connector connector connector

17
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

2-10. SMPS BOARD, CHASSIS SECTION

Note : When you install the connector, please install them correctly.
There is a possibility that this machine damages when not
correctly installing it.

OK NG NG
Insert is straight Insert is shallow Insert is incline
to the interior.
connector connector
connector

5 six screws
(+PWH 3 x 8 (SUMITITE))
connector connector connector
6 SMPS board
(EA, BR, AR, LA9, E12) /
SMPS (EMC) board
(US, CND, AEP, UK, RU,
MY, AUS, E4)

4 CN6500 (8P)

(US, CND, AEP, • Wire setting

UK, RU, MY, top side
8 four screws
(step screw M4) AUS, E4) core, ferrite
himelon 45

9 chassis

(US, CND, AEP,

7 acoustic tape UK, RU, MY,
AUS, E4)
chassis
• Wire setting SMPS (EMC) board
front side (US, CND, AEP, UK, RU, MY, AUS, E4)
acoustic tape

2 himelon 45

3 core, ferrite
(US, CND, AEP, UK, RU,
MY, AUS, E4)

1 CN6000 (2P)

chassis

18
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

2-11. FRONT PANEL (VANILLA) SECTION

1 three screws
(+ flat tapping 4 sound generator 12cm
screw - ED BK) 3 Slide out to remove the sound
generator 12cm in the direction
2 seven claws of the arrow.
q; Insert the jig into a space total seventeen bosses
and slowly remove the
panel, front (vanilla) section.
Note 1: When using a jig,
please work so as
not to injure
panel, front (vanilla) section
and speaker cabinet. 7 Slide out to remove the
sound generator 12cm
qs All bosses are removed while moving
in the direction of the arrow.
jig in the direction of the arrow, and
8 sound
panel, front (vanilla) section is removed.
generator 12cm
• Wire setting
top side
qd Push the protrusion, and
remove the terminal (wide side) [blue].

5 three screws
(+ flat tapping
loudspeaker screw - ED BK)
(5cm) (SP2)
VSSAMARA09 - 7/18/2022 5:25 AM 6 seven claws
qa Insert the jig into a space and
slowly remove the panel, front
protrusion (vanilla) section.
Note 1: When using a jig, please
work so as not to injure
panel, front (vanilla)
section and speaker
qd Push the protrusion, and remove cabinet.
the terminal (narrow side) [blue/black]. qs All bosses are removed while moving jig in the
direction of the arrow, and panel, front (vanilla)
qh panel, front (vanilla) section 9 three screws section is removed.
Note 2: When installing the ((4x13)(TR-184A))
panel, front (vanilla)
section, remove the used • Wire setting
glue and use a new glue to qf Push the protrusion, and top side
fix the panel, front remove the terminal
(vanilla). (narrow side) [red/black]. protrusion

qg Remove the
panel, front
(vanilla)
qf Push the protrusion, loudspeaker
section in the
and remove the (5cm) (SP4)
direction
terminal (wide side) [red].
of an arrow.

– Front view –

19
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.2

2-12. LOUDSPEAKER 30CM (WOOFER) (SP5)

• Wire setting
3 Push the protrusion, and remove
top side
the terminal (narrow side) [black].
3 Push the
protrusion,
and remove
the terminal
(wide side) [grey].

loudspeaker 30cm
(woofer) (SP5)
protrusion

terminal
(narrow side) [black]
• Installation direction for the loudspeaker
30CM (woofer) (SP5)
loudspeaker 30cm
(woofer) (SP5)
terminal position

terminal
(wide side)
[grey]

2 Remove the loudspeaker 30cm (woofer)

(SP5) in the direction of the arrow.

4 loudspeaker 30cm (woofer) (SP5)

1 eight screws
((4X16), +BV TAPPING) – Front view –

20
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.2

2-13. LOUDSPEAKER (12CM) (MID: L-CH) (SP1),

LOUDSPEAKER (12CM) (MID: R-CH) (SP3)

• Wire setting
3 Push the protrusion, and remove
• Installation direction for the loudspeaker (12CM), (SP3)
the terminal (narrow side) [blue].

terminal position
loudspeaker loudspeaker
(12cm) (SP1) (12cm) (SP3)

protrusion

terminal (narrow side)

[blue]
terminal (wide side) [black]
2 Remove the loudspeaker
3 Push the protrusion, and remove (12cm) (SP3) in the
the terminal (wide side) [black]. direction of the arrow.
terminal
(wide side) [black]

2 Remove the
loudspeaker (12cm) (SP1) terminal
in the direction of the arrow. (narrow side) [red]

4 loudspeaker (12cm)
(mid: L-CH) (SP1) VSSAMARA09 - 7/18/2022 5:25 AM

1 four screws
((4X16), +BV TAPPING)

1 four screws
((4X16), +BV TAPPING)

4 loudspeaker
(12cm) (mid: R-CH) (SP3)

– Front view – • Wire setting 3 Push the protrusion,

and remove the
terminal (wide side)
[black].

protrusion

3 Push the protrusion,

and remove the
terminal (narrow side) [red].

21
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

2-14. BOTTOM COVER SECTION

3 Insert the jig into a space and Note 3 : When you install
slowly remove the cover, bottom the connector,
section. please install them
Note 1: When using a jig, correctly.
please work so as not There is a possibility
to injure cover, bottom that this machine
section and speaker damages when not
cabinet. correctly installing it.
total five bosses
4 All bosses are removed OK
while moving jig in the Insert is straight
4 All bosses are removed
direction of the arrow, to the interior.
while moving jig in the
and cover, bottom section
direction of the arrow, connector
is removed.
and cover, bottom
section is removed.

3 Insert the jig into a

connector
space and slowly
remove the
cover, bottom section. NG
Note 1: When using Insert is shallow
a jig, please 3 Insert the jig into a space and
work so as not connector
slowly remove the cover, bottom
to injure cover, section.
bottom section Note 1: When using a jig,
and speaker please work so as not
cabinet. to injure cover, bottom
section and speaker
connector
cabinet.
1 four screws
NG
((4X13) (TR-184A))
2 three screws Insert is incline
((4X13) (TR-184A)) connector

6 Remove the cover, bottom

section in the direction of the
arrow.

5 CN4500 (8P) qs filament tape connector

8 CN4501 (4P) • Wire setting

rear
qg CN4460 (4P) side
q; one
screw
(+BVTP qf two screws filament
3 x 8) (+BVTP 3 x 8) tape
boss
qh 360 BACK L
board

qa EXTENSION 360 BACK L board

board

• Wire setting
qj two screws
rear
(+BVTP 3 x 8)
side

– Rear view – ql 360 BACK boss

R board
qd filament tape

9 CN4502 (4P)

7 cover, bottom section qk CN4490

filament 360 BACK R board
Note 2: When installing the cover, bottom (4P) tape
section, remove the used glue and use
a new glue to fix the cover, bottom section.

22
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
SECTION 3 Ver. 1.1

TEST MODE
PANEL TEST MODE COLD RESET
This mode is used to check the screen display panel, LEDs, but- This mode is used to reset all the user settings to factory setting.
tons, touch keys and GESTURE CONTROL sensor. Execute this mode when returning the set to the customer.
Procedure: Procedure:
1. Press [1] button to turn on the system. 1. Press [1] button to turn on the system.
2. Touch [] touch key and [MIC/GUITAR LEVEL -] touch key 2. Touch [] touch key and [MIC/GUITAR LEVEL +] touch
simultaneously for 3 seconds. key simultaneously for 3 seconds.
3. All LEDs and segments in screen display panel are lighted up. 3. “COLD RST” appears on the screen display panel. After that,
This is the display check mode. “SONY DEMO” appears on the screen display panel. The
Touch [N] touch key repeatedly to toggle different display system automatically turn on and off once. Please be sure that
mode as below: the system stay at demo mode finally before switch off the
Segments on screen display panel: power supply.
All On → 1st Group On → 2nd Group On → All On → All Off
Single color LEDs: DISC TRAY LOCK
All On → All Off → 1st Group On → 2nd Group On → All When the disc tray does not open and “LOCKED” appears on the
Off screen display panel, disc tray lock mode has been activated by the
Multi Color LEDs: shop front.
VSSAMARA09 - 7/18/2022 5:25 AM
All On → Red → Green → Blue → All Off
4. Touch [0 - ] touch key, the key check mode is activated.
To release from Disc Tray Lock Mode:
1. Press [1] button to turn on the system.
5. In the key check mode, the screen display panel displays 2. Touch [FUNCTION] touch key repeatedly to select the DVD/
“K 0”. CD function.
Each time a button/touch key is pressed/touched, “K” value 3. Touch [MEGA BASS] touch key and [VOCAL FADER]
increases. However, once a button/touch key has been touch key simultaneously and hold down until “UNLOCKED”
pressed/touched, it is no longer taken into account. After all displayed on the screen display panel.
the buttons and touch keys have been pressed/touched, “K”
value will toggle between “OK” and “K30”. SHOP FRONT DEMO
The screen display panel displays “<” or “>” or “U” or “u” on The playback started automatically and the “ * DEMO * ” appears
the right side of “K30 OK” each time swing left, right, up and on the screen display panel.
down at GESTURE CONTROL. This is the Shop Front Demo mode which is activated by the shop
6. To release from this mode, touch the touch keys in the same front.
manner as step 2, or disconnect the power cord.
To release from Shop Front Demo
MODEL, DESTINATION AND VERSION DISPLAY MODE 1. Touch [] touch key and [MIC ECHO] touch key simultane-
This mode is used to check the model, destination and software ously for 5 seconds.
version of the set. 2. The message "STANDBY" appears on screen display panel.
Procedure: After that, the screen display panel blinks for a few times and
1. Press [1] button to turn on the system. the system goes to demo mode.
2. Touch [] touch key and [MIC/GUITAR LEVEL -] touch key
simultaneously for 3 seconds.
All segments in screen display panel are lighted up.
3. Touch [0 +] touch key. Model information appears on the
screen display panel.
4. Touch [0 +] touch key. Destination information appears on
the screen display panel.
5. Touch [0 +] touch key. Serial number appears on the screen
display panel.
6. During serial number appears, touch [0 +] touch key. Each
time [0 +] touch key is touched, the screen display panel
shows the version of each category software in the following
sequence: SC, MTK, BT, BTE, PF, SUB and return back to
model information display.
7. Touch [] touch key and [MIC/GUITAR LEVEL -] touch key
simultaneously for 3 seconds to exit.

USER RESET
The user reset clears all data including preset data stored in the data
flash to initial conditions.
Procedure:
1. Press [1] button to turn on the system.
2. Touch [GUITAR] touch key and [MEGA BASS] touch key
simultaneously for 3 seconds.
3. “RESET” appears on the screen display panel. After that, the
screen display panel becomes blank for a while, and the system
goes to demo mode.

23
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1 SECTION 4
ELECTRICAL CHECK
TUNER SECTION 0 dB = 1 μV FOCUS BIAS CHECK

FM AUTO STOP CHECK oscilloscope

(DC range)
signal
generator MOTHERBOARD board
CN302 pin 17 (RF) +
CN302 pin 1 (GND) –
set
Procedure:
+
1. Connect the oscilloscope to CN302 pin 17 (RF) and CN302
75 pin 1 (GND) on the MOTHERBOARD board.
–
2. Press the [1] button to turn the power on, and touch the
[FUNCTION] touch key to select DVD function.
3. Set the test disc (CD: YEDS-18) on the tray and touch [N]
touch key to playback.
4. Confirm that oscilloscope waveform is as shown in the figure
Procedure:
below (eye pattern).
1. Turn the power on.
A good eye pattern means that the diamond shape (◊) in the
2. Input the following signal from Signal Generator to FM
center of the waveform can be clearly distinguished.
antenna input directly.
VOLT/DIV: 200 mV
Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz TIME/DIV: 500 ns
Deviation : 75 kHz
Modulation : 1 kHz
ANT input : 35 dBu (EMF) level:
1.1 ± 0.25 Vp-p (DVDSL)
Note: Please use 75 ohm “coaxial cable” to connect SG and the 1.0 ± 0.25 Vp-p (CD)
set. You cannot use video cable for checking.
Please use SG whose output impedance is 75 ohm.

3. Set to FM tuner function and scan the input FM signal with Checking Location:
automatic scanning. -COMPLETE MOTHERBOARD Board (COMPONENT SIDE)-
4. Confirm that input Frequency of A, B and C detected and
automatic scanning stops.

The stop of automatic scanning means “The station signal is

received in good condition”.

pin 1 (GND) pin 17 (RF)

CN302

24
SYS SET
 SMPS Board Diagnosis Flow

(2) AC IN
(1)
2020/04/28 00:01:32 (GMT+09:00)

(3)
The Power control signal to SMPS board is checked.
Is following power voltage OK? Check whether the state of the Cable and Outlet are normal.
No
If there are no problems, check circumference circuit for
Main ON Standby Demo mode Power On Main ON on Output of the Motherboard mount side.
NO6501:pin9 Low (0V) Hi (3.3V) Hi (3.3V)
(5)
Yes

(4) The Output from SMPS board is checked.

Is following power voltage up to standard?
No
Replaces SMPS board if it is not up to standard.
Standby Demo mode Power On
NO6501 pin 1,4,5 17.4±5V 17.4±5V 17.4±5V
CN6500 pin 6,7,8,9 58.5±5V 58.5±5V 58.5±5V
Yes
SECTION 5

(1) AC input (5) CN6500 connector

(2) Fuse Pin 1 : PGND END
(3) MAIN power transformer Pin 3 : PGND
TROUBLESHOOTING

(4) NO6501 connector Pin 4 : PGND

Pin 1 : Audio (+17V) Pin 5 : PGND
Pin 3 : Audio (GND) Pin 6 : PVDD (DC+58.5V)
Pin 4 : LED (+17V) Pin 7 : PVDD (DC+58.5V)

VSSAMARA09 - 7/18/2022 5:25 AM

Pin 5 : LED (+17V) Pin 8 : PVDD (DC+58.5V)
Pin 6 : LED (GND) Pin 9 : PVDD (DC+58.5V)
Pin 7 : LED (GND)
Pin 8 : AC DET
Pin 9 : Main ON
Pin 10: Network ON
Pin 11: Latch ON

25
MHC-V71/V71D
Ver. 1.1

SYS SET
 26
Optical Block Diagnosis Flow (1/2) Ver. 1.1

REMOVE SIDE PANEL

REMOVE TOP PANEL
TURN ON
MHC-V71/V71D

TRAY IN
2020/04/28 00:01:32 (GMT+09:00)

Does Optical pickup move to inner circumference? No Checks JL355 for +3.3V and CL308 for +1.2V No Checks IC303 circumference circuit for +1.2V.
(Visual check) REG IC303.
Checks IC009 (JL071) circumference circuit for +3.3V.
Does it output the power voltage of 3.3V and 1.2V?
Yes
Yes
Checks CN402 SL+/SL- signal. No Checks circumference circuit for SL+/SL- of IC401.
Does it output the signal? Checks circumference circuit of IC301 FMO Signal.
Yes
The Sled motor has a problem.
Replaces BU.

Does Spindle motor rotate? No Checks CN402 SP+/SP- signal. No Checks circumference circuit for SP+/SP of IC401.
(Visual check) Does it output the signal? Checks circumference circuit of IC301 DMO Signal.

Yes Yes
The Spindle motor has a problem.
Replaces BU.

Does Optical pickup do focus search? No Checks CN302 FCS+/FCS- signal. No Checks circumference circuit for FCS+/FCS- of IC401.
(Visual check) Does it output the signal? Checks circumference circuit of IC301 FOO Signal.

Yes Yes
The Optical pickup has a problem.
Replaces BU.

SYS SET
 Optical Block Diagnosis Flow (2/2)

A
2020/04/28 00:01:32 (GMT+09:00)

Does laser diode become luminous? No Checks JL306 (LD780) signal. No Checks circumference circuit of Q402.
(Visual check) Does it output 2V when laser become luminous? Checks circumference circuit of IC301 LDO1.
Yes Yes
The Optical pickup has a problem.
Replaces BU.

DISC IN
Yes

Is output level of RF signal JL317 up to standard? No If it is not up to standard,

RF Level = 1.05 ±0.45 Vpp
Lens cleaning is performed.
Test disc (CD: YEDS-18, DVD: HLX-503 (NTSC) or HLX-504 (PAL))
Yes
Yes
Is output level of RF signal JL317 up to standard?
No
RF Level = 1.05 ±0.45 Vpp Replaces BU if it is not up to standard.
Test disc (CD: YEDS-18, DVD: HLX-503 (NTSC) or HLX-504 (PAL))
VSSAMARA09 - 7/18/2022 5:25 AM

Yes
Is there no problem with Long term Aging Test (60min)?
Confirms that there is no sound skip. No
Yes
The Optical pickup has a problem.
Replaces BU.

END

27
MHC-V71/V71D
Ver. 1.1

SYS SET
 28
MOTHERBOARD Board Mount Amplifier Diagnosis Flow (1/3) Ver. 1.1

1. “PROTECT3” is displayed after turning the power on

“PROTECT3” is displayed on the screen display panel after turning the

power on.
MHC-V71/V71D

Yes

“PROTECT3” is not displayed, when removing the speaker connector Yes Check and replace the speaker.
(CN2021) and turning the power on.
2020/04/28 00:01:32 (GMT+09:00)

No

Check that IC2002 pin 27, 32, 35 and 39 is short to GND. Yes Exchange IC2002.

No

MOTHERBOARD board damaged. Exchange complete MOTHERBOARD

board.

SYS SET
 MOTHERBOARD Board Mount Amplifier Diagnosis Flow (2/3)
2. The sound is not outputted

The sound is not outputted.

2020/04/28 00:01:32 (GMT+09:00)

Yes

Check that the signal is input to IC2001 pin 24 and 25. No MOTHERBOARD board damaged. Exchange complete MOTHERBOARD
board.

Yes

Check that the PWM signal is outputted from IC2001 pin 38, 39, 40 No Exchange IC2001.
and 41.

Yes

Check that the signal is outputted from IC2002 pin35 (Right Channel No
Speaker), pin 39 (Left Channel Speaker), and pin 27 and 32 Exchange IC2002.
(Subwoofer Speaker).

Yes

MOTHERBOARD board damaged. Exchange complete MOTHERBOARD

board.
VSSAMARA09 - 7/18/2022 5:25 AM

29
MHC-V71/V71D
Ver. 1.1

SYS SET
 SYS SET
These terminal's resistance value should not be near to 0Ω (short).
Please check each channel’s resistance value for the Coil’s terminal and Capacitor’s + and – terminal.
<Note>
4 3
JL2029
CN900

JL110
2 1

JL102
C2151

JL111
JL900 JL620

JL101
JL901
 JL631 JL905

L900
C1013 CL2052

C636
D900
R937 JL619 C1005 C638 CL2050 CL2048 CL2049 JL2030

C1010 C1009
R2206 R1026 L601
C180 JL1003
C930 CL2051 CL2041

L901

IC1000
2 3
4
C932

C2200

L605

R1022
R939
R940 C1003

1
CL2046

5
C931 C933
JL635

L902

C934
1 C660 R1024 C1004

R1017
R651
Q605
65 20

C665
CL2047

R1023
21
C2203

X900
R944

4
5
IC902

R1027
16

C936
10
R685 CL2045

C181
11 15
Q303

1
R686

JL2221
C2227

R689
Tester R1025

R2226
JL604
R943 JL618 C1011 IC1001

R946
C2228
R359

CL2040
JL605

R857
Q302

R947
R2208 R945 CL380

CL2044
C306 JL2026
R324

JL2222
C348

R309
C364
C347 C352

JL2021
C650

C647
C657

JL330
C346 R370

JL2020
CL395 JL2035

CL2042
C652 C351

C375

CL307
C359

CL2043
C343 R319

JL2223

R912

R671

CL309
C372 C315
CL308

R382
R303 R302 R321

C344
R914

R911
JL2200

JL355 C321
C643 R663
3 1 C340 CL316 CL310

R381
JL2224 R669 RB310 C339 R360
Tester

R662
R913
C641 C338
IC303 4

CL313 CL311
JL2206 6 C342 R358

C334
R339
R1008

R328
C360
C373 C369 Tester

C326
C358 Tester

C350
R330

C328
JL2203

CL315
C331

C365
L301 JL362 C330

R352
R348 C325

JL358

R325
JL359 C319

JL357
C357

C363

R326


JL356
R657 Tester

R660

C336
JL361

C316
C952C951

C954
C963
R664 R658

C662
R639

JL2012
JL2015
JL603 X602
R955

R665
R953 C950

C640

C648

JL2005
C981

C726

48
C663 C960

C985
R661

37
1
R674

36

JL2018 JL2011
R981

JL2006
JL2016
C695
 R982

R983
R637

IC904
R690
R794
R785 R984
JL2207 R985

JL2009
R677

C644
C622 R986

R959
24 25
C642

R687

R783 R778

13
12
C646
14 8
R957

C609
R807
Q612 C617 IC606 C949

CL401
C645 R815

C711
CL402 1 7

JL313
28
1
CL408 R691
CL403
C649 C653 R688

CL404
C407 JL2003
CL409 R951 R952

R950
R406
C413 C987 JL2036

CL413
JL305
C655

22
7
R407 R411 R412

R435
CL405
CL2024
IC401

C409 R418
JL360 IC452

R451

JL307
Tester

29

30

R314

C466

JL311

R432
R431

JL2008
CL414
R453
Q304

R389

C423

JL303
JL308 JL309
6 4
C404 C465
R313

21
8

Q305
CL410

JL321
3
FB455

JL315
JL319
1

JL317
JL314
C463
R498
JL462 Tester

JL316
JL310

JL306
JL302
CL412 C2019
R318

CL415
CL411 C462 R310 Tester

CL2025
C408 R478

15

JL463
14
JL304

JL322
JL2038

JL323
JL050 JL461

Q402
JL460 JL320 R2022

C406
C405
CL2021

JL329
CL2035

C311

C424
JL401 R2021 CL2020 JL2040 JL2037

JL301

R316
JL318
JL324
CL2036 JL2034

JL326

R429
C367
JL328

JL312
C066
JL023 CL2023
  CL2022
JL406 JL402  JL2039

D1001
JL405

R529
Q005

R148
C064 R534
JL022
R526

Q1001
R034

JL130
R1002 R1001 R230

JL327
R1006

JL325
Q459

JL294
R1007

R528
Q1002
R028

R174
Q1000
R037

JL070

C1001
JL138 JL136 R527

C1000
R1003
Q1005

R1005
JL143 R1004 R273
JL021 JL146 JL024 R514

R215
JL145 JL209

R512
FB107
FB108
JL149 R254
JL144 JL212 FB109 C146 C501 C137 C133 R513

R091

C2000
JL142 R119 R237 C135

C503
C140
FB106

C148
JL525
RB106
R222

R533
C095 R259

C111
JL137 R274

R524
JL524 C164 R300
1 C153

R515
R097 IC003
R255

4
IC002
3

R170
R284
C502
C506

C168
C154 R293
C102

R120
1
R094

8
R282

R129
6

R143
C008
4
JL147 C507

C112
C065 R187
IC106

RB104
JL528
R516 JL269

CL2026
C097

JL287
14 8
C087 JL230

C155
R103 R522

R107
4

RB105
JL002

C114

R140
IC102

JL527
JL526
C504

R507
C012

R139
JL231 C115 JL150
JL139 C156

C157
R102

R137
JL194
JL232 1 7

JL529
JL141 R2146
R235
IC2003

C2116
R505 C280 R149

C158
JL530
JL521 C281 R104

C118

C2127
R184
R177

R131
R135 R283
R134 C283
R123

R175
JL520

JL148
R178

R176
JL523 C117

C159
JL522 C160 C2128

CL2011
C282 TH571

JL2031
R276 C120 R249

R532
JL140 R256 RB101 C122
R298 R152
JL123 JL124 C131

JL155

CL2010
CL2004
R145
C144 C138

JL119
JL107
JL122 JL115 C147 C136 C134

JL151
JL135 JL121 JL289

JL154
JL120 R195 JL109 R518
C299

R543
JL152 R122 R546

R203

R049
JL106 R050

R220
JL132 R106

R544
R545
JL134 JL118 JL116 C061
JL297 JL153 JL117 IC010 6
R046
JL2033
JL131 4
JL105

JL069
3

R3009
C675
1 R045
JL227
C060 CL2038

R917 C670 R711

R709

R3014
2020/04/28 00:01:32 (GMT+09:00)

C669 JL176
R719

JL195
R722
R3015 JL044

C667
JL617 JL175 Q011 R068

CL3003
R708 JL174 JL059 CL2039
14 8
IC609

JL197
JL235
JL172 JL173 JL008
JL169

JL199
JL125 C666

JL205
R720 R723
JL108

JL215
JL001

R191
1 7 JL171 R064

C672
C3019

R065
R018
R053

R066
JL201
JL206
C673 C678 JL012
C062

JL196
2 1 R015

JL200

JL198
JL203
JL204

JL202
JL601 C032

JL071
3 4 C674 R069

JL068
6 4
IC3001

JL216
C671
C3018
C986

JL615
C3000 Q012

R031
JL910 JL004

JL072
1 3

R020
R3032

JL217
MHC-V71/V71D

JL114 R019 JL045

CL3058 IC007

CL3059
CL3006 R792 Q461
CL3001 R3049 JL614

R3040

JL908
JL909
R3043 C031 JL046

R3046
JL113

JL049
JL616
CL3008

R033
R3044
R3048
R3045

JL613

Q004
CL3002

R035
R3041

R3004
R029

R060
R3047
JL048
R3005 2 1 2 1 JL073 2 1
CL3009 C078
R3039 R3003

C080
R3042 JL047 C079 C051
JL011
IC006 IC004 IC008 JL005
3 3 3
Ver. 1.1 IC2002 Confirmation for MOTHERBOARD Mount

30
 MOTHERBOARD Board Mount Amplifier Dianogsis Flow (3/3)
3. IC and MOTHERBOARD board after replace checking guide
After IC2002 and MOTHERBOARD board changed, check as below:

Assembly back the set.

Make sure connect the connector (CN2021).
2020/04/28 00:01:32 (GMT+09:00)

Volume set to Max, sound field set to default, Mega Bass set to “ON”. Exchange original damaged IC.

Yes
Play song “Billie Jean By Michael Jackson” for 2 minutes. Check for any Yes First time repair?
abnormality:
Protect 3 displayed/ Set Reset to DEMO/ No display etc.

No No

Repair is successful. MOTHERBOARD board damaged. Exchange complete MOTHERBOARD

board.

31
MHC-V71/V71D
Ver. 1.1

SYS SET
VSSAMARA09 - 7/18/2022 5:25 A
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1 SECTION 6
DIAGRAMS
• Circuit Boards Location

VFD board
SENSOR board

MIC USB board

POWER KEY board

SMPS board (EA, BR, AR,

LA9, E12) / SMPS (EMC)
board (US, CND, AEP, NFC board
UK, RU, MY, AUS, E4)

MS-476 board MOTHERBOARD board

IR board
360 BACK L board
HUB board (US, CND, AEP,
UK, RU, MY, AUS, E4) /
HUB //NON-EMC board EXTENSION board
(EA, BR, AR, LA9, E12)
SPK MID L board
SPK MID R board

360 FR L board 360 BACK R board

SW LED L board

360 FR R board

SW LED R board

32
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

6-1. BLOCK DIAGRAM - MAIN Section (1/2) -

V71D

>001B STEREO A/D CONVERTER

DIR_CP_TUNER_SDA IC904
MAIN SECTION(2/2) DIR_CD_TUNER_SCL
(Page 34) TUNER BT BCK
TUNER BT LRCK
TUNER BT DATA

>002B
ARC_SPDIF ARC-SPDIF
CD/DVD, USB, HDMI SECTION 32 RXIN3
MKT-BCK MKT-BCK
30 RXIN5/ABCK_IO
(Page 36) MKT-LRCK MKT-LRCK
29 RXIN6/ALRCK_IO
ASDATA0 ASDATA0
J601,J602 28 RXIN7/ADIN_O
MKT-MCK
47 VINL
L Rch 48 VINR
AUDIO/PARTY
CHAIN OUT ANALOG AUDIO +3dB AMP
R R-CH SELECTOR IC601
IC602
24 MDI/SDA
L 5 Y1 Y 3 3 1 25 MC/SCL
AUDIO/PARTY LPF
CHAIN IN (TV) IC603
R R-CH
LINK SET
Q603 3 1 1 Y0
A B MUTING
10 9 CIRCUIT
MIC AMP Q602,Q606
IC4100

J4100
3 1 ANALOG
MIC1 SELECTOR
Q612
5 7
4 MPIO_A1
V71

DAC SIGNAL SELECTOR

IC604 IC610

MODE 1 BCK VOUTL 7 15 1Y2 A 10

J4101
SELECT
MIC2 3 LRCK 2 2Y2 B 9
Q4109, Q4110,
GUITAR Q4107, Q4108 16 SCK 4 2Y3 2Y1 5 12 MPIO_B1/ABCK_I2
2 DATA VOUTR 8 Rch 11 1Y3 1Y1 14 13 MPIO_B2/ALRCK_I2

ADC SIGNAL SELECTOR

IC609 IC611

14 VINR 15 1Y2 A 10
VINL
VSSAMARA09 - 7/18/2022 5:25 AM 13
8
7
BCK
LRCK
B 9

11 1Y3 1Y1 14 14 MPIO_B3/ADIN2

6 SCKI DOUT 9

ADC
IC606

Rch 14 VINR
LRCK 7 9 MPIO_C2/ALRCK_I1
13 VINL BCK 8 8 MPIO_C1/ABCK_I1
6 SCKI DOUT 9 10 MPIO_C3/ADIN_1
SERIAL FLASH
IC106

ERROR/INT0
Rch

NPCM/INT1
BIAS DETECTION
>003B Q605,Q607

DOUT
LRCK
BCK
RST
DI(SIO0)
ARAGON-BCK0

DO(IO1)
AMP SECTION
ARAGON-LRCK

CLK
1 2 17 18 19 34

IO3
IO2
(Page 35)

CS
ARAGON-MCK
1 6 7 3 5 2
X105 X103 X104
13.33MHz 12.288MHz 48MHz
• Signal path
: TUNER (FM) 120 52 175 96 114 29 30 43 32 70 71 91 92 139 140 47 33 169 168 167 166 170 172 48 42 41 28 26 24 38
: AUDIO (DIGITAL)

I2S_SELECT_B(CD)
MIC-DET2
MIC-DET1
LINK-SET

GUITAR_DIS/SD_PCON

MODE-SEL

SSIO_BCK0
SSIO_LRCK0

AUDIO-CLK-OUT
SSIO_DO

EXTAL

XTAL

AUDIO-X1

AUDIO-X2

USB-X1

USB-X2

LINK-DET

SSIO_DI

Q-Flash-CS
Q-Flash-CLK

I2S_SELECT_A(CD)
Q-Flash-SIO3
Q-Flash-SIO2
Q-Flash-SIO0
Q-Flash-SIO1

/LINE MUTE

SSI3-DI
SSI3-LRCK0
SSI3-BCK0
DIR-RESET/SD_LED1
DIR-INT0(DVD)/

DIR-INT1(DVD)/
: AUDIO (ANALOG)
: MIC SYSTEM CONTROL
IC109 (1/6)
• R-ch is omitted due to
same as L-ch.

MHC-V71/V71D
33 33
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

6-2. BLOCK DIAGRAM - MAIN Section (2/2) -

>001B
TUNER BT DATA
MAIN SECTION(1/2)
TUNER BT LRCK
(Page 33)
TUNER BT BCK
DIR_CP_TUNER_SCL
DIR_CP_TUNER_SDA
FM DRIVER
SYSTEM CONTROL
(FM RECEIVER)
CN900 IC109 (2/6)
IC902
ANTENNA 2
FM 1 FRF1 IIC/RDSI 6 45 ST-RDS
CK 8 125 DIR-CP-TUNER-SCL
AUTHENTICATION DA 11 126 DIR-CP-TUNER-SDA
COPROCESSOR BLUETOOTH (STEREO AUDIO MODULE)
IC3000 CP3000
IISD 14
LRCK/LOUT 13
SDA 2 16 P1_3(CP_SDA)
BCLK/ROUT 12
SCL 6 15 P1_2(CP_SCL)
RST 7 29 P3_7(CP_RST)

SIGNAL SELECT

RFS0 (BM64_LRCK)
SCLK0 (BM64_BCK)
IC905

DT0 (BM64_DATA)
11 3A 3Y 9
1Y 4

HCI_RXD
2 1A

HCI_TXD

ADAP_IN
RST_N
5 2A 2Y 7

P2_0
P2_7
MFB

EAN
RESET
IC3001 2 3 4 26 13 20 19 23 32 41 42

BT3.3V 2 VDD VOUT 4

3 1B
6 2B
BM64_LRCK
1 10 3B
BM64_BCK SELECT 1 108 BT-TUNER-SEL/
3 TEST_MON108/SD_CLK
BM64_DATA
5
MFB
6 164 MFB
BT-RESET
7 113 BT-RESET/SD_CD_0
BUS BUFFER
IC102 (1/2)

HCI_TXD/BT-RXD
8 5 2A 2Y 6 65 BT-RXD(MD-CLK)
BLUETOOTH
HCI_RXD/BT-TXD
9 133 BT-TXD
ADAP_IN
10 132 USB-DET
EAN
11 165 EAN
BLUETOOTH
BT_3.3V
12 POWER CONTROL 16 BT-ON
Q103, Q104

131 P27
P20
13 124 P20

NFC MODULE
IC001

RFDET 7 137 NFC-RF-DET

2 PWRM SCL 6 129 TOUCH-NFC_SCL
NFC
3 PWRP SDA 5 130 TOUCH-NFC_SDA
IRQ 1
>004B
TOUCH, LED TOUCH-DATA
DRIVER SECTION TOUCH-CLK
3D-RESET
(Page 37)
3D-DETECT

110 NFC-INT/TEST-MON110/SD_D0_0
111 3D-DETECT/SD_D1_0
103 3D-RESET/TEST-MON103/SD_D2_0

• Signal path
: TUNER (FM)
: BLUETOOTH

MHC-V71/V71D
34 34
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

6-3. BLOCK DIAGRAM - AMP Section -

AUDIO CODEC DIGITAL POWER AMP
IC2001 IC2002

>003B
ARAGON-MCK
MAIN SECTION (1/2) 11 MCLK PWM_P_2 41 14 INPUT_C OUT_C 32
ARAGON-LRCK TWEETER
(Page 33) 22 LRCLK PWM_P_1 39 15 INPUT_D
（L-CH）
ARAGON-SCLK
23 SCLK

SYSTEM CONTROL
VSSAMARA09 - 7/18/2022 5:25 AM
IC109 (3/6)

OUT_D_27 27

VALID 37 4 RESET OUT_D_28 28

SSI2-D0 (FR) 40 TWEETER

25 SDIN2
（R-CH）

3D(GESTURE)-PWM-SDA 128 20 SDA

3D(GESTURE)-PWM-SCL 127 21 SCL
/AMP-RESET 53 16 RESET
DAMP-MUTE 57 19 MUTE
OUT_B 35
SSI1_D0 (TW) 54 24 SDIN1

WOOFER

OUT_A_39 39

OUT_A_40 40

/SD-FAST 49 16 FAULT FAN MOTOR

+5.2V
DRIVER
Q2006

+5.2V REG.
+13V IC2003 FAN MOTOR
FAN RESET DRIVER
SWITCH Q2000
CN2001
Q2005
TO FAN

FAN
AMP-PROTECT 78 PROTECTION
(LOCK)
Q2002

• Signal path
: AUDIO (ANALOG)
: AUDIO (DIGITAL)

MHC-V71/V71D
35 35
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

6-4. BLOCK DIAGRAM - CD/DVD, USB, HDMI Section -

FOCUS/TRACKING ERROR AMP

CD/DVD SYSTEM PROCESSOR V71D
SERVICE, OPTICAL DEVICE (7G)
DIGITAL SERVO PROCESSOR
CN302
IC301 J601

RF 119 RFIP CVBS 98 VIDEO OUT

MTK-LRCK
ALS/ALRCK GPIO 114
ASDATA0
CENTER/ASDATA0 GPIO 115
MTK-MCK >002B
VOA/A 125 RFC LFE/ACLK GPIO 109
MTK-BCK
VOB/B 124 RFB ARS/ABCK GPIO 110 MAIN SECTION (1/2)
VOC/C 123 RFA SERIAL FLASH
(Page 33)

ARC_SPDIF
VOD/D 126 RFD IC302

VC 5 V20 SF_DO 25 2 DO(IO1)

DI(IO0) V71D
SF_DI 26 5
PD 8 MDI1
SF_CK 27 6 CLK ARC BUFFER
AUTOMATIC POWER SF_CS_ 24 1 CS IC1001
FE_LD_CD (780) CONTROL (FOR CD) 128 FE_CD_IOP- SD-RAM
Q402 IC306
3 2A 2Y 5
9 LDO1 RD0 - RD15 DQ0 - DQ15

AUTOMATIC POWER
FE_LD_DVD (650) CONTROL (FOR DVD) 127 FE_DVD_IOP- RA0 - RA11 A0 - A11
Q401
BA0 72 20 BA0
10 LDO2 BA1 73 21 BA1
RCLK 60 38 CLK
(LO:DVD.HI:CD)MSW 18 MSW RWE 68 16 WE
CAS 69 17 CAS
CD_VR (780) 14 CD_VR RAS 70 18 RAS
DVD_VR (650) 15 DVD_VR DQM0 49 15 LDQM
DQM1 59 39 UDQM CN1000
ARC 14
5CH SYSTEM MOTOR DRIVER DATA2+
TX2P 94 1
IC401 DATA2-
TX2N 93 3
DATA1+ 4
TX1P 91
SP+ 11 VOSL+ DATA1- 6
VINSL+ 4 12 DMO TX1N 90
SP- 12 VOSL- DATA0+ 7
TX0P 88
DATA0- 9
TX0N 87
SL+ 17 VOLD+ CLOCK+ 10
VINLD 23 13 FMO TXCP 85
SL- 18 VOLD- CLOCK- 12
TXCN 84
SCL (5V) HDMI OUT
HDMI_SCL 28 15 (TV) ARC
FE_TRK+ 16 VOTK- SDA (5V) 16
VINTK 26 16 TRO HDMI_SDA 29
FE_TRK- 15 VOTK+ HOT PLUG DET 19
HPLG 81
+5V REG
FE_FCS+ 14 VOFC+ IC1000
VINFC 1 17 FOO
FE_FCS- 13 VOFC- POWER +5V POWER
AVDD33_12 83 SUPPLY DVDD3.3V AVDD+9V 5 VIN VOUT 4 18
Q302, Q303 CONT
MUTE 28 108 MUTE
XTALO 4 1 HDMI CEC
BIAS 27 6 V14 X301 CONTROL CEC
13
27MHz Q1000, Q1001,
XTALI 3 Q1002, Q1005

USB SWITCH CONTROL

IC453
CN4100
USBP 19 5 HSD1+
3
7 HSD2+ D+ 1 D+
USBM 20 4 HSD1-
2
6 HSD2- D- 2 D-
REC/PLAY 5V 1A
XSYSRST

10 S USB POWER CONTROL

XIFBSY

IC452
IFSDO
IFSCK
IFCS_
IFSDI

8 OE
4 /FLAG 1
35 38 37 34 36 32 OUT 6 VBUS
3 EN

MS-476 BOARD 22 20 17 19 104 14 151 150 106 59 15 10 35 112

CN303
USB-HOST-SEL

MTK-POWER-CTRL

CEC_OUT (DVD)
CEC_IN (DVD)
USB-OC
VBUS-OE
MTK-BUSY
MTK-RESET
MTK-SDO
MTK-SDI
MTK-CLK
MTK-XIFCS

DP0
DM0

• Signal path
LOAD+ 10 VOTR+ FWD 6 8 CD-MOTOR+
LOAD- 9 VOTR- 7 3 CD-MOTOR-
: TUNER (FM)
REV
SYSTEM CONTROL : CD/DVD PLAY
IC109 (4/6)
TRAY-IN 12 CDM-LOAD-SW : VIDEO
TRAY-OUT 13 CDM-UNLOAD-SW : USB

MHC-V71/V71D
36 36
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

6-5. BLOCK DIAGRAM - TOUCH, LED DRIVER Section -

TOUCH SENSOR CONTROL M+5.2V

SYSTEM CONTROL LED DRIVER LED DRIVER
IC5200
IC109 (5/6) IC5002 IC4300
D5200
SIN_VOL MEGABASS LED DRIVE
JL5229 GESTURE ON/OFF 1 CS0/PS0 SOUT 22 2 SIN OUT14 19
Q5008,Q5009
JL5213 SAMPLER 2 CS1/PS1 I2CSDA 21 M+5.2V D4470
JL5214 TUNING -
3 CS2/GUARD I2CSCL 22 RED HILED
. OUT8 13
TOUCH_INT_1 D5003
JL5212 DJ 4 CS3 HI/BUZ/GPO7 23 51 TOUCH-INT1 2 SIN BT_LED OUT9 14
OUT2 7
D4471
TOUCH_RESET1 GREEN HILED PARTY
XRES 24 1 MEGA_BASS_LED/TOUCH-RESET1 OUT10 15
JL5200 FIESTA 19 CS5 D4430 LIGHT L
3 SCK MID_LED_R 3 SCK OUT11 16
-PARTY CHAIN OUT12 17
JL5207 18 CS6 D4472
PARTY LIGHT
BLUE HILED
JL5203 WIRELESS PARTY CHAIN 17 CS7 D4420 OUT12 17
4 TRANS MID_LED_L 4 TRANS OUT13 18
JL5205 MEGA BASS 16 CS8/GPO0 OUT13 18
D4482
JL5223 15 CS9/GPO1 BLUE HILED
D4450 OUT2 7
JL5204 -PAIRING 14 CS10/GPO2 21 PWMCLK SPK_LED_R 21 PWMCLK OUT3 8
BLUETOOTH OUT14 19
JL5202 FUNCTION 13 CS11/GPO3 D4481
GREEN HILED PARTY
D4440 OUT4 9
JL5209 N 12 CS12/GPO4 LIGHT R
SPK_LED_L OUT5 10
OUT15 20
JL5211 x 11 CS13/GPO5 D4480
RED HILED
JL5210 PLAYBACK 10 CS14/GPO6 OUT6 11
OUT7 12

TOUCH SENSOR CONTROL

IC5201

LED DRIVER LED DRIVER M+5.2V

JL5217 - 1 CS0/PS0 IC5001 IC2200
I2CSDA 21
JL5220 MIC/GUITAR LEVEL - 2 CS1/PS1 D4460
22 SOUT RED HILED
I2CSCL 22 OUT9 14
JL5225 MIC ECHO 3 CS2/GUARD
RGB_SD OUT10 15
RGB-SOUT 117 2 SIN 2 SIN
D4461
JL5206 SOUND FIELD 20 CS4 GREEN HILED 360° BACK
OUT11 16
LIGHT L
JL5216 KARAOKE 19 CS5 RGB_SCLK OUT12 17
RGB-SCLK 134 3 SCK 3 SCK
D4462
JL5218 VOLUME - 18 CS6 BLUE HILED
D5005 OUT13 18
JL5215 TUNING + 17 CS7 GUITAR_LED
> RGB_TRANS OUT15 20 M+5.2V OUT14 19
RGB-TRANS-PNL-LED/SPK-LED 115 4 TRANS 4 TRANS
JL5219  16 CS8/GPO0 D4490
RED HILED
JL5228 VOLUME + 15 CS9/GPO1 OUT5 10
RGB_PWM OUT6 11
JL5226 + 14 CS10/GPO2 RGB-PWM-CLK 136 21 PWMCLK 21 PWMCLK
D4491
JL5227 MIC/GUITAR LEVEL + 13 CS11/GPO3 GREEN HILED 360° BACK
OUT3 8
LIGHT R
JL5222 VOCAL FADER 12 CS12/GPO4 TOUCH_INT_2 OUT4 9
HI/BUZ/GPO7 23 56 BT-LED/TOUCH_INT2
D4492
JL5224 GUITAR 11 CS13/GPO5 BLUE HILED
TOUCH-RESET2 OUT1 6
JL5221 VOICE CHANGER 10 CS14/GPO6 XRES 24 94 AC_LOW_DET/TOUCH-RESET2 OUT2 7

3D-PWM_SDA
128 3D(GESTURE)-PWM-SDA
GESTURE CONTROL
IC5300 3D-PWM_SCL
127 3D(GESTURE)-PWM-SCL
RGB-TRANS-LED
CL5326 TRANSMITTER 15 TXD RGB-TRANS-LED 173
EIO4/SI0 9
CL5329 EAST ELECRODE VSSAMARA09 - 7/18/2022 5:25 AM
21 RX0
EIO5/SI1 10
TOUCH_DATA
CL5328 SOUTH ELECRODE 23 RX2
TOUCH_CLK
CL5325 WEST ELECRODE 24 RX3 3D-DETECT >004B
EIO0 1
CL5327 NORTH ELECRODE 25 RX4 3D-RESET
/MCLR 13
MAIN SECTION (2/2)
(Page 34)

MHC-V71/V71D
37 37
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

6-6. BLOCK DIAGRAM - PANEL, POWER SUPPLY Section (1/2) -

>005B
MAIN ON PANEL, POWER
SYSTEM CONTROL +13V SUPPLY SECTION (2/2)
REMOTE CONTROL IC109 (6/6) (Page 39)
RECEIVER
IC4200 POWER DISTRIBUTION
PROTECTION CONTROL
PCONT-DAMP 118 SWITCH
Q576
IC003
VO 1 135 SIRCS
PROTECTION CONTROL M+5.2V_PNL 6 OUT IN 1
Q575 4 FLAG EN 3

+5V/ +5.2V REG.

PROTECTION CONTROL POWER DISTRIBUTION IC001
1 S4221 6 POWER-KEY SPM-C-MON 79 SWITCH
Q574
IC010
USB +5V 3 SW1 VIN1 1
PROTECTION CONTROL M+5.2V 6 OUT IN 1 M +5.2V 14 SW2 VIN2 16
Q572 4 FLAG EN 3
TAIKO S4220 84 AD-KEY0/TAIKO-KEY

PROTECTION CONTROL
C-CONT 55 Q571
FE_5.2V_M POWER CONTROL
FE_5.2V_TRAY PROTECTION
Q459
THERMOSTAT
SPM-AMBIENT-TEMP 80 TH571
11 PG2
PROTECTOR 82 POWER CONTROL 6 PG1
PROTECTION 5 EN1
Q457 (1/2) 12 EN2

USB-OE/SD_LED0 35
LOW_AC/PCONT-BTSTBY
VBUS-OE/SD_WP_0 112
PCONT-BTSTBY 122 +3.3V/ +1.2V REG.
POWER DISTRIBUTION IC009
VOLTAGE DETECTOR SWITCH
IC103 IC007 VIN1 1
E +3.3V E +1.2V 3 SW1
VIN2 16
RES 76 4 VOUT VDD 2 6 OUT IN 1 EN1 5
4 FLAG EN 3 14 SW2 EN2 12
POWER CONTROL
PROTECTION 6 PG1
Q009 11 PG2

POWER CONTROL POWER CONTROL

D +3.3V PROTECTION DVDD +3.3V PROTECTION
+1.2V REG. Q005
Q008 +1.2V
IC303
POWER CONTROL POWER CONTROL
PROTECTION +3.3V PROTECTION
Q457 (2/2) Q110
POWER CONTROL +12V REG.
+3.3V PROTECTION IC2000
Q304
POWER CONTROL
+12V 3 OUT IN 1 PROTECTION
Q111
AVDD +5V POWER CONTROL AVDD +9V
PROTECTION
Q305
POWER CONTROL
+3.3V REG. +5V REG. +9V REG.
FL DISPLAY/ +3.3V PROTECTION
IC903 IC006 IC004
FL DRIVER Q004
ND4000
ST-CE 44
DIN 5 FL-SOUT +12V REG. POWER CONTROL
+12V PROTECTION
POWER CONTROL IC008 +12V REG.
V71 Q461
DVDD +5V PROTECTION IC002
Q007
CLK 2 FL-CLK
+3.3V REG. SW +12V 1 VOUT VIN 6
+3.3V POWER CONTROL
IC305
V71D ON/OFF 3 SW +13V PROTECTION
POWER CONTROL Q011
STB 176 FL-LATCH MTK-POWER-CTRL 59 PROTECTION
Q006
POWER CONTROL
PCONT-PSAVE-PROTECT 60 PROTECTION
VIN BUS BUFFER Q012
IC102 (2/2)

+6V REG. AC CUT SWITCH AC-DET

F+ SW +12V AC-CUT(MD-BOOT0) 63 11 4Y 4A 12
IC4000 Q107

LATCH ON
F- LATCH-ON 27
D4000

MHC-V71/V71D
38 38
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

6-7. BLOCK DIAGRAM - PANEL, POWER SUPPLY Section (2/2) -

DIGITAL POWER AMP
IC2002

29 PVDD_CD

30 PVDD_CD

31 PVDD_CD

TRANSFORMER
36 PVDD_AB
D6000 T6300

2 18 D6504 37 PVDD_AB

17 38 PVDD_AB
3
SWITCHING MODE POWER 16
SUPPLY CONTROL
IC6300 4
D6307 15 D6501
DRIVER F6500
DRV 5 Q6300, Q6301, 5 14
VSSAMARA09 - 7/18/2022 5:25 AM Q6302, Q6303
D6312 13
>005B
JL6510 MAIN ON
D6340
7 SWITCH PANEL, POWER
12 Q6504
SUPPLY SECTION (1/2)
D6341 8 11 (Page 38)
CS 3 8 10
SWITCH JL6511 LOW_AC/PCONT-BTSTBY
Q6501

REGULATOR
VCC 6
Q6304, D6308

D6313

CN6000 D6311
LF6001
AC INLET D6001
TH6000
JL6503 +13V
8 HV LATCH 1
F6000

VR6000 TH6300 D6306

JL6506

SHUNT
REGULATOR
IC6500, PH6301

FB 2
FEEDBACK
CIRCUIT
GND 4

SWITCH Q6506, Q6507,

Q6305 D6509, D6510,
D6511, D6515, D6516
POWER UP
PH6302
UVP JL6512 LATCH ON
CIRCUIT

AC DETECTOR
PH6300

SWITCH AC DET JL6509 DC DET

Q6307 Q6500

MHC-V71/V71D
39 39
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.2

• Note for Printed Wiring Boards and Schematic Diagrams

Note on Printed Wiring Board: Note on Schematic Diagram:

• X : parts extracted from the component side. • All capacitors are in µF unless otherwise noted. (p: pF)
• : parts extracted from the conductor side. 50 V or less are not indicated except for electrolytics
• : Pattern from the side which enables seeing. and tantalums.
(The other layer’s patterns are not indicated.) • All resistors are in Ω and 1/4 W or less unless otherwise
specified.
Caution: • 2 : nonflammable resistor.
Pattern face side: Parts on the pattern face side seen • C : panel designation.
(Conductor Side) from the pattern face are indicated.
Parts face side: Parts on the parts face side seen from The components identified by mark 0
(Component Side) the parts face are indicated. or dotted line with mark 0 are critical for
safety.
• Indication of transistor Replace only with part number specified.
C Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Q These are omitted. Ne les remplacer que par une piéce portant
B E le numéro spécifié.

• A : B+ Line.
• B : B– Line.
D
• H : Adjustment for repair.
Q These are omitted. • Voltage and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
G S
no mark : TUNER
* : Impossible to measure
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Q Voltage variations may be noted due to normal production
tolerances.
B C E • Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
These are omitted. tolerances.
• Circled numbers refer to waveforms.
Q • Signal path.
J : AUDIO (DIGITAL)
B C E F : AUDIO (ANALOG)
f : TUNER (FM)
These are omitted. L : VIDEO
E : USB
Note 1: W hen the MOTHERBOARD board is replaced, J : CD/DVD PLAY
spread the compound referring to “NOTE OF N : MIC
REPLACING IC2002 ON THE MOTHERBOARD a : BLUETOOTH
BOARD AND THE COMPLETE MOTHERBOARD
BOARD” on servicing notes (page 6). Note: Refer supplement-2 for schematic diagram of SMPS
and SMPS (EMC) boards.
Note 2: When the MS-476 board is defective, exchange
the entire LOADING COMPLETE ASSY (T).

Note 3: When the SENSOR board is defective, exchange

the SERVICE, TOP PANEL ASSY.

Note 4: W hen the complete MOTHERBOARD board

is replaced, be sure to refer to “DESTINATION
SETTING METHOD” on supplement-1.

MHC-V71/V71D
40 40
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.2

6-8. PRINTED WIRING BOARD - MOTHERBOARD Board - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


MOTHERBOARD BOARD MOTHERBOARD BOARD

J602

J601
TO
VIDEO OUT 

(COMPONENT SIDE) (CONDUCTOR SIDE)

SPEAKERS

A AUDIO/PARTY
CHAIN OUT
L L
AUDIO/PARTY
CHAIN IN
R R
 MHC-V71  FOR
SERVICE ONLY
 MHC-V71D HDMI OUT
(TV) ARC FM
ANTENNA
(CHASSIS)

CN2021 CN1000 8 7
4 3

C2090

C2150
21 22
JL2029
CN900

JL110
CN108
2 1
C2095 6 1

JL102
S A S

B C2151

JL111
20 23
1 19 JL900 JL620
C2084

JL101
(CHASSIS) JL901


R124
JL631 JL905

R2209
R1012
1T 2T 1T

L900
C1006
C1013 CL2052

C636
D900
C2079 L1001 L1002 R937 JL619 C1005 C638 CL2050 CL2048 CL2049 JL2030

C2202 R2207

C1010 C1009
2T C656 R1026

C2134
R101 R2211 R2206 C180 L601

C659
C658
JL1003 CL2051 CL2041

R126
R1019 C930

L901
R653

IC1000
R2212

2 3
4
C932

C628
CN2007 1

R756 C626

C2200

L605
R1020
C627
R1010R1011

R1022
R939
R752
R940 C1003

1
R1015
R1000 C629 CL2046

5
R1014
C931 C933

CL328
JL635

L902

C934
R700 R625 R753 12 1 1 C660 R1024 C1004

R1017
IC2200

R651
Q605
CL329 65 20

C665
CL2047

R2213
R2214
R2215
R2216
R624

R1023
21
C2203

X900
R692 C941
C2076

R944
25

4
5
IC902

R1027
16

C936
10
Q602 R685

R650
C917
Q607 13 CL2045

C181
11 15
Q303

8
C938

1
R2220 R686

JL2221
Q606 24 C2227

R689
R2225 R1025

R2226
JL604
R2219 JL618 IC1001

R2218
C943 R2221 R943 C1011

2
3

R946
R2227

C2228
RB303 R359

CL2040
JL605

1
4

R857
R641
IC903
C

Q603
Q302

R947
RB302
R368 R2208

C2133
RB305 FB610 R945 CL380

CL2044
R2203 C306 JL2026

28

27
RB304
R324

JL2222
C348

RB301

R309
C364
C620 R750 R628 C606 R627 R751 C347 C352

JL332

JL2021
96 65

C650
97 64

C647
C657
9
JL331

JL330
C346 R370

JL2020
C621 CL395
>001P C2068 R380 JL2035

CL2042
C351

CN2206
C652

C375

CL307
R915

R649 R916

CL2043
C359
C2067 R379 R319

8
C601 C766 R644 R642
C2060 C343
IC301

JL2223
R367

IC601

R912

R671

CL309
C372 C315
C2071 C2069

C767
CL308

R382
R365

7
R303 R302
9

2
>002P R321

C344
RB307
SMPS BOARD (EA, BR, AR, LA9,E12) / C2063 C2058 C2059 R914

R911
RB306

6
3

JL2200

JL355 C321
C643 3 1 C340 CL316
SMPS (EMC) BOARD (US, CND, AEP, UK, RU, MY, AUS, E4) R663 CL310

R381
R607

5
C341 JL2224 R669

4
129
R369 R600 C612 RB310 C339 R360

R662
R913
CN6500 EXTENSION BOARD C641

IC306
R615 C605 C338
IC303 4

CL313 CL311
C337 C342 R358

R648
JL2206 6
(Page 44) CN4500

C334
C2214 R339
RB308 R1008

R328
C360
C373 C369

C326
(Page 49) C358

C350
R608
C607
R330

10
R344
R345

8
R351

C328
R349
C616 JL2203

CL315
R634
R604 R602
R610
128 33 R616 C331

C631

C365
L301 JL362 C330

R352
32
R348 C325

JL358
R646 16
1
1

R325
JL359 C319
RB309

JL357
D

IC602
R327 C357

C363

R326


R356 R355

JL356
C602 R635 R657

R331
R334

R660

C336
L2003

JL361

R354
L2002

C316
R647
R332 C952C951

R605
R613

C954
C963
R664 R658
C307

C662
8

9
X301 C618

54

C634 C625
R640

C610

R638


C615
R342 FB321 FB320 C633 R639

R470
R472

R617
C308

R340

JL2012
JL2015
R652 JL603 X602

R811
R810
C322 C323 R800 C362 C635 R955

R779

R665
1
FL301 R609 R953 C950

C640

C648
IC603
2

7
R801
C608

R812

JL2005
C981

R614 C603

C726

48


R781
C663 C960

C985
R784 R618 R661

37
R654
3

6
IC302 8 5 R782
R619 (CHASSIS)

1
4

R674

36
C958

JL2018 JL2011
R981

JL2006
JL2016
C695
R622 R655


C604
16 9
R982

R983
R637

IC904
R690
R989 8 1

R804
IC610

JL056

R794
C2042 C2045 C2046 C614

C076
C2043 R987 R984

R620
R785
IC905

R656
JL2207 R985

C619
1 4

C632

JL2009
R677

C644
C613
C622 R986

R959
44 23 C2039 R988

24 25
9 16
C2038

R626

C642

R687

R783 R778

13
12
C646
R335 C630

C624
IC2002

1 8 14 8
R957

C609
R809 R807
R322

IC606

R803

9
R805

8
C356 C324 Q612 C617 C949

IC604
E C402

CL401
R814 C654 C645 R815
R378

C711
R808
R802
C2025

R329
C2036

4
IC305

C403
R2044 1 CL402 1 7

JL313
8

R402
1 22

28
1
CL408 R691

IC611
2 3
R806 C664

16
CL403

1
R2046 C353 C411 C649 C653 R688

CL404
C407 JL2003

R820

R401
R415

R408
R813 R951 R952
R450

CN302 C2032 C2027 R371 CL409

R950
1 23
R406

R632
C2024
C413 C987
R2042

JL2036

16

CL413
JL305
1
C420

R631
C655

R630

22
7
R422

C2028 R407 R411 R412

R2142 C2026

2 24

R435
CL405
CL2024
R434 IC401

C409 R418
7 6
R2152

R923
JL360 IC452
C468

IC453
8

TO LOADER DRIVE (CDM)

FL601

R451
R2034

JL307
10 1
R2118

29

30

R314
R2093
R2143

C466

JL311
4

R432
R431
Q401

JL2008
CL414
R2031
C073
C421 R421

R453
SERVICE, OPTICAL DEVICE (7G) Q304

R389

C423

JL303
JL308 JL309
6 4
FB013 C404 C465
R424

R313

21
8

Q305
CN451 CN451 CL410

JL321
3
C071

FB455

JL315
C2020 C2010

JL319
C467

JL317
JL314
C463
R498
C302 Q007 6

6
R409 JL462

JL316
JL310

JL306
JL302
JL363 C2019
1

1
56 29
C2135 CL412 R318
CN302

CL415
1 23 CL411 C462 R310
>003P

CL2025
R478
C2009

C408

15

JL463
14
JL304

R404
R039

2 24

JL322
R2020 JL2038

JL323
R2010
IC2001
F JL050

R448
R446
R447
JL461

Q402
JL320
C2014 MIC USB BOARD JL460 R2022
CN303

D401
D402
C366

C406
C405
R410 CL2021
(CHASSIS)
Q006

C2013
5

5
1 28 R323 CN4101
7

7
1

C303

JL329
CL2035

C311

C424
R2019 R040 C418 R449 JL401 R2021 CL2020 JL2040 JL2037
2

JL301
(Page 46)

R316
C419
C2007

C2015

JL318
JL324
C2008 C2021 R301 CL2036 JL2034

C067

JL326

R429
C367
JL328

JL312
C066
JL023 CL2023
4

R030
CN402 CL2022
5


R221
R224
R226
R2011


R2096

JL406 JL402 JL2039

D1001
4 1

JL405
R2003
D103

R529
Q005
R219
JL2042
R2009

R211 R520

R148
C2012 C143 C064 R534
JL022
R2004

6 5
C2108
R526

Q1001
R034

JL130
JL2041
CN303

R1002
R232

C141 C142 R1001 R230

R229

JL327
R1006

JL325
Q459
Q457

JL294
R1007
R205 C139

R528
Q1002
R028

R174
Q1000
R535 R037

JL070
1

R150 R242

C1001
JL138
IC2000

R527
2

JL136

C1000
R1003
C2006

MS-476 BOARD R530

R251
R517

Q1005
R2023
R2006
R2007
R2008

R1005
R257 JL143 R1004 R273
R295

R213

JL021 JL146 JL024 R514

R218

R271
R164
R181

R215
JL145 JL209
4

R193
R201

R171 Q111

R512
FB107
FB108
R141 R254
5

1 JL149
JL212 FB109 C146 C501

1
R261 JL144 R513
R299

C137 C133

R091

C2000
2

2
1 JL142 R119 R237 C135

C503
C140
R270

FB106

C148
JL525
RB106
44
R222
R247
R519

R533
C2004 45 176
R272 C095 R259

C111
Q110 JL137 R274

R524
C2003
C103

R197
R180

JL524 C164 R300

G TO FAN 1 C153

R515
R117

R097 IC003
R168 R255

4
R099 R289
IC002
3

R170
R284
C502
C506

C168
R173 R292

C154 R293
C104 C102

R120
1
R094
R288

8
R115

R282

R129
R169

R143
R506

C008
4
R234 JL147 C507

C112
C065 R187
R291 R290
IC106

RB104
JL528
JL269
C518

CN2001 R516

CL2026
C097

1
R172
Q107

R116 C106
C523

JL287
R510 C087 JL230
14 8

C155
R103 R522

R107
R2153

5
R128

R2205

RB105
3 4 C109 JL002

C114
R511 R208

R140
IC109 IC102

JL527
R151

JL526
C504
D102

C298

R507
R521 C012

R139
R127 JL231
JL295

14

C115 JL150

14
C126
C2209 >004P C156
1 2
JL139

C157
1 R102

R137
R188

JL194
15

R263

C107 JL232
Q2002

15
R285

1 7

JL529
C110 X105 R2146
R186

2
C127

JL141
IC2003
R508

R235

C2116
R505 C280 R149
16

C297

16

C158
17
C105

JL530
17
C281 R104
R2040 R2039
R2037 R2036

R2026 3 4
SENSOR BOARD JL521
C151

R2035 FB104

C118

C2127
18

R184
IC103

18
FB105
JL296

R177
19

CN5401
X104

R131
R135 R283
R134 C283
R123

19
R275

R175
JL520

JL148
C2022 R178
C2017

R160

R176
R2076 RB108 FB102 (Page 43) JL523 C117

C159
RB109 JL522 C160 C2128
C2023

CL2011
TH571
FB103
R487

C282

JL2031
R538

C2018 FB101 R158

R577

C2136 Q572 R276 C120 R249

R532
CN126

R539

CN126
JL140
R2015 R2013

C577 C152 R256 RB101 C122

C573 R485

R298
C2115

R278
C129

R152
H
C3503

C131
C128

133
R2084 88 R267 JL124
R2024

JL123

JL155
R2014

89

CL2010
CL2004
Q2000

R145
C144 C138

JL119
D2001
R190
C150

C116 R531 R264 JL107 JL115 C147 C136 C134

28
Q575

C162

132

28
JL122

JL151
R196 R280
29

29
Q574 RB107 JL135 JL121
C161

R2025 R225 JL289

D571

JL154
Q571 CN120 JL120 R518
R509

D2002 R195 JL109

R228
R200

R572 C299
C149

R483
R491

R198

R543
C2016 JL152 R546
R236

R122
R223

R203
7

R049
R132

R571 R113 X103 JL106 R050

R111

R220
R227

D572 JL132 R106

R233

6
Q576

Q2005

R544
R545
C574 JL134
C132

C130 (CHASSIS) JL118 JL116 C061

R2087
>005P
JL153 IC010 R046
R023
C055

Q2006 JL297 JL117

R166

R192
R238

JL2033
C037

C039
D2000

6
R2085

C030 C003 JL131 4

R027
JL055
R114
R087
C054

JL105
IR BOARD
R024

JL069
R548
R549 R550
R121
R130

C005 3
1

R3009
CN902 1 R045
8
9

IC001

R189

C675 JL227
2 4 6 8 CN4200 C060 CL2038

R917 C670 R711

R241
R547

C3004

(Page 49) R709

17
L006

R025
L001

R012

R3014
C053

C669
R3019

1 5 7 9 JL176
R719
C015
16

CN127

JL195
R722
C052 R3015 JL044

C667
JL617
1

L009 C013 Q011 R068

R540

C017 JL175

CL3003
5

I
C026

JL059
3

R708 JL174 CL2039

C167
IC609
7

14 8

JL197
JL235
L008 JL172 JL008
6

JL173
JL169

VSSAMARA09 - 7/18/2022 5:25 AM

R3022
>007P

JL199
JL125 C666

JL205
R720 R723
JL108

JL215
JL001
1

R191
4

R086 R001 L003 1 1 7 JL171 R064

C672
12

C3019

R065
4

R018
R3016 R053
R716
R998

R066
JL201
JL206
SENSOR BOARD
10

IC3000
9
C006 C041 R3021 C673 JL012
>006P C678 C062

JL196
5 8 2 1 R015
1

JL200

JL198
JL203
CN5301 JL204

JL202
C038 JL601 C032
IC009

JL071
C004 Q009
R3020

3 4 C674 R069

JL068
6 4
C024

C040 Q104 (Page 43)

C3001

CN120
IC3001

JL216
C671
MIC USB BOARD R013 C047 CN902

C3018
C986

JL615
C3000 Q012

R031
R051
MICROPHONE, JL910
C050

R026

JL004
3

2 4 6 8
CN001

JL072
1 3
CN4103

R020
8

R3032
9

JL217
R061
ELECTRET
1

JL114 R019 JL045

(Page 46) R109
IC007
L002

L007

VR3001 CL3058

CL3059
1 5 7 9
R3029
17

CL3062

CAP CL3006
2

R792
R062

Q103

Q461
R014

R032

CL3001 R3049 JL614

R3040
R3028
R108

JL908
JL909
4

C3006 R3043 C031 JL046

C029
16

C014 Q008 CN3001

R3046
1

C016 C049 C3005 JL113

JL049
JL616
FB601 FB603

CL3008

R033
R3044
FB602

R3048
R3045
C091
C092

JL613
C019

Q004
CL3002

R035
R3041
C083

R3004
CP3000

C028 R3018 1 13
R029

R060
C084

R3047
C068 JL048
J R088
14
2 12
15

R3005 JL073 2 1

R070
2 1 2 1
R3030 C078
L004

R077 CL3009
>008P R3039 R3003

C080
CN3007
11

C085 R3042 JL047 C079 C051

1

JL011
C011
C010

C072

SMPS BOARD (EA, BR, AR, LA9,E12) /

C093

SMPS (EMC) BOARD (US, CND, AEP, UK, RU, MY, AUS, E4) IC006 IC004 IC008 JL005
TO BM64 MODULE
C096

NO6501 JL053
C057

C048 3 3 3
(Page 44)
JL057

(CHASSIS)
K
(CHASSIS)
31 31
1-983-189- (31) 1-983-189- (31)

Note 1: When the MOTHERBOARD board is replaced, spread the compound referring to “NOTE Note 2: When the MS-476 board is defective, exchange the Note 3: W hen the complete MOTHERBOARD board
OF REPLACING IC2002 ON THE MOTHERBOARD BOARD AND THE COMPLETE entire LOADING COMPLETE ASSY (T). is replaced, be sure to refer to “DESTINATION
MOTHERBOARD BOARD” on servicing notes (page 6). SETTING METHOD” on supplement-1.
MHC-V71/V71D
41 41
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

6-9. PRINTED WIRING BOARD - SENSOR Board (Component Side) - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

SENSOR BOARD
A (COMPONENT SIDE)

D5005

B JL5224
JL5207 JL5200 JL5201 JL5208 JL5221
- PARTY CHAIN FIESTA VOICE GUITAR
PARTY LIGHT CHANGER

D5001 D5000

C CL5329

JL5225 JL5222
JL5203
WIRELESS PARTY CHAIN MIC VOCAL
ECHO FADER

D5200

JL5205 JL5220 JL5227

E MEGA BASS
MIC/GUITAR LEVEL - MIC/GUITAR LEVEL +

D5008
D5002

CL5328

CL5327
JL5217
JL5223 JL5226
-
+
G

CL5325
D5003

JL5204 - PAIRING JL5229 JL5206 JL5218 JL5228

H BLUETOOTH
GESTURE SOUND VOLUME - VOLUME +
ON/OFF FIELD

I
JL5210 JL5212 JL5216
PLAYBACK DJ JL5213 KARAOKE
SAMPLER
JL5202 JL5219
F U N C TI O N

J

D5006 JL5209 JL5211 JL5214 JL5215 D5007

N TUNING -
x TUNING +
.
>
K
11
1-982-748- (11)

Note: When the SENSOR board is defective, exchange the

SERVICE, TOP PANEL ASSY.
MHC-V71/V71D
42 42
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

6-10. PRINTED WIRING BOARD - SENSOR Board (Conductor Side) - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

SENSOR BOARD
A (CONDUCTOR SIDE) VFD BOARD
CN4000
(Page 46)

>009P

C5033 C5026
C5024

CL5057
R5024 R5036

C5027
R5027
CL5059 C5025 C5028
CL5079

R5035
R5034
R5033
R5032
C5030 C5029

R5031
CL5080
CL5427 7 1 C5031 R5030
CL5415
B

CL5431

CL5416
R5029

CL5418
6 2
CL5432 CL5428 CL5078 CL5058 24 13

CN5402 R5028

C5039
R5050
R5052
R5057
R5051
R5056
R5055
R5054
25
C5036
IC5001
CL5433 CL5082 R5058
CL5403
CL5429 C5037
1 12

R5053
CL5430 R5025

R5400
R5401
R5026 C5038
R5101 CL5048 C5047 C5040
CL5401 CL5400

R5059 C5035
R5060 C5034

C5046
C5045
C5044
C5043
C5042
C5041
C C5407

CL5063
CL5066
CL5069
CL5083
CL5084
CL5444

CL5405 CL5060

CL5068
R5406 CL5065
CL5441 CL5422

R5407

CL5149
CL5062
1

CL5423
CL5426
2

2
CL5424 CL5425

CL5411
CL5443 CL5148

D CL5442
CN5401

CN5401
CL5404 D5307
JL5300

CL5412

R5200
CL5413
R5403 CL5410 CL5409
>004P

CN5301

C5217
D5306 C5320
CL5419 CL5408 D5305 JL5302
MOTHERBOARD BOARD CL5417 JL5303

D5301
JL5314
JL5313
CN126 R5405 JL5305
(Page 41)
JL5306

C5412

1
JL5318 JL5308

2
JL5309

JL5311
CL5445

JL5316
C5410

6
JL5312

7
E
28

28
R5313 JL5319
29

29

R5320 R5316

R5317
D5308

D5310
CL5407 CL5406 R5318

D5304
R5404
R5321 R5322 R5319 JL5320
R5408 C5305 C5309 C5304 R5327 R5332 R5315 C5318

R5347
CL5316 CL5314 CL5319 CL5320 CL5322 CL5323 CL5312 1
C5405
C5408
CN5301 CL5318 14 R5329
IC5300

R5348 JL5317 JL5315

D5302
1

CL5313

C5316
15 28
2

>007P CL5324 C5315 D5311

F MOTHERBOARD BOARD
6

D5303
CL5326
7

C5300
CN120 D5309
(Page 41)

C5306
C5311

R5328
R5330
R5324
R5314

R5325
CL5321 CL5317 CL5315 D5300
C5303 C5308

R5323

R5207
R5201
R5202
R5203
R5204
R5214 R5205
R5206
R5209
R5239 R5243

C5213

R5063 R5062
R5073 C5057

R5091 C5050
R5211IC5200
R5402

C5214
CN5400

CL5402 R5208
R5238
R5235
R5233

CN5400
G CL5202 C5052 R5210

C5201
C5200
18 13
C5212
19 12 R5212

R5064
R5072
R5071
R5070
R5089
R5069
R5068
25
>010P
6

R5229
5

C5215 1 R5230 R5228 24 7 CL5200

R5213
2

2
1

1 6
NFC BOARD CL5203 7
6 24
CL5111 CL5110 R5215 C5203
R5244

CN001 R5245 25 IC5201 C5211 R5227 CL5201

C5202

C5207
R5219
12 19 R5231

R5220
R5221
R5222
(Page 49) R5246
R5226

R5216
C5210

C5206
R5217
13 18
R5247

VSSAMARA09 - 7/18/2022 5:25 AM R5232

R5242
R5241
R5240
R5237
R5236
R5234

C5048
C5049
R5061

CL5112 C5051
C5053
C5054

H
R5066 R5065 C5055
CL5137
R5102

24 IC500213
R5067

25 C5064
C5060 R5218
C5065
R5077 C5070
C5058 CL5101

12 C5069
1 R5074 R5078 C5066
C5061 R5079 C5067
R5084

R5080
C5059

C5068
R5076
R5081
R5075
C5071
C5062
C5063

I CL5136 CL5135
R5083 CL5134
R5082
CL5147

CN5001 CN5001
CL5123

J
17

17

R5096
R5095

CL5150
16

16

CL5118CL5122

CL5121 CL5120
CL5119 R5094
R5093

CN5403
>011P CL5117 CL5115
5 1
HUB BOARD (US, CND, AEP, UK, RU, MY, AUS, E4) / CL5116
CL5146

4 2
HUB //NON-EMC BOARD (EA, BR, AR, LA9, E12) R5098
CN4300 CL5440
CL5114

(Page 45)
2

CN5403
Q5008 R5097
1

1
R5099

CL5113 CL5439 5 1
R5100
K 4 2

Q5009 CL5434 >012P

POWER KEY BOARD
11
CN4220
(Page 49)
1-982-748- (11)

Note: When the SENSOR board is defective, exchange the

SERVICE, TOP PANEL ASSY.
MHC-V71/V71D
43 43
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.2

6-11. PRINTED WIRING BOARD - SMPS Board (EA, BR, AR, LA9, E12), SMPS (EMC) Board (US, CND, AEP, UK, RU, MY, AUS, E4) - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11 12 13

SMPS BOARD (EA, BR, AR, LA9, E12) /

SMPS (EMC) BOARD (US, CND, AEP, UK, RU, MY, AUS, E4)
MOTHERBOARD BOARD
CN2007
A (Page 41)
 SMPS
 SMPS (EMC)
>001P

R6523
JL6532

JL6513
JW6014 9 1

JW6028 R6521 R6536

JW6010 R6548 CN6500
B JW6018
R6535
(CHASSIS) (CHASSIS)
ET6000 R6547 ET6500

JL6518 JL6519
Q6501

R6539
C6506

JL6511
D6000 C6301 JL6531 R6561

C6322

JL6515

R6555
R6549 JL6533

FB6501
JL6520
C6321 R6538 R6559 JW6011 
1 R6560 
R6550 JL6510
Q6504 JW6021
C JS6302 T6300
CONVERTER
JS6501

R6558
JL6514
JW6009 TRANSFORMER 2 NO6501

C6515
JL6503
R6322 R6557
JS6000

TH6000

1
NO6501
JL6516
JL6541
JW6002 JS6009

D6504
D6001 R6326
C6505 JL6506

3
MOTHERBOARD BOARD
CN001
C6314 (Page 41)

JS6503
 

C6507
C6529
>008P

C6500

C6523
D6307
D
R6318
R6300

JL6542
JS6008
JS6006

JS6001
JS6003

JW6030
JW6013
 C6320

JW6007

JS6504
LF6000

R6305

D6501 F6500

JL6512
R6319
R6301

11

11
JW6020

JL6504
C6003

JL6517
JL6507

JS6500
FB6300
R6302

Q6300
R6303
JL6302

C6006 JL6509
C6000 R6309 C6303
C6534

C6501

JW6023
JW6008

JW6022

FB6502
E JL6301

JW6026
R6306

JW6006
JS6300

FB6301 Q6301
C6310

Q6303

JS6005 C6524 R6554 

JW6027
JS6002
JL6002

R6335
LF6001 C6311 JW6029
JL6508
JL6304
R6316

JL6536
CN6000

JW6017 JR6005

JL6534
JS6301
JL6309

R6556
D6502 JL6526
R6315

R6504
JW6019

JR
JS6505
Q6302
JL6538

JW6005
R6312
JL6303

JS6010
1

D6312
JS6007

R6505
3

JW6012
JL6535
R6307

JS6004
R6333

F R6340 TH6300 R6525

R6517 C6510 R6520

~ AC IN
R6310

R6330

D6340 R6334 D6313 JL6528

Q6305

D6311 C6319 D6503

R6502
JR6004
VR6000 JW6003
JW6016

R6516 R6515 R6514

1

C6504
C6307

C6509
IC6500 JL6522R6509
PH6301

R6507

C6511
R6508
JL6305

JL6521
2

5 8 JL6524
R6321

JL6523
Q6304 JR
JL6001

D6505 D6509
C6317

JW6025 R6336 JL6530

R6339
D6308

JL6308
Q6307 JW6024

2 1
D6500 R6537
R6323 R6328

D6510
JW6015 JW6004

IC6300
JW6000

C6007 C6300 C6313 D6306 PH6302 R6545

4 1 3 4
R6551 R6546
JL6307

JL6000 R6341 D6515

R6501
C6312

D6511

ET6501
C6340 D6300 JL6529

R6518
R6542 JL6525
JW6001C6315

C6502
G F6000 D6341 D6516 R6543 Q6506
PH6300 C6522
R6320

R6540
R6327

R6313
R6500
(CHASSIS)
JL6500 Q6500 R6544

C6521
R6541
R6503

R6512
D6303
C6305

C6309

R6338

Q6507

JL6527
JL6306
JL6300

H 12
1-982-604- (12)

MHC-V71/V71D
44 44
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

6-12. PRINTED WIRING BOARD - HUB Board (US, CND, AEP, UK, RU, MY, AUS, E4), HUB //NON-EMC Board (EA, BR, AR, LA9, E12) - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

HUB BOARD (US, CND, AEP, UK, RU, MY, AUS, E4) /
A HUB //NON-EMC BOARD (EA, BR, AR, LA9, E12)

C4336
CL4353

JR4314
JR4324

JR4318
CL4323
R4327 R4334

CL4322

C4335
R4306

JR4312
CL4338
CL4312 R4328 R4335
B

CL4324

CL4325

JR4319

JR4305
CL4337 CL4348

JR4300
CL4302 CL4339
R4329 R4336

JR4315
JR4308 CL4335

JR4316
9 R4309 R4316
7 R4326 R4337

CL4355

7
CL4304 C4339 CL4349
CL4340

JR4322
CL4308 C4340 R4310 R4317 CL4336
JR4313 R4324 R4338

1
13 12

JR4302
CL4306 CL4341
CL4330 CL4350

JR4306
R4311 R4318 R4325 R4339

IC4300
CL4300 CL4342

CN4302
CN4300

CN4303
2 16
R4312 R4319 CL4331 25

JR4329
CL4307 CL4343 C4326
C JR4307
1 17
R4313 R4320 CL4332
CL4344 C4327 CL4351
R4314 R4321 CL4333 24 1 CL4345

6
JR4680 C4315 JR4325 CL4352

R4331
CL4346

CL4327
>013P C4341 CL4347 >014P

R4308 CL4328
1

CL4354
8

CL4326
JR4309 JR4320

JR4310

8
360 FR R BOARD CL4321 JR4304 JR4317 R4357 CL4334 CL4303 R4332 360 FR L BOARD
CN4480 C4314 CN4470

CL4329
C4305
(Page 48) JR4321 JR4301 (Page 48)
CL4309 C4304 CL4305
CL4310 C4316 R4333 JR4326
R4358 R4322

JR4303
CL4311

R4307
C4312
JR4311

CL4301
JR4328

VSSAMARA09 - 7/18/2022 5:25 AM

JR4327
R4354

>011P

R4356
SENSOR BOARD
CN5001 R4348
(Page 43) R4350 R4352
E
4 1

CN4301 6 5
SPK MID L BOARD
CN4401
(Page 50)
>016P
SPK MID R BOARD
CN4411
(Page 50)
11
>015P
1-982-749- (11)
F

MHC-V71/V71D
45 45
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

6-13. PRINTED WIRING BOARD - MIC USB Board - 6-14. PRINTED WIRING BOARD - VFD Board -
• See page 32 for Circuit Boards Location. • : Uses unleaded solder. • See page 32 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 1 2 3 4 5 6

MIC USB BOARD VFD BOARD

A A
SENSOR BOARD
CN5402
MOTHERBOARD BOARD MOTHERBOARD BOARD (Page 43)
CN451 CN902
(Page 41) (Page 41) >009P
>003P >006P
CL4021 CL4002
B CL4113 B C4012 CL4004

JR4003
7 1
CL4030

C4005
JR
CL4024 CL4006

JR4102
R4106 C4011

JR4000
JR JR4107

R4012
R4011
2 8 6 2
CL4121

JR4108

JR
JR4103

JR
1 9

R4001
CL4116

R4000
JR CN4000

R4017
JR4104 CL4110 CN4103 JR4110 CL4028

JR
CL4112
JR

R4113
C4129 JR CL4026 C4010 C4015
JR

CL4127
CL4111 JR4109 CL4032 CL4008 CL4007 CL4005
R4130 R4131

CL4117
C4112 R4009 C4006 CL4025 CL4010

R4144
R4112 C4127 R4110 C4116 CL4035 CL4029 CL4013
R4007 CL4023 C4000 CL4003

C4120
R4109 C4114 C4128 JR

R4143
C4119
6 3 1 CN4101 R4008 CL4027 CL4022 CL4001 CL4011JR4004
CL4118

C4124 CL4031 CL4017

C4003
C C4117 R4123
C

1
CL4105 C4105 C4123 R4002
R4102 R4121 CL4034

JR4106
R4134
C4121 C4118

R4122 C4130

JR
CL4109 CL4107

R4138
CL4119
IC4100

1 8
C4122 R4133 CL4033 C4014 CL4020 CL4018

3
CL4104 C4132 Q4109 CL4012
C4131 C4013 R4003

D4000
CL4126 R4108 Q4107
IC4000

2
CL4019
R4127

4 5
CL4108 CL4009
CL4123 CL4122 Q4108
C4101 ND4000

JR4001
CL4124 R4135 CL4125

R4005
C4007
C4008
C4009
R4004
R4006

JR
C4134

JR4002
R4140

R4141

R4137 CL4130 CL4132

CL4131

JR4105 CL4114 Q4110

C4133

JR
R4139
C4102

C4126
D4102

JR
J4100 J4101
D D
D4100
CL4100

C4103
CL4115
D4101

JR4100

CL4106
CL4129

C4104 FB4101
JR

FB4100
C4110

D4103 CN4100
D4108

C4136
C4135

D4109

4 1 C4109
7
6
5
C4107
CL4128

W4100
CL4102
E E

REC/PLAY 5V 1A MIC1 MIC2

GUITAR

F F
11 11
(11) 1-982-745- (11)
1-982-746-

MHC-V71/V71D
46 46
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

6-15. PRINTED WIRING BOARD - 360 BACK L Board - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11

360 BACK L BOARD

A

CL4463
CL4465 CN4460

JR4460
CL4462
D4460 D4461 D4462
6 5

R4468

R4461
B 4 1

JR4461
CL4460
R4467
CL4461

>017P
EXTENSION BOARD
C CN4501

11
(Page 49)

1-982-752- (11)

6-16. PRINTED WIRING BOARD - 360 BACK R Board - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11

360 BACK R BOARD

A
VSSAMARA09 - 7/18/2022 5:25 AM CL4492
CL4493
CL4491

R4498
CN4490
R4491

1 4

CL4495

B D4490 D4491 D4492 JR4401

5 6

R4497
CL4490
>018P
EXTENSION BOARD
CN4502
(Page 49)

C 11
1-982-909- (11)

MHC-V71/V71D
47 47
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

6-17. PRINTED WIRING BOARD - 360 FR L Board - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

360 FR L BOARD
A

R4477
R4471
CL4476

8
CL4474

6
CL4473

JR4475
JR4472 JR4485
D4470 D4471 D4472 CN4470
JR4486 CL4472
R4472

JR4474
JR4471 CL4471

B 1 4
JR4473

CL4470
JR4470

JR4476
CN4471 CL4477
5 6

7
C >019P >014P
SW LED L BOARD HUB BOARD (US, CND, AEP, UK, RU, MY, AUS, E4) /
CN4440 HUB //NON-EMC BOARD (EA, BR, AR, LA9, E12)
(Page 50) CN4303
(Page 45)

11
D
1-982-753- (11)

6-18. PRINTED WIRING BOARD - 360 FR R Board - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

360 FR R BOARD
A
8

R4484
1

CL4480
CL4481
CN4480 D4482 D4481 D4480
R4481

R4489
CL4483
CL4482

B
JR4480

CL4486 1 4
JR4481

CN4481
5 6
CL4485
CL4484
7
9

C >013P >020P
HUB BOARD (US, CND, AEP, UK, RU, MY, AUS, E4) / SW LED R BOARD
HUB //NON-EMC BOARD (EA, BR, AR, LA9, E12) CN4450
CN4302 (Page 50)
(Page 45)

11
D
1-982-754- (11)

MHC-V71/V71D
48 48
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

6-19. PRINTED WIRING BOARD - POWER KEY Board - 6-21. PRINTED WIRING BOARD - NFC Board -
• See page 32 for Circuit Boards Location. • : Uses unleaded solder. • See page 32 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 6 1 2 3 4

POWER KEY BOARD NFC BOARD

A A (COMPONENT SIDE)
SENSOR BOARD SENSOR BOARD
CN5403 CN5400
(Page 43) (Page 43)
>012P >010P
C001 CN001
IC001 1 9 8 6 8
C003 4
5 1 7

C002
R001 R002

B 5 1
B
VSSAMARA09 - 7/18/2022 5:25 AM
4 2
11
CN4220 CL4222
1-980-619- (11)
CL4221
NFC BOARD
CL4220
S4220 S4221
TAIKO 1 (CONDUCTOR SIDE)
C C

11
1-982-849- (11)
11
D D 1-980-619- (11)

6-20. PRINTED WIRING BOARD - EXTENSION Board - 6-22. PRINTED WIRING BOARD - IR Board -
• See page 32 for Circuit Boards Location. • : Uses unleaded solder. • See page 32 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 1 2 3

EXTENSION BOARD IR BOARD

A A
360 BACK R BOARD 360 BACK L BOARD MOTHERBOARD BOARD
CN4490 CN4460 CN127
(Page 47) (Page 47) (Page 41)

>018P >017P >005P

CN4502 CN4501

B 6 4 1 5
B
1 4
CN4200

CL4202
CN4500 R4200
IC4200
5
4

CL4200
1

CL4201
R4201

C4201
5 6
9 10

CL4203
1 8
JR4200 4

CL4204
C C 11
1-982-747- (11)
>002P
MOTHERBOARD BOARD
CN2206
(Page 41)
11
D 1-983-297- (11) D

MHC-V71/V71D
49 49
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

6-23. PRINTED WIRING BOARD - SPK MID L Board - 6-25. PRINTED WIRING BOARD - SW LED L Board -
• See page 32 for Circuit Boards Location. • : Uses unleaded solder. • See page 32 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 1 2 3 4 5

SPK MID L BOARD SW LED L BOARD

A A
R4440

D4440
R4400
CL4404 R4401 CL4443
CL4401
D4400
CN4440

6
4
B CN4401
B

R4441
1 3
CL4400

1
4 5

5
>019P
CL4440 360 FR L BOARD
CN4471
(Page 48)

>016P

D4442
HUB BOARD (US, CND, AEP, UK, RU, MY, AUS, E4) /

C 11 C
HUB //NON-EMC BOARD (EA, BR, AR, LA9, E12)
CN4301
(Page 45) 11
1-982-755- (11) (11)
1-982-750-

6-24. PRINTED WIRING BOARD - SPK MID R Board - 6-26. PRINTED WIRING BOARD - SW LED R Board -
• See page 32 for Circuit Boards Location. • : Uses unleaded solder. • See page 32 for Circuit Boards Location. • : Uses unleaded solder.

1 2 3 4 5 1 2 3 4 5

SPK MID R BOARD SW LED R BOARD

A A
HUB BOARD (US, CND, AEP, UK, RU, MY, AUS, E4) /

D4452
HUB //NON-EMC BOARD (EA, BR, AR, LA9, E12)

CL4450
CN4301
(Page 45)
>015P
R4451

CN4411

5
B B

1
CL4411 4 3

2 1

4
D4410

CN4450
6
>020P
CL4412 CL4453
R4410 R4411 360 FR R BOARD
CN4481

R4450
(Page 48)

D4450
CL4410

C C 11
1-982-751- (11)

11
1-982-756- (11)

MHC-V71/V71D
50 50
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
SECTION 7 Ver. 1.2
EXPLODED VIEWS
Note: The components identified by mark 0
• The mechanical parts with no reference • -XX and -X mean standardized parts, so or dotted line with mark 0 are critical for
number in the exploded views are not sup- they may have some difference from the safety.
plied. original one. Replace only with part number specified.
• Items marked “*” are not stocked since • Accessories are given in the last of this
Les composants identifiés par une marque
they are seldom required for routine parts list.
0 sont critiques pour la sécurité.
service. • Color Indication of Appearance Parts Ex-
Ne les remplacer que par une pièce portant
Some delay should be anticipated ample:
le numéro spécifié.
when ordering these items. KNOB, BALANCE (WHITE) . . . (RED)
↑ ↑
Parts Color Cabinet’s Color The components identified by mark 9 con-
tain confidential information.
Strictly follow the instructions whenever the
components are repaired and/or replaced.
Les composants identifiés par la marque
9 contiennent des informations confidenti-
elles.
Suivre scrupuleusement les instructions
chaque fois qu’un composant est remplacé
et / ou réparé.
7-1. SIDE PANEL SECTION
1
2

rear cover section

VSSAMARA09 - 7/18/2022 5:25 AM

3
loading panel section 1

Ref. No. Part No. Description Remark

1 4-591-404-01 SCREW, TAPPING (FLAT HEAD)
2 4-729-055-01 PANEL, SIDE L
3 4-729-056-01 PANEL, SIDE R

51
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.2

7-2. LOADING PANEL, REAR COVER SECTION

top panel section

55

#2

53 54
#1

ns #2
#2

56
52 back panel
section

57

51

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 X-2595-667-2 PANEL, LOADING ASSY 56 4-532-593-02 SCREW (4X13) (TR-184A)
52 4-591-404-01 SCREW, TAPPING (FLAT HEAD) 57 4-729-065-01 COVER, REAR
53 4-591-404-01 SCREW, TAPPING (FLAT HEAD) #1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
54 4-733-262-01 COVER, SCREW R #2 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
55 4-733-263-01 COVER, SCREW L ns not supplied

52
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

7-3. BACK PANEL SECTION

#4

CDM section

SMPS board section

VSSAMARA09 - 7/18/2022 5:25 AM

MOTHERBOARD
board section

ns

103
#2 #2
102

ns
ns
#2
#2
#2 #3
(V71D)
#2

101

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
101 4-735-267-01 COVER, JACK (V71D) #3 7-682-547-04 SCREW +B 3X6 (V71D)
101 4-735-267-11 COVER, JACK (V71) #4 7-685-648-71 SCREW +BVTP 3X12 TYPE2 IT-3
102 4-735-291-01 COVER, VENTILATION ns not supplied
103 4-731-228-11 COVER, SERVICE
#2 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3

53
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.2

7-4. MOTHERBOARD BOARD SECTION

#1
153 ns

ns

ns

#1
152
ns

151

#1

chassis section

Note 1: When the MOTHERBOARD board is replaced,

spread the compound referring to “NOTE OF
REPLACING IC2002 ON THE MOTHERBOARD
BOARD AND THE COMPLETE MOTHER-
BOARD BOARD” on servicing notes (page 6).

Note 2: When the complete MOTHERBOARD board

is replaced, be sure to refer to “DESTINATION
SETTING METHOD” on supplement-1.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
9 151 A-2197-390-A MOTHERBOARD BOARD, COMPLETE 152 2-677-839-01 +PWH 3X8 (SUMITITE)
(for SERVICE) (V71) 0 153 1-855-006-41 FAN, DC
9 151 A-2197-394-A MOTHERBOARD BOARD, COMPLETE
(for SERVICE) (EA, BR, AR, LA9, E12) #1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
9 151 A-2197-395-A MOTHERBOARD BOARD, COMPLETE ns not supplied
(for SERVICE) (AEP, UK, RU, MY, AUS, E4)

54
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

7-5. SMPS BOARD, CHASSIS SECTION

ns

ns 202
(US, CND, AEP, UK, RU, ns ns
MY, AUS, E4)
204
ns
ns
205
ns
204
front panel section
ns ns
ns
203
ns
ns
ns
ns #1
ns ns
#1
ns 207 206
ns
ns
ns
(US, CND, AEP, UK, RU,
MY, AUS, E4)

speaker cabinet section

ns
ns 201

207

206

bottom cover section

208
VSSAMARA09 - 7/18/2022 5:25 AM

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
201 1-457-369-12 CORE, FERRITE 205 4-558-595-01 STEP SCREW M4
(US, CND, AEP, UK, RU, MY, AUS, E4) 206 4-558-820-11 + FLAT TAPPING SCREW - ED BK
202 2-677-839-01 +PWH 3X8 (SUMITITE) 207 4-729-076-01 SOUND GENERATOR 12CM
0 203 A-2203-517-A SMPS BOARD, COMPLETE 208 4-532-593-02 SCREW (4X13) (TR-184A)
(EA, BR, AR, LA9, E12) #1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
0 203 A-2203-518-A SMPS (EMC) BOARD, COMPLETE
(US, CND, AEP, UK, RU, MY, AUS, E4) ns not supplied
* 204 1-500-082-11 CLAMP, SLEEVE FERRITE
(US, CND, AEP, UK, RU, MY, AUS, E4)

55
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

7-6. FRONT PANEL SECTION

ns
ns
262 #6

SP4
ns ns
#6

259 #1 SP2
#1 ns
264

260 252 ns ns
#5
251

#1
ns

ns

ns ns
ns
A
253 ns

#1 ns
ns ns ns
ns
#1 254 #6 ns

#6
B
ns
257
A

#1
#1

261
ns 258
255
B
#1
#6
263
ns
ns
#6
261 263

#1 256 263

Note: If flexible flat cable is replaced, install it after bending

it in the same form as that before replacement.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
251 A-2192-334-A IR BOARD, COMPLETE 260 1-912-628-12 FLEXIBLE FLAT CABLE (17 CORE)
252 A-2197-353-A HUB BOARD, COMPLETE 261 1-912-630-12 FLEXIBLE FLAT CABLE (4 CORE)
(US, CND, AEP, UK, RU, MY, AUS, E4) 262 X-2595-665-3 PANEL, FRONT ASSY (VANILLA)
252 A-2216-749-A HUB //NON-EMC BOARD, COMPLETE 263 4-578-508-01 FOOT
(EA, BR, AR, LA9, E12) 264 4-912-253-01 CATCHER
253 A-2192-344-A SPK MID R BOARD, COMPLETE
254 A-2192-345-A SPK MID L BOARD, COMPLETE SP2 1-859-269-11 LOUDSPEAKER (5CM) (Tweeter) (L-CH)
SP4 1-859-269-11 LOUDSPEAKER (5CM) (Tweeter) (R-CH)
255 A-2192-341-A 360 FR R BOARD, COMPLETE #1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
256 A-2192-340-A 360 FR L BOARD, COMPLETE #5 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3
257 A-2192-347-A SW LED R BOARD, COMPLETE #6 7-685-647-71 SCREW +BVTP 3X10 TYPE2 IT-3
258 A-2192-346-A SW LED L BOARD, COMPLETE
259 1-852-158-21 MICROPHONE, ELECTRET CAP ns not supplied
56
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

7-7. BOTTOM COVER SECTION

ns

ns
ns 303

ns

ns
ns
ns

301
ns

304 ns
ns ns
#1

#1

306 ns
ns
#1
#1
ns
ns
ns
#1

305
ns

302

VSSAMARA09 - 7/18/2022 5:25 AM

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
301 4-532-593-02 SCREW (4X13) (TR-184A) 306 A-2199-446-A EXTENSION BOARD, COMPLETE
302 4-532-593-02 SCREW (4X13) (TR-184A) #1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
303 X-2595-666-3 COVER, BOTTOM ASSY ns not supplied
304 A-2193-430-A 360 BACK L BOARD, COMPLETE
305 A-2193-725-A 360 BACK R BOARD, COMPLETE

57
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.3

7-8. SPEAKER CABINET SECTION

• Distinguish the Part No. for:
Former type
LOUDSPEAKER (120MM) -270-11

ns

Part No. of LOUDSPEAKER

(120MM) -270-11

New type
LOUDSPEAKER (12CM)

351
SP1

351
SP5 SP3 Part No. of LOUDSPEAKER (12CM)

ns ns
ns

#1
356

352
ns ns
354
ns
ns
356

354
ns ns
ns 353
354
ns 355 ns
353 ns
355
354

Note: LOUDSPEAKER (12CM) for this set has been

changed in the midway of production. When any of
loudspeaker replacement is needed, check part num-
ber and order the same part for both channel. In case
of former type has finished consume, replace both
channel’s loudspeaker to new type at the same time.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
351 4-229-966-02 SCREW (4X16), +BV TAPPING SP1 1-859-311-11 LOUDSPEAKER (12CM) (Mid: L-CH)
352 4-229-966-02 SCREW (4X16), +BV TAPPING (new type) (See Note)
353 4-229-966-02 SCREW (4X16), +BV TAPPING SP3 1-859-270-11 LOUDSPEAKER (120MM)-270-11 (Mid: R-CH)
354 4-532-593-02 SCREW (4X13) (TR-184A) (former type) (See Note)
355 4-737-862-01 FOOT (CASTER)
SP3 1-859-311-11 LOUDSPEAKER (12CM) (Mid: R-CH)
356 4-874-614-02 SCREW (1) (3.5X14), TAPPING (new type) (See Note)
SP5 1-859-312-12 LOUDSPEAKER 30CM (Woofer) #1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
SP1 1-859-270-11 LOUDSPEAKER (120MM)-270-11 (Mid: L-CH) ns not supplied
(former type) (See Note)
58
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

7-9. TOP PANEL SECTION

414

SENSOR board (ns)

415

ns

ns 411
403

ns 401

410
406
402

ns 408
#1
ns

#1 VSSAMARA09 - 7/18/2022 5:25 AM

ND4000
407
409

ns

412
#1
413

404

405
Note: If flexible flat cable is replaced, install it after bending
#1 it in the same form as that before replacement.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
401 1-912-627-11 FLEXIBLE FLAT CABLE (5 CORE) 411 4-586-705-21 DOUBLE ADHESIVE TAPE
402 A-2193-429-A POWER KEY BOARD, COMPLETE 412 1-912-625-11 FLEXIBLE FLAT CABLE (7 CORE)
403 4-729-052-01 BUTTON, POWER TAIKO 413 1-912-626-11 FLEXIBLE FLAT CABLE (29 CORE)
404 A-2192-333-A VFD BOARD, COMPLETE 414 4-729-054-01 COVER, MIC USB
405 1-912-629-11 FLEXIBLE FLAT CABLE (7 CORE) 415 A-2203-717-A SERVICE, TOP PANEL ASSY
(Including SENSOR board) (V71D)
406 A-2192-335-A MIC USB BOARD, COMPLETE
407 1-912-624-11 FLEXIBLE FLAT CABLE (9 CORE) 415 A-2203-718-A SERVICE, TOP PANEL ASSY
408 1-912-623-11 FLEXIBLE FLAT CABLE (6 CORE) (Including SENSOR board) (V71)
409 2-677-839-01 +PWH 3X8 (SUMITITE) ND4000 1-483-549-11 VACUUM FLUORESCENT DISPLAY
410 A-2092-220-A NFC BOARD, COMPLETE #1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
ns not supplied

59
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

7-10. CDM SECTION

#1

CD/DVD mechanism section

(CDM90-DVBU204//M)

451

454

452
455 454 452
454
454
ns
(US, CND, AEP, UK, RU,
MY, AUS, E4)

ns

453

453
453

453

ns

ns
ns ns

ns

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
451 4-535-577-01 STEP SCREW M2.6 455 1-469-829-11 CORE, FERRITE
452 2-345-115-01 SCREW (S), FLOAT (US, CND, AEP, UK, RU, MY, AUS, E4)
453 4-590-159-01 SPRING, INSULATOR
454 4-533-382-01 INSULATOR #1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
ns not supplied

60
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1

7-11. CD/DVD MECHANISM SECTION

(CDM90-DVBU204//M)

ns
501 (including MS-476 board)

ns

VSSAMARA09 - 7/18/2022 5:25 AM ns

503

502
503

503 504

ns

ns

ns
MS-476
board (ns)

ns
505

506

Note: If flexible flat cable is replaced, install it after bending

it in the same form as that before replacement.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
501 A-1896-391-B LOADING COMPLETE ASSY (T) 505 1-912-622-11 FLEXIBLE FLAT CABLE (24 CORE)
(including MS-476 board)
502 3-087-599-01 INSULATOR SCREW 506 1-912-631-11 FLEXIBLE FLAT CABLE (5 CORE)
503 2-634-618-21 INSULATOR ns not supplied
0 504 A-2046-956-A SERVICE, OPTICAL DEVICE (7G)

61
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.1 SECTION 8
360 BACK L 360 BACK R ELECTRICAL PARTS LIST
360 FR L 360 FR R
METAL: Metal-film resistor. The components identified by mark 0
EXTENSION HUB METAL OXIDE: Metal oxide-film resistor. or dotted line with mark 0 are critical for
HUB //NON-EMC IR MIC USB F: nonflammable safety.
• Items marked “*” are not stocked since Replace only with part number specified.
MOTHERBOARD MS-476 they are seldom required for routine ser-
Les composants identifiés par une marque
NFC POWER KEY SENSOR vice.
0 sont critiques pour la sécurité.
Some delay should be anticipated when
SMPS SMPS (EMC) ordering these items.
Ne les remplacer que par une pièce portant
le numéro spécifié.
SPK MID L SPK MID R • SEMICONDUCTORS
In each case, u: µ, for example:
SW LED L SW LED R VFD uA. . : µA. . , uPA. . , µPA. . , The components identified by mark 9 con-
uPB. . : µPB. . , uPC. . , µPC. . , tain confidential information.
Note: Strictly follow the instructions whenever the
uPD. . : µPD. .
• Due to standardization, replacements in components are repaired and/or replaced.
• CAPACITORS
the parts list may be different from the
uF: µF Les composants identifiés par la marque
parts specified in the diagrams or the com-
• COILS 9 contiennent des informations confidenti-
ponents used on the set.
uH: µH elles.
• -XX and -X mean standardized parts, so
they may have some difference from the Suivre scrupuleusement les instructions
original one. When indicating parts by reference num- chaque fois qu’un composant est remplacé
• RESISTORS ber, please include the board name. et / ou réparé.
All resistors are in ohms.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
A-2193-430-A 360 BACK L BOARD, COMPLETE MS-476 BOARD
************************* ************
*************************************************************
When the MS-476 board is defective, exchange the entire LOADING COMPLETE
A-2193-725-A 360 BACK R BOARD, COMPLETE ASSY (T).
************************* *************************************************************
*************************************************************
A-2092-220-A NFC BOARD, COMPLETE
A-2192-340-A 360 FR L BOARD, COMPLETE ********************
*********************** *************************************************************
*************************************************************
A-2193-429-A POWER KEY BOARD, COMPLETE
A-2192-341-A 360 FR R BOARD, COMPLETE **************************
*********************** *************************************************************
*************************************************************
SENSOR BOARD
A-2199-446-A EXTENSION BOARD, COMPLETE *************
**************************
************************************************************* When the Sensor board is defective, exchange the entire SERVICE, TOP PANEL
ASSY.
A-2197-353-A HUB BOARD, COMPLETE *************************************************************
(US, CND, AEP, UK, RU, MY, AUS, E4)
A-2216-749-A HUB //NON-EMC BOARD, COMPLETE 0 A-2203-517-A SMPS BOARD, COMPLETE
(EA, BR, AR, LA9, E12) (EA, BR, AR, LA9, E12)
***************************** 0 A-2203-518-A SMPS (EMC) BOARD, COMPLETE
************************************************************* (US, CND, AEP, UK, RU, MY, AUS, E4)
**************************
A-2192-334-A IR BOARD, COMPLETE *************************************************************
******************
************************************************************* A-2192-345-A SPK MID L BOARD, COMPLETE
*************************
A-2192-335-A MIC USB BOARD, COMPLETE *************************************************************
***********************
************************************************************* A-2192-344-A SPK MID R BOARD, COMPLETE
*************************
9 A-2197-390-A MOTHERBOARD BOARD, COMPLETE *************************************************************
(for SERVICE) (V71)
9 A-2197-394-A MOTHERBOARD BOARD, COMPLETE A-2192-346-A SW LED L BOARD, COMPLETE
(for SERVICE) (EA, BR, AR, LA9, E12) ************************
9 A-2197-395-A MOTHERBOARD BOARD, COMPLETE *************************************************************
(for SERVICE) (AEP, UK, RU, MY, AUS, E4)
***************************** A-2192-347-A SW LED R BOARD, COMPLETE
************************
< IC > *************************************************************

IC2001 6-723-247-01 IC TAS5534DGGR-S A-2192-333-A VFD BOARD, COMPLETE

IC2002 6-723-793-01 IC TAS5634 ********************
************************************************************* *************************************************************

Note 1: When the MOTHERBOARD board is replaced, spread

the compound referring to “NOTE OF REPLACING
IC2002 ON THE MOTHERBOARD BOARD AND THE Note 2: When the complete MOTHERBOARD board is replaced,
COMPLETE MOTHERBOARD BOARD” on servicing be sure to refer to “DESTINATION SETTING METHOD”
notes (page 6). on supplement-1.

62
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.3

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
MISCELLANEOUS 4-733-312-71 MANUAL, INSTRUCTION
************** (TRADITIONAL CHINESE, MALAY) (MY)
4-733-312-81 MANUAL, INSTRUCTION (ARABIC) (EA, E4)
0 153 1-855-006-41 FAN, DC 4-734-747-11 MANUAL, INSTRUCTION (SPANISH) (AR)
201 1-457-369-12 CORE, FERRITE
(US, CND, AEP, UK, RU, MY, AUS, E4) 4-734-747-21 MANUAL, INSTRUCTION (PORTUGESE) (E4)
* 204 1-500-082-11 CLAMP, SLEEVE FERRITE 4-734-747-31 MANUAL, INSTRUCTION (RUSSIAN, UKRAINIAN)
(US, CND, AEP, UK, RU, MY, AUS, E4) (RU)
260 1-912-628-12 FLEXIBLE FLAT CABLE (17 CORE) 4-734-747-42 MANUAL, INSTRUCTION (PORTUGESE) (BR)
261 1-912-630-12 FLEXIBLE FLAT CABLE (4 CORE) 4-735-851-11 MANUAL, INSTRUCTION (ENGLISH(US)) (V71)
4-735-851-21 MANUAL, INSTRUCTION (FRENCH, SPANISH)
401 1-912-627-11 FLEXIBLE FLAT CABLE (5 CORE) (V71)
405 1-912-629-11 FLEXIBLE FLAT CABLE (7 CORE)
407 1-912-624-11 FLEXIBLE FLAT CABLE (9 CORE)
408 1-912-623-11 FLEXIBLE FLAT CABLE (6 CORE)
412 1-912-625-11 FLEXIBLE FLAT CABLE (7 CORE)

413 1-912-626-11 FLEXIBLE FLAT CABLE (29 CORE)

415 A-2203-717-A SERVICE, TOP PANEL ASSY
(Including SENSOR board) (V71D)
415 A-2203-718-A SERVICE, TOP PANEL ASSY
(Including SENSOR board) (V71)
455 1-469-829-11 CORE, FERRITE
(US, CND, AEP, UK, RU, MY, AUS, E4)
501 A-1896-391-B LOADING COMPLETE ASSY (T)
(including MS-476 board)

0 504 A-2046-956-A SERVICE, OPTICAL DEVICE (7G)

505 1-912-622-11 FLEXIBLE FLAT CABLE (24 CORE)
506 1-912-631-11 FLEXIBLE FLAT CABLE (5 CORE)
SP1 1-859-270-11 LOUDSPEAKER (120MM)-270-11 (Mid: L-CH)
(former type) (See Note 2)
SP1 1-859-311-11 LOUDSPEAKER (12CM) (Mid: L-CH)
(new type) (See Note 2)

SP2 1-859-269-11
LOUDSPEAKER (5CM) (Tweeter) (L-CH)
SP3 1-859-270-11
LOUDSPEAKER (120MM)-270-11 (Mid: R-CH)
(former type) (See Note 2)
SP3 1-859-311-11 LOUDSPEAKER (12CM) (Mid: R-CH)
(new type) (See Note 2)
SP4 1-859-269-11 LOUDSPEAKER (5CM) (Tweeter) (R-CH)
VSSAMARA09 - 7/18/2022 5:25 AM
SP5 1-859-312-12 LOUDSPEAKER 30CM (Woofer)
*************************************************************

ACCESSORIES
************

1-493-294-11 REMOTE COMMANDER (RMT-AM330U) (V71)

1-493-448-11 REMOTE COMMANDER (RMT-AM420U) (V71D)
1-754-852-11 ANTENNA (FM)
0 1-785-504-21 ADAPTOR, CONVERSION (MY, LA9, E4)
0 1-849-798-41 POWER SUPPLY CORD SET (V71)

0 1-849-799-51 POWER SUPPLY CORD SET

(AEP, RU, MY, LA9, E4)
0 1-849-801-51 POWER SUPPLY CORD SET (BR)
0 1-849-803-51 POWER SUPPLY CORD SET (AR)
0 1-849-804-52 POWER SUPPLY CORD SET (AUS)
0 1-912-321-51 POWER SUPPLY CORD SET (E12)

0 1-912-331-21 POWER SUPPLY CORD SET (UK, EA)

4-733-312-14 MANUAL, INSTRUCTION (ENGLISH)
(UK, EA, MY, AUS, LA9, E4, E12)
4-733-312-23 MANUAL, INSTRUCTION (SPANISH) (LA9)
4-733-312-33 MANUAL, INSTRUCTION (SPANISH) (AEP)
4-733-312-43 MANUAL, INSTRUCTION (FRENCH)
(AEP, EA, E4)

4-733-312-53 MANUAL, INSTRUCTION (GERMAN, DUTCH)

(AEP)
4-733-312-63 MANUAL, INSTRUCTION (ITALIAN, POLISH) Note 2: LOUDSPEAKER (12CM) for this set has been changed
(AEP) in the midway of production. When any of loudspeaker
replacement is needed, check part number and order the
same part for both channel. In case of former type has
Note 1: If flexible flat cable is replaced, install it after bending it in finished consume, replace both channel’s loudspeaker to
the same form as that before replacement. new type at the same time.

63
SYS SET
 MHC-V71/V71D
2020/04/28 00:01:32 (GMT+09:00)

US Model
Canadian Model

SERVICE MANUAL
MHC-V71

AEP Model
UK Model
Ver. 1.1 2018.05 E Model
Australian Model
MHC-V71D

SUPPLEMENT-1
File this supplement with the service manual.

Subject: Addition of SERVICING NOTES

9-890-695-81

1
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
SECTION 1
SERVICING NOTES
DESTINATION SETTING METHOD
The destination information isn’t written in the MOTHERBOARD
board for the service.
Therefore, when the MOTHERBOARD board is replaced, be sure
to perform the destination setting (Important work).

Note 1: The initial setting destination of the MOTHERBOARD board

for the service is temporary set as “LATIN”. The message
“LATIN (T)” is displayed on the screen display panel.
Note 2: When distinguishing the destination of the product, refer to the
“MODEL IDENTIFICATION” on page 5.
Note 3: If destination setting isn’t performed, it is possibility to occur
the defect to each operation of this unit.
Note 4: Destination would be locked if it has changed for 5 times.

Procedure:
1. Touch two touch keys of the [FIESTA] and [TUNING + >]
simultaneously for 10 seconds during the demonstration mode.
2. It enters the destination setting mode, the message
"D XXXXX" is displayed on the screen display panel.
Note 5: I f the message "DESTLOCK" is displayed on the screen dis-
play panel, touch the [N] touch key to release from this mode.
Because the destination is locked, and it cannot change the des-
tination.
3. Touch [0 +] / [0 - ] touch key to select the destination based
on the set's country.

Screen Destination
Country
display code
"D ASIA" SP6, TH1 Southeast Asia countries
"D INDIA" E12 India
E3, E93, E4, Middle East & Africa
"D ME AFC"
SA2, EA3 countries
"D OCEANI" AU1 Australia & New Zealand
"D JAPAN" J1 Japan
"D BRAZIL" BR1 Brazil
"D N AME" UC2, CA2 America & Canada
Central & South America
"D LATIN" LA9, AR2
countries (except Brazil)
"D RUSSIA" RU1 Russia & CIS country
Europe countries (except
"D EUROPE" CEL, CEK
CIS country)
VSSAMARA09 - 7/18/2022 5:25 AM
4. Touch [N] touch key to confirm the selection.
5. "RESET" appears on the screen display panel. After that,
"SONY"appears on the screen display panel. The system auto-
matically turn on and off once. Please be sure that the system
stay at demo mode finally before switch off the power supply.
6. Mode in "MODEL, DESTINATION AND VERSION
DISPLAY MODE" on page 23 again to confirm on the model
& destination.

2
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D

MEMO

3
SYS SET
 MHC-V71/V71D
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
SECTION 1
DIAGRAMS
• Note for Schematic Diagrams

Note on Schematic Diagram:

US Model • All capacitors are in µF unless otherwise noted. (p: pF)
50 V or less are not indicated except for electrolytics
Canadian Model and tantalums.

SERVICE MANUAL
MHC-V71 • All resistors are in Ω and 1/4 W or less unless otherwise
specified.
AEP Model • 2 : nonflammable resistor.
• C : panel designation.
UK Model The components identified by mark 0
Ver. 1.2 2018.09 E Model or dotted line with mark 0 are critical for
safety.
Australian Model Replace only with part number specified.
MHC-V71D Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une piéce portant
le numéro spécifié.

• A : B+ Line.
• B : B– Line.
• H : Adjustment for repair.
• Voltage and waveforms are dc with respect to ground
under no-signal (detuned) conditions.

SUPPLEMENT-2

•
no mark : TUNER
* : Impossible to measure
Voltages are taken with a VOM (Input impedance 10 MΩ).
File this supplement with the service manual. Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
Subject: Addition of schematic diagram for SMPS and SMPS (EMC) boards tolerances.
• Circled numbers refer to waveforms.
• Signal path.
J : AUDIO (DIGITAL)
F : AUDIO (ANALOG)
VSSAMARA09 - 7/18/2022 5:25 AM f : TUNER (FM)
L : VIDEO
E : USB
J : CD/DVD PLAY
N : MIC
a : BLUETOOTH

9-890-695-82
MHC-V71/V71D
1
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D
Ver. 1.2

1-1. SCHEMATIC DIAGRAM - SMPS Board (EA, BR, AR, LA9, E12), SMPS (EMC) Board (US, CND, AEP, UK, RU, MY, AUS, E4) -

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

SMPS BOARD (EA, BR, AR, LA9, E12) /

A SMPS (EMC) BOARD (US, CND, AEP, UK, RU, MY, AUS, E4) ET6000 (CHASSIS)

JS6000
CN6500
8P
JL6534 JL6535 JL6513
EA, BR, AR, LA9, E12 9 V1
R6556
JS6002 JS6001 10k EA, BR, AR, LA9, E12 JL6514
8 V1
C6000 C6003 4.7k US, CND, AEP, UK,RU, MY, AUS, E4
JS6004 JS6003 JL6515
~ AC IN F6000 0.0022 0.0022 7 V1
CN6000
10A 250V JL6516
B 2 D6000
D15JAB80 JL6517
6 V1 MOTHERBOARD
1 JL6001 JL6000 US, CND, AEP, UK, TH6000 5 V1_GND
BOARD

0.1
RU, MY, AUS, E4 ~ JL6518
C6007 VR6000 LF6001 LF6000
-
~
+ JL6519
4 V1_GND
CN2007
3 V1_GND

C6006
0.33
C6500 JL6520
JL6002 JS6005 470p 1 V1_GND
JL6542
JS6006 US, CND, AEP,
EA,

FB6501
JS6007 UK, RU, MY, R6555
JS6008 0 BR,

-
AUS, E4

FCF10A40
AR,

D6504
C EA, BR, AR, LA9, E12 LA9,

+
R6536 47k
D6001 JS6501 E12
R6535 47k
LB10S ET6500
C6321 R6557 22k
0.001 R6558 22k

470 80V

470 80V
C6505

C6506
(CHASSIS)

0.1
0.1
R6547 3.3k R6559 22k
R6548 3.3k R6560 22k

C6529
C6507
1 18 R6561
JS6500 R6549 3.3k
22k
2 17 R6550 3.3k
F6500 C6501
D R6322
47k
R6326
47k
C6314
0.0047
3 6.3A 250V 470p JS6505
0 NO6501
4 15 11P
JS6503 JL6536
5 14 1 A-SUPPLY
R6335 0.47
13 C6515 JL6503
0.1 JL6504
JS6301 7 D6501 3 AGND
D6307 11 FCH08A15 JS6504
C6322 C6301 SARS10 C6524 C6534 4 M-SUPPLY
9 10
220 450V 220 450V 1 2200 35V C6523
0.1 JL6506
JL6507
5 M-SUPPLY MOTHERBOARD
E JL6531
6 M/DGND BOARD
T6300 7 M/DGND
CN001

RF101LP4S
TRANSFORMER 0 JL6508

D6312
R6523 2.1
R6539 8 AC-DET
Q6501 JL6532 1k JL6533 1k JL6509
PZTA42G 9 MAIN ON
SWITCH 0.7 Q6504 0.7 JL6510
JS6302 PZTA42G 10 NETWORK ON

R6521
R6538 JL6511

10k
SWITCH 10k 11 LATCH ON
JL6512
Q6304
2SC2655L-Y
R6318
F 3.3k
REGULATOR
21.6 27.6

R6315 R6319
4.7

DZ2J24000L
21.9 3.3k R6330 R6525
4.7k R6537

D6515
22.4 0
Q6302 JL6304 JL6303 2.2k
R6321

2.3
100k
C6310

2SCR543RTL
47p

47 100V
R6316 JL6302

C6319

DZ2J220M0L
DRIVER
100 35V
C6313

2.2

D6509
2.4
Q6301 R6545
C6317 470p
DZ2J24000L
JL6309

280.1 TK10A80W 100k

DRIVER R6514 R6520
G 68k 33k R6542
D6308

R6312 R6333 47k

2.0 FB6301 100

DZ2J220M0L
3.3k
47p
C6311

D6510
R6515 C6510 R6546 R6543 R6540
R6306 68k 0.001 100 8.2k
4.7k
2.4 21.7 202.4 1k
DA2J10100L

S JS6300
C6303 0.3 0 Q6507
DRV 5
VCC 6

HV 8

220p Q6506 2SCR523UBTL

R6516
39k

Q6300
DZ2J27000L

C6509 47k C6511 2SCR523UBTL DETECT

C6320 280.3 TK10A80W 0.001 0.7
D6313

IC6300 0.047 DETECT SWITCH 0.7 SWITCH

22k
220p

JL6524
R6300 DRIVER NCP1240AD100R2G JL6525
R6340

C6522

JL6527
D6340

2M 0.001
2.0 FB6300 IC6300 R6517 0

R6544
JL6305

H R6509 1k

DA2J10100L
DA2J10100L
R6309 SWITCHING MODE R6518 C6521 R6541
R6301 120k 0.001
DZ2J220M0L

D6516
2.4 10k

D6502
100 8.2k
0.47

2M S POWER SUPPLY
C6340
DA2J10100L 0.001

D6311

0.3 Q6303 2.3 CONTROL

1 LATCH

JL6523
2SAR543RTL JL6528
4 GND

R6305
C6307

R6302 JL6522
3 CS

DRIVER
2 FB

2M 4.7k
28.6

DZ2J220M0L
0.5 R6504 *
15k
D6341

DA2J10100L
R6334

D6511
3 4
0.3 1.4 1.2 1k
D6503

PH6301 R6507 IC6500

EL816S1 (B) (TA) (DTE-S) JL6526 270 KV REF MM1431CURE

R6310 R6313
R6341
5.6k
R6502
1.8k
R6505
15k
IC6500 UVP CIRCUIT
I SHUNT REGULATOR
R6336

0 1.5k 24.1
100k

JL6530 R6508 A
DA2J10100L

* C6504
2.2 100V 270 2 1
D6306

Q6305
4.2 2PB709ART D6500 D6505
R6328 SWITCH
4.7k DZ2J120M0L DZ2J120M0L
DZ2J300M0L

C6305
D6303

220p
R6551
1k

R6303
0.04 10k
JL6521

PH6302
R6339

R6307 EL816S1 (B) (TA) (DTE-S)

TH6300

J 330k
R6501
0.0047

C6312
C6309

JL6308

0.01 100k

R6512
100

R6338
10k JL6306
JS6010 JS6009 0
0 0 R6500
K JL6538 JL6541
Q6307
RHK005N03T146 0
JL6307 JL6529 100k JL6500 Q6500
2SCR523UBTL
0.6
SWITCH C6502 AC DET
R6320 0.01 R6503 US, CND, AEP, UK,
JL6301 470k JL6300 2.4 PH6300 22k RU, MY, AUS, E4
EL816S1 (B) (TA) (DTE-S)
DZ2J100M0L

R6554
C6300 R6323 C6315 FB6502
D6300

0.047 R6327 0
330k 470k 0.047 S
0
ET6501 (CHASSIS)
EA, BR, AR,
LA9, E12

MHC-V71/V71D
2 2
SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D

REVISION HISTORY

Ver. Date Description of Revision

1.0 2018.02 New
VSSAMARA09
1.1 2018.05 - 7/18/2022
Addition of MHC-V71 model. 5:25 AM
Addition Argentina and Malaysia models (MHC-V71D).
Addition of SERVICING NOTES (SUPPLEMENT-1).
Add CN3007, FB013 and R2153 in MOTHERBOARD board.
Add R070 in MOTHERBOARD board for MHC-V71D.
Add one CLAMP (N) in page 17 and 54.
Change of MOTHERBOARD board (Suffix 21).
Change of CUSHION (QJ, S) to ACOUSTIC TAPE in page 18.
Change of SMPS board and SMPS (EMC) board (Suffix 12).
Change P/N of Ref. No. 51 in page 52.
Change P/N of Ref. No. 262 in page 56.
Change P/N of Ref. No. 303 in page 57.
Change P/N of Ref. No. 351, 352 and 353 in page 58.
Change P/N of MANUAL, INSTRUCTION (PORTUGESE) for Brazilian model in ACCESSORIES
section.
Change of SCREW (1) (4X20), +BV TAPPING to SCREW (4X16), +BV TAPPING in page 20 and 21.
Change screw P/N from 7-685-647-79 to 7-685-647-71 for PANEL, FRONT ASSY (VANILLA)
in page 56.
Change P/N of MOTHERBOARD BOARD, COMPLETE (for SERVICE) in page 54 and 62.
Change wire setting illustration in page 17 (Add one CLAMP (N)).
Change wire setting illustration in page 18 (Change of CUSHION (QJ, S) to ACOUSTIC TAPE).
Delete two CUSHION, SARANET in CHASSIS ASSY.
Delete C078, C079 and IC008 in MOTHERBOARD board for MHC-V71D.
Delete CN113 and R048 in MOTHERBOARD board.
Delete C4306, C4307, C4308, C4309, C4310, C4311 and C4319 in HUB //NON-EMC board.
1.2 2018.09 Addition of schematic diagram for SMPS and SMPS (EMC) boards (SUPPLEMENT-2).
Add information of “Distinguish the Part No. of LOUDSPEAKER (12CM) and LOUDSPEAKER
(120MM) -270-11” in page 58.
Add note for LOUDSPEAKER (12CM) in page 58 and 63.
Add P/N and description of LOUDSPEAKER (12CM) in page 58 and 63 (midway of production changed).
Change of LOUDSPEAKER (120MM) -270-11 to LOUDSPEAKER (12CM) in page 21.
Change of LOUDSPEAKER (320MM) -266-11 to LOUDSPEAKER 30CM in page 20.
Change of MOTHERBOARD board (Suffix 31).
Change P/N and description of Ref. No. SP5 in page 58 and 63.
Change P/N from 4-729-055-11 to 4-729-055-01 for PANEL, SIDE L (V71) in page 51.
Change P/N from 4-729-056-11 to 4-729-056-01 for PANEL, SIDE R (V71) in page 51.
Change P/N from 4-729-065-11 to 4-729-065-01 for COVER, REAR (V71) in page 52.
Change P/N of model number label for US, CND in page 5.
1.3 2020.04 Change License and Trademark Notice’s in page 2.
Change CLASS 1 LASER marking statement for EA version in page 4.
Change suffix number of LOUDSPEAKER 30CM in page 58 and 63.

SYS SET
2020/04/28 00:01:32 (GMT+09:00)
MHC-V71/V71D

Ver. Date Description of Revision

How to search for a contact point of signal lines or the like in DIAGRAMS SECTION
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF file search function to find one.

e.g.) If a contact point is shown as , follow the procedure below.

Procedure:
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
Note: If you still see the original page, press the [Enter] key again.

SYS SET