SRC
SRC
SRC
SECTION
SRC
CONTENTS
BASIC INSPECTION ................................... 5 .
DIAGNOSIS AND REPAIR WORK FLOW ........ 5 .
Work Flow ................................................................ 5 .
SRC
SRC-1
2009 Z12
B1058, B1059, B1060, B1061, B1062, B1063 DIAGNOSIS SENSOR UNIT ............................ 61 .
Description ............................................................. 61 . DTC Logic .............................................................. 61 . Diagnosis Procedure .............................................. 61 .
B1026, B1027, B1028, B1029, B1030, B1031 DIAGNOSIS SENSOR UNIT ............................. 41 .
Description ............................................................. 41 . DTC Logic .............................................................. 41 . Diagnosis Procedure ............................................. 41 .
B1074, B1075, B1076, B1077, B1078, B1079 DIAGNOSIS SENSOR UNIT ............................ 71 .
Description ............................................................. 71 . DTC Logic .............................................................. 71 . Diagnosis Procedure .............................................. 71 .
B1042, B1043, B1044, B1045, B1046, B1047 DIAGNOSIS SENSOR UNIT ............................. 51 .
Description ............................................................. 51 . DTC Logic .............................................................. 51 . Diagnosis Procedure ............................................. 51 .
SRC-2
2009 Z12
B1122, B1123, B1124, B1125, B1126, B1127 DIAGNOSIS SENSOR UNIT ........................... 107
Description ............................................................ 107 . DTC Logic ............................................................. 107 . Diagnosis Procedure ............................................ 107 .
B1090, B1091, B1092, B1093, B1094, B1095 DIAGNOSIS SENSOR UNIT .............................91 .
Description ............................................................. 91 . DTC Logic .............................................................. 91 . Diagnosis Procedure .............................................. 91 .
B1106, B1107, B1108, B1109, B1110, B1111 DIAGNOSIS SENSOR UNIT .............................93 .
Description ............................................................. 93 . DTC Logic .............................................................. 93 . Diagnosis Procedure .............................................. 93 .
SRC
B1138, B1139, B1140, B1141, B1142, B1143 DIAGNOSIS SENSOR UNIT ........................... 125
Description ............................................................ 125 . DTC Logic ............................................................. 125 . Diagnosis Procedure ............................................ 125 .
SRC-3
2009 Z12
B1218, B1219, B1220, B1221, B1222, B1223 DIAGNOSIS SENSOR UNIT ........................... 162 .
Description ........................................................... 162 . DTC Logic ............................................................ 162 . Diagnosis Procedure ............................................ 162 .
B1154, B1155, B1156, B1157, B1158, B1159 DIAGNOSIS SENSOR UNIT ........................... 144 .
Description ............................................................144 . DTC Logic .............................................................144 . Diagnosis Procedure ............................................144 .
B1170, B1171, B1172, B1173, B1174, B1175 DIAGNOSIS SENSOR UNIT ........................... 146 .
Description ............................................................146 . DTC Logic .............................................................146 . Diagnosis Procedure ............................................146 .
B1186, B1187, B1188, B1189, B1190, B1191 DIAGNOSIS SENSOR UNIT ........................... 148 .
Description ............................................................148 . DTC Logic .............................................................148 . Diagnosis Procedure ............................................148 .
SRS AIR BAG WARNING LAMP DOES NOT TURN ON ......................................................... 176 .
Diagnosis Procedure ............................................ 176 .
B1202, B1203, B1204, B1205, B1206, B1207 DIAGNOSIS SENSOR UNIT ........................... 150 .
Description ............................................................150 . DTC Logic .............................................................150 . Diagnosis Procedure ............................................150 .
SRC-4
2009 Z12
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow
OVERALL SEQUENCE
INFOID:0000000005023239
SRC
JMHIA1324GB
DETAILED FLOW
Revision: 2009 March
SRC-5
2009 Z12
2.CHECK SYMPTOM
Check the symptom from the customer information. >> GO TO 3.
SRC-6
2009 Z12
10.FINAL CHECK
Check self diagnostic result and air bag warning lamp operation in the user mode. Is the malfunction repaired? YES >> INSPECTION END NO >> GO TO 2.
C
SRC
SRC-7
2009 Z12
When replacing or removing and installing passenger seat, always perform zero point reset so that Occupant Detection System is activated normally.
INFOID:0000000005023024
Zero point reset is an initializing procedure for occupant detection sensor that must be performed when replacing or removing and installing passenger seat. If zero point reset is not performed, the initialization is incomplete and Occupant Detection System does not operate normally. NOTE: When replacing passenger seat with a NISSAN genuine part, air bag warning lamp blinks if zero point reset is incomplete. When zero point reset is performed once after removal and installation of passenger seat, CONSULT-III displays complete and air bag warning does not blink. When reinstalling passenger seat after removal, the initial value for occupant detection sensor changes, and Occupant Detection System does not operate normally. Always perform zero point reset after performing the work as per the following. - Reinstallation of passenger seat - Replacement of passenger seat with a seat that is zero point reset complete.
INFOID:0000000005023026
2. 3.
2.CONFIRMATION OF SETTING
Proceed to Zero point reset function screen from work support of CONSULT-III OCCUPANT DETECTION. 2. Check that Complete or Incomplete is displayed on Zero point reset status. CAUTION:
Revision: 2009 March
1.
SRC-8
2009 Z12
SRC
SRC-9
2009 Z12
SYSTEM DESCRIPTION
SRS AIR BAG SYSTEM
System Diagram
INFOID:0000000005015971
JMHIA1078GB
System Description
INFOID:0000000005015972
Supplemental Restraint System (SRS) activates air bag module and seal belt pre-tensioner when it detects a frontal collision or a side collision that is more than the specified limit. Together with other safety devices, it reduces the impact that occupant receives when vehicle collision occurs. Air bag diagnosis sensor unit supplies power supply to air bag module and pre-tensioner seat belt when deceleration that is more than the specified limit is detected by G sensor in air bag diagnosis sensor unit, crash zone sensor, or satellite sensor. Air bag module is composed of electric igniter (squib), filter, pyrotechnic material, and gas generating material. When air bag module receives a signal from air bag diagnosis sensor unit, air bag module ignites pyrotechnic material using electric igniter (squib) so that gas generating material generates high temperature nitrogen gas. The gas through filter activates air bag. At the same time, pre-tensioner seat belt receives power supply from air bag diagnosis sensor unit, gasgenerator is activated, and then gas is generated. Balls in pipe are moved according to generated gas pressure and strike pinion gear on ELR shaft. ELR shaft rotates and retracts seat belt.
Revision: 2009 March
SRC-10
2009 Z12
COLLISION MODES
The operation of SRS is different depending on the collision modes applications. For example, the driver air bag module, passenger air bag module, and seat belt pre-tensioner are activated in a frontal collision but not in a side collision. SRS configurations that are activated for the following collision modes.
: Apply : Not apply
SRS configuration Driver air bag module. Passenger air bag module. Seat belt pre-tensioner LH. Seat belt pre-tensioner RH. Side air bag module LH. Side air bag module RH. Curtain air bag module LH. Curtain air bag module RH.
Frontal collision
SRC
SRC-11
2009 Z12
INFOID:0000000005015973
JMHIA1080ZZ
1.
Curtain air bag module LH/RH LH B72 RH B56 Air bag diagnosis sensor unit B13, B14, M59 Passenger air bag module M62
2.
Seat belt pre-tensioner LH/RH LH B36 RH B29 Occupant Detection System seat sensor Crash zone sensor E33
3.
Satellite sensor LH/RH LH B37 RH B30 Occupant Detection System control unit B12 Passenger air bag OFF indicator M64
4. 7.
5. 8.
6. 9.
10. Combination meter M34 Refer to 11. Combination switch (spiral cable) MWI-8, "METER SYSTEM : CompoM32 nent Parts Location"
SRC-12
2009 Z12
Component Description
Component Air bag diagnosis sensor unit Air bag module Driver Passenger Side Curtain Seat belt pre-tensioner Seat belt buckle switch Crash zone sensor Satellite sensor (LH/RH) Occupant Detection System control unit Combination meter (air bag warning lamp) Passenger air bag OFF indicator Combination switch (spiral cable) Function
D
Detects a collision and supplies power supply for deployment to air bag module and pre-tensioner seat belt.
Receives signal from air bag diagnosis sensor unit and deploys air bag.
Receives signal from air bag diagnosis sensor unit and deploys seat belt pre-tensioner. Controls deployment timing based on seat belt fastened or unfastened condition. Transmits signal to air bag diagnosis sensor unit when a frontal collision occurs. Transmits signal to air bag diagnosis sensor unit when a side collision occurs. Detects passenger seat occupant and judges whether or not passenger seat air bag is deployed. Indicates air bag malfunctioning and deployment by blinking and illuminating air bag warning lamp. Indicates whether or not passenger air bag is in the activation mode based on the judgement of Occupant Detection System. Supplies power supply to driver air bag module on steering wheel.
SRC
SRC-13
2009 Z12
JMHIA1079GB
System Description
This Occupant Detection System has the following functions.
INFOID:0000000005016352
Suppress the deployment of passenger air bag when passenger seat is empty, or when occupied by child and child-seat. Turns ON passenger air bag OFF indicator when passenger seat is occupied by child-seat and child. Indicates malfunction portion with blinking times of air bag warning lamp in diagnosis mode. Indicates the malfunctioning record by CONSULT-III. When zero point reset for Occupant Detection System is incomplete, CONSULT-III indicates that zero point reset is incomplete. This function is applied to NISSAN genuine parts only. NOTE: Operation of air bag diagnosis sensor unit when air bag diagnosis sensor unit receives information from Occupant Detection System. Even if zero point reset is complete, always perform zero point reset after the removal and installation of seat or the removal of control unit harness connector.
Status (passenger seat) Empty An object Child/ child-seat Adult Malfunction Zero point reset Not yet performed (NISSAN genuine parts only) Passenger air bag Suppress Suppress Suppress Enable to deploy Suppress Suppress Passenger air bag OFF indicator OFF ON ON OFF ON ON Air bag warning lamp OFF OFF OFF OFF Blinking Blinking
SRC-14
2009 Z12
INFOID:0000000005141753
SRC
JMHIA1080ZZ
1.
Curtain air bag module LH/RH LH B72 RH B56 Air bag diagnosis sensor unit B13, B14, M59 Passenger air bag module M62
2.
Seat belt pre-tensioner LH/RH LH B36 RH B29 Occupant Detection System seat sensor Crash zone sensor E33
3.
Satellite sensor LH/RH LH B37 RH B30 Occupant Detection System control unit B12 Passenger air bag OFF indicator M64
4. 7.
5. 8.
6. 9.
10. Combination meter M34 Refer to 11. Combination switch (spiral cable) MWI-8, "METER SYSTEM : CompoM32 nent Parts Location"
SRC-15
2009 Z12
Component Description
Component parts Occupant Detection System sensor Occupant Detection System control unit Passenger air bag OFF indicator Outline of function Detects if the passenger seat is empty or occupied
Transmits the passenger seat status (occupied or empty) to air bag diagnosis sensor unit Turns the passenger air bag OFF indicator lamp ON when the passenger seat is occupied by a child or a child-seat Performs the deploy judgement of passenger air bag based on the information from Occupant Detection System control unit. Passenger air bag OFF indicator turns ON or turns OFF when passenger state signal detected by Occupant Detection System control unit is received.
SRC-16
2009 Z12
CAUTION: Never use electrical test equipment on any circuit related to the SRS unless instructed in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors. Never repair, splice or modify the SRS wiring harness. If the harness is damaged, replace it with a new one. Keep ground portion clean.
DIAGNOSIS FUNCTION
The SRS self-diagnosis results can be read with air bag warning lamp and/or CONSULT-III. The user mode is exclusively prepared for the customer (driver). This mode warns the driver of a system malfunction through the operation of the air bag warning lamp. The diagnosis mode allows the technician to locate and inspect the malfunctioning part. The mode applications for the air bag warning lamp and CONSULT-III are as per the following items.
: Application, : Not application
User mode
Diagnosis mode
INFOID:0000000005015980
SRC
USER MODE
In USER MODE, air bag warning lamp on combination meter blinks when a malfunction is detected and warns the customer (driver).
How to Read Air Bag Warning Lamp
1. 2.
Turn the ignition switch from OFF to ON, and check that the air bag warning lamp blinks. Compare the air bag warning lamp blinking pattern with the examples.
SRC-17
2009 Z12
SHIA0011E
The system is malfunctioning Self diagnostic result is not erased after repair
Erase Self Diagnostic Result Refer to SRC-23, "CONSULT-III Function", How to Erase Self-diagnostic Result Check CAUSE OF WARNING in Special Function with CONSULTIII. Refer to SRC-23, "CONSULT-III Function" Go to SRC-8, "ZERO POINT RESET : Description" Go to GI-34, "Intermittent Incident" Go to SRC-152, "Diagnosis Procedure" or SRC-154, "Diagnosis Procedure"
Intermittent malfunction is detected in the past Air bag is deployed Seat belt pre-tensioner is deployed
Air bag diagnosis sensor unit is malfunctioning Air bag power supply circuit is malfunctioning Air bag warning lamp circuit is malfunctioning
SHIA0013E
Air bag diagnosis sensor unit is malfunctioning Air bag warning lamp circuit is malfunctioning
SHIA0014E
DIAGNOSIS MODE
The diagnosis mode can only be switched when a malfunction is detected in the user mode. Malfunctioning system is indicated according to blinking pattern of air bag warning lamp.
How to Read Air Bag Warning Lamp
1. 2.
Follow the procedures of PROCEDURE TO CHANGE DIAGNOSIS MODE, and switch to the diagnosis mode. Turn ignition switch ON. Check the blinking pattern of air bag warning lamp. There are 2 blinking patterns for the air bag warning lamp as per the following items.
SRC-18
2009 Z12
Malfunctioning items Self-diagnostic result is not erased after repair Intermittent malfunction is detected in the past
Blinking pattern Refer to the following items Refer to How to Erase Self-diagnostic Result GI-34, "Intermittent Incident" Refer to the following items SRC-83, "DTC Logic" SRC-85, "DTC Logic" SRC-87, "DTC Logic" SRC-89, "DTC Logic" Refer to the following items SRC-53, "DTC Logic" SRC-55, "DTC Logic" SRC-57, "DTC Logic" SRC-59, "DTC Logic" SRC-73, "DTC Logic" Refer to the following items SRC-75, "DTC Logic" SRC-77, "DTC Logic" SRC-79, "DTC Logic" SRC-81, "DTC Logic" Refer to the following items SRC-31, "DTC Logic" SRC-33, "DTC Logic" SRC-35, "DTC Logic" SRC-39, "DTC Logic" Refer to the following items SRC-43, "DTC Logic" SRC-45, "DTC Logic" SRC-47, "DTC Logic" SRC-49, "DTC Logic" Refer to the following items SRC-25, "DTC Logic" SRC-27, "DTC Logic" SRC-29, "DTC Logic" SRC-41, "DTC Logic" SRC-51, "DTC Logic" SRC-61, "DTC Logic" SRC-71, "DTC Logic" SRC-91, "DTC Logic" SRC-93, "DTC Logic" SRC-107, "DTC Logic" SRC-125, "DTC Logic" SRC-144, "DTC Logic" SRC-146, "DTC Logic" SRC-148, "DTC Logic" SRC-150, "DTC Logic" SRC-162, "DTC Logic" SRC-164, "DTC Logic" Refer to the following items SRC-63, "DTC Logic" SRC-65, "DTC Logic" SRC-67, "DTC Logic" SRC-69, "DTC Logic" Refer to SRC-37, "DTC Logic". Refer to SRC-127, "DTC Logic"
SRC
11 17
Passenger air bag OFF indicator Air bag diagnosis sensor unit
SRC-19
2009 Z12
Malfunctioning items
Blinking pattern Refer to the following items SRC-109, "DTC Logic" SRC-111, "DTC Logic" SRC-113, "DTC Logic" SRC-115, "DTC Logic" Refer to the following items SRC-117, "DTC Logic" SRC-119, "DTC Logic" SRC-121, "DTC Logic" SRC-123, "DTC Logic" Refer to the following items SRC-95, "DTC Logic" SRC-97, "DTC Logic" SRC-99, "DTC Logic" SRC-158, "DTC Logic" Refer to the following items SRC-101, "DTC Logic" SRC-103, "DTC Logic" SRC-105, "DTC Logic" SRC-160, "DTC Logic" Refer to the following items SRC-128, "DTC Logic" SRC-130, "DTC Logic" SRC-132, "DTC Logic" SRC-134, "DTC Logic" Refer to the following items SRC-136, "DTC Logic" SRC-138, "DTC Logic" SRC-140, "DTC Logic" SRC-142, "DTC Logic"
Satellite sensor RH
Satellite sensor LH
How to Erase Self Diagnosis Result After a malfunction is repaired, turn the ignition switch OFF for one second or more, then turn ignition switch ON. The diagnosis mode returns to the user mode. At that time the self-diagnosis result is cleared.
JMHIA0945GB
SRC-20
2009 Z12
C
JMHIA0946GB
Side air bag system When curtain air bag module LH system (Item display 1) is malfunctioning.
G
JMHIA0948GB
Multiple Systems Malfunction Front air bag system SRC When driver air bag module (Item display 1) and air bag diagnosis sensor unit system (Item display 2) are malfunctioning. I
K
JMHIA0947GB
Side air bag system When satellite sensor LH (Item display1) and curtain air bag module LH system (Item display 2) are malfunctioning.
O
JMHIA0949GB
SRC-21
2009 Z12
JMHIA0950GB
SRC-22
2009 Z12
Function Test
SRC
SPECIAL FUNCTION
CAUSE OF WARNING This item indicates IGN low voltage condition. The air bag warning lamp blink in user mode when the battery voltage is lowered to the voltage value (less than 9 V) at which the SRS cannot be operated normally. The air bag warning lamp turns OFF after the battery voltage returns to normal status after blinking. In such a case, the DTC memory is not performed and changing to the self-diagnostic mode by IGN operation cannot be performed while the air bag warning lamp illuminates. NO DTC is displayed even if the malfunctioning parts are checked by CONSULT-III. This function records the following items.
Display contents of CONSULT-III IGN VOLT COND Air bag IGN VOLT TIME LOW V RECORED Description LOW is displayed when IGN low voltage is detected. If not, OK is displayed. Times of IGN low voltage is detected. Times of IGN ON after IGN low voltage is detected.
SRC-23
2009 Z12
WORK SUPPORT
Monitor item Zero point reset function Description Perform zero point reset. Refer to SRC-8, "ZERO POINT RESET : Special Repair Requirement".
SRC-24
2009 Z12
DTC/CIRCUIT DIAGNOSIS
B1001, B1002, B1003, B1004, B1005 DIAGNOSIS SENSOR UNIT
Description
INFOID:0000000005015982
It detects a shock that is more than the specified level and monitors whether the driver and passenger air bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally. It contains the G sensors for both frontal and side collisions and spare battery function in case of main battery damage in collision.
DTC Logic
DTC DETECTION LOGIC
DTC B1001 B1002 B1003 B1004 B1005 Display contents of CONSULT-III
INFOID:0000000005015983
E
DTC detecting condition Possible cause
F
CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning Malfunction in air bag diagnosis sensor unit
SRC
Diagnosis Procedure
INFOID:0000000005015984
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-25
2009 Z12
SRC-26
2009 Z12
It detects a shock that is more than the specified level and monitors whether the driver and passenger air bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally. It contains the G sensors for both frontal and side collisions and spare battery function in case of main battery damage in collision.
DTC Logic
DTC DETECTION LOGIC
DTC B1006 B1007 B1008 B1009 B1010 Display contents of CONSULT-III DTC detecting condition
INFOID:0000000005015986
D
Possible cause
E
Air bag diagnosis sensor unit is malfunctioning Malfunction in air bag diagnosis sensor unit
CONTROL UNIT
SRC
Diagnosis Procedure
INFOID:0000000005015987
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-27
2009 Z12
SRC-28
2009 Z12
It detects a shock that is more than the specified level and monitors whether the driver and passenger air bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally. It contains the G sensors for both frontal and side collisions and spare battery function in case of main battery damage in collision.
DTC Logic
DTC DETECTION LOGIC
DTC B1011 B1012 B1013 B1014 B1015 Display contents of CONSULT-III DTC detecting condition
INFOID:0000000005015989
D
Possible cause
E
Air bag diagnosis sensor unit is malfunctioning Malfunction in air bag diagnosis sensor unit
CONTROL UNIT
SRC
Diagnosis Procedure
INFOID:0000000005015990
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-29
2009 Z12
SRC-30
2009 Z12
This unit classifies occupant in passenger seat and detects electrical malfunctions in Occupant Detection System, and transmits malfunction information to air bag diagnosis sensor unit.
DTC Logic
DTC DETECTION LOGIC
DTC B1017 B1020 B1021 Display contents of CONSULT-III OCCUPANT SENS C/U [UNIT FAIL] DTC detecting condition Possible cause
INFOID:0000000005015992
Disconnection of wiring harness Malfunction in Occupant Detection System control unit Malfunction in air bag diagnosis sensor unit
SRC
Diagnosis Procedure
INFOID:0000000005015993
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
SRC-31
2009 Z12
SRC-32
2009 Z12
Occupant Detection System sensor detects occupant in passenger seat and transmits it to Occupant Detection System control unit.
DTC Logic
DTC DETECTION LOGIC
DTC Display contents of CONSULT-III OCCUPANT SENS [UNIT FAIL] DTC detecting condition Possible cause
INFOID:0000000005015995
B1018
Disconnection of wiring harness Malfunction in Occupant Detection System sensor Malfunction in Occupant Detection System control unit Malfunction in air bag diagnosis sensor unit
SRC
Diagnosis Procedure
INFOID:0000000005015996
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
SRC-33
2009 Z12
SRC-34
2009 Z12
This unit classifies occupant in passenger seat and detects electrical malfunctions in Occupant Detection System, and transmits malfunction information to air bag diagnosis sensor unit.
DTC Logic
DTC DETECTION LOGIC
DTC Display contents of CONSULT-III DTC detecting condition Internal malfunction of Occupant Detection System control unit Malfunction of circuit between Occupant Detection Sytem control unit and Air bag diagnosis sensor unit Malfunction of Air bag diagnosis sensor unit Possible cause
INFOID:0000000005015998
B1022
Disconnection of wiring harness Malfunction in Occpupant Detection System control unit Malfunction in air bag diagnosis sensor unit
SRC
Diagnosis Procedure
K
INFOID:0000000005015999
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
SRC-35
2009 Z12
SRC-36
2009 Z12
Illuminates passenger air bag OFF indicator when the passenger seat is empty or occupied by a child or a child-seat.
DTC Logic
DTC DETECTION LOGIC
DTC Display contents of CONSULT-III PASS A/B INDCTR CKT [UNIT FAIL] DTC detecting condition Passenger air bag OFF indicator circuit is open or shorted to ground or the circuits are shorted each other Possible cause
INFOID:0000000005016001
B1023
Disconnection of wiring harness Malfunction in passenger air bag OFF indicator Malfunction in air bag diagnosis sensor unit
SRC
Diagnosis Procedure
J
INFOID:0000000005016002
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
SRC-37
2009 Z12
SRC-38
2009 Z12
Occupant Detection System sensor detects occupant in passenger seat and transmits it to Occupant Detection System control unit.
DTC Logic
DTC DETECTION LOGIC
DTC Display contents of CONSULT-III DTC detecting condition Internal malfunction of Occupant Detection Sytem control unit Malfunction of circuit between Occupant Detection Sytem control unit and Air bag diagnosis sensor unit Malfunction of Air bag diagnosis sensor unit Possible cause
INFOID:0000000005016004
OCS SENSOR
Disconnection of wiring harness Malfunction in Occpupant Detection System control unit Malfunction in air bag diagnosis sensor unit
SRC
Diagnosis Procedure
INFOID:0000000005016005
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
SRC-39
2009 Z12
SRC-40
2009 Z12
It detects a shock that is more than the specified level and monitors whether the driver and passenger air bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally. It contains the G sensors for both frontal and side collisions and spare battery function in case of main battery damage in collision.
DTC Logic
DTC DETECTION LOGIC
DTC B1026 B1027 B1028 B1029 B1030 B1031 Display contents of CONSULT-III DTC detecting condition
INFOID:0000000005016007
D
Possible cause
CONTROL UNIT
Diagnosis Procedure
INFOID:0000000005016008
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-41
2009 Z12
SRC-42
2009 Z12
Crash zone sensor is a G sensor that outputs voltage signal during deceleration at the time of a vehicle frontal collision that is more than the specified limit is detected.
DTC Logic
DTC DETECTION LOGIC
DTC B1033 B1034 Display contents of CONSULT-III CRASH ZONE SENSOR [UNIT FAIL] DTC detecting condition Possible cause
INFOID:0000000005016010
Disconnection of wiring harness Malfunction in crash zone sensor Malfunction in air bag diagnosis sensor unit
SRC
Diagnosis Procedure
J
INFOID:0000000005016011
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-43
2009 Z12
SRC-44
2009 Z12
Crash zone sensor is a G sensor that outputs voltage signal during deceleration at the time of a vehicle frontal collision that is more than the specified limit is detected.
DTC Logic
DTC DETECTION LOGIC
DTC Display contents of CONSULT-III CRASH ZONE SENSOR [COMM FAIL] DTC detecting condition
INFOID:0000000005016013
Possible cause Disconnection of wiring harness Malfunction in crash zone sensor Malfunction in air bag diagnosis sensor unit
B1035
SRC
Diagnosis Procedure
J
INFOID:0000000005016014
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-45
2009 Z12
SRC-46
2009 Z12
Crash zone sensor is a G sensor that outputs voltage signal during deceleration at the time of a vehicle frontal collision that is more than the specified limit is detected.
DTC Logic
DTC DETECTION LOGIC
DTC Display contents of CONSULT-III CRASH ZONE SENSOR [UNMATCH] DTC detecting condition Crash zone sensor is out of the specified specification Possible cause
INFOID:0000000005116544
B1036
Diagnosis sensor unit or crash zone sensor is different from the part specified
SRC
Diagnosis Procedure
J
INFOID:0000000005116545
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-47
2009 Z12
SRC-48
2009 Z12
Crash zone sensor is a G sensor that outputs voltage signal during deceleration at the time of a vehicle frontal collision that is more than the specified limit is detected.
DTC Logic
DTC DETECTION LOGIC
DTC B1037 B1039 B1041 Display contents of CONSULT-III CRASH ZONE SENSOR1 DTC detecting condition Possible cause
INFOID:0000000005016016
Disconnection of wiring harness Malfunction in crash zone sensor Malfunction in air bag diagnosis sensor unit
SRC
Diagnosis Procedure
J
INFOID:0000000005016017
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-49
2009 Z12
SRC-50
2009 Z12
It detects a shock that is more than the specified level and monitors whether the driver and passenger air bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally. It contains the G sensors for both frontal and side collisions and spare battery function in case of main battery damage in collision.
DTC Logic
DTC DETECTION LOGIC
DTC B1042 B1043 B1044 B1045 B1046 B1047 Display contents of CONSULT-III DTC detecting condition
INFOID:0000000005016019
D
Possible cause
CONTROL UNIT
Diagnosis Procedure
INFOID:0000000005016020
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-51
2009 Z12
SRC-52
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016022
D
DTC Display contents of CONSULT-III DRIVER AIRBAG MODULE [OPEN] DTC detecting condition Possible cause Disconnection of wiring harness and open Malfunction in driver air bag module Malfunction in spiral cable Malfunction in air bag diagnosis sensor unit
B1049 B1054
Driver air bag module circuit is open (including the spiral cable)
Diagnosis Procedure
INFOID:0000000005016023
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-53
2009 Z12
M351
4.
Check continuity between driver air bag module harness connector and ground.
Driver side air bag module Connector M350 Terminal 10 11 12 9 Ground Not existed Continuity
M351
Is the inspection result normal? YES >> GO TO 4. NO >> Replace combination switch (spiral cable). Refer to SR-5, "Exploded View".
SRC-54
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016025
D
DTC Display contents of CONSULT-III DRIVER AIRBAG MODULE [VB-SHORT] DTC detecting condition Driver air bag module circuit is shorted to power supply circuit (including the spiral cable) Possible cause Disconnection of wiring harness and short Malfunction in driver air bag module Malfunction in spiral cable Malfunction in air bag diagnosis sensor unit
B1050 B1055
Diagnosis Procedure
INFOID:0000000005016026
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-55
2009 Z12
M351
4.
Check continuity between driver air bag module harness connector and ground.
Driver side air bag module Connector M350 Terminal 10 11 12 9 Ground Not existed Continuity
M351
Is the inspection result normal? YES >> GO TO 4. NO >> Replace combination switch (spiral cable). Refer to SR-5, "Exploded View".
SRC-56
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016028
D
DTC Display contents of CONSULT-III DRIVER AIRBAG MODULE [GND-SHORT] DTC detecting condition Possible cause Disconnection of wiring harness and short Malfunction in driver air bag module Malfunction in spiral cable Malfunction in air bag diagnosis sensor unit
B1051 B1056
Driver air bag module circuit is shorted to ground (including the spiral cable)
Diagnosis Procedure
INFOID:0000000005016029
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-57
2009 Z12
M351
4.
Check continuity between driver air bag module harness connector and ground.
Driver side air bag module Connector M350 Terminal 10 11 12 9 Ground Not existed Continuity
M351
Is the inspection result normal? YES >> GO TO 4. NO >> Replace combination switch (spiral cable). Refer to SR-5, "Exploded View".
SRC-58
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016031
D
DTC Display contents of CONSULT-III DRIVER AIRBAG MODULE [SHORT] DTC detecting condition Driver air bag module circuit are shorted to each other (including the spiral cable) Possible cause Disconnection of wiring harness and short Malfunction in driver air bag module Malfunction in spiral cable Malfunction in air bag diagnosis sensor unit
B1052 B1057
Diagnosis Procedure
INFOID:0000000005016032
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-59
2009 Z12
M351
4.
Check continuity between driver air bag module harness connector and ground.
Driver side air bag module Connector M350 Terminal 10 11 12 9 Ground Not existed Continuity
M351
Is the inspection result normal? YES >> GO TO 4. NO >> Replace combination switch (spiral cable). Refer to SR-5, "Exploded View".
SRC-60
2009 Z12
It detects a shock that is more than the specified level and monitors whether the driver and passenger air bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally. It contains the G sensors for both frontal and side collisions and spare battery function in case of main battery damage in collision.
DTC Logic
DTC DETECTION LOGIC
DTC B1058 B1059 B1060 B1061 B1062 B1063 Display contents of CONSULT-III DTC detecting condition
INFOID:0000000005016034
D
Possible cause
CONTROL UNIT
Diagnosis Procedure
INFOID:0000000005016035
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-61
2009 Z12
SRC-62
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016037
D
DTC B1065 B1070 Display contents of CONSULT-III ASSIST A/B MODULE [OPEN] DTC detecting condition Possible cause Disconnection of wiring harness and open Malfunction in passenger air bag module Malfunction in air bag diagnosis sensor unit
SRC
Diagnosis Procedure
INFOID:0000000005016038
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-63
2009 Z12
SRC-64
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016040
D
DTC B1066 B1071 Display contents of CONSULT-III ASSIST A/B MODULE [VB-SHORT] DTC detecting condition Passenger air bag module circuit is shorted to power supply circuit Possible cause Disconnection of wiring harness and short Malfunction in passenger air bag module Malfunction in air bag diagnosis sensor unit
SRC
Diagnosis Procedure
INFOID:0000000005016041
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-65
2009 Z12
SRC-66
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016043
D
DTC B1067 B1072 Display contents of CONSULT-III ASSIST A/B MODULE [GND-SHORT] DTC detecting condition Passenger air bag module circuit is shorted to ground Possible cause Disconnection of wiring harness and short Malfunction in passenger air bag module Malfunction in air bag diagnosis sensor unit
SRC
Diagnosis Procedure
INFOID:0000000005016044
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-67
2009 Z12
SRC-68
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016046
D
DTC B1068 B1073 Display contents of CONSULT-III ASSIST A/B MODULE [SHORT] DTC detecting condition Passenger air bag module circuits are shorted to each other Possible cause Disconnection of wiring harness and short Malfunction in passenger air bag module Malfunction in air bag diagnosis sensor unit
SRC
Diagnosis Procedure
INFOID:0000000005016047
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-69
2009 Z12
SRC-70
2009 Z12
It detects a shock that is more than the specified level and monitors whether the driver and passenger air bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally. It contains the G sensors for both frontal and side collisions and spare battery function in case of main battery damage in collision.
DTC Logic
DTC DETECTION LOGIC
DTC B1074 B1075 B1076 B1077 B1078 B1079 Display contents of CONSULT-III DTC detecting condition
INFOID:0000000005016049
D
Possible cause
CONTROL UNIT
Diagnosis Procedure
INFOID:0000000005016050
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-71
2009 Z12
SRC-72
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016052
D
DTC Display contents of CONSULT-III DRIVER AIRBAG MODULE [SHORT] DTC detecting condition Driver air bag module circuit are shorted to each other (including the spiral cable) Possible cause Disconnection of wiring harness and short Malfunction in driver air bag module Malfunction in spiral cable Malfunction in air bag diagnosis sensor unit
B1080 B1096
Diagnosis Procedure
INFOID:0000000005016053
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-73
2009 Z12
M351
4.
Check continuity between driver air bag module harness connector and ground.
Driver side air bag module Connector M350 Terminal 10 11 12 9 Ground Not existed Continuity
M351
Is the inspection result normal? YES >> GO TO 4. NO >> Replace combination switch (spiral cable). Refer to MWI-97, "Exploded View".
SRC-74
2009 Z12
In the case of a frontal collision that is more than the specified impact level, the air bag diagnosis sensor unit detects the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on passengers chest with load limiter.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016055
D
DTC Display contents of CONSULT-III PRE-TEN FRONT RH [OPEN] DTC detecting condition Possible cause Disconnection of wiring harness and open Malfunction in seat belt pre-tensioner RH Malfunction in air bag diagnosis sensor unit
B1081
SRC
Diagnosis Procedure
INFOID:0000000005016056
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-75
2009 Z12
SRC-76
2009 Z12
In the case of a frontal collision that is more than the specified impact level, the air bag diagnosis sensor unit detects the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on passengers chest with load limiter.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016058
D
DTC Display contents of CONSULT-III PRE-TEN FRONT RH [VB-SHORT] DTC detecting condition Seat belt pre-tensioner RH circuit is shorted to power supply circuit Possible cause Disconnection of wiring harness and short Malfunction in seat belt pre-tensioner RH Malfunction in air bag diagnosis sensor unit
B1082
SRC
Diagnosis Procedure
INFOID:0000000005016059
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-77
2009 Z12
SRC-78
2009 Z12
In the case of a frontal collision that is more than the specified impact level, the air bag diagnosis sensor unit detects the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on passengers chest with load limiter.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016061
D
DTC Display contents of CONSULT-III PRE-TEN FRONT RH [GND-SHORT] DTC detecting condition Seat belt pre-tensioner RH circuit is shorted to ground Possible cause Disconnection of wiring harness and short Malfunction in seat belt pre-tensioner RH Malfunction in air bag diagnosis sensor unit
B1083
SRC
Diagnosis Procedure
INFOID:0000000005016062
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-79
2009 Z12
SRC-80
2009 Z12
In the case of a frontal collision that is more than the specified impact level, the air bag diagnosis sensor unit detects the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on passengers chest with load limiter.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016064
D
DTC Display contents of CONSULT-III PRE-TEN FRONT RH [SHORT] DTC detecting condition Seat belt pre-tensioner RH circuits are shorted to each other Possible cause Disconnection of wiring harness and short Malfunction in seat belt pre-tensioner RH Malfunction in air bag diagnosis sensor unit
B1084
SRC
Diagnosis Procedure
INFOID:0000000005016065
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-81
2009 Z12
SRC-82
2009 Z12
In the case of a frontal collision that is more than the specified impact level, the air bag diagnosis sensor unit detects the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on passengers chest with load limiter.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016067
D
DTC Display contents of CONSULT-III PRE-TEN FRONT LH [OPEN] DTC detecting condition Possible cause Disconnection of wiring harness and open Malfunction in seat belt pre-tensioner LH Malfunction in air bag diagnosis sensor unit
B1086
SRC
Diagnosis Procedure
INFOID:0000000005016068
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-83
2009 Z12
SRC-84
2009 Z12
In the case of a frontal collision that is more than the specified impact level, the air bag diagnosis sensor unit detects the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on passengers chest with load limiter.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016070
D
DTC Display contents of CONSULT-III PRE-TEN FRONT LH [VB-SHORT] DTC detecting condition Seat belt pre-tensioner LH circuit is shorted to power supply circuit Possible cause Disconnection of wiring harness and short Malfunction in seat belt pre-tensioner LH Malfunction in air bag diagnosis sensor unit
B1087
SRC
Diagnosis Procedure
INFOID:0000000005016071
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-85
2009 Z12
SRC-86
2009 Z12
In the case of a frontal collision that is more than the specified impact level, the air bag diagnosis sensor unit detects the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on passengers chest with load limiter.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016073
D
DTC Display contents of CONSULT-III PRE-TEN FRONT LH [GND-SHORT] DTC detecting condition Seat belt pre-tensioner LH circuit is shorted to ground Possible cause Disconnection of wiring harness and short Malfunction in seat belt pre-tensioner LH Malfunction in air bag diagnosis sensor unit
B1088
SRC
Diagnosis Procedure
INFOID:0000000005016074
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-87
2009 Z12
SRC-88
2009 Z12
In the case of a frontal collision that is more than the specified impact level, the air bag diagnosis sensor unit detects the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on passengers chest with load limiter.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016076
D
DTC Display contents of CONSULT-III PRE-TEN FRONT LH [SHORT] DTC detecting condition Seat belt pre-tensioner LH circuits are shorted to each other Possible cause Disconnection of wiring harness and short Malfunction in seat belt pre-tensioner LH Malfunction in air bag diagnosis sensor unit
B1089
SRC
Diagnosis Procedure
INFOID:0000000005016077
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-89
2009 Z12
SRC-90
2009 Z12
It detects a shock that is more than the specified level and monitors whether the driver and passenger air bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally. It contains the G sensors for both frontal and side collisions and spare battery function in case of main battery damage in collision.
DTC Logic
DTC DETECTION LOGIC
DTC B1090 B1091 B1092 B1093 B0194 B1095 Display contents of CONSULT-III DTC detecting condition
INFOID:0000000005016079
D
Possible cause
CONTROL UNIT
Diagnosis Procedure
INFOID:0000000005016080
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-91
2009 Z12
SRC-92
2009 Z12
It detects a shock that is more than the specified level and monitors whether the driver and passenger air bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally. It contains the G sensors for both frontal and side collisions and spare battery function in case of main battery damage in collision.
DTC Logic
DTC DETECTION LOGIC
DTC B1106 B1107 B1108 B1109 B1110 B1111 Display contents of CONSULT-III DTC detecting condition
INFOID:0000000005016082
D
Possible cause
CONTROL UNIT
Diagnosis Procedure
INFOID:0000000005016083
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-93
2009 Z12
SRC-94
2009 Z12
When air bag diagnosis sensor unit defines both signal voltage of the G sensor and the safing algorithm to be that of collision which is more than the specified level, the driving circuit switches on and feeds the electric ignitor of both the front side air bag and side curtain air bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016085
D
DTC B1113 B1114 Display contents of CONSULT-III SATELLITE SENS RH [UNIT FAIL] DTC detecting condition Possible cause Disconnection of wiring harness Malfunction in satellite sensor RH Malfunction in air bag diagnosis sensor unit
SRC
Diagnosis Procedure
INFOID:0000000005016086
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-95
2009 Z12
SRC-96
2009 Z12
When air bag diagnosis sensor unit defines both signal voltage of the G sensor and the safing algorithm to be that of collision which is more than the specified level, the driving circuit switches on and feeds the electric ignitor of both the front side air bag and side curtain air bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016088
D
DTC Display contents of CONSULT-III SATELLITE SENS RH [COMM FAIL] DTC detecting condition Possible cause Disconnection of wiring harness Malfunction in satellite sensor RH Malfunction in air bag diagnosis sensor unit
B1115
SRC
Diagnosis Procedure
INFOID:0000000005016089
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-97
2009 Z12
SRC-98
2009 Z12
When air bag diagnosis sensor unit defines both signal voltage of the G sensor and the safing algorithm to be that of collision which is more than the specified level, the driving circuit switches on and feeds the electric ignitor of both the front side air bag and side curtain air bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005128467
D
DTC B1116 Display contents of CONSULT-III SATELLITE SENS RH [UNMATCH] DTC detecting condition Satellite sensor RH is out of the specified specification Possible cause Diagnosis sensor unit or crash zone sensor is different from the part specified
SRC
Diagnosis Procedure
INFOID:0000000005128468
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-99
2009 Z12
SRC-100
2009 Z12
When air bag diagnosis sensor unit defines both signal voltage of the G sensor and the safing algorithm to be that of collision which is more than the specified level, the driving circuit switches on and feeds the electric ignitor of both the front side air bag and side curtain air bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016091
D
DTC B1118 B1119 Display contents of CONSULT-III SATELLITE SENS LH [UNIT FAIL] DTC detecting condition Possible cause Disconnection of wiring harness Malfunction in satellite sensor LH Malfunction in air bag diagnosis sensor unit
SRC
Diagnosis Procedure
INFOID:0000000005016092
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-101
2009 Z12
SRC-102
2009 Z12
When air bag diagnosis sensor unit defines both signal voltage of the G sensor and the safing algorithm to be that of collision which is more than the specified level, the driving circuit switches on and feeds the electric ignitor of both the front side air bag and side curtain air bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016094
D
DTC Display contents of CONSULT-III SATELLITE SENS LH [COMM FAIL] DTC detecting condition Possible cause Disconnection of wiring harness Malfunction in satellite sensor LH Malfunction in air bag diagnosis sensor unit
B1120
SRC
Diagnosis Procedure
INFOID:0000000005016095
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-103
2009 Z12
SRC-104
2009 Z12
When air bag diagnosis sensor unit defines both signal voltage of the G sensor and the safing algorithm to be that of collision which is more than the specified level, the driving circuit switches on and feeds the electric ignitor of both the front side air bag and side curtain air bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005128486
D
DTC B1121 Display contents of CONSULT-III SATELLITE SENS LH [UNMATCH] DTC detecting condition Satellite sensor LH is out of the specified specification Possible cause Diagnosis sensor unit or crash zone sensor is different from the part specified
SRC
Diagnosis Procedure
J
INFOID:0000000005128487
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-105
2009 Z12
SRC-106
2009 Z12
It detects a shock that is more than the specified level and monitors whether the driver and passenger air bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally. It contains the G sensors for both frontal and side collisions and spare battery function in case of main battery damage in collision.
DTC Logic
DTC DETECTION LOGIC
DTC B1122 B1123 B1124 B1125 B1126 B1127 Display contents of CONSULT-III DTC detecting condition
INFOID:0000000005016097
D
Possible cause
CONTROL UNIT
Diagnosis Procedure
INFOID:0000000005016098
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-107
2009 Z12
SRC-108
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016100
D
DTC Display contents of CONSULT-III SIDE MODULE RH [OPEN] DTC detecting condition Possible cause Disconnection of wiring harness and open Malfunction in side air bag module RH Malfunction in air bag diagnosis sensor unit
B1129
SRC
J
INFOID:0000000005016101
Diagnosis Procedure
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-109
2009 Z12
SRC-110
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016103
D
DTC Display contents of CONSULT-III SIDE MODULE RH [VB-SHORT] DTC detecting condition Side air bag module RH circuit is shorted to power supply circuit Possible cause Disconnection of wiring harness and short Malfunction in side air bag module RH Malfunction in air bag diagnosis sensor unit
B1130
SRC
Diagnosis Procedure
INFOID:0000000005016104
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-111
2009 Z12
SRC-112
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016106
D
DTC Display contents of CONSULT-III SIDE MODULE RH [GND-SHORT] DTC detecting condition Side air bag module RH circuit is shorted to ground Possible cause Disconnection of wiring harness and short Malfunction in side air bag module RH Malfunction in air bag diagnosis sensor unit
B1131
SRC
Diagnosis Procedure
INFOID:0000000005016107
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-113
2009 Z12
SRC-114
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016109
D
DTC Display contents of CONSULT-III SIDE MODULE RH [SHORT] DTC detecting condition Side air bag module RH circuits are shorted to each other Possible cause Disconnection of wiring harness and short Malfunction in side air bag module RH Malfunction in air bag diagnosis sensor unit
B1132
SRC
Diagnosis Procedure
INFOID:0000000005016110
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-115
2009 Z12
SRC-116
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016112
D
DTC Display contents of CONSULT-III SIDE MODULE LH [OPEN] DTC detecting condition Possible cause Disconnection of wiring harness and open Malfunction in side air bag module LH Malfunction in air bag diagnosis sensor unit
B1134
SRC
Diagnosis Procedure
INFOID:0000000005016113
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-117
2009 Z12
SRC-118
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016115
D
DTC Display contents of CONSULT-III SIDE MODULE LH [VB-SHORT] DTC detecting condition Side air bag module LH circuit is shorted to power supply circuit Possible cause Disconnection of wiring harness and short Malfunction in side air bag module LH Malfunction in air bag diagnosis sensor unit
B1135
SRC
Diagnosis Procedure
INFOID:0000000005016116
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-119
2009 Z12
SRC-120
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016118
D
DTC Display contents of CONSULT-III SIDE MODULE LH [GND-SHORT] DTC detecting condition Side air bag module LH circuit is shorted to ground Possible cause Disconnection of wiring harness and short Malfunction in side air bag module LH Malfunction in air bag diagnosis sensor unit
B1136
SRC
Diagnosis Procedure
INFOID:0000000005016119
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-121
2009 Z12
SRC-122
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
INFOID:0000000005016121
D
DTC Display contents of CONSULT-III SIDE MODULE LH [SHORT] DTC detecting condition Side air bag module LH circuits are shorted to each other Possible cause Disconnection of wiring harness and short Malfunction in side air bag module LH Malfunction in air bag diagnosis sensor unit
B1137
SRC
Diagnosis Procedure
INFOID:0000000005016122
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-123
2009 Z12
SRC-124
2009 Z12
It detects a shock that is more than the specified level and monitors whether the driver and passenger air bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally. It contains the G sensors for both frontal and side collisions and spare battery function in case of main battery damage in collision.
DTC Logic
DTC DETECTION LOGIC
DTC B1138 B1139 B1140 B1141 B1142 B1143 Display contents of CONSULT-III DTC detecting condition
INFOID:0000000005016124
D
Possible cause
CONTROL UNIT
Diagnosis Procedure
INFOID:0000000005016125
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-125
2009 Z12
SRC-126
2009 Z12
It detects a shock that is more than the specified level and monitors whether the driver and passenger air bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally. It contains the G sensors for both frontal and side collisions and spare battery function in case of main battery damage in collision.
DTC Logic
DTC DETECTION LOGIC
DTC Display contents of CONSULT-III Diagnosis sensor unit DTC detecting condition Air bag diagnosis sensor unit is malfunctioning or out of the specification Possible cause
INFOID:0000000005016127
E
Malfunction in air bag diagnosis sensor unit Configuration in air bag diagnosis sensor unit does not match the vehicles specification
B1144
Diagnosis Procedure
INFOID:0000000005016128
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-127
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
DTC Display contents of CONSULT-III CURTAIN MODULE RH [OPEN] DTC detecting condition Possible cause
INFOID:0000000005016130
B1145
Disconnection of wiring harness and open Malfunction in side curtain air bag module RH Malfunction in air bag diagnosis sensor unit
Diagnosis Procedure
INFOID:0000000005016131
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-128
2009 Z12
SRC
SRC-129
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
DTC Display contents of CONSULT-III CURTAIN MODULE RH [VB-SHORT] DTC detecting condition Curtain air bag module RH circuit is shorted to power supply circuit Possible cause
INFOID:0000000005016133
B1146
Disconnection of wiring harness and short Malfunction in curtain air bag module RH Malfunction in air bag diagnosis sensor unit
Diagnosis Procedure
INFOID:0000000005016134
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-130
2009 Z12
SRC
SRC-131
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
DTC Display contents of CONSULT-III CURTAIN MODULE RH [GND-SHORT] DTC detecting condition Curtain air bag module RH circuit is shorted to ground Possible cause
INFOID:0000000005016136
B1147
Disconnection of wiring harness and short Malfunction in curtain air bag module RH Malfunction in air bag diagnosis sensor unit
Diagnosis Procedure
INFOID:0000000005016137
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-132
2009 Z12
SRC
SRC-133
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
DTC Display contents of CONSULT-III CURTAIN MODULE RH [SHORT] DTC detecting condition Curtain air bag module RH circuits are shorted to each other Possible cause
INFOID:0000000005016139
B1148
Disconnection of wiring harness and short Malfunction in curtain air bag module RH Malfunction in air bag diagnosis sensor unit
Diagnosis Procedure
INFOID:0000000005016140
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-134
2009 Z12
SRC
SRC-135
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
DTC Display contents of CONSULT-III CURTAIN MODULE LH [OPEN] DTC detecting condition Possible cause
INFOID:0000000005016142
B1150
Disconnection of wiring harness and open Malfunction in curtain air bag module LH Malfunction in air bag diagnosis sensor unit
Diagnosis Procedure
INFOID:0000000005016143
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-136
2009 Z12
SRC
SRC-137
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
DTC Display contents of CONSULT-III CURTAIN MODULE LH [VB-SHORT] DTC detecting condition Curtain air bag module LH circuit is shorted to power supply circuit Possible cause
INFOID:0000000005016145
B1151
Disconnection of wiring harness and short Malfunction in curtain air bag module LH Malfunction in air bag diagnosis sensor unit
Diagnosis Procedure
INFOID:0000000005016146
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-138
2009 Z12
SRC
SRC-139
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
DTC Display contents of CONSULT-III CURTAIN MODULE LH [GND-SHORT] DTC detecting condition Curtain air bag module LH circuit is shorted to ground Possible cause
INFOID:0000000005016148
B1152
Disconnection of wiring harness and short Malfunction in curtain air bag module LH Malfunction in air bag diagnosis sensor unit
Diagnosis Procedure
INFOID:0000000005016149
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-140
2009 Z12
SRC
SRC-141
2009 Z12
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction. This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic
DTC DETECTION LOGIC
DTC Display contents of CONSULT-III CURTAIN MODULE LH [SHORT] DTC detecting condition Curtain air bag module LH circuits are shorted to each other Possible cause
INFOID:0000000005016151
B1153
Disconnection of wiring harness and short Malfunction in curtain air bag module LH Malfunction in air bag diagnosis sensor unit
Diagnosis Procedure
INFOID:0000000005016152
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-142
2009 Z12
SRC
SRC-143
2009 Z12
It detects a shock that is more than the specified level and monitors whether the driver and passenger air bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally. It contains the G sensors for both frontal and side collisions and spare battery function in case of main battery damage in collision.
DTC Logic
DTC DETECTION LOGIC
DTC B1154 B1155 B1156 B1157 B1158 B1159 Display contents of CONSULT-III DTC detecting condition
INFOID:0000000005016154
Possible cause
CONTROL UNIT
Diagnosis Procedure
INFOID:0000000005016155
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-144
2009 Z12
SRC
SRC-145
2009 Z12
It detects a shock that is more than the specified level and monitors whether the driver and passenger air bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally. It contains the G sensors for both frontal and side collisions and spare battery function in case of main battery damage in collision.
DTC Logic
DTC DETECTION LOGIC
DTC B1170 B1171 B1172 B1173 B1174 B1175 Display contents of CONSULT-III DTC detecting condition
INFOID:0000000005016157
Possible cause
CONTROL UNIT
Diagnosis Procedure
INFOID:0000000005016158
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-146
2009 Z12
SRC
SRC-147
2009 Z12
It detects a shock that is more than the specified level and monitors whether the driver and passenger air bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally. It contains the G sensors for both frontal and side collisions and spare battery function in case of main battery damage in collision.
DTC Logic
DTC DETECTION LOGIC
DTC B1186 B1187 B1188 B1189 B1190 B1191 Display contents of CONSULT-III DTC detecting condition
INFOID:0000000005016160
Possible cause
CONTROL UNIT
Diagnosis Procedure
INFOID:0000000005016161
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-148
2009 Z12
SRC
SRC-149
2009 Z12
It detects a shock that is more than the specified level and monitors whether the driver and passenger air bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally. It contains the G sensors for both frontal and side collisions and spare battery function in case of main battery damage in collision.
DTC Logic
DTC DETECTION LOGIC
DTC B1202 B1203 B1204 B1205 B1206 B1207 Display contents of CONSULT-III DTC detecting condition
INFOID:0000000005016163
Possible cause
CONTROL UNIT
Diagnosis Procedure
INFOID:0000000005016164
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-150
2009 Z12
SRC
SRC-151
2009 Z12
The air bags and seat belt pre-tensioners for driver and passenger are activated by the air bag diagnosis sensor unit signal transmitted at the time of the frontal collision.
DTC Logic
DTC DETECTION LOGIC
DTC B1209 Display contents of CONSULT-III FRONTAL COLLISION DETECTION DTC detecting condition Seat belt pre-tensioner, driver side air bag and passenger air bag are deployed
INFOID:0000000005016166
Possible cause
Diagnosis Procedure
INFOID:0000000005016167
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-152
2009 Z12
5.FINAL CHECK
Perform AIR BAG Self Diagnostic Result with CONSULT-III and air bag warning lamp status. Is the inspection result normal? YES >> INSPECTION END NO >> Check intermittent incident. Refer to GI-34, "Intermittent Incident".
SRC
SRC-153
2009 Z12
The side air bag and curtain air bag are activated by the air bag diagnosis sensor unit signal transmitted at the time of side collision.
DTC Logic
DTC DETECTION LOGIC
DTC B1210 Display contents of CONSULT-III SIDE COLLISION DETECTION DTC detecting condition Side air bag and curtain air bag are deployed
INFOID:0000000005016169
Possible cause
Diagnosis Procedure
INFOID:0000000005016170
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor) Never use unspecified tester or other measuring device.
1.CHECK SIDE AIR BAG MODULE AND CURTAIN AIR BAG MODULE
Check whether or not side air bag module or curtain air bag module is activated in the past. Is activation detected? YES >> Replace side air bag module, curtain air bag module, air bag diagnosis sensor unit, and satelite sensor. Refer to SE-11, "Exploded View" (side air bag module), SR-14, "Exploded View" (curtain air bag module), SR-18, "Exploded View" (satelite sensor), SR-20, "Exploded View" (air bag diagnosis sensor unit). NO >> GO TO 2
SRC-154
2009 Z12
4.FINAL CHECK
Perform AIR BAG Self Diagnostic Result with CONSULT-III and air bag warning lamp status. Is the inspection result normal? YES >> INSPECTION END NO >> Check intermittent incident. Refer to GI-34, "Intermittent Incident".
SRC
SRC-155
2009 Z12
The seat belt pre-tensioner and curtain air bag are activated by the air bag diagnosis sensor unit signal at the time of rollover.
DTC Logic
DTC DETECTION LOGIC
DTC B1211 Display contents of CONSULT-III ROLLOVER DETECTION DTC detecting condition Seat belt pre-tensioner and curtain air bag module are deployed because of rollover detection
INFOID:0000000005016172
Possible cause
Diagnosis Procedure
INFOID:0000000005016173
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor) Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
SRC-156
2009 Z12
4.FINAL CHECK
Perform AIR BAG Self Diagnostic Result with CONSULT-III and/or air bag warning lamp status. Is the inspection result normal? YES >> INSPECTION END NO >> Check the intermittent incident. Refer to GI-34, "Intermittent Incident".
SRC
SRC-157
2009 Z12
Satellite sensor is a G sensor that outputs voltage signal during deceleration at the time of a vehicle side collision that is more than the specified limit is detected.
DTC Logic
DTC DETECTION LOGIC
DTC B1212 B1213 B1214 Display contents of CONSULT-III RH1 SAT-SENS DTC detecting condition Possible cause
INFOID:0000000005016175
Disconnection of wiring harness Malfunction in satellite sensor RH Malfunction in air bag diagnosis sensor unit
Diagnosis Procedure
INFOID:0000000005016176
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-158
2009 Z12
SRC
SRC-159
2009 Z12
Satellite sensor is a G sensor that outputs voltage signal during deceleration at the time of a vehicle side collision that is more than the specified limit is detected.
DTC Logic
DTC DETECTION LOGIC
DTC B1215 B1216 B1217 Display contents of CONSULT-III LH1 SAT-SENS DTC detecting condition Possible cause
INFOID:0000000005016178
Disconnection of wiring harness Malfunction in satellite sensor LH Malfunction in air bag diagnosis sensor unit
Diagnosis Procedure
INFOID:0000000005016179
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-160
2009 Z12
SRC
SRC-161
2009 Z12
It detects a shock that is more than the specified level and monitors whether the driver and passenger air bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally. It contains the G sensors for both frontal and side collisions and spare battery function in case of main battery damage in collision.
DTC Logic
DTC DETECTION LOGIC
DTC B1218 B1219 B1220 B1221 B1222 B1223 Display contents of CONSULT-III DTC detecting condition
INFOID:0000000005016181
Possible cause
CONTROL UNIT
Diagnosis Procedure
INFOID:0000000005016182
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-162
2009 Z12
SRC
SRC-163
2009 Z12
It detects a shock that is more than the specified level and monitors whether the driver and passenger air bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally. It contains the G sensors for both frontal and side collisions and spare battery function in case of main battery damage in collision.
DTC Logic
DTC DETECTION LOGIC
DTC B1239 Display contents of CONSULT-III CONTROL UNIT DTC detecting condition Air bag diagnosis sensor unit is malfunctioning
INFOID:0000000005096282
Diagnosis Procedure
INFOID:0000000005096283
WARNING: Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more. (To discharge backup capacitor.) Never use unspecified tester or other measuring device.
SRC-164
2009 Z12
Reference page SRC-23, "CONSULT-III Function". SRC-17, "Diagnosis with Air Bag Warning Lamp", SRC-23, "CONSULT-III Function". GI-34, "Intermittent Incident" SRC-25, "DTC Logic". SRC-27, "DTC Logic". SRC-29, "DTC Logic". SRC-31, "DTC Logic". SRC-33, "DTC Logic".
NO DTC IS DETECTED.
B1001-B1015
CONTROL UNIT
SRC
OCCUPANT SENS C/U [UNIT FAIL] OCCUPANT SENS [UNIT FAIL] OCCUPANT SENS C/U [COMM FAIL] PASS A/B INDCTR CKT
Malfunction occurs in Occupant Detection System sensor Malfunction occurs in Occupant Detection System control unit, circuit of Occupant Detection System control unit air bag diagnosis sensor unit, or air bag diagnosis sensor unit Passenger air bag OFF indicator circuit is open or shorted to ground or the circuits are shorted each other Malfunction occurs in Occupant Detection System control unit, circuit of Occupant Detection System control unit air bag diagnosis sensor unit, or air bag diagnosis sensor unit Air bag diagnosis sensor unit is malfunctioning or out of the specified specification Crash zone sensor is malfunctioning Crash zone sensor is malfunctioning Crash zone sensor is out of the specified specification
J
SRC-35, "DTC Logic". SRC-37, "DTC Logic". SRC-39, "DTC Logic". SRC-41, "DTC Logic". SRC-43, "DTC Logic". SRC-45, "DTC Logic". SRC-47, "DTC Logic". SRC-49, "DTC Logic". SRC-51, "DTC Logic". SRC-53, "DTC Logic". SRC-55, "DTC Logic".
B1022
B1023 B1025 B1032 B1048 B1026-B1031 B1033 B1034 B1035 B1036 B1037 B1039 B1041 B1042-B1047 B1049 B1054 B1050 B1055
OCS SENSOR
CONTROL UNIT CRASH ZONE SEN [UNIT FAIL] CRASH ZONE SEN [COMM FAIL] CRASH ZONE SEN [UNMATCH] CRASH ZONE SEN1
CONTROL UNIT DRIVER AIRBAG MODULE [OPEN] DRIVER AIRBAG MODULE [VB-SHORT]
Air bag diagnosis sensor unit is malfunctioning Driver air bag module circuit is open (including the spiral cable) Driver air bag module circuit is shorted to power supply circuit (including the spiral cable)
SRC-165
2009 Z12
SRC-166
2009 Z12
SRC
SRC-167
2009 Z12
SRC-168
2009 Z12
INFOID:0000000005016184
SRC
JCHWM0433GB
SRC-169
2009 Z12
JCHWM0434GB
SRC-170
2009 Z12
SRC
O
JCHWM0435GB
SRC-171
2009 Z12
JCHWM0436GB
SRC-172
2009 Z12
SRC
O
JCHWM0437GB
SRC-173
2009 Z12
JCHWM0438GB
SRC-174
2009 Z12
SYMPTOM DIAGNOSIS
SRS AIR BAG WARNING LAMP DOES NOT TURN OFF
Diagnosis Procedure
INFOID:0000000005016347
SRC
SRC-175
2009 Z12
SRC-176
2009 Z12
PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
INFOID:0000000005153086
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. Information necessary to service the system safely is included in the SRS AIR BAG and SEAT BELT of this Service Manual. WARNING: To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer. Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the SRS AIR BAG. Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.
SRC
Service
INFOID:0000000005153087
Never use electrical test equipment to check SRS circuits unless instructed to in this Service Manual. Before servicing the SRS, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes or more. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pretensioner to deploy. Therefore, never work on any SRS connectors or wires until at least 3 minutes have passed. Diagnosis sensor unit must always be installed with their arrow marks pointing towards the front of the vehicle for proper operation. Also check diagnosis sensor unit for cracks, deformities or rust before installation and replace as required. The spiral cable must be aligned with the neutral position since its rotations are limited. Never turn steering wheel and column after removal of steering gear. Handle air bag module carefully. Always place driver and front passenger air bag modules with the pad side facing upward and seat mounted front side air bag module standing with the stud bolt side facing down. Conduct self-diagnosis to check entire SRS for proper function after replacing any components. After air bag inflates, the front instrument panel assembly should be replaced if damaged. Always replace instrument panel pad following front passenger air bag deployment. Never solder the harness when making repairs. Check that harness is not pinched and that there is no contact with other components. Never allow harness to come in contact with oil, grease, waste oil, or water. Never insert foreign materials, such as a screwdriver, into the harness connector. (This is to prevent accidental activation caused by static electricity.) Always use CONSULT-III or SRS air bag warning lamp to perform the circuit diagnosis. (Never use an electric tester such as a circuit tester.)
SRC-177
2009 Z12
PRECAUTIONS
< PRECAUTION >
INFOID:0000000005016189
Replace Occupant Detection System control unit and passenger front seat cushion frame as an assembly. Refer to SE-11, "Exploded View".
SRC-178
2009 Z12