Professional Documents
Culture Documents
Srs Airbag Control System: Section
Srs Airbag Control System: Section
E
CONTENTS
BASIC INSPECTION .................................... 6 DTC/CIRCUIT DIAGNOSIS ......................... 26 F
DIAGNOSIS AND REPAIR WORK FLOW ......... 6 B1001, B1002, B1003, B1004, B1005 DIAG-
Work Flow ................................................................. 6 NOSIS SENSOR UNIT ...................................... 26 G
Description ...............................................................26
INSPECTION AND ADJUSTMENT ..................... 9 DTC Logic ................................................................26
ADDITIONAL SERVICE WHEN REPLACING Diagnosis Procedure ...............................................26
SRC
CONTROL UNIT .......................................................... 9 B1006, B1007, B1008, B1009, B1010 DIAG-
ADDITIONAL SERVICE WHEN REPLACING
NOSIS SENSOR UNIT ...................................... 28
CONTROL UNIT : Description .................................. 9
Description ...............................................................28 I
ADDITIONAL SERVICE WHEN REPLACING
DTC Logic ................................................................28
CONTROL UNIT : Special Repair Requirement ...... 9
Diagnosis Procedure ...............................................28
ZERO POINT RESET .................................................. 9 J
ZERO POINT RESET : Description .......................... 9
B1011, B1012, B1013, B1014, B1015 DIAG-
ZERO POINT RESET : Special Repair Require- NOSIS SENSOR UNIT ...................................... 30
ment .......................................................................... 9 Description ...............................................................30
DTC Logic ................................................................30 K
SYSTEM DESCRIPTION ............................. 11 Diagnosis Procedure ...............................................30
SRS AIR BAG SYSTEM .....................................11 B1017, B1020, B1021 OCCUPANT SYSTEM L
System Diagram ...................................................... 11 CONTROL UNIT ................................................ 32
System Description ................................................. 11 Description ...............................................................32
Component Parts Location ...................................... 13 DTC Logic ................................................................32
M
Component Description ........................................... 14 Diagnosis Procedure ...............................................32
B1120 SATELLITE SENSOR LH ..................... 104 B1144 DIAGNOSIS SENSOR UNIT ............... 128
Description ............................................................ 104 Description ............................................................. 128 P
DTC Logic ............................................................. 104 DTC Logic .............................................................. 128
Diagnosis Procedure ............................................. 104 Diagnosis Procedure ............................................. 128
B1121 SATELLITE SENSOR LH ..................... 106 B1145 CURTAIN AIR BAG MODULE RH ...... 129
Description ............................................................ 106 Description ............................................................. 129
DTC Logic ............................................................. 106 DTC Logic .............................................................. 129
Diagnosis Procedure ............................................. 106 Diagnosis Procedure ............................................. 129
SRC
OVERALL SEQUENCE
JMHIA1324GB
DETAILED FLOW
>> GO TO 3. D
3.CHECK WARNING LAMP OPERATION
Check air bag warning lamp operation in the user mode. Refer to SRC-18, "Diagnosis with Air Bag Warning
Lamp". E
Are any malfunction detected?
YES >> GO TO 5.
NO >> GO TO 4. F
4.CHECK LOW VOLTAGE
Check low voltage with CONSULT. Refer to SRC-24, "CONSULT Function". G
Are any malfunction detected?
YES >> GO TO 9.
NO >> Check intermittent incident. Refer to GI-40, "Intermittent Incident". SRC
5.CHECK SELF DIAGNOSTIC RESULTS
Check self diagnostic result with CONSULT or diagnosis mode.
If it is impossible to switch to diagnosis mode, follow the same procedure that DTC is not detected. I
NOTE:
Perform the following procedure if DTC is detected.
• Record DTC (Print them out with CONSULT.) J
• Erase self diagnostic result.
• Study the relationship between the malfunction that DTC or air bag warning lamp indicates and the symptom
that the customer describes.
• Check related service bulletins for information. K
Is DTC detected?
YES >> GO TO 6.
L
NO >> GO TO 7.
6.PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC CONFIRMATION PROCEDURE for the DTC. M
>> GO TO 8.
N
7.PERFORM DIAGNOSIS ACCORDING TO WARNING LAMP OPERATION
1. Check air bag warning lamp operation in the user mode. Refer to SRC-18, "Diagnosis with Air Bag Warn-
ing Lamp". O
2. Perform Diagnosis Procedure for the air bag warning lamp operation. Refer to SRC-18, "Diagnosis with
Air Bag Warning Lamp" (USER MODE).
P
>> GO TO 9.
8.DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE
Inspect according to Diagnostic Procedure of the DTC.
>> GO TO 9.
>> GO TO 10.
10.FINAL CHECK
Check self diagnostic result and air bag warning lamp operation in the user mode.
Is the malfunction repaired?
YES >> INSPECTION END
NO >> GO TO 2.
When replacing or removing and installing passenger seat, always perform zero point reset so that Occupant
Detection System is activated normally.
C
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement INFOID:0000000009946082
D
WORK PROCEDURE WHEN REPLACING CONTROL UNIT
1.PERFORM ZERO POINT RESET E
Perform zero point reset. Refer to SRC-9, "ZERO POINT RESET : Special Repair Requirement".
>> END F
ZERO POINT RESET
ZERO POINT RESET : Description INFOID:0000000009946083
G
Zero point reset is an initializing procedure for occupant detection sensor that must be performed when replac-
ing or removing and installing passenger seat.
If zero point reset is not performed, the initialization is incomplete and Occupant Detection System does not SRC
operate normally.
NOTE:
• When replacing passenger seat with a NISSAN genuine part, air bag warning lamp blinks if zero point reset I
is incomplete.
• When zero point reset is performed once after removal and installation of passenger seat, CONSULT dis-
plays “complete” and air bag warning does not blink.
• When reinstalling passenger seat after removal, the initial value for occupant detection sensor changes, and J
Occupant Detection System does not operate normally.
• Always perform zero point reset after performing the work as per the following.
- Reinstallation of passenger seat K
- Replacement of passenger seat with a seat that is zero point reset complete.
ZERO POINT RESET : Special Repair Requirement INFOID:0000000009946084
L
1.PERFORM ZERO POINT RESET
1. Perform zero point reset.
NOTE: M
When performing zero point reset, be careful of the items described as per the following.
• Perform zero point reset after installing passenger seat to the vehicle
• Do not put any objects on passenger seat N
• Do not apply excessive vibration to the vehicle
• Do not touch the vehicle
• Do not tilt the vehicle
2. Select start on “Zero point reset function” screen from, WORK SUPPORT of CONSULT “OCCUPANT O
DETECTION”.
3. “Zero point reset” starts.
P
>> GO TO 2.
2.CONFIRMATION OF SETTING
1. Proceed to “Zero point reset function” screen from work support of CONSULT “OCCUPANT DETEC-
TION”.
2. Check that “Complete” or “Incomplete” is displayed on “Zero point reset status”.
CAUTION:
SRC
JMHIA1078GB
N
System Description INFOID:0000000009946086
Supplemental Restraint System (SRS) activates air bag module and seal belt pre-tensioner when it detects a O
frontal collision or a side collision that is more than the specified limit. Together with other safety devices, it
reduces the impact that occupant receives when vehicle collision occurs.
Air bag diagnosis sensor unit supplies power supply to air bag module and pre-tensioner seat belt when decel-
P
eration that is more than the specified limit is detected by G sensor in air bag diagnosis sensor unit, crash
zone sensor, or satellite sensor. Air bag module is composed of electric igniter (squib), filter, pyrotechnic mate-
rial, and gas generating material. When air bag module receives a signal from air bag diagnosis sensor unit,
air bag module ignites pyrotechnic material using electric igniter (squib) so that gas generating material gener-
ates high temperature nitrogen gas. The gas through filter activates air bag. At the same time, pre-tensioner
seat belt receives power supply from air bag diagnosis sensor unit, gasgenerator is activated, and then gas is
generated. Balls in pipe are moved according to generated gas pressure and strike pinion gear on ELR shaft.
ELR shaft rotates and retracts seat belt.
SRC
JMHIA1080ZZ O
1. Curtain air bag module LH/RH 2. Seat belt pre-tensioner LH/RH 3. Satellite sensor LH/RH
4. Air bag diagnosis sensor unit 5. Occupant Detection System seat 6. Occupant Detection System control P
sensor unit
7. Passenger air bag module 8. Crash zone sensor 9. Passenger air bag OFF indicator
10. Combination meter 11. Combination switch (spiral cable) 12. Driver air bag module
Refer to MWI-8, "METER SYSTEM :
Component Parts Location"
13. Seat belt buckle switch (Driver side/
Passenger side)
Component Function
Detects a collision and supplies power supply for deployment to air bag module and
Air bag diagnosis sensor unit
pre-tensioner seat belt.
Air bag module
• Driver
• Passenger Receives signal from air bag diagnosis sensor unit and deploys air bag.
• Side
• Curtain
Receives signal from air bag diagnosis sensor unit and deploys seat belt pre-tension-
Seat belt pre-tensioner
er.
Seat belt buckle switch Controls deployment timing based on seat belt fastened or unfastened condition.
Crash zone sensor Transmits signal to air bag diagnosis sensor unit when a frontal collision occurs.
Satellite sensor (LH/RH) Transmits signal to air bag diagnosis sensor unit when a side collision occurs.
Detects passenger seat occupant and judges whether or not passenger seat air bag
Occupant Detection System control unit
is deployed.
Indicates air bag malfunctioning and deployment by blinking and illuminating air bag
Combination meter (air bag warning lamp)
warning lamp.
Indicates whether or not passenger air bag is in the activation mode based on the
Passenger air bag OFF indicator
judgement of Occupant Detection System.
Combination switch (spiral cable) Supplies power supply to driver air bag module on steering wheel.
G
JMHIA1079GB
Status (passenger seat) Passenger air bag Passenger air bag OFF in- Air bag warning lamp
dicator
M
Empty Suppress OFF OFF
An object Suppress ON OFF
Child/ child-seat Suppress ON OFF N
Adult Enable to deploy OFF OFF
Malfunction Suppress ON Blinking
O
Zero point reset
Not yet performed (NISSAN Suppress ON Blinking
genuine parts only)
P
JMHIA1080ZZ
1. Curtain air bag module LH/RH 2. Seat belt pre-tensioner LH/RH 3. Satellite sensor LH/RH
4. Air bag diagnosis sensor unit 5. Occupant Detection System seat 6. Occupant Detection System control
sensor unit
7. Passenger air bag module 8. Crash zone sensor 9. Passenger air bag OFF indicator
10. Combination meter 11. Combination switch (spiral cable) 12. Driver air bag module
Refer to MWI-8, "METER SYSTEM :
Component Parts Location"
13. Seat belt buckle switch (Driver side/
Passenger side)
SRC
CAUTION:
• Never use electrical test equipment on any circuit related to the SRS unless instructed in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
• Never repair, splice or modify the SRS wiring harness. If the harness is damaged, replace it with a
new one.
• Keep ground portion clean.
DIAGNOSIS FUNCTION
• The SRS self-diagnosis results can be read with air bag warning lamp and/or CONSULT.
• The user mode is exclusively prepared for the customer (driver). This mode warns the driver of a system
malfunction through the operation of the air bag warning lamp.
• The diagnosis mode allows the technician to locate and inspect the malfunctioning part.
• The mode applications for the air bag warning lamp and CONSULT are as per the following items.
×: Application, —: Not application
Diagnosis tool User mode Diagnosis mode
Air bag warning lamp × ×
CONSULT – ×
Air bag warning lamp operation (user mode) SRS condition Reference item A
• No malfunction is detected
—
• No further action is necessary C
D
SHIA0011E
SHIA0014E O
DIAGNOSIS MODE
The diagnosis mode can only be switched when a malfunction is detected in the user mode. Malfunctioning
P
system is indicated according to blinking pattern of air bag warning lamp.
How to Read Air Bag Warning Lamp
1. Follow the procedures of “PROCEDURE TO CHANGE DIAGNOSIS MODE”, and switch to the diagnosis
mode.
2. Turn ignition switch ON. Check the blinking pattern of air bag warning lamp.
There are 2 blinking patterns for the air bag warning lamp as per the following items.
• Front air bag system: 3 second blink followed by a 0.5 second blink repeated.
JMHIA0945GB
O
Single System Malfunction
• Front air bag system
P
JMHIA0946GB
JMHIA0948GB
JMHIA0947GB
JMHIA0949GB
JMHIA0950GB
SRC
APPLICATION ITEM
CONSULT performs the following functions.
SRC
• It detects a shock that is more than the specified level and monitors whether the driver and passenger air
bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally.
• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
DTC Logic INFOID:0000000009946098
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
B1001
B1002
B1003 CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning Malfunction in air bag diagnosis sensor unit
B1004
B1005
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
SRC
• It detects a shock that is more than the specified level and monitors whether the driver and passenger air
bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally.
• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
DTC Logic INFOID:0000000009946101
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
B1006
B1007
B1008 CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning Malfunction in air bag diagnosis sensor unit
B1009
B1010
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View"
2. Perform DTC confirmation procedure. Refer to SRC-28, "DTC Logic"
Is DTC detected?
SRC
• It detects a shock that is more than the specified level and monitors whether the driver and passenger air
bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally.
• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
DTC Logic INFOID:0000000009946104
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
B1011
B1012
B1013 CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning Malfunction in air bag diagnosis sensor unit
B1014
B1015
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View"
2. Perform DTC confirmation procedure. Refer to SRC-30, "DTC Logic"
Is DTC detected?
SRC
This unit classifies occupant in passenger seat and detects electrical malfunctions in Occupant Detection Sys-
tem, and transmits malfunction information to air bag diagnosis sensor unit.
DTC Logic INFOID:0000000009946107
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness
B1017
OCCUPANT SENS C/U Occupant Detection System control unit • Malfunction in Occupant Detection System con-
B1020
[UNIT FAIL] is malfunctioning trol unit
B1021
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE OCCUPANT DETECTION SYSTEM CONTROL UNIT
1. Replace occupant detection system control unit. Refer to SR-29, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-32, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
SRC
Occupant Detection System sensor detects occupant in passenger seat and transmits it to Occupant Detec-
tion System control unit.
DTC Logic INFOID:0000000009946110
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness
OCCUPANT SENS Occupant Detection System sen- • Malfunction in Occupant Detection System sensor
B1018
[UNIT FAIL] sor is malfunctioning • Malfunction in Occupant Detection System control unit
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE OCCUPANT DETECTION SYSTEM CONTROL UNIT
1. Replace occupant detection system control unit. Refer to SR-29, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-34, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
SRC
This unit classifies occupant in passenger seat and detects electrical malfunctions in Occupant Detection Sys-
tem, and transmits malfunction information to air bag diagnosis sensor unit.
DTC Logic INFOID:0000000009946113
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Internal malfunction of Occupant Detec-
tion System control unit
• Disconnection of wiring harness
• Malfunction of circuit between Occupant
OCCUPANT SENS C/U • Malfunction in Occupant Detection System con-
B1022 Detection System control unit and Air
[COMM FAIL] trol unit
bag diagnosis sensor unit
• Malfunction in air bag diagnosis sensor unit
• Malfunction of Air bag diagnosis sensor
unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE OCCUPANT DETECTION SYSTEM CONTROL UNIT
1. Replace occupant detection system control unit. Refer to SR-29, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-36, "DTC Logic".
SRC
Illuminates passenger air bag OFF indicator when the passenger seat is empty or occupied by a child or a
child-seat.
DTC Logic INFOID:0000000009946116
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
Passenger air bag OFF indicator circuit • Disconnection of wiring harness
PASS A/B INDCTR CKT
B1023 is open or shorted to ground or the cir- • Malfunction in passenger air bag OFF indicator
[UNIT FAIL]
cuits are shorted each other • Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.CHECK PASSENGER AIR BAG OFF INDICATOR
1. Replace passenger air bag OFF indicator. Refer to IP-13, "Exploded View"
2. Perform DTC confirmation procedure. Refer to SRC-38, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
Occupant Detection System sensor detects occupant in passenger seat and transmits it to Occupant Detec-
tion System control unit.
DTC Logic INFOID:0000000009946119
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Internal malfunction of Occupant Detec-
tion System control unit
• Disconnection of wiring harness
B1025 • Malfunction of circuit between Occupant
• Malfunction in Occupant Detection System
B1032 OCS SENSOR Detection System control unit and Air
control unit
B1048 bag diagnosis sensor unit
• Malfunction in air bag diagnosis sensor unit
• Malfunction of Air bag diagnosis sensor
unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE OCCUPANT DETECTION SYSTEM CONTROL UNIT
1. Replace occupant detection system control unit. Refer to SR-29, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-40, "DTC Logic".
SRC
• It detects a shock that is more than the specified level and monitors whether the driver and passenger air
bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally.
• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
DTC Logic INFOID:0000000009946122
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
B1026
B1027
B1028
CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning Malfunction in air bag diagnosis sensor unit
B1029
B1030
B1031
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-42, "DTC Logic".
SRC
Crash zone sensor is a G sensor that outputs voltage signal during deceleration at the time of a vehicle frontal
collision that is more than the specified limit is detected.
DTC Logic INFOID:0000000009946125
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness
B1033 CRASH ZONE SENSOR
Crash zone sensor is malfunctioning • Malfunction in crash zone sensor
B1034 [UNIT FAIL]
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE CRASH ZONE SENSOR
1. Replace crash zone sensor. Refer to SR-22, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-44, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
Revision: 2013 October SRC-44 2014 CUBE
B1033, B1034 CRASH ZONE SENSOR
< DTC/CIRCUIT DIAGNOSIS >
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-44, "DTC Logic". A
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END B
SRC
Crash zone sensor is a G sensor that outputs voltage signal during deceleration at the time of a vehicle frontal
collision that is more than the specified limit is detected.
DTC Logic INFOID:0000000009946128
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
CRASH ZONE SEN- • Disconnection of wiring harness
B1035 SOR Crash zone sensor is malfunctioning • Malfunction in crash zone sensor
[COMM FAIL] • Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE CRASH ZONE SENSOR
1. Replace crash zone sensor. Refer to SR-22, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-46, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
Revision: 2013 October SRC-46 2014 CUBE
B1035 CRASH ZONE SENSOR
< DTC/CIRCUIT DIAGNOSIS >
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-46, "DTC Logic". A
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END B
SRC
Crash zone sensor is a G sensor that outputs voltage signal during deceleration at the time of a vehicle frontal
collision that is more than the specified limit is detected.
DTC Logic INFOID:0000000009946131
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
CRASH ZONE SEN-
Crash zone sensor is out of the speci- Diagnosis sensor unit or crash zone sensor is differ-
B1036 SOR
fied specification ent from the part specified
[UNMATCH]
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE CRASH ZONE SENSOR
1. Replace crash zone sensor. Refer to SR-22, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-48, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
Revision: 2013 October SRC-48 2014 CUBE
B1036 CRASH ZONE SENSOR
< DTC/CIRCUIT DIAGNOSIS >
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-48, "DTC Logic". A
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END B
SRC
Crash zone sensor is a G sensor that outputs voltage signal during deceleration at the time of a vehicle frontal
collision that is more than the specified limit is detected.
DTC Logic INFOID:0000000009946134
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
B1037 • Disconnection of wiring harness
CRASH ZONE
B1039 Crash zone sensor is malfunctioning • Malfunction in crash zone sensor
SENSOR1
B1041 • Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE CRASH ZONE SENSOR
1. Replace crash zone sensor. Refer to SR-22, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-50, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
Revision: 2013 October SRC-50 2014 CUBE
B1037, B1039, B1041 CRASH ZONE SENSOR
< DTC/CIRCUIT DIAGNOSIS >
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-50, "DTC Logic". A
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END B
SRC
• It detects a shock that is more than the specified level and monitors whether the driver and passenger air
bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally.
• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
DTC Logic INFOID:0000000009946137
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
B1042
B1043
B1044
CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning Malfunction in air bag diagnosis sensor unit
B1045
B1046
B1047
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-52, "DTC Logic".
SRC
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946140
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and open
DRIVER AIRBAG
B1049 Driver air bag module circuit is open • Malfunction in driver air bag module
MODULE
B1054 (including the spiral cable) • Malfunction in spiral cable
[OPEN]
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.CHECK SPIRAL CABLE CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver air bag module connector and combination switch (spiral cable) connector.
3. Check continuity between driver air bag module harness connector and combination switch (spiral cable)
harness connector.
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946143
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and short
DRIVER AIRBAG Driver air bag module circuit is shorted to
B1050 • Malfunction in driver air bag module
MODULE power supply circuit
B1055 • Malfunction in spiral cable
[VB-SHORT] (including the spiral cable)
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.CHECK SPIRAL CABLE CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver air bag module connector and combination switch (spiral cable) connector.
3. Check continuity between driver air bag module harness connector and combination switch (spiral cable)
harness connector.
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946146
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and short
DRIVER AIRBAG
B1051 Driver air bag module circuit is shorted to ground • Malfunction in driver air bag module
MODULE
B1056 (including the spiral cable) • Malfunction in spiral cable
[GND-SHORT]
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.CHECK SPIRAL CABLE CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver air bag module connector and combination switch (spiral cable) connector.
3. Check continuity between driver air bag module harness connector and combination switch (spiral cable)
harness connector.
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946149
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and short
DRIVER AIRBAG Driver air bag module circuit are shorted to each
B1052 • Malfunction in driver air bag module
MODULE other
B1057 • Malfunction in spiral cable
[SHORT] (including the spiral cable)
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.CHECK SPIRAL CABLE CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver air bag module connector and combination switch (spiral cable) connector.
3. Check continuity between driver air bag module harness connector and combination switch (spiral cable)
harness connector.
• It detects a shock that is more than the specified level and monitors whether the driver and passenger air
bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally.
• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
DTC Logic INFOID:0000000009946152
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
B1058
B1059
B1060
CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning Malfunction in air bag diagnosis sensor unit
B1061
B1062
B1063
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-62, "DTC Logic".
SRC
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946155
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and open
B1065 ASSIST A/B MODULE
Passenger air bag module circuit is open • Malfunction in passenger air bag module
B1070 [OPEN]
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-64, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946158
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-66, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946161
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and short
B1067 ASSIST A/B MODULE Passenger air bag module circuit is
• Malfunction in passenger air bag module
B1072 [GND-SHORT] shorted to ground
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-68, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946164
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and short
B1068 ASSIST A/B MODULE Passenger air bag module circuits are
• Malfunction in passenger air bag module
B1073 [SHORT] shorted to each other
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-70, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
• It detects a shock that is more than the specified level and monitors whether the driver and passenger air
bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally.
• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
DTC Logic INFOID:0000000009946167
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
B1074
B1075
B1076
CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning Malfunction in air bag diagnosis sensor unit
B1077
B1078
B1079
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-72, "DTC Logic".
SRC
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946170
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and short
DRIVER AIRBAG Driver air bag module circuit are shorted to each
B1080 • Malfunction in driver air bag module
MODULE other
B1096 • Malfunction in spiral cable
[SHORT] (including the spiral cable)
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.CHECK SPIRAL CABLE CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver air bag module connector and combination switch (spiral cable) connector.
3. Check continuity between driver air bag module harness connector and combination switch (spiral cable)
harness connector.
In the case of a frontal collision that is more than the specified impact level, the air bag diagnosis sensor unit
detects the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on pas-
sengers chest with load limiter.
DTC Logic INFOID:0000000009946173
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and open
PRE-TEN FRONT RH
B1081 Seat belt pre-tensioner RH circuit is open • Malfunction in seat belt pre-tensioner RH
[OPEN]
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE SEAT BELT PRE-TENSIONER
1. Replace seat belt pre-tensioner RH. Refer to SB-6, "SEAT BELT RETRACTOR : Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-76, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
In the case of a frontal collision that is more than the specified impact level, the air bag diagnosis sensor unit
detects the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on pas-
sengers chest with load limiter.
DTC Logic INFOID:0000000009946176
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and short
PRE-TEN FRONT RH Seat belt pre-tensioner RH circuit is
B1082 • Malfunction in seat belt pre-tensioner RH
[VB-SHORT] shorted to power supply circuit
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE SEAT BELT PRE-TENSIONER
1. Replace seat belt pre-tensioner RH. Refer to SB-6, "SEAT BELT RETRACTOR : Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-78, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
In the case of a frontal collision that is more than the specified impact level, the air bag diagnosis sensor unit
detects the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on pas-
sengers chest with load limiter.
DTC Logic INFOID:0000000009946179
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and short
PRE-TEN FRONT RH Seat belt pre-tensioner RH circuit is
B1083 • Malfunction in seat belt pre-tensioner RH
[GND-SHORT] shorted to ground
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE SEAT BELT PRE-TENSIONER
1. Replace seat belt pre-tensioner RH. Refer to SB-6, "SEAT BELT RETRACTOR : Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-80, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
In the case of a frontal collision that is more than the specified impact level, the air bag diagnosis sensor unit
detects the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on pas-
sengers chest with load limiter.
DTC Logic INFOID:0000000009946182
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and short
PRE-TEN FRONT RH Seat belt pre-tensioner RH circuits are
B1084 • Malfunction in seat belt pre-tensioner RH
[SHORT] shorted to each other
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE SEAT BELT PRE-TENSIONER
1. Replace seat belt pre-tensioner RH. Refer to SB-6, "SEAT BELT RETRACTOR : Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-82, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
In the case of a frontal collision that is more than the specified impact level, the air bag diagnosis sensor unit
detects the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on pas-
sengers chest with load limiter.
DTC Logic INFOID:0000000009946185
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and open
PRE-TEN FRONT LH
B1086 Seat belt pre-tensioner LH circuit is open • Malfunction in seat belt pre-tensioner LH
[OPEN]
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE SEAT BELT PRE-TENSIONER
1. Replace seat belt pre-tensioner LH. Refer to SB-6, "SEAT BELT RETRACTOR : Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-84, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
In the case of a frontal collision that is more than the specified impact level, the air bag diagnosis sensor unit
detects the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on pas-
sengers chest with load limiter.
DTC Logic INFOID:0000000009946188
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and short
PRE-TEN FRONT LH Seat belt pre-tensioner LH circuit is
B1087 • Malfunction in seat belt pre-tensioner LH
[VB-SHORT] shorted to power supply circuit
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE SEAT BELT PRE-TENSIONER
1. Replace seat belt pre-tensioner LH. Refer to SB-6, "SEAT BELT RETRACTOR : Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-86, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
In the case of a frontal collision that is more than the specified impact level, the air bag diagnosis sensor unit
detects the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on pas-
sengers chest with load limiter.
DTC Logic INFOID:0000000009946191
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and short
PRE-TEN FRONT LH Seat belt pre-tensioner LH circuit is
B1088 • Malfunction in seat belt pre-tensioner LH
[GND-SHORT] shorted to ground
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE SEAT BELT PRE-TENSIONER
1. Replace seat belt pre-tensioner LH. Refer to SB-6, "SEAT BELT RETRACTOR : Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-88, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
In the case of a frontal collision that is more than the specified impact level, the air bag diagnosis sensor unit
detects the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on pas-
sengers chest with load limiter.
DTC Logic INFOID:0000000009946194
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and short
PRE-TEN FRONT LH Seat belt pre-tensioner LH circuits are
B1089 • Malfunction in seat belt pre-tensioner LH
[SHORT] shorted to each other
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE SEAT BELT PRE-TENSIONER
1. Replace seat belt pre-tensioner LH. Refer to SB-6, "SEAT BELT RETRACTOR : Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-90, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
• It detects a shock that is more than the specified level and monitors whether the driver and passenger air
bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally.
• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
DTC Logic INFOID:0000000009946197
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
B1090
B1091
B1092
CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning Malfunction in air bag diagnosis sensor unit
B1093
B0194
B1095
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-92, "DTC Logic".
SRC
• It detects a shock that is more than the specified level and monitors whether the driver and passenger air
bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally.
• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
DTC Logic INFOID:0000000009946200
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
B1106
B1107
B1108
CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning Malfunction in air bag diagnosis sensor unit
B1109
B1110
B1111
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-94, "DTC Logic".
SRC
When air bag diagnosis sensor unit defines both signal voltage of the “G” sensor and the safing algorithm to
be that of collision which is more than the specified level, the driving circuit switches on and feeds the electric
ignitor of both the front side air bag and side curtain air bag.
DTC Logic INFOID:0000000009946203
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness
B1113 SATELLITE SENS RH
Satellite sensor RH is malfunctioning • Malfunction in satellite sensor RH
B1114 [UNIT FAIL]
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE SATELLITE SENSOR
1. Replace satellite sensor RH. Refer to SR-24, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-96, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
When air bag diagnosis sensor unit defines both signal voltage of the “G” sensor and the safing algorithm to
be that of collision which is more than the specified level, the driving circuit switches on and feeds the electric
ignitor of both the front side air bag and side curtain air bag.
DTC Logic INFOID:0000000009946206
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness
SATELLITE SENS RH
B1115 Satellite sensor RH is malfunctioning • Malfunction in satellite sensor RH
[COMM FAIL]
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE SATELLITE SENSOR
1. Replace satellite sensor RH. Refer to SR-24, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-98, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
When air bag diagnosis sensor unit defines both signal voltage of the “G” sensor and the safing algorithm to
be that of collision which is more than the specified level, the driving circuit switches on and feeds the electric
ignitor of both the front side air bag and side curtain air bag.
DTC Logic INFOID:0000000009946209
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
SATELLITE SENS RH Satellite sensor RH is out of the specified Diagnosis sensor unit or crash zone sensor is dif-
B1116
[UNMATCH] specification ferent from the part specified
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE SATELLITE SENSOR
1. Replace satellite sensor RH. Refer to SR-24, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-100, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
Revision: 2013 October SRC-100 2014 CUBE
B1116 SATELLITE SENSOR RH
< DTC/CIRCUIT DIAGNOSIS >
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-100, "DTC Logic". A
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END B
SRC
When air bag diagnosis sensor unit defines both signal voltage of the “G” sensor and the safing algorithm to
be that of collision which is more than the specified level, the driving circuit switches on and feeds the electric
ignitor of both the front side air bag and side curtain air bag.
DTC Logic INFOID:0000000009946212
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness
B1118 SATELLITE SENS LH
Satellite sensor LH is malfunctioning • Malfunction in satellite sensor LH
B1119 [UNIT FAIL]
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE SATELLITE SENSOR
1. Replace satellite sensor LH. Refer to SR-24, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-102, "DTC Logic"
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
When air bag diagnosis sensor unit defines both signal voltage of the “G” sensor and the safing algorithm to
be that of collision which is more than the specified level, the driving circuit switches on and feeds the electric
ignitor of both the front side air bag and side curtain air bag.
DTC Logic INFOID:0000000009946215
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness
SATELLITE SENS LH
B1120 Satellite sensor LH is malfunctioning • Malfunction in satellite sensor LH
[COMM FAIL]
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE SATELLITE SENSOR
1. Replace satellite sensor LH. Refer to SR-24, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-104, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
When air bag diagnosis sensor unit defines both signal voltage of the “G” sensor and the safing algorithm to
be that of collision which is more than the specified level, the driving circuit switches on and feeds the electric
ignitor of both the front side air bag and side curtain air bag.
DTC Logic INFOID:0000000009946218
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
SATELLITE SENS LH Satellite sensor LH is out of the specified Diagnosis sensor unit or crash zone sensor is dif-
B1121
[UNMATCH] specification ferent from the part specified
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE SATELLITE SENSOR
1. Replace satellite sensor LH. Refer to SR-24, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-106, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
Revision: 2013 October SRC-106 2014 CUBE
B1121 SATELLITE SENSOR LH
< DTC/CIRCUIT DIAGNOSIS >
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-106, "DTC Logic". A
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END B
SRC
• It detects a shock that is more than the specified level and monitors whether the driver and passenger air
bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally.
• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
DTC Logic INFOID:0000000009946221
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
B1122
B1123
B1124
CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning Malfunction in air bag diagnosis sensor unit
B1125
B1126
B1127
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-108, "DTC Logic".
SRC
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946224
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and open
SIDE MODULE RH
B1129 Side air bag module RH circuit is open • Malfunction in side air bag module RH
[OPEN]
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-110, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946227
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and short
SIDE MODULE RH Side air bag module RH circuit is shorted
B1130 • Malfunction in side air bag module RH
[VB-SHORT] to power supply circuit
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-112, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946230
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and short
SIDE MODULE RH Side air bag module RH circuit is shorted
B1131 • Malfunction in side air bag module RH
[GND-SHORT] to ground
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-114, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946233
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and short
SIDE MODULE RH Side air bag module RH circuits are short-
B1132 • Malfunction in side air bag module RH
[SHORT] ed to each other
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-116, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946236
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-118, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946239
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and short
SIDE MODULE LH Side air bag module LH circuit is shorted to
B1135 • Malfunction in side air bag module LH
[VB-SHORT] power supply circuit
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-120, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946242
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and short
SIDE MODULE LH Side air bag module LH circuit is shorted to
B1136 • Malfunction in side air bag module LH
[GND-SHORT] ground
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-122, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946245
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
• Disconnection of wiring harness and short
SIDE MODULE LH Side air bag module LH circuits are shorted
B1137 • Malfunction in side air bag module LH
[SHORT] to each other
• Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-124, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
SRC
• It detects a shock that is more than the specified level and monitors whether the driver and passenger air
bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally.
• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
DTC Logic INFOID:0000000009946248
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
B1138
B1139
B1140
CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning Malfunction in air bag diagnosis sensor unit
B1141
B1142
B1143
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-126, "DTC Logic".
SRC
• It detects a shock that is more than the specified level and monitors whether the driver and passenger air
bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally.
• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
DTC Logic INFOID:0000000009946251
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-128, "DTC Logic".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited B
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946254 C
K
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device. L
1.CHECK HARNESS CONNECTOR
Check the harness connector. M
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector. N
2.CHECK WIRING HARNESS
Check the wiring harness externals.
O
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
P
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-129, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited B
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946257 C
K
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device. L
1.CHECK HARNESS CONNECTOR
Check the harness connector. M
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector. N
2.CHECK WIRING HARNESS
Check the wiring harness externals.
O
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
P
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-131, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited B
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946260 C
WARNING: K
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device. L
1.CHECK HARNESS CONNECTOR
Check the harness connector.
M
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
N
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal? O
YES >> GO TO 3.
NO >> Replace wiring harness.
P
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-133, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited B
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946263 C
WARNING: K
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device. L
1.CHECK HARNESS CONNECTOR
Check the harness connector.
M
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
N
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal? O
YES >> GO TO 3.
NO >> Replace wiring harness.
P
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-135, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited B
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946266 C
K
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device. L
1.CHECK HARNESS CONNECTOR
Check the harness connector. M
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector. N
2.CHECK WIRING HARNESS
Check the wiring harness externals.
O
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
P
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-137, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited B
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946269 C
WARNING: K
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device. L
1.CHECK HARNESS CONNECTOR
Check the harness connector.
M
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
N
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal? O
YES >> GO TO 3.
NO >> Replace wiring harness.
P
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-139, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited B
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946272 C
K
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device. L
1.CHECK HARNESS CONNECTOR
Check the harness connector. M
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector. N
2.CHECK WIRING HARNESS
Check the wiring harness externals.
O
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
P
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-141, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited B
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.
DTC Logic INFOID:0000000009946275 C
K
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device. L
1.CHECK HARNESS CONNECTOR
Check the harness connector. M
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector. N
2.CHECK WIRING HARNESS
Check the wiring harness externals.
O
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
P
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-143, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
• It detects a shock that is more than the specified level and monitors whether the driver and passenger air B
bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally.
• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
C
DTC Logic INFOID:0000000009946278
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
E
B1154
B1155
B1156
CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning Malfunction in air bag diagnosis sensor unit
B1157 F
B1158
B1159
L
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device. M
1.CHECK HARNESS CONNECTOR
Check the harness connector. N
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors. O
2.CHECK WIRING HARNESS
Check the wiring harness externals.
P
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-145, "DTC Logic".
• It detects a shock that is more than the specified level and monitors whether the driver and passenger air B
bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally.
• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
C
DTC Logic INFOID:0000000009946281
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
E
B1170
B1171
B1172
CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning Malfunction in air bag diagnosis sensor unit
B1173 F
B1174
B1175
L
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device. M
• It detects a shock that is more than the specified level and monitors whether the driver and passenger air B
bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally.
• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
C
DTC Logic INFOID:0000000009946284
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
E
B1186
B1187
B1188
CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning Malfunction in air bag diagnosis sensor unit
B1189 F
B1190
B1191
L
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device. M
1.CHECK HARNESS CONNECTOR
Check the harness connector. N
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors. O
2.CHECK WIRING HARNESS
Check the wiring harness externals.
P
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-149, "DTC Logic".
• It detects a shock that is more than the specified level and monitors whether the driver and passenger air B
bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally.
• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
C
DTC Logic INFOID:0000000009946287
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
E
B1202
B1203
B1204
CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning Malfunction in air bag diagnosis sensor unit
B1205 F
B1206
B1207
L
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device. M
The air bags and seat belt pre-tensioners for driver and passenger are activated by the air bag diagnosis sen- B
sor unit signal transmitted at the time of the frontal collision.
DTC Logic INFOID:0000000009946290
C
DTC DETECTION LOGIC
DTC
Display contents of CON-
DTC detecting condition Possible cause
D
SULT
FRONTAL COLLISION Seat belt pre-tensioner, driver side air bag and pas-
B1209 —
DETECTION senger air bag are deployed E
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT F
With CONSULT
1. Turn ignition switch ON.
2. Perform “AIR BAG” Self Diagnostic Result. G
Without CONSULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to SRC-18, "Diagnosis with Air Bag Warning Lamp". SRC
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
I
YES >> Refer to SRC-153, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis Procedure INFOID:0000000009946291 J
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 K
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.PERFORM COLLISION DIAGNOSIS L
Perform collision diagnosis.Refer to SR-5, "FOR FRONTAL COLLISION : When SRS is activated in a colli-
sion" or SR-6, "FOR FRONTAL COLLISION : When SRS is not activated in a collision".
Is collision diagnosis complete? M
YES >> GO TO 2.
NO >> INSPECTION END
2.FINAL INSPECTION N
The side air bag and curtain air bag are activated by the air bag diagnosis sensor unit signal transmitted at the
time of side collision.
DTC Logic INFOID:0000000009946293
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.PERFORM COLLISION DIAGNOSIS
Perform collision diagnosis.Refer to SR-7, "FOR SIDE AND ROLLOVER COLLISION : When SRS is activated
in a collision" or SR-8, "FOR SIDE AND ROLLOVER COLLISION : When SRS is not activated in a collision".
Is collision diagnosis complete?
YES >> GO TO 2.
NO >> INSPECTION END
2.FINAL INSPECTION
Perform “AIR BAG” Self Diagnostic Result.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Perform diagnosis of applicable DTC.Refer to SRC-163, "DTC Index".
The seat belt pre-tensioner and curtain air bag are activated by the air bag diagnosis sensor unit signal at the B
time of rollover.
DTC Logic INFOID:0000000009946296
C
DTC DETECTION LOGIC
DTC
Display contents of
DTC detecting condition Possible cause
D
CONSULT
ROLLOVER DETEC- Seat belt pre-tensioner and curtain air bag module
B1211 —
TION are deployed because of rollover detection E
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT F
With CONSULT
1. Turn ignition switch ON.
2. Perform “AIR BAG” Self Diagnostic Result. G
Without CONSULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to SRC-18, "Diagnosis with Air Bag Warning Lamp". SRC
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
I
YES >> Refer to SRC-155, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis Procedure INFOID:0000000009946297 J
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 K
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.PERFORM COLLISION DIAGNOSIS L
Perform collision diagnosis.Refer to SR-7, "FOR SIDE AND ROLLOVER COLLISION : When SRS is activated
in a collision" or SR-8, "FOR SIDE AND ROLLOVER COLLISION : When SRS is not activated in a collision".
Is collision diagnosis complete? M
YES >> GO TO 2.
NO >> INSPECTION END
2.FINAL INSPECTION N
Satellite sensor is a G sensor that outputs voltage signal during deceleration at the time of a vehicle side colli-
sion that is more than the specified limit is detected.
DTC Logic INFOID:0000000009946299
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
B1212 • Disconnection of wiring harness
B1213 RH1 SAT-SENS Satellite sensor RH is malfunctioning • Malfunction in satellite sensor RH
B1214 • Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE SATELLITE SENSOR
1. Replace satellite sensor RH. Refer to SR-24, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-156, "DTC Logic".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
Revision: 2013 October SRC-156 2014 CUBE
B1212, B1213, B1214 SATELLITE SENSOR RH
< DTC/CIRCUIT DIAGNOSIS >
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-156, "DTC Logic". A
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END B
SRC
Satellite sensor is a G sensor that outputs voltage signal during deceleration at the time of a vehicle side colli-
sion that is more than the specified limit is detected.
DTC Logic INFOID:0000000009946302
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
B1215 • Disconnection of wiring harness
B1216 LH1 SAT-SENS Satellite sensor LH is malfunctioning • Malfunction in satellite sensor LH
B1217 • Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE SATELLITE SENSOR
1. Replace satellite sensor LH. Refer to SR-24, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-158, "DTC Logic"
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
Revision: 2013 October SRC-158 2014 CUBE
B1215, B1216, B1217 SATELLITE SENSOR LH
< DTC/CIRCUIT DIAGNOSIS >
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-158, "DTC Logic". A
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END B
SRC
• It detects a shock that is more than the specified level and monitors whether the driver and passenger air
bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally.
• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
DTC Logic INFOID:0000000009946305
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
B1218
B1219
B1220
CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning Malfunction in air bag diagnosis sensor unit
B1221
B1222
B1223
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-160, "DTC Logic".
SRC
• It detects a shock that is more than the specified level and monitors whether the driver and passenger air
bags, side air bag, curtain air bag, and pre-tensioner seat belts operate normally.
• It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
DTC Logic INFOID:0000000009946308
Display contents of
DTC DTC detecting condition Possible cause
CONSULT
B1239 CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning Malfunction in air bag diagnosis sensor unit
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-26, "Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-162, "DTC Logic".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
B1148
CURTAIN MODULE RH
Curtain air bag module RH circuits are shorted to each other
SRC-135, "DTC I
[SHORT] Logic".
CURTAIN MODULE LH SRC-137, "DTC
B1150 Curtain air bag module LH circuit is open
[OPEN] Logic". J
CURTAIN MODULE LH Curtain air bag module LH circuit is shorted to power supply SRC-139, "DTC
B1151
[VB-SHORT] circuits Logic".
CURTAIN MODULE LH SRC-141, "DTC K
B1152 Curtain air bag module LH circuit is shorted to ground
[GND-SHORT] Logic".
CURTAIN MODULE LH SRC-143, "DTC
B1153 Curtain air bag module LH circuits are shorted to each other
[SHORT] Logic".
L
SRC-145, "DTC
B1154-B1159 CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning
Logic".
SRC-147, "DTC M
B1170-B1175 CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning
Logic".
SRC-149, "DTC
B1186-B1191 CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning
Logic".
N
SRC-151, "DTC
B1202-B1207 CONTROL UNIT Air bag diagnosis sensor unit is malfunctioning
Logic".
FRONTAL COLLISION DE- Seat belt pre-tensioner, driver side air bag and passenger air SRC-153, "DTC
B1209 O
TECTION bag are deployed Logic".
SIDE COLLISION DETEC- SRC-154, "DTC
B1210 Side air bag and curtain air bag are deployed
TION Logic".
P
Seat belt pre-tensioner side curtain air bag module are de- SRC-155, "DTC
B1211 ROLLOVER DETECTION
ployed because of rollover detection Logic".
SRC-156, "DTC
B1212-B1214 RH1 SAT-SENS Satellite sensor RH is malfunctioning
Logic".
SRC-158, "DTC
B1215-B1217 LH1 SAT-SENS Satellite sensor LH is malfunctioning
Logic".
JRHWC0143GB
SRC
JRHWC0144GB
JRHWC1437GB
SRC
JRHWC1438GB
JRHWC1439GB
SRC
JRHWC1440GB
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
SEF289H
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000010166642
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Service INFOID:0000000009946315
• Never use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
• Before servicing the SRS, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
G
Replace Occupant Detection System control unit and passenger front seat cushion frame as an assembly.
Refer to SE-12, "Exploded View".
SRC