SRC PDF

RESTRAINTS
SRC
A
B
SECTION
SRS AIRBAG CONTROL SYSTEM C
E
CONTENTS
BASIC INSPECTION .................................... 3 Description ...............................................................17 F
DTC Logic ................................................................17
DIAGNOSIS AND REPAIR WORK FLOW ......... 3 Diagnosis Procedure (Component Diagnosis) ........18
Work Flow ................................................................. 3 G
B1065 B1068, B1070 B1073 PASSEN-
INTERMITTENTS INCIDENT .............................. 5 GER AIRBAG MODULE ................................... 20
Inspection Procedure ............................................... 5 Description ...............................................................20
Trouble Diagnosis with CONSULT-III ....................... 5 DTC Logic ................................................................20 SRC
Diagnosis Procedure (Component Diagnosis) ........21
FUNCTION DIAGNOSIS ............................... 6
B1134 B1137 SIDE AIRBAG MODULE LH ... 23 I
SRS AIR BAG SYSTEM ...................................... 6 Description ...............................................................23
SRS Configuration .................................................... 6 DTC Logic ................................................................23
SRS Component Parts Location ............................... 7 Diagnosis Procedure (Component Diagnosis) ........24
Driver Air Bag Module ............................................... 7 J
Front Passenger Air Bag Module .............................. 8 B1129 B1132 SIDE AIRBAG MODULE RH ... 26
Front Side Air Bag ..................................................... 8 Description ...............................................................26
Side Curtain Air Bag .................................................. 8 DTC Logic ................................................................26 K
Front Seat Belt Pre-tensioner with Load Limiter ...... 8 Diagnosis Procedure (Component Diagnosis) ........27
Direct-connect SRS Component Connectors ............ 9
B1198 B1201 SIDE CURTAIN AIR BAG
OCCUPANT CLASSIFICATION SYSTEM .........10 L
MODULE LH (FRONT) ...................................... 29
System Diagram ...................................................... 10 Description ...............................................................29
Occupant Classification System (OCS) .................. 10 DTC Logic ................................................................29
Diagnosis Procedure (Component Diagnosis) ........30 M
PASSENGER SEAT BELT WARNING SYS-
TEM ....................................................................12 B1193 B1196 SIDE CURTAIN AIR BAG
System Diagram ...................................................... 12 MODULE RH (FRONT) ..................................... 32 N
System Description ................................................. 12 Description ...............................................................32
Component Parts Location ...................................... 12 DTC Logic ................................................................32
Diagnosis Procedure (Component Diagnosis) ........33
ON BOARD DIAGNOSTIC (OBD) SYSTEM ......13 O
Trouble Diagnosis Introduction ............................... 13 B1150 B1153 SIDE CURTAIN AIR BAG
SRS Operation Check ............................................. 13 MODULE LH (REAR) ........................................ 35
Trouble Diagnosis without CONSULT-III ................ 15 Description ...............................................................35 P
CONSULT-III Function (AIR BAG) .......................... 15 DTC Logic ................................................................35
Self-Diagnosis Function (Without CONSULT-III) .... 15 Diagnosis Procedure (Component Diagnosis) ........36
COMPONENT DIAGNOSIS ......................... 17 B1145 B1148 SIDE CURTAIN AIR BAG
MODULE RH (REAR) ....................................... 38
B1049 B1052, B1054 B1057 DRIVER AIR-
Description ...............................................................38
BAG MODULE ...................................................17 DTC Logic ................................................................38
Revision: July 2009 SRC-1 2010 Pathfinder

Diagnosis Procedure (Component Diagnosis) ........ 39 B1017 B1022 OCCUPANT CLASSIFICA-
TION SYSTEM ................................................... 61
B1086 B1089 SEAT BELT PRE-TENSION- Description .............................................................. 61
ER LH ................................................................. 41 DTC Logic ............................................................... 61
Description .............................................................. 41 Diagnosis Procedure (Component Diagnosis) ........ 62
DTC Logic ............................................................... 41
Diagnosis Procedure (Component Diagnosis) ........ 42 B1209 B1211 COLLISION DETECTION ........ 64
Description .............................................................. 64
B1081 B1084 SEAT BELT PRE-TENSION- DTC Logic ............................................................... 64
ER RH ................................................................ 44 Diagnosis Procedure (Component Diagnosis) ........ 64
Description .............................................................. 44
DTC Logic ............................................................... 44 ECU DIAGNOSIS ....................................... 65
Diagnosis Procedure (Component Diagnosis) ........ 45
DIAGNOSIS SENSOR UNIT ............................. 65
B1033 B1035 CRASH ZONE SENSOR ......... 47 Wiring Diagram ....................................................... 65
Description .............................................................. 47 Trouble Diagnosis with CONSULT-III ..................... 75
DTC Logic ............................................................... 47 Trouble Diagnosis without CONSULT-III ................ 79
SYMPTOM DIAGNOSIS ............................ 83
B1118 B1120 SATELLITE SENSOR LH ........ 50
Description .............................................................. 50 SRS AIR BAG SYSTEM .................................... 83
DTC Logic ............................................................... 50 "AIR BAG" Warning Lamp Does Not Turn Off ........ 83
Diagnosis Procedure (Component Diagnosis) ........ 51 "AIR BAG" Warning Lamp Does Not Turn On ........ 83
B1113 B1115 SATELLITE SENSOR RH ....... 53 PASSENGER SEAT BELT WARNING SYS-
Description .............................................................. 53 TEM .................................................................... 85
DTC Logic ............................................................... 53 Seat Belt Warning System Does Not Function ....... 85
PRECAUTION ............................................ 86
B1XXX AIR BAG DIAGNOSIS SENSOR UNIT... 56
Description .............................................................. 56 PRECAUTIONS ................................................. 86
DTC Logic ............................................................... 56 Precaution for Supplemental Restraint System
Diagnosis Procedure (Component Diagnosis) ........ 57 (SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ................................................................. 86
B1023 PASSENGER AIR BAG OFF INDICA- Precaution for SRS "AIR BAG" and "SEAT BELT
TOR .................................................................... 58 PRE-TENSIONER" Service .................................... 86
Description .............................................................. 58 Occupant Classification System Precaution ........... 86
DTC Logic ............................................................... 58

DIAGNOSIS AND REPAIR WORK FLOW
< BASIC INSPECTION >
BASIC INSPECTION A
Work Flow INFOID:0000000005258541
B
OVERALL SEQUENCE
C
SRC
M
WHIA0348E
*1 SRC-13, "Trouble Diagnosis Intro- *2 SRC-13, "SRS Operation Check" *3 SRC-15, "CONSULT-III Function N
duction" (AIR BAG)"
*4 SRC-15, "Self-Diagnosis Function
(Without CONSULT-III)"
O
DETAILED WORK FLOW
1.CUSTOMER INFORMATION
P
Get detailed information from the customer about the symptom.
>> GO TO 2
2.PRELIMINARY CHECK
Perform preliminary check. Refer to SRC-13, "Trouble Diagnosis Introduction".

>> GO TO 3
3.TECHNICAL SERVICE BULLETINS
Check for technical service bulletins.
>> GO TO 4
4.USER MODE
Perform self-diagnosis using the "AIR BAG" warning lamp in User mode. Refer to SRC-13, "SRS Operation
Check".
>> GO TO 5
5.SELF-DIAGNOSIS
Perform SELF-DIAGNOSIS. Refer to SRC-15, "CONSULT-III Function (AIR BAG)" (w/CONSULT-III) or SRC-
15, "Self-Diagnosis Function (Without CONSULT-III)" (w/o CONSULT- III).
>> GO TO 6
6.REPLACE PART
Replace the malfunctioning part.
>> GO TO 7
7.FINAL CHECK
Check SRS using Diagnosis mode and User mode.
Does Diagnosis mode and User mode indicate SRS normal?
YES >> Inspection End.
NO >> GO TO 5

INTERMITTENTS INCIDENT
INTERMITTENTS INCIDENT
A
Inspection Procedure INFOID:0000000005258542
INTERMITTENT TROUBLE B
An intermittent incident may have occured in the past but is not being detected currently. This DTC will not be
detected on SELF DIAG [CURRENT], but may be viewed on SELF DIAG [PAST] using CONSULT-III.
Trouble Diagnosis with CONSULT-III INFOID:0000000005258543
C
DIAGNOSTIC PROCEDURE 4
D
Check SRS Repair History
1.CONSIDER POSSIBILITY THAT SELF-DIAGNOSTIC RESULT WAS NOT ERASED AFTER REPAIR
E
Check repair history of the SRS.
Have any previous repairs been made to the SRS?
YES >> Self-diagnostic result SELF-DIAG [PAST] (previously stored in the memory) might not be erased
F
after repair. Go to "DIAGNOSTIC PROCEDURE 3". Refer to SRC-15, "Self-Diagnosis Function
(Without CONSULT-III)".
NO >> Go to "DIAGNOSTIC PROCEDURE 2". Refer to SRC-13, "SRS Operation Check".
G
SRC

SRS AIR BAG SYSTEM
< FUNCTION DIAGNOSIS >
FUNCTION DIAGNOSIS
SRS AIR BAG SYSTEM
SRS Configuration INFOID:0000000005258544
AWHIA0235GB
The air bag deploys if the air bag diagnosis sensor unit is activated while the ignition switch is in the ON or
START position.
The collision modes for which supplemental restraint systems are activated are different among the SRS sys-
tems. For example, the driver air bag module, front passenger air bag module and front seat belt pre-tension-
ers are activated in a frontal collision but not in a side collision.
SRS configurations for some collision modes are as follows:
Right side colli-

SRS configuration Frontal collision Left side collision Rollover
sion
Driver air bag module x
Front passenger air bag module x
Front LH seat belt pre-tensioner x x
Front RH seat belt pre-tensioner x x
Front LH side air bag module x
Front RH side air bag module x
LH side curtain air bag module x x
RH side curtain air bag module x x

SRS AIR BAG SYSTEM
SRS Component Parts Location INFOID:0000000005258545
SRC
WHIA0196E
I
1. Side curtain air bag modules 2. Front RH side air bag module 3. Front RH seat belt pre-tensioner
4. Belt tension sensor 5. Seat belt buckle switch RH 6. RH side air bag (satellite) sensor
7. Occupant classification system sen- 8. Occupant classification system 9. Front passenger air bag off indicator J
sor control unit
10. Front passenger air bag module 11. Crash zone sensor 12. Air bag warning lamp
13. Spiral cable 14. Driver air bag module 15. LH side air bag (satellite) sensor K
16. Front LH seat belt pre-tensioner 17. Air bag diagnosis sensor unit 18. Front LH side air bag module
Driver Air Bag Module INFOID:0000000005258546

L
The driver air bag module is dual stage and located in the steering
wheel assembly. It operates with the SRS system in a frontal colli-
sion exceeding a specified level. M
O
WHIA0325E

SRS AIR BAG SYSTEM
Front Passenger Air Bag Module INFOID:0000000005258547
The front passenger air bag module is located behind the instrument
panel assembly. It operates with the SRS system in a frontal colli-
sion exceeding a specified level. Refer to SRC-10, "Occupant Clas-
sification System (OCS)" for more information.
WHIA0332E
Front Side Air Bag INFOID:0000000005258548
Front side air bag modules are built into the front seatback assem-
blies. Vehicles with side air bags are equipped with labels as shown.
WHIA0327E
Side Curtain Air Bag INFOID:0000000005258549
Side curtain air bag modules are located above the vehicle headlining.
Vehicles with side curtain air bags are equipped with labels as
shown.
WHIA0041E
Front Seat Belt Pre-tensioner with Load Limiter INFOID:0000000005258550
The seat belt pre-tensioner system with load limiter is installed for
both the driver's seat and the front passenger's seat. It operates
simultaneously with the SRS air bag system in the event of a frontal
collision with an impact exceeding a specified level.
When the frontal collision with an impact exceeding a specified level
occurs, seat belt slack resulting from clothing or other factors is
immediately taken up by the pre-tensioner. Vehicle passengers are
securely restrained.
When passengers in a vehicle are thrown forward in a collision and
the restraining force of the seat belt exceeds a specified level, the
load limiter permits the specified extension of the seat belt by the
WHIA0225E
twisting of the ELR shaft, and a relaxation of the chest-area seat belt
web tension while maintaining force.

SRS AIR BAG SYSTEM
Direct-connect SRS Component Connectors INFOID:0000000005258551
A
The following SRS components use direct-connect style harness connectors.
Driver air bag module
Front passenger air bag module B
LH side front curtain air bag module
LH side rear curtain air bag module
RH side front curtain air bag module
RH side rear curtain air bag module C
Front LH seat belt pre-tensioner
Front RH seat belt pre-tensioner
Always pull up to release locking tab prior to removing connector from SRS component. D
Always push down to lock locking tab after installing connector to
SRS component. When locked, the locking tab is level with the con-
nector housing.
E
G
WHIA0103E
SRC

OCCUPANT CLASSIFICATION SYSTEM
System Diagram INFOID:0000000005258552
ALHIA0042GB
Occupant Classification System (OCS) INFOID:0000000005258553
The occupant classification system (OCS) identifies different size occupants, out of position occupants, and
detects if child seat is present in the front passenger seat. The OCS receives inputs from the occupant classi-
fication sensor (located inside the passenger seat cushion assembly) and belt tension sensor (part of the pas-
senger front seat belt assembly and located at the belt anchor location). Depending on classification of the
passenger, the OCS sends a signal to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit
uses this signal and the seat belt buckle switch RH signal to determine deployment or non deployment of the
passenger front air bag in the event of a collision. Depending on the signals received, the air bag diagnosis
sensor unit can disable the passenger front air bag completely.
NOTE:
In case of customer concern, CONSULT-III can be used to confirm the passenger air bag status (readiness).
Passenger Air Bag Status Conditions
Front Passenger Seat PASS AIR BAG OFF Indicator Passenger Air Bag Status
CONSULT-III Display
(Condition) (Status) (Readiness)
Seat occupied OFF Active (enabled) ON
Seat occupied NOTE ON Deactivated (disabled) OFF

Seat empty OFF Deactivated (disabled) OFF
NOTE:

Passenger does not meet Occupant Classification System specifications for passenger air bag activation.
A
WHIA0195E
SRC

PASSENGER SEAT BELT WARNING SYSTEM
System Diagram INFOID:0000000005258554
ALHIA0028GB
System Description INFOID:0000000005258555
The passenger seat belt warning system will remind the driver if the
driver or front passenger seat belt should be buckled by turning on
the seat belt warning light (1). The system works in conjunction with
the occupant classification system. Refer to SRC-10, "Occupant
Classification System (OCS)".
ALHIA0043ZZ
Passenger Seat Belt Warning System Operation

Driver seat status Passenger seat status Seat belt buckle switch Seat belt buckle switch Seat belt warning lamp
(Ignition switch ON) LH status RH status
Buckled Off
Seat occupied
Buckled Unbuckled On
Seat occupied
Seat unoccupied Off

Unbuckled On
Component Parts Location INFOID:0000000005258556
Refer to SRC-7, "SRS Component Parts Location".

ON BOARD DIAGNOSTIC (OBD) SYSTEM
A
Trouble Diagnosis Introduction INFOID:0000000005258557
CAUTION: B
Do not use electrical test equipment on any circuit related to the SRS unless instructed to do so in
this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harness con-
nectors.
Do not attempt to repair, splice or modify SRS wiring harnesses. If a harness is damaged, replace it C
with a new one.
Keep ground connections clean.
DIAGNOSIS FUNCTION D
The SRS self-diagnosis results can be read by using AIR BAG warning lamp and/or CONSULT-III.
The User mode is exclusively prepared for the customer (driver). This mode warns the driver of a system mal-
function through the operation of the AIR BAG warning lamp. E
The Diagnosis mode allows the technician to locate and inspect the malfunctioning part.
The mode applications for the AIR BAG warning lamp and CONSULT-III are as follows:
F
User mode Diagnosis mode Display type
AIR BAG warning lamp X X ON-OFF operation
CONSULT-III X Monitoring G
HOW TO PERFORM TROUBLE DIAGNOSES FOR QUICK AND ACCURATE REPAIR
A good understanding of the malfunction conditions can make troubleshooting faster and more accurate.
In general, each customer feels differently about a malfunction. It is important to fully understand the symp- SRC
toms or conditions for a customer complaint.
Information From Customer
WHAT - Vehicle model I
WHEN - Date, Frequencies
WHERE - Road conditions
HOW - Operating conditions, Symptoms J
Preliminary Check
Check that the following parts are in good order.
Battery K
Fuses
System component-to-harness connections
SRS Operation Check INFOID:0000000005258558
L
M
Checking SRS Operation Using AIR BAG Warning LampUser Mode
1. Turn the ignition switch from OFF to ON, and check that the air bag warning lamp blinks.
2. Compare the SRS air bag warning lamp blinking pattern with the N
examples.
BF-1845D

SRS Air bag warning lamp examples
AIR BAG warning lamp (User mode) SRS condition Reference item
No malfunction is detected.

No further action is necessary.
SHIA0011E
Go to DIAGNOSTIC PROCEDURE
2 that follows (with CONSULT-III) or
The system is malfunctioning and
SRC-15, "Trouble Diagnosis without
needs to be repaired as indicated.
CONSULT-III" (without CONSULT-
III).
SHIA0012E
Go to COLLISION DIAGNOSIS SR-

Air bag is deployed.
19, "For Frontal Collision" or SR-20,
Seat belt pre-tensioner is deployed.
"For Side and Rollover Collision".
Air bag diagnosis sensor unit is mal-

functioning.
Air bag power supply circuit is mal- Go to SRC-83, ""AIR BAG" Warning
functioning. Lamp Does Not Turn Off".
SRS air bag warning lamp circuit is
malfunctioning.
SHIA0013E
Air bag diagnosis sensor unit is mal-

functioning. Go to SRC-83, ""AIR BAG" Warning
Air bag warning lamp circuit is mal- Lamp Does Not Turn On".
functioning.
SHIA0014E
1. Connect CONSULT-III.
2. Diagnostic code is displayed on "SELF-DIAG [CURRENT]".
If no malfunction is detected on "SELF-DIAG [CURRENT]", but malfunction is detected in "SRS Operation
Check" using the "AIR BAG" warning lamp, the following cases may exist:
"SELF-DIAG [PAST]" memory might not be erased.
The SRS system malfunctions intermittently.
Perform DIAGNOSTIC PROCEDURE 4. Refer to SRC-15, "Self-Diagnosis Function (Without CONSULT-
III)".

Trouble Diagnosis without CONSULT-III INFOID:0000000005258559
A
Inspect SRS Malfunction Using "AIR BAG" Warning LampDiagnosis Mode
B
NOTE:
SRS will not enter Diagnosis mode if no malfunction is detected in User mode.
1. Turn ignition switch ON.
C
2. After AIR BAG warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
3. Wait more than 3 seconds.
4. Repeat steps 1 to 3 two more times (3 times total). D
5. Turn ignition switch ON.
SRS is now in Diagnosis mode. Refer to SRC-79, "Trouble Diagnosis without CONSULT-III".
E
CONSULT-III Function (AIR BAG) INFOID:0000000005258560
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
F
AIR BAG diagnostic mode Description
A current Self-diagnosis result (also indicated by the number of warning lamp flashes in the Diagnosis
SELF-DIAG [CURRENT] mode) is displayed on the CONSULT-III screen in real time. This refers to a malfunctioning part requir- G
ing repairs.
Diagnosis results previously stored in the memory are displayed on the CONSULT-III screen. The
SELF-DIAG [PAST]
stored results will remain until memory erasing is executed. SRC
With TROUBLE DIAG RECORD, diagnosis results previously erased by a reset operation can be dis-
TROUBLE DIAG RECORD
played on the CONSULT-III screen.
Air bag diagnosis sensor unit ECU discriminated number (identification number) is displayed. Air bag I
ECU DISCRIMINATED NO. diagnosis sensor unit has individual ECU discriminated number (identification number) based on model
and equipment.
The STATUS (readiness) of the front passenger air bag module is displayed. The STATUS displayed
(ON/OFF) depends on the signals supplied to the occupant classification system control module and
J
PASSENGER AIR BAG
air bag diagnosis sensor unit. Refer to SRC-10, "Occupant Classification System (OCS)" for more in-
formation.
K
Self-Diagnosis Function (Without CONSULT-III) INFOID:0000000005258561
The reading of these results is accomplished using one of two modes User mode and Diagnosis mode.
After a malfunction is repaired, turn the ignition switch OFF for at least one second, then back ON. Diagnosis L
mode returns to the User mode. At that time, the self-diagnostic result is cleared.

HOW TO CHANGE SELF-DIAGNOSIS MODE
SHIA0183E
Final Check of SRS Using CONSULT-IIIDiagnosis Mode
1. Connect CONSULT-III.
2. If no DTC is detected on SELF-DIAG [CURRENT], repair of SRS is completed. Go to step 3.
If any DTC is detected on SELF-DIAG [CURRENT], the malfunctioning part has not been repaired com-
pletely or another malfunctioning part is being detected. Perform DIAGNOSTIC PROCEDURE 2. Refer to
SRC-13, "SRS Operation Check".
3. Touch ERASE.
NOTE:
Touch ERASE to clear the memory of the malfunction (SELF-DIAG [PAST]).
If the memory of the malfunction in SELF-DIAG [PAST] is not erased, the User mode shows the system
malfunction by the operation of the warning lamp even if the malfunction is repaired completely.
4. Touch BACK key of CONSULT-III. Touch SELF-DIAG [PAST].
5. Check that no malfunction is detected on SELF-DIAG [PAST].
6. Touch BACK key of CONSULT-III to return to User mode from Diagnosis mode.
7. Turn ignition switch OFF and then turn off and disconnect CONSULT-III.
8. Go to SRC-13, "SRS Operation Check".
Check SRS Repair History
1.CONSIDER POSSIBILITY THAT SELF-DIAGNOSTIC RESULT WAS NOT ERASED AFTER REPAIR
Check repair history of the SRS.
Have any previous repairs been made to the SRS?
YES >> Self-diagnostic result SELF-DIAG [PAST] (previously stored in the memory) might not be erased
after repair. Perform DIAGNOSTIC PROCEDURE 3. Refer to SRC-15, "Self-Diagnosis Function
(Without CONSULT-III)".
NO >> Perform DIAGNOSTIC PROCEDURE 2. Refer to SRC-13, "SRS Operation Check".

B1049 B1052, B1054 B1057 DRIVER AIRBAG MODULE
< COMPONENT DIAGNOSIS >
COMPONENT DIAGNOSIS A
Description INFOID:0000000005258562
B
DTC B1049 B1052, B1054 B1057 DRIVER AIRBAG MODULE

The driver air bag module is dual stage and wired to the air bag diagnosis sensor unit through the spiral cable. C
The air bag diagnosis sensor unit will monitor for opens and shorts in detected lines to the driver air bag mod-
ule including the spiral cable.
D
PART LOCATION
DTC Logic INFOID:0000000005258563 E
DTC DETECTION LOGIC

With CONSULT-lll F
CONSULT-III name DTC DTC detecting condition Repair order

G
Driver air bag module circuit (DR1) is open 1. Visually check the wiring harness connection.
B1049
DRIVER AIRBAG MODULE (including the spiral cable). 2. Replace the harness if it has visible damage.
[OPEN] 3. Replace the driver air bag module.
Driver air bag module circuit (DR2) is open
B1054 4. Replace the spiral cable. SRC
(including the spiral cable).
5. Replace the air bag diagnosis sensor unit.
Driver air bag module circuit (DR1) is 6. Replace the related harness.
B1050 shorted to a power supply circuit
DRIVER AIRBAG MODULE (including the spiral cable). I
[VB-SHORT] Driver air bag module circuit (DR2) is
(including the spiral cable). J
Driver air bag module circuit (DR1) is
B1051 shorted to ground
DRIVER AIRBAG MODULE (including the spiral cable).
K
[GND-SHORT] Driver air bag module circuit (DR2) is
L
Driver air bag module circuits (DR1) are
B1052 shorted to each other
[SHORT] Driver air bag module circuits (DR2) are M
N
Without CONSULT-lll
WHIA0260E
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

1.INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check for the DTC on CONSULT-lll.
Is the DTC detected?
YES >> Refer to SRC-18, "Diagnosis Procedure (Component Diagnosis)".
NO >> Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.IGNITION SWITCH
>> GO TO 2
2.IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3
3.WAIT TIME
Wait more than 3 seconds.
>> GO TO 4
4.REPEAT STEPS
Repeat steps 1 to 3 twice.
>> GO TO 5.
5.IGNITION SWITCH
>> GO TO 6.
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-15, "Trouble Diag-
nosis without CONSULT-III".
>> END
Diagnosis Procedure (Component Diagnosis) INFOID:0000000005258564
Recheck SRS after each replacement.

1.HARNESS CONNECTOR
Is there any visible damage to the connector?
YES or NO
YES >> Replace the harness.
NO >> GO TO 2

2.WIRING HARNESS A
Is there any visible damage to the harness?
YES or NO
YES >> Replace the harness. B
NO >> GO TO 3
3.DRIVER AIR BAG MODULE
C
Replace the driver air bag module. Refer to SR-5, "Removal and Installation".
>> GO TO 4 D
4.SPIRAL CABLE
Replace the spiral cable. Refer to SR-7, "Removal and Installation".
E
>> GO TO 5
5.AIR BAG DIAGNOSIS SENSOR UNIT F
Replace the air bag diagnosis sensor unit. Refer to SR-16, "Removal and Installation".
>> GO TO 6 G
6.RELATED HARNESS
Replace the related harness. SRC
>> END
I

B1065 B1068, B1070 B1073 PASSENGER AIRBAG MODULE
DTC B1065 B1068, B1070 B1073 PASSENGER AIR BAG MODULE

The passenger air bag module is dual stage and wired to the air bag diagnosis sensor unit. The air bag diag-
nosis sensor unit will monitor for opens and shorts in detected lines to the passenger air bag module.
PART LOCATION
DTC Logic INFOID:0000000005258566
DTC DETECTION LOGIC

With CONSULT-lll

Front passenger air bag module circuit 1. Visually check the wiring harness connection.
B1065
ASSIST A/B MODULE (AS1) is open. 2. Replace the harness if it has visible damage.
[OPEN] 3. Replace the front passenger air bag module.
Front passenger air bag module circuit
B1070 4. Replace the air bag diagnosis sensor unit.
(AS2) is open.
5. Replace the related harness.
B1066
ASSIST A/B MODULE (AS1) is shorted to a power supply circuit.
[VB-SHORT] Front passenger air bag module circuit
B1071
(AS2) is shorted to a power supply circuit.
B1067
ASSIST A/B MODULE (AS1) is shorted to ground.
[GND-SHORT] Front passenger air bag module circuit
B1072
(AS2) is shorted to ground.
Front passenger air bag module circuits
B1068
ASSIST A/B MODULE (AS1) are shorted to each other.
[SHORT] Front passenger air bag module circuits
B1073
(AS2) are shorted to each other.
Without CONSULT-lll
WHIA0261E

1.INSPECTION START
>> GO TO 2.
YES >> Refer to SRC-21, "Diagnosis Procedure (Component Diagnosis)". A
NOTE: B
1.IGNITION SWITCH C
>> GO TO 2 D
2.IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second. E
>> GO TO 3
3.WAIT TIME F
G
>> GO TO 4
4.REPEAT STEPS
Repeat steps 1 to 3 twice. SRC
>> GO TO 5
I
5.IGNITION SWITCH
J
>> GO TO 6
6.DIAGNOSTIC MODE K
L
>> END
M
1.HARNESS CONNECTOR
N
YES or NO
YES >> Replace the harness. O
NO >> GO TO 2
2.WIRING HARNESS
Is there any visible damage to the harness? P
YES or NO
NO >> GO TO 3
3.FRONT PASSENGER AIR BAG MODULE
Replace the front passenger air bag module. Refer to SR-9, "Removal and Installation".

>> GO TO 4
4.AIR BAG DIAGNOSIS SENSOR UNIT
>> GO TO 5
5.RELATED HARNESS
Replace the related harness.
>> END

B1134 B1137 SIDE AIRBAG MODULE LH
A
DTC B1134 B1137 FRONT LH SIDE AIR BAG MODULE B

The front LH side air bag module is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor
unit will monitor for opens and shorts in detected lines to the front LH side air bag module.
C
PART LOCATION
D
DTC DETECTION LOGIC

E
With CONSULT-lll

F
SIDE MODULE LH Front LH side air bag module circuit is 1. Visually check the wiring harness connection.
B1134
[OPEN] open. 2. Replace the harness if it has visible damage.
3. Replace the front LH seat back assembly.
SIDE MODULE LH Front LH side air bag module circuit is G
[VB-SHORT] shorted to a power supply circuit.
SIDE MODULE LH Front LH side air bag module circuit is
B1136
[GND-SHORT] shorted to ground.
SRC
SIDE MODULE LH Front LH side air bag module circuits are
B1137
[SHORT] shorted to each other.
I
Without CONSULT-lll
WHIA0265E
DTC CONFIRMATION PROCEDURE (With CONSULT-lll) M
1.INSPECTION START
Turn ignition switch ON. N
>> GO TO 2.
2.CHECK SELF-DIAG RESULT O

Is the DTC detected? P
NOTE:
1.IGNITION SWITCH
>> GO TO 2
2.IGNITION SWITCH
>> GO TO 3
3.WAIT TIME
>> GO TO 4
4.REPEAT STEPS
>> GO TO 5
5.IGNITION SWITCH
>> GO TO 6
6.DIAGNOSTIC MODE
>> END

1.HARNESS CONNECTOR
YES or NO
NO >> GO TO 2
2.WIRING HARNESS
YES or NO
NO >> GO TO 3
3.FRONT LH SIDE AIR BAG MODULE
Replace the front LH seat back assembly. Refer to SE-30, "Removal and Installation".
>> GO TO 4
>> GO TO 5
5.RELATED HARNESS
A
>> END
SRC

B1129 B1132 SIDE AIRBAG MODULE RH
DTC B1129 B1132 FRONT RH SIDE AIR BAG MODULE

The front RH side air bag module is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor
unit will monitor for opens and shorts in detected lines to the front RH side air bag module.
PART LOCATION
DTC DETECTION LOGIC

With CONSULT-lll

SIDE MODULE RH Front RH side air bag module circuit is 1. Visually check the wiring harness connection.
B1129
3. Replace the front RH seat back assembly.
SIDE MODULE RH Front RH side air bag module circuit is
B1131
SIDE MODULE RH Front RH side air bag module circuits are
B1132
Without CONSULT-lll
WHIA0264E

1.INSPECTION START
>> GO TO 2.
NOTE:
1.IGNITION SWITCH
A
>> GO TO 2
2.IGNITION SWITCH B
>> GO TO 3 C
3.WAIT TIME
Wait more than 3 seconds. D
>> GO TO 4
4.REPEAT STEPS E
F
>> GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON. G
>> GO TO 6
SRC
6.DIAGNOSTIC MODE
nosis without CONSULT-III". I
>> END
J

1.HARNESS CONNECTOR K

YES or NO L
NO >> GO TO 2
2.WIRING HARNESS M
YES or NO
N
NO >> GO TO 3
3.FRONT RH SIDE AIR BAG MODULE O
Replace the front RH seat back assembly. Refer to SE-30, "Removal and Installation".
>> GO TO 4 P

>> GO TO 5
5.RELATED HARNESS
>> END

B1198 B1201 SIDE CURTAIN AIR BAG MODULE LH (FRONT)
A
DTC B1198 B1201 LH SIDE CURTAIN AIR BAG MODULE (FRONT) B

The LH side curtain air bag module (front) is wired to the air bag diagnosis sensor unit. The air bag diagnosis
sensor unit will monitor for opens and shorts in detected lines to the LH side curtain air bag module (front).
C
PART LOCATION
D
DTC DETECTION LOGIC

E
With CONSULT-lll

F
FR CURTN MODULE LH LH side curtain air bag module (front) cir- 1. Visually check the wiring harness connection.
B1198
[OPEN] cuit is open. 2. Replace the harness if it has visible damage.
3. Replace the LH side curtain air bag module.
FR CURTN MODULE LH LH side curtain air bag module (front) cir- G
[VB-SHORT] cuit is shorted to a power supply circuit.
FR CURTN MODULE LH LH side curtain air bag module (front) cir-
B1200
[GND-SHORT] cuit is shorted to ground.
SRC
FR CURTN MODULE LH LH side curtain air bag module (front) cir-
B1201
[SHORT] cuits are shorted to each other.
I
Without CONSULT-lll
WHIA0255E
1.INSPECTION START
>> GO TO 2.

NOTE:
1.IGNITION SWITCH
>> GO TO 2
2.IGNITION SWITCH
>> GO TO 3
3.WAIT TIME
>> GO TO 4
4.REPEAT STEPS
>> GO TO 5
5.IGNITION SWITCH
>> GO TO 6
6.DIAGNOSTIC MODE
>> END

1.HARNESS CONNECTOR
YES or NO
NO >> GO TO 2
2.WIRING HARNESS
YES or NO
NO >> GO TO 3
3.LH SIDE CURTAIN AIR BAG MODULE
Replace the LH side curtain air bag module. Refer to SR-12, "Removal and Installation".
>> GO TO 4
>> GO TO 5
5.RELATED HARNESS
A
>> END
SRC

B1193 B1196 SIDE CURTAIN AIR BAG MODULE RH (FRONT)
DTC B1193 B1196 RH SIDE CURTAIN AIR BAG MODULE (FRONT)

The RH side curtain air bag module (front) is wired to the air bag diagnosis sensor unit. The air bag diagnosis
sensor unit will monitor for opens and shorts in detected lines to the RH side curtain air bag module (front).
PART LOCATION
DTC DETECTION LOGIC

With CONSULT-lll

FR CURTN MODULE RH RH side curtain air bag module (front) cir- 1. Visually check the wiring harness connection.
B1193
3. Replace the RH side curtain air bag module.
FR CURTN MODULE RH RH side curtain air bag module (front) cir-
B1195
B1196
Without CONSULT-lll
WHIA0253E

1.INSPECTION START
>> GO TO 2.
NOTE:
1.IGNITION SWITCH
A
>> GO TO 2
2.IGNITION SWITCH B
>> GO TO 3 C
3.WAIT TIME
>> GO TO 4
4.REPEAT STEPS E
F
>> GO TO 5
5.IGNITION SWITCH
>> GO TO 6
SRC
6.DIAGNOSTIC MODE
>> END
J


YES or NO L
NO >> GO TO 2
2.WIRING HARNESS M
YES or NO
N
NO >> GO TO 3
3.RH SIDE CURTAIN AIR BAG MODULE O
Replace the RH side curtain air bag module. Refer to SR-12, "Removal and Installation".
>> GO TO 4 P

>> GO TO 5
5.RELATED HARNESS
>> END

B1150 B1153 SIDE CURTAIN AIR BAG MODULE LH (REAR)
A
DTC B1150 B1153 LH SIDE CURTAIN AIR BAG MODULE (REAR) B

The LH side curtain air bag module (rear) is wired to the air bag diagnosis sensor unit. The air bag diagnosis
sensor unit will monitor for opens and shorts in detected lines to the LH side curtain air bag module (rear).
C
PART LOCATION
D
DTC DETECTION LOGIC

E
With CONSULT-lll

F
CURTAIN MODULE LH LH side curtain air bag module (rear) circuit 1. Visually check the wiring harness connection.
B1150
[OPEN] is open. 2. Replace the harness if it has visible damage.
CURTAIN MODULE LH LH side curtain air bag module (rear) circuit G
[VB-SHORT] is shorted to a power supply circuit.
CURTAIN MODULE LH LH side curtain air bag module (rear) circuit
B1152
[GND-SHORT] is shorted to ground.
SRC
CURTAIN MODULE LH LH side curtain air bag module (rear) cir-
B1153
I
Without CONSULT-lll
WHIA0254E
1.INSPECTION START
>> GO TO 2.

NOTE:
1.IGNITION SWITCH
>> GO TO 2
2.IGNITION SWITCH
>> GO TO 3
3.WAIT TIME
>> GO TO 4
4.REPEAT STEPS
>> GO TO 5
5.IGNITION SWITCH
>> GO TO 6
6.DIAGNOSTIC MODE
>> END

1.HARNESS CONNECTOR
YES or NO
NO >> GO TO 2
2.WIRING HARNESS
YES or NO
NO >> GO TO 3
3.LH SIDE CURTAIN AIR BAG MODULE
Replace the LH side curtain air bag module. Refer to SR-12, "Removal and Installation".
>> GO TO 4
>> GO TO 5
5.RELATED HARNESS
A
>> END
SRC

B1145 B1148 SIDE CURTAIN AIR BAG MODULE RH (REAR)
DTC B1145 B1148 RH SIDE CURTAIN AIR BAG MODULE (REAR)

The RH side curtain air bag module (rear) is wired to the air bag diagnosis sensor unit. The air bag diagnosis
sensor unit will monitor for opens and shorts in detected lines to the RH side curtain air bag module (rear).
PART LOCATION
DTC DETECTION LOGIC

With CONSULT-lll

CURTAIN MODULE RH RH side curtain air bag module (rear) cir- 1. Visually check the wiring harness connection.
B1145
CURTAIN MODULE RH RH side curtain air bag module (rear) cir-
B1147
B1148
Without CONSULT-lll
WHIA0252E

1.INSPECTION START
>> GO TO 2.
NOTE:
1.IGNITION SWITCH
A
>> GO TO 2
2.IGNITION SWITCH B
>> GO TO 3 C
3.WAIT TIME
>> GO TO 4
4.REPEAT STEPS E
F
>> GO TO 5
5.IGNITION SWITCH
>> GO TO 6
SRC
6.DIAGNOSTIC MODE
>> END
J


YES or NO L
NO >> GO TO 2
2.WIRING HARNESS M
YES or NO
N
NO >> GO TO 3
3.RH SIDE CURTAIN AIR BAG MODULE O
Replace the RH side curtain air bag module. Refer to SR-12, "Removal and Installation".
>> GO TO 4 P

>> GO TO 5
5.RELATED HARNESS
>> END

B1086 B1089 SEAT BELT PRE-TENSIONER LH
A
DTC B1086 B1089 SEAT BELT PRE-TENSIONER LH B

The seat belt pre-tensioner LH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit
will monitor for opens and shorts in detected lines to the seat belt pre-tensioner LH.
C
PART LOCATION
D
DTC DETECTION LOGIC

E
With CONSULT-lll

F
PRE-TEN FRONT LH LH seat belt pre-tensioner circuit is open. 1. Visually check the wiring harness connection.
B1086
[OPEN] 2. Replace the harness if it has visible damage.
3. Replace the front LH seat belt pre-tensioner.
PRE-TEN FRONT LH LH seat belt pre-tensioner circuit is shorted G
[VB-SHORT] to a power supply circuit.
PRE-TEN FRONT LH LH seat belt pre-tensioner circuit is shorted
B1088
[GND-SHORT] to ground.
SRC
PRE-TEN FRONT LH LH seat belt pre-tensioner circuits are
B1089
I
Without CONSULT-lll
WHIA0263E
1.INSPECTION START
>> GO TO 2.

NOTE:
1.IGNITION SWITCH
>> GO TO 2
2.IGNITION SWITCH
>> GO TO 3
3.WAIT TIME
>> GO TO 4
4.REPEAT STEPS
>> GO TO 5
5.IGNITION SWITCH
>> GO TO 6
6.DIAGNOSTIC MODE
>> END

1.HARNESS CONNECTOR
YES or NO
NO >> GO TO 2
2.WIRING HARNESS
YES or NO
NO >> GO TO 3
3.FRONT LH SEAT BELT PRE-TENSIONER
Replace the front LH seat belt pre-tensioner. Refer to SR-15, "Removal and Installation".
>> GO TO 4
>> GO TO 5
5.RELATED HARNESS
A
>> END
SRC

B1081 B1084 SEAT BELT PRE-TENSIONER RH
DTC B1081 B1084 SEAT BELT PRE-TENSIONER RH

The seat belt pre-tensioner RH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit
will monitor for opens and shorts in detected lines to the seat belt pre-tensioner RH.
PART LOCATION
DTC DETECTION LOGIC

With CONSULT-lll

PRE-TEN FRONT RH RH seat belt pre-tensioner circuit is open. 1. Visually check the wiring harness connection.
B1081
[OPEN] 2. Replace the harness if it has visible damage.
3. Replace the front RH seat belt pre-tensioner.
PRE-TEN FRONT RH RH seat belt pre-tensioner circuit is short-
[VB-SHORT] ed to a power supply circuit.
PRE-TEN FRONT RH RH seat belt pre-tensioner circuit is short-
B1083
[GND-SHORT] ed to ground.
PRE-TEN FRONT RH RH seat belt pre-tensioner circuits are
B1084
Without CONSULT-lll
WHIA0262E

1.INSPECTION START
>> GO TO 2.
NOTE:
1.IGNITION SWITCH
A
>> GO TO 2
2.IGNITION SWITCH B
>> GO TO 3 C
3.WAIT TIME
>> GO TO 4
4.REPEAT STEPS E
F
>> GO TO 5
5.IGNITION SWITCH
>> GO TO 6
SRC
6.DIAGNOSTIC MODE
>> END
J


YES or NO L
NO >> GO TO 2
2.WIRING HARNESS M
YES or NO
N
NO >> GO TO 3
3.FRONT RH SEAT BELT PRE-TENSIONER O
Replace the front RH seat belt pre-tensioner. Refer to SR-15, "Removal and Installation".
>> GO TO 4 P

>> GO TO 5
5.RELATED HARNESS
>> END

B1033 B1035 CRASH ZONE SENSOR
A
DTC B1033 B1035 CRASH ZONE SENSOR B

The crash zone sensor is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will
monitor for opens and shorts in detected lines to the crash zone sensor.
C
PART LOCATION
D
DTC DETECTION LOGIC

E
With CONSULT-lll

F
CRASH ZONE SEN B1033 Crash zone sensor has malfunctioned. 1. Visually check the wiring harness connection.
[UNIT FAIL] 2. Replace the harness if it has visible damage.
B1034
3. Replace the crash zone sensor.
CRASH ZONE SEN Crash zone sensor communication error. 4. Replace the air bag diagnosis sensor unit. G
B1035
[COMM FAIL] 5. Replace the related harness.
Without CONSULT-lll SRC
K
WHIA0200E
DTC CONFIRMATION PROCEDURE (With CONSULT-lll) L

1.INSPECTION START
M
>> GO TO 2.
2.CHECK SELF-DIAG RESULT N
O
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll) P
NOTE:
1.IGNITION SWITCH
>> GO TO 2

2.IGNITION SWITCH
>> GO TO 3
3.WAIT TIME
>> GO TO 4
4.REPEAT STEPS
>> GO TO 5
5.IGNITION SWITCH
>> GO TO 6
6.DIAGNOSTIC MODE
>> END

1.HARNESS CONNECTOR
YES or NO
NO >> GO TO 2
2.WIRING HARNESS
YES or NO
NO >> GO TO 3
3.CRASH ZONE SENSOR
Replace the crash zone sensor. Refer to SR-13, "Removal and Installation".
>> GO TO 4
>> GO TO 5
5.RELATED HARNESS

>> END
A
SRC

B1118 B1120 SATELLITE SENSOR LH
DTC B1118 B1120 SATELLITE SENSOR LH

The satellite sensor LH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will
monitor the satellite sensor LH for internal failures and it's circuits for communication errors.
PART LOCATION
DTC DETECTION LOGIC

With CONSULT-lll
SATELLITE SENS LH B1118 LH side air bag satellite sensor has mal- 1. Visually check the wiring harness connection.
[UNIT FAIL] functioned. 2. Replace the harness if it has visible damage.
B1119
3. Replace the LH side air bag satellite sensor.
SATELLITE SENS LH LH side air bag satellite sensor communi- 4. Replace the air bag diagnosis sensor unit.
B1120
[COMM FAIL] cation error. 5. Replace the related harness.
Without CONSULT-lll
WHIA0204E

1.INSPECTION START
>> GO TO 2.
NOTE:
1.IGNITION SWITCH
>> GO TO 2

2.IGNITION SWITCH A
>> GO TO 3 B
3.WAIT TIME
C
>> GO TO 4
4.REPEAT STEPS D
E
>> GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON. F
>> GO TO 6
6.DIAGNOSTIC MODE G
nosis without CONSULT-III". SRC
>> END
I

1.HARNESS CONNECTOR J

YES or NO K
NO >> GO TO 2
2.WIRING HARNESS L
YES or NO
M
NO >> GO TO 3
3.LH SIDE AIR BAG SATELLITE SENSOR N
Replace the LH side air bag satellite sensor. Refer to SR-14, "Removal and Installation".
>> GO TO 4 O
Replace the air bag diagnosis sensor unit. Refer to SR-16, "Removal and Installation". P
>> GO TO 5
5.RELATED HARNESS

>> END

B1113 B1115 SATELLITE SENSOR RH
A
DTC B1113 B1115 SATELLITE SENSOR RH B

The satellite sensor RH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will
monitor the satellite sensor RH for internal failures and it's circuits for communication errors.
C
PART LOCATION
D
DTC DETECTION LOGIC

E
With CONSULT-lll

F
SATELLITE SENS RH B1113 RH side air bag satellite sensor has mal- 1. Visually check the wiring harness connection.
B1114
3. Replace the RH side air bag satellite sensor.
SATELLITE SENS RH RH side air bag satellite sensor communi- 4. Replace the air bag diagnosis sensor unit. G
B1115
[COMM FAIL] cation error. 5. Replace the related harness.
Without CONSULT-lll SRC
K
WHIA0203E
DTC CONFIRMATION PROCEDURE (With CONSULT-lll) L

1.INSPECTION START
M
>> GO TO 2.
2.CHECK SELF-DIAG RESULT N
O
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll) P
NOTE:
1.IGNITION SWITCH
>> GO TO 2

2.IGNITION SWITCH
>> GO TO 3
3.WAIT TIME
>> GO TO 4
4.REPEAT STEPS
>> GO TO 5
5.IGNITION SWITCH
>> GO TO 6
6.DIAGNOSTIC MODE
>> END

1.HARNESS CONNECTOR
YES or NO
NO >> GO TO 2
2.WIRING HARNESS
YES or NO
NO >> GO TO 3
3.RH SIDE AIR BAG SATELLITE SENSOR
Replace the RH side air bag satellite sensor. Refer to SR-14, "Removal and Installation".
>> GO TO 4
>> GO TO 5
5.RELATED HARNESS

>> END
A
SRC

B1XXX AIR BAG DIAGNOSIS SENSOR UNIT
DTC B1XXX AIR BAG DIAGNOSIS SENSOR UNIT

The air bag diagnosis sensor unit will run self diagnostics when the ignition switch is turned ON. It has the
potential to set many diagnostic trouble codes which will conform to the B1XXX format, but will not match any
other SRS diagnostic trouble codes. Refer to SRC-15, "CONSULT-III Function (AIR BAG)".
PART LOCATION
DTC DETECTION LOGIC

With CONSULT-lll

Air bag diagnosis sensor unit is malfunc- 1. Visually check the wiring harness connection.
tioning. 2. Replace the harness if it has visible damage.
CONTROL UNIT B1XXX
Without CONSULT-lll
WHIA0198E

1.INSPECTION START
>> GO TO 2.
NOTE:
1.IGNITION SWITCH
>> GO TO 2

2.IGNITION SWITCH A
>> GO TO 3 B
3.WAIT TIME
C
>> GO TO 4
4.REPEAT STEPS D
E
>> GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON. F
>> GO TO 6
6.DIAGNOSTIC MODE G
nosis without CONSULT-III". SRC
>> END
I

1.HARNESS CONNECTOR J

YES or NO K
NO >> GO TO 2
2.WIRING HARNESS L
YES or NO
M
NO >> GO TO 3
3.AIR BAG DIAGNOSIS SENSOR UNIT N
>> GO TO 4 O
4.RELATED HARNESS
Replace the related harness. P
>> END

B1023 PASSENGER AIR BAG OFF INDICATOR
DTC B1023 FRONT PASSENGER AIR BAG OFF INDICATOR

The front passenger air bag off indicator is wired to the air bag diagnosis sensor unit. The air bag diagnosis
sensor unit monitors the front passenger air bag off indicator and circuit for failures.
PART LOCATION
DTC DETECTION LOGIC

With CONSULT-lll

Front passenger air bag off indicator is 1. Visually check the wiring harness connection.
malfunctioning. 2. Replace the harness if it has visible damage.
3. Replace the front passenger air bag off indi-
PASS A/B INDCTR CKT B1023
cator.
Without CONSULT-lll
WHIA0212E

1.INSPECTION START
>> GO TO 2.
NOTE:
1.IGNITION SWITCH

>> GO TO 2
2.IGNITION SWITCH A
B
>> GO TO 3
3.WAIT TIME
C
>> GO TO 4 D
4.REPEAT STEPS
E
>> GO TO 5
5.IGNITION SWITCH F
>> GO TO 6 G
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-15, "Trouble Diag- SRC
>> END I
Recheck SRS after each replacement. J

1.HARNESS CONNECTOR
Is there any visible damage to the connector? K
YES or NO
NO >> GO TO 2 L
2.WIRING HARNESS
M
YES or NO
NO >> GO TO 3
N
3.FRONT PASSENGER AIR BAG OFF INDICATOR
Replace the front passenger air bag off indicator. Refer to IP-12, "Removal and Installation".
O
>> GO TO 4
4.AIR BAG DIAGNOSIS SENSOR UNIT P
>> GO TO 5
5.RELATED HARNESS

>> END

B1017 B1022 OCCUPANT CLASSIFICATION SYSTEM
A
DTC B1017 B1022 OCCUPANT CLASSIFICATION SYSTEM (OCS) B

The OCS control unit is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will mon-
itor the OCS for failures and interuptions in communication between the OCS control unit and the air bag
diagnosis sensor unit. C
PART LOCATION
Refer to SRC-7, "SRS Component Parts Location". D
DTC DETECTION LOGIC E
With CONSULT-lll
F
B1017 The OCS control unit is malfunctioning. 1. Replace the RH front seat cushion assembly.
OCCUPANT SENS C/U Do not disassemble the seat cushion assem-
B1020 G
[UNIT FAIL] bly.
B1021
OCCUPANT SENS The OCS sensor is malfunctioning.
B1018
[UNIT FAIL] SRC
The belt tension sensor is malfunctioning. 1. Visually check the wiring harness connection.
2. Replace the harness if it has visible damage.
3. Replace the RH front seat belt assembly. I
BELT TENSION SENS
B1019 4. Replace the RH front seat cushion assembly.
[UNIT FAIL]
Do not disassemble the seat cushion assem-
bly.
5. Replace the related harness. J
Communication between the OCS control 1. Visually check the wiring harness connection.
unit and the air bag diagnosis sensor unit is 2. Replace the harness if it has visible damage.
interrupted. 3. Replace the RH front seat cushion assembly. K
OCCUPANT SENS C/U
B1022 Do not disassemble the seat cushion assem-
[COMM FAIL]
bly.
5. Replace the related harness. L
Without CONSULT-lll
M
WHIA0211E
P

1.INSPECTION START
>> GO TO 2.

NOTE:
1.IGNITION SWITCH
>> GO TO 2
2.IGNITION SWITCH
>> GO TO 3
3.WAIT TIME
>> GO TO 4
4.REPEAT STEPS
>> GO TO 5
5.IGNITION SWITCH
>> GO TO 6
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-7, "SRS Compo-
nent Parts Location".
>> END

1.DTC
Does CONSULT-III indicate B1019 or B1022?
YES or NO
YES >> GO TO 2
NO >> GO TO 6
2.HARNESS CONNECTOR
YES or NO
NO >> GO TO 3

3.WIRING HARNESS A
YES or NO
YES >> Replace the harness. B
NO >> GO TO 4
4.DTC
C
Does CONSULT-III indicate B1022?
YES or NO
YES >> GO TO 6 D
NO >> GO TO 5
5.REPLACE RH FRONT SEAT BELT ASSEMBLY
Replace the RH front seat belt assembly. E
>> GO TO 6
6.REPLACE RH FRONT SEAT CUSHION ASSEMBLY F
Replace the RH front seat cushion assembly. Refer to SE-30, "Removal and Installation".
G
>> GO TO 7
7.AIR BAG DIAGNOSIS SENSOR UNIT SRC
>> END. I

B1209 B1211 COLLISION DETECTION
B1209 B1211 COLLISION DETECTION
DTC B1209 - B1211 COLLISION DETECTION

The air bag diagnosis sensor unit will set this DTC if it has detected a collision or rollover which has resulted in
a deployment of one or more air bags or pre-tensioners. If this DTC is detected after a SRS repair, the air bag
diagnosis sensor unit has not yet been replaced. This DTC can not be erased.
PART LOCATION
DTC DETECTION LOGIC

With CONSULT-lll

FRONTAL COLLISION Driver and/or front passenger air bag mod- Refer to SR-19, "For Frontal Collision".
B1209
DETECTION ules are deployed.
SIDE COLLISION DE- Side and/or curtain air bag modules are Refer to SR-20, "For Side and Rollover Collision".
B1210
TECTION deployed.
ROLLOVER DETEC- Curtain air bag module and seat belt pre-
B1211
TION tensioner are deployed.

1.INSPECTION START
>> GO TO 2.
Refer to SR-19, "For Frontal Collision" or SR-20, "For Side and Rollover Collision".

DIAGNOSIS SENSOR UNIT
< ECU DIAGNOSIS >
ECU DIAGNOSIS A
Wiring Diagram INFOID:0000000005258613
B
SRC
ABHWA0072GB

< ECU DIAGNOSIS >
ABHWA0073GB

< ECU DIAGNOSIS >
SRC
ABHIA0197GB

< ECU DIAGNOSIS >
ABHIA0198GB

< ECU DIAGNOSIS >
SRC
ABHIA0199GB

< ECU DIAGNOSIS >
ABHIA0200GB

< ECU DIAGNOSIS >
SRC
ABHIA0201GB

< ECU DIAGNOSIS >
ABHIA0202GB

< ECU DIAGNOSIS >
SRC
ABHIA0203GB

< ECU DIAGNOSIS >
ABHIA0204GB

< ECU DIAGNOSIS >
SRC
ABHIA0205GB
Trouble Diagnosis with CONSULT-III INFOID:0000000005258614 P
DIAGNOSTIC CODE CHART

NOTE:
Follow the procedures in numerical order when repairing malfunctioning parts. Confirm whether malfunction is
eliminated using air bag warning lamp or CONSULT-III each time repair is finished. If malfunction is still
observed, proceed to the next step. When malfunction is eliminated, further repair work is not required.

< ECU DIAGNOSIS >

Driver air bag module circuit (DR1) is 1. Visually check the wiring harness connection.
B1049 open 2. Replace the harness if it has visible damage.
DRIVER AIRBAG MODULE (including the spiral cable). 3. Replace the driver air bag module.
[OPEN] 4. Replace the spiral cable.
B1054 open
[VB-SHORT] Driver air bag module circuit (DR2) is
[GND-SHORT] Driver air bag module circuit (DR2) is
Driver air bag module circuits (DR1) are
[SHORT] Driver air bag module circuits (DR2) are
Front passenger air bag module circuit 1. Visually check the wiring harness connection.
B1065
ASSIST A/B MODULE (AS1) is open. 2. Replace the harness if it has visible damage.
[OPEN] 3. Replace the front passenger air bag module.
(AS2) is open.
B1066 (AS1) is shorted to a power supply cir-
ASSIST A/B MODULE cuit.
[VB-SHORT] Front passenger air bag module circuit
B1071 (AS2) is shorted to a power supply cir-
cuit.
B1067
ASSIST A/B MODULE (AS1) is shorted to ground.
[GND-SHORT] Front passenger air bag module circuit
B1072
(AS2) is shorted to ground.
Front passenger air bag module circuits
B1068
ASSIST A/B MODULE (AS1) are shorted to each other.
[SHORT] Front passenger air bag module circuits
B1073
(AS2) are shorted to each other.
SIDE MODULE LH Front LH side air bag module circuit is 1. Visually check the wiring harness connection.
B1134
3. Replace the front LH seat back assembly.
B1136
SIDE MODULE LH Front LH side air bag module circuits are
B1137

< ECU DIAGNOSIS >
A
SIDE MODULE RH Front RH side air bag module circuit is 1. Visually check the wiring harness connection.
B1129
3. Replace the front RH seat back assembly.
B1130 4. Replace the air bag diagnosis sensor unit. B
B1131
SIDE MODULE RH Front RH side air bag module circuits C
B1132
[SHORT] are shorted to each other.
FR CURTN MODULE LH LH side curtain air bag module (front) 1. Visually check the wiring harness connection.
B1198
[OPEN] circuit is open. 2. Replace the harness if it has visible damage. D
LH side curtain air bag module (front)
FR CURTN MODULE LH 4. Replace the air bag diagnosis sensor unit.
B1199 circuit is shorted to a power supply cir-
[VB-SHORT] 5. Replace the related harness.
cuit. E
FR CURTN MODULE LH LH side curtain air bag module (front)
B1200
[GND-SHORT] circuit is shorted to ground.
FR CURTN MODULE LH
B1201
LH side curtain air bag module (front) F
[SHORT] circuits are shorted to each other.
FR CURTN MODULE RH RH side curtain air bag module (front) 1. Visually check the wiring harness connection.
B1193
[OPEN] circuit is open. 2. Replace the harness if it has visible damage.
G
RH side curtain air bag module (front)
FR CURTN MODULE RH 4. Replace the air bag diagnosis sensor unit.
cuit.
SRC
FR CURTN MODULE RH RH side curtain air bag module (front)
B1195
[GND-SHORT] circuit is shorted to ground.
FR CURTN MODULE RH RH side curtain air bag module (front)
[SHORT]
B1196
circuits are shorted to each other.
I
CURTAIN MODULE LH LH side curtain air bag module (rear) cir- 1. Visually check the wiring harness connection.
B1150
3. Replace the LH side curtain air bag module. J
B1152 K
B1153
L
CURTAIN MODULE RH RH side curtain air bag module (rear) 1. Visually check the wiring harness connection.
B1145
[OPEN] circuit is open. 2. Replace the harness if it has visible damage.
RH side curtain air bag module (rear)
CURTAIN MODULE RH 4. Replace the air bag diagnosis sensor unit. M
cuit.
CURTAIN MODULE RH RH side curtain air bag module (rear)
B1147
[GND-SHORT] circuit is shorted to ground. N
CURTAIN MODULE RH RH side curtain air bag module (rear)
B1148
[SHORT] circuits are shorted to each other.
PRE-TEN FRONT LH LH seat belt pre-tensioner circuit is 1. Visually check the wiring harness connection. O
B1086
3. Replace the front LH seat belt pre-tensioner.
PRE-TEN FRONT LH LH seat belt pre-tensioner circuit is
[VB-SHORT] shorted to a power supply circuit. P
PRE-TEN FRONT LH LH seat belt pre-tensioner circuit is
B1088
PRE-TEN FRONT LH LH seat belt pre-tensioner circuits are
B1089

< ECU DIAGNOSIS >
PRE-TEN FRONT RH RH seat belt pre-tensioner circuit is 1. Visually check the wiring harness connection.
B1081
3. Replace the front RH seat belt pre-tensioner.
PRE-TEN FRONT RH RH seat belt pre-tensioner circuit is
PRE-TEN FRONT RH RH seat belt pre-tensioner circuit is
B1083
PRE-TEN FRONT RH RH seat belt pre-tensioner circuits are
B1084
CRASH ZONE SEN B1033 Crash zone sensor has malfunctioned. 1. Visually check the wiring harness connection.
[UNIT FAIL] 2. Replace the harness if it has visible damage.
B1034
3. Replace the crash zone sensor.
CRASH ZONE SEN Crash zone sensor communication er- 4. Replace the air bag diagnosis sensor unit.
B1035
[COMM FAIL] ror. 5. Replace the related harness.
SATELLITE SENS LH B1118 LH side air bag satellite sensor has mal- 1. Visually check the wiring harness connection.
B1119
3. Replace the LH side air bag satellite sensor.
SATELLITE SENS LH LH side air bag satellite sensor commu- 4. Replace the air bag diagnosis sensor unit.
B1120
[COMM FAIL] nication error. 5. Replace the related harness.
SATELLITE SENS RH B1113 RH side air bag satellite sensor has mal- 1. Visually check the wiring harness connection.
B1114
3. Replace the RH side air bag satellite sensor.
SATELLITE SENS RH RH side air bag satellite sensor commu- 4. Replace the air bag diagnosis sensor unit.
B1115
[COMM FAIL] nication error. 5. Replace the related harness.
Air bag diagnosis sensor unit is malfunc- 1. Visually check the wiring harness connection.
tioning. 2. Replace the harness if it has visible damage.
CONTROL UNIT B1XXX
Front passenger air bag OFF indicator is 1. Visually check the wiring harness connection.
malfunctioning. 2. Replace the harness if it has visible damage.
3. Replace the front passenger air bag OFF in-
PASS A/B INDCTR CKT B1023
dicator.
B1017 The OCS control unit is malfunctioning. 1. Replace the RH front seat cushion assembly.
OCCUPANT SENS C/U Do not disassemble the seat cushion assem-
B1020
[UNIT FAIL] bly.
B1021
OCCUPANT SENS The OCS sensor is malfunctioning.
B1018
[UNIT FAIL]
The belt tension sensor is malfunction- 1. Visually check the wiring harness connection.
ing. 2. Replace the harness if it has visible damage.
3. Replace the RH front seat belt assembly.
BELT TENSION SENS
B1019 4. Replace the RH front seat cushion assembly.
[UNIT FAIL]
Do not disassemble the seat cushion assem-
bly.
Communication between the OCS con- 1. Visually check the wiring harness connection.
trol unit and the air bag diagnosis sensor 2. Replace the harness if it has visible damage.
unit is interrupted. 3. Replace the RH front seat cushion assembly.
OCCUPANT SENS C/U
B1022 Do not disassemble the seat cushion assem-
[COMM FAIL]
bly.
FRONTAL COLLISION DE- Driver and/or front passenger air bag Refer to SR-19, "For Frontal Collision".
B1209
TECTION modules are deployed.

< ECU DIAGNOSIS >
A
SIDE COLLISION DETEC- Side and/or curtain air bag modules are Refer to SR-20, "For Side and Rollover Collision".
B1210
TION deployed.
Curtain air bag module and seat belt
ROLLOVER DETECTION B1211 B
pre-tensioner are deployed.
Trouble Diagnosis without CONSULT-III INFOID:0000000005258615
C
WARNING LAMP FLASH CODE CHART
NOTE:
Follow the procedures in numerical order when repairing malfunctioning parts. Confirm whether malfunction is D
eliminated using air bag warning lamp each time repair is finished. If malfunction is still observed, proceed to
the next step. When malfunction is eliminated, further repair work is not required.
E
SHIA0026E
SRC
WHIA0260E
K
N
WHIA0198E
WHIA0261E

< ECU DIAGNOSIS >
WHIA0200E
WHIA0262E
WHIA0263E
WHIA0203E
WHIA0204E

< ECU DIAGNOSIS >
C
WHIA0264E
WHIA0265E
G
SRC
J
WHIA0255E
WHIA0253E
WHIA0254E

< ECU DIAGNOSIS >
WHIA0252E
WHIA0211E
WHIA0212E

SRS AIR BAG SYSTEM
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS A
SRS AIR BAG SYSTEM
"AIR BAG" Warning Lamp Does Not Turn Off INFOID:0000000005258616
B
1.CHECK CONDITION OF AIR BAG MODULE C
Inspect for any deployed air bag modules or seat belt pre-tensioners.
Are any air bag modules or seat belt pre-tensioners deployed?
D
YES >> Refer to SR-19, "For Frontal Collision" or SR-20, "For Side and Rollover Collision".
NO >> GO TO 2
2.CHECK THE AIR BAG FUSE E
Check 10A fuse [No. 13, located in the fuse block (J/B)].
Is the fuse blown?
YES >> GO TO 3 F
NO >> GO TO 4
3.CHECK AIR BAG FUSE AGAIN G
Replace 10A fuse [No. 13, located in the fuse block (J/B)] and turn ignition switch ON.
Does the fuse blow again?
YES >> Replace harness. SRC
4.CHECK AIR BAG DIAGNOSIS SENSOR UNIT
I
Connect CONSULT-III.
Is AIR BAG displayed on CONSULT-III?
YES >> GO TO 5 J
NO >> Visually inspect the air bag diagnosis sensor unit harness connections. If the connections are OK,
replace the air bag diagnosis sensor unit. Refer to SR-16, "Removal and Installation".
5.CHECK HARNESS CONNECTION K
Check for loose connections between the combination meter and the air bag diagnosis sensor unit.
Are there any loose connections?
YES >> Properly connect the combination meter and air bag diagnosis sensor unit harness connectors. If L
AIR BAG warning lamp still does not turn off, replace the wiring harness.
NO >> Replace air bag diagnosis sensor unit.
"AIR BAG" Warning Lamp Does Not Turn On INFOID:0000000005258617
M
N
1.CHECK METER FUSE
Check the 10A fuse [No. 14, located in the fuse block (J/B)] .
Is the fuse blown? O
YES >> GO TO 2
NO >> GO TO 3
2.REPLACE METER FUSE AND CHECK AGAIN P
Replace 10A fuse [No. 14, located in the fuse block (J/B)] and turn ignition switch ON.
Does the fuse blow again?
YES >> Replace harness.
3.CHECK HARNESS CONNECTIONS BETWEEN AIR BAG DIAGNOSIS SENSOR UNIT AND COMBINA-
SRS AIR BAG SYSTEM
TION METER
Inspect the harness and connectors between the air bag diagnosis sensor unit and the combination meter.
Do the harness or connectors have any visible damage?
YES >> Replace harness.
NO >> GO TO 4
4.CHECK COMBINATION METER
Disconnect the air bag diagnosis sensor unit harness connectors and turn ignition switch ON.
Does AIR BAG warning lamp turn on?
YES >> Replace the air bag diagnosis sensor unit. Refer to SR-16, "Removal and Installation".
NO >> Replace the combination meter. Refer to MWI-96, "Removal and Installation".

A
Seat Belt Warning System Does Not Function INFOID:0000000005258618
1.SEAT BELT WARNING LIGHT B

Does the seat belt warning lamp come ON?
C
YES >> GO TO 2
NO >> Check 10A fuse [No. 14, located in the fuse block (J/B)].
Check seat belt buckle switch LH.
Check harness between combination meter and seat belt buckle switch LH. D
Check combination meter. Refer to MWI-58, "Fail Safe".
2.SEAT BELT BUCKLE LH
E
Fasten the seat belt buckle LH.
Does the seat belt warning lamp go OFF?
YES >> GO TO 3 F
NO >> Check seat belt buckle switch LH.
Check harness between combination meter and seat belt buckle switch LH.
3.OCCUPANT CLASSIFICATION SYSTEM G
Have a helper sit in the passenger seat.
Does the seat belt warning lamp go ON?
YES >> GO TO 4 SRC
NO >> Check occupant classification system. Refer to SRC-10, "Occupant Classification System
(OCS)".
Check harness between occupant classification control unit and air bag diagnosis sensor unit. I
4.SEAT BELT BUCKLE RH
Fasten the seat belt buckle RH.
J
Does the seat belt warning lamp go OFF?
YES >> System OK.
NO >> Check seat belt buckle switch RH.
Check harness between seat belt buckle switch RH and air bag diagnosis sensor unit. K
Replace air bag diagnosis sensor unit. Refer to SR-16, "Removal and Installation".

PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000005484538
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for SRS "AIR BAG" and "SEAT BELT PRE-TENSIONER" Service
INFOID:0000000005258620
Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 min-
utes.
For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-
tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have
passed.
The air bag diagnosis sensor unit must always be installed with the arrow mark pointing toward the front
of the vehicle for proper operation. Also check air bag diagnosis sensor unit for cracks, deformities or rust
before installation and replace as required.
The spiral cable must be aligned with the neutral position since its rotations are limited. Do not attempt to
turn steering wheel or column after removal of steering gear.
Handle air bag module carefully. Always place driver and front passenger air bag modules with the pad side
facing upward and seat mounted front side air bag module standing with the stud bolt side facing down.
Conduct self-diagnosis to check entire SRS for proper function after replacing any components.
After air bag inflates, the front instrument panel assembly should be replaced if damaged.
Occupant Classification System Precaution INFOID:0000000005258621
Replace occupant classification system control unit and passenger front seat cushion as an assembly.

SRC PDF

Uploaded by

Copyright:

Available Formats

SRC PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SRC PDF

Uploaded by

Copyright:

Available Formats

RESTRAINTS

Revision: July 2009 SRC-1 2010 Pathfinder

Revision: July 2009 SRC-2 2010 Pathfinder

Revision: July 2009 SRC-3 2010 Pathfinder

Revision: July 2009 SRC-4 2010 Pathfinder

Revision: July 2009 SRC-5 2010 Pathfinder

Right side colli-

Revision: July 2009 SRC-6 2010 Pathfinder

Driver Air Bag Module INFOID:0000000005258546

Revision: July 2009 SRC-7 2010 Pathfinder

Front Side Air Bag INFOID:0000000005258548

Side Curtain Air Bag INFOID:0000000005258549

Front Seat Belt Pre-tensioner with Load Limiter INFOID:0000000005258550

Revision: July 2009 SRC-8 2010 Pathfinder

Revision: July 2009 SRC-9 2010 Pathfinder

Occupant Classification System (OCS) INFOID:0000000005258553

Seat occupied NOTE ON Deactivated (disabled) OFF

Revision: July 2009 SRC-10 2010 Pathfinder

Revision: July 2009 SRC-11 2010 Pathfinder

System Description INFOID:0000000005258555

Passenger Seat Belt Warning System Operation

Component Parts Location INFOID:0000000005258556

Refer to SRC-7, "SRS Component Parts Location".

Revision: July 2009 SRC-12 2010 Pathfinder

Revision: July 2009 SRC-13 2010 Pathfinder

Go to COLLISION DIAGNOSIS SR-

Air bag diagnosis sensor unit is mal-

Air bag diagnosis sensor unit is mal-

Revision: July 2009 SRC-14 2010 Pathfinder

Revision: July 2009 SRC-15 2010 Pathfinder

Revision: July 2009 SRC-16 2010 Pathfinder

DTC B1049 B1052, B1054 B1057 DRIVER AIRBAG MODULE

DTC DETECTION LOGIC

CONSULT-III name DTC DTC detecting condition Repair order

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

Recheck SRS after each replacement.

Revision: July 2009 SRC-18 2010 Pathfinder

Revision: July 2009 SRC-19 2010 Pathfinder

DTC B1065 B1068, B1070 B1073 PASSENGER AIR BAG MODULE

DTC DETECTION LOGIC

CONSULT-III name DTC DTC detecting condition Repair order

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

Revision: July 2009 SRC-21 2010 Pathfinder

Revision: July 2009 SRC-22 2010 Pathfinder

DTC B1134 B1137 FRONT LH SIDE AIR BAG MODULE B

DTC DETECTION LOGIC

CONSULT-III name DTC DTC detecting condition Repair order

DTC CONFIRMATION PROCEDURE (With CONSULT-lll) M

Check for the DTC on CONSULT-lll.

Recheck SRS after each replacement.

Revision: July 2009 SRC-25 2010 Pathfinder

DTC B1129 B1132 FRONT RH SIDE AIR BAG MODULE

DTC DETECTION LOGIC

CONSULT-III name DTC DTC detecting condition Repair order

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

Recheck SRS after each replacement.

Is there any visible damage to the connector?

4.AIR BAG DIAGNOSIS SENSOR UNIT

Revision: July 2009 SRC-28 2010 Pathfinder