Srs Airbag Control System: Section
Srs Airbag Control System: Section
E
CONTENTS
PRECAUTION ............................................... 3 SRS AIR BAG SYSTEM ................................... 23 F
SRC-1
Diagnosis Procedure .............................................. 47 B1411, B1412, B1413, B1414, B1415 AIR
BAG DIAGNOSIS SENSOR UNIT .................... 73
B0021 CURTAIN AIR BAG MODULE ............... 49 DTC Description ...................................................... 73
DTC Description ..................................................... 49
Diagnosis Procedure ............................................... 73
Diagnosis Procedure .............................................. 49
B1416, B1417, B1418, B1419, B1420 AIR
B0028 SIDE AIR BAG MODULE ....................... 51
BAG DIAGNOSIS SENSOR UNIT .................... 75
DTC Description ..................................................... 51
DTC Description ...................................................... 75
Diagnosis Procedure .............................................. 51
Diagnosis Procedure ............................................... 75
B0029 CURTAIN AIR BAG MODULE ............... 53
B1421 FRONTAL COLLISION DETECTION ... 77
DTC Description ..................................................... 53
DTC Description ...................................................... 77
Diagnosis Procedure .............................................. 53
Diagnosis Procedure ............................................... 77
B0091 B-PILLAR SATELLITE SENSOR .......... 55
B1422 SIDE COLLISION DETECTION ............. 78
DTC Description ..................................................... 55
DTC Description ...................................................... 78
Diagnosis Procedure .............................................. 55
Diagnosis Procedure ............................................... 78
B0094 CRASH ZONE SENSOR ........................ 57
B1425 REAR COLLISION DETECTION ........... 79
DTC Description ..................................................... 57
DTC Description ...................................................... 79
Diagnosis Procedure .............................................. 57
Diagnosis Procedure ............................................... 79
B0096 B-PILLAR SATELLITE SENSOR .......... 59
B1427 CONFIG SETTING ................................. 80
DTC Description ..................................................... 59
DTC Description ...................................................... 80
Diagnosis Procedure .............................................. 59
Diagnosis Procedure ............................................... 80
B00D2 FRONT PASSENGER AIR BAG ON
B142A IGN VOLTAGE ...................................... 81
INDICATOR ....................................................... 61 DTC Description ...................................................... 81
DTC Description ..................................................... 61 Diagnosis Procedure ............................................... 81
Diagnosis Procedure .............................................. 61
B1430 SEAT BELT PRE-TENSIONER ............. 83
B00D5 FRONT PASSENGER AIR BAG OFF DTC Description ...................................................... 83
INDICATOR ....................................................... 63 Diagnosis Procedure ............................................... 84
DTC Description ..................................................... 63
Diagnosis Procedure .............................................. 63 B1431 SEAT BELT PRE-TENSIONER ............. 85
DTC Description ...................................................... 85
B00DF AIR BAG CUTOFF SWITCH ................. 65 Diagnosis Procedure ............................................... 86
DTC Description ..................................................... 65
Diagnosis Procedure .............................................. 65 B1432 LAP PRE-TENSIONER .......................... 87
DTC Description ...................................................... 87
B0099 SATELLITE SENSOR ............................ 67 Diagnosis Procedure ............................................... 87
DTC Description ..................................................... 67
Diagnosis Procedure .............................................. 67 B1433 LAP PRE-TENSIONER .......................... 89
DTC Description ...................................................... 89
B1400, B1401, B1402, B1403, B1404, B1405 Diagnosis Procedure ............................................... 89
AIR BAG DIAGNOSIS SENSOR UNIT ............. 69
DTC Description ..................................................... 69 SYMPTOM DIAGNOSIS ............................ 91
Diagnosis Procedure .............................................. 69
SRS AIR BAG WARNING LAMP DOES NOT
B1406, B1407, B1408, B1409, B1410 AIR TURN OFF ......................................................... 91
BAG DIAGNOSIS SENSOR UNIT ..................... 71 Diagnosis Procedure ............................................... 91
DTC Description ..................................................... 71
Diagnosis Procedure .............................................. 71 SRS AIR BAG WARNING LAMP DOES NOT
TURN ON ........................................................... 92
Diagnosis Procedure ............................................... 92
SRC-2
PRECAUTIONS
< PRECAUTION >
PRECAUTION A
PRECAUTIONS
Precautions for Removing Battery Terminal INFOID:0000000010506943
B
• With the adoption of Auto ACC function, ACC power is automatically supplied by operating the intelligent key
or remote keyless entry or by opening/closing the driver side door. In addition, ACC power is supplied even
after the ignition switch is turned to the OFF position, i.e. ACC power is supplied for a certain fixed time. C
• When disconnecting the 12V battery terminal, turn off the ACC
power before disconnecting the 12V battery terminal, observing
“How to disconnect 12V battery terminal” described below. D
NOTE:
Some ECUs operate for a certain fixed time even after ignition
switch is turned OFF and ignition power supply is stopped. If the
battery terminal is disconnected before ECU stops, accidental DTC E
detection or ECU data damage may occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch. F
NOTE:
SEF289H
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC. G
NOTE:
The removal of 12V battery may cause a DTC detection error.
SRC
HOW TO DISCONNECT 12V BATTERY TERMINAL
Disconnect 12V battery terminal according to Instruction 1 or Instruction 2 described below.
For vehicles parked by ignition switch OFF, refer to Instruction 2.
I
INSTRUCTION 1
1. Open the hood.
2. Turn key switch to the OFF position with the driver side door opened. J
3. Get out of the vehicle and close the driver side door.
4. Wait at least 3 minutes. For vehicle with the engine listed below, remove the battery terminal after a lapse
of the specified time. K
SRC-3
PRECAUTIONS
< PRECAUTION >
CAUTION:
While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of
this caution results in the activation of ACC power supply according to the Auto ACC function.
6. Remove 12V battery terminal.
CAUTION:
After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000010506944
CAUTION:
Comply with the following cautions to prevent any error and malfunction.
• Before removing and installing any control units, first turn the ignition power source and accessory
power source to the OFF, then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect
both battery cables.
• Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing
work. If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Open driver door.
3. Turn the ignition switch to the ON position.
(At this time, the steering lock will be released.)
4. Turn the ignition switch to OFF position with driver door open.
5. Wait for 3 minutes or longer with driver door open.
NOTE:
• Do not close driver door because the steering wheel locks when driver door is closed.
• The auto acc function is adapted to this vehicle. For this reason, even when the ignition switch is turned
to OFF position, the accessory power source does not turned OFF and continues to be supplied for a
certain amount of time.
6. Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
7. Perform the necessary repair operation.
8. When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the ignition switch from OFF position to ON position, then to LOCK position. (The steering wheel will lock
when the ignition switch is turned to LOCK position.)
9. Perform self-diagnosis check of all control units using CONSULT.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000010434386
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
SRC-4
PRECAUTIONS
< PRECAUTION >
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag A
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
B
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING: C
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
D
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service. E
Service INFOID:0000000010377815
• Never use electrical test equipment to check SRS circuits unless instructed to in this Service Manual. F
• Before servicing the SRS, turn power switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre- G
tensioner to deploy. Therefore, never work on any SRS connectors or wires until at least 3 minutes have
passed.
• Diagnosis sensor unit must always be installed with their arrow marks “⇐” pointing towards the front of the
vehicle for proper operation. Also check diagnosis sensor unit for cracks, deformities or rust before installa- SRC
tion and replace as required.
• The spiral cable must be aligned with the neutral position since its rotations are limited. Never turn steering
wheel and column after removal of steering gear. I
• Handle air bag module carefully. Always place driver and front passenger air bag modules with the pad side
facing upward and seat mounted front side air bag module standing with the stud bolt side facing down.
• Conduct self-diagnosis to check entire SRS for proper function after replacing any components.
J
• After air bag inflates, the front instrument panel assembly should be replaced if damaged.
• Always replace instrument panel pad following front passenger air bag deployment.
• Never solder the harness when making repairs. Check that harness is not pinched and that there is no con-
tact with other components. K
• Never allow harness to come in contact with oil, grease, waste oil, or water.
• Never insert foreign materials, such as a screwdriver, into the harness connector. (This is to prevent acci-
dental activation caused by static electricity.) L
• Always use CONSULT or SRS air bag warning lamp to perform the circuit diagnosis. (Never use an electric
tester such as a circuit tester.)
SRC-5
COMPONENT PARTS
< SYSTEM DESCRIPTION >
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location INFOID:0000000010377816
JMHIA2895ZZ
SRC-6
COMPONENT PARTS
< SYSTEM DESCRIPTION >
Behind center pillar lower garnish Behind center pillar lower garnish View with steering wheel removed A
RH RH
View with center console assembly Behind center pillar lower garnish LH Behind center pillar lower garnish LH
B
No. Component Function
Curtain air bag module RH Refer to SRC-9, "Curtain air bag module".
C
Side air bag module RH Refer to SRC-8, "Side air bag module".
Driver air bag module Refer to SRC-7, "Driver air bag module".
Combination meter (air bag warning lamp) Refer to SRC-12, "Air bag warning lamp". D
Front passenger air bag OFF
Refer to SRC-13, "Front Passenger Air Bag Off Indicator".
indicator
Indicator unit E
Front passenger air bag ON
Refer to SRC-13, "Front Passenger Air Bag On Indicator".
indicator
Crash zone sensor Refer to SRC-11, "Crash zone sensor".
F
Passenger air bag module Refer to SRC-8, "Passenger air bag module".
Deactivates passenger air bag module deployment by switch-
Air bag cutoff switch
ing air bag cut OFF switch to the OFF position. G
Side air bag module LH Refer to SRC-8, "Side air bag module".
Curtain air bag module LH Refer to SRC-9, "Curtain air bag module".
SRC
Lap pre-tensioner RH Refer to SRC-10, "Double pre-tensioner seat belt".
Seat belt pre-tensioner RH Refer to SRC-9, "Seat belt pre-tensioner with Load limiter".
I
Satellite sensor RH Refer to SRC-12, "Satellite sensor".
Air bag diagnosis sensor unit Refer to SRC-12, "Air bag diagnosis sensor unit". J
Seat belt pre-tensioner LH Refer to SRC-9, "Seat belt pre-tensioner with Load limiter".
JMHIA1121ZZ
P
SRC-7
COMPONENT PARTS
< SYSTEM DESCRIPTION >
• Driver air bag inflates by breaking steering wheel center pad sur-
face .
JMHIA2480ZZ
JMHIA0155ZZ
JMHIA2207ZZ
NNHIA0030ZZ
SRC-8
COMPONENT PARTS
< SYSTEM DESCRIPTION >
• Identification mark is installed to seatback side stitch indicating
that side air bag is equipped. A
• Side air bag inflates through seatback side stitch .
JMHIA2237ZZ
D
Curtain air bag module INFOID:0000000010513111
• Curtain air bag module is built into roof side portion LH and RH.
• Curtain air bag module mainly consists of air bag and inflator which inflates air bag. E
SRC
JMHIA2866ZZ
J
• Identification mark is installed to center pillar upper garnish upper indicating that SRS curtain air bag is
equipped.
• Curtain air bag inflates through a space between headliner and roof side portion. K
JMHIA2867ZZ
P
Seat belt pre-tensioner with Load limiter INFOID:0000000010513117
DESCRIPTION
The seat belt system is equipped with pre-tensioner mechanism, load limiter mechanism, and ELR mecha-
nism (front seat passenger restraint mechanism).
STRUCTURE
SRC-9
COMPONENT PARTS
< SYSTEM DESCRIPTION >
JMHIA0167ZZ
PRE-TENSIONER MECHANISM
• In a frontal collision that exceeds the specified limit, air bag sensor
unit detects the collision, transmits an electrical signal to gas gen-
erator in manifold case, and activates gas generator. Gas is
generated.
• The pressure of the generated gas moves the ball inside of pipe
. The ball then presses ring gear which is engaged to the pin-
ion gear .
• The rotation of the ring gear rotates the shaft in the retracting
direction of the seat belt. Seat belt is retracted.
JMHIA0168ZZ
JMHIA0169ZZ
DESCRIPTION
The system combines lap pre-tensioner mechanism for lumbar seat belt and pre-tensioner seat belt with load
limiter. The system upgrades passenger restraint by reducing lumbar movement during a frontal collision.
LAP PRE-TENSIONER MECHANISM
• In a frontal collision that exceeds the specified limit, air bag sensor unit detects the collision, transmits an
electrical signal to gas generator in pipe, and activates gas generator. Gas is generated. The pressure of
the generated gas moves the piston inside of pipe toward pipe front direction, and retracts wire.
• Lap anchor is installed to end of the wire and end of seat belt is connected to lap anchor. The wire therefore
retracts seat belt.
SRC-10
COMPONENT PARTS
< SYSTEM DESCRIPTION >
• When piston stops, clutch mechanism integrated to piston prevents piston from moving in the original direc-
tion. Wire and lap anchor therefore remain in the retracted status. A
F
PHIA1226J
K
NNHIA0038ZZ
JMHIA2871ZZ
SRC-11
COMPONENT PARTS
< SYSTEM DESCRIPTION >
Satellite sensor INFOID:0000000010513114
• Air bag diagnosis sensor unit is installed to front seat center por-
tion (under center console). Air bag diagnosis sensor unit inte-
grates control functions of driver air bag, passenger air bag, side
air bag, curtain air bag, and seat belt pre-tensioner.
: Vehicle front
• Air bag diagnosis sensor unit integrates frontal collision “G” sensor,
frontal collision safing sensor, and lateral collision safing sensor
(only for models with curtain air bag).
• Air bag diagnosis sensor unit has a function that judges impact due
to frontal and lateral collisions exceeding the specified limit of the JMHIA2873ZZ
vehicle. Air bag diagnosis sensor unit also has an auxiliary power
supply function that supplements battery power supply in the event battery is damaged in a collision.
• Air bag diagnosis sensor unit diagnoses electric system of entire system. Self-diagnosis function is adopted,
which indicates system malfunction by turning ON air bag warning lamp on combination meter when a mal-
function is detected. Diagnosis using CONSULT is possible.
Air bag warning lamp INFOID:0000000010513116
SRC-12
COMPONENT PARTS
< SYSTEM DESCRIPTION >
Front Passenger Air Bag Off Indicator INFOID:0000000010435464
A
Front passenger air bag OFF indicator turns ON when turning air
bag cutoff switch OFF position.
B
D
JSHIA0048ZZ
SRC
JSHIA0049ZZ
SRC-13
SYSTEM
< SYSTEM DESCRIPTION >
SYSTEM
System Description INFOID:0000000010377817
SYSTEM DIAGRAM
JMHIA2896GB
SYSTEM DESCRIPTION
Supplemental Restraint System (SRS) activates air bag module and seat belt pre-tensioner when it detects a
frontal collision or a side collision that is more than the specified limit. Together with other safety devices, it
SRC-14
SYSTEM
< SYSTEM DESCRIPTION >
reduces the impact that occupant receives when vehicle collision occurs. Air bag diagnosis sensor unit sup-
plies power supply to air bag module and pre-tensioner seat belt when deceleration that is more than the A
specified limit is detected by G sensor in air bag diagnosis sensor unit, crash zone sensor, satellite sensor. Air
bag module is composed of electric igniter (squib), filter, pyrotechnic material, and gas generating material.
When air bag module receives a signal from air bag diagnosis sensor unit, air bag module ignites pyrotechnic
B
material using electric igniter (squib) so that gas generating material generates high temperature nitrogen gas.
The gas through filter activates air bag. At the same time, pre-tensioner seat belt receives power supply from
air bag diagnosis sensor unit, gas generator is activated, and then gas is generated. Balls in pipe are moved
according to generated gas pressure and strike pinion gear on ELR shaft. ELR shaft rotates and retracts seat C
belt.
AIR BAG DIAGNOSIS SENSOR UNIT FUNCTIONS
Air bag diagnosis sensor unit has the following functions. D
• Detects a collision and supplies the energy for deploying air bag and seat belt pre-tensioner.
• Detects and records electrical malfunction in air bag system and seat belt pre-tensioner system, and turns
air bag warning lamp ON. E
• Detects and records the deployment of air bag and seat belt pre-tensioner, and turns ON air bag warning
lamp.
• Indicates the malfunction record via CONSULT.
• Transmits car crash information signal to BCM when a collision is detected (collision detection output func- F
tion).
Air Bag Warning Lamp
G
• Detects electrical malfunction in air bag system and seat belt pre-tensioner system, and turns air bag warn-
ing lamp ON.
• Detects deployment malfunction in air bag system and seat belt pre-tensioner system, and turns air bag
warning lamp ON. SRC
• Air bag diagnosis sensor unit warns the driver by turning air bag warning lamp ON when air bag diagnosis
sensor unit detects battery low voltage. Air bag warning lamp turns ON when a voltage value at which air
bag diagnosis sensor unit cannot operate normally (9 V or less) is detected for 10 seconds or more. After I
starting to turn ON, air bag warning lamp turns OFF when air bag diagnosis sensor unit detects the normal
value of battery voltage for 10 seconds or more. The mode cannot be switched to diagnosis mode by ignition
switch while air bag warning lamp turns ON due to this cause.
• Air bag diagnosis sensor unit warns the driver by turning air bag warning lamp ON when air bag diagnosis J
sensor unit detects battery high voltage. Air bag warning lamp turns ON when a voltage value at which air
bag diagnosis sensor unit cannot operate normally (16 V or more) is detected for 3 seconds or more. After
starting to turn ON, air bag warning lamp turns OFF when air bag diagnosis sensor unit detects the normal K
value of battery voltage for 3 seconds or more. The mode cannot be switched to diagnosis mode by ignition
switch while air bag warning lamp turns ON due to this cause.
L
SRC-15
SYSTEM
< SYSTEM DESCRIPTION >
No malfunction is detected
SHIA0011E
SHIA0013E
SHIA0014E
COLLISION MODES
The operation of SRS is different depending on the collision modes applications. For example, the driver air
bag module, passenger air bag module, seat belt pre-tensioner and lap pre-tensioner are activated in a frontal
collision.
SRS configurations that are activated for the following collision modes.
×: Apply —: Not apply
SRS configuration Frontal collision Rear collision Left side collision Right side collision
Driver air bag module × — —*1 —*1
Passenger air bag module × — —*1 —*1
Seat belt pre-tensioner LH × —*1 —*1 —*1
Seat belt pre-tensioner RH × —*1 —*1 —*1
Lap pre-tensioner LH × —*1 —*1 —*1
Lap pre-tensioner RH × —*1 —*1 —*1
Side air bag module LH —*2 — × —*2
Side air bag module RH —*3 — —*3 ×
SRC-16
SYSTEM
< SYSTEM DESCRIPTION >
SRS configuration Frontal collision Rear collision Left side collision Right side collision
A
Curtain air bag module RH —*3 — —*3 ×
Collision detection output function × × × ×
*1: SRS may be activated when an excessive impact is applied toward the front of the vehicle. B
*2: SRS may be activated when an excessive impact is applied toward the left of the vehicle.
*3: SRS may be activated when an excessive impact is applied toward the right of the vehicle.
PASSENGER AIR BAG CUTOFF FUNCTION C
The passenger air bag module can change ON/OFF of the function by operating passenger air bag cutoff
switch. The passenger air bag cutoff switch is located in the left side of glove box. The indicators in indicator
unit turn on/off according to the passenger air bag cutoff switch state. D
• When passenger air bag cutoff switch is turned to the ON position, the passenger air bag module is enabled
and could inflate for certain types of collision. And front passenger air bag on indicator turn on.
• When the switch is turned to the OFF position, the passenger air bag module is disabled and will not inflate.
And front passenger air bag off indicator turn on. E
NOTE:
The driver side air bag module always reminds enabled and is not affected by the passenger air bag cutoff
switch. F
SRC
SRC-17
DIAGNOSIS SYSTEM (AIR BAG)
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (AIR BAG)
CONSULT Function INFOID:0000000010377821
APPLICATION ITEM
CONSULT performs the following functions.
SELF-DIAG RESULT
Refer to SRC-19, "DTC Index".
SRC-18
DIAGNOSIS SENSOR UNIT
< ECU DIAGNOSIS INFORMATION >
ECU DIAGNOSIS INFORMATION A
DIAGNOSIS SENSOR UNIT
DTC Index INFOID:0000000010377822
B
SRC-19
DIAGNOSIS SENSOR UNIT
< ECU DIAGNOSIS INFORMATION >
DTC Diagnostic item Reference page
B0091–11
B0091–23
B0091–24
B0091–25
B0091–28 B-PILLAR SAT SEN LH SRC-55, "DTC Description"
B0091–81
B0091–86
B0091–88
B0091–93
B0094–11
B0094–23
B0094–24
B0094–25
B0094–28 CRASH ZONE SENS SRC-57, "DTC Description"
B0094–81
B0094–86
B0094–88
B0094–93
B0096–11
B0096–23
B0096–24
B0096–25
B0096–28 B-PILLAR SAT SEN RH SRC-59, "DTC Description"
B0096–81
B0096–86
B0096–88
B0096–93
B00D2–04
B00D2–11
B00D2–12 PASS A/B ON INDCTR CIRC SRC-61, "DTC Description"
B00D2–13
B00D2–15
B00D5–04
B00D5–11
B00D5–12 PASS A/B ON INDCTR CIRC SRC-63, "DTC Description"
B00D5–13
B00D5–15
B00DF–52 PASS A/B DEACT SW SRC-65, "DTC Description"
SRC-20
DIAGNOSIS SENSOR UNIT
< ECU DIAGNOSIS INFORMATION >
DTC Diagnostic item Reference page
A
B0099–11
B0099–23
B0099–24 B
B0099–25
B0099–28 SATELLITE SENSOR SRC-67, "DTC Description"
B0099–81 C
B0099–86
B0099–88
D
B0099–93
B1400–00
B1401–00 E
B1402–00
CONTROL UNIT SRC-69, "DTC Description"
B1403–00
F
B1404–00
B1405–00
B1406–00 G
B1407–00
B1408–00 CONTROL UNIT SRC-71, "DTC Description"
SRC
B1409–00
B1410–00
B1411–00 I
B1412–00
B1413–00 CONTROL UNIT SRC-73, "DTC Description"
B1414–00
J
B1415–00
B1416–00
K
B1417–00
B1418–00 CONTROL UNIT SRC-75, "DTC Description"
B1419–00 L
B1420–00
B1421–00 FRONTAL COLLISION SRC-77, "DTC Description"
M
B1422–00 SIDE COLLISION SRC-78, "DTC Description"
B1425–00 REAR COLLISION SRC-79, "DTC Description"
B1427–54 N
CONFIG SETTING SRC-80, "DTC Description"
B1427–55
B142A–16
IGNITION VOLTAGE SRC-81, "DTC Description" O
B142A–17
B1430–09
B1430–11 P
B1430–12 PRE-TEN FRONT LH SRC-83, "DTC Description"
B1430–13
B1430–1A
SRC-21
DIAGNOSIS SENSOR UNIT
< ECU DIAGNOSIS INFORMATION >
DTC Diagnostic item Reference page
B1431–09
B1431–11
B1431–12 PRE-TEN FRONT RH SRC-85, "DTC Description"
B1431–13
B1431–1A
B1432–09
B1432–11
B1432–12 PRE-TEN FRONT LH 2 SRC-87, "DTC Description"
B1432–13
B1432–1A
B1433–09
B1433–11
B1433–12 PRE-TEN FRONT RH 2 SRC-89, "DTC Description"
B1433–13
B1433–1A
SRC-22
SRS AIR BAG SYSTEM
< WIRING DIAGRAM >
WIRING DIAGRAM A
SRS AIR BAG SYSTEM
LHD
B
LHD : Wiring Diagram INFOID:0000000010377823
SRC
JRHWC1560GB
SRC-23
SRS AIR BAG SYSTEM
< WIRING DIAGRAM >
JRHWC1828GB
SRC-24
SRS AIR BAG SYSTEM
< WIRING DIAGRAM >
SRC
JRHWC1577GB
SRC-25
SRS AIR BAG SYSTEM
< WIRING DIAGRAM >
JRHWC1578GB
SRC-26
SRS AIR BAG SYSTEM
< WIRING DIAGRAM >
SRC
JRHWC1579GB
SRC-27
SRS AIR BAG SYSTEM
< WIRING DIAGRAM >
JRHWC1580GB
RHD
SRC-28
SRS AIR BAG SYSTEM
< WIRING DIAGRAM >
RHD : Wiring Diagram INFOID:0000000010502954
SRC
JRHWC1562GB
P
SRC-29
SRS AIR BAG SYSTEM
< WIRING DIAGRAM >
JRHWC1563GB
SRC-30
SRS AIR BAG SYSTEM
< WIRING DIAGRAM >
SRC
JRHWC1581GB
SRC-31
SRS AIR BAG SYSTEM
< WIRING DIAGRAM >
JRHWC1582GB
SRC-32
SRS AIR BAG SYSTEM
< WIRING DIAGRAM >
SRC
JRHWC1583GB
SRC-33
SRS AIR BAG SYSTEM
< WIRING DIAGRAM >
JRHWC1584GB
SRC-34
DIAGNOSIS AND REPAIR WORK FLOW
< BASIC INSPECTION >
BASIC INSPECTION A
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow INFOID:0000000010431027
B
OVERALL SEQUENCE
C
SRC
JMHIA2620GB
DETAILED FLOW
SRC-35
DIAGNOSIS AND REPAIR WORK FLOW
< BASIC INSPECTION >
1.GET INFORMATION FOR SYMPTOM
1. Get detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurs).
2. Check operation condition of the function that is malfunctioning.
>> GO TO 2.
2.CHECK DTC
1. Check DTC.
2. Perform the following procedure if DTC is detected.
- Record DTC (Print them out using CONSULT).
- Erase DTC.
- Study the relationship between the cause detected by DTC and the symptom described by the customer.
3. Check related service bulletins for information.
Are any symptoms described and any DTC detected?
Symptom is described, DTC is detected>>GO TO 3.
Symptom is described, DTC is not detected>>GO TO 4.
Symptom is not described, DTC is detected>>GO TO 5.
3.CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
4.CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.
5.PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC CONFIRMATION PROCEDURE for the detected DTC, and then check that DTC is detected
again.
Is DTC detected?
YES >> GO TO 7.
NO >> Check according to GI-41, "Intermittent Incident".
6.DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS
Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step
4, and determine the trouble diagnosis order based on possible causes and symptom.
>> GO TO 7.
7.DETECT MALFUNCTIONING PART BY DIAGNOSIS PROCEDURE
Inspect according to Diagnosis Procedure of the system.
Is malfunctioning part detected?
YES >> GO TO 8.
NO >> Check according to GI-41, "Intermittent Incident".
8.REPAIR OR REPLACE THE MALFUNCTIONING PART
1. Repair or replace the malfunctioning part.
2. Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replace-
ment.
3. Check DTC. If DTC is detected, erase it.
SRC-36
DIAGNOSIS AND REPAIR WORK FLOW
< BASIC INSPECTION >
>> GO TO 9.
9.FINAL CHECK A
When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the
malfunction is repaired securely.
B
When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the
symptom is not detected.
Is DTC detected and does symptom remain?
C
YES-1 >> DTC is detected: GO TO 7.
YES-2 >> Symptom remains: GO TO 4.
NO >> Before returning the vehicle to the customer, always erase DTC.
D
SRC
SRC-37
ADDITIONAL SERVICE WHEN REPLACING AIR BAG DIAGNOSIS SENSOR
UNIT
< BASIC INSPECTION >
ADDITIONAL SERVICE WHEN REPLACING AIR BAG DIAGNOSIS SEN-
SOR UNIT
Description INFOID:0000000010431028
BEFORE REPLACEMENT
When replacing air bag diagnosis sensor unit, save or print current vehicle specification with CONSULT con-
figuration before replacement.
NOTE:
If “Before Replace ECU” of “Read / Write Configuration” cannot be used, use the “Manual Configuration” after
replacing air bag diagnosis sensor unit.
AFTER REPLACEMENT
CAUTION:
Follow the instructions listed below. Failure to do this may cause malfunctions to the air bag diagno-
sis sensor unit.
• Never perform “Read / Write Configuration” or “Manual Configuration” except for new air bag diag-
nosis sensor unit.
• When replacing air bag diagnosis sensor unit, you must perform “Read / Write Configuration” or
“Manual Configuration” with CONSULT.
• Complete the procedure of “Read / Write Configuration” or “Manual Configuration” in order.
• If you set incorrect “Read / Write Configuration” or “Manual Configuration”, incidents might occur.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
Work Procedure INFOID:0000000010431029
>> GO TO 2.
2.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
>> GO TO 3.
3.WRITING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “After Replace ECU” of “Read / Write Configuration” or “Manual Configuration” to write vehicle speci-
fication. Refer to SRC-39, "Work Procedure".
SRC-38
CONFIGURATION (AIR BAG DIAGNOSIS SENSOR UNIT)
< BASIC INSPECTION >
CONFIGURATION (AIR BAG DIAGNOSIS SENSOR UNIT)
A
Work Procedure INFOID:0000000010431030
>> GO TO 4.
3.PERFORM “MANUAL CONFIGURATION” F
CONSULT Configuration
1. Select “Manual Configuration”. G
2. Touch “Next”.
3. Select the “Type ID” searched by using FAST (service parts catalogue) to write the “Type ID” into the air
bag diagnosis sensor unit.
4. Touch “OK”. SRC
5. Check that the configuration has been successfully written and touch “End”.
>> GO TO 4. I
4.CHECK ALL ECU SELF-DIAGNOSIS RESULTS
1. Erase all ECU self-diagnosis results using CONSULT. J
2. Turn the ignition switch OFF.
3. Turn the ignition switch ON.
4. Check that all ECU self-diagnosis results have no DTC.
K
SRC-39
U1000 CAN COMM CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM CIRCUIT
Description INFOID:0000000010377825
CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Modern
vehicle is equipped with many electronic control unit, and each control unit shares information and links with
other control units during operation (not independent). In CAN communication, control units are connected
with 2 communication lines (CAN H-line, CAN L-line) allowing a high rate of information transmission with less
wiring. Each control unit transmits/receives data but selectively reads required data only.
CAN Communication Signal Chart. Refer to LAN-39, "CAN COMMUNICATION SYSTEM : CAN System Spec-
ification Chart".
DTC Logic INFOID:0000000010377826
POSSIBLE CAUSE
CAN communication system
FAIL-SAFE
—
Diagnosis Procedure INFOID:0000000010377827
SRC-40
U1010 CONTROL UNIT (CAN)
< DTC/CIRCUIT DIAGNOSIS >
U1010 CONTROL UNIT (CAN)
A
DTC Logic INFOID:0000000010377828
POSSIBLE CAUSE D
Air bag diagnosis sensor unit
FAIL-SAFE
E
—
Diagnosis Procedure INFOID:0000000010377829
F
1.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
When DTC “U1010–49” is detected, replace Air bag diagnosis sensor unit.
G
>> Replace Air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
SRC
SRC-41
B0001 DRIVER AIR BAG MODULE
< DTC/CIRCUIT DIAGNOSIS >
B0001 DRIVER AIR BAG MODULE
DTC Description INFOID:0000000010431038
POSSIBLE CAUSE
[B0001–00, B0001–09, B0001–1A]
• Connection malfunction or short circuit of harness and connector
• Internal malfunction of driver air bag module
• Internal malfunction of air bag diagnosis sensor unit
[B0001–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of driver air bag module
• Internal malfunction of air bag diagnosis sensor unit
[B0001–12]
• Connection malfunction or short circuit to power supply of harness and connector
• Internal malfunction of driver air bag module
• Internal malfunction of air bag diagnosis sensor unit
[B0001–13]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of driver air bag module
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected?
YES >> Refer to SRC-42, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure INFOID:0000000010431039
WARNING:
SRC-42
B0001 DRIVER AIR BAG MODULE
< DTC/CIRCUIT DIAGNOSIS >
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.) A
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
B
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
C
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals. D
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness. E
3.CHECK DTC
Perform each inspection according to the displayed DTC. F
Which DTC is displayed?
[B0001–13]>> GO TO 4.
[B0001–12]>> GO TO 8. G
[B0001–09]>> GO TO 5.
[B0001–00, B0001–09, B0001–1A]>> GO TO 6.
4.CHECK SPIRAL CABLE CIRCUIT 1 SRC
1. Turn ignition switch OFF.
2. Disconnect driver air bag module connector and combination switch (spiral cable) connector.
3. Check continuity between spiral cable terminals. I
Terminal Continuity
13 17 J
Existed
14 18
Is the inspection result normal?
K
YES >> GO TO 9.
NO >> Replace spiral cable. Refer to SR-17, "Removal and Installation".
5.CHECK SPIRAL CABLE CIRCUIT 2 L
1. Turn ignition switch OFF.
2. Disconnect driver air bag module connector and combination switch (spiral cable) connector.
3. Check continuity between spiral cable terminal and ground. M
Terminal Continuity
13 Ground N
Not existed
14
Is the inspection result normal?
O
YES >> GO TO 9.
NO >> Replace spiral cable. Refer to SR-17, "Removal and Installation".
6.CHECK SPIRAL CABLE CIRCUIT 3 P
1. Turn ignition switch OFF.
2. Disconnect driver air bag module harness connector and combination switch (spiral cable) harness con-
nector.
3. Check continuity between spiral cable terminals.
SRC-43
B0001 DRIVER AIR BAG MODULE
< DTC/CIRCUIT DIAGNOSIS >
Terminal Continuity
13 14 Not existed
Is the inspection result normal?
YES >> GO TO 7.
NO >> Replace spiral cable. Refer to SR-17, "Removal and Installation".
7.CHECK SPIRAL CABLE CIRCUIT 4
Check continuity between spiral cable terminals.
Terminal Continuity
17 18 Not existed
Is the inspection result normal?
YES >> GO TO 9.
NO >> Replace spiral cable. Refer to SR-17, "Removal and Installation".
8.REPLACE SPIRAL CABLE
1. Replace spiral cable. Refer to SR-17, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-42, "DTC Description".
Is DTC detected?
YES >> GO TO 9.
NO >> INSPECTION END
9.REPLACE DRIVER AIR BAG MODULE
1. Replace driver air bag module. Refer to SR-14, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-42, "DTC Description".
Is DTC detected?
YES >> GO TO 10.
NO >> INSPECTION END
10.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-42, "DTC Description".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
SRC-44
B0010 PASSENGER AIR BAG MODULE
< DTC/CIRCUIT DIAGNOSIS >
B0010 PASSENGER AIR BAG MODULE
A
DTC Description INFOID:0000000010431040
[B0010–12]
• Connection malfunction or short circuit to power supply of harness and connector
I
• Internal malfunction of passenger air bag module
• Internal malfunction of air bag diagnosis sensor unit
[B0010–13] J
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of passenger air bag module
• Internal malfunction of air bag diagnosis sensor unit
K
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE L
1.CHECK SELF-DIAG RESULT
With CONSULT M
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected? N
YES >> Refer to SRC-45, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
O
Diagnosis Procedure INFOID:0000000010431041
WARNING: P
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
SRC-45
B0010 PASSENGER AIR BAG MODULE
< DTC/CIRCUIT DIAGNOSIS >
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE PASSENGER AIR BAG MODULE
1. Replace passenger air bag module. Refer to SR-19, "Removal and Installation"
2. Perform DTC confirmation procedure. Refer to SRC-45, "DTC Description".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-45, "DTC Description".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
SRC-46
B0020 SIDE AIR BAG MODULE
< DTC/CIRCUIT DIAGNOSIS >
B0020 SIDE AIR BAG MODULE
A
DTC Description INFOID:0000000010431042
[B0020–12]
• Connection malfunction or short circuit to power supply of harness and connector
I
• Internal malfunction of side air bag module LH
• Internal malfunction of air bag diagnosis sensor unit
[B0020–13] J
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of side air bag module LH
• Internal malfunction of air bag diagnosis sensor unit
K
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE L
1.CHECK SELF-DIAG RESULT
With CONSULT M
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected? N
YES >> Refer to SRC-47, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
O
Diagnosis Procedure INFOID:0000000010431043
WARNING: P
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
SRC-47
B0020 SIDE AIR BAG MODULE
< DTC/CIRCUIT DIAGNOSIS >
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE SIDE AIR BAG MODULE LH
1. Replace side air bag module LH. Refer to SR-23, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-47, "DTC Description".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-47, "DTC Description".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
SRC-48
B0021 CURTAIN AIR BAG MODULE
< DTC/CIRCUIT DIAGNOSIS >
B0021 CURTAIN AIR BAG MODULE
A
DTC Description INFOID:0000000010431044
[B0021–11]
• Connection malfunction or short circuit to ground of harness and connector
I
• Internal malfunction of curtain air bag module LH
• Internal malfunction of air bag diagnosis sensor unit
[B0021–09, B0021–1A] J
• Connection malfunction or short circuit of harness and connector
• Internal malfunction of curtain air bag module LH
• Internal malfunction of air bag diagnosis sensor unit
K
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE L
1.CHECK SELF-DIAG RESULT
With CONSULT M
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected? N
YES >> Refer to SRC-49, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
O
Diagnosis Procedure INFOID:0000000010431045
WARNING: P
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
SRC-49
B0021 CURTAIN AIR BAG MODULE
< DTC/CIRCUIT DIAGNOSIS >
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE CURTAIN AIR BAG MODULE LH
1. Replace curtain air bag module LH. Refer to SR-21, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-49, "DTC Description".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-49, "DTC Description".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
SRC-50
B0028 SIDE AIR BAG MODULE
< DTC/CIRCUIT DIAGNOSIS >
B0028 SIDE AIR BAG MODULE
A
DTC Description INFOID:0000000010431046
[B0028–12]
• Connection malfunction or short circuit to power supply of harness and connector
I
• Internal malfunction of side air bag module RH
• Internal malfunction of air bag diagnosis sensor unit
[B0028–13] J
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of side air bag module RH
• Internal malfunction of air bag diagnosis sensor unit
K
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE L
1.CHECK SELF-DIAG RESULT
With CONSULT M
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected? N
YES >> Refer to SRC-51, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
O
Diagnosis Procedure INFOID:0000000010431047
WARNING: P
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
SRC-51
B0028 SIDE AIR BAG MODULE
< DTC/CIRCUIT DIAGNOSIS >
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE SIDE AIR BAG MODULE RH
1. Replace side air bag module RH. Refer to SR-23, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-51, "DTC Description".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-51, "DTC Description".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
SRC-52
B0029 CURTAIN AIR BAG MODULE
< DTC/CIRCUIT DIAGNOSIS >
B0029 CURTAIN AIR BAG MODULE
A
DTC Description INFOID:0000000010431048
[B0029–12]
• Connection malfunction or short circuit to power supply of harness and connector
I
• Internal malfunction of curtain air bag module RH
• Internal malfunction of air bag diagnosis sensor unit
[B0029–13] J
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of curtain air bag module RH
• Internal malfunction of air bag diagnosis sensor unit
K
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE L
1.CHECK SELF-DIAG RESULT
With CONSULT M
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected? N
YES >> Refer to SRC-53, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
O
Diagnosis Procedure INFOID:0000000010431049
WARNING: P
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
SRC-53
B0029 CURTAIN AIR BAG MODULE
< DTC/CIRCUIT DIAGNOSIS >
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE CURTAIN AIR BAG MODULE RH
1. Replace curtain air bag module RH. Refer to SR-21, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-53, "DTC Description".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-53, "DTC Description".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
SRC-54
B0091 B-PILLAR SATELLITE SENSOR
< DTC/CIRCUIT DIAGNOSIS >
B0091 B-PILLAR SATELLITE SENSOR
A
DTC Description INFOID:0000000010431050
POSSIBLE CAUSE G
[B0091–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of satellite sensor LH SRC
• Internal malfunction of air bag diagnosis sensor unit
[B0091–23, B0091–24, B0091–25, B0091–28
• Internal malfunction of satellite sensor LH I
• Internal malfunction of air bag diagnosis sensor unit
[B0091–81, B0091–93]
• Connection malfunction of harness or connector J
• Internal malfunction of satellite sensor LH
• Internal malfunction of air bag diagnosis sensor unit
K
[B0091–86]
• Air bag diagnosis sensor unit and satellite sensor LH is different from the part specified
[B0091–88] L
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of satellite sensor LH
• Internal malfunction of air bag diagnosis sensor unit
M
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE N
1.CHECK SELF-DIAG RESULT
With CONSULT O
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected? P
YES >> Refer to SRC-55, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure INFOID:0000000010431051
WARNING:
SRC-55
B0091 B-PILLAR SATELLITE SENSOR
< DTC/CIRCUIT DIAGNOSIS >
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK DTC
Perform each inspection according to the displayed DTC.
Which DTC is displayed?
[B0091–86]>> GO TO 4.
Other than the above>> GO TO 2.
2.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace harness connector.
3.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace wiring harness.
4.REPLACE SATELLITE SENSOR LH
1. Replace satellite sensor LH. Refer to SR-26, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-55, "DTC Description".
Is DTC detected?
YES >> GO TO 5.
NO >> INSPECTION END
5.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-55, "DTC Description".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
SRC-56
B0094 CRASH ZONE SENSOR
< DTC/CIRCUIT DIAGNOSIS >
B0094 CRASH ZONE SENSOR
A
DTC Description INFOID:0000000010431052
POSSIBLE CAUSE G
[B0094–81, B0094–93]
• Connection malfunction of harness or connector
• Internal malfunction of crash zone sensor SRC
• Internal malfunction of air bag diagnosis sensor unit
[B0094–88]
• Connection malfunction or open circuit of harness and connector I
• Internal malfunction of crash zone sensor
• Internal malfunction of air bag diagnosis sensor unit
J
[B0094–86]
• Air bag diagnosis sensor unit and crash zone sensor is different from the part specified
[B0094–23, B0094–24, B0094–25, B0094–28] K
• Internal malfunction of crash zone sensor
• Internal malfunction of air bag diagnosis sensor unit
[B0094–11] L
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of crash zone sensor
• Internal malfunction of air bag diagnosis sensor unit
M
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE N
1.CHECK SELF-DIAG RESULT
With CONSULT O
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected? P
YES >> Refer to SRC-57, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure INFOID:0000000010431053
WARNING:
SRC-57
B0094 CRASH ZONE SENSOR
< DTC/CIRCUIT DIAGNOSIS >
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK DTC
Perform each inspection according to the displayed DTC.
Which DTC is displayed?
[B0094–86]>> GO TO 4.
Other than the above>> GO TO 2.
2.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace harness connector.
3.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace wiring harness.
4.REPLACE CRASH ZONE SENSOR
1. Replace crash zone. Refer to SR-24, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-57, "DTC Description".
Is DTC detected?
YES >> GO TO 5.
NO >> INSPECTION END
5.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-57, "DTC Description".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
SRC-58
B0096 B-PILLAR SATELLITE SENSOR
< DTC/CIRCUIT DIAGNOSIS >
B0096 B-PILLAR SATELLITE SENSOR
A
DTC Description INFOID:0000000010431054
POSSIBLE CAUSE G
[B0096–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of satellite sensor RH SRC
• Internal malfunction of air bag diagnosis sensor unit
[B0096–23, B0096–24, B0096–25, B0096–28
• Internal malfunction of satellite sensor RH I
• Internal malfunction of air bag diagnosis sensor unit
[B0096–81, B0096–93]
• Connection malfunction of harness or connector J
• Internal malfunction of satellite sensor RH
• Internal malfunction of air bag diagnosis sensor unit
K
[B0096–86]
• Air bag diagnosis sensor unit and satellite sensor RH is different from the part specified
[B0096–88] L
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of satellite sensor RH
• Internal malfunction of air bag diagnosis sensor unit
M
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE N
1.CHECK SELF-DIAG RESULT
With CONSULT O
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected? P
YES >> Refer to SRC-59, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure INFOID:0000000010431055
WARNING:
SRC-59
B0096 B-PILLAR SATELLITE SENSOR
< DTC/CIRCUIT DIAGNOSIS >
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK DTC
Perform each inspection according to the displayed DTC.
Which DTC is displayed?
[B0096–86] >> GO TO 4.
Other than the above >> GO TO 2.
2.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace harness connector.
3.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace wiring harness.
4.REPLACE SATELLITE SENSOR RH
1. Replace satellite sensor RH. Refer to SR-26, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-59, "DTC Description".
Is DTC detected?
YES >> GO TO 5.
NO >> INSPECTION END
5.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-59, "DTC Description".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
SRC-60
B00D2 FRONT PASSENGER AIR BAG ON INDICATOR
< DTC/CIRCUIT DIAGNOSIS >
B00D2 FRONT PASSENGER AIR BAG ON INDICATOR
A
DTC Description INFOID:0000000010431032
POSSIBLE CAUSE F
[B00D2–04]
• Internal malfunction of front passenger air bag ON indicator
• Internal malfunction of air bag diagnosis sensor unit G
[B00D2–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of front passenger air bag ON indicator SRC
• Internal malfunction of air bag diagnosis sensor unit
[B00D2–12]
• Connection malfunction or short circuit to power supply of harness and connector I
• Internal malfunction of front passenger air bag ON indicator
• Internal malfunction of air bag diagnosis sensor unit
J
[B00D2–13]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of front passenger air bag ON indicator
• Internal malfunction of air bag diagnosis sensor unit K
[B00D2–15]
• Connection malfunction or short circuit to power supply of harness and connector
• Connection malfunction or open circuit of harness and connector L
• Internal malfunction of front passenger air bag ON indicator
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE M
—
DTC CONFIRMATION PROCEDURE N
1.CHECK SELF-DIAG RESULT
With CONSULT
1. Turn ignition switch ON. O
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected?
YES >> Refer to SRC-61, "Diagnosis Procedure". P
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure INFOID:0000000010431033
WARNING:
SRC-61
B00D2 FRONT PASSENGER AIR BAG ON INDICATOR
< DTC/CIRCUIT DIAGNOSIS >
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.CHECK FRONT PASSENGER AIR BAG ON INDICATOR
1. Replace indicator unit. Refer to HAC-126, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-61, "DTC Description".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-61, "DTC Description".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
SRC-62
B00D5 FRONT PASSENGER AIR BAG OFF INDICATOR
< DTC/CIRCUIT DIAGNOSIS >
B00D5 FRONT PASSENGER AIR BAG OFF INDICATOR
A
DTC Description INFOID:0000000010431034
POSSIBLE CAUSE F
[B00D5–04]
• Internal malfunction of front passenger air bag OFF indicator
• Internal malfunction of air bag diagnosis sensor unit G
[B00D5–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of front passenger air bag OFF indicator SRC
• Internal malfunction of air bag diagnosis sensor unit
[B00D5–12]
• Connection malfunction or short circuit to power supply of harness and connector I
• Internal malfunction of front passenger air bag OFF indicator
• Internal malfunction of air bag diagnosis sensor unit
J
[B00D5–13]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of front passenger air bag OFF indicator
• Internal malfunction of air bag diagnosis sensor unit K
[B00D5–15]
• Connection malfunction or short circuit to power supply of harness and connector
• Connection malfunction or open circuit of harness and connector L
• Internal malfunction of front passenger air bag OFF indicator
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE M
—
DTC CONFIRMATION PROCEDURE N
1.CHECK SELF-DIAG RESULT
With CONSULT
1. Turn ignition switch ON. O
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected?
YES >> Refer to SRC-63, "Diagnosis Procedure". P
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure INFOID:0000000010431035
WARNING:
SRC-63
B00D5 FRONT PASSENGER AIR BAG OFF INDICATOR
< DTC/CIRCUIT DIAGNOSIS >
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.CHECK FRONT PASSENGER AIR BAG OFF INDICATOR
1. Replace indicator unit. Refer to HAC-126, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-63, "DTC Description".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-63, "DTC Description".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
SRC-64
B00DF AIR BAG CUTOFF SWITCH
< DTC/CIRCUIT DIAGNOSIS >
B00DF AIR BAG CUTOFF SWITCH
A
DTC Description INFOID:0000000010431036
SRC-65
B00DF AIR BAG CUTOFF SWITCH
< DTC/CIRCUIT DIAGNOSIS >
2. Perform DTC confirmation procedure. Refer to SRC-65, "DTC Description".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
SRC-66
B0099 SATELLITE SENSOR
< DTC/CIRCUIT DIAGNOSIS >
B0099 SATELLITE SENSOR
A
DTC Description INFOID:0000000010377852
POSSIBLE CAUSE G
[B0099–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of other satellite sensor SRC
• Internal malfunction of air bag diagnosis sensor unit
[B0099–23, B0099–24, B0099–25, B0099–28
• Internal malfunction of other satellite sensor I
• Internal malfunction of air bag diagnosis sensor unit
[B0099–81, B0099–93]
• Connection malfunction of harness or connector J
• Internal malfunction of other satellite sensor
• Internal malfunction of air bag diagnosis sensor unit
K
[B0099–86]
• Air bag diagnosis sensor unit and other satellite sensor is different from the part specified
[B0096–88] L
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of other satellite sensor
• Internal malfunction of air bag diagnosis sensor unit
M
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT
N
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
O
Is malfunctioning part detected?
YES >> Refer to SRC-67, "Diagnosis Procedure".
NO >> INSPECTION END
P
Diagnosis Procedure INFOID:0000000010377853
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
SRC-67
B0099 SATELLITE SENSOR
< DTC/CIRCUIT DIAGNOSIS >
1.CHECK DTC
Perform each inspection according to the displayed DTC.
Which DTC is displayed?
[B0099–86] >> GO TO 4.
Other than the above >> GO TO 2.
2.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace harness connector.
3.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace wiring harness.
4.REPLACE OTHER SATELLITE SENSOR
1. Replace other satellite sensor. Refer to SR-26, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-67, "DTC Description".
Is DTC detected?
YES >> GO TO 5.
NO >> INSPECTION END
5.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-67, "DTC Description".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
SRC-68
B1400, B1401, B1402, B1403, B1404, B1405 AIR BAG DIAGNOSIS SENSOR
UNIT
< DTC/CIRCUIT DIAGNOSIS >
B1400, B1401, B1402, B1403, B1404, B1405 AIR BAG DIAGNOSIS SEN-
A
SOR UNIT
DTC Description INFOID:0000000010431056
B
DTC DETECTION LOGIC
POSSIBLE CAUSE
Malfunction in air bag diagnosis sensor unit SRC
FAIL-SAFE
— I
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT J
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
K
Is malfunctioning part detected?
YES >> Refer to SRC-69, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident". L
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure INFOID:0000000010431057
M
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.) N
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector. O
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors. P
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
SRC-69
B1400, B1401, B1402, B1403, B1404, B1405 AIR BAG DIAGNOSIS SENSOR
UNIT
< DTC/CIRCUIT DIAGNOSIS >
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-69, "DTC Description".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
SRC-70
B1406, B1407, B1408, B1409, B1410 AIR BAG DIAGNOSIS SENSOR UNIT
< DTC/CIRCUIT DIAGNOSIS >
B1406, B1407, B1408, B1409, B1410 AIR BAG DIAGNOSIS SENSOR UNIT
A
DTC Description INFOID:0000000010431058
POSSIBLE CAUSE G
Malfunction in air bag diagnosis sensor unit
FAIL-SAFE
— SRC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT I
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT. J
Is malfunctioning part detected?
YES >> Refer to SRC-71, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident". K
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure INFOID:0000000010431059
L
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.) M
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
N
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2. O
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals. P
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-71, "DTC Description".
SRC-71
B1406, B1407, B1408, B1409, B1410 AIR BAG DIAGNOSIS SENSOR UNIT
< DTC/CIRCUIT DIAGNOSIS >
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
SRC-72
B1411, B1412, B1413, B1414, B1415 AIR BAG DIAGNOSIS SENSOR UNIT
< DTC/CIRCUIT DIAGNOSIS >
B1411, B1412, B1413, B1414, B1415 AIR BAG DIAGNOSIS SENSOR UNIT
A
DTC Description INFOID:0000000010431060
POSSIBLE CAUSE
Malfunction in air bag diagnosis sensor unit SRC
FAIL-SAFE
—
I
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT
J
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
K
Is malfunctioning part detected?
YES >> Refer to SRC-73, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END L
M
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device. N
SRC-73
B1411, B1412, B1413, B1414, B1415 AIR BAG DIAGNOSIS SENSOR UNIT
< DTC/CIRCUIT DIAGNOSIS >
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-73, "DTC Description".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
SRC-74
B1416, B1417, B1418, B1419, B1420 AIR BAG DIAGNOSIS SENSOR UNIT
< DTC/CIRCUIT DIAGNOSIS >
B1416, B1417, B1418, B1419, B1420 AIR BAG DIAGNOSIS SENSOR UNIT
A
DTC Description INFOID:0000000010431062
WARNING: M
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
N
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal? O
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS P
SRC-76
B1421 FRONTAL COLLISION DETECTION
< DTC/CIRCUIT DIAGNOSIS >
B1421 FRONTAL COLLISION DETECTION
A
DTC Description INFOID:0000000010431064
POSSIBLE CAUSE D
—
FAIL-SAFE
E
—
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT F
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT. G
Is malfunctioning part detected?
YES >> Refer to SRC-77, "Diagnosis Procedure".
SRC
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure INFOID:0000000010431065
I
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 J
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.PERFORM COLLISION DIAGNOSIS K
Perform collision diagnosis. Refer to SR-7, "FOR FRONTAL COLLISION : When SRS is activated in a colli-
sion" or SR-8, "FOR FRONTAL COLLISION : When SRS is not activated in a collision".
L
>> GO TO 2.
2.FINAL INSPECTION
M
Perform “AIR BAG” Self Diagnostic Result.
Is the inspection result normal?
YES >> INSPECTION END N
NO >> Perform diagnosis of applicable DTC. Refer to SRC-19, "DTC Index".
SRC-77
B1422 SIDE COLLISION DETECTION
< DTC/CIRCUIT DIAGNOSIS >
B1422 SIDE COLLISION DETECTION
DTC Description INFOID:0000000010431066
POSSIBLE CAUSE
—
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected?
YES >> Refer to SRC-78, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure INFOID:0000000010431067
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.PERFORM COLLISION DIAGNOSIS
Perform collision diagnosis. Refer to SR-9, "FOR SIDE AND ROLLOVER COLLISION : When SRS is acti-
vated in a collision" or SR-10, "FOR SIDE AND ROLLOVER COLLISION : When SRS is not activated in a col-
lision".
>> GO TO 2.
2.FINAL INSPECTION
Perform “AIR BAG” Self Diagnostic Result.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Perform diagnosis of applicable DTC. Refer to SRC-19, "DTC Index".
SRC-78
B1425 REAR COLLISION DETECTION
< DTC/CIRCUIT DIAGNOSIS >
B1425 REAR COLLISION DETECTION
A
DTC Description INFOID:0000000010431068
POSSIBLE CAUSE D
—
FAIL-SAFE
E
—
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT F
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT. G
Is malfunctioning part detected?
YES >> Refer to SRC-79, "Diagnosis Procedure".
SRC
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure INFOID:0000000010431069
I
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 J
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.PERFORM COLLISION DIAGNOSIS K
Perform collision diagnosis. Refer to SR-7, "FOR FRONTAL COLLISION : When SRS is activated in a colli-
sion" or SR-8, "FOR FRONTAL COLLISION : When SRS is not activated in a collision".
L
>> GO TO 2.
2.FINAL INSPECTION
M
Perform “AIR BAG” Self Diagnostic Result.
Is the inspection result normal?
YES >> INSPECTION END N
NO >> Perform diagnosis of applicable DTC. Refer to SRC-19, "DTC Index".
SRC-79
B1427 CONFIG SETTING
< DTC/CIRCUIT DIAGNOSIS >
B1427 CONFIG SETTING
DTC Description INFOID:0000000010431978
POSSIBLE CAUSE
[B1427–55]
Mistake of configuration for air bag diagnosis sensor unit
[B1427–55]
Incomplete of configuration for air bag diagnosis sensor unit
FAIL-SAFE
—
Diagnosis Procedure INFOID:0000000010431979
1.PERFORM CONFIGURATION
Perform configuration for air bag diagnosis sensor unit.
SRC-80
B142A IGN VOLTAGE
< DTC/CIRCUIT DIAGNOSIS >
B142A IGN VOLTAGE
A
DTC Description INFOID:0000000010431070
POSSIBLE CAUSE
E
[B142A–16]
• Malfunction of battery voltage (less than 9 V)
• Connection malfunction of harness or connector
• Internal malfunction of air bag diagnosis sensor unit F
[B142A–17]
• Malfunction of battery voltage (more than 16 V)
G
• Connection malfunction of harness or connector
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE SRC
—
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT I
With CONSULT
1. Turn ignition switch ON. J
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected?
YES >> Refer to SRC-81, "Diagnosis Procedure". K
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure INFOID:0000000010431071 L
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3 M
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK BATTERY VOLTAGE N
Check battery voltage. Refer to PG-136, "FOR MAINTENANCE REQUIRED BATTERY MODELS : How to
Handle Battery" (For maintenance required battery) or PG-142, "FOR MAINTENANCE FREE BATTERY
MODELS : How to Handle Battery" (For maintenance free battery). O
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace battery. Refer to PG-155, "Removal and Installation". P
2.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace harness connectors.
SRC-81
B142A IGN VOLTAGE
< DTC/CIRCUIT DIAGNOSIS >
3.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace wiring harness.
4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-81, "DTC Description".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
SRC-82
B1430 SEAT BELT PRE-TENSIONER
< DTC/CIRCUIT DIAGNOSIS >
B1430 SEAT BELT PRE-TENSIONER
A
DTC Description INFOID:0000000010431072
[B1430–09, B1430–1A]
• Connection malfunction or short circuit of harness and connector
• Internal malfunction of seat belt pre-tensioner LH I
• Internal malfunction of air bag diagnosis sensor unit
[B1430–11] J
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of seat belt pre-tensioner LH
• Internal malfunction of air bag diagnosis sensor unit
K
[B1430–12]
• Connection malfunction or short circuit to power supply of harness and connector
• Internal malfunction of seat belt pre-tensioner LH
• Internal malfunction of air bag diagnosis sensor unit L
[B1430–13]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of seat belt pre-tensioner LH M
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE N
—
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT O
With CONSULT
1. Turn ignition switch ON.
P
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected?
YES >> Refer to SRC-84, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
SRC-83
B1430 SEAT BELT PRE-TENSIONER
< DTC/CIRCUIT DIAGNOSIS >
Diagnosis Procedure INFOID:0000000010431073
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE SEAT BELT PRE-TENSIONER LH
1. Replace seat belt pre-tensioner LH. Refer to SB-7, "SEAT BELT RETRACTOR : Removal and Installa-
tion".
2. Perform DTC confirmation procedure. Refer to SRC-83, "DTC Description".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-83, "DTC Description".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
SRC-84
B1431 SEAT BELT PRE-TENSIONER
< DTC/CIRCUIT DIAGNOSIS >
B1431 SEAT BELT PRE-TENSIONER
A
DTC Description INFOID:0000000010431074
[B1431–09, B1431–1A]
• Connection malfunction or short circuit of harness and connector
• Internal malfunction of seat belt pre-tensioner RH I
• Internal malfunction of air bag diagnosis sensor unit
[B1431–11] J
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of seat belt pre-tensioner RH
• Internal malfunction of air bag diagnosis sensor unit
K
[B1431–12]
• Connection malfunction or short circuit to power supply of harness and connector
• Internal malfunction of seat belt pre-tensioner RH
• Internal malfunction of air bag diagnosis sensor unit L
[B1431–13]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of seat belt pre-tensioner RH M
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE N
—
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT O
With CONSULT
1. Turn ignition switch ON.
P
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected?
YES >> Refer to SRC-86, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
SRC-85
B1431 SEAT BELT PRE-TENSIONER
< DTC/CIRCUIT DIAGNOSIS >
Diagnosis Procedure INFOID:0000000010431075
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE SEAT BELT PRE-TENSIONER RH
1. Replace seat belt pre-tensioner RH. Refer to SB-7, "SEAT BELT RETRACTOR : Removal and Installa-
tion".
2. Perform DTC confirmation procedure. Refer to SRC-85, "DTC Description".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-85, "DTC Description".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
SRC-86
B1432 LAP PRE-TENSIONER
< DTC/CIRCUIT DIAGNOSIS >
B1432 LAP PRE-TENSIONER
A
DTC Description INFOID:0000000010431076
B
CONSULT screen items
DTC DTC detecting condition
(Trouble diagnosis content)
PRE-TEN FRONT LH 2
C
B1432–09 [front lap seat belt pre-tensioner squib left Lap pre-tensioner LH circuits are shorted to each other
hand component failures (cross connection)]
PRE-TEN FRONT LH 2
B1432–11 (front lap seat belt pre-tensioner squib left Lap pre-tensioner LH circuit is shorted to ground D
hand circuit short to GND)
PRE-TEN FRONT LH 2
B1432–12 (front lap seat belt pre-tensioner squib left Lap pre-tensioner LH circuit is shorted to power supply circuit E
hand circuit short to battery)
PRE-TEN FRONT LH 2
B1432–13 (front lap seat belt pre-tensioner squib left Lap pre-tensioner LH circuit is open
F
hand circuit)
PRE-TEN FRONT LH 2
B1432–1A (front lap seat belt pre-tensioner squib left Lap pre-tensioner LH circuits are shorted to each other
hand circuit resistance below threshold) G
POSSIBLE CAUSE
[B1432–09, B1432–30]
SRC
• Connection malfunction or short circuit of harness and connector
• Internal malfunction of lap pre-tensioner LH
• Internal malfunction of air bag diagnosis sensor unit I
[B1432–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of lap pre-tensioner LH J
• Internal malfunction of air bag diagnosis sensor unit
[B1432–12]
• Connection malfunction or short circuit to power supply of harness and connector K
• Internal malfunction of lap pre-tensioner LH
• Internal malfunction of air bag diagnosis sensor unit
L
[B1432–13]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of lap pre-tensioner LH
• Internal malfunction of air bag diagnosis sensor unit M
FAIL-SAFE
—
N
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAGNOSTIC RESULT
O
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected? P
YES >> Refer to SRC-87, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure INFOID:0000000010431077
WARNING:
SRC-87
B1432 LAP PRE-TENSIONER
< DTC/CIRCUIT DIAGNOSIS >
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE LAP PRE-TENSIONER LH
1. Replace lap pre-tensioner LH. Refer to SB-7, "SEAT BELT RETRACTOR : Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-87, "DTC Description".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-87, "DTC Description".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
SRC-88
B1433 LAP PRE-TENSIONER
< DTC/CIRCUIT DIAGNOSIS >
B1433 LAP PRE-TENSIONER
A
DTC Description INFOID:0000000010431078
B
CONSULT screen items
DTC DTC detecting condition
(Trouble diagnosis content)
PRE-TEN FRONT RH 2
C
B1433–09 [front lap seat belt pre-tensioner squib right Lap pre-tensioner RH circuits are shorted to each other
hand component failures (cross connection)]
PRE-TEN FRONT RH 2
B1433–11 (front lap seat belt pre-tensioner squib right Lap pre-tensioner RH circuit is shorted to ground D
hand circuit short to GND)
PRE-TEN FRONT RH 2
B1433–12 (front lap seat belt pre-tensioner squib right Lap pre-tensioner RH circuit is shorted to power supply circuit E
hand circuit short to battery)
PRE-TEN FRONT RH 2
B1433–13 (front lap seat belt pre-tensioner squib right Lap pre-tensioner RH circuit is open
F
hand circuit)
PRE-TEN FRONT RH 2
B1433–1A (front lap seat belt pre-tensioner squib right Lap pre-tensioner RH circuits are shorted to each other
hand circuit resistance below threshold) G
POSSIBLE CAUSE
[B1433–09, B1433–1A]
SRC
• Connection malfunction or short circuit of harness and connector
• Internal malfunction of lap pre-tensioner RH
• Internal malfunction of air bag diagnosis sensor unit I
[B1433–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of lap pre-tensioner RH J
• Internal malfunction of air bag diagnosis sensor unit
[B1433–12]
• Connection malfunction or short circuit to power supply of harness and connector K
• Internal malfunction of lap pre-tensioner RH
• Internal malfunction of air bag diagnosis sensor unit
L
[B1433–13]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of lap pre-tensioner RH
• Internal malfunction of air bag diagnosis sensor unit M
FAIL-SAFE
—
N
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAGNOSTIC RESULT
O
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Is malfunctioning part detected? P
YES >> Refer to SRC-89, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure INFOID:0000000010431079
WARNING:
SRC-89
B1433 LAP PRE-TENSIONER
< DTC/CIRCUIT DIAGNOSIS >
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connector.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE LAP PRE-TENSIONER RH
1. Replace lap pre-tensioner RH. Refer to SB-7, "SEAT BELT RETRACTOR : Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-89, "DTC Description".
Is DTC detected?
YES >> GO TO 4.
NO >> INSPECTION END
4.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Perform DTC confirmation procedure. Refer to SRC-89, "DTC Description".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END
SRC-90
SRS AIR BAG WARNING LAMP DOES NOT TURN OFF
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS A
SRS AIR BAG WARNING LAMP DOES NOT TURN OFF
Diagnosis Procedure INFOID:0000000010377880
B
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Check air bag warning lamp operation.
J
Is the inspection result normal?
YES >> INSPECTION END
NO >> GO TO 5.
K
5.REPLACE COMBINATION METER
1. Replace combination meter. Refer to MWI-80, "Removal and Installation".
2. Check air bag warning lamp operation. L
Is the inspection result normal?
YES >> INSPECTION END
NO >> Check intermittent incident. Refer to GI-41, "Intermittent Incident". M
SRC-91
SRS AIR BAG WARNING LAMP DOES NOT TURN ON
< SYMPTOM DIAGNOSIS >
SRS AIR BAG WARNING LAMP DOES NOT TURN ON
Diagnosis Procedure INFOID:0000000010377881
1.CHECK DTC WITH AIR BAG DIAGNOSIS SENSOR UNIT AND COMBINATION METER
Check that DTC is not detected with air bag diagnosis sensor unit and combination meter.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Refer to SRC-19, "DTC Index" (air bag diagnosis sensor unit) and MWI-39, "DTC Index" (combi-
nation meter).
2.CHECK COMBINATION METER POWER SUPPLY AND GROUND CIRCUIT
Check combination meter unit power supply and ground circuit. Refer to MWI-61, "COMBINATION METER :
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning parts.
3.CHECK AIR BAG FUSE
Check 10 A fuse [No. 2, located in fuse block (J/B)].
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace the fuse.
4.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Replace harness connectors.
5.CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Replace wiring harness.
6.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-28, "Removal and Installation".
2. Check air bag warning lamp operation.
Is the inspection result normal?
YES >> INSPECTION END
NO >> GO TO 7.
7.REPLACE COMBINATION METER
1. Replace combination meter. Refer to MWI-80, "Removal and Installation".
2. Check air bag warning lamp operation.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Check intermittent incident. Refer to GI-41, "Intermittent Incident".
SRC-92