SRC32
SRC32
SRC32
SRC
A
B
SECTION
SRS AIRBAG CONTROL SYSTEM C
E
CONTENTS
BASIC INSPECTION .................................... 3 Description ...............................................................17 F
DTC Logic ................................................................17
DIAGNOSIS AND REPAIR WORK FLOW ......... 3 Diagnosis Procedure (Component Diagnosis) ........18
Work Flow ................................................................. 3 G
B1065 – B1068, B1070 – B1073 PASSEN-
INTERMITTENTS INCIDENT .............................. 5 GER AIRBAG MODULE ................................... 20
Inspection Procedure ............................................... 5 Description ...............................................................20
Trouble Diagnosis with CONSULT-III ....................... 5 DTC Logic ................................................................20 SRC
Diagnosis Procedure (Component Diagnosis) ........21
FUNCTION DIAGNOSIS ............................... 6
B1134 – B1137 SIDE AIRBAG MODULE LH ... 23 I
SRS AIR BAG SYSTEM ...................................... 6 Description ...............................................................23
SRS Configuration .................................................... 6 DTC Logic ................................................................23
SRS Component Parts Location ............................... 7 Diagnosis Procedure (Component Diagnosis) ........24
Driver Air Bag Module ............................................... 7 J
Front Passenger Air Bag Module .............................. 8 B1129 – B1132 SIDE AIRBAG MODULE RH ... 26
Front Side Air Bag ..................................................... 8 Description ...............................................................26
Side Curtain Air Bag .................................................. 8 DTC Logic ................................................................26 K
Front Seat Belt Pre-tensioner with Load Limiter ...... 8 Diagnosis Procedure (Component Diagnosis) ........27
Direct-connect SRS Component Connectors ............ 9
B1198 – B1201 SIDE CURTAIN AIR BAG
OCCUPANT CLASSIFICATION SYSTEM .........10 L
MODULE LH (FRONT) ...................................... 29
System Diagram ...................................................... 10 Description ...............................................................29
Occupant Classification System (OCS) .................. 10 DTC Logic ................................................................29
Diagnosis Procedure (Component Diagnosis) ........30 M
PASSENGER SEAT BELT WARNING SYS-
TEM ....................................................................12 B1193 – B1196 SIDE CURTAIN AIR BAG
System Diagram ...................................................... 12 MODULE RH (FRONT) ..................................... 32 N
System Description ................................................. 12 Description ...............................................................32
Component Parts Location ...................................... 12 DTC Logic ................................................................32
Diagnosis Procedure (Component Diagnosis) ........33
ON BOARD DIAGNOSTIC (OBD) SYSTEM ......13 O
Trouble Diagnosis Introduction ............................... 13 B1150 – B1153 SIDE CURTAIN AIR BAG
SRS Operation Check ............................................. 13 MODULE LH (REAR) ........................................ 35
Trouble Diagnosis without CONSULT-III ................ 15 Description ...............................................................35 P
CONSULT-III Function (AIR BAG) .......................... 15 DTC Logic ................................................................35
Self-Diagnosis Function (Without CONSULT-III) .... 15 Diagnosis Procedure (Component Diagnosis) ........36
COMPONENT DIAGNOSIS ......................... 17 B1145 – B1148 SIDE CURTAIN AIR BAG
MODULE RH (REAR) ....................................... 38
B1049 – B1052, B1054 – B1057 DRIVER AIR-
Description ...............................................................38
BAG MODULE ...................................................17 DTC Logic ................................................................38
OVERALL SEQUENCE
C
SRC
M
WHIA0348E
*1 SRC-13, "Trouble Diagnosis Intro- *2 SRC-13, "SRS Operation Check" *3 SRC-5, "Trouble Diagnosis with N
duction" CONSULT-III"
*4 SRC-15, "Self-Diagnosis Function
(Without CONSULT-III)"
O
DETAILED WORK FLOW
1.CUSTOMER INFORMATION
P
Get detailed information from the customer about the symptom.
>> GO TO 2
2.PRELIMINARY CHECK
Perform preliminary check. Refer to SRC-13, "Trouble Diagnosis Introduction".
>> GO TO 4
4.USER MODE
Perform self-diagnosis using the "AIR BAG" warning lamp in User mode. Refer to SRC-13, "SRS Operation
Check".
>> GO TO 5
5.SELF-DIAGNOSIS
Perform SELF-DIAGNOSIS. Refer to SRC-5, "Trouble Diagnosis with CONSULT-III" (w/CONSULT-III) or
SRC-15, "Self-Diagnosis Function (Without CONSULT-III)" (w/o CONSULT- III).
>> GO TO 6
6.REPLACE PART
Replace the malfunctioning part.
>> GO TO 7
7.FINAL CHECK
Check SRS using Diagnosis mode and User mode.
Does Diagnosis mode and User mode indicate SRS normal?
YES >> Inspection end.
NO >> GO TO 5
INTERMITTENT TROUBLE B
An intermittent incident may have occured in the past but is not being detected currently. This DTC will not be
detected on SELF DIAG [CURRENT], but may be viewed on SELF DIAG [PAST] using CONSULT-III.
Trouble Diagnosis with CONSULT-III INFOID:0000000001735284
C
DIAGNOSTIC PROCEDURE 4
D
Check SRS Repair History
1.CONSIDER POSSIBILITY THAT SELF-DIAGNOSTIC RESULT WAS NOT ERASED AFTER REPAIR
E
Check repair history of the SRS.
Have any previous repairs been made to the SRS?
Yes >> Self-diagnostic result “SELF-DIAG [PAST]” (previously stored in the memory) might not be erased
F
after repair. Go to "DIAGNOSTIC PROCEDURE 3". Refer to SRC-15, "Self-Diagnosis Function
(Without CONSULT-III)".
No >> Go to "DIAGNOSTIC PROCEDURE 2". Refer to SRC-13, "SRS Operation Check".
G
SRC
WHIA0215E
The air bag deploys if the air bag diagnosis sensor unit is activated while the ignition switch is in the ON or
START position.
The collision modes for which supplemental restraint systems are activated are different among the SRS sys-
tems. For example, the driver air bag module, front passenger air bag module, front seat belt pre-tensioners
and seat belt buckle pre-tensioner assemblies are activated in a frontal collision but not in a side collision.
SRS configurations for some collision modes are as follows:
SRC
WHIA0216E
I
1. Side curtain air bag modules 2. Front RH side air bag module 3. Belt tension sensor
4. RH side air bag (satellite) sensor 5. Front RH seat belt pre-tension- 6. Seat belt buckle pre-tensioner assembly
er RH J
7. Occupant classification system sen- 8. Occupant classification system 9. Front passenger air bag off indicator
sor control unit
10. Front passenger air bag module 11. Crash zone sensor 12. Air bag warning lamp
K
13. Spiral cable 14. Driver air bag module 15. LH side air bag (satellite) sensor
16. Front LH seat belt pre-tensioner 17. Air bag diagnosis sensor unit 18. Front LH side air bag module
L
Driver Air Bag Module INFOID:0000000001735287
The driver air bag module is dual stage and located in the steering
wheel assembly. It operates with the SRS system in a frontal colli- M
sion exceeding a specified level.
WHIA0325E
The front passenger air bag module is located behind the instrument
panel assembly. It operates with the SRS system in a frontal colli-
sion exceeding a specified level. Refer to SRC-10, "Occupant Clas-
sification System (OCS)" for more information.
WHIA0332E
Front side air bag modules are built into the front seatback assem-
blies. Vehicles with side air bags are equipped with labels as shown.
WHIA0327E
Side curtain air bag modules are located above the vehicle headlining.
Vehicles with side curtain air bags are equipped with labels as
shown.
WHIA0041E
The seat belt pre-tensioner system with load limiter is installed for
both the driver's seat and the front passenger's seat. It operates
simultaneously with the SRS air bag system in the event of a frontal
collision with an impact exceeding a specified level.
When the frontal collision with an impact exceeding a specified level
occurs, seat belt slack resulting from clothing or other factors is
immediately taken up by the pre-tensioner. Vehicle passengers are
securely restrained.
When passengers in a vehicle are thrown forward in a collision and
the restraining force of the seat belt exceeds a specified level, the
load limiter permits the specified extension of the seat belt by the
WHIA0324E
twisting of the ELR shaft, and a relaxation of the chest-area seat belt
web tension while maintaining force.
A
The following SRS components use direct-connect style harness connectors.
• Driver air bag module
• Front passenger air bag module B
• LH side front curtain air bag module
• LH side rear curtain air bag module
• RH side front curtain air bag module
• RH side rear curtain air bag module C
• Front LH seat belt pre-tensioner
• Front RH seat belt pre-tensioner
• Seat belt buckle pre-tensioner assembly LH D
• Seat belt buckle pre-tensioner assembly RH
Always pull up to release locking tab prior to removing connector from SRS component.
Always push down to lock black locking tab after installing connector
to SRS component. When locked, the black locking tab is level with E
the connector housing.
WHIA0103E
SRC
ALHIA0042GB
The occupant classification system (OCS) identifies different size occupants, out of position occupants, and
detects if child seat is present in the front passenger seat. The OCS receives inputs from the occupant classi-
fication sensor (located inside the passenger seat cushion assembly) and belt tension sensor (part of the pas-
senger front seat belt assembly and located at the belt anchor location). Depending on classification of the
passenger, the OCS sends a signal to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit
uses this signal and the seat belt buckle switch RH signal to determine deployment or non deployment of the
passenger front air bag in the event of a collision. Depending on the signals received, the air bag diagnosis
sensor unit can disable the passenger front air bag completely.
NOTE:
In case of customer concern, CONSULT-III can be used to confirm the passenger air bag status (readiness).
Passenger Air Bag Status Conditions
Front Passenger Seat PASS AIR BAG OFF Indicator Passenger Air Bag Status
CONSULT-III Display
(Condition) (Status) (Readiness)
Seat occupied OFF Active (enabled) ON
WHIA0187E
SRC
ALHIA0028GB
The passenger seat belt warning system will remind the driver if the
driver or front passenger seat belt should be buckled by turning on
the seat belt warning light (1). The system works in conjunction with
the occupant classification system. Refer to SRC-10, "Occupant
Classification System (OCS)".
AWHIA0032ZZ
CAUTION: B
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to do so in
this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harness con-
nectors.
• Do not attempt to repair, splice or modify SRS wiring harnesses. If a harness is damaged, replace it C
with a new one.
• Keep ground connections clean.
DIAGNOSIS FUNCTION D
The SRS self-diagnosis results can be read by using “AIR BAG” warning lamp and/or CONSULT-III.
The User mode is exclusively prepared for the customer (driver). This mode warns the driver of a system mal-
function through the operation of the “AIR BAG” warning lamp. E
The Diagnosis mode allows the technician to locate and inspect the malfunctioning part.
The mode applications for the “AIR BAG” warning lamp and CONSULT-III are as follows:
F
User mode Diagnosis mode Display type
“AIR BAG” warning lamp X X ON-OFF operation
CONSULT-III — X Monitoring G
HOW TO PERFORM TROUBLE DIAGNOSES FOR QUICK AND ACCURATE REPAIR
A good understanding of the malfunction conditions can make troubleshooting faster and more accurate.
In general, each customer feels differently about a malfunction. It is important to fully understand the symp- SRC
toms or conditions for a customer complaint.
Information From Customer
WHAT - Vehicle model I
WHEN - Date, Frequencies
WHERE - Road conditions
HOW - Operating conditions, Symptoms J
Preliminary Check
Check that the following parts are in good order.
• Battery K
• Fuse
• System component-to-harness connections
SRS Operation Check INFOID:0000000001735299
L
DIAGNOSTIC PROCEDURE 1
M
Checking SRS Operation Using “AIR BAG” Warning Lamp—User Mode
1. Turn the ignition switch from OFF to ON, and check that the air bag warning lamp blinks.
2. Compare the SRS air bag warning lamp blinking pattern with the N
examples.
BF-1845D
• No malfunction is detected.
—
• No further action is necessary.
SHIA0011E
Go to DIAGNOSTIC PROCEDURE
2 that follows (with CONSULT-III) or
The system is malfunctioning and
SRC-15, "Trouble Diagnosis without
needs to be repaired as indicated.
CONSULT-III" (without CONSULT-
III).
SHIA0012E
SHIA0014E
DIAGNOSTIC PROCEDURE 2
1. Connect CONSULT-III.
2. Diagnostic code is displayed on "SELF-DIAG [CURRENT]".
If no malfunction is detected on "SELF-DIAG [CURRENT]", but malfunction is detected in "SRS Operation
Check" using the "AIR BAG" warning lamp, the following cases may exist:
• "SELF-DIAG [PAST]" memory might not be erased.
• The SRS system malfunctions intermittently.
Perform DIAGNOSTIC PROCEDURE 4. Refer to SRC-15, "Self-Diagnosis Function (Without CONSULT-
III)".
A
DIAGNOSTIC PROCEDURE 6
Inspect SRS Malfunction Using "AIR BAG" Warning Lamp—Diagnosis Mode
B
NOTE:
SRS will not enter Diagnosis mode if no malfunction is detected in User mode.
1. Turn ignition switch ON.
C
2. After “AIR BAG” warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
3. Wait more than 3 seconds.
4. Repeat steps 1 to 3 two more times (3 times total). D
5. Turn ignition switch ON.
SRS is now in Diagnosis mode. Refer to SRC-85, "Trouble Diagnosis without CONSULT-III".
E
CONSULT-III Function (AIR BAG) INFOID:0000000001735301
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
F
AIR BAG diagnostic mode Description
A current Self-diagnosis result (also indicated by the number of warning lamp flashes in the Diagnosis
SELF-DIAG [CURRENT] mode) is displayed on the CONSULT-III screen in real time. This refers to a malfunctioning part requir- G
ing repairs.
Diagnosis results previously stored in the memory are displayed on the CONSULT-III screen. The
SELF-DIAG [PAST]
stored results will remain until memory erasing is executed. SRC
With TROUBLE DIAG RECORD, diagnosis results previously erased by a reset operation can be dis-
TROUBLE DIAG RECORD
played on the CONSULT-III screen.
Air bag diagnosis sensor unit ECU discriminated number (identification number) is displayed. Air bag I
ECU DISCRIMINATED NO. diagnosis sensor unit has individual ECU discriminated number (identification number) based on model
and equipment.
The STATUS (readiness) of the front passenger air bag module is displayed. The STATUS displayed
(ON/OFF) depends on the signals supplied to the occupant classification system control module and
J
PASSENGER AIR BAG
air bag diagnosis sensor unit. Refer to SRC-10, "Occupant Classification System (OCS)" for more in-
formation.
K
Self-Diagnosis Function (Without CONSULT-III) INFOID:0000000001735302
• The reading of these results is accomplished using one of two modes — “User mode” and “Diagnosis
mode”. L
• After a malfunction is repaired, turn the ignition switch OFF for at least one second, then back ON. Diagnosis
mode returns to the User mode. At that time, the self-diagnostic result is cleared.
M
SHIA0183E
DIAGNOSTIC PROCEDURE 3
Final Check of SRS Using CONSULT-III—Diagnosis Mode
1. Connect CONSULT-III.
2. If no DTC is detected on “SELF-DIAG [CURRENT]”, repair of SRS is completed. Go to step 3.
If any DTC is detected on “SELF-DIAG [CURRENT]”, the malfunctioning part has not been repaired com-
pletely or another malfunctioning part is being detected. Perform DIAGNOSTIC PROCEDURE 2. Refer to
SRC-13, "SRS Operation Check".
3. Touch “ERASE”.
NOTE:
Touch “ERASE” to clear the memory of the malfunction (“SELF-DIAG [PAST]”).
If the memory of the malfunction in “SELF-DIAG [PAST]” is not erased, the User mode shows the system
malfunction by the operation of the warning lamp even if the malfunction is repaired completely.
4. Touch “BACK” key of CONSULT-III. Touch “SELF-DIAG [PAST]”.
5. Check that no malfunction is detected on “SELF-DIAG [PAST]”.
6. Touch “BACK” key of CONSULT-III to return to User mode from Diagnosis mode.
7. Turn ignition switch OFF and then turn off and disconnect CONSULT-III.
8. Go to SRC-13, "SRS Operation Check".
DIAGNOSTIC PROCEDURE 4
Check SRS Repair History
1.CONSIDER POSSIBILITY THAT SELF-DIAGNOSTIC RESULT WAS NOT ERASED AFTER REPAIR
Check repair history of the SRS.
Have any previous repairs been made to the SRS?
Yes >> Self-diagnostic result “SELF-DIAG [PAST]” (previously stored in the memory) might not be erased
after repair. Perform DIAGNOSTIC PROCEDURE 3. Refer to SRC-15, "Self-Diagnosis Function
(Without CONSULT-III)".
No >> Perform DIAGNOSTIC PROCEDURE 2. Refer to SRC-13, "SRS Operation Check".
WHIA0260E
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check for the DTC on CONSULT-lll.
Is the DTC detected?
YES >> Refer to SRC-18, "Diagnosis Procedure (Component Diagnosis)".
NO >> Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2
2.IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3
3.WAIT TIME
Wait more than 3 seconds.
>> GO TO 4
4.REPEAT STEPS
Repeat steps 1 to 3 twice.
>> GO TO 5.
5.IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 6.
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-85, "Trouble Diag-
nosis without CONSULT-III".
>> END
Diagnosis Procedure (Component Diagnosis) INFOID:0000000001735305
>> GO TO 4 D
4.SPIRAL CABLE
Replace the spiral cable. Refer to SR-7, "Removal and Installation".
E
>> GO TO 5
5.AIR BAG DIAGNOSIS SENSOR UNIT F
Replace the air bag diagnosis sensor unit. Refer to SR-17, "Removal and Installation".
>> GO TO 6 G
6.RELATED HARNESS
Replace the related harness. SRC
>> END
I
PART LOCATION
Refer to SRC-7, "SRS Component Parts Location".
DTC Logic INFOID:0000000001735307
Without CONSULT-lll
WHIA0261E
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check for the DTC on CONSULT-lll.
Revision: March 2010 SRC-20 2008 QX56
B1065 – B1068, B1070 – B1073 PASSENGER AIRBAG MODULE
< COMPONENT DIAGNOSIS >
Is the DTC detected?
YES >> Refer to SRC-21, "Diagnosis Procedure (Component Diagnosis)". A
NO >> Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE: B
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.IGNITION SWITCH C
Turn ignition switch ON.
>> GO TO 2 D
2.IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second. E
>> GO TO 3
3.WAIT TIME F
Wait more than 3 seconds.
G
>> GO TO 4
4.REPEAT STEPS
Repeat steps 1 to 3 twice. SRC
>> GO TO 5
I
5.IGNITION SWITCH
Turn ignition switch ON.
J
>> GO TO 6
6.DIAGNOSTIC MODE K
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-85, "Trouble Diag-
nosis without CONSULT-III".
L
>> END
Diagnosis Procedure (Component Diagnosis) INFOID:0000000001735308
M
Recheck SRS after each replacement.
1.HARNESS CONNECTOR
N
Is there any visible damage to the connector?
YES or NO
YES >> Replace the harness. O
NO >> GO TO 2
2.WIRING HARNESS
Is there any visible damage to the harness? P
YES or NO
YES >> Replace the harness.
NO >> GO TO 3
3.FRONT PASSENGER AIR BAG MODULE
Replace the front passenger air bag module. Refer to SR-10, "Removal and Installation".
>> GO TO 4
4.AIR BAG DIAGNOSIS SENSOR UNIT
Replace the air bag diagnosis sensor unit. Refer to SR-17, "Removal and Installation".
>> GO TO 5
5.RELATED HARNESS
Replace the related harness.
>> END
I
Without CONSULT-lll
WHIA0265E
1.INSPECTION START
Turn ignition switch ON. N
>> GO TO 2.
2.CHECK SELF-DIAG RESULT O
>> GO TO 2
2.IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3
3.WAIT TIME
Wait more than 3 seconds.
>> GO TO 4
4.REPEAT STEPS
Repeat steps 1 to 3 twice.
>> GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 6
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-85, "Trouble Diag-
nosis without CONSULT-III".
>> END
Diagnosis Procedure (Component Diagnosis) INFOID:0000000001735311
>> GO TO 4
4.AIR BAG DIAGNOSIS SENSOR UNIT
Replace the air bag diagnosis sensor unit. Refer to SR-17, "Removal and Installation".
>> GO TO 5
5.RELATED HARNESS
Revision: March 2010 SRC-24 2008 QX56
B1134 – B1137 SIDE AIRBAG MODULE LH
< COMPONENT DIAGNOSIS >
Replace the related harness.
A
>> END
SRC
PART LOCATION
Refer to SRC-7, "SRS Component Parts Location".
DTC Logic INFOID:0000000001735313
Without CONSULT-lll
WHIA0264E
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check for the DTC on CONSULT-lll.
Is the DTC detected?
YES >> Refer to SRC-27, "Diagnosis Procedure (Component Diagnosis)".
NO >> Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.IGNITION SWITCH
Revision: March 2010 SRC-26 2008 QX56
B1129 – B1132 SIDE AIRBAG MODULE RH
< COMPONENT DIAGNOSIS >
Turn ignition switch ON.
A
>> GO TO 2
2.IGNITION SWITCH B
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3 C
3.WAIT TIME
Wait more than 3 seconds. D
>> GO TO 4
4.REPEAT STEPS E
Repeat steps 1 to 3 twice.
F
>> GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON. G
>> GO TO 6
SRC
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-85, "Trouble Diag-
nosis without CONSULT-III". I
>> END
J
Diagnosis Procedure (Component Diagnosis) INFOID:0000000001735314
>> GO TO 4 P
>> GO TO 5
5.RELATED HARNESS
Revision: March 2010 SRC-27 2008 QX56
B1129 – B1132 SIDE AIRBAG MODULE RH
< COMPONENT DIAGNOSIS >
Replace the related harness.
>> END
I
Without CONSULT-lll
WHIA0255E
1.INSPECTION START
Turn ignition switch ON. N
>> GO TO 2.
2.CHECK SELF-DIAG RESULT O
>> GO TO 2
2.IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3
3.WAIT TIME
Wait more than 3 seconds.
>> GO TO 4
4.REPEAT STEPS
Repeat steps 1 to 3 twice.
>> GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 6
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-85, "Trouble Diag-
nosis without CONSULT-III".
>> END
Diagnosis Procedure (Component Diagnosis) INFOID:0000000001735317
>> GO TO 4
4.AIR BAG DIAGNOSIS SENSOR UNIT
Replace the air bag diagnosis sensor unit. SR-17, "Removal and Installation".
>> GO TO 5
5.RELATED HARNESS
Revision: March 2010 SRC-30 2008 QX56
B1198 – B1201 SIDE CURTAIN AIR BAG MODULE LH (FRONT)
< COMPONENT DIAGNOSIS >
Replace the related harness.
A
>> END
SRC
PART LOCATION
Refer to SRC-7, "SRS Component Parts Location".
DTC Logic INFOID:0000000001735319
Without CONSULT-lll
WHIA0253E
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check for the DTC on CONSULT-lll.
Is the DTC detected?
YES >> Refer to SRC-33, "Diagnosis Procedure (Component Diagnosis)".
NO >> Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.IGNITION SWITCH
Revision: March 2010 SRC-32 2008 QX56
B1193 – B1196 SIDE CURTAIN AIR BAG MODULE RH (FRONT)
< COMPONENT DIAGNOSIS >
Turn ignition switch ON.
A
>> GO TO 2
2.IGNITION SWITCH B
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3 C
3.WAIT TIME
Wait more than 3 seconds. D
>> GO TO 4
4.REPEAT STEPS E
Repeat steps 1 to 3 twice.
F
>> GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON. G
>> GO TO 6
SRC
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-85, "Trouble Diag-
nosis without CONSULT-III". I
>> END
J
Diagnosis Procedure (Component Diagnosis) INFOID:0000000001735320
>> GO TO 4 P
>> GO TO 5
5.RELATED HARNESS
Revision: March 2010 SRC-33 2008 QX56
B1193 – B1196 SIDE CURTAIN AIR BAG MODULE RH (FRONT)
< COMPONENT DIAGNOSIS >
Replace the related harness.
>> END
I
Without CONSULT-lll
WHIA0254E
1.INSPECTION START
Turn ignition switch ON. N
>> GO TO 2.
2.CHECK SELF-DIAG RESULT O
>> GO TO 2
2.IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3
3.WAIT TIME
Wait more than 3 seconds.
>> GO TO 4
4.REPEAT STEPS
Repeat steps 1 to 3 twice.
>> GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 6
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-85, "Trouble Diag-
nosis without CONSULT-III".
>> END
Diagnosis Procedure (Component Diagnosis) INFOID:0000000001735323
>> GO TO 4
4.AIR BAG DIAGNOSIS SENSOR UNIT
Replace the air bag diagnosis sensor unit. Refer to SR-17, "Removal and Installation".
>> GO TO 5
5.RELATED HARNESS
Revision: March 2010 SRC-36 2008 QX56
B1150 – B1153 SIDE CURTAIN AIR BAG MODULE LH (REAR)
< COMPONENT DIAGNOSIS >
Replace the related harness.
A
>> END
SRC
PART LOCATION
Refer to SRC-7, "SRS Component Parts Location".
DTC Logic INFOID:0000000001735325
Without CONSULT-lll
WHIA0252E
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check for the DTC on CONSULT-lll.
Is the DTC detected?
YES >> Refer to SRC-39, "Diagnosis Procedure (Component Diagnosis)".
NO >> Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.IGNITION SWITCH
Revision: March 2010 SRC-38 2008 QX56
B1145 – B1148 SIDE CURTAIN AIR BAG MODULE RH (REAR)
< COMPONENT DIAGNOSIS >
Turn ignition switch ON.
A
>> GO TO 2
2.IGNITION SWITCH B
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3 C
3.WAIT TIME
Wait more than 3 seconds. D
>> GO TO 4
4.REPEAT STEPS E
Repeat steps 1 to 3 twice.
F
>> GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON. G
>> GO TO 6
SRC
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-85, "Trouble Diag-
nosis without CONSULT-III". I
>> END
J
Diagnosis Procedure (Component Diagnosis) INFOID:0000000001735326
>> GO TO 4 P
>> GO TO 5
5.RELATED HARNESS
Revision: March 2010 SRC-39 2008 QX56
B1145 – B1148 SIDE CURTAIN AIR BAG MODULE RH (REAR)
< COMPONENT DIAGNOSIS >
Replace the related harness.
>> END
I
Without CONSULT-lll
WHIA0263E
1.INSPECTION START
Turn ignition switch ON. N
>> GO TO 2.
2.CHECK SELF-DIAG RESULT O
>> GO TO 2
2.IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3
3.WAIT TIME
Wait more than 3 seconds.
>> GO TO 4
4.REPEAT STEPS
Repeat steps 1 to 3 twice.
>> GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 6
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-85, "Trouble Diag-
nosis without CONSULT-III".
>> END
Diagnosis Procedure (Component Diagnosis) INFOID:0000000001735329
>> GO TO 4
4.AIR BAG DIAGNOSIS SENSOR UNIT
Replace the air bag diagnosis sensor unit. Refer to SR-17, "Removal and Installation".
>> GO TO 5
5.RELATED HARNESS
Revision: March 2010 SRC-42 2008 QX56
B1086 – B1089 SEAT BELT PRE-TENSIONER LH
< COMPONENT DIAGNOSIS >
Replace the related harness.
A
>> END
SRC
PART LOCATION
Refer to SRC-7, "SRS Component Parts Location".
DTC Logic INFOID:0000000001735331
Without CONSULT-lll
WHIA0262E
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check for the DTC on CONSULT-lll.
Is the DTC detected?
YES >> Refer to SRC-45, "Diagnosis Procedure (Component Diagnosis)".
NO >> Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.IGNITION SWITCH
Revision: March 2010 SRC-44 2008 QX56
B1081 – B1084 SEAT BELT PRE-TENSIONER RH
< COMPONENT DIAGNOSIS >
Turn ignition switch ON.
A
>> GO TO 2
2.IGNITION SWITCH B
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3 C
3.WAIT TIME
Wait more than 3 seconds. D
>> GO TO 4
4.REPEAT STEPS E
Repeat steps 1 to 3 twice.
F
>> GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON. G
>> GO TO 6
SRC
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-85, "Trouble Diag-
nosis without CONSULT-III". I
>> END
J
Diagnosis Procedure (Component Diagnosis) INFOID:0000000001735332
>> GO TO 4 P
>> GO TO 5
5.RELATED HARNESS
Revision: March 2010 SRC-45 2008 QX56
B1081 – B1084 SEAT BELT PRE-TENSIONER RH
< COMPONENT DIAGNOSIS >
Replace the related harness.
>> END
I
Without CONSULT-lll
WHIA0251E
1.INSPECTION START
Turn ignition switch ON. N
>> GO TO 2.
2.CHECK SELF-DIAG RESULT O
>> GO TO 2
2.IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3
3.WAIT TIME
Wait more than 3 seconds.
>> GO TO 4
4.REPEAT STEPS
Repeat steps 1 to 3 twice.
>> GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 6
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-85, "Trouble Diag-
nosis without CONSULT-III".
>> END
Diagnosis Procedure (Component Diagnosis) INFOID:0000000001735335
>> GO TO 4
4.AIR BAG DIAGNOSIS SENSOR UNIT
Replace the air bag diagnosis sensor unit. Refer to SR-17, "Removal and Installation".
>> GO TO 5
5.RELATED HARNESS
Revision: March 2010 SRC-48 2008 QX56
B1182 - B1185 SEAT BELT BUCKLE PRE-TENSIONER LH
< COMPONENT DIAGNOSIS >
Replace the related harness.
A
>> END
SRC
PART LOCATION
Refer to SRC-7, "SRS Component Parts Location".
DTC Logic INFOID:0000000001735337
Without CONSULT-lll
WHIA0250E
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check for the DTC on CONSULT-lll.
Is the DTC detected?
YES >> Refer to SRC-51, "Diagnosis Procedure (Component Diagnosis)".
NO >> Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.IGNITION SWITCH
Revision: March 2010 SRC-50 2008 QX56
B1177 - B1180 SEAT BELT BUCKLE PRE-TENSIONER RH
< COMPONENT DIAGNOSIS >
Turn ignition switch ON.
A
>> GO TO 2
2.IGNITION SWITCH B
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3 C
3.WAIT TIME
Wait more than 3 seconds. D
>> GO TO 4
4.REPEAT STEPS E
Repeat steps 1 to 3 twice.
F
>> GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON. G
>> GO TO 6
SRC
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-85, "Trouble Diag-
nosis without CONSULT-III". I
>> END
J
Diagnosis Procedure (Component Diagnosis) INFOID:0000000001735338
>> GO TO 4 P
>> GO TO 5
5.RELATED HARNESS
Revision: March 2010 SRC-51 2008 QX56
B1177 - B1180 SEAT BELT BUCKLE PRE-TENSIONER RH
< COMPONENT DIAGNOSIS >
Replace the related harness.
>> END
K
WHIA0200E
>> GO TO 2.
2.CHECK SELF-DIAG RESULT N
Check for the DTC on CONSULT-lll.
Is the DTC detected?
O
YES >> Refer to SRC-54, "Diagnosis Procedure (Component Diagnosis)".
NO >> Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll) P
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2
>> GO TO 3
3.WAIT TIME
Wait more than 3 seconds.
>> GO TO 4
4.REPEAT STEPS
Repeat steps 1 to 3 twice.
>> GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 6
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-85, "Trouble Diag-
nosis without CONSULT-III".
>> END
Diagnosis Procedure (Component Diagnosis) INFOID:0000000001735341
>> GO TO 4
4.AIR BAG DIAGNOSIS SENSOR UNIT
Replace the air bag diagnosis sensor unit. Refer to SR-17, "Removal and Installation".
>> GO TO 5
5.RELATED HARNESS
Replace the related harness.
SRC
PART LOCATION
Refer to SRC-7, "SRS Component Parts Location".
DTC Logic INFOID:0000000001735343
SATELLITE SENS LH B1118 LH side air bag satellite sensor has mal- 1. Visually check the wiring harness connection.
[UNIT FAIL] functioned. 2. Replace the harness if it has visible damage.
B1119
3. Replace the LH side air bag satellite sensor.
SATELLITE SENS LH LH side air bag satellite sensor communi- 4. Replace the air bag diagnosis sensor unit.
B1120
[COMM FAIL] cation error. 5. Replace the related harness.
Without CONSULT-lll
WHIA0204E
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check for the DTC on CONSULT-lll.
Is the DTC detected?
YES >> Refer to SRC-57, "Diagnosis Procedure (Component Diagnosis)".
NO >> Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2
>> GO TO 3 B
3.WAIT TIME
Wait more than 3 seconds.
C
>> GO TO 4
4.REPEAT STEPS D
Repeat steps 1 to 3 twice.
E
>> GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON. F
>> GO TO 6
6.DIAGNOSTIC MODE G
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-85, "Trouble Diag-
nosis without CONSULT-III". SRC
>> END
I
Diagnosis Procedure (Component Diagnosis) INFOID:0000000001735344
>> GO TO 4 O
4.AIR BAG DIAGNOSIS SENSOR UNIT
Replace the air bag diagnosis sensor unit. Refer to SR-17, "Removal and Installation". P
>> GO TO 5
5.RELATED HARNESS
Replace the related harness.
K
WHIA0203E
>> GO TO 2.
2.CHECK SELF-DIAG RESULT N
Check for the DTC on CONSULT-lll.
Is the DTC detected?
O
YES >> Refer to SRC-60, "Diagnosis Procedure (Component Diagnosis)".
NO >> Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll) P
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2
>> GO TO 3
3.WAIT TIME
Wait more than 3 seconds.
>> GO TO 4
4.REPEAT STEPS
Repeat steps 1 to 3 twice.
>> GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 6
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-85, "Trouble Diag-
nosis without CONSULT-III".
>> END
Diagnosis Procedure (Component Diagnosis) INFOID:0000000001735347
>> GO TO 4
4.AIR BAG DIAGNOSIS SENSOR UNIT
Replace the air bag diagnosis sensor unit. Refer to SR-17, "Removal and Installation".
>> GO TO 5
5.RELATED HARNESS
Replace the related harness.
SRC
PART LOCATION
Refer to SRC-7, "SRS Component Parts Location".
DTC Logic INFOID:0000000001735349
Without CONSULT-lll
WHIA0198E
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check for the DTC on CONSULT-lll.
Is the DTC detected?
YES >> Refer to SRC-63, "Diagnosis Procedure (Component Diagnosis)".
NO >> Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2
>> GO TO 3 B
3.WAIT TIME
Wait more than 3 seconds.
C
>> GO TO 4
4.REPEAT STEPS D
Repeat steps 1 to 3 twice.
E
>> GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON. F
>> GO TO 6
6.DIAGNOSTIC MODE G
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-85, "Trouble Diag-
nosis without CONSULT-III". SRC
>> END
I
Diagnosis Procedure (Component Diagnosis) INFOID:0000000001735350
>> GO TO 4 O
4.RELATED HARNESS
Replace the related harness. P
>> END
PART LOCATION
Refer to SRC-7, "SRS Component Parts Location".
DTC Logic INFOID:0000000001735352
Without CONSULT-lll
WHIA0212E
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check for the DTC on CONSULT-lll.
Is the DTC detected?
YES >> Refer to SRC-65, "Diagnosis Procedure (Component Diagnosis)".
NO >> Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.IGNITION SWITCH
Turn ignition switch ON.
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
B
>> GO TO 3
3.WAIT TIME
C
Wait more than 3 seconds.
>> GO TO 4 D
4.REPEAT STEPS
Repeat steps 1 to 3 twice.
E
>> GO TO 5
5.IGNITION SWITCH F
Turn ignition switch ON.
>> GO TO 6 G
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-85, "Trouble Diag- SRC
nosis without CONSULT-III".
>> END I
Diagnosis Procedure (Component Diagnosis) INFOID:0000000001735353
>> GO TO 5
5.RELATED HARNESS
Replace the related harness.
PART LOCATION
Refer to SRC-7, "SRS Component Parts Location". D
DTC Logic INFOID:0000000006081143
With CONSULT-lll
F
CONSULT-III name DTC DTC detecting condition Repair order
B1017 The OCS control unit is malfunctioning. 1. Replace the RH front seat cushion assembly.
Do not disassemble the seat cushion assem-
B1021 bly. G
OCCUPANT SENS C/U The OCS control unit is malfunctioning. 1. Replace the harness if it has visible damage.
[UNIT FAIL] 2. Replace the RH front seat cushion assembly.
B1020 Do not disassemble the seat cushion assem- SRC
bly.
3. Replace the RH front seat belt assembly.
The OCS sensor is malfunctioning. 1. Visually check the wiring harness connection I
to the OCS sensor.
OCCUPANT SENS
B1018 2. Replace the RH front seat cushion assembly.
[UNIT FAIL]
Do not disassemble the seat cushion assem-
bly. J
The belt tension sensor is malfunctioning. 1. Visually check the wiring harness connection.
2. Replace the harness if it has visible damage.
3. Replace the RH front seat belt assembly. K
BELT TENSION SENS
B1019 4. Replace the RH front seat cushion assembly.
[UNIT FAIL]
Do not disassemble the seat cushion assem-
bly.
5. Replace the related harness. L
Communication between the OCS control 1. Visually check the wiring harness connection.
unit and the air bag diagnosis sensor unit is 2. Replace the harness if it has visible damage.
interrupted. 3. Replace the RH front seat cushion assembly.
OCCUPANT SENS C/U M
B1022 Do not disassemble the seat cushion assem-
[COMM FAIL]
bly.
4. Replace the air bag diagnosis sensor unit.
5. Replace the related harness. N
Without CONSULT-lll
O
WHIA0211E
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check for the DTC on CONSULT-lll.
Is the DTC detected?
YES >> Refer to SRC-68, "Diagnosis Procedure (Component Diagnosis)".
NO >> Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2
2.IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3
3.WAIT TIME
Wait more than 3 seconds.
>> GO TO 4
4.REPEAT STEPS
Repeat steps 1 to 3 twice.
>> GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 6
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-7, "SRS Compo-
nent Parts Location".
>> END
Diagnosis Procedure (Component Diagnosis) INFOID:0000000006081144
>> GO TO 13
13.REPLACE RH FRONT SEAT CUSHION ASSEMBLY
Replace the RH front seat cushion assembly. Refer to SE-49, "Removal and Installation".
>> GO TO 14
14.AIR BAG DIAGNOSIS SENSOR UNIT
Replace the air bag diagnosis sensor unit. Refer to SR-17, "Removal and Installation".
>> END.
PART LOCATION
Refer to SRC-7, "SRS Component Parts Location". D
DTC Logic INFOID:0000000001735358
With CONSULT-lll
F
CONSULT-III name DTC DTC detecting condition Repair order
FRONTAL COLLISION Driver and/or front passenger air bag mod- Refer to SR-19, "For Frontal Collision".
B1209
DETECTION ules are deployed.
G
SIDE COLLISION DE- Side and/or curtain air bag modules are Refer to SR-20, "For Side and Rollover Collision".
B1210
TECTION deployed.
ROLLOVER DETEC- Curtain air bag module and seat belt pre-
B1211 SRC
TION tensioner are deployed.
>> GO TO 2.
2.CHECK SELF-DIAG RESULT K
Check for the DTC on CONSULT-lll.
Is the DTC detected?
L
YES >> Refer to SRC-71, "Diagnosis Procedure (Component Diagnosis)".
NO >> Inspection End.
Diagnosis Procedure (Component Diagnosis) INFOID:0000000001735359
M
Refer to SR-19, "For Frontal Collision" or SR-20, "For Side and Rollover Collision".
AWHWA0002GB
SRC
AAHWA0013GB
ALHIA0057GB
SRC
AAHIA0012GB
ALHIA0059GB
SRC
ALHIA0060GB
AWHIA0028GB
SRC
ALHIA0062GB
AWHIA0029GB
SRC
ALHIA0071GB
CURTAIN MODULE LH LH side curtain air bag module (rear) cir- 1. Visually check the wiring harness connection.
B1150
[OPEN] cuit is open. 2. Replace the harness if it has visible damage.
3. Replace the LH side curtain air bag module. J
CURTAIN MODULE LH LH side curtain air bag module (rear) cir-
B1151 4. Replace the air bag diagnosis sensor unit.
[VB-SHORT] cuit is shorted to a power supply circuit.
5. Replace the related harness.
CURTAIN MODULE LH LH side curtain air bag module (rear) cir-
B1152 K
[GND-SHORT] cuit is shorted to ground.
CURTAIN MODULE LH LH side curtain air bag module (rear) cir-
B1153
[SHORT] cuits are shorted to each other.
L
CURTAIN MODULE RH RH side curtain air bag module (rear) 1. Visually check the wiring harness connection.
B1145
[OPEN] circuit is open. 2. Replace the harness if it has visible damage.
3. Replace the RH side curtain air bag module.
RH side curtain air bag module (rear)
CURTAIN MODULE RH 4. Replace the air bag diagnosis sensor unit. M
B1146 circuit is shorted to a power supply cir-
[VB-SHORT] 5. Replace the related harness.
cuit.
CURTAIN MODULE RH RH side curtain air bag module (rear)
B1147
[GND-SHORT] circuit is shorted to ground. N
CURTAIN MODULE RH RH side curtain air bag module (rear)
B1148
[SHORT] circuits are shorted to each other.
PRE-TEN FRONT LH LH seat belt pre-tensioner circuit is 1. Visually check the wiring harness connection. O
B1086
[OPEN] open. 2. Replace the harness if it has visible damage.
3. Replace the front LH seat belt pre-tensioner.
PRE-TEN FRONT LH LH seat belt pre-tensioner circuit is
B1087 4. Replace the air bag diagnosis sensor unit.
[VB-SHORT] shorted to a power supply circuit. P
5. Replace the related harness.
PRE-TEN FRONT LH LH seat belt pre-tensioner circuit is
B1088
[GND-SHORT] shorted to ground.
PRE-TEN FRONT LH LH seat belt pre-tensioner circuits are
B1089
[SHORT] shorted to each other.
CRASH ZONE SEN B1033 Crash zone sensor has malfunctioned. 1. Visually check the wiring harness connection.
[UNIT FAIL] 2. Replace the harness if it has visible damage.
B1034
3. Replace the crash zone sensor.
CRASH ZONE SEN Crash zone sensor communication er- 4. Replace the air bag diagnosis sensor unit.
B1035
[COMM FAIL] ror. 5. Replace the related harness.
SATELLITE SENS LH B1118 LH side air bag satellite sensor has mal- 1. Visually check the wiring harness connection.
[UNIT FAIL] functioned. 2. Replace the harness if it has visible damage.
B1119
3. Replace the LH side air bag satellite sensor.
SATELLITE SENS LH LH side air bag satellite sensor commu- 4. Replace the air bag diagnosis sensor unit.
B1120
[COMM FAIL] nication error. 5. Replace the related harness.
SATELLITE SENS RH B1113 RH side air bag satellite sensor has mal- 1. Visually check the wiring harness connection.
[UNIT FAIL] functioned. 2. Replace the harness if it has visible damage.
B1114
3. Replace the RH side air bag satellite sensor.
SATELLITE SENS RH RH side air bag satellite sensor commu- 4. Replace the air bag diagnosis sensor unit.
B1115
[COMM FAIL] nication error. 5. Replace the related harness.
Air bag diagnosis sensor unit is malfunc- 1. Visually check the wiring harness connection.
tioning. 2. Replace the harness if it has visible damage.
CONTROL UNIT B1XXX
3. Replace the air bag diagnosis sensor unit.
4. Replace the related harness.
Front passenger air bag OFF indicator is 1. Visually check the wiring harness connection.
malfunctioning. 2. Replace the harness if it has visible damage.
3. Replace the front passenger air bag OFF in-
PASS A/B INDCTR CKT B1023
dicator.
4. Replace the air bag diagnosis sensor unit.
5. Replace the related harness.
B1017 The OCS control unit is malfunctioning. 1. Replace the RH front seat cushion assembly.
Do not disassemble the seat cushion assem-
B1021 bly.
OCCUPANT SENS C/U The OCS control unit is malfunctioning. 1. Replace the harness if it has visible damage.
[UNIT FAIL] 2. Replace the RH front seat cushion assembly.
B1020 Do not disassemble the seat cushion assem-
bly.
3. Replace the RH front seat belt assembly.
I
WARNING LAMP FLASH CODE CHART
NOTE:
Follow the procedures in numerical order when repairing malfunctioning parts. Confirm whether malfunction is J
eliminated using air bag warning lamp each time repair is finished. If malfunction is still observed, proceed to
the next step. When malfunction is eliminated, further repair work is not required.
K
SHIA0026E
N
WHIA0260E
WHIA0198E
WHIA0261E
WHIA0200E
WHIA0262E
WHIA0263E
C
WHIA0250E
WHIA0251E
G
SRC
J
WHIA0203E
WHIA0204E
WHIA0264E
WHIA0265E
WHIA0255E
WHIA0253E
WHIA0254E
WHIA0252E
C
WHIA0211E
WHIA0212E
G
SRC
DIAGNOSTIC PROCEDURE 7
1.CHECK CONDITION OF AIR BAG MODULE
Inspect for any deployed air bag modules or seat belt pre-tensioners.
Are any air bag modules or seat belt pre-tensioners deployed?
YES >> Refer to SR-19, "For Frontal Collision" or SR-20, "For Side and Rollover Collision".
NO >> GO TO 2
2.CHECK THE AIR BAG FUSE
Check 10A fuse [No. 13, located in the fuse block (J/B)].
Is the fuse blown?
Yes >> GO TO 3
No >> GO TO 4
3.CHECK AIR BAG FUSE AGAIN
Replace 10A fuse [No. 13, located in the fuse block (J/B)] and turn ignition switch ON.
Does the fuse blow again?
YES >> Replace harness.
NO >> Inspection End.
4.CHECK AIR BAG DIAGNOSIS SENSOR UNIT
Connect CONSULT-III.
Is “AIR BAG” displayed on CONSULT-III?
YES >> GO TO 5
NO >> Visually inspect the air bag diagnosis sensor unit harness connections. If the connections are OK,
replace the air bag diagnosis sensor unit. Refer to SR-17, "Removal and Installation".
5.CHECK HARNESS CONNECTION
Check for loose connections between the combination meter and the air bag diagnosis sensor unit.
Are there any loose connections?
Yes >> Properly connect the combination meter and air bag diagnosis sensor unit harness connectors. If
“AIR BAG” warning lamp still does not turn off, replace the wiring harness.
No >> Replace air bag diagnosis sensor unit.
"AIR BAG" Warning Lamp Does Not Turn On INFOID:0000000001735364
DIAGNOSTIC PROCEDURE 8
1.CHECK METER FUSE
Check the 10A fuse [No. 14, located in the fuse block (J/B)] .
Is the fuse blown?
Yes >> GO TO 2
No >> GO TO 3
2.REPLACE METER FUSE AND CHECK AGAIN
Replace 10A fuse [No. 14, located in the fuse block (J/B)] and turn ignition switch ON.
Does the fuse blow again?
Yes >> Replace harness.
No >> Inspection End.
3.CHECK HARNESS CONNECTIONS BETWEEN AIR BAG DIAGNOSIS SENSOR UNIT AND COMBINA-
Revision: March 2010 SRC-90 2008 QX56
SRS AIR BAG SYSTEM
< SYMPTOM DIAGNOSIS >
TION METER
Inspect the harness and connectors between the air bag diagnosis sensor unit and the combination meter. A
Do the harness or connectors have any visible damage?
Yes >> Replace harness.
No >> GO TO 4 B
SRC
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. D
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING: E
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
F
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this G
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS SRC
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a I
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the J
battery, and wait at least 3 minutes before performing any service.
Precaution for SRS "AIR BAG" and "SEAT BELT PRE-TENSIONER" Service
INFOID:0000000001735367 K
• Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 min-
utes. L
For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-
tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have
passed. M
• The air bag diagnosis sensor unit must always be installed with the arrow mark “⇐” pointing toward the front
of the vehicle for proper operation. Also check air bag diagnosis sensor unit for cracks, deformities or rust
before installation and replace as required.
• The spiral cable must be aligned with the neutral position since its rotations are limited. Do not attempt to N
turn steering wheel or column after removal of steering gear.
• Handle air bag module carefully. Always place driver and front passenger air bag modules with the pad side
facing upward and seat mounted front side air bag module standing with the stud bolt side facing down. O
• Conduct self-diagnosis to check entire SRS for proper function after replacing any components.
• After air bag inflates, the front instrument panel assembly should be replaced if damaged.
Occupant Classification System Precaution INFOID:0000000001735368 P
Replace occupant classification system control unit and passenger front seat cushion as an assembly.