Srs Airbag Control System: Section

RESTRAINTS
SRS AIRBAG CONTROL SYSTEM

SECTION SRC B
E
CONTENTS
BASIC INSPECTION .................................... 3 Description ...............................................................16 F
DTC Logic ................................................................16
DIAGNOSIS AND REPAIR WORK FLOW ......... 3 Diagnosis Procedure (Component diagnosis) .......17
Work Flow ................................................................. 3 G
B1065 – B1068, B1070 – B1073 PASSEN-
INTERMITTENTS INCIDENT .............................. 5 GER AIRBAG MODULE ................................... 19
Inspection Procedure ............................................... 5 Description ...............................................................19
Trouble Diagnosis with CONSULT-III ....................... 5 DTC Logic ................................................................19 SRC
Diagnosis Procedure (Component diagnosis) .......20
FUNCTION DIAGNOSIS ............................... 6
B1134 – B1137 SIDE AIRBAG MODULE LH ... 22 I
SRS AIR BAG SYSTEM ...................................... 6 Description ...............................................................22
SRS Configuration .................................................... 6 DTC Logic ................................................................22
SRS Component Parts Location ............................... 7 Diagnosis Procedure (Component diagnosis) .......23
Driver Air Bag Module ............................................... 7 J
Front Passenger Air Bag Module .............................. 8 B1129 – B1132 SIDE AIRBAG MODULE RH ... 25
Front Side Air Bag ..................................................... 8 Description ...............................................................25
Side Curtain Air Bag .................................................. 8 DTC Logic ................................................................25 K
Front Seat Belt Pre-tensioner with Load Limiter ...... 8 Diagnosis Procedure (Component diagnosis) .......26
Direct-connect SRS Component Connectors ............ 9
B1150 – B1153 SIDE CURTAIN AIR BAG
OCCUPANT CLASSIFICATION SYSTEM .........10 L
MODULE LH ..................................................... 28
System Diagram ...................................................... 10 Description ...............................................................28
Occupant Classification System (OCS) .................. 10 DTC Logic ................................................................28
Diagnosis Procedure (Component diagnosis) .......29 M
PASSENGER SEAT BELT WARNING SYS-
TEM ....................................................................11 B1145 – B1148 SIDE CURTAIN AIR BAG
System Diagram ...................................................... 11 MODULE RH ..................................................... 31 N
System Description ................................................. 11 Description ...............................................................31
Component Parts Location ...................................... 11 DTC Logic ................................................................31
Diagnosis Procedure (Component diagnosis) .......32
ON BOARD DIAGNOSTIC (OBD) SYSTEM ......12 O
Trouble Diagnosis Introduction ............................... 12 B1086 – B1089 SEAT BELT PRE-TENSION-
SRS Operation Check ............................................. 12 ER LH ................................................................ 34
Trouble Diagnosis without CONSULT-III ................ 14 Description ...............................................................34 P
CONSULT-III Function (AIR BAG) .......................... 14 DTC Logic ................................................................34
Self-Diagnosis Function (Without CONSULT-III) .... 14 Diagnosis Procedure (Component diagnosis) .......35
COMPONENT DIAGNOSIS ......................... 16 B1081 – B1084 SEAT BELT PRE-TENSION-
ER RH ................................................................ 37
B1049 – B1052, B1054 – B1057 DRIVER AIR-
Description ...............................................................37
BAG MODULE ...................................................16 DTC Logic ................................................................37
Revision: August 2007 SRC-1 2008 Altima Hybrid

Diagnosis Procedure (Component diagnosis) ...... 38 B1209 – B1210 COLLISION DETECTION ........ 58
Description .............................................................. 58
B1033 – B1035 CRASH ZONE SENSOR ......... 40 DTC Logic ............................................................... 58
Description .............................................................. 40 Diagnosis Procedure (Component diagnosis) ...... 58
DTC Logic ............................................................... 40
Diagnosis Procedure (Component diagnosis) ...... 41 ECU DIAGNOSIS ....................................... 59
B1118 – B1120 SATELLITE SENSOR LH ........ 43 DIAGNOSIS SENSOR UNIT ............................. 59
Description .............................................................. 43 Wiring Diagram ....................................................... 59
DTC Logic ............................................................... 43 Trouble Diagnosis with CONSULT-III ..................... 68
Diagnosis Procedure (Component diagnosis) ...... 44 Trouble Diagnosis without CONSULT-III ................ 71
B1113 – B1115 SATELLITE SENSOR RH ....... 46 SYMPTOM DIAGNOSIS ............................ 75
Description .............................................................. 46
DTC Logic ............................................................... 46 SRS AIR BAG SYSTEM .................................... 75
Diagnosis Procedure (Component diagnosis) ...... 47 "AIR BAG" Warning Lamp Does Not Turn Off ........ 75
"AIR BAG" Warning Lamp Does Not Turn On ........ 75
B1XXX AIR BAG DIAGNOSIS SENSOR UNIT... 49
Description .............................................................. 49 PASSENGER SEAT BELT WARNING SYS-
DTC Logic ............................................................... 49 TEM .................................................................... 77
Diagnosis Procedure (Component diagnosis) ...... 50 Seat Belt Warning System Does Not Function ....... 77
B1023 PASSENGER AIR BAG OFF INDICA- PRECAUTION ............................................ 78
TOR .................................................................... 52
Description .............................................................. 52 PRECAUTIONS ................................................. 78
DTC Logic ............................................................... 52 Precaution for Supplemental Restraint System
Diagnosis Procedure (Component diagnosis) ...... 53 (SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ................................................................. 78
B1017, B1018, B1020 – B1022 OCCUPANT Precaution for SRS "AIR BAG" and "SEAT BELT
CLASSIFICATION SYSTEM ............................. 55 PRE-TENSIONER" Service .................................... 78
Description .............................................................. 55 Occupant Classification System Precaution ........... 78
DTC Logic ............................................................... 55
Diagnosis Procedure (Component diagnosis) ...... 56

DIAGNOSIS AND REPAIR WORK FLOW
< BASIC INSPECTION >
BASIC INSPECTION A
Work Flow INFOID:0000000003070611
B
OVERALL SEQUENCE
C
SRC
M
WHIA0348E
*1 SRC-12, "Trouble Diagnosis Intro- *2 SRC-12, "SRS Operation Check" *3 SRC-5, "Trouble Diagnosis with N
duction" CONSULT-III"
*4 SRC-14, "Self-Diagnosis Function
(Without CONSULT-III)"
O
DETAILED WORK FLOW
1.CUSTOMER INFORMATION
P
Get detailed information from the customer about the symptom.
>> GO TO 2
2.PRELIMINARY CHECK
Perform preliminary check. Refer to SRC-12, "Trouble Diagnosis Introduction".

>> GO TO 3
3.TECHNICAL SERVICE BULLETINS
Check for technical service bulletins.
>> GO TO 4
4.USER MODE
Perform self-diagnosis using the "AIR BAG" warning lamp in User mode. Refer to SRC-12, "SRS Operation
Check".
>> GO TO 5
5.SELF-DIAGNOSIS
Perform SELF-DIAGNOSIS. Refer to SRC-5, "Trouble Diagnosis with CONSULT-III" (w/CONSULT-III) or
SRC-14, "Self-Diagnosis Function (Without CONSULT-III)" (w/o CONSULT- III).
>> GO TO 6
6.REPLACE PART
Replace the malfunctioning part.
>> GO TO 7
7.FINAL CHECK
Check SRS using Diagnosis mode and User mode.
Does Diagnosis mode and User mode indicate SRS normal?
YES >> Inspection end.
NO >> GO TO 5

INTERMITTENTS INCIDENT
INTERMITTENTS INCIDENT
A
Inspection Procedure INFOID:0000000003070612
INTERMITTENT TROUBLE B
An intermittent incident may have occured in the past but is not being detected currently. This DTC will not be
detected on SELF DIAG [CURRENT], but may be viewed on SELF DIAG [PAST] using CONSULT-III.
Trouble Diagnosis with CONSULT-III INFOID:0000000003070613
C
DIAGNOSTIC PROCEDURE 4
D
Check SRS Repair History
1.CONSIDER POSSIBILITY THAT SELF-DIAGNOSTIC RESULT WAS NOT ERASED AFTER REPAIR
E
Check repair history of the SRS.
Have any previous repairs been made to the SRS?
Yes >> Self-diagnostic result “SELF-DIAG [PAST]” (previously stored in the memory) might not be erased
F
after repair. Proceed to "DIAGNOSTIC PROCEDURE 3". Refer to SRC-14, "Self-Diagnosis Func-
tion (Without CONSULT-III)".
No >> Proceed to "DIAGNOSTIC PROCEDURE 2". Refer to SRC-12, "SRS Operation Check".
G
SRC

SRS AIR BAG SYSTEM
< FUNCTION DIAGNOSIS >
FUNCTION DIAGNOSIS
SRS AIR BAG SYSTEM
SRS Configuration INFOID:0000000003070614
WHIA0186E
The air bag deploys if the air bag diagnosis sensor unit is activated while the ignition switch is in the ON or
START position.
The collision modes for which supplemental restraint systems are activated are different among the SRS sys-
tems. For example, the driver air bag module, front passenger air bag module and front seat belt pre-tension-
ers are activated in a frontal collision but not in a side collision.
SRS configurations for some collision modes are as follows:
SRS configuration Frontal collision Left side collision Right side collision
Driver air bag module × — —
Front passenger air bag module × — —
Front LH seat belt pre-tensioner × — —
Front RH seat belt pre-tensioner × — —
Front LH side air bag module — × —
Front RH side air bag module — — ×
LH side curtain air bag module — × —
RH side curtain air bag module — — ×

SRS AIR BAG SYSTEM
SRS Component Parts Location INFOID:0000000003070615
SRC
WHIA0329E
I
1. Crash zone sensor 2. Spiral cable 3. Front passenger air bag off indicator
4. Front LH seatbelt pre-tensioner 5. Air bag diagnosis sensor unit 6. Front LH side air bag module
LH side air bag (satellite) sensor J
7. Seat belt buckle switch (LH) 8. Occupant classification system 9. Front RH seatbelt pre-tensioner
Seat belt buckle switch (RH) control unit and sensor mat RH side air bag (satellite) sensor
10. Front RH side air bag module 11. RH side curtain air bag module 12. LH side curtain air bag module
K
13. Front passenger air bag module 14. Driver air bag module
Driver Air Bag Module INFOID:0000000003070616

L
The driver air bag module is dual stage and located in the steering
wheel assembly. It operates with the SRS system in a frontal colli-
sion exceeding a specified level. M
O
ALHIA0023ZZ

SRS AIR BAG SYSTEM
Front Passenger Air Bag Module INFOID:0000000003070617
The front passenger air bag module is located behind the instrument
panel assembly. It operates with the SRS system in a frontal colli-
sion exceeding a specified level. Refer to SRC-10, "Occupant Clas-
sification System (OCS)" for more information.
ALHIA0024ZZ
Front Side Air Bag INFOID:0000000003070618
Front side air bag modules are built into the front seatback assem-
blies. Vehicles with side air bags are equipped with labels as shown.
WHIA0327E
Side Curtain Air Bag INFOID:0000000003070619
Side curtain air bag modules are located above the vehicle headlining.
Vehicles with side curtain air bags are equipped with labels as
shown.
WHIA0041E
Front Seat Belt Pre-tensioner with Load Limiter INFOID:0000000003070620
The seat belt pre-tensioner system with load limiter is installed for
both the driver's seat and the front passenger's seat. It operates
simultaneously with the SRS air bag system in the event of a frontal
collision with an impact exceeding a specified level.
When the frontal collision with an impact exceeding a specified level
occurs, seat belt slack resulting from clothing or other factors is
immediately taken up by the pre-tensioner. Vehicle passengers are
securely restrained.
When passengers in a vehicle are thrown forward in a collision and
the restraining force of the seat belt exceeds a specified level, the
load limiter permits the specified extension of the seat belt by the
ALHIA0025ZZ
twisting of the ELR shaft, and a relaxation of the chest-area seat belt
web tension while maintaining force.

SRS AIR BAG SYSTEM
Direct-connect SRS Component Connectors INFOID:0000000003070621
A
The following SRS components use direct-connect style harness connectors.
• Driver front air bag module
• Passenger front air bag module B
• LH side curtain air bag module
• RH side curtain air bag module
• Front LH seat belt pre-tensioner
• Front RH seat belt pre-tensioner C
Always pull up to release locking tab prior to removing connector from SRS component.
Always push down to lock locking tab after installing connector to
SRS component. When locked, the locking tab is level with the con- D
nector housing.
WHIA0103E
SRC

OCCUPANT CLASSIFICATION SYSTEM
OCCUPANT CLASSIFICATION SYSTEM
System Diagram INFOID:0000000003070622
ALHIA0026GB
Occupant Classification System (OCS) INFOID:0000000003070623
The occupant classification system (OCS) identifies if a child or child seat is present in the front passenger
seat. The OCS receives inputs from the occupant classification sensor mat (located inside the passenger seat
cushion assembly). Depending on classification of the passenger, the OCS control unit sends a signal to the
air bag diagnosis sensor unit. The air bag diagnosis sensor unit uses this signal and the seat belt buckle
switch RH signal to determine deployment or non deployment of the front passenger air bag module in the
event of a collision. Depending on the signals received, the air bag diagnosis sensor unit can disable the front
passenger air bag module completely.
NOTE:
In case of customer concern, CONSULT-III can be used to confirm the front passenger air bag status (readi-
ness).
Front Passenger Air Bag Status Conditions
Front Passenger Seat PASS AIR BAG OFF Indicator Front Passenger Air Bag Status
CONSULT-III Display
(Condition) (Status) (Readiness)
Seat occupied OFF Active (enabled) ON
Seat occupied NOTE ON Deactivated (disabled) OFF

Seat empty OFF Deactivated (disabled) OFF
NOTE:
Passenger does not meet Occupant Classification System specifications for passenger air bag activation.
ALHIA0027ZZ
1. Seat cushion foam 2. OCS control unit 3. OCS sensor mat

4. OCS sensor mat cell (internal)

PASSENGER SEAT BELT WARNING SYSTEM
A
System Diagram INFOID:0000000003070624
ALHIA0028GB
G
System Description INFOID:0000000003070625
The passenger seat belt warning system will remind the driver if the SRC
driver or front passenger seat belt should be buckled. The system
works in conjunction with the occupant classification system. Refer
to SRC-10, "Occupant Classification System (OCS)".
I
ALHIA0032ZZ K
Passenger Seat Belt Warning System Operation

Driver seat status Passenger seat status Seat belt buckle switch Seat belt buckle switch Seat belt warning lamp L
(Ignition switch ON) LH status RH status
Buckled Off
Seat occupied
Buckled Unbuckled On M
Seat occupied
Seat unoccupied Off
—
— Unbuckled On
N
Component Parts Location INFOID:0000000003070626
Refer to SRC-7, "SRS Component Parts Location".

O

ON BOARD DIAGNOSTIC (OBD) SYSTEM
Trouble Diagnosis Introduction INFOID:0000000003070627
CAUTION:
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to do so in
this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harness con-
nectors.
• Do not attempt to repair, splice or modify SRS wiring harnesses. If a harness is damaged, replace it
with a new one.
• Keep ground connections clean.
DIAGNOSIS FUNCTION
The SRS self-diagnosis results can be read by using “AIR BAG” warning lamp and/or CONSULT-III.
The User mode is exclusively prepared for the customer (driver). This mode warns the driver of a system mal-
function through the operation of the “AIR BAG” warning lamp.
The Diagnosis mode allows the technician to locate and inspect the malfunctioning part.
The mode applications for the “AIR BAG” warning lamp and CONSULT-III are as follows:
User mode Diagnosis mode Display type

“AIR BAG” warning lamp X X ON-OFF operation
CONSULT-III — X Monitoring
HOW TO PERFORM TROUBLE DIAGNOSES FOR QUICK AND ACCURATE REPAIR

A good understanding of the malfunction conditions can make troubleshooting faster and more accurate.
In general, each customer feels differently about a malfunction. It is important to fully understand the symp-
toms or conditions for a customer complaint.
Information From Customer
WHAT - Vehicle model
WHEN - Date, Frequencies
WHERE - Road conditions
HOW - Operating conditions, Symptoms
Preliminary Check
Check that the following parts are in good order.
• Battery (Refer to PG-2, "How to Handle Battery".)
• Fuse (Refer to SRC-59, "Wiring Diagram".)
• System component-to-harness connections
SRS Operation Check INFOID:0000000003070628
Checking SRS Operation Using “AIR BAG” Warning Lamp—User Mode
1. Turn the ignition switch from OFF to ON, and check that the air bag warning lamp blinks.
2. Compare the SRS air bag warning lamp blinking pattern with the
examples.
BF-1845D

SRS Air bag warning lamp examples
“AIR BAG” warning lamp (User mode) SRS condition Reference item A
• No malfunction is detected.
—
• No further action is necessary. C
D
SHIA0011E
Proceed to DIAGNOSTIC PROCE-

DURE 2 that follows (with CON- F
The system is malfunctioning and
SULT-III) or SRC-14, "Trouble
needs to be repaired as indicated.
Diagnosis without CONSULT-III"
(without CONSULT-III).
G
SHIA0012E
SRC
Proceed to COLLISION DIAGNO-
• Air bag is deployed. SIS SRS-17, "For Frontal Collision"
• Seat belt pre-tensioner is deployed. or SRS-18, "For Side and Rollover
Collision". I
• Air bag diagnosis sensor unit is mal-

functioning. J
• Air bag power supply circuit is mal- Refer to SRC-75, ""AIR BAG" Warn-
functioning. ing Lamp Does Not Turn Off".
• SRS air bag warning lamp circuit is
malfunctioning. K
SHIA0013E
• Air bag diagnosis sensor unit is mal-

M
functioning. Refer to SRC-75, ""AIR BAG" Warn-
• Air bag warning lamp circuit is mal- ing Lamp Does Not Turn On".
functioning.
N
SHIA0014E
O
1. Connect CONSULT-III. P
2. Diagnostic code is displayed on "SELF-DIAG [CURRENT]".
If no malfunction is detected on "SELF-DIAG [CURRENT]", but malfunction is detected in "SRS Operation
Check" using the "AIR BAG" warning lamp, the following cases may exist:
• "SELF-DIAG [PAST]" memory might not be erased.
• The SRS system malfunctions intermittently.
Perform DIAGNOSTIC PROCEDURE 4. Refer to SRC-14, "Self-Diagnosis Function (Without CONSULT-
III)".

Trouble Diagnosis without CONSULT-III INFOID:0000000003070629
Inspect SRS Malfunction Using "AIR BAG" Warning Lamp—Diagnosis Mode
NOTE:
SRS will not enter Diagnosis mode if no malfunction is detected in User mode.
1. Turn ignition switch ON.
2. After “AIR BAG” warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
3. Wait more than 3 seconds.
4. Repeat steps 1 to 3 two more times (3 times total).
5. Turn ignition switch ON.
SRS is now in Diagnosis mode. Refer to SRC-71, "Trouble Diagnosis without CONSULT-III".
CONSULT-III Function (AIR BAG) INFOID:0000000003070630
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
AIR BAG diagnostic mode Description

A current Self-diagnosis result (also indicated by the number of warning lamp flashes in the Diagnosis
SELF-DIAG [CURRENT] mode) is displayed on the CONSULT-III screen in real time. This refers to a malfunctioning part requir-
ing repairs.
Diagnosis results previously stored in the memory are displayed on the CONSULT-III screen. The
SELF-DIAG [PAST]
stored results will remain until memory erasing is executed.
With TROUBLE DIAG RECORD, diagnosis results previously erased by a reset operation can be dis-
TROUBLE DIAG RECORD
played on the CONSULT-III screen.
The air bag diagnosis sensor unit for each vehicle model is assigned with its own, individual classifica-
tion number. This number will be displayed on the CONSULT-III screen, as shown. When replacing the
air bag diagnosis sensor unit, refer to the part number for the compatibility. After installation, replace-
ECU DISCRIMINATED NO.
ment with a correct unit can be checked by confirming this classification number on the CONSULT-III
screen.
The air bag diagnosis sensor unit discriminated number assigned is F669.
The STATUS (readiness) of the front passenger air bag module is displayed. The STATUS displayed
(ON/OFF) depends on the signals supplied to the occupant classification system control unit and air
PASSENGER AIR BAG
bag diagnosis sensor unit. Refer to SRC-10, "Occupant Classification System (OCS)" for more infor-
mation.
Self-Diagnosis Function (Without CONSULT-III) INFOID:0000000003070631
• The reading of these results is accomplished using one of two modes —“User mode” and “Diagnosis mode”.
• After a malfunction is repaired, turn the ignition switch OFF for at least one second, then back ON. Diagnosis
mode returns to the User mode. At that time, the self-diagnostic result is cleared.

HOW TO CHANGE SELF-DIAGNOSIS MODE
A
SHIA0183E F
Final Check of SRS Using CONSULT-III—Diagnosis Mode G
1. Connect CONSULT-III.
2. If no DTC is detected on “SELF-DIAG [CURRENT]”, repair of SRS is completed. Go to step 3.
If any DTC is detected on “SELF-DIAG [CURRENT]”, the malfunctioning part has not been repaired com- SRC
pletely or another malfunctioning part is being detected. Perform DIAGNOSTIC PROCEDURE 2. Refer to
SRC-12, "SRS Operation Check".
3. Touch “ERASE”. I
NOTE:
Touch “ERASE” to clear the memory of the malfunction (“SELF-DIAG [PAST]”).
If the memory of the malfunction in “SELF-DIAG [PAST]” is not erased, the User mode shows the system J
malfunction by the operation of the warning lamp even if the malfunction is repaired completely.
4. Touch “BACK” key of CONSULT-III. Touch “SELF-DIAG [PAST]”.
5. Check that no malfunction is detected on “SELF-DIAG [PAST]”. K
6. Touch “BACK” key of CONSULT-III to return to User mode from Diagnosis mode.
7. Turn ignition switch OFF and then turn off and disconnect CONSULT-III.
8. Go to SRC-12, "SRS Operation Check". L
Check SRS Repair History M
1.CONSIDER POSSIBILITY THAT SELF-DIAGNOSTIC RESULT WAS NOT ERASED AFTER REPAIR
Check repair history of the SRS. N
Have any previous repairs been made to the SRS?
Yes >> Self-diagnostic result “SELF-DIAG [PAST]” (previously stored in the memory) might not be erased
after repair. Perform DIAGNOSTIC PROCEDURE 3. Refer to SRC-14, "Self-Diagnosis Function O
(Without CONSULT-III)".
No >> Perform DIAGNOSTIC PROCEDURE 2. Refer to SRC-12, "SRS Operation Check".
P

B1049 – B1052, B1054 – B1057 DRIVER AIRBAG MODULE
< COMPONENT DIAGNOSIS >
COMPONENT DIAGNOSIS
Description INFOID:0000000003070632
DTC B1049 – B1052, B1054 – B1057 DRIVER AIRBAG MODULE

The driver air bag module is dual stage and wired to the air bag diagnosis sensor unit through the spiral cable.
The air bag diagnosis sensor unit will monitor for opens and shorts in detected lines to the driver air bag mod-
ule including the spiral cable.
PART LOCATION
DTC Logic INFOID:0000000003070633
DTC DETECTION LOGIC

With CONSULT-lll
CONSULT-III name DTC DTC detecting condition Repair order

Driver air bag module circuit (DR1) is open 1. Visually check the wiring harness connection.
B1049
DRIVER AIRBAG MODULE (including the spiral cable). 2. Replace the harness if it has visible damage.
[OPEN] 3. Replace the driver air bag module.
Driver air bag module circuit (DR2) is open
B1054 4. Replace the spiral cable.
(including the spiral cable).
5. Replace the air bag diagnosis sensor unit.
Driver air bag module circuit (DR1) is 6. Replace the related harness.
B1050 shorted to a power supply circuit
DRIVER AIRBAG MODULE (including the spiral cable).
[VB-SHORT] Driver air bag module circuit (DR2) is
Driver air bag module circuit (DR1) is
B1051 shorted to ground
[GND-SHORT] Driver air bag module circuit (DR2) is
Driver air bag module circuits (DR1) are
B1052 shorted to each other
[SHORT] Driver air bag module circuits (DR2) are
B1057 shorted to each other
Without CONSULT-lll
WHIA0260E
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

1.IGNITION SWITCH A
Turn ignition switch ON.
>> GO TO 2 B
2.CONSULT-III
Select "DIAG MODE".
C
>> GO TO 3
3.DTC D
If DTC is detected. Refer to SRC-17, "Diagnosis Procedure (Component diagnosis)".
E
>> END
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE: F
SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.IGNITION SWITCH
Turn ignition switch ON. G
>> GO TO 2
SRC
2.IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
I
>> GO TO 3
3.WAIT TIME J
Wait more than 3 seconds.
>> GO TO 4 K
4.REPEAT STEPS
Repeat steps 1 to 3 twice. L
>> GO TO 5.
5.IGNITION SWITCH M
N
>> GO TO 6.
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-71, "Trouble Diag- O
nosis without CONSULT-III".
>> END P
Diagnosis Procedure (Component diagnosis) INFOID:0000000003070634
Recheck SRS after each replacement.

1.HARNESS CONNECTOR
Is there any visible damage to the connector?

YES or NO
YES >> Replace the harness.
NO >> GO TO 2
2.WIRING HARNESS
Is there any visible damage to the harness?
YES or NO
NO >> GO TO 3
3.DRIVER AIR BAG MODULE
Replace the driver air bag module. Refer to SRS-4, "Removal and Installation".
>> GO TO 4
4.SPIRAL CABLE
Replace the spiral cable. Refer to SRS-6, "Removal and Installation".
>> GO TO 5
5.AIR BAG DIAGNOSIS SENSOR UNIT
Replace the air bag diagnosis sensor unit. Refer to SRS-14, "Removal and Installation".
>> GO TO 6
6.RELATED HARNESS
Replace the related harness.
>> END

B1065 – B1068, B1070 – B1073 PASSENGER AIRBAG MODULE
A
DTC B1065 – B1068, B1070 – B1073 PASSENGER AIR BAG MODULE B

The passenger air bag module is dual stage and wired to the air bag diagnosis sensor unit. The air bag diag-
nosis sensor unit will monitor for opens and shorts in detected lines to the passenger air bag module.
C
PART LOCATION
D
DTC DETECTION LOGIC

E
With CONSULT-lll

F
Front passenger air bag module circuit 1. Visually check the wiring harness connection.
B1065
ASSIST A/B MODULE (AS1) is open. 2. Replace the harness if it has visible damage.
[OPEN] 3. Replace the front passenger air bag module.
Front passenger air bag module circuit G
B1070 4. Replace the air bag diagnosis sensor unit.
(AS2) is open.
5. Replace the related harness.
Front passenger air bag module circuit
B1066
ASSIST A/B MODULE (AS1) is shorted to a power supply circuit.
SRC
[VB-SHORT] Front passenger air bag module circuit
B1071
(AS2) is shorted to a power supply circuit.
Front passenger air bag module circuit I
B1067
ASSIST A/B MODULE (AS1) is shorted to ground.
[GND-SHORT] Front passenger air bag module circuit
B1072
(AS2) is shorted to ground.
J
Front passenger air bag module circuits
B1068
ASSIST A/B MODULE (AS1) are shorted to each other.
[SHORT] Front passenger air bag module circuits
B1073 K
(AS2) are shorted to each other.
Without CONSULT-lll
L
WHIA0261E
O

P
1.IGNITION SWITCH
>> GO TO 2
2.CONSULT-III
Select "DIAG MODE".
>> GO TO 3
3.DTC
>> END
NOTE:
1.IGNITION SWITCH
>> GO TO 2
2.IGNITION SWITCH
>> GO TO 3
3.WAIT TIME
>> GO TO 4
4.REPEAT STEPS
Repeat steps 1 to 3 twice.
>> GO TO 5
5.IGNITION SWITCH
>> GO TO 6
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-71, "Trouble Diag-
>> END

1.HARNESS CONNECTOR
YES or NO
NO >> GO TO 2
2.WIRING HARNESS
YES or NO

NO >> GO TO 3
3.FRONT PASSENGER AIR BAG MODULE A
Replace the front passenger air bag module. Refer to SRS-8, "Removal and Installation".
B
>> GO TO 4
C
>> GO TO 5 D
5.RELATED HARNESS
E
>> END
SRC

B1134 – B1137 SIDE AIRBAG MODULE LH
DTC B1134 – B1137 FRONT LH SIDE AIR BAG MODULE

The front LH side air bag module is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor
unit will monitor for opens and shorts in detected lines to the front LH side air bag module.
PART LOCATION
DTC DETECTION LOGIC

With CONSULT-lll

SIDE MODULE LH Front LH side air bag module circuit is 1. Visually check the wiring harness connection.
B1134
[OPEN] open. 2. Replace the harness if it has visible damage.
3. Replace the front LH seat back assembly.
SIDE MODULE LH Front LH side air bag module circuit is
[VB-SHORT] shorted to a power supply circuit.
B1136
[GND-SHORT] shorted to ground.
SIDE MODULE LH Front LH side air bag module circuits are
B1137
[SHORT] shorted to each other.
Without CONSULT-lll
WHIA0265E

1.IGNITION SWITCH
>> GO TO 2
2.CONSULT-III
Select "DIAG MODE".
>> GO TO 3
3.DTC
>> END

NOTE: A
1.IGNITION SWITCH
B
>> GO TO 2 C
2.IGNITION SWITCH
D
>> GO TO 3
3.WAIT TIME E
>> GO TO 4 F
4.REPEAT STEPS
Repeat steps 1 to 3 twice. G
>> GO TO 5
5.IGNITION SWITCH SRC

I
>> GO TO 6
6.DIAGNOSTIC MODE
J
K
>> END
L
1.HARNESS CONNECTOR
Is there any visible damage to the connector? M
YES or NO
NO >> GO TO 2 N
2.WIRING HARNESS
Is there any visible damage to the harness? O
YES or NO
NO >> GO TO 3 P
3.FRONT LH SIDE AIR BAG MODULE
Replace the front LH seat back assembly. Refer to SE-19, "Removal and Installation".
>> GO TO 4
>> GO TO 5
5.RELATED HARNESS
>> END

B1129 – B1132 SIDE AIRBAG MODULE RH
A
DTC B1129 – B1132 FRONT RH SIDE AIR BAG MODULE B

The front RH side air bag module is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor
unit will monitor for opens and shorts in detected lines to the front RH side air bag module.
C
PART LOCATION
D
DTC DETECTION LOGIC

E
With CONSULT-lll

F
SIDE MODULE RH Front RH side air bag module circuit is 1. Visually check the wiring harness connection.
B1129
3. Replace the front RH seat back assembly.
SIDE MODULE RH Front RH side air bag module circuit is G
SIDE MODULE RH Front RH side air bag module circuit is
B1131
SRC
SIDE MODULE RH Front RH side air bag module circuits are
B1132
I
Without CONSULT-lll
WHIA0264E
DTC CONFIRMATION PROCEDURE (With CONSULT-lll) M
1.IGNITION SWITCH
Turn ignition switch ON. N
>> GO TO 2
O
2.CONSULT-III
Select "DIAG MODE".
P
>> GO TO 3
3.DTC
>> END

NOTE:
1.IGNITION SWITCH
>> GO TO 2
2.IGNITION SWITCH
>> GO TO 3
3.WAIT TIME
>> GO TO 4
4.REPEAT STEPS
>> GO TO 5
5.IGNITION SWITCH
>> GO TO 6
6.DIAGNOSTIC MODE
>> END

1.HARNESS CONNECTOR
YES or NO
NO >> GO TO 2
2.WIRING HARNESS
YES or NO
NO >> GO TO 3
3.FRONT RH SIDE AIR BAG MODULE
Replace the front RH seat back assembly. Refer to SE-19, "Removal and Installation".
>> GO TO 4
A
>> GO TO 5
5.RELATED HARNESS B
>> END C
SRC

B1150 – B1153 SIDE CURTAIN AIR BAG MODULE LH
DTC B1150 – B1153 LH SIDE CURTAIN AIR BAG MODULE

The LH side curtain air bag module is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor
unit will monitor for opens and shorts in detected lines to the LH side curtain air bag module.
PART LOCATION
DTC DETECTION LOGIC

With CONSULT-lll

CURTAIN MODULE LH LH side curtain air bag module circuit is 1. Visually check the wiring harness connection.
B1150
3. Replace the LH side curtain air bag module.
CURTAIN MODULE LH LH side curtain air bag module circuit is
B1152
CURTAIN MODULE LH LH side curtain air bag module circuits are
B1153
Without CONSULT-lll
WHIA0267E

1.IGNITION SWITCH
>> GO TO 2
2.CONSULT-III
Select "DIAG MODE".
>> GO TO 3
3.DTC
>> END

NOTE: A
1.IGNITION SWITCH
B
>> GO TO 2 C
2.IGNITION SWITCH
D
>> GO TO 3
3.WAIT TIME E
>> GO TO 4 F
4.REPEAT STEPS
>> GO TO 5

I
>> GO TO 6
6.DIAGNOSTIC MODE
J
K
>> END
L
1.HARNESS CONNECTOR
YES or NO
NO >> GO TO 2 N
2.WIRING HARNESS
YES or NO
NO >> GO TO 3 P
3.LH SIDE CURTAIN AIR BAG MODULE
Replace the LH side curtain air bag module. Refer to SRS-10, "Removal and Installation".
>> GO TO 4
Replace the air bag diagnosis sensor unit. SRS-14, "Removal and Installation".
>> GO TO 5
5.RELATED HARNESS
>> END

B1145 – B1148 SIDE CURTAIN AIR BAG MODULE RH
A
DTC B1145 – B1148 RH SIDE CURTAIN AIR BAG MODULE B

The RH side curtain air bag module is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor
unit will monitor for opens and shorts in detected lines to the RH side curtain air bag module.
C
PART LOCATION
D
DTC DETECTION LOGIC

E
With CONSULT-lll

F
CURTAIN MODULE RH RH side curtain air bag module circuit is 1. Visually check the wiring harness connection.
B1145
3. Replace the RH side curtain air bag module.
CURTAIN MODULE RH RH side curtain air bag module circuit is G
CURTAIN MODULE RH RH side curtain air bag module circuit is
B1147
SRC
CURTAIN MODULE RH RH side curtain air bag module circuits are
B1148
I
Without CONSULT-lll
WHIA0266E
1.IGNITION SWITCH
>> GO TO 2
O
2.CONSULT-III
Select "DIAG MODE".
P
>> GO TO 3
3.DTC
>> END

NOTE:
1.IGNITION SWITCH
>> GO TO 2
2.IGNITION SWITCH
>> GO TO 3
3.WAIT TIME
>> GO TO 4
4.REPEAT STEPS
>> GO TO 5
5.IGNITION SWITCH
>> GO TO 6
6.DIAGNOSTIC MODE
>> END

1.HARNESS CONNECTOR
YES or NO
NO >> GO TO 2
2.WIRING HARNESS
YES or NO
NO >> GO TO 3
3.RH SIDE CURTAIN AIR BAG MODULE
Replace the RH side curtain air bag module. Refer to SRS-10, "Removal and Installation".
>> GO TO 4
A
>> GO TO 5
5.RELATED HARNESS B
>> END C
SRC

B1086 – B1089 SEAT BELT PRE-TENSIONER LH
DTC B1086 – B1089 SEAT BELT PRE-TENSIONER LH

The seat belt pre-tensioner LH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit
will monitor for opens and shorts in detected lines to the seat belt pre-tensioner LH.
PART LOCATION
DTC DETECTION LOGIC

With CONSULT-lll

PRE-TEN FRONT LH LH seat belt pre-tensioner circuit is open. 1. Visually check the wiring harness connection.
B1086
[OPEN] 2. Replace the harness if it has visible damage.
3. Replace the front LH seat belt pre-tensioner.
PRE-TEN FRONT LH LH seat belt pre-tensioner circuit is shorted
[VB-SHORT] to a power supply circuit.
PRE-TEN FRONT LH LH seat belt pre-tensioner circuit is shorted
B1088
[GND-SHORT] to ground.
PRE-TEN FRONT LH LH seat belt pre-tensioner circuits are
B1089
Without CONSULT-lll
WHIA0263E

1.IGNITION SWITCH
>> GO TO 2
2.CONSULT-III
Select "DIAG MODE".
>> GO TO 3
3.DTC
>> END

NOTE: A
1.IGNITION SWITCH
B
>> GO TO 2 C
2.IGNITION SWITCH
D
>> GO TO 3
3.WAIT TIME E
>> GO TO 4 F
4.REPEAT STEPS
>> GO TO 5

I
>> GO TO 6
6.DIAGNOSTIC MODE
J
K
>> END
L
1.HARNESS CONNECTOR
YES or NO
NO >> GO TO 2 N
2.WIRING HARNESS
YES or NO
NO >> GO TO 3 P
3.FRONT LH SEAT BELT PRE-TENSIONER
Replace the front LH seat belt pre-tensioner. Refer to SB-6, "SEAT BELT RETRACTOR : Removal and Instal-
lation".
>> GO TO 4

>> GO TO 5
5.RELATED HARNESS
>> END

B1081 – B1084 SEAT BELT PRE-TENSIONER RH
A
DTC B1081 – B1084 SEAT BELT PRE-TENSIONER RH B

The seat belt pre-tensioner RH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit
will monitor for opens and shorts in detected lines to the seat belt pre-tensioner RH.
C
PART LOCATION
D
DTC DETECTION LOGIC

E
With CONSULT-lll

F
PRE-TEN FRONT RH RH seat belt pre-tensioner circuit is open. 1. Visually check the wiring harness connection.
B1081
[OPEN] 2. Replace the harness if it has visible damage.
3. Replace the front RH seat belt pre-tensioner.
PRE-TEN FRONT RH RH seat belt pre-tensioner circuit is short- G
[VB-SHORT] ed to a power supply circuit.
PRE-TEN FRONT RH RH seat belt pre-tensioner circuit is short-
B1083
[GND-SHORT] ed to ground.
SRC
PRE-TEN FRONT RH RH seat belt pre-tensioner circuits are
B1084
I
Without CONSULT-lll
WHIA0262E
1.IGNITION SWITCH
>> GO TO 2
O
2.CONSULT-III
Select "DIAG MODE".
P
>> GO TO 3
3.DTC
>> END

NOTE:
1.IGNITION SWITCH
>> GO TO 2
2.IGNITION SWITCH
>> GO TO 3
3.WAIT TIME
>> GO TO 4
4.REPEAT STEPS
>> GO TO 5
5.IGNITION SWITCH
>> GO TO 6
6.DIAGNOSTIC MODE
>> END

1.HARNESS CONNECTOR
YES or NO
NO >> GO TO 2
2.WIRING HARNESS
YES or NO
NO >> GO TO 3
3.FRONT RH SEAT BELT PRE-TENSIONER
Replace the front RH seat belt pre-tensioner. Refer to SB-6, "SEAT BELT RETRACTOR : Removal and Instal-
lation".
>> GO TO 4

4.AIR BAG DIAGNOSIS SENSOR UNIT A
>> GO TO 5 B
5.RELATED HARNESS
C
>> END
D
SRC

B1033 – B1035 CRASH ZONE SENSOR
DTC B1033 – B1035 CRASH ZONE SENSOR

The crash zone sensor is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will
monitor for opens and shorts in detected lines to the crash zone sensor.
PART LOCATION
DTC DETECTION LOGIC

With CONSULT-lll
CRASH ZONE SEN B1033 Crash zone sensor has malfunctioned. 1. Visually check the wiring harness connection.
[UNIT FAIL] 2. Replace the harness if it has visible damage.
B1034
3. Replace the crash zone sensor.
CRASH ZONE SEN Crash zone sensor communication error. 4. Replace the air bag diagnosis sensor unit.
B1035
[COMM FAIL] 5. Replace the related harness.
Without CONSULT-lll
WHIA0200E

1.IGNITION SWITCH
>> GO TO 2
2.CONSULT-III
Select "DIAG MODE".
>> GO TO 3
3.DTC
>> END
NOTE:

1.IGNITION SWITCH A
>> GO TO 2 B
2.IGNITION SWITCH
C
>> GO TO 3
3.WAIT TIME D
E
>> GO TO 4
4.REPEAT STEPS
Repeat steps 1 to 3 twice. F
>> GO TO 5
G
5.IGNITION SWITCH
SRC
>> GO TO 6
6.DIAGNOSTIC MODE I
J
>> END
K
1.HARNESS CONNECTOR
L
YES or NO
YES >> Replace the harness. M
NO >> GO TO 2
2.WIRING HARNESS
Is there any visible damage to the harness? N
YES or NO
NO >> GO TO 3 O
3.CRASH ZONE SENSOR
Replace the crash zone sensor. Refer to SRS-12, "Removal and Installation". P
>> GO TO 4

>> GO TO 5
5.RELATED HARNESS
>> END

B1118 – B1120 SATELLITE SENSOR LH
A
DTC B1118 – B1120 SATELLITE SENSOR LH B

The satellite sensor LH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will
monitor the satellite sensor LH for internal failures and it's circuits for communication errors.
C
PART LOCATION
D
DTC DETECTION LOGIC

E
With CONSULT-lll

F
SATELLITE SENS LH B1118 LH side air bag satellite sensor has mal- 1. Visually check the wiring harness connection.
[UNIT FAIL] functioned. 2. Replace the harness if it has visible damage.
B1119
3. Replace the LH side air bag satellite sensor.
SATELLITE SENS LH LH side air bag satellite sensor communi- 4. Replace the air bag diagnosis sensor unit. G
B1120
[COMM FAIL] cation error. 5. Replace the related harness.
Without CONSULT-lll SRC
K
WHIA0204E
DTC CONFIRMATION PROCEDURE (With CONSULT-lll) L

1.IGNITION SWITCH
M
>> GO TO 2
2.CONSULT-III N
Select "DIAG MODE".
O
>> GO TO 3
3.DTC
If DTC is detected. Refer to SRC-44, "Diagnosis Procedure (Component diagnosis)". P
>> END
NOTE:

1.IGNITION SWITCH
>> GO TO 2
2.IGNITION SWITCH
>> GO TO 3
3.WAIT TIME
>> GO TO 4
4.REPEAT STEPS
>> GO TO 5
5.IGNITION SWITCH
>> GO TO 6
6.DIAGNOSTIC MODE
>> END

1.HARNESS CONNECTOR
YES or NO
NO >> GO TO 2
2.WIRING HARNESS
YES or NO
NO >> GO TO 3
3.LH SIDE AIR BAG SATELLITE SENSOR
Replace the LH side air bag satellite sensor. Refer to SRS-13, "Removal and Installation".
>> GO TO 4

>> GO TO 5
5.RELATED HARNESS A

B
>> END
SRC

B1113 – B1115 SATELLITE SENSOR RH
DTC B1113 – B1115 SATELLITE SENSOR RH

The satellite sensor RH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will
monitor the satellite sensor RH for internal failures and it's circuits for communication errors.
PART LOCATION
DTC DETECTION LOGIC

With CONSULT-lll
SATELLITE SENS RH B1113 RH side air bag satellite sensor has mal- 1. Visually check the wiring harness connection.
B1114
3. Replace the RH side air bag satellite sensor.
SATELLITE SENS RH RH side air bag satellite sensor communi- 4. Replace the air bag diagnosis sensor unit.
B1115
[COMM FAIL] cation error. 5. Replace the related harness.
Without CONSULT-lll
WHIA0203E

1.IGNITION SWITCH
>> GO TO 2
2.CONSULT-III
Select "DIAG MODE".
>> GO TO 3
3.DTC
>> END
NOTE:

1.IGNITION SWITCH A
>> GO TO 2 B
2.IGNITION SWITCH
C
>> GO TO 3
3.WAIT TIME D
E
>> GO TO 4
4.REPEAT STEPS
>> GO TO 5
G
5.IGNITION SWITCH
SRC
>> GO TO 6
6.DIAGNOSTIC MODE I
J
>> END
K
1.HARNESS CONNECTOR
L
YES or NO
NO >> GO TO 2
2.WIRING HARNESS
YES or NO
NO >> GO TO 3 O
3.RH SIDE AIR BAG SATELLITE SENSOR
Replace the RH side air bag satellite sensor. Refer to SRS-13, "Removal and Installation". P
>> GO TO 4

>> GO TO 5
5.RELATED HARNESS
>> END

B1XXX AIR BAG DIAGNOSIS SENSOR UNIT
A
DTC B1XXX AIR BAG DIAGNOSIS SENSOR UNIT B

The air bag diagnosis sensor unit will run self diagnostics when the ignition switch is turned ON. It has the
potential to set many diagnostic trouble codes which will conform to the B1XXX format, but will not match any
other SRS diagnostic trouble codes. Refer to SRC-68, "Trouble Diagnosis with CONSULT-III". C
PART LOCATION
Refer to SRC-7, "SRS Component Parts Location". D
DTC DETECTION LOGIC E
With CONSULT-lll
F
Air bag diagnosis sensor unit is malfunc- 1. Visually check the wiring harness connection.
tioning. 2. Replace the harness if it has visible damage.
CONTROL UNIT B1XXX G
Without CONSULT-lll SRC
K
WHIA0198E
DTC CONFIRMATION PROCEDURE (With CONSULT-lll) L

1.IGNITION SWITCH
Turn ignition switch ON. M
>> GO TO 2
2.CONSULT-III N
Select "DIAG MODE".
O
>> GO TO 3
3.DTC
If DTC is detected. Refer to SRC-50, "Diagnosis Procedure (Component diagnosis)". P
>> END
NOTE:

1.IGNITION SWITCH
>> GO TO 2
2.IGNITION SWITCH
>> GO TO 3
3.WAIT TIME
>> GO TO 4
4.REPEAT STEPS
>> GO TO 5
5.IGNITION SWITCH
>> GO TO 6
6.DIAGNOSTIC MODE
>> END

1.HARNESS CONNECTOR
YES or NO
NO >> GO TO 2
2.WIRING HARNESS
YES or NO
NO >> GO TO 3
>> GO TO 4
4.RELATED HARNESS

>> END
A
SRC

B1023 PASSENGER AIR BAG OFF INDICATOR
DTC B1023 FRONT PASSENGER AIR BAG OFF INDICATOR

The front passenger air bag off indicator is wired to the air bag diagnosis sensor unit. The air bag diagnosis
sensor unit monitors the front passenger air bag off indicator and circuit for failures.
PART LOCATION
DTC DETECTION LOGIC

With CONSULT-lll

Front passenger air bag off indicator is 1. Visually check the wiring harness connection.
malfunctioning. 2. Replace the harness if it has visible damage.
3. Replace the front passenger air bag off indi-
PASS A/B INDCTR CKT B1023
cator.
Without CONSULT-lll
WHIA0212E

1.IGNITION SWITCH
>> GO TO 2
2.CONSULT-III
Select "DIAG MODE".
>> GO TO 3
3.DTC
>> END
NOTE:

1.IGNITION SWITCH A
>> GO TO 2 B
2.IGNITION SWITCH
C
>> GO TO 3
3.WAIT TIME D
E
>> GO TO 4
4.REPEAT STEPS
>> GO TO 5
G
5.IGNITION SWITCH
SRC
>> GO TO 6
6.DIAGNOSTIC MODE I
J
>> END
K
1.HARNESS CONNECTOR
L
YES or NO
NO >> GO TO 2
2.WIRING HARNESS
YES or NO
NO >> GO TO 3 O
3.FRONT PASSENGER AIR BAG OFF INDICATOR
Replace the front passenger air bag off indicator. IP-11, "Removal and Installation". P
>> GO TO 4

>> GO TO 5
5.RELATED HARNESS
>> END

B1017, B1018, B1020 – B1022 OCCUPANT CLASSIFICATION SYSTEM
A
DTC B1017 – B1022 OCCUPANT CLASSIFICATION SYSTEM (OCS) B

The occupant classification system control unit is wired to the air bag diagnosis sensor unit. The air bag diag-
nosis sensor unit will monitor the occupant classification system for control unit and sensor mat failures and
interuptions in communication between the OCS control unit and the air bag diagnosis sensor unit. C
PART LOCATION
Refer to SRC-7, "SRS Component Parts Location". D
DTC DETECTION LOGIC E
With CONSULT-lll
F
B1017 The OCS control unit is malfunctioning. 1. Replace the RH front seat cushion assembly.
OCCUPANT SENS C/U Do not disassemble the seat cushion assem-
B1020 G
[UNIT FAIL] bly.
B1021
OCCUPANT SENS The OCS sensor mat is malfunctioning.
B1018
[UNIT FAIL] SRC
OCCUPANT SENS The OCS is malfunctioning.
B1019
[OTHER FAIL]
Communication between the OCS control 1. Visually check the wiring harness connection. I
unit and the air bag diagnosis sensor unit is 2. Replace the harness if it has visible damage.
OCCUPANT SENS C/U interrupted. 3. Replace the RH front seat cushion assembly.
B1022
[COMM FAIL] Do not disassemble the seat cushion assem-
bly.
J
Without CONSULT-lll K
N
WHIA0211E
DTC CONFIRMATION PROCEDURE (With CONSULT-lll) O

1.IGNITION SWITCH
P
>> GO TO 2
2.CONSULT-III
Select "DIAG MODE".
>> GO TO 3
3.DTC
>> END
NOTE:
1.IGNITION SWITCH
>> GO TO 2
2.IGNITION SWITCH
>> GO TO 3
3.WAIT TIME
>> GO TO 4
4.REPEAT STEPS
>> GO TO 5
5.IGNITION SWITCH
>> GO TO 6
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-7, "SRS Compo-
nent Parts Location".
>> END

1.DTC
Does CONSULT-III indicate B1022?
YES or NO
YES >> GO TO 2
NO >> GO TO 4
2.HARNESS CONNECTOR
YES or NO
NO >> GO TO 3

3.WIRING HARNESS A
YES or NO
YES >> Replace the harness. B
NO >> GO TO 4
4.RH FRONT SEAT CUSHION ASSEMBLY
C
Replace the RH front seat cushion assembly. Refer to SE-19, "Removal and Installation".
>> GO TO 5 D
E
>> END.
SRC

B1209 – B1210 COLLISION DETECTION
B1209 – B1210 COLLISION DETECTION
DTC B1209 - B1210 COLLISION DETECTION

The air bag diagnosis sensor unit will set this DTC if it has detected a collision which has resulted in a frontal
or side deployment of one or more air bags or pre-tensioners. If this DTC is detected after a SRS repair, the
air bag diagnosis sensor unit has not yet been replaced. This DTC can not be erased. If the air bag diagnosis
sensor unit detects a frontal collision, it will send an air bag deployment signal to the high voltage ECU. The
high voltage ECU will then shut down the entire high voltage power supply.
PART LOCATION
DTC DETECTION LOGIC

With CONSULT-lll

FRONTAL COLLISION Driver and/or front passenger air bag mod- Refer to SRS-17, "For Frontal Collision".
B1209
DETECTION ules are deployed.
SIDE COLLISION DE- Side and/or curtain air bag modules are Refer to SRS-18, "For Side and Rollover Collision".
B1210
TECTION deployed.

1.IGNITION SWITCH
>> GO TO 2
2.CONSULT-III
Select "DIAG MODE".
>> GO TO 3
3.DTC
>> END
Refer to SRS-17, "For Frontal Collision" or SRS-18, "For Side and Rollover Collision".

DIAGNOSIS SENSOR UNIT
< ECU DIAGNOSIS >
ECU DIAGNOSIS A
Wiring Diagram INFOID:0000000003070677
B
SRC
AWHWA0023GB

< ECU DIAGNOSIS >
AWHWA0024GB

< ECU DIAGNOSIS >
SRC
AWHIA0091GB

< ECU DIAGNOSIS >
AWHIA0092GB

< ECU DIAGNOSIS >
SRC
AWHIA0093GB

< ECU DIAGNOSIS >
AWHIA0094GB

< ECU DIAGNOSIS >
SRC
AWHIA0095GB

< ECU DIAGNOSIS >
ALHIA0038GB

< ECU DIAGNOSIS >
SRC
AWHIA0054GB

< ECU DIAGNOSIS >
ALHIA0040GB
Trouble Diagnosis with CONSULT-III INFOID:0000000003070678
DIAGNOSTIC CODE CHART

NOTE:
Follow the procedures in numerical order when repairing malfunctioning parts. Confirm whether malfunction is
eliminated using air bag warning lamp or CONSULT-III each time repair is finished. If malfunction is still
observed, proceed to the next step. When malfunction is eliminated, further repair work is not required.

< ECU DIAGNOSIS >
CONSULT-III name DTC DTC detecting condition Repair order A

Driver air bag module circuit (DR1) is 1. Visually check the wiring harness connection.
B1049 open 2. Replace the harness if it has visible damage.
DRIVER AIRBAG MODULE (including the spiral cable). 3. Replace the driver air bag module.
B
[OPEN] 4. Replace the spiral cable.
B1054 open
C
[VB-SHORT] Driver air bag module circuit (DR2) is D
Driver air bag module circuit (DR1) is E
[GND-SHORT] Driver air bag module circuit (DR2) is F
Driver air bag module circuits (DR1) are
B1052 shorted to each other G
[SHORT] Driver air bag module circuits (DR2) are
B1057 shorted to each other SRC
Front passenger air bag module circuit 1. Visually check the wiring harness connection.
B1065
ASSIST A/B MODULE (AS1) is open. 2. Replace the harness if it has visible damage. I
[OPEN] 3. Replace the front passenger air bag module.
(AS2) is open.
Front passenger air bag module circuit J
B1066 (AS1) is shorted to a power supply cir-
ASSIST A/B MODULE cuit.
[VB-SHORT] Front passenger air bag module circuit K
B1071 (AS2) is shorted to a power supply cir-
cuit.
B1067
L
ASSIST A/B MODULE
[GND-SHORT] Front passenger air bag module circuit
B1072
M
Front passenger air bag module circuits
B1068
ASSIST A/B MODULE (AS1) are shorted to each other.
[SHORT] Front passenger air bag module circuits
B1073 N
(AS2) are shorted to each other.
SIDE MODULE LH Front LH side air bag module circuit is 1. Visually check the wiring harness connection.
B1134
3. Replace the front LH seat back assembly. O
B1136
[GND-SHORT] shorted to ground. P
SIDE MODULE LH Front LH side air bag module circuits are
B1137

< ECU DIAGNOSIS >
SIDE MODULE RH Front RH side air bag module circuit is 1. Visually check the wiring harness connection.
B1129
3. Replace the front RH seat back assembly.
B1131
SIDE MODULE RH Front RH side air bag module circuits
B1132
[SHORT] are shorted to each other.
CURTAIN MODULE LH LH side curtain air bag module circuit is 1. Visually check the wiring harness connection.
B1150
3. Replace the LH side curtain air bag module.
B1152
CURTAIN MODULE LH LH side curtain air bag module circuits
B1153
CURTAIN MODULE RH RH side curtain air bag module circuit is 1. Visually check the wiring harness connection.
B1145
3. Replace the RH side curtain air bag module.
B1147
CURTAIN MODULE RH RH side curtain air bag module circuits
B1148
PRE-TEN FRONT LH LH seat belt pre-tensioner circuit is 1. Visually check the wiring harness connection.
B1086
3. Replace the front LH seat belt pre-tensioner.
PRE-TEN FRONT LH LH seat belt pre-tensioner circuit is
PRE-TEN FRONT LH LH seat belt pre-tensioner circuit is
B1088
PRE-TEN FRONT LH LH seat belt pre-tensioner circuits are
B1089
PRE-TEN FRONT RH RH seat belt pre-tensioner circuit is 1. Visually check the wiring harness connection.
B1081
3. Replace the front RH seat belt pre-tensioner.
PRE-TEN FRONT RH RH seat belt pre-tensioner circuit is
PRE-TEN FRONT RH RH seat belt pre-tensioner circuit is
B1083
PRE-TEN FRONT RH RH seat belt pre-tensioner circuits are
B1084
CRASH ZONE SEN B1033 Crash zone sensor has malfunctioned. 1. Visually check the wiring harness connection.
[UNIT FAIL] 2. Replace the harness if it has visible damage.
B1034
3. Replace the crash zone sensor.
CRASH ZONE SEN Crash zone sensor communication er- 4. Replace the air bag diagnosis sensor unit.
B1035
[COMM FAIL] ror. 5. Replace the related harness.
SATELLITE SENS LH B1118 LH side air bag satellite sensor has mal- 1. Visually check the wiring harness connection.
B1119
3. Replace the LH side air bag satellite sensor.
SATELLITE SENS LH LH side air bag satellite sensor commu- 4. Replace the air bag diagnosis sensor unit.
B1120
[COMM FAIL] nication error. 5. Replace the related harness.
SATELLITE SENS RH B1113 RH side air bag satellite sensor has mal- 1. Visually check the wiring harness connection.
B1114
3. Replace the RH side air bag satellite sensor.
SATELLITE SENS RH RH side air bag satellite sensor commu- 4. Replace the air bag diagnosis sensor unit.
B1115
[COMM FAIL] nication error. 5. Replace the related harness.

< ECU DIAGNOSIS >
A
Air bag diagnosis sensor unit is malfunc- 1. Visually check the wiring harness connection.
tioning. 2. Replace the harness if it has visible damage.
CONTROL UNIT B1XXX
4. Replace the related harness. B
Front passenger air bag OFF indicator is 1. Visually check the wiring harness connection.
malfunctioning. 2. Replace the harness if it has visible damage.
3. Replace the front passenger air bag OFF in-
PASS A/B INDCTR CKT B1023
dicator.
C
B1017 The OCS control unit is malfunctioning. 1. Replace the RH front seat cushion assembly. D
OCCUPANT SENS C/U Do not disassemble the seat cushion assem-
B1020
[UNIT FAIL] bly.
B1021
E
OCCUPANT SENS The OCS sensor mat is malfunctioning.
B1018
[UNIT FAIL]
OCCUPANT SENS The OCS is malfunctioning.
[OTHER FAIL]
B1019 F
Communication between the OCS con- 1. Visually check the wiring harness connection.
trol unit and the air bag diagnosis sensor 2. Replace the harness if it has visible damage.
OCCUPANT SENS C/U unit is interrupted. 3. Replace the RH front seat cushion assembly. G
B1022
[COMM FAIL] Do not disassemble the seat cushion assem-
bly.
SRC
FRONTAL COLLISION DE- Driver and/or front passenger air bag Refer to SRS-17, "For Frontal Collision".
B1209
TECTION modules are deployed.
SIDE COLLISION DETEC- Side and/or curtain air bag modules are Refer to SRS-18, "For Side and Rollover Collision".
B1210 I
TION deployed.
Trouble Diagnosis without CONSULT-III INFOID:0000000003070679
J
WARNING LAMP FLASH CODE CHART
NOTE:
Follow the procedures in numerical order when repairing malfunctioning parts. Confirm whether malfunction is K
eliminated using air bag warning lamp each time repair is finished. If malfunction is still observed, proceed to
the next step. When malfunction is eliminated, further repair work is not required.
L
SHIA0026E
O
WHIA0260E

< ECU DIAGNOSIS >
WHIA0198E
WHIA0261E
WHIA0200E
WHIA0262E
WHIA0263E

< ECU DIAGNOSIS >
C
WHIA0203E
WHIA0204E
G
SRC
J
WHIA0264E
WHIA0265E
WHIA0266E

< ECU DIAGNOSIS >
WHIA0267E
WHIA0211E
WHIA0212E

SRS AIR BAG SYSTEM
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS A
SRS AIR BAG SYSTEM
"AIR BAG" Warning Lamp Does Not Turn Off INFOID:0000000003070680
B
1.CHECK CONDITION OF AIR BAG MODULE C
Inspect for any deployed air bag modules or seat belt pre-tensioners.
Are any air bag modules or seat belt pre-tensioners deployed?
D
YES >> Refer to SRS-17, "For Frontal Collision" or SRS-18, "For Side and Rollover Collision".
NO >> GO TO 2
2.CHECK THE AIR BAG FUSE E
Check 10A fuse [No. 2, located in the fuse block (J/B)].
Is the fuse blown?
Yes >> GO TO 3 F
No >> GO TO 4
3.CHECK AIR BAG FUSE AGAIN G
Replace 10A fuse [No. 2, located in the fuse block (J/B)] and turn ignition switch ON.
Does the fuse blow again?
YES >> Replace harness. SRC
NO >> Inspection End.
4.CHECK AIR BAG DIAGNOSIS SENSOR UNIT
I
Connect CONSULT-III.
Is “AIR BAG” displayed on CONSULT-III?
YES >> GO TO 5 J
NO >> Visually inspect the air bag diagnosis sensor unit harness connections. If the connections are OK,
replace the air bag diagnosis sensor unit. Refer to SRS-14, "Removal and Installation".
5.CHECK HARNESS CONNECTION K
Check for loose connections between the combination meter and the air bag diagnosis sensor unit.
Are there any loose connections?
Yes >> Properly connect the combination meter and air bag diagnosis sensor unit harness connectors. If L
“AIR BAG” warning lamp still does not turn off, replace the wiring harness.
No >> Replace air bag diagnosis sensor unit.
"AIR BAG" Warning Lamp Does Not Turn On INFOID:0000000003070681
M
N
1.CHECK METER FUSE
Check the 10A fuse [No. 4, located in the fuse block (J/B)] .
Is the fuse blown? O
Yes >> GO TO 2
No >> GO TO 3
2.REPLACE METER FUSE AND CHECK AGAIN P
Replace 10A fuse [No. 4, located in the fuse block (J/B)] and turn ignition switch ON.
Does the fuse blow again?
Yes >> Replace harness.
No >> Inspection End.
3.CHECK HARNESS CONNECTIONS BETWEEN AIR BAG DIAGNOSIS SENSOR UNIT AND COMBINA-
SRS AIR BAG SYSTEM
TION METER
Inspect the harness and connectors between the air bag diagnosis sensor unit and the combination meter.
Do the harness or connectors have any visible damage?
Yes >> Replace harness.
No >> GO TO 4
4.CHECK COMBINATION METER
Disconnect the air bag diagnosis sensor unit harness connectors and turn ignition switch ON.
Does “AIR BAG” warning lamp turn on?
Yes >> Replace the air bag diagnosis sensor unit. Refer to SRS-14, "Removal and Installation".
No >> Replace the combination meter. Refer to MWI-135, "Removal and Installation".

A
Seat Belt Warning System Does Not Function INFOID:0000000003070682
1.SEAT BELT WARNING LIGHT B

Does the seat belt warning lamp come ON?
C
YES >> GO TO 2
NO >> • Check 10A fuse [No. 4, located in the fuse block (J/B)].
• Check seat belt buckle switch LH.
• Check harness between combination meter and seat belt buckle switch LH. D
• Check combination meter. Refer to MWI-70, "Fail Safe".
2.SEAT BELT BUCKLE LH
E
Fasten the seat belt buckle LH.
Does the seat belt warning lamp go OFF?
YES >> GO TO 3 F
NO >> • Check seat belt buckle switch LH.
• Check harness between combination meter and seat belt buckle switch LH.
3.OCCUPANT CLASSIFICATION SYSTEM G
Have a helper sit in the passenger seat.
Does the seat belt warning lamp go ON?
YES >> GO TO 4 SRC
NO >> • Check occupant classification system. Refer to SRC-10, "Occupant Classification System
(OCS)".
• Check harness between occupant classification control unit and air bag diagnosis sensor unit. I
4.SEAT BELT BUCKLE RH
Fasten the seat belt buckle RH.
J
Does the seat belt warning lamp go OFF?
YES >> System OK.
NO >> • Check seat belt buckle switch RH.
• Check harness between seat belt buckle switch RH and air bag diagnosis sensor unit. K
• Replace air bag diagnosis sensor unit. Refer to SRS-14, "Removal and Installation".

PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000003070683
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Precaution for SRS "AIR BAG" and "SEAT BELT PRE-TENSIONER" Service
INFOID:0000000003070684
• Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
• Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 min-
utes.
For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-
tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have
passed.
• The air bag diagnosis sensor unit must always be installed with the arrow mark “⇐” pointing toward the front
of the vehicle for proper operation. Also check air bag diagnosis sensor unit for cracks, deformities or rust
before installation and replace as required.
• The spiral cable must be aligned with the neutral position since its rotations are limited. Do not attempt to
turn steering wheel or column after removal of steering gear.
• Handle air bag module carefully. Always place driver and front passenger air bag modules with the pad side
facing upward and seat mounted front side air bag module standing with the stud bolt side facing down.
• Conduct self-diagnosis to check entire SRS for proper function after replacing any components.
• After air bag inflates, the front instrument panel assembly should be replaced if damaged.
Occupant Classification System Precaution INFOID:0000000003070685
Replace occupant classification system control unit and passenger front seat cushion as an assembly.

Srs Airbag Control System: Section

Uploaded by

Copyright:

Available Formats

Srs Airbag Control System: Section

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Srs Airbag Control System: Section

Uploaded by

Copyright:

Available Formats

RESTRAINTS

SRS AIRBAG CONTROL SYSTEM

Revision: August 2007 SRC-1 2008 Altima Hybrid

Revision: August 2007 SRC-2 2008 Altima Hybrid

Revision: August 2007 SRC-3 2008 Altima Hybrid

Revision: August 2007 SRC-4 2008 Altima Hybrid

Revision: August 2007 SRC-5 2008 Altima Hybrid

Revision: August 2007 SRC-6 2008 Altima Hybrid

Driver Air Bag Module INFOID:0000000003070616

Revision: August 2007 SRC-7 2008 Altima Hybrid

Front Side Air Bag INFOID:0000000003070618

Side Curtain Air Bag INFOID:0000000003070619

Front Seat Belt Pre-tensioner with Load Limiter INFOID:0000000003070620

Revision: August 2007 SRC-8 2008 Altima Hybrid

Revision: August 2007 SRC-9 2008 Altima Hybrid

Occupant Classification System (OCS) INFOID:0000000003070623

Seat occupied NOTE ON Deactivated (disabled) OFF

1. Seat cushion foam 2. OCS control unit 3. OCS sensor mat

Revision: August 2007 SRC-10 2008 Altima Hybrid

Passenger Seat Belt Warning System Operation

Refer to SRC-7, "SRS Component Parts Location".

Revision: August 2007 SRC-11 2008 Altima Hybrid

User mode Diagnosis mode Display type

HOW TO PERFORM TROUBLE DIAGNOSES FOR QUICK AND ACCURATE REPAIR

Revision: August 2007 SRC-12 2008 Altima Hybrid

Proceed to DIAGNOSTIC PROCE-

• Air bag diagnosis sensor unit is mal-

• Air bag diagnosis sensor unit is mal-

Revision: August 2007 SRC-13 2008 Altima Hybrid

AIR BAG diagnostic mode Description

Self-Diagnosis Function (Without CONSULT-III) INFOID:0000000003070631

Revision: August 2007 SRC-14 2008 Altima Hybrid

Revision: August 2007 SRC-15 2008 Altima Hybrid

DTC B1049 – B1052, B1054 – B1057 DRIVER AIRBAG MODULE

DTC DETECTION LOGIC

CONSULT-III name DTC DTC detecting condition Repair order

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

Diagnosis Procedure (Component diagnosis) INFOID:0000000003070634

Recheck SRS after each replacement.

Revision: August 2007 SRC-17 2008 Altima Hybrid

Revision: August 2007 SRC-18 2008 Altima Hybrid

DTC B1065 – B1068, B1070 – B1073 PASSENGER AIR BAG MODULE B

DTC DETECTION LOGIC

CONSULT-III name DTC DTC detecting condition Repair order

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

Recheck SRS after each replacement.

Revision: August 2007 SRC-20 2008 Altima Hybrid

Revision: August 2007 SRC-21 2008 Altima Hybrid

DTC B1134 – B1137 FRONT LH SIDE AIR BAG MODULE

DTC DETECTION LOGIC

CONSULT-III name DTC DTC detecting condition Repair order

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

Revision: August 2007 SRC-22 2008 Altima Hybrid

Turn ignition switch ON.

Revision: August 2007 SRC-24 2008 Altima Hybrid

DTC B1129 – B1132 FRONT RH SIDE AIR BAG MODULE B

DTC DETECTION LOGIC

CONSULT-III name DTC DTC detecting condition Repair order