GODREJ PROPERTIES LIMITED

Ref. No.: GPL F HS 02 Date:4/1/2023

Rev.No.: 00 Page01 of 01 PROJECT :- Godrej Meridien

Activity: HANDLING OF PORTABLE ELECTRICAL TOOLS

Risk
Risk
Assessment

Opportunities and action

Assessment
existing

Non-Significant (NS)
existing Control
Control

Legal Yes/No

Legal Yes/No
Significant (S) /
Measure

Ref. of WI/SOP
Measure
Sr.
Activity Hazard Issue (Internal/External) Risk ( Probable Outcome) Existing Control Additional Control Measure Remark
No.

Probability(P)

Probability(P)
Risk(R) : P*S

Risk(R) : P*S
Severity(S)

Severity(S)
1. Damaged cable 1. Daily checkup before start 1. Training and instructions to use
Working with Portable 2. Defective tool Internal (Standards, guidelines and models adopted by the 2. Replacing defective / damaged tools right tool for the right job
1 No P3 S2 M NT No P1 S2 L
Electric Tools 3. Loose organization) 3. Use tools only with 2. Keep tools
components (Wheel, switch) protective handles only in the tool boxes
4. Excess pressure on tool 4. Use of Job regarding PPEs. 3. All electric portable tools
5. Improper handling 1. Incident and bodily injuries 5. All electrical connection routed through inspection carried out through
6. Not use 2. Property Damages either ELCB or RCCB 6. All electric department before using the
of PPE electrical cable proper insulated. work place.
1.Provide guard rails / barricade at the work place. 2. Use PPE
like Full Body Harness, Life Line, Helmets, Fall Arrestor Gear and Safety Shoes etc.
3. Obtain the permit for working at height 1.In-house
above 3 meters. development of
1.All workers required to work at
height above 3 meters should be trained &
tested for Vertigo and certified fit experienced
Internal (Standards, guidelines and models adopted by the for working at height by talent
Person can fall down May sustain sever injuries or prove fatal Yes P3 S4 H T NO P1 S4 M GPL
organization) competent Doctors.
2. Horizontal and vertical W HS
safety net required around the 10 2. Develop
elevated work place. Training
Programs taking
care of site
requirements or
Working with Portable activities.
2 1.Fall Arrestor and Safety Nets, etc. m ust be installed. 2.Provide
Electric Tools at Height adequate working space (minimum 0.6 m). 3.Tie / Weld working
platform with fixed support. 4.Use roof top walk ladder while
working on sloping roofs. 5. Avoid movement on beams. 1.Enclose area below with
6. Keep the work place neat and clean. perimeter warning barricade.
7. Remove the scrap immediately. 8. Do not 2. Never
throw or drop materials or equipm ent from height. 9. All tools to be carried leave unprotected floor openings
1.May hit the scrap / material stacked at the ground or in in a tool kit bag or on working uniform. 10. Remove scrap from the planks.
Internal (Standards, guidelines and models adopted by the leading edges unattended.
Material can fall down between 2. May hit 11. Ensure wearing of helmets by the workers working Yes P2 S4 H S NO P1 S4 M
organization) 3. Provide
the workers working at lower levels and may prove fatal at the lower levels.
warning sign “Men working
above” 4.
No loose/unsecured materials
allowed at height.

Prepared By : HIRA
Team Devendra Kumar /Ramzan mujahid/Mukesh Kumar/Sanjay Kumar/sanjeet /Daud Ali
Reviewed By : Mr.Ravi Kumar Vanak
Project Safety Incharge
Approved By :
Mr.Gaurav Srivastava
GPL Project Manager
Probability (P) Mr.Davendra Kumar Mr. Daud Ali P/S S1 S2 S3 S4
P1= Improbable Contractor Project Manager Contractor Safety Incharge P1 L L M M
P2= Remote P2 L M M H
P3= Possible P3 M M H H
P4= Probable P4 M H H H

Severity (s) H: Hazard must be avoided (or the level of risk reduced significantly and reliable by controls).
S1= Negligible M: Hazard should be avoided (or the level of risk reduced significantly and reliable by controls).
S2= Minor L: Risk to be controlled as far as reasonably practicable.
S3= Sever LEGAL: If activity come under legal implication then need to be considered Non-tolerable.
S4= Extreme T: Tolerable
NT: Non - Tolerable