Intelligent Earthquake System

No.
CP-SP-1376E
Intelligent Earthquake
Sensor
Model SES70
User’s Manual
for
System Design
Thank you for purchasing an Azbil

Corporation product.
This manual contains information for
ensuring the correct use of this product.
It also provides necessary information
for installation, maintenance, and
troubleshooting.
This manual should be read by those who
design and maintain equipment that uses
this product. Be sure to keep this manual
nearby for handy reference.
NOTICE
Be sure that the user receives this manual before the product is used.
Copying or duplicating this user’s manual in part or in whole is forbidden.
The information and specifications in this manual are subject to change
without notice.
Considerable effort has been made to ensure that this manual is free from
inaccuracies and omissions. If you should find an error or omission, please
contact the azbil Group.
In no event is Azbil Corporation liable to anyone for any indirect, special or
consequential damages as a result of using this product.
© 2015–2018 Azbil Corporation. All Rights Reserved.

SES™ is a trademark of Azbil Corporation in Japan.
Conventions Used in This Manual
The safety precautions explained in the following section aim to prevent injury to the operator and
others, and to prevent property damage.
W
ARNING Warnings are indicated when mishandling this product might
result in death or serious injury.
C AUTION Cautions are indicated when mishandling this product might

result in minor injury to the user, or physical damage to the
product.
In describing the product, this manual uses the icons and conventions listed below.
Use caution when handling the product.
The indicated action is prohibited.
Always follow the indicated instructions.
Handling Precautions:
Handling Precautions indicate items that the user should pay attention to when handling
this product.
Notes indicate information that might benefit the user.

Note:
(1), (2), (3): Numbers within parentheses indicate steps in a sequence or parts of an explanation.
This indicates the item or page that the user is requested to refer to.
Label and seal

The following nameplate, label, and seal are attached to this unit.
Rating nameplate Warning label Seal
i
Safety Precautions
Safety precautions are intended to ensure the safe and correct use of this product, to prevent injury to the operator
and others, and to prevent damage to property. Be sure to observe these safety precautions. Please make sure you un-
derstand the safety guidelines before reading the rest of this manual.
The use of this product in a manner not specified by the manufacturer will impair its built-in safety features.
WARNING
For explosion-proof instrumentation, install and wire this unit in accordance with the National
Institute of Industrial Safety's "User's Guidelines for Electrical Installations for Explosive Gas
Atmospheres in General Industry" (Tokyo, 1994 [in Japanese]).
This device is certified as a pressure-resistant explosion-proof construction (Ex d IIC T4). Install
it in a location that complies with this certification.
In Taiwan, this device cannot be used in an explosive atmosphere.
If there might be an explosive atmosphere, do not open the cover. Doing so may cause
explosion or fire.
If you use the Smart Loader Package (sold separately), do so in a non-hazardous area where
there is no danger of explosion or fire.
Always use the cable gland and flameproof packing set supplied with this unit. In addition,
use packing that is appropriate for the cable. If the wrong packing is used, the unit will no
longer be a certified explosion-proof product.
Use cables with a heat resistance to temperatures of 80 °C or more. If a cable with a heat
resistance of less than 80 °C used, the unit will no longer be a certified explosion-proof
product. Moreover, fire or device failure may result.
After wiring work, be sure to firmly tighten the cover screws. Otherwise the unit will not satisfy
the conditions for a pressure-resistant explosion-proof construction.
Before doing wiring work, be sure to disconnect the power. Failure to do so may result in an
electric shock.
If the cover is open in a hazardous area, do not turn on the electricity. Doing so may cause
explosion or fire.
CAUTION
Only specialists with the proper knowledge and technical skill concerning this type of
equipment and this unit should carry out the installation, wiring, inspection, and maintenance
work.
This device does not incorporate any countermeasures against lightning. As necessary, take
appropriate measures to protect equipment from lightning.
Do not use a walkie-talkie or other transceiver within 2 m of this unit or cables connected to
this unit. Doing so may cause this unit to malfunction.
Use shielded cables for wiring.
ii
CAUTION
Be sure to carry out the wiring work properly. Incorrect wiring may cause device failure.
Do not allow crimp terminals (etc.) to come into contact with adjacent terminals. Doing so may
cause fire or device failure.
For control of critical equipment (e.g., for earthquake emergency shutdown), to avoid
dependence on a single output, use this earthquake sensor together with another one, or use
a 2-out-of-3 configuration.
If this unit malfunctions, its electrical output may be incorrect. If equipment safety might
thereby be endangered, consider having a fail-safe design for the system as a whole, with
compartmentalization of controller and limits and with duplexing or use a redundant design.
Interference from a shock wave or electromagnetic wave may activate the noise protection
function of this unit, preventing vibration detection output or AO/DO output.
Handle the case and cover with care. If the threads are damaged, the cover will not open and
close properly.
Do not subject this device to shock that exceeds the operating conditions stated in the
specifications. Doing do so may cause device failure.
This device is a precision instrument. Impact from a 1 cm fall is enough to damage the internal
sensor.
Be sure to handle it carefully. Take care to prevent impact when removing this unit from the
box, placing it on the floor temporarily during installation, etc.
During installation, take care not to bump this device against metal objects such as pipes at
the work site.
When connecting the wiring, be sure not to hit the sensor with a crimping tool, screwdriver, or
other tool.
When tightening the cable gland with a wrench, do not hit the wrench with a hammer.
If there is a risk of impact to this unit after it is mounted, install a protective cover or like.
Do not disassemble or modify this device.
Do not subject this unit to impact or shock from a wrench or the like when removing the unit
for periodic inspection, etc.
When sending this unit back to Azbil Corporation for periodic inspection, pack it in the
shipping package specially made for it. Contact the azbil Group for the shipping box.
Handling Precautions
• Do not remove the seal from the cable gland connection port until the wiring
work is about to begin.
iii
This unit withstands an impact of 490 m/s2 (50 G). Because this device is a precision instrument, handle
it with care. Two metal objects knocking together can create an impact of several tens of thousands of
m/s2 (several thousands of Gs).
Prohibited actions
(1) Dropping the unit on the floor (2) Casually putting the unit down on a table or
stand (put it down gently)
(3) Bumping the unit against pipes, etc. (4) Striking the unit with a tool
(5) Hitting a tool (during installation or wiring) (6) Hitting the tool (to open the cover)
iv
The Role of This Manual
There are four different manuals related to the SES70. Read them as necessary for your specific requirements. If a
manual you require is not available, contact the azbil Group or its dealer.
Intelligent Earthquake Sensor Model SES70 User’s Manual for System Design
Manual No. CP-SP-1376E
This manual.
First-time users of the SES70 and those designing or maintaining hardware that uses the
SES70 should read this manual thoroughly. This manual gives an overview and hardware
specifications, and describes installation, wiring, setup, operation, and troubleshooting.
Intelligent Earthquake Sensor Model SES70 User's Manual

This manual is supplied with the SES70. Personnel in charge of the installation or
wiring of this device, or in charge of the design or maintenance of hardware that
uses this device, should read this manual thoroughly. The manual gives an over-
view of this device and describes installation methods, wiring, startup preparation,
and troubleshooting.
SLP-SE7 Smart Loader Package for SES70 Intelligent Earthquake Sensor

This manual is included on the SLP-SE7 installation disk. After installation, person-
nel in charge of settings or in charge of monitoring the device's operation should
read this manual thoroughly. The SLP-SE7 is used for monitoring and configuration
of the SES70 on a PC. The manual describes installation on a PC, loader functions,
and loader operation.
v
Organization of This User's Manual
This manual is organized as follows.
Chapter 1. OVERVIEW
Features and models
Chapter 2. NAMES AND FUNCTIONS OF PARTS

Names and functions of parts
Chapter 3. INSTALLATION
Installation methods, important notes, and locations
Chapter 4. WIRING
Wiring procedures, connection examples, and precautions for wiring
Chapter 5. PREPARATIONS FOR START-UP

What to check before use and how to set the time
Chapter 6. INTERNAL PROCESSING

Basic operation modes, calculations, control output, waveform recording, and error
diagnosis
Chapter 7. LOADER ACCESS DATA

Data accessed by the SLP-SE7 from a PC (For details on the loader, see
SLP-SE7 Smart Loader Package for SES70 Intelligent Earthquake Sensor, No.
CP-UM-5756E.)
Chapter 8. MAINTENANCE AND TROUBLESHOOTING

Troubleshooting and Countermeasures
Chapter 9. DISPOSAL
Disposal
Chapter 10. SPECIFICATIONS

General specifications, performance specifications, and external dimensions
APPENDIX
Glossary and method of determining acceleration accuracy
vi
Contents
Conventions Used in This Manual
Safety Precautions
The Role of This Manual
Organization of This User's Manual
Chapter 1. OVERVIEW 1-1
Application
1-1
Features
1-2
Model selection
1-3
Chapter 2. NAMES AND FUNCTIONS OF PARTS 2-1
Names of parts
2-1
Basic function block diagram
2-1
Internal structure
2-2
Measurement principles
2-2
Chapter 3. INSTALLATION 3-1
Installation Location
3-1
Installation Instructions
3-1
Chapter 4. WIRING 4-1
Wiring Procedure
4-2
Connecting the battery
4-6
Lightning surge protection
4-6
Chapter 5. PREPARATIONS FOR START-UP 5-1
Procedure for setting the clock

5-1
Chapter 6. INTERNAL PROCESSING 6-1
6-1 Modes 6-1

Mode transition 6-1
Functions of the modes 6-2
6-2 Internal Calculation Processes 6-7
Internal Calculation 6-7
Various calculations and judgment processes 6-8
SI calculation 6-10
Synthesized AC acceleration calculation 6-11
vii
Calculation of the JMA seismic intensity scale equivalent value 6-12
Relationship of the JMA scale (shindo scale), acceleration, SI value, and mea-
sured seismic intensity (shindo) 6-12
Noise protection process 6-12
6-3 Waveform Recording 6-13
Waveform recording header information 6-13
Automatic waveform recording 6-13
Example of maximum value recording without trigger update 6-15
Example of maximum value recording with trigger update 6-17
Example of threshold value recording 6-19
Forced waveform recording 6-21
Example of waveform recording 6-21
6-4 Vibration Detection and Liquefaction Judgment Functions 6-22
Vibration detection judgment function 6-22
Liquefaction judgment function 6-22
6-5 Noise Protection Function 6-24
6-6 Error Diagnosis Functions 6-26
Failure level standards 6-26
Diagnostic functions according to the mode 6-27
Various error diagnosis functions 6-27
6-7 Output Functions 6-29
Output update and hold processes 6-29
Hold process 6-29
Manual output 6-30
Output adjustment (constant drift) 6-31
Output adjustment (high-frequency noise) 6-31
Output selection 6-32
Outputs according to mode 6-33
6-8 Maintenance Sequence 6-34
Maintenance sequence 6-34
6-9 LED Output Functions 6-36
Chapter 7. LOADER ACCESS DATA 7-1
Real-time data monitoring data

7-1
Changing of settings
7-2
Waveform recording
7-6
Manual output function
7-6
Diagnosis and adjustment function
7-8
Chapter 8. MAINTENANCE AND TROUBLESHOOTING 8-1
Checklist for periodic inspection

8-1
How to replace the battery
8-1
Troubleshooting
8-2
viii
Chapter 9. DISPOSAL 9-1
Chapter 10. SPECIFICATIONS 10-1
10-1 Specifications 10-1

10-2 Performance Specifications 10-3
10-3 Other Specifications 10-4
Communication specifications 10-4
External dimensions 10-4
APPENDIX App-1
Glossary
App-1
Method of determining acceleration accuracy
App-2
Relationships between JMA seismic intensity, acceleration, SI value, and mea-

sured JMA seismic intensity App-5
ix
Chapter 1. OVERVIEW
Application
The SES70 Intelligent Earthquake Sensor calculates seismic intensity (SI), which
represents estimated structural damage, and the Japan Meteorological Agency
(JMA) seismic intensity scale (shindo scale) equivalent value, based on acceleration
signals generated from the built-in accelerometer.
Additionally, the unit judges ground liquefaction from the acceleration waveform
characteristics, and outputs the results.
zz Application examples
1. Earthquake emergency shutdown and remote monitoring system
To communications line
SI value/acceleration, etc.
Vibration detection output DCX350 (Azbil Corporation’s

remote data collector)
SES70 Shutoff valve
2. Earthquake monitoring system

Display unit (with application software)
RS-485
SES70 Lamp, etc.
3. Earthquake monitoring with 2-out-of-3 shutdown system

Display unit (with application software)
RS-485
Vibration detection output
Shutoff valve
2-out-of-3 relay circuit
SES70 SES70 SES70
To create a redundant system, take into account the following:

• If electrical noise is expected, keep wiring away from sources of noise.
• ‌If interference from other vibration or shock is expected, install the SES on a foun-
dation separated as far as possible from the source of the vibration or shock.
1-1
Chapter 1. OVERVIEW
Features
The SES70 calculates seismic intensity (SI), which represents estimated structural
damage, and the JMA seismic intensity scale equivalent value, based on accelera-
tion signals generated from the built-in accelerometer, and it can output the results.
Additionally, the unit can judge ground liquefaction from the acceleration wave-
form characteristics, and can output the results.
Other features are shown below:
• Thanks to the 3 axes (north-south, east-west, and up-down = X, Y, Z) of the
servo accelerometer, high-accuracy acceleration measurement is possible by
characterization of the acceleration waveforms.
• Two independent acceleration values are available for different purposes, either
calculation or control. A filter coefficient and the number of axes for synthesized
AC acceleration can be set individually for acceleration values.
• The unit synthesizes acceleration signals as vectors and, based upon the maxi-
mum value within the time window, it calculates the synthesized AC acceleration
for calculation and the synthesized AC acceleration for control. The synthesized
AC acceleration selected for the PV can be output as a 4–20 mA analog signal.
• By vector projection of the AC acceleration for calculation signals in 8 directions
in a horizontal plane, the unit executes a speed response calculation in 8 direc-
tions in real time. The maximum value obtained within the time window is out-
put as the SI value. The SI value can be output as a 4–20 mA analog signal.
• Regarding SI calculation, in addition to speed response calculation in 8 direc-
tions (7 natural periods), calculation in 16 directions (24 natural periods) can be
chosen. The selected SI values are used for the PV, vibration detection judgment,
waveform recording, analog output (AO), etc.
• The JMA shindo earthquake scale is calculated with an approximate formula that
uses the SI value and the synthesized AC acceleration for calculation. The result-
ing JMA seismic intensity scale equivalent value can be output as a 4–20 mA
analog signal.
• The liquefaction detection algorithm, which uses a horizontal 2-axis calculation
AC, detects the occurrence of liquefaction. When it is detected, the liquefaction
detection output turns ON.
• The automatic waveform recording function can record ten 360-second wave-
forms of 3-axis acceleration signals at a 10 ms sampling cycle when triggered by
the synthesized AC acceleration value for calculation, the SI value, or the JMA
seismic intensity scale equivalent value for the measured vibration waveforms.
The recorded waveform signals can also be read on a PC using the loader.
• The automatic waveform recording function can operate on the basis of maxi-
mum value recording with trigger update, maximum value recording without
trigger update, or threshold value recording.
• The forced waveform recording function can record one waveform for 360 s
using the loader.
• Waveform files record the following header information: trigger time, SI value of
the recorded waves, synthesized AC acceleration value for calculation, JMA seis-
mic intensity scale equivalent value, maximum Sv value of the 7 selected natural
periods in the waveform records, and checksum value for the waveform data.
This information can be read out via communications.
1-2
Chapter 1. OVERVIEW
• The vibration detection contact output signals turn ON according to the results
of calculation and according to the following four conditions with AND or OR
relationships:
• When the SI value exceeds the preset value
• ‌When the JMA seismic intensity scale equivalent value exceeds the preset
value
• ‌When the synthesized AC acceleration value (for calculation or for control)
selected for the PV exceeds the preset value
• ‌When liquefaction is detected There are three vibration detection contact out-
puts, for which individual conditions can be set.
• The user can adjust the 4–20 mA analog output using the PV bias and PV low
cutoff function.
• During operation, various diagnostics are conducted. If an error is found, a
minor or serious failure will occur. The diagnosis results are output to the minor
failure or serious failure output.
• If there is a large acceleration input that does not have seismic wave character-
istics, the noise (interference) protection function of this unit will be activated.
When activated, noise protection affects the vibration detection output and ana-
log output for about 1 minute. During this time the noise protection output is
ON.
• If the unit receives a digital input signal, it goes into maintenance mode, sus-
pends the basic earthquake measurement functions, and executes DO, AO, and
relay output sequence operations for accelerometer and input/output diagnosis.
In the case of abnormal results from the accelerometer diagnosis, a serious fail-
ure occurs.
• The following operations can be done with the loader: changing various calcula-
tion parameters such as vibration detection output settings, collecting waveform
records, monitoring the measured values, and monitoring detailed error diagno-
sis results.
• Data can be read and settings can be changed remotely through RS-485 commu-
nications.
A DCX350 remote data collector and a dedicated display unit (with application
software) can be connected.
• Using the loader, the settings can be changed to obtain functions (input/out-
put and operation) that are basically equivalent to those of the SES60 (the old
model).
• The unit casing has a pressure-resistant explosion-proof construction (Ex d IIC
T4) and an IP67 seal.
Model selection
Standard model SES70AV320-1110
With inspection report SES70AV320-111D
Inspection report + traceability certificate SES70AV320-111Y
1-3
Names of parts
Cable gland Adjustment hole for manufacturer
Level adjustment M6 use only (3 places)
Cable clamp Cover
screw hole (3 places)
Lock nut Warning label φ7 device mounting hole (3 places)
Battery
Battery holder
Screw terminal block
(M3.5, 8 terminals)
Loader jack socket
Washer
Flameproof Battery connector (2 places)
packing set Flameproof
packing
Washer
Reference plane
Rating nameplate Spring terminal
O-ring block (10 terminals)
Status display LEDs

LEDs 1 to 3: red Internal ground terminal
External ground terminal LED 4: green
(For cable connections, use ring
crimp terminals suitable for Case Z
X
cables whose cross-sectional Acceleration measurement axes
area is 4 mm2 or larger.) Y Along the Z axis, the direction of
the earth's gravitation is the
positive direction.
Note
• The arrows for the acceleration measurement axes show the directions of
acceleration in response to vibration. When the sensor moves in the direction
indicated by an arrow, the acceleration is positive in that direction. When
the sensor is tilted in the direction indicated by an arrow, the acceleration is
measured as negative in that direction.
Measurement principles (P. 2-2)
Basic function block diagram

Vibration detection relay output (3)
Synthesized AC
acceleration output (AO1)
Input signal processing SI value output (AO2) Changeable
Temperature
Calculation and Minor failure output (DO1)
sensor
input/output judgment Serious failure output (DO2)
Input-output
16-bit A/D
control circuit Noise protection output (DO3)
X conversion circuit
Y Liquefaction detection output (DO4)
Accelerometer Z RS-485 (DA)

CPU
RS-485 (DB)
Mode transition request input (DI)
Clock
Smart Loader communication
D/A conversion
circuit
Memory
Accelerometer Waveform records
self-diagnosis
Note: The memory and the clock are backed up by the battery.
2-1
Internal structure
111 mm
122.5 mm
Explosion-proof case
Waveform records
RISC microcomputer
real-time SI calculation
Accelerometer
Measurement principles
The accelerometer uses a highly sensitive position detector to precisely detect the
positional deviation of the pendulum in response to acceleration. It then sends an
electrical signal (current) proportional to the positional deviation of the pendulum
from the servo-amplifier to the drive circuit (drive coil+magnet) in order to return
the pendulum to the reference point position.
Since the electrical signal from the servo-amplifier is proportional to the accelera-
tion, the acceleration can be measured from the electrical signals.
In the accelerometer, the pendulum is normally located at the reference position
when in the earthquake measurement state, and stress applied to the spring of the
pendulum does not affect the measurement. Therefore, acceleration can be mea-
sured with high accuracy.
P: Pendulum
B: Spring B
C: Drive coil
M: Magnet
D: Position detector P
S: Servo circuit
I: Electrical signal for measurement I
S
C
M
Structure of the accelerometer
• If the unit is dropped accidentally or if a falling object, etc., strikes the unit,
device failure may result. Take care when installing the unit.
2-2
WARNING
Institute of Industrial Safety's User's Guidelines for Electrical Installations for Explosive Gas
Atmospheres in General Industry (Tokyo, 1994 [in Japanese]).
This unit is certified as a pressure-resistant explosion-proof construction (Ex d IIC T4).
Install this unit in a location conforming to the conditions for a flameproof structure.
In Taiwan, this device cannot be used in an explosive atmosphere.
CAUTION
During installation or maintenance work, take care not to drop the unit accidentally to prevent
injury to feet, etc.
This unit is not protected against lightning. As necessary, take appropriate instrumentation to pro-
tect equipment from lightning.
Do not subject this device to shock that exceeds the operating conditions stated in the specifica-
tions. Doing do so may cause device failure.
Installation Location
Avoid installing the device where it will be subject to conditions such as the following.
• Ambient temperature below −10 °C or above +60 °C
• Humidity higher than 90 % RH
• Sudden temperature fluctuations causing condensation
• Corrosive or combustible gas.
• Large amounts of conductive substances (e.g., dust, salt, or iron powder) or
organic solvents
• Direct shock or vibration other than earthquake motion
• Direct sunlight
• Large amounts of water or rain
• Splashing by fluids (e.g., oil or chemicals)
• Strong magnetic or electrical fields
Installation Instructions
This unit measures ground acceleration caused by earthquake motion in order to
calculate the estimated amount of damage. Installation of this unit on a concrete
foundation separated from buildings is recommended so that building vibration
does not affect measurement.
In addition, where needed to prevent direct exposure to sunlight or rain, provide a
protective roof or cover.
• Do not use the three adjustment holes (which are for manufacturer use only)
when installing the unit.
• When installing the unit on a concrete foundation, check that the foundation
is not hollow by tapping it with a small hammer.
3-1
When installing this unit, select one of the methods shown below, depending on the
installation conditions.
zz If the installation surface is level within ±3°
(1) Select a flat concrete surface for installation.
(2) Put three anchors in the surface, aligned with the three 7 mm mounting holes in
the unit.
(3) Attach the unit with the three mounting screws (M5 × 30 mm).
Sensor unit
Concrete
Anchor
Note
• Example of an anchor: PY4002 AY plug bolt
zz If the installation surface is not level
(1) Get
‌ a metal plate (10 mm thick or more) with three holes for level adjustment
and three threaded M5 holes for attaching the unit. The dimensions of the
mounting plate are shown below.
Unit: mm
142
71
15
φ13 (3 places)
41
103
123
43
17
82
M5 (3 places)
44.5
104
10
• If the mounting plate is attached to a concrete surface, use M10 or larger
anchors.
The diameter of the corresponding holes in the plate is 13 mm.
3-2
(2) Put three anchors in the concrete surface for attaching the mounting plate.
(3) Attach the mounting plate to the anchors as shown in the figure below.
M10 M5
Sensor unit
Upper nut
Mounting plate
Lower nut
Concrete
Anchor
(4) Adjust the three lower nuts so that the mounting plate is level.
(5) Tighten the upper nuts to secure the plate.
• Tighten the three upper nuts evenly so that the plate remains level.
• After the mounting plate has been installed, make sure that it is level
within ±2°.
(6) Temporarily tighten the mounting screws (M5 × 20 mm) included with the unit.
(7) Check that the unit is level.
(8) Make fine adjustments of the M6 hexagon socket setscrews so that the unit is
level.
(9) Tighten the three mounting screws (M5 × 20 mm), which were previously tight-
ened temporarily, to secure the unit.
Sensor unit
M5 retaining screw M6 hexagon socket setscrew
Mounting plate
zz What to check after installation

Place a level on the reference plane of this unit to check that the unit is level within
±3°.
If the unit is not installed correctly, malfunction could result.
3-3
Chapter 4. WIRING
WARNING
Institute of Industrial Safety's "User's Guidelines for Electrical Installations for Explosive Gas
Atmospheres in General Industry" (Tokyo, 1994 [in Japanese]).
Use cables with a heat resistance to temperatures of 80 °C or more.
If a cable with a heat resistance of less than 80 °C is used, the unit will no longer be a certified explo-
sion-proof product. Moreover, fire or device failure may result.
Always use the cable gland and flameproof packing set supplied with this unit.
Use packing that is appropriate for the cable. If the wrong packing is used, the unit will no longer be
a certified explosion-proof product.
Before doing wiring work, be sure to disconnect the power. Failure to do so may result in an electric
shock.
During installation, trial runs, and maintenance work, do not touch the power terminals. There is a
risk of electric shock.
During installation, trial runs, and maintenance work, if the unit malfunctions, immediately
disconnect the power.
If the cover is open in a hazardous area, do not turn on the electricity.
When there might be an explosive atmosphere, do not open the cover.
If you use the Smart Loader Package (sold separately), do so in a non-hazardous area where there is
no danger of explosion or fire.
CAUTION
Use shielded cables for wiring.
Be sure to carry out the wiring work properly. Incorrect wiring may cause device failure. (Particularly,
do not mistakenly connect the DO to the RS-485 terminal.)
The power and signal lines must be isolated from the ground. Otherwise, noise could cause mal-
function or device failure.
Do not allow crimp terminals (etc.) to come into contact with adjacent terminals.
Doing so may cause fire or device failure.
Be sure to use bootlace ferrules when wiring the spring terminal block.
Do not use a walkie-talkie or other transceiver within 2 m of this unit or cables connected to this
unit. Doing so may cause this unit to malfunction.
Take care not to damage the threads on the case or cover.
If the threads are damaged, the cover will not open and close properly.
4-1
Chapter 4. WIRING
Wiring Procedure
(1) Loosen the setscrew to open the cover.
• If it is difficult to open the cover, put an appropriate tool, such as the
handle of a screwdriver, in the grooves on the cover after the case has
been secured, and then turn the tool in the direction indicated by the
arrow to open the cover.
• If the tool slips, you may be injured. Always carry out the above work
carefully.
1) Attach the case securely.
2) Insert a tool into the grooves

in the cover and turn counterclockwise.
(2) The cable lead-in system of this unit uses flameproof packing. The compatible
cable outer diameter is 10–14 mm. The following flameproof packing sets cor-
responding to cables are included with this unit. Use packing that is appropriate
for the cable.
Flameproof packing set for 10–12 mm outer diameter cable
Flameproof packing set for 12–14 mm outer diameter cable
(3) Insert the cable into the unit as shown below, and connect the cable to the ter-
minal block.
(4) Screw in the cable gland so that the amount of compression corresponds to the
cable outer diameter as specified in the "Cable outer diameter and amount of
packing compression" table below.
(5) Tighten the lock nut.
(6) ‌Secure the cable using the cable clamp. (tightening torque: 0.6 N·m)
(7) Connect the battery cable included with this unit to the battery connector and
insert the battery into the battery holder. The cable can be connected to either
battery connector.
Cable gland connection port
Washer
Flameproof packing Flameproof packing set
Washer
Clamp tightening screw
Cable gland
Cable
Lock nut
Cable clamp
4-2
Chapter 4. WIRING
Note
• The table below shows the proper amount of packing compression for various
cable diameters.
The appropriate amount of packing compression varies depending on the cable
diameter and the packing inner diameter. Measure the outer diameter of the
cable and choose the most appropriate amount of compression for the cable from
the table below. The amount of compression can also be adjusted by the number
of screw rotations. In the table, counting of the number of screw rotations begins
when the cable gland contacts the packing.
Cable outer diameter and amount of packing Packing compression (left: before, right: after)
compression
Before tightening After tightening
Cable outer Packing inner Packing No. of screw (A) (B)
diameter diameter compression rotations Cable gland
(mm) (mm) (mm)
φ 10.0 min. 12 3.9 2.1
φ 10.5 3.5 1.9
φ 11.0 3.1 1.7
Packing
φ 11.5 2.7 1.5 Clamp tightening screw* Length A-B = Amount of compression of packing
Less than φ 12.0 2.2 1.2
φ 12.0 min. 14 4.5 2.5 Tighten the clamp tightening screws to a maximum torque of 0.6 N·m.
φ 12.5 4.0 2.2
φ 13.0 3.5 1.9
φ 13.5 2.9 1.6
φ 14.0 2.3 1.3
zz Wiring diagram
0.5
Notes. •‌ Terminal SG (for RS-485) is connected to terminal 2 in the terminal block inside the unit.
• Do not connect the DO to the RS-485 terminals.
4-3
Chapter 4. WIRING
zz Screw terminal block

Terminal No. Signal
1 Power (+) (12/24 V DC)
2 Power (-) (0 V DC)
3, 4 Relay contact output 1 (vibration detection output 1)
zz Spring terminal block

Terminal No. Signal
9 Analog output 1: 4–20 mA
([synthesized AC acceleration], SI value, JMA seismic intensity scale equiv-
alent value)
10 Analog output 2: 4–20 mA
(synthesized AC acceleration, [SI value], JMA seismic intensity scale equiv-
alent value)
11 Digital output 1
(minor failure output*1/mode display, [positive logic], negative logic)
12 Digital output 2
(serious failure output*2, [positive logic], negative logic)
13 Digital output 3
(noise protection output, [positive logic], negative logic)
14 Digital output 4 (liquefaction detection output)
15 Digital input
(transition request to maintenance mode/standby mode and diagnos-
tic phase change request in the maintenance sequence)
16 RS-485 DA
17 RS-485 DB
18 RS-485 SG
Note: The default setting is enclosed in brackets, [ ].

‌ minor failure does not affect control output, but a check should be made for waveform record and clock data storage
*1. A
errors, as well as clock data errors. The installation conditions should also be checked. While LED 4 (green) is lit, LED 1 (red)
is lit and digital output 1 (DO1) turns ON.
In any mode other than measurement mode, DO1 repeatedly turns ON and OFF. In addition, by changing the setting, it
can be made to turn ON only when a minor failure occurs.
‌ serious failure may affect control output such as vibration detection output and liquefaction detection output. While
*2. A
LED 4 (green) is lit, LED 2 (red) is lit Then digital output 1 (DO1) turns ON. Note that when a serious failure occurs, minor
failure output (DO1) is also generated.
4-4
Chapter 4. WIRING
• For explosion-proof instrumentation, install and wire this unit in accordance
with the National Institute of Industrial Safety's User's "Guidelines for
Electrical Installations for Explosive Gas Atmospheres in General Industry"
(Tokyo, 1994 [in Japanese]).
• Keep wiring away from cables connected to a commercial power supply or
motor drive power supply that is likely to produce electrical noise.
• If this unit is used alone, its miswiring protection is effective. However, if
multiple units are connected through RS-485, miswiring of the power source
may cause device failure. Be sure to check that the wiring is correct before
turning the power on.
• For screw terminal connections, use crimp terminals that are the correct size
for M3.5 screws
• For spring screw terminal connections, use wires whose nominal cross-
sectional area is 0.25–0.75 mm2 (24 to 18 AWG), with bootlace ferrules.
Use bootlace ferrules and a crimping tool that comply with the following
standards. Do not insert stripped or soldered ends of stranded wires into the
spring terminal block.
Bootlace ferrule: DIN 46228 sect. 4
Crimping tool: DIN 46228 parts 1 and 4
The compatible bootlace ferrules and crimping tool made by Weidmüller
Japan Co., Ltd. are shown below
Compatible bootlace ferrules made by Weidmüller Japan
Connectable wire (mm2) Stripped wire length (mm) Part No.
0.25 10 H0.25/12
0.34 H0.34/12
0.50 H0.5/14
0.75 H0.75/14
The manufacturer's compatible crimping tool: PZ 6 Roto
• To connect a wire to the spring terminal block, insert a bootlace ferrule into
the hole (push-in system).
• To remove a wire from the spring terminal block, push the button on the
block using a flat-head screwdriver (tip size: 0.4 x 2.5 mm) and pull out the
wire. The standard pushing force on the button and the pushed distance are
20 N and 1.7 mm respectively. If the pushing force on the button is 40 N or
greater, device failure could result.
• For wiring for RS-485, do not connect an external terminating resistor.
• For wiring, follow the wiring diagram.
• Use shielded cables for wiring.
Use a shielded cable to wire the ground terminal inside the case.
Use either of the following methods so that there is only one ground connection.
(1) ‌Ground the other end of the shielded cable that is connected to the
ground terminal inside the case.
(2) Ground the ground terminal that is outside the case.
The ground connection should have a resistance of 100 Ω or less. For
lightning surge protection, follow the connection sample on page 4-6.
4-5
Chapter 4. WIRING
Connecting the battery
Battery
Battery holder
Battery connector (2 places)
• If the battery included with this unit is not used, the clock data and
recorded waveform data will not be backed up while power is not being
supplied. In this case, the unit will have a minor failure status.
• If the battery is not connected to the unit or if the clock is not set, the unit
will have a minor failure status.
• If the removed battery is connected to the unit again, the unit may take
time to recognize the battery. Until it is recognized, the unit will have a
minor failure status.
Lightning surge protection

When extended signal and power lines are used, if there is a risk of power surge caused
by lightning, use Azbil Corporation's FA SurgeNon surge protector (QN430C series).
Model No. Status Power supply
QN430C300 Signal line I Signal line I 100 V AC
QN430C304 Signal line I Signal line II 100 V AC
QN430C308 Signal line II Signal line II 100 V AC
Signal line I: F or power and signal lines other than RS-485 lines
(The line limit voltage is 50 V max. The line discharge start voltage is 30 V or more.)
Signal line II: For RS-485 signal lines
(The line limit voltage is 15 V max. The line discharge start voltage is 9 V or more.)
SurgeNon
Signal +
• Power source
Signal - • RS-485 host device
• Control devices (DO, DI, AI)
FG
SES70 : Voltage-limiting element
4-6
Chapter 4. WIRING
zz Connection example
Shielded cable
SES70
Power supply
Power +24 V
supply 0V
FG
Vibration detection Receiver for vibration

output 1 detection signal 1


Synthesized AC
Synthesized AC acceleration
acceleration
analog receiver
SI SI analog receiver
Soft failure Minor failure digital

receiver
Serious failure Serious failure digital

receiver
Noise protection Noise protection

digital receiver
Liquefaction Liquefaction detection

digital receiver
Diagnosis Diagnostic digital

output
+24 V Power supply

0V
FG
DA
RS-485 Display unit
DB
SG
FG
FG FG
4-7
Chapter 4. WIRING
• Make the wiring between the SurgeNon and the unit, power supply, receiver,
etc., as short as possible.
• For wiring for RS-485, do not connect an external terminating resistor.
If a terminating resistor is connected to either end of the transmission line,
communication is not possible.
Note
• The 100 V AC supplied to the SurgeNon (terminals (3) and (4)) is used for
indication. Even if this power is not supplied, the lightning surge protective
function is operative.
4-8
WARNING
Set the time using the SLP-SE7 Smart Loader Package (sold separately).
Here the SLP-SE7 Smart Loader Package will be referred to simply as the loader.
Procedure for setting the clock

(1) While the power to the unit is turned off, open the cover and connect the loader.
• If the plug is plugged into the loader jack while the power is turned on,
waveforms from the impact of the connection may be recorded.
(2) Turn
‌ ON the power to this unit and wait until initialization mode changes to
measurement mode (until LED 4 (green) is lit).
(3) Set
‌ the time on the unit's built-in clock using the loader. If 360 s or more pass
since LED 4 lit up (since the mode changed to measurement mode), previously
recorded waveforms may remain. To prevent this problem, finish setting the
time so that the unit can go into standby mode within 360 s.
After the time is set, change the mode to initialization mode using the loader.
(4) After
‌ the time is set, wait until initialization mode changes to measurement
mode (wait until LED 4 is lit). ‌
(5) Make
‌ sure that only LED 4 is lit (normal operation).
• If another LED (red) is blinking, an error has occurred. Check the
details on the error on the detailed error screen of the loader and
take corrective actions as specified in Chapter 8, MAINTENANCE AND
TROUBLESHOOTING, of this manual.
• If 360 s or more pass after LED 4 lights up, previously recorded waveforms
may remain. Complete the check within 360 s.
(6) Make
‌ sure that the unit is working properly, and then turn off the power and
disconnect the loader.
• If the loader plug is removed from the jack while the power is ON,
waveforms caused by the motion may be recorded.
(7) Firmly tighten the cover until its flange tightly contacts the top edge of the case.
(8) Turn
‌ on the power. After approximately 60 s have elapsed, Initialization mode
changes to measurement mode, and the unit is then ready for earthquake mea-
surement.
SLP-SE7 Smart Loader Package for SES70 Intelligent Earthquake Sensor,
No. CP-UM-5756E
5-1
Note
• Before putting the unit into actual operation for the first time, clear the
waveforms using the loader before turning OFF the power in step (6) so
that the waveforms recorded during setup work are deleted. The waveforms
recorded during work can be cleared completely.
• If the time has not been set, the clock will start at 00:00 on January 1, 2050,
and the unit will have a minor failure status.
• When tightening the cover, take care to prevent cables from being caught.
Note
• If the earthquake sensor is shaken manually to check the calculations of
synthesized AC acceleration value, SI value, JMA seismic intensity scale
equivalent value, and vibration detection judgment value of the earthquake
sensor, carefully observe the following cautions:
(1) ‌Check the operation after the unit has entered measurement mode. The
correct output cannot be obtained in initialization mode. Additionally, any
acceleration that is applied to the unit in initialization mode is judged as an
error and the mode may not change to measurement mode.
(2) ‌When applying any acceleration to the unit, do not tilt the earthquake sensor
and be sure to shake it evenly in both the positive and negative directions.
Additionally, do not stop manual shaking suddenly. Reduce the amplitude
gradually.
• If the earthquake sensor is tilted, it will enter the noise detection
function's zero-cross noise detection state and a value smaller than the
actual value may be output.
6 - 5 Noise Protection Function (P. 6-24)
• If the earthquake sensor is shaken unevenly in the positive and negative
directions, it will enter the noise detection function's ratio noise detection
state, and a value smaller than the actual value may be output.
• If manual shaking is stopped suddenly, the input acceleration in one
direction will be large. Therefore, the sensor will enter the noise detection
function's ratio noise detection, possibly preventing the correct value
from being output.
5-2
6 - 1 Modes
Mode transition
After the earthquake sensor is turned on, it operates according to the mode transi-
tions shown below. There are four modes, which change depending on the specific
operation or conditions.
POWER ON
Initialization mode
• Diagnostic input DI1
Normal initialization completion • Serious failure occurrence
• Diagnostic input DI1 (system error)
• Transition request from loader • Transition request from loader
• Mode timeout • Mode timeout
(except for system errors) (except for system errors)
Maintenance mode Measurement mode Standby mode

• Diagnostic input DI1 • Transition request from loader
• Transition request from loader
• Note that when the power is turned on or off, if the power slowly rises or
drops, the analog output may fluctuate.
6-1
Functions of the modes

The available functions vary depending on which of the four modes below is active.
Initialization mode
Measurement mode
Standby mode
Maintenance mode
zz Initialization mode
In this mode the hardware is checked and system control information and numeri-
cal processing values are initialized. The unit then waits until its operation stabiliz-
es. If the result of the hardware check is normal, the mode changes to measurement
mode. If a serious failure occurs in this mode, it is judged to be a system error and
the mode changes to standby mode. Also, if the DI1 diagnosis input is kept ON for
2 s or longer in initialization mode after the power has been turned ON, the mode
changes to standby mode.
Status of functions in initialization mode

Function Status
Initialization for internal calculations (acceleration, SI, synthesized AC acceleration, JMA 
seismic intensity scale equivalent value calculations)
Internal calculations (acceleration, SI value, synthesized AC acceleration, JMA seismic inten- ––
sity scale equivalent value calculations)
Noise detection ––
Vibration detection judgment and output ––
AO output (SI value, synthesized AC acceleration, JMA seismic intensity scale equivalent ––
value)
Liquefaction judgment and output ––
Automatic waveform recording ––
Forced waveform recording ––
Waveform readout 
Waveform deletion 
Maintenance mode sequence operation ––
Initialization mode error diagnosis and output 
Measurement and standby mode error diagnosis and output ––
Maintenance mode error diagnosis and output ––
Manual output ––
LED indication 
Communications data readout 
Communications data writing ––
Sensor internal clock setup 
 : Available ––: Not available
6-2
zz Measurement mode
The mode changes to measurement mode if no serious failures are detected and
if initialization mode operations are completed correctly. In measurement mode,
the various operations and judgment processes that are the basic processing of an
earthquake sensor are executed. The AO output, vibration detection judgment out-
put function, and liquefaction judgment output function are executed based on the
SI value, synthesized AC acceleration, and JMA seismic intensity scale equivalent
value. Additionally, automatic waveform recording is executed.
Status of functions in measurement mode

Function Status
Initialization for internal calculations (acceleration, SI, synthesized AC acceleration, JMA ––
Internal calculations (acceleration, SI value, synthesized AC acceleration, JMA seismic inten- 
Noise detection 
Vibration detection judgment and output 
AO output (SI value, synthesized AC acceleration, JMA seismic intensity scale equivalent 
value)
Liquefaction judgment and output 
Automatic waveform recording 
Initialization mode error diagnosis and output ––
Measurement and standby mode error diagnosis and output 
LED indication 
 : Available ––: Not available
6-3
zz Standby mode
The mode changes to standby mode if any of the following occurs:
• In measurement mode, a mode transition command is received via communica-
tions.
• In initialization mode, a system error occurs when a serious failure is detected.
• After the power has been turned ON in initialization mode, the DI1 diagnosis
input is kept ON for 2 s or more.
The calculation and judgment processes function in the same manner as in mea-
surement mode. It is also possible to change various settings and to manually set
various outputs using the loader.
Automatic waveform recording is not available, but forced waveform recording can
be executed using the loader.
If the mode changes to standby under conditions other than a system error, it will
automatically change to initialization mode due to time-out if 20 minutes have
passed since the mode transition and there has been no communication.
Status of functions in standby mode

Function Status
Initialization for internal calculations (acceleration, SI, synthesized AC acceleration, JMA ––
Internal calculations (acceleration, SI value, synthesized AC acceleration, JMA seismic inten- 
Noise detection 
Vibration detection judgment and output 
AO output (SI value, synthesized AC acceleration, JMA seismic intensity scale equivalent 
value)
Liquefaction judgment and output 
Forced waveform recording 
Measurement and standby mode error diagnosis and output 
Manual output 
LED indication 
Communications data writing 
: Available ––: Not available
6-4
zz Maintenance mode
The mode changes to maintenance mode if a mode change command is received
in measurement mode via communications or if the DI1 diagnosis input is kept
ON for 2 s or longer. An operational check of the earthquake sensor input, output,
and accelerometer is conducted as phases 1–3 of the maintenance sequence. In this
mode, internal calculation equation and output judgment functions do not operate.
After the operational check in each phase, if there is a command via communica-
tions or if the DI1 diagnosis input is kept ON for 2 s or longer, an operational check
is done for the next phase.
After the maintenance sequence has been completed, if there is a command via
communications or if the DI1 diagnosis input is kept ON for 2 s or longer, the mode
changes to initialization mode. Also, if 20 minutes have passed since the mode
changed to maintenance mode, it will automatically change to initialization mode
due to time-out.
Status of functions in maintenance mode

Function Status
Initialization for internal calculations (acceleration, SI value, synthesized AC acceleration, ––
JMA seismic intensity scale equivalent value calculations)
Internal calculations (acceleration, SI value, synthesized AC acceleration, JMA seismic inten- ––
Noise detection ––
Vibration detection judgment and output ––
AO output (SI value, synthesized AC acceleration, JMA seismic intensity scale equivalent ––
value)
Liquefaction judgment and output ––
Maintenance mode sequence operation 
Measurement and standby mode error diagnosis and output ––
Maintenance mode error diagnosis and output 
LED indication 
6-5
zz Status of functions in all modes

Initialization mode
Measurement mode
Standby mode
Maintenance mode
Status of functions in all modes

Function Initialize Measurement Standby Maintenance
Initialization for internal calculation (acceleration, SI value , synthe-
sized AC acceleration, JMA seismic intensity scale equivalent value  –– –– ––
calculations)
Internal calculations (acceleration, SI value, synthesized AC accelera-
tion calculations, JMA seismic intensity scale equivalent value calcula- ––   ––
tions)
Noise detection ––   ––
Vibration detection judgment and output ––   ––
AO output (SI value, synthesized AC acceleration, JMA seismic inten-
––   ––
sity scale equivalent value)
Liquefaction judgment and output ––   ––
Automatic waveform recording ––  –– ––
Forced waveform recording –– ––  ––
Waveform readout    
Waveform deletion    
Maintenance mode sequence operation –– –– –– 
Initialization mode error diagnosis and output  –– –– ––
Measurement and standby mode error diagnosis and output ––   ––
Maintenance mode error diagnosis and output –– –– –– 
Manual output –– ––  ––
LED indication    
Communications data readout    
Communications data writing –– ––  ––
Sensor internal clock setup    
6-6
6 - 2 Internal Calculation Processes

Internal Calculation
X-, Y-, and Z-axis acceleration signal (V) Temperature signal (V)
Acceleration filter calculation for calculation Acceleration filter calculation for control
X-, Y-, and Z-axis acceleration signal for calculation Temperature signal X-, Y-, and Z-axis acceleration signal for control
Acceleration characterization compensation calculation Acceleration characterization compensation calculation
X-, Y-, and Z-axis acceleration compensation value for calculation (Gal) X-, Y-, and Z-axis acceleration compensation value for control (Gal)
Acceleration bias calculation Acceleration bias calculation
X-, Y-, and Z-axis adjusted acceleration value for calculation (Gal) X-, Y-, and Z-axis adjusted acceleration value for control (Gal)
AC acceleration and inclination acceleration filter calculation AC acceleration and inclination acceleration filter calculation
X-, Y-, and Z-axis AC acceleration for calculation (Gal) X-, Y-, and Z-axis inclination acceleration for calculation (Gal) X-, Y-, and Z-axis AC acceleration for control (Gal) X-, Y-, and Z-axis inclination acceleration for control (Gal)
Flowchart of acceleration signal processing

zz Acceleration filter calculation
The output from the accelerometer is passed through two low-pass filters set for dif-
ferent cutoff frequencies that are useful for different applications in order to obtain
two acceleration values. These are acceleration for calculation of frequency character-
istics, for calculating an index, and acceleration for control of frequency characteris-
tics, for noise reduction by taking the AO and relay output into consideration.
The low-pass filter can be changed by setting the acceleration filter value in the loader.
Initial value: 30 Hz for calculation, 10 Hz for control
zz Acceleration characterization calculation (acceleration compensation value)
This calculation compensates for an output error of an individual accelerometer.
The acceleration compensation value includes compensation for the accelerometer's
sensitivity and zero-point, and for the temperature.
zz Acceleration bias calculation (adjusted acceleration value)
Using the auto bias function of the loader, the acceleration compensation value bias
is adjusted according to the installation conditions in order to calculate the adjusted
acceleration value.
The adjustment is made so that the adjusted acceleration value is near 0 Gal under
the current installation conditions.
Waveforms are recorded using adjusted acceleration values for calculation.
• Acceleration is always detected in a range of ± several gals due to the
specifications of the acceleration detection element. Therefore, the
adjusted acceleration value does not exactly equal 0 Gal.
zz AC acceleration and inclination acceleration filter calculations (AC acceleration and inclination acceleration)
The inclination acceleration is calculated by passing the adjusted acceleration value
through a low-pass filter (0.05 Hz). Inclination acceleration is the static acceleration
due to temperature or inclination.
AC acceleration is the result of subtracting the inclination acceleration from the
adjusted acceleration.
AC acceleration is the amount of dynamic acceleration.
AC acceleration = adjusted acceleration - inclination acceleration
6-7
Various calculations and judgment processes

This section gives an overview of the calculation processes. Each calculation is
executed at intervals of 10 ms.
6 - 7 Output Functions (P. 6-29)
shows calculations and judgment processes.
shows the resulting values.
X adjusted acceleration for control X AC acceleration for control
3-axis synthesized AC acceleration

X inclination for control 3-axis synthesized AC acceleration calculation
raw value for control
Y adjusted acceleration for control Y AC acceleration for control
Y inclination for control
2-axis synthesized AC acceleration

Z adjusted acceleration for control Z AC acceleration for control 2-axis synthesized AC acceleration calculation raw value for control
Z inclination for control 3-axis synthesized AC acceleration

3-axis synthesized AC acceleration calculation
raw value for calculation
X adjusted acceleration for calculation X AC acceleration for calculation Synthesized AC acceleration

X inclination for calculation 2-axis synthesized AC acceleration

2-axis synthesized AC acceleration calculation
Y adjusted acceleration for calculation Y AC acceleration for calculation

SI calculation SI raw value
Y inclination for calculation JMA seismic intensity calculation

JMA seismic intensity raw value 1
Waveform recording trigger process
Z adjusted acceleration for calculation Z AC acceleration for calculation JMA seismic intensity raw value 2
Recorded waveform data Z inclination for calculation Liquefaction judgment Liquefaction judgment raw value
Vibration detection judgment

Noise judgment process
Vibration detection judgment raw value
Flowchart of various calculation and judgment processes
6-8
PV PV bias 3-axis synthesized AC adjusted acceleration value for control

noise protection
PV PV bias 2-axis synthesized AC adjusted acceleration value for control

noise protection
Values that the user reads out as PV
PV PV bias 3-axis synthesized AC adjusted acceleration value for calculation

noise protection
Synthesized AC acceleration (PV)
PV PV bias 2-axis synthesized AC adjusted acceleration value for calculation

noise protection
PV PV bias Adjusted SI value SI value (PV)

noise protection
PV JMA seismic intensity value (PV)

noise protection
DO Liquefaction judgment value (PV)

noise protection
DO Vibration detection judgment value (PV)

noise protection
6-9
SI calculation
The SI value indicates how much destructive power is applied to virtual structures
(such as buildings), which are created by equations, based on the actual vibration
detected by the sensor on the ground.
Therefore, this value serves as an index for the amount of damage to actual struc-
tures. As shown below by actual earthquake damage data in "Relationship between
SI value and maximum acceleration," there may be only minor damage from an
earthquake with large acceleration, but there is major damage if the earthquake has
an SI value of approximately 30 kine or more. Therefore earthquake damage is cor-
related more with SI value than with acceleration.
The virtual structure used for the SI calculation consists simply of a weight, spring,
and damper having only one direction of motion and one natural period, which
form a system with 1 degree of freedom and 1 mass.
For structures with a major natural period between 0.1 and to 2.5 s, as shown below
in "Example of Sv calculation by natural period," a calculation is done for each of
seven natural periods. In these calculations, the shaking of the earth (acceleration)
detected by the accelerometer is used as input from which the speed response is cal-
culated. The largest of the speed responses is the Sv.
Since the SES70 executes the calculations in real time, the Sv value is obtained from
the speed responses for the past 10 to 20 s. As the speed responses become smaller
over time, the Sv value also becomes smaller.
To calculate the SI value, linear interpolation is applied to the result of calculation
for each natural period as shown in "Example of Sv calculation by natural period,"
in order to calculate the average of the Sv values for 0.1 to 2.5 s.
Also, the SI value calculated from the earthquake waveform has a directional
dependency, as shown in the figure, "Example of SI calculation in eight directions."
Therefore, the speed responses and Sv value on the horizontal plane in eight direc-
tions are determined in order to calculate the SI for each of the eight directions.
The SI that is finally output is the largest of the values in the eight directions.
The SI value calculated by the SES70 on the basis of the seven natural periods and
vector projection in 8 directions is called SI #1. An SI value calculated on the basis
of 24 natural periods and 16 directions, which is called SI #2, can also be selected.
zz SI equation
[SI equation]
1 2.5 Sv: Speed response spectrum
SI= 2.4 0.1

SvdT(h=0.2) T: Period
h: Damping constant
zz Relationship between SI value and maximum acceleration

120
110
Hanshin Awaji
100 Damage to area buildings, etc. (Kobe)
90 No damage
80
70
SI (kine)
Miyagi Pref., offshore (Shiogama)

60
Tokachi, offshore
50 (Hachinohe) Tokachi, offshore
(Aomori) Matsushiro Gunpatsu
Nemuro peninsula,
40 offshore El Centro
(Kushiro) Hyuganada (Hosojima)
30 Izu Peninsula, Sea of Japan,
near offshore central (Akita)
20 (Kakita River) Tokachi, offshore
(Muroran)
10
0
100 200 300 400 500 600 700 800 900
Maximum acceleration (Gal)

Unit of SI value: kine = cm/s
6-10 Unit of acceleration: Gal = cm/s2
The SI value is the average of the

speed response spectrum (Sv) for a
Sv value (kine)
period (T) of 0.1 to 2.5 s.
As shown in the figure on the
left, the SES70 uses a polygon to
approximate the speed response
spectrum (Sv) of each of the seven
natural periods in order to obtain a
highly accurate SI calculation.
Note: ‌SI calculation on the basis of
24 natural periods can also
0.1 0.4 0.7 1.0 1.5 2.0 2.5 Natural period (s) be selected.‌
Example of Sv calculation by natural period
90°
120° 60°
150° 30° Since the SI value varies depend-

ing on the direction from which
the seismic waves come, calcula-
0° SI value (kine) tions in multiple directions are
180°
0 20 40 60 80 100 necessary.
As shown in the figure on the left,
the SES70 calculates SI values
210° 330° in eight directions and uses the
greatest of these values to obtain
240° 300° high accuracy in the SI calculation.
270° Note: ‌SI calculation in 16 directions
can also be selected.‌
Example of SI calculation in eight directions
Synthesized AC acceleration calculation

According to the 3-axis (X-, Y-, and Z-axis) AC acceleration value for calculation
and AC acceleration value for control that are detected by the accelerometer, vectors
of two axes on the horizontal plane or of three axes (selectable) are synthesized to
find the maximum value.
The maximum value is taken from the synthesized acceleration values that were
obtained until 10 to 20 s before the current time.
Therefore, the maximum value is retained for the above length of time and then is
updated.
Z-axis acceleration
3-axis vector synthesized value
X-axis acceleration
2-axis vector synthesized value

Y-axis acceleration
Synthesized AC acceleration calculation
6-11
Calculation of the JMA seismic intensity scale equivalent value

Calculation of the seismic intensity (IJMA or JMA seismic intensity) that is equiva-
lent to the measured vibration can be based on either of two correlation equations
formulated by Prof. Yamazaki of the Earthquake Research Institute of the University
of Tokyo. The equations use the adjusted SI value (SI) alone or that value with the
2-axis synthesized AC adjusted acceleration value for calculation (PGA).
The desired equation can be selected using the loader. Default: Equation 1.
Equation 1: IJMA = 1.74 + 1.38 × log10 (SI) + 0.59 × log10 (PGA)
Equation 2: IJMA = 2.39 + 1.92 × log10 (SI)
Note: ‌The correlation between these equations and values from 2.0 to 7.9 on the
JMA seismic intensity scale has been confirmed. The correlation of values
under 2.0 is not reliable.‌
Relationship of the JMA scale (shindo scale), acceleration, SI value, and measured seismic intensity (shindo)
Old Japanese seismic intensity scale New Japanese seismic intensity scale
Applicability of JMA
Seismic intensity Seismic intensity Measured seismic scale equivalence
Acceleration (Gal) SI value (kine)
(shindo) (shindo) intensity (shindo)
0 Less than 0.8 0 Less than 0.5 - ––
1 0.8 to less than 2.5 1 0.5 to less than 1.5 - ––
2 2.5 to less than 8.0 2 1.5 to less than 2.5 - 
3 8.0 to less than 25.0 3 2.5 to less than 3.5 1.1 to less than 3.8 
4 25.0 to less than 80.0 4 3.5 to less than 4.5 3.8 to less than 12.6 
5 80.0 to less than 250.0 5- 4.5 to less than 5.0 12.6 to less than 22.9 
5+ 5.0 to less than 5.5 22.9 to less than 41.7 
6 250.0 to less than 400.0 6- 5.5 to less than 6.0 41.7 to less than 75.9 
6+ 6.0 to less than 6.5 75.9 to less than 138.2 
7 400.0 or more 7 6.5 or more 138.2 or more 
: Applicable
: Depending on the waveform, there may be a large error.
––: Not applicable due to a large amount of error
The JMA seismic intensity scale equivalent value is the same as the measured seismic intensity.
The JMA seismic intensity scale equivalent value is calculated using equation 2.
• The above correspondences between JMA seismic intensity (shindo) and
acceleration can be used for rough estimation. Note particularly that, since
the high-frequency component of acceleration has little effect on the actual
damage, if that component of the acceleration waveforms is large, the error
will be large.
Noise protection process

For the SI value, synthesized AC acceleration for calculation, JMA seismic intensity
scale equivalent value, and the vibration detection judgment and liquefaction judg-
ment raw values, the results of the noise detection process is the PV value.
For any of these numeric values, if noise is detected the output is fixed at 0.
For any of raw values of these judgment results, if noise is detected, the raw value
remains OFF.
6 - 5 Noise Protection Function (P. 6-24)
6-12
6 - 3 Waveform Recording
In waveform recording, the adjusted acceleration values for 3-axis calculations, the data of which is sampled at inter-
vals of 10 ms, are recorded for 360 s if the conditions for recording are satisfied. Data including the date and time, SI
value, synthesized AC acceleration value for calculation, and JMA seismic intensity scale equivalent value is record-
ed as the header information for each waveform recording.
The waveform recording and waveform header information can be read or deleted using the loader. The waveform
recording and waveform header information are saved to RAM backed up by the battery.
Automatic waveform recording (of 10 waveforms) can be done in measurement mode, and forced waveform record-
ing (of 1 waveform) can be done in standby mode.
Waveform recording header information

The following header information is attached to each waveform recording:
Trigger time (year, month, day, hour, minute, second)
Waveform valid and invalid judgments
Maximum synthesized acceleration value for calculation from the trigger point
to the waveform end time
Maximum SI value [SI #1 or SI #2] from the trigger point to the waveform end time
Maximum JMA seismic intensity scale equivalent value from the trigger point to
the waveform end time
Whether or not there was any serious failure, minor failure, or noise from the
trigger point to the waveform end time
Whether or not any liquefaction occurred from the trigger point to the wave-
form end time
Whether or not there is any vibration detection output for the time between the
trigger point and the waveform end time
Inclined acceleration [X-, Y-, and Z-axis] from the trigger point to the waveform end time
Sv values [Sv1–Sv7] from the trigger point to the waveform end time
Checksum value for the waveform data [360 s, 120 s]
Regarding the seven Sv values in the waveform recording header, if SI #2 is chosen
as the SI value, they can be selected from among 24 Sv values by using the loader.
Automatic waveform recording

The basis for starting automatic waveform recording can be selected from among
maximum value without trigger update, maximum value with trigger update, or
threshold value.
The trigger can be selected from among SI value (raw value), synthesized acceleration
for calculation (raw value), and JMA seismic intensity scale equivalent value (PV).
When recording based on maximum value (with or without trigger update) is select-
ed, priority for storage is given to the waveforms with the largest trigger value. The
ten waveforms with the largest trigger values from the start of waveform recording are
retained. If two waveforms have the same trigger value, the newer waveform is retained.
When recording based on a threshold is selected, any waveform whose trigger equals or
exceeds the preset threshold is recorded, and the oldest waveform is deleted.
In maximum value recording without trigger update, after the trigger conditions are
satisfied and recording begins, if the waveform later becomes larger, the trigger is not
updated and the recording start point is not changed. On the other hand, in maxi-
mum value recording with trigger update, after the trigger conditions are satisfied
and recording begins, if the waveform becomes larger, the trigger is reset to the largest
point in the waveform and the start point of the recording is changed.
In the maximum value recording without trigger update, recording always starts at
the head of the waveform, and therefore if the waveform is long, the part of it with the
largest value may not be recorded.
In maximum value recording with trigger update, the part of the waveform with the larg-
est value is always recorded, except perhaps if the waveform exceeds 360 seconds in length.
Default settings: threshold, SI value (raw value) trigger (condition for trigger: 1 kine)
6-13
• As shown below, the default settings for the SES70 are different from
those for the older SES50/51/55/60 models. Be careful when using the
unit without changing the default settings.
Note: ‌The reason for making threshold value recording the default on
the SES70 is that the latest earthquake or tremors will be recorded,
and for checking the stability of the installation. To have the SES70
record large vibrations, change the recording method to maximum
value (Max. Wave).
Default settings for waveform recording (compared with old models)

SES50/51/55/60
SES70
(old models)
Waveform recording Threshold value Maximum value with trig-
ger update
Maximum value (with trigger update) SI value SI value
trigger type
Maximum value (without trigger SI value — (no such function)
update) trigger type
Threshold value trigger type SI value SI value
Threshold value: SI amount 1 kine 30 kine
Threshold value: synthesized accel- 5 Gal 300 Gal
eration amount
Threshold value: JMA intensity 1.0 5.3
amount
The waveform data uses 11 memory pages, P0 to P10. One of these is used as work-
ing memory to record or update the current acceleration waveform data. The ten
waveform data pages (but not the working page memory) can be read using the
loader. If the waveform in the working page memory (the current waveform) satis-
fies the trigger conditions and 360 s of acceleration data is saved, the contents of
the working page are moved to another page, and the current waveform data and
header information are then saved.
• If the cover of this unit is opened and closed or the loader cable is
connected while in measurement mode, the acceleration waveforms
generated by these actions may be recorded, and therefore waveforms
that were previously measured and recorded may be deleted. Always
turn OFF the power to this device during work, including work near the
installation location that may cause vibration or impact.
6-14
Example of maximum value recording without trigger update

In the explanatory diagram below for maximum value recording, chronological
changes in acceleration and SI value are shown to illustrate the methods of accelera-
tion waveform recording when an earthquake occurs. Chronological changes in
waveform header information are also shown in the waveform header information
table ( P. 6-16).
Note that, even though the date is recorded in the actual waveform header informa-
tion, it is omitted from the explanation because all the data has the same date. The
rank column in the header information table shows the priority used for saving of
records in the earthquake sensor based on the trigger time in the header informa-
tion. Data with rank 1 has the highest priority for saving, while rank 10 data will be
the first to be deleted. Assuming that the current time is T, for purposes of illustra-
tion, the automatic waveform recording mechanism is explained along with the
time flow (t1 to t5) shown in the figure and table.
The trigger condition for the following examples is the SI value.
(1) T ≤ t1 (16:04:55) or T < t2 (16:05:00):
The current acceleration data record is updated, with P4 as the work page. The
trigger conditions are not satisfied.
(2) T = t2 (16:05:00):
Since the SI exceeds the SI of the header item P0 (0.1 kine), which has a rank
of 10, and has reached 0.2 kine, the trigger conditions for recording are satis-
fied. Later, if the SI exceeds 0.2 kine, the t2 trigger will not be updated. The
waveform data for 30 s before t2 and the acceleration data for 330 s after t2 are
saved. Other operations wait for completion of 360 s of waveform recording.
Header information and work record area are not changed until the recording
of waveform data for 360 s is completed.
(3) T = t3:
After completion of 360 s of waveform data recording at t3, the work record
area changes to P0 and P4 is retained as recorded waveform data.
Since, as the header information shows, the newly recorded P4 has the 5th
largest SI, its rank becomes 5 and the rank of each of the former 5th and fol-
lowing waveforms is lowered by one.
(6) t3 ≤ T < t4 (16:08:55):
Since the largest SI value in the waveform data in P0, which has now become
the work page, is at time t3, t3 becomes the trigger point. Also, since the wave-
form data before t3 has already been recorded in P4, the 360 s of waveform
data recording starts after trigger point t3.
(7) T = t4:
Since waveform recording for 360 s has been completed at t4, the work record
area changes to P3 and P0 is retained as record data. The header information is
also updated. The rank of P0 then becomes 6.
By means of sequences such as these, the waveform data from t1 to t4 is recorded
onto two pages, P4 and P0. In this case, however, due to the effect of the accelera-
tion of the previously recorded P4, the waveform of the later recorded P0 is not the
26.0 kine SI value waveform shown in the P0 header, but is rather a waveform with
small acceleration. As a result, values calculated from the recorded waveform will
not match the value in the header information. Therefore, when analyzing automat-
ically recorded waveform data, it is necessary to check the trigger time in the header
information to see whether there are consecutive waveforms.
6-15
P4 waveform data P0 waveform data
Acceleration (raw) (Gal)
Time (s)
P4 temporary
trigger point t2
SI value = 0.2 kine
16:05:00
P0 trigger point
SI value = 26 kine
SI value 16:06:55
(raw)
(kine)
T time (s)
360s
30s 330s
t1 t3 t4
= 16:04:30
Explanatory diagram for maximum value recording without trigger update (automatic waveform recording)
Waveform header information (maximum value recording without trigger update)

Page Rank Before t4 Rank t4 to t5 Rank After t5
P0 Trigger time (10) 01:23:09 − Work (6) 16:10:55
Trigger SI value 0.1 kine --- 26.0 kine
P1 Trigger time (6) 03:02:35 (7) 03:02:35 (8) 03:02:35
Trigger SI value 0.3 kine 0.3 kine 0.3 kine
P2 Trigger time (5) 03:04:10 (6) 03:04:10 (7) 03:04:10
P3 Trigger time (9) 02:32:29 (10) 02:32:29 − Work
Trigger SI value 0.1 kine 0.1 kine ---
P4 Trigger time − Work (5) 16:05:00 (5) 16:05:00
Trigger SI value --- 32.0 kine 32.0 kine
P5 Trigger time (7) 10:47:08 (8) 10:47:08 (9) 10:47:08
P6 Trigger time (8) 10:07:33 (9) 10:07:33 (10) 10:07:33
P7 Trigger time (1) 01:08:23 (1) 01:08:23 (1) 01:08:23
P8 Trigger time (2) 04:01:07 (2) 04:01:07 (2) 04:01:07
P9 Trigger time (3) 04:08:12 (3) 04:08:12 (3) 04:08:12
P10 Trigger time (4) 01:06:53 (4) 01:06:53 (4) 01:06:53
6-16
Example of maximum value recording with trigger update

In the same way as for maximum value recording without trigger update, the
chronological changes in acceleration and SI value are shown to illustrate the meth-
od of acceleration waveform recording when an earthquake occurs.
Chronological changes in waveform header information are also shown in the
waveform header information table ( P. 6-18).
(1) T ≤ t1 (16:04:55) or T < t2 (16:05:00):
The current acceleration data record is updated, with P4 used as the work
page. The trigger conditions are not satisfied.
(2) T = t2 (16:05:00):
Since the SI exceeds the SI of the header item P0 (0.1 kine), which has a rank
of 10, and has reached 0.2 kine, the trigger conditions for recording are satis-
fied. Later, if the SI does not exceed 0.2 kine, the waveform data with t2 used as
trigger will be recorded for 360 s and then the data will be saved.
(3) t2 < T < t3 (16:05:25):
Since the SI has now been updated to a larger value, the trigger point is also
updated.
(4) t3 ≤ T < t4 (16:05:50):
Since the SI reached its largest value at time t3 and will not be updated later, t3
becomes the trigger point. The waveform data for 30 s before t3 and the accel-
eration data for 330 s after t3 are saved. Other operations wait for completion
of 360 s of waveform recording. Header information and work record area are
not changed until the recording of waveform data for 360 s is completed.
(5) T = t4:
Since the recording of the waveform data for 360 s has been completed at t4,
the work record area changes to P0, and P4 is retained as recorded waveform
data. The header information is also updated.
Since, as the header information shows, the newly recorded P4 has the 5th
largest SI, its rank becomes 5 and the rank of each of the former 5th and fol-
lowing waveforms is lowered by one.
(6) t4 ≤ T < t5 (16:05:40):
Since the largest SI value in the waveform data in P0, which has now become
the work page, is at time t4, t4 becomes the trigger point. Also, since the wave-
form data before t4 has already been recorded in P4, the 360 s of waveform
recording starts after trigger point t4.
(7) T = t5:
Since the waveform recording for 360 s has been completed at t5, the work
record area changes to P3 and P0 is retained as record data. The header infor-
mation is also updated. The rank of P0 then becomes 6.
not match the value in the header information.
Therefore, when analyzing the automatically recorded waveform data, it is neces-
sary to check the trigger time in the header information to see whether there are
consecutive waveforms.
6-17
Time (s)
P4 temporary t2 P4 trigger point

trigger point SI value = 32 kine
SI value = 0.2 kine 16:05:25
16:05:00 P0 trigger point
SI value = 26 kine
SI value 16:10:55
(raw)
(kine)
30s 330s T time (s)

360s
t1 t3 t4 t5
= 16:04:55
Explanatory diagram for maximum value recording with trigger update (automatic waveform recording)
Waveform header information (maximum value recording with trigger update)

P0 Trigger time (10) 01:23:09 − Work (6) 16:10:55
P1 Trigger time (6) 03:02:35 (7) 03:02:35 (8) 03:02:35
P2 Trigger time (5) 03:04:10 (6) 03:04:10 (7) 03:04:10
P3 Trigger time (9) 02:32:29 (10) 02:32:29 − Work
P4 Trigger time − Work (5) 16:05:25 (5) 16:05:25
P5 Trigger time (7) 10:47:08 (8) 10:47:08 (9) 10:47:08
P6 Trigger time (8) 10:07:33 (9) 10:07:33 (10) 10:07:33
P7 Trigger time (1) 01:08:23 (1) 01:08:23 (1) 01:08:23
P8 Trigger time (2) 04:01:07 (2) 04:01:07 (2) 04:01:07
P9 Trigger time (3) 04:08:12 (3) 04:08:12 (3) 04:08:12
P10 Trigger time (4) 01:06:53 (4) 01:06:53 (4) 01:06:53
6-18
Example of threshold value recording

In the explanatory diagram below for threshold value recording, chronological
changes in acceleration and SI value are shown to illustrate the methods of accelera-
tion waveform recording when an earthquake occurs.
Chronological changes in waveform header information are also shown in the
waveform header information table ( P. 6-20).
Assuming that the current time is T, for purposes of illustration, the automatic
waveform recording mechanism is explained along with the time flow (t1 to t4)
shown in the figure and table.
The trigger conditions and the set threshold value for the following examples are
the SI value and 10 kine, respectively.
(1) T ≤ t1 (16:04:30) or T < t2 (16:05:00):
The current acceleration data record is updated, with P4 used as the work
page. The trigger conditions are not satisfied.
(2) T = t2 (16:05:00):
Since the SI exceeds the set threshold value (10 kine), the recording trigger
conditions are satisfied. Waveform data with t2 used as the trigger is recorded
for 360 s, and the data is saved.
(3) T = t3: (16:10:30)
Since the recording of waveform data for 360 s has been completed at t3, the
work record area changes to P5, because it has the oldest trigger time, and P4
is retained as recorded waveform data. The header information is also updat-
ed. Since P4 has the newest trigger time, its priority becomes 1 and the rank of
each of the other waveforms is lowered by one.
(4) t3 ≤ T < t4 (16:16:30):
Since, in the waveform data for P5, which has now become the work page, the
SI value exceeds 10 kine at time t3, t3 becomes the trigger point. Also, since
the waveform data before t3 has already been recorded in P4, the 360 s of
waveform data recording starts after trigger point t3.
(5) T = t4:
Since the recording of waveform data for 360 s has been completed at t4, the
work record area changes to P6, and P5 is retained as recorded waveform data.
The header information is also updated. The rank of P5 then becomes 1.
not match the value in the header information.
Therefore, when analyzing the automatically recorded waveform data, it is neces-
sary to check the trigger time in the header information to see whether there are
consecutive waveforms.
6-19
Time (s)
P4 trigger point P5 trigger point

SI value = 10 kine SI value = 32 kine
16:05:00 16:10:30
SI value Trigger threshold = 10 kine

(raw)
(kine)
30s 330s
T T time (s)
360s
t1 t2 t3 t4
=16:04:30
Explanatory diagram for threshold value recording (automatic waveform recording)
Waveform header information (threshold value recording)

P0 Trigger time 4 09:30:17 5 09:30:17 6 09:30:17
P1 Trigger time 3 10:05:42 4 10:05:42 5 10:05:42
P2 Trigger time 2 13:23:00 3 13:23:00 4 13:23:00
P3 Trigger time 1 15:30:02 2 15:30:02 3 15:30:02
P4 Trigger time − Work 1 16:05:00 2 16:05:00
P5 Trigger time 10 06:01:07 − Work 1 16:10:30
P6 Trigger time 9 06:08:12 10 06:08:12 − Work
P7 Trigger time 8 06:23:53 9 06:23:53 10 06:23:53
P8 Trigger time 7 07:08:23 8 07:08:23 9 07:08:23
P9 Trigger time 6 07:26:53 7 07:26:53 8 07:26:53
P10 Trigger time 5 08:23:53 6 08:23:53 7 08:23:53
6-20
Forced waveform recording

Forced waveform recording operates in standby mode to record data for one wave-
form. In forced waveform recording, waveform recording for 360 s is started by the
recording start trigger sent from the loader.
• If the start trigger request is sent again during recording, the waveform
data is recorded again from that point.
Example of waveform recording

The figure below shows waveform data used by a 3-axis exciter in an earthquake
waveform excitation experiment. The earthquake waveform data used for this
experiment comes from an earthquake that occurred in southern Hyogo Prefecture
and was observed at Kobe Marine Meteorological Observatory. The following shows
a waveform graph based on part 360 s of recorded waveform data that was saved to a
file using the loader and then displayed graphically using Microsoft Excel.
Maximum SI value 122.0kine
Maximum synthesized acceleration 878.5Gal
Hyogo Nanbu (southern part of Hyogo Prefecture) earthquake

Waveform observed at Kobe marine observatory
(Hanshin-Awaji (Kobe) Earthquake, 3-axis non-liquefaction waveform) Page 7
X-axis
Y-axis
Z-axis
Acceleration (Gal)
Time (s)
Waveform data recorded in an earthquake waveform excitation experiment
• If a minor failure occurs due to a problem with battery backup, the clock will
stop first as the battery voltage drops when external power is not supplied.
When the power supply is restored, there will be a time lag.
As necessary, check the time on the device.
• If the voltage drops further, either the clock data or the waveform data, or
both, will be lost.
In this case, when the power is restored, the time will be reinitialized (to
00:00:00 on January 1, 2050) and a minor failure state will occur until the
correct date and time are set.
Additionally, if the waveform data is lost, all previously recorded
waveforms will be invalid.
As necessary, check the device time and waveform data.
• The battery is not connected to the earthquake sensor at the time of
shipment from the factory. The time is initialized data and no waveform
data is recorded. Therefore, the unit will be in the minor failure state until
the clock is set using the loader.
• The battery is supplied with the unit. It must be connected before
operating the unit.
6-21
6 - 4 Vibration Detection and Liquefaction Judgment Functions

Vibration detection judgment function
It is possible to set conditions for three vibration detection output relays using AND
and/or OR combinations of four parameters, SI PV value, synthesized AC accelera-
tion PV, JMA seismic intensity PV, and liquefaction. The vibration detection condi-
tions are set using the loader.
Default settings: no conditions are set, and the largest value is the threshold (for
SI value, synthesized AC acceleration, and JMA seismic intensity scale equivalent
value).
When the vibration detection conditions are satisfied, the vibration detection relays
are turned ON.
Sample setting: ‌{(SI PV value) OR (synthesized AC acceleration PV value)} OR
{(JMA seismic intensity PV) AND (liquefaction)}‌
• As shown below, the vibration detection judgment conditions of the SES70
are different from those for the older SES50/51/55/60 models. Be careful
when using the unit without changing the default settings.
Note: ‌Because the vibration detection judgment conditions differ depending
on the user and can be freely changed, no default conditions are set.
(No conditions are specified, and numeric values are fixed at their
maximum.) If vibration detection relays are used, be sure to set the
vibration detection judgment conditions.
SES70 SES50/51/55/60 (old models)
Vibration detection judgment: OR conditions None None
Vibration detection judgment: AND conditions None SI value
Vibration detection judgment: SI value 300 kine 30 kine
Vibration detection judgment: Synthesized acceleration value 4000 Gal 300 Gal
Vibration detection judgment: JMA seismic intensity scale equivalent value 7.9 5.3
Note: By default the same conditions are set for vibration detection judgments 1 to 3.
If the synthesized AC acceleration PV is selected as a vibration detection condition,
the synthesized AC adjusted acceleration value for control (default: 10 Hz) is set to
the PV value in order to eliminate the high-frequency components of acceleration,
which do not affect the amount of building damage.
Default: Synthesized AC adjusted acceleration value for calculation.
Liquefaction judgment function

Soil liquefaction is a phenomenon in which strong earthquake vibration of loose
sandy soil saturated with water in places such as reclaimed land, former river beds,
or coastal plains suddenly turns the ground, which until then was supporting struc-
tures, into something like mud. The ground loses the ability to support structures,
which collapse, causing great damage.
When the liquefaction judgment conditions are satisfied, the liquefaction output
(DO4) turns ON.
The liquefaction judgment function operates not by measuring the underground
water level, but by identifying the characteristic acceleration waveforms associated
with liquefaction. Liquefaction waveforms are identified by the four parameters
listed below.
The liquefaction judgment function can be turned on or off using the loader. By
6-22 default it is ON.
1. SI value: Checks whether the earthquake is sufficient in scale to cause liquefaction.

2. Synthesized
‌ AC acceleration for calculation: Identifies the surface waveform and
liquefaction waveform.
3. Estimated displacement: Checks for amplified displacement due to liquefaction.
4. Zero-cross
‌ period (roughly equal to period÷2): Checks for lengthened accelera-
tion period due to liquefaction.‌
1000
Acceleration [Gal]
500
0
−500 5 10 15 20
−1000
Time [s]
Normal earthquake waveform
400
Acceleration [Gal]
200
0
−200 5 10 15 20
−400
Time [s]
Liquefaction earthquake waveform
6-23
6 - 5 Noise Protection Function

This unit distinguishes intrusive noise, such as electromagnetic or impact waveforms, from acceleration signals, as
shown in the figure below.
If noise occurs, the SI and synthesized AC acceleration values increase and the unit enters the noise protection state,
in which incorrect determinations and incorrect output of the vibration detection judgment and liquefaction judg-
ment are prevented. DO3 (noise protection output) turns ON.
When the noise detection conditions shown below are satisfied, the unit enters the noise protection state. Even if the
noise detection conditions are no longer satisfied, the noise protection state continues for approximately 1 minute,
during which time the vibration detection output and liquefaction output do not turn ON. If the noise protection
state continues for the period of time specified for the noise protection continuous serious failure counter, the status
is determined to be one of serious failure, and the serious failure output turns ON.
In the noise protection state, the minor failure output flashes and the LED also indicates noise protection.
Additionally, the synthesized AC acceleration PV, SI PV, and JMA seismic intensity PV values change to 0 in the
noise protection state, and the liquefaction judgment PV and vibration detection judgment PV turn OFF. However,
the value of the actual output is kept for the hold time (at least 20 s) specified for the output hold process.
6 - 7 Output Functions (P. 6-29)
There are three noise detection methods: single-axis ratio noise detection, other-axis ratio noise detection, and zero-
cross noise detection. Each is described below.
Acceleration A [Gal] Acceleration A [Gal] Acceleration A [Gal]
Time t [s] Time t [s] Time t [s]
Electromagnetic noise (triangular waveform) Electromagnetic noise (square waveform) Impact waveform noise
zz Single-axis ratio noise detection

In this detection method, if the AC acceleration for calculation deflects mostly in
one direction (either positive or negative), which does not normally occur in vibra-
tion waveforms like those of an earthquake, it is judged to be single-axis ratio noise.
Using the loader, an AC acceleration low limit (single-axis ratio noise low limit) can
be set for this function.
Single-axis ratio noise low limit: 1 to 200 Gal
Default: 50 Gal
Setting interval: 1 Gal
zz Other-axis ratio noise detection (ORNP)
In this detection method, if the AC acceleration for calculation for a single axis
becomes large and that of another axis is small, a situation which does not normally
occur in vibration waveforms like those of an earthquake, it is judged to be other-
axis ratio noise.
This function can be enabled or disabled by the loader. An AC acceleration low
limit can be set for this function.
ORNP selection: Enabled/disabled
Default: Enabled
Z: ORNP low limit: 1 to 200 Gal
Default: 100 Gal
X,Y:ORNP low limit: 1 to 200 Gal
Default: 50 Gal
6-24
zz Zero-cross noise detection (ZCN)

In this detection method, if an AC acceleration for calculation having a long period
occurs, which is not normal for vibration waveforms like those of an earthquake, it
is judged to be zero-cross noise.
A zero-cross occurs when the AC acceleration value for calculation changes from
positive to negative, or vice versa. The period between one zero-cross and the next
is the zero-cross noise period.
This function can be enabled or disabled by the loader. If "Enable" is selected, the
zero-cross noise detection (ZCN) time can be set.
ZCN selection
Default: Enable
ZCN time
Default: 20 s
Setting interval: 1 s
Acceleration A [Gal]
Zero-cross noise period
Time t [s]
Zero-cross occurrence
6-25
6 - 6 Error Diagnosis Functions

This unit executes various error diagnoses during operation in order to ensure high reliability.
The diagnosis results can be checked using the serious failure output (DO2), minor failure output (DO1), or LED
indicators on the device. Additionally, error diagnosis details can be checked with the loader.
Failure level Mode
Condition for canceling error
Error Noise de- Measure- Mainte-
Reset Serious Minor Initialize Standby detection state*2
tection ment nance
Watchdog timer error      Mode change to Initialize
Memory error      Mode change to Initialize
A/D converter error      Return of device to normal
Sensor built-in clock error      Mode change to Initialize
Vibration detection output error      Mode change to Initialize
Other H/W errors      Mode change to Initialize or
return of device to normal*3
Accelerometer error  *1  Accelerometer self-diagno-
sis execution
Acceleration error      Return of device to normal
Inclination error (serious)      Return of device to normal
Acceleration noise continuous error      Return of device to normal
Battery level error      Return of device to normal
Temperature error (serious)      Return of device to normal
Sensor built-in clock data error      Return of device to normal
Inclination error (minor)      Return of device to normal
Temperature error (minor)      Return of device to normal
Acceleration noise error      Return of device to normal
*1. In standby mode, error diagnosis of the accelerometer is done using the loader. : Applicable
*2. The table shows the conditions other than recycling the power.
*3. Since other hardware errors have multiple possible causes, the conditions for ending the error detection state vary.
Failure level standards

1. ‌Reset
This is a serious failure that affects all functions.
Operation cannot continue. If this occurs, do a forced reset to change the mode
to initialization mode.
Note: ‌A forced reset is done when this failure occurs, and therefore it is not pos-
sible to check the loader.
2. ‌Serious failure
This failure may affect control output such as vibration detection output and liq-
uefaction detection output.
Serious failure output (DO2) turns ON and minor failure output (DO1) turns
ON or starts flashing. The serious failure LED is also lit. With regard to control
output in the serious failure state, vibration detection output turns OFF, liquefac-
tion output turns OFF, and AO is fixed at 3 mA (about -3 %).
3. ‌Minor failure
This failure does not affect control output, but a check should be made for errors
in waveform recording and clock data storage, as well as clock data errors. The
installation conditions should also be checked.
The minor failure output (DO1) turns ON and the minor failure LED is also lit.
In the minor failure state, the vibration detection output and liquefaction output
continue to operate.
4. ‌Noise detection
A signal other than a vibration waveform has been detected. This may affect the
calculated results.
The noise protection output (DO3) is turns ON, and the LED indicates noise
detection. In the noise protection state, the synthesized AC acceleration PV,
SI PV, and JMA seismic intensity PV are 0. The liquefaction judgment PV and
vibration detection judgment PV turn OFF.
6-26
Diagnostic functions according to the mode

1. I‌ nitialization mode
Errors are detected, except for accelerometer errors. If any serious failure occurs,
the device enters the system error state in standby mode.
‌ easurement mode
2. M
Errors are detected, except for accelerometer errors.
3. S‌ tandby mode
Errors are detected, except for accelerometer errors.
Accelerometer diagnosis can be initiated by a communications command.
4. M
‌ aintenance mode
All diagnoses are possible.
Various error diagnosis functions

1. ‌Watchdog timer function (reset)
The watchdog timer circuit monitors CPU operation to check for problems such
as an infinite loop.
2. ‌Memory error diagnosis function (serious failure)
This diagnostic function monitors the status of the memory device that stores the
settings, waveform records, etc., and detects any errors.
3. ‌A/D converter error diagnosis function (serious failure)
Monitors the status of the A/D converter (which is external to the CPU) and
detects any errors.
4. ‌Sensor built-in clock error diagnosis function (serious failure)
Monitors the status of the clock IC that controls the date and time, and detects
any errors.
5. ‌Vibration detection output error diagnosis function (serious failure)
Unused contacts of the vibration detection output relay are monitored. If the
monitored operation is different from the vibration detection judgment, a vibra-
tion detection output circuit failure is diagnosed.
6. ‌Diagnosis function for other hardware errors (serious failure)
Other hardware errors are detected.
7. ‌Accelerometer error diagnosis function (serious failure)
The diagnostic circuit electrically activates the movable electrode of the acceler-
ometer, which is built into the earthquake sensor for error diagnosis, to detect
operational errors of the accelerometer. Additionally, this function detects errors
in accelerometer adjustment data and output.
8. ‌Inclination error (minor/serious) diagnosis function (minor failure and serious
failure)
The inclination acceleration for the X- and Y-axis is calculated from the mea-
sured acceleration. If it is ±250 Gal or more (approximately 15° or more), there is
considered to be a small inclination and a minor failure state. If the acceleration
exceeds ±500 Gal (approximately 30° or more), there is considered to be a large
inclination and a serious failure state.
9. ‌Acceleration error (serious failure)
The Z-axis inclination acceleration is calculated from the measured acceleration.
If it is ±200 Gal or more, there is an acceleration error and a serious failure.
6-27
10. ‌Diagnosis function for acceleration noise error (noise detection) and accelera-
tion noise continuous error (serious failure) The acceleration is analyzed for
characteristics of non-earthquake waveforms to judge whether or not a failure
has occurred. If this noise error is detected, the unit enters the noise detection
state, and then the noise protection state, in which it is prevented from updat-
ing control outputs such as vibration detection output, liquefaction output, and
analog output. Additionally, if the noise protection state continues for the period
of time that has been preset for the noise protection continuous serious failure
counter, there is considered to be a serious failure. The acceleration noise error
is reset 1 minute after the noise detection has been resolved.
11. ‌Battery level error diagnosis function (serious failure)
Any voltage drop of the battery is analyzed to determine whether an error has
occurred.
12. ‌Temperature error diagnosis function (minor failure and serious failure)
The temperature inside the earthquake sensor is monitored to determine
whether an error has occurred.
13. ‌Sensor built-in clock data error diagnosis function (minor failure)
This diagnosis function detects erroneous data in the device controlling the date
and time.
In checking whether the time has been initialized or is erroneous, if the year is
between 2050 and 2099, the time is judged to be erroneous.
If the clock data backed up by the battery is lost, the unit is initialized to
00:00:00 on January 1, 2050 and the unit enters the minor failure state.
Note that the battery is not connected to the unit before shipment from the
factory. Therefore, the unit has initialized time data and is in the minor failure
state. To reset this minor failure state, set the date and time using the loader.
6-28
6 - 7 Output Functions
Output update and hold processes
After the low cutoff process and hold process are applied to the SI value, synthe-
sized AC acceleration, and JMA seismic intensity scale equivalent value calculation
results, and the hold process is applied to the vibration detection and liquefaction
judgment results, they are reflected by the AO (4–20 mA), relay (1a), and DO4
output (transistor output (Nch open drain)). The minor failure and serious failure
determinations and noise protection are directly reflected by the DO1, DO2, and
DO3 (transistor output (Nch open drain)) outputs.
The outputs are updated at 10 ms intervals.
Synthesized AC Analog Analog Analog

value value value
acceleration PV AO1 (4–20 mA) output
Analog Low cutoff Analog

SI PV value process value
Output
JMA seismic inten- Analog Analog hold AO2 (4–20 mA) output
value value
sity PV process
Vibration detec- ON/OFF ON/OFF Relay (1a) output

tion PV
Liquefaction judg- ON/OFF ON/OFF DO4 (transistor output

ment PV (Nch open drain))
Minor failure judg- ON/OFF DO1 (transistor output

ment result (Nch open drain))
Serious failure ON/OFF DO2 (transistor output

judgment result (Nch open drain))
Noise protection ON/OFF DO3 (transistor output

result (Nch open drain))
Diagram of output functions
Hold process
This process holds the results of the output update process. The hold time can be
set within a range of 20 seconds to 7 days.
If the result of the AO output update process is larger than the current value, peak hold
begins. If the result of the output update process is equivalent to or smaller than the
current value, the status of peak hold is checked. If the peak hold time has ended, it is
updated. If the hold time is continuing, it is not updated.
Hold time re-reset Hold completion
Calculation result hold time
Output update result
Output hold result
Example of calculation result hold process
6-29
For relay output, if the ON/OFF output of DO4 is held “ON,” and the result of the
output update changes from OFF to ON, the hold begins.
Hold time reset Hold time re-reset Hold completion
Judgment result hold time
Judgment result
Judgment hold result
Example of judgment result hold process
Manual output
(1) ‌PV manual output
For the the SI value (PV), synthesized AC acceleration (PV), JMA seismic inten-
sity scale equivalent value (PV), liquefaction judgment (PV), the following val-
ues can be output manually using the loader in standby mode:
SI value (PV): 0 to 300 kine
Synthesized AC acceleration (PV): 0 to 4000 Gal
JMA seismic intensity scale equivalent value (PV): 0 to 7.9
Liquefaction judgment (PV): ON/OFF
Note: ‌Since the PV is manually output, the AO and DO outputs correspond-
ing to the preset PV turn ON. (For example, the vibration detection
relay turns ON/OFF in connection with the vibration detection judg-
ment threshold value.)
(2) ‌AO/DO manual output
For the AO outputs of the SI value, synthesized AC acceleration, JMA seismic
intensity scale equivalent value, the relay outputs (1, 2, 3) of the vibration detec-
tion judgment, the liquefaction judgment DO3 output, the minor failure DO1
output and serious failure DO2 output, the following values can be output man-
ually using the loader in standby mode:
AO output: 0 to 100% (4–20 mA) output variable change
Relay output: ON/OFF variable change
DO3 output: ON/OFF variable change
DO4 output: ON/OFF/blinking variable change
DO1 output: ON/OFF/blinking variable change
DO2 output: ON/OFF variable change
Note: ‌An internal judgment is set for DO outputs. Accordingly, if negative
logic is chosen for the minor failure output (DO1), serious failure out-
put (DO2), and noise protection output (DO3), the settings will differ
from the actual DO terminal status.
6-30
Output adjustment (constant drift)

Constant drift of the AO output or vibration detection output can have four pos-
sible causes:
(1) Constant interfering vibration
(2) Constant electrical or electromagnetic field noise
(3) Sensor internal circuit noise
(4) AO output circuit drift (0.3 % FS max.)
Before adjusting the output, take corrective measures against causes (1) and (2)
above, such as changing the installation location and ambient environment condi-
tions.
zz PV bias
Setting a negative bias for the SI raw value and synthesized acceleration raw value is
effective for causes (1) to (3) above.
However, a negative value of less than 4 mA may be output. Additionally, since the
measured value will be small when there is no noise or interference, the AO output
will be small, and the vibration detection output may not turn ON. Both of the
default settings are 0.
zz PV low cutoff
Setting a low cutoff for the SI PV, synthesized acceleration PV, and JMA seismic
intensity PV is effective for causes (1) to (3) above.
However, if the measured value is less than the preset low cutoff value, the AO out-
put will be 0 % and the vibration detection output will be OFF. The default settings
are shown below.
Default
SI PV Low Cutoff 1.0 kine
Synth. Accel. PV Low Cutoff 5.0 Gal
M.V.E.V. (JMA) PV Low Cutoff 1.0.
Note: ‌The default settings are different from those of the SES60. All default settings of the
SES60 are 0.
zz AO bias
By adjusting the bias for drift (0.3 % FS max.) of the analog output circuit, which is
cause (4) above, constant drift error can be reduced.
To eliminate causes (1) to (3), make the adjustment in the manual output state.
Output adjustment (high-frequency noise)

To eliminate the adverse effects of the high-frequency component of acceleration, it
is effective to use the acceleration value for control, with a low cutoff frequency for
the acceleration filter.
6 - 2 Internal Calculation Processes (P. 6-7).
Set the synthesized AC acceleration PV to the synthesized AC adjusted acceleration
value for control. If any adverse effect is found even with this setting, decrease the
cutoff frequency of the acceleration filter for control.
Default: 10 Hz
6-31
Output selection
SES70 output function or SES60-compatible output functions can be selected with
the loader.
The SES60-compatible output function is used to make the following revised SES70
output functions the same as those of the SES60.
SES70 output function SES60-compatible output function
Vibration detection judgment Vibration detection judgment 1, 2, 3 Vibration detection judgment 1 only
Vibration detection output Vibration detection outputs 1, 2, 3 Vibration detection output 1 only
Minor failure output function* For Present/Minor For Present/Noise/Minor
Noise protection output (DO3) ON OFF
Maintenance sequence Phases 1–3 Phase 1 only
*‌In the minor failure output function, functions used for Present/Minor will just
change to those used for Present/Noise/Minor. The selection of settings will not
automatically change. (For example, a function exclusively used for Minor will not
automatically change to a function used for Present/Minor.) If necessary, change
the selection of settings.
Note: ‌Only by applying the SES60-compatible output function to the output func-
tion selection, the SES70 cannot do the same operations as the SES60.
If necessary, change the following. The table below shows the comparison of
default settings. If default settings are modified, change them as needed.
SES70 output SES60-compatible output
Vibration detection judgment: OR conditions None SI Value
Vibration detection judgment: AND conditions None None
Vibration detection judgment: SI value 300 kine 30 kine
Vibration detection judgment: Synthesized acceleration value 4000 Gal 300 Gal
Vibration detection judgment: J MA seismic intensity scale 7.9 5.3
equivalent value
Waveform recording Threshold value Maximum value recording with
recording trigger update
Value used for the maximum value recording with trigger SI value SI value
update
Value used for the maximum value recording without trigger SI value No function
update
Value used for the threshold value recording SI value SI value
Threshold: SI Value 1 kine 30 kine
Threshold: Synthesized acceleration 5 Gal 300 Gal
Threshold: JMA seismic intensity scale equivalent value 1.0 5.3
RS-485 transmission speed 38400 bps 19200 bps
Minor failure output (DO1) function selection Positive logic value: Positive logic value: For Present/
For Present/Minor Minor joint use (in terms of functions,
acts as Present/Noise/Minor)
Serious failure output (DO1) function selection Positive logic Positive logic
SI PV Low Cutoff 1.0 kine 0.0 kine
Synth. Accel. PV Low Cutoff 5.0 Gal 0.0 Gal
M.V.E.V. (JMA) PV Low Cutoff 1.0. 0.0
6-32
Outputs according to mode

The various outputs have different output result processing depending upon which
of the four modes the unit is in, and the unit's operating state. For the output in
each mode, the operation described in the lowest row of the "Operating state" col-
umn has priority.
Synthesized AC ac-
Vibration de- Liquefaction celeration, SI value, Noise
Minor failure Serious failure
Mode Operating state tection output detection JMA seismic intensity protection
output (DO1) output (DO2)
(relays 1, 2, 3) output (DO4) scale equivalent value output (DO3)
(AO1, 2)
Initialization Normal operation OFF Fast ON/ OFF OFF
OFF*1
Measurement Normal operation Hold process output OFF OFF OFF
During minor failure ON
During noise protection Noise + hold process output OFF ON
During serious failure OFF fixed value Approx. 3.5 mA ON ON OFF
Standby Normal operation Hold process output Slow ON/ OFF OFF
During minor failure OFF*2
During noise protection Noise + hold process output ON
During serious failure OFF Approx. 3.5 mA ON OFF
During system error
Manual output Manual output
Maintenance Normal operation Maintenance sequence output
*1. Fast ON/OFF: 0.5 s / 0.5 s
*2. Slow ON/OFF: 0.1 s/0.1 s
Note: ‌‌For the output in each mode, the operation described in the lowest row of the "Operating state" column has priority.
Failure output conditions
Minor failure: Positive logic, shared output
Serious failure: Positive logic
Noise protection: Positive logic
• Take into account that analog output may fluctuate if the power increases
slowly during startup.
6-33
6 - 8 Maintenance Sequence
By switching to maintenance mode using diagnosis input (DI1) or the loader, the operation of the outputs and accel-
erometer can be checked. The following describes the maintenance sequence for checking output operation.
Maintenance sequence
zz Mode change to maintenance mode
(1) ‌In measurement mode, when the DI1 is ON continuously for 2 s or longer, or
when a mode transition request from the loader or RS-485 is received, the mode
changes to maintenance mode.
Phase 1
(2) ‌The DO1 minor failure output becomes a slow ON/OFF (0.5 s/0.5 s) and the
AO1 and 2 outputs become 100 % (20 mA) outputs.‌
(3) After 1 s has elapsed, the DO2 serious failure output is turned ON.
(4) After another 1 s has elapsed, the vibration detection output is turned ON.
(5) ‌The diagnosis of the accelerometer starts 30 s after the mode changes to mainte-
nance mode.‌
(6) ‌When the diagnosis of the accelerometer has been completed, the DO1 minor
failure output starts flashing, the DO2 serious failure output is turned OFF, the
AO1 and 2 outputs change to 0 % (4 mA), and the DO4 liquefaction output
enters the slow ON/OFF status.‌(The vibration detection output remains ON.)
Phase 2
(7) ‌If the DI1 input remains ON for 2 s or longer, or if a diagnostic phase change
request from the loader or RS-485 is received, vibration detection output 1 and
the DO4 liquefaction output are turned OFF, the DO1 minor failure enters the
slow ON/OFF status, and the AO1 and 2 outputs change to 50 % (12 mA).‌
(8) One second later, the DO2 is turned ON.‌
(9) After another second, vibration detection output 2 is turned ON.‌
(10) ‌Then, 28 seconds later, the DO1 minor failure output starts flashing, the DO2
serious failure output is turned OFF, the AO1 and 2 outputs change to 0 % (4
mA).‌(Vibration detection output 2 remains ON.)
Phase 3
(11) ‌If the DI1 input remains ON for 2 s or longer, or if a diagnostic phase change
request from the loader or RS-485 is received, vibration detection output 2 is
turned OFF, the DO1 minor failure output enters the slow ON/OFF status, and
the AO1 and 2 outputs change to 10 % (5.6 mA).‌
(12) ‌Two seconds later, vibration detection output 3 is turned ON.‌
(13) ‌Then, 28 seconds later, vibration detection output 3 is turned OFF, the DO1
minor failure output starts flashing, the DO3 noise protection output is turned
ON, and the AO1 and 2 outputs change to 0 % (4 mA).‌
After completion of phase 3
6-34
(14) Under
‌ these circumstances, if the DI1 input remains ON for 2 s or longer,
or when a mode change request from the loader or RS-485 is received, the
mode changes to initialization mode, the DO1 minor failure output enters
the fast ON/OFF status, and the DO3 noise protection output is turned OFF.
(Maintenance mode ends.)
(15) In
‌ step 13, if there is no mode change request for 20 minutes (timeout period),
the mode changes to initialization mode. (Maintenance
‌ mode ends.)
Time-out: 20 min (if communication is received during this time,

20-min count restarts after communication ends)
2s Reception of diagnosis 2s Reception of diagnostic 2s Reception of diagnostic 2s Reception of diagnosis

OFFstart signal
phase transition start signal phase transition start signal completion signal
Diagnostic input from DI1 ON
or communications
Internal diagnosis completion
30s 30s 30s
Flashing Flashing Flashing Fast ON/OFF or OFF
Minor failure output (DO1)
Slow ON/OFF Slow ON/OFF Slow ON/OFF
1s 1s
Serious failure output (DO2)
Noise protection output (DO3)

2s
Vibration detection output 1
2s

2s
Slow ON/OFF
Liquefaction detection output (DO4)
100% 0% 50% 0% 10% 0%

Analog output (AO1, 2)
Liquefaction detection output
Phase 1 Phase 2 Phase 3
Measurement mode Maintenance mode Initialization mode
Slow ON/OFF: 0.5 s / 0.5 s

Fast ON/OFF: 0.1 s / 0.1 s
Flashing: ON/OFF/ON/OFF/ON/OFF (0.1 s / 0.1 s / 0.1 s / 0.1 s / 0.1 s / 0.5 s)
Maintenance sequence diagram
6-35
6 - 9 LED Output Functions

Four LEDs indicate the mode and error status.
In initialization mode, as shown in the table below, the LED indication automatically changes in the order shown,
beginning from the top row.
LED1: Minor failure
LED2: Serious failure
LED3: Noise protection
LED4: Operation mode
Minor Serious
Noise Mode
failure failure
Mode Status LED 3 LED 4
LED 1 LED 2
(red) (green)
(red) (red)
Initialization mode Any status    
   
   
Measurement mode No error    
Minor failure    
Serious failure    
Protection    
Minor & serious failure & protection    
Maintenance mode (phase 1) 30 s after the mode transition    
After 30 s    
Maintenance mode (phase 2) 30 s after the transition to phase 2    
After 30 s    
Maintenance mode (phase 3) 30 s after the transition to phase 3    
After 30 s    
Standby mode No error    
Minor failure    
Serious failure    
Protection    
Minor & serious failure & protection    
: ON,  : Fast blinking, : Slow blinking, : Flashing, : OFF
Slow ON/OFF (0.5 s / 0.5 s)
Fast ON/OFF (0.1 s / 0.1 s)
Flashing: ON/OFF/ON/OFF/ON/OFF (0.5 s/0.1s/0.1 s/0.1s/0.1 s/0.1 s)
LED 3 (red)
LED 2 (red)
LED 1 (red)
LED 4 (green)
6-36
Real-time data monitoring data

It is possible to read and write the internal data from the earthquake sensor using
the SLP-SE7 Smart Loader Package for the Intelligent Earthquake Sensor, which
runs on a personal computer.
However, note that the details of this chapter may differ from the actual specifica-
tions of the loader.
SLP-SE7 Smart Loader Package for SES70 Intelligent Earthquake Sensor, No.
CP-UM-5756E
zz Monitoring data
The following data can be read in real time on the PC monitor:
• Operation mode
• Errors details
• SI PV
• Synthesized acceleration PV
• JMA seismic intensity scale equivalent PV
• AC acceleration (X-, Y-, and Z-axis) for operation and control
• Minor failure output (DO1)
• Serious failure output (DO2)
• Noise protection output (DO3)
• Vibration detection output (relay) 1, 2, 3
• Liquefaction detection output (DO4)
• Sensor built-in clock
• AO1, AO2
• Earthquake sensor model number, etc.
zz Trend monitoring screen
On the trend monitoring screen of the real-time monitor, graphs for SI PV, synthe-
sized acceleration PV, adjusted acceleration value for calculation, AC acceleration
for calculation, and inclination acceleration value for calculation can be displayed.
7-1
zz Detailed error data

Detailed information on detected errors, such as serious failure, noise detection,
and minor failure, is summarized by error level, and is reflected in the general error
information.
Error level
Error
Serious failure Minor failure Noise detection
Memory error ●
A/D converter error ●
Sensor built-in clock error ●
Vibration detection output error ●
Other hardware error ●
Accelerometer error ●
Acceleration error ●
Inclination error (serious) ●
Acceleration noise continuous error ●
Battery level error ●
Temperature error (serious) ●
Temperature error (minor) ●
Sensor built-in clock data error ●
Inclination error (minor) ●
Acceleration noise error ●
With regard to detailed error information, it is possible to switch between current

errors and errors that occurred previously during operation and were stored.
• To clear the stored information, reset the power or change the mode
from standby mode to initialization mode.
Changing of settings
The following earthquake sensor settings can be changed:
zz Date and time setting
The date and time of the earthquake sensor's built-in clock can be set.
There are two methods of setting: directly inputting numeric values and synchro-
nizing the date and time with the clock of the personal computer using the loader.
If the clock data is faulty, the unit enters the minor failure status.
Initial value: 00:00:00 on January 1, 2050.
zz SI type
SI 1 or SI 2 can be chosen.
SI 1: 7 natural periods, vector projection in 8 directions
SI 2: 24 natural periods, vector projection in 16 directions
Default SI type: SI 1
zz Synthesized acceleration type
The synthesized AC acceleration PV value is selected from the synthesized AC
acceleration for calculation and the synthesized AC acceleration for control.
Default: AC acceleration for control
zz Number of synthesized AC acceleration operation axes for calculation and control
The synthesized axes of the synthesized AC acceleration for calculation and control
are chosen from the 2-axis horizontal plane (X and Y) or 3 axes.
Default: 2 axes for calculation, 3 axes for control.
7-2
zz JMA seismic intensity scale calculation method selection

Either of two calculation methods can be chosen, that is, calculation using the SI
PV only or using the SI PV and synthesized AC acceleration. The default setting is
the equation that uses SI PV and synthesized AC acceleration.
zz Vibration detection judgment setting
Three vibration detection judgment conditions (J.V.D.1, J.V.D.2, J.V.D.3) can be set.
Logical operations for the SI value, synthesized AC acceleration, JMA seismic
intensity scale equivalent value, and liquefaction judgment value to turn ON or
OFF the vibration detection output can be selected for vibration detection judg-
ment conditions. Threshold values for the SI value, synthesized AC acceleration,
and JMA seismic intensity scale equivalent value, which are used for vibration
detection judgment, can be set.
Item name Setting Default *
The logical sum of the AND condition and the OR condition AND condition: none
Vibration detection judgment 1 AND condition
Vibration detection judgment 1 OR conditionis used as the vibration detection judgment condition. OR condition: none
Note that both the AND and OR conditions cannot be set
for the same target item.
AND condition: ‌The AND condition for the set target item
is used as the judgment condition.
OR condition: ‌The OR condition for the set target item is
used as the judgment condition.
Vibration detection judgment 1 SI value 1–300 kine 300 kine
Vibration detection judgment 1 synthesized 5–4000 Gal 400 Gal
AC acceleration value
Vibration detection judgment 1 JMA seis- 1.0–7.9 7.9
mic intensity scale equivalent value
Note: The above settings also apply to vibration detection judgments 2 and 3.
* ‌The default vibration detection judgment settings for the SES70 differ from those of SES60.
 Vibration detection judgment function (P. 6-22)
zz Output hold time setting

Hold time values can be set for the control outputs, such as vibration detection out-
put (relay), liquefaction output (DO4), SI value, synthesized AC acceleration, and
JMA seismic intensity scale equivalent value (AO1, 2).
Item name Setting Default
Vibration detection output (relay output) hold time 20–604800 s 20 s
Liquefaction detection output (DO4 output) hold time (1 week max.)
AO output (AO1 and AO2) hold time
zz AO span selection
Span allocation of 0–100 % (4–20 mA) for the SI value, synthesized AC acceleration
value, and JMA seismic intensity scale equivalent value output (AO1, 2) can be changed.
SI value AO span 50, 100, 150, or 200 kine/20 mA 200 kine
Synthesized AC acceleration AO span 500, 1000, 2000, or 3000 Gal/20mA 2000 Gal
JMA seismic intensity scale AO span 5.0 or 8.0/20 mA 8.0
Note: In addition to selection, direct input of one of the 4 numeric values is possible.
zz AO output selection
The output of AO1 and AO2 can be selected.
AO1 selection Synthesized AC acceleration PV, SI PV, or JMA seismic intensity Synthesized AC acceleration PV
AO2 selection scale PV SI PV
7-3
zz PV bias
A bias calculation can be applied to the SI PV, synthesized AC acceleration PV, and
JMA seismic intensity scale PV.
SI PV bias -30.0 to +30.0 kine 0.0 kine
Synthesized AC acceleration PV bias -400.0 to +400.0 Gal 0 Gal
JMA seismic intensity scale PV bias -3.0 to +3.0 0
zz PV low-cut
A low cutoff can be set for the SI PV, synthesized AC acceleration PV, and JMA seis-
mic intensity scale PV.
SI PV low-cut 0.0 to 30.0 kine 1.0 kine
Synthesized AC acceleration PV low cutoff 0.0 to 400.0 Gal 5.0 Gal
JMA seismic intensity scale PV low cutoff 0.0 to 3.0 1.0
Note: ‌The default settings of the SES70 are different from those of the SES60.
All of the 3 settings for SES60 are 0.
zz AO ratio
The ramp for the analog output can be adjusted.
AO1 ratio 0.900–1.100 1.000
AO2 ratio
zz AO bias
The drift for the analog output can be adjusted.
AO1 bias -5.0 to +5.0 % 0.0 %
AO2 bias
zz Noise protection continuous serious failure judgment time

It is possible to set a time required to judge serious failure caused by continuous
noise protection.
Setting: 5–10080 min
Default: 30 min
zz Noise protection low limit
Noise protection works using multiple logical processes. One logical process deter-
mines noise if the AC acceleration deflects largely in one direction, either positive
or negative. This logical process determines the AC acceleration low limit.
Single axis ratio NP lower limit: 1–200 Gal
Default: 50 Gal
Another logical process determines noise when the AC acceleration deflects largely
along a certain axis (X, Y, or Z), in either positive or negative directions, but deflec-
tion on other axes is small. Whether to use this logical process can be selected. In
addition, the AC acceleration low limit when the logical process will be used can be set.
Other-axis ratio NP selection: Enable/Disable
Default: Enable
Z: Other-axis ratio NP lower limit: 1–200 Gal
Default: 100 Gal
X,Y: Other-axis ratio NP lower limit: 1–200 Gal
Default: 50 Gal
7-4
zz Zero-cross noise detection selection

Zero-cross noise detection can be enabled or disabled. If this function is enabled, a
zero-cross period can be set.
Default: Enabled
Zero-cross period: 20 s
zz Minor failure output function (DO1) selection
The minor failure output (DO1) can be set to "Present/Minor (minor failure,
mode)" or "Minor."
Outputs according to mode (P. 6-33)
Default: Present/Minor, positive logic
zz Serious failure output (DO2) logic selection
The serious failure output (DO2) logic can be set to positive or negative logic.
Default: Positive logic
zz Noise output (DO3) logic selection
The noise output (DO3) logic can be set to positive or negative logic.
Default: Positive logic
zz Communication settings
The station address, RS-485, data format (parity check), baud rate, etc. can be set.
The data format is fixed at 8-bit data and 1 stop bit. For parity check only, "None" or
"Even" can be chosen.
Station address 0–126 1
RS-485 data format (parity) None or even Even parity
RS-485 baud rate 9600, 9200, or 38400 bps 38400 bps
zz Liquefaction detection enable/disable setting

The liquefaction output can be enabled or disabled.
Default: Enable
zz Restoring default settings
It is possible to reset the settings to the factory defaults.
Settings other than communication settings will be initialized to the default set-
tings. All history records (such as waveforms) are deleted.
zz Acceleration filter setting
The user can set a cutoff frequency for the low-pass filter that separates the X-, Y-,
and Z-axis acceleration signal from the acceleration for calculation and acceleration
for control. A cutoff frequency can be set for both the acceleration for calculation
and acceleration for control.
Default: 30 Hz for calculation, 10 Hz for control.
zz Output function selection
Either the SES70 output function or the SES60-compatible output function can be
chosen.
The SES60-compatible output function is used to make the necessary changes in the
SES70 output functions so that the SES70 has the same outputs as those of the SES60.
 Output selection (P. 6-32)
Default: SES70 output function
7-5
Waveform recording
Using the loader, the recorded waveform data can be read out or deleted, and
forced waveform recording can also be executed.
zz Readout of recorded waveform data list
The header data (time stamp, SI value, synthesized AC acceleration, JMA seismic
intensity scale equivalent value, and error flag, etc.) of the recorded waveform data
can be read.
zz Readout of recorded waveform data
Ten automatically recorded waveform records and one forced waveform recording
can be read. The acceleration numeric values can also be displayed and graphed.
zz File saving
The waveforms with their header data can be read and then saved to a file for anal-
ysis. At the same time, the configuration file is also saved.
zz Forced waveform recording
Forced waveform recording can be started using the loader in standby mode.
zz Waveform deletion
Data for ten automatic waveform recordings and one forced waveform recording
can be deleted.
zz Automatic waveform recording conditions
The user can select either maximum value with/without trigger update or threshold
value as the criterion for recording. Additionally, the threshold value parameters
can be set.
Manual output function

Each output can be set manually using the loader in standby mode. There are two
manual output types as follows:
• PV manual output
• AO/DO manual output
zz PV manual output
The following are manually output PVs.
• SI PV
• Synthesized acceleration PV
• JMA seismic intensity scale PV
• Liquefaction judgment PV
Since PVs are manually output, the related AO and DO outputs also turn ON/OFF.
(For example, the vibration detection output relay turns ON/OFF in conjunction
with the vibration detection judgment threshold.)
Item name Setting Initial value Setting interval
SI PV 0–300 kine * 1 kine
Synthesized AC acceleration PV 0–4000 * 1 Gal
JMA seismic intensity scale PV 0–7.9 * 0.1
Liquefaction judgment PV Enable/Disable * ー
* ‌Initial value refers to the output value set at the time when PV manual output was set
for the manual output selection.
7-6
zz AO/DO manual output

The following AO, DO, and relay outputs are manually output:
• AO1 manual output
• AO2 manual output
• Vibration detection output 1, 2, 3
• Minor failure output (DO1)
• Serious failure output (DO2)
• Noise protection output (DO3)
• Liquefaction detection output (DO4)
AO manual output
AO1 manual output -10.0 to 110.0 % * 0.1%
AO2 manual output -10.0 to 110.0 % * 0.1%
* ‌Initial value refers to the output value set at the time when AO/DO manual output was
set for the manual output selection.
Vibration detection output
Vibration detection output 1 ON/OFF * -
* ‌Initial value refers to the output value set at the time when AO/DO manual output was
set for the manual output selection.
DO output
Minor failure output (DO1) ON/OFF/blinking *1 -
Serious failure output (DO2) ON/OFF *1 -
Noise protection output (DO3) ON/OFF *1 -
Liquefaction detection output (DO4) ON/OFF/blinking*2 *1 -
*1. ‌Note: Initial value refers to the output value set at the time when AO/DO manual out-
put was set for the manual output selection.
*2. The terminal's status is slow ON/OFF.
• An
‌ internal judgment is set for DO outputs. Accordingly, if negative logic is chosen
for the minor failure output (DO1), serious failure output (DO2), or noise protec-
tion output (DO3), the settings will differ from the actual DO terminal status. The
table below shows the relationship of the settings and the actual terminal status.
SES70 terminal status
Item Manual output setting
With positive logic With negative logic
Minor failure OFF OFF ON
ON ON OFF
Blinking Slow ON/OFF Slow ON/OFF
Serious failure OFF OFF ON
ON ON OFF
Noise protection OFF OFF ON
ON ON OFF
7-7
Diagnosis and adjustment function

Bias adjustment and diagnosis of the accelerometer can be executed using the
loader in standby mode.
zz Zero adjustment
The bias is adjusted automatically so that the adjusted acceleration value is close to
0 Gal.
This adjustment is possible only when the adjusted acceleration value is within a
range of ±150 Gal.
zz Accelerometer diagnosis function
When the diagnosis operation starts, the diagnostic circuit moves the accelerom-
eter physically. The output operation can be checked to display the results of diag-
nosis.
Before starting the diagnosis, check that the sensor is installed on a plane that is
horizontal to ±3° or less.
7-8
WARNING
When there might be an explosive atmosphere, do not open the cover.
When discarding the battery, do not throw it into the fire. Doing so may cause it to explode.
Checklist for periodic inspection

Check the following regularly:
• The case, cover, and cable gland are not damaged.
• The cable gland and cover are not loose.
• The terminal screws are not loose.
• The O-ring attached to the cover is not damaged.
• The reference plane is level within ±3°.
How to replace the battery

After checking that the workplace is a non-hazardous area, follow the steps below to
replace the battery.
(1) Turn OFF the power source.
(2) Remove the cover and connect the new battery to the empty connector.
(3) Remove the old battery and insert the new one into the battery holder.
(4) ‌Turn ON the power and then check that the minor failure (battery error) indica-
tion is OFF.
(5) Put the cover back on the unit.
(6) ‌Using the loader, check the sensor clock time. If necessary, set the time.
• Since the unit has no secondary battery backup function, be sure to connect
a battery to the unit.
• When using the battery, strictly observe the following cautions.
Failure to observe the following warnings may lead to battery overheating,
rupture or leakage.
• ‌Do not use batteries that have a damaged surface, liquid leakage, or other
abnormal condition.
• ‌Batteries should not be thrown into the fire, recharged, short-circuited,
disassembled, or heated.
• ‌If possible, store batteries in a cool dry place at storage temperature.
• Always install the battery immediately before starting operation of the
earthquake sensor. The battery will run down while the sensor is not turned
on. Installing it prematurely might shorten its service life during actual
operation.
8-1
Troubleshooting
If this unit does not work or malfunctions, check the following:
• Is the wiring loose or disconnected?
• Are the supply power and load resistance correct?
• Is faulty output being generated?
Also check the following using the loader (sold separately):
• Is the acceleration or SI value abnormal?
• Is an internal error displayed on the detailed error screen?
• Is manual output selected?
zz Corrective actions to be taken after checking the detailed error information on the loader
Detailed error information Description Countermeasures
Memory error (serious failure) Memory data or memory After checking the details of the current error, reset the power.
readout is faulty. Recorded waveform data may be deleted.
If the same error occurs again, contact the azbil Group or one of
its sales representatives.
A/D converter error (serious A/D converter is faulty. After checking the details of the current error, reset the power.
failure) If the same error occurs again, contact the azbil Group or one of
Sensor built-in clock error Built-in clock operation is
(serious failure) faulty.
Vibration detection output Vibration detection out- An error has occurred in the vibration detection output circuit of
error (serious failure) put circuit is faulty. the sensor.
Replace the sensor with a new one.
Other hardware error (serious Other H/W error After checking the details of the current error, reset the power.
failure) If the same error occurs again, contact the azbil Group or one of
Accelerometer error (serious Accelerometer is faulty. After checking the details of the current error, reset the power.
failure) Run the accelerometer diagnosis.
Acceleration error (serious Detected acceleration After checking the details of the current error and sensor installa-
error) value is faulty. tion conditions, reset the power.
Inclination error (serious) Sensor is not level.
(serious error)
Acceleration noise continuous Non-earthquake wave- After checking the details of the current error, reset the power.
error (serious error) form continues abnor- If the same error occurs again, contact the azbil Group or one of
mally. its sales representatives.
Battery level error (minor error) Battery voltage drops. Replace the sensor's built-in battery with a new one.
 How to replace the battery (P. 8-1)
Temperature error (minor Internal temperature of Turn OFF the power. After checking that the ambient temperature
failure/serious failure) the sensor is abnormal. is correct, turn ON the power again.
Sensor built-in clock time Built-in clock time is Set the sensor built-in clock to the correct time.
error (minor failure) incorrect. If the same error occurs again, contact the azbil Group or one of
Inclination error (minor) Sensor is not level. After checking the details of the current error and sensor installa-
(minor failure) tion conditions, reset the power.
Acceleration noise error (noise Non-earthquake wave- Wait for a period of time set for the noise protection continuous
detection) form detection is faulty. serious failure (initial value is 5 min).
If the error is not cleared or if the same error occurs frequently,
contact the azbil Group or one of its sales representatives.
8-2
Chapter 9. DISPOSAL
When discarding this device, dispose of it properly as industrial waste, following local regulations.
WARNING
When discarding the battery, do not throw it into the fire. Doing so may cause it to explode.
CAUTION
Dispose of used batteries appropriately according to local regulations.
9-1
Memo
10 - 1 Specifications
Item Description
Basic Explosion-proof standard Exd II BT 4 (TIIS pressure-resistant explosion-proof construction)
specifications Rated acceleration range ±2000 Gal (in x, y, and z directions)
Acceleration measurement ±2200 Gal (in x, y, and z directions)
range
Acceleration measurement 1 Gal (for DC acceleration measurement)
resolution
FSG sensitivity ±2 %FSG (±980 Gal)*1 in x, y, and z directions
FSG middle point ±3 %FSG (±980 Gal)*1 in x, y, and z directions
Output linearity ±2 %FSO (+2000 Gal), ± 2 %FSO (−2000 Gal)*1 in x, y, and z directions
Sensitivity in other axial ±3 % in x, y, and z directions
directions
Electrical noise 2 Gal (acceleration filter: 30 Hz) in x, y, and z directions
Acceleration sampling 10 ms sampling
Acceleration waveform 10 ms sampling for 360 s, waveforms in x, y, and z directions, 10 waveforms
recording
Electrical Rated voltage 12 V DC ±10 % or 24 V DC ±10 %
specifications Current consumption 500/260 mA (12/24 V DC)
Power ON inrush current 30 A/500 μs max.
Contact output (vibration Relay 1a
detection outputs 1 to 3)
Digital output 1 (minor failure Transistor output (Nch open drain) (ON in case of a minor failure, ON/OFF action
detection output) in any mode other than measurement mode)
Digital output 2 (serious Transistor output (Nch open drain) (default setting: ON in case of a serious
failure detection output) failure)
Digital output 3 (noise Transistor output (Nch open drain) (default setting: ON in case of noise
protection output) protection detection)
Digital output 4 (liquefaction Transistor output (Nch open drain) (ON in case of liquefaction detection output)
detection output)
Analog output 1 *2 4–20 mA current source (default setting: synthesized AC acceleration = 0 to
2000 Gal)
Analog output 2 *2 4–20 mA current source (default setting: SI value = 0 to 200 kine)
Analog output load resistance 300 Ω max.
Digital input (diagnostic Photocoupler input current source
input)
Dielectric Strength 500 V AC for 1 min or 600 V AC for 1 s
Insulation Resistance 100 MΩ with 500 V DC megger
Mechanical Material Case and cover: aluminum alloy casting
specifications Mounting angle Within ±3˚ from horizontal
Cable gland type G3/4 flameproof packing
Mass 1.9 kg
Environmental Operating temperature Ambient temperature: −10 to +60 ˚C (without freezing)
specifications Guaranteed accuracy Ambient temperature: 0 to +50 ˚C (without freezing)
temperature
Storage temperature −20 to +70 ˚C
Operating humidity 90 %RH max. (without condensation)
Waterproofing and dust- IP67 (1 m under water for 30 min), JIS C0920 watertight (except for metal cable
proofing pipe part)*3
Vibration resistance 19.6 m/s2 max.
Shock resistance 490 m/s2 max.
10-1
Item Description
Accessories 2 sets of flameproof packing (different types)
Flameproof packing (1) and washers (2) for 10 to 12 mm outer diameter cable
Flameproof packing (1) and washers (2) for 12 to 14 mm outer diameter cable
Cable gland set (cable gland, cable clamp, lock nut)
Battery (life: 10 years min. when power is supplied, 6 months when no power is
supplied, at 20 ˚C)
3 hexagon socket bolts (M6×10 mm)
Cross-slot head screws with captive washer (3 each of M5×30 mm and
M5×20 mm)
User's manual, No. CP-SP-1393E
Accessories (sold separately) Smart Loader Package (SLP-SE7)
Replacement Replacement battery Part No.: 81446431-001
parts Manufacturer: Azbil Corporation
Electrochemical: Manganese dioxide lithium battery
Nominal voltage: 3 V
Rated capacity: 240 mAh
Maintenance parts set for Part No.: 81447670-001
SES70 Manufacturer: Azbil Corporation
Includes: a cable gland and an O-ring
*1. Measurement conditions
Supply voltage: 12 or 24 V DC ±10 %
• Ambient temperature: 0 to 50 ˚C
• Humidity: 50 ±20 %RH
*2. SI value, synthesized AC acceleration, or JMA seismic intensity scale
*3. Waterproofing and dust-proofing are not tested by TIIS.
10-2
10 - 2 Performance Specifications
Item Description
PV*1 Synthesized AC acceleration 0 to 4000 Gal
measurement range
SI measurement range 0 to 300 kine
Measurement range of JMA seismic 0 to 7.9
intensity scale equivalent value
Analog Output type 4–20 mA current source DC output, without isolation
output*2 D/A conversion method Conversion by PWM, period = 2.05 ms (488 Hz)
Allowable load resistance 300 Ω max.
Output accuracy ±0.2 %FS (0 to 50 °C)
Output resolution 14 bits
Open terminal voltage 26.4 V DC max.
Max. output current 21.6 mA
Min. output current 2.4 mA DC
Output update cycle 10 ms
Output response time 150 ms
Output hold The maximum value is held for the preset peak hold time. (The hold time can
be set using the loader. Initial value: 20 s)
Vibration No. of relays 3
detection Contact arrangement 1a contact relay output
output
Contact rating 30 V DC, 0.5 A max., resistive load (a 100 V AC line cannot be connected)
(relay)*3
Vibration detection setting The vibration detection threshold can be set to SI value, synthesized AC
acceleration, or JMA seismic intensity scale equivalent value
Vibration detection conditions It is possible to make combinations with AND and OR of four conditions:
SI value, synthesized AC acceleration, JMA seismic intensity scale equivalent
value, and liquefaction. (Default: None of the four items or AND or OR
conditions are enabled for vibration detection judgments 1, 2, or 3.)
Default setting The maximum possible values are as follows:
SI value: 300 kine
Synthesized acceleration: 4000 Gal
JMA seismic intensity scale equivalent value: 7.9
Output hold ON output is held for the preset hold time. (The hold time can be set using
the loader. Initial value is 20 s.)
Open collector Output type Transistor output (Nch open drain)
outputs Dielectric strength of output 30 V DC
(DO1 to 4)*4
Max. output current 50 mA DC
OFF-state leakage current 100 μA DC max.
ON residual voltage 0.5 V DC max.
Output short-circuit protection Built-in protective circuit
Digital input Compatible output types Non-voltage contacts (relay, mechanical switch), open collector
(DI1)*5 Internal circuit type Photocoupler diode input, current source
Open terminal voltage The maximum voltage between the ground and input terminals is the supply
voltage to the unit.
Terminal current (when shorted) 9 mA DC max.
Allowable contact resistance ON conditions: 500 Ω max., OFF conditions: 2000 kΩ min.
ON residual voltage 5.5 V DC max.
Built-in clock Accuracy Monthly error ±120 s (at 20 °C)
time*6
*1. PV is obtained from calculation based on the measured acceleration in x, y, and z directions, and is used for vibration detection
output, analog output, and waveform recording conditions. n Various calculations and judgment processes (P. 6-8)
*2. It is possible to output the SI value, synthesized AC acceleration, and JMA seismic intensity scale equivalent value from the
2-channel analog current output.
*3. If the vibration detection output exceeds the vibration detection conditions, the relay contact, which is the vibration detection
output, turns ON.
*4. If liquefaction is detected or if any serious failure or minor failure occurs, each DO output turns ON.
*5. This input can be used as a mode transition request input for maintenance mode or standby mode.
*6. The clock time is used for time stamps during waveform recording. The time can be adjusted using the loader. The clock IC is
backed up by the battery.
10-3
10 - 3 Other Specifications
Communication specifications
Item Description
Loader Connection The dedicated cable is connected to the loader jack.
specificationsCommunication system TTL level half-duplex 3-wire system
Baud rate 115200 bps
Communication Communication method 3-wire RS-485, half-duplex
Communication switchover When the loader cable is connected, RS-485 is capable of reading data
only.
Baud rate 38400 bps
Cable length 500 m max. (total length of all wiring)*
*As extension cabling for all wiring, use shielded twisted pair wires.
• For wiring for RS-485, do not connect an external terminating resistor. If
a terminating resistor is connected to either end of the transmission line,
communication is not possible.
• This device does not incorporate any countermeasures against lightning. If
there is a risk of power surge due to lightning, take protective measures.
 Lightning surge protection (P. 4-6)
External dimensions
Unit: mm
(44) 89 (69)
43 60
17
69
3×R
59.5
44.5
15 15
50
44.5
59.5
φ7 unit mounting holes (3)
Level adjustment M6 screw holes (3)

Flameproof packing
Cable gland
G3/4
122.5
109
75
External M4 ground terminal
10-4
APPENDIX
Glossary
Term Description Related sections Page
Accelerometer The acceleration detection element that is built into this unit. NAMES AND FUNCTIONS OF PARTS P. 2-1
The accelerometer can detect acceleration on the X-, Y-, and Z-axes. Performance Specifications P. 10-3
SI value A numeric value correlated with earthquake damage. The unit is SI calculation P. 6-10
kine (= cm/s). Vibration detection and liq- P. 6-22
The value that is actually read out or output is the maximum value uefaction judgment functions
that is obtained during a period of 10 to 20 seconds. Output functions P. 6-29
SI1: SI calculation in 8 directions, with 7 natural periods
SI2: SI calculation in 16 directions, with 24 natural periods
Synthesized AC Horizontal plane 2-axis or 3-axis vector synthesized AC acceleration. Synthesized AC acceleration P. 6-11
acceleration The unit is Gal (= cm/s2). calculation
The value that is actually read out or output is the maximum value Vibration detection and lique- P. 6-22
that is obtained during a period of 10 to 20 seconds. faction judgment functions
Output functions P. 6-29
JMA seismic A damage estimate value calculated from correlation equations Calculation of the JMA seis- P. 6-12
intensity scale using either the SI value only or the SI value and the synthesized AC mic intensity scale equiva-
equivalent value acceleration. lent value
Characterization Offsetting the temperature characteristics of the accelerometer us- Internal calculation pro- P. 6-7
compensation ing measurements from the temperature sensor, in order to improve cesses
the accuracy of the measured acceleration
Acceleration for An acceleration value that has the frequency band necessary to cal- Internal calculation processes P. 6-7
calculation culate the SI value and JMA seismic intensity scale equivalent value. Waveform recording P. 6-13
This acceleration is also used for the waveform recording and syn-
thesized AC acceleration PV.
Acceleration for An acceleration value whose high-frequency area is eliminated Internal calculation pro- P. 6-7
control when compared to the acceleration for calculation, in order to re- cesses
duce background noise for purposes of AO and monitoring.
Adjusted accel- Acceleration value after completion of bias adjustment Internal calculation processes P. 6-7
eration value Real-time data monitoring P. 7-1
Inclination accel- This value shows static acceleration due to temperature drift and Internal calculation processes P. 6-7
eration inclination of the place of installation. Real-time data monitoring P. 7-1
AC acceleration This is dynamic acceleration (= adjusted acceleration - inclination Internal calculation processes P. 6-7
acceleration) Real-time data monitoring P. 7-1
Vibration detec- If the SI value and synthesized acceleration value exceed the preset Vibration detection judg- P. 6-22
tion judgment values and the output conditions are satisfied, the unit enters the ment function
vibration detection state (i.e., vibration was detected).
Vibration detec- If the vibration detection judgment conditions are satisfied and no Vibration judgment function P. 6-22
tion output errors are detected, the vibration detection output relay turns ON. Output functions P. 6-29
Liquefaction If the liquefaction judgment conditions, such as SI value, synthe- Liquefaction judgment P. 6-22
judgment sized acceleration value, estimated displacement, and zero-cross function
count are satisfied, the unit enters the liquefaction detection state Output functions P. 6-29
(i.e., liquefaction was detected).
Liquefaction If the liquefaction judgment conditions are satisfied and no errors Liquefaction judgment P. 6-22
detection output are detected, the liquefaction output (DO4) turns ON. function
Output functions P. 6-29
Waveform record- Two kinds of waveform recording functions are provided: automatic Waveform recording P. 6-13
ing waveform recording (10 waveforms) and forced waveform recording
(1 waveform).
Error diagnosis Four types of error are detected: reset, serious failure, minor failure, Error diagnosis functions P. 6-26
and noise detection.
Reset If a serious failure that affects all functions occurs, the unit is reset. Error diagnosis functions P. 6-26
Minor failure This failure does not affect control output, but a check should be Error diagnosis functions P. 6-26
made for waveform record errors, errors in time records, and errone- LED output function P. 6-36
ous clock time. The installation conditions should also be checked.
The minor failure output turns ON.
App-1
APPENDIX
Term Description Related sections Page

Serious failure This failure may affect control output such as vibration detection Error diagnosis functions P. 6-26
output and liquefaction detection output. LED output function P. 6-36
The serious failure output turns ON and the control output turns OFF.
Noise detection & A signal other than the vibration waveform is detected. This failure Noise protection function P. 6-24
noise protection may affect the results of calculation. Error diagnosis functions P. 6-26
Various PVs are set to 0 or turned OFF. The minor failure output flashes. LED output function P. 6-36
Maintenance A fixed sequence of output changes in maintenance mode, allowing Maintenance sequence P. 6-34
sequence device operation and instrumentation to be checked on a connect-
ed external device.
Accelerometer A diagnostic circuit physically moves the accelerometer to check for Error diagnosis functions P. 6-26
diagnosis operational errors. Maintenance sequence P. 6-34
Auto bias Automatic adjustment of the bias, initiated using the loader. Acceleration calculation P. 6-7
process
Diagnosis and adjustment P. 7-8
function
FSG The 1960 Gal span that is the guaranteed accuracy acceleration Specifications P. 10-1
range (gravity acceleration reference ±980 Gal)
% FSG Percentage of the 1960 Gal span (±2 % FSG = ±39.2 Gal) Specifications P. 10-1
FSO The 4000 Gal span that is the measurable acceleration range (±2000 Gal) Specifications P. 10-1
% FSO Percentage of the 4000 Gal span Specifications P. 10-1
Method of determining acceleration accuracy

The method of measuring static acceleration, such as by FSG sensitivity and FSG
middle point using the gravity of the earth, is described below.
Note that the acceleration measurement axes described in Chapter 2, “NAMES AND
FUNCTIONS OF PARTS,” are the dynamic acceleration directions due to vibration,
which are opposite to those of the static acceleration axes.
zz X-axis FSG measurement
(1) Position this unit as shown in figure 1A.
Expected acceleration adjustment (Gal) AC acceleration detection axis directions
X-axis (αX–980) Y-axis Z-axis Z

Y
-980 0 980
X
Measure the "–980 Gal" output of the X-
axis (αX–980).
Gravity = 980 Gal
Figure 1A: X-axis FSG measurement (αX–980)
(2) Position this unit as shown in figure 1B.

X
X-axis (αX+980) Y-axis Z-axis
980 0 980
Y
Z
Measure the "+980 Gal" output of the X-
axis (αX+980). Gravity = 980 Gal
Figure 1B: X-axis FSG measurement (αX+980)
App-2
APPENDIX
(3) ‌Measure the X-axis FSG sensitivity.

αXFSG = αX+980 – αX–980
The following accuracy standards apply to the FSG sensitivity calculated from
the above expression:
FSG sensitivity ±2 % FSG (1960 Gal – 39.2 Gal ≤ αXFSG ≤ 1960Gal + 39.2 Gal)
(4) ‌Measure the X-axis FSG middle point.
αX+980 + αX–980
αXFSG − mid =
2
The following accuracy standards apply to the FSG middle point calculated
from the above expression:
FSG middle point ±3 % FSG (–58.8 Gal ≤ αXFSG-mid ≤58.8 Gal)
zz Y-axis FSG measurement
X-axis Y-axis (αY–980) Z-axis Z

X
0 -980 980
Measure the "–980 Gal" output of the Y- Y
axis (αY–980).
Gravity = 980 Gal
Figure 2A: Y-axis FSG measurement (αY–980)

Y
X-axis Y-axis (αY+980) Z-axis
0 980 980
Measure the "+980 Gal" output of the Y- X
Z
axis (αY+980).
Gravity = 980 Gal
Figure 2B: Y-axis FSG measurement (αY+980)
(3) ‌Measure the Y-axis FSG sensitivity.

αYFSG = αY+980 – αY–980
FSG sensitivity ±2 % FSG (1960 Gal – 39.2 Gal ≤ αYFSG ≤ 1960 Gal + 39.2 Gal)
(4) ‌Measure the Y-axis FSG middle point.
αY+980 + αY–980
αYFSG−mid =
2
FSG middle point ±3 % FSG (–58.8 Gal ≤ αYFSG−mid ≤ 58.8 Gal)
App-3
APPENDIX
zz Z-axis FSG measurement

X-axis Y-axis Z-axis (αZ0) X

Y
0 0 0
Z
Measure the “0 Gal” output of the Z-axis Gravity = 980 Gal
(αZ0)
Figure 3A: Z-axis FSG measurement (αZ0)

Z
X-axis Y-axis Z-axis (αZ+1960)
0 0 1960 Y
X
Measure the “1960 Gal” output of the Gravity = 980 Gal
Z-axis (αZ+1960).
Figure 3B: Z-axis FSG measurement (αZ+1960)
(3) ‌Measure the Z-axis FSG sensitivity.

αZFSG = αZ+1960 − αZ0
FSG sensitivity ±2 % FSG (1960 Gal – 39.2 Gal ≤ αZFSG ≤ 1960 Gal + 39.2 Gal)
(4) ‌Measure the Z-axis FSG middle point.
αZ+1960 + αZ0
αZFSG−mid =
2
FSG middle point ±3 % FSG (980 – 58.8 Gal ≤ αZFSG−mid ≤ 980 + 58.8 Gal)
zz Example of measurement equipment (Azbil Corporation’s inspection equipment)
Azbil Corporation uses static acceleration generation equipment with orthogonal-
ized turntables on two axes with a horizontal plane adjustment function for accu-
racy inspection.
The angles of turntables 1 and 2 are adjusted to “0°” and the foot lengths of the
equipment are adjusted to level turntable 2.
To generate acceleration, static acceleration is output based on the angle of rotation
of each turntable.
AC acceleration detection axis directions
X Y Turntable 1
Z 180°
Unit
0° 180°
Turntable 2
0°
Feet: adjustable height
App-4
APPENDIX
‌Relationships between JMA seismic intensity, acceleration, SI value, and measured

JMA seismic intensity
Previous JMA seismic intensity level New JMA seismic intensity level Application of
JMA seismic inten-
JMA seismic Acceleration (Gal) JMA seismic Measured JMA seismic SI value (kine) (SI) sity scale equiva-
intensity (A) intensity intensity (M) lent value
0 A < 0.8 0 M < 0.5 - ×
1 0.8 ≤ A < 2.5 1 0.5 ≤ M < 1.5 - ×
2 2.5 ≤ A < 8.0 2 1.5 ≤ M < 2.5 - 
3 8.0 ≤ A < 25.0 3 2.5 ≤ M < 3.5 1.1 ≤ SI < 3.8 
4 25.0 ≤ A < 80.0 4 3.5 ≤ M < 4.5 3.8 ≤ SI < 12.6 
5 80.0 ≤ A < 250.0 5- 4.5 ≤ M < 5.0 12.6 ≤ SI < 22.9 
5+ 5.0 ≤ M < 5.5 22.9 ≤ SI < 41.7 
6 250.0 ≤ A < 400.0 6- 5.5 ≤ M < 6.0 41.7 ≤ SI < 75.9 
6+ 6.0 ≤ M < 6.5 75.9 ≤ SI < 138.2 
7 400.0 ≤ A 7 6.5 ≤ M 138.2 ≤ SI 
The JMA seismic intensity scale equivalent value can be regarded as the mea- : Applicable
sured JMA seismic intensity. : ‌Error may be large depending on the
The JMA seismic intensity scale equivalent value is obtained using expression 2. waveform.
 Calculation of the JMA seismic intensity scale equivalent value (P. 6-12) ×: ‌Not applicable due to a large amount
of error.
• The relationship between the JMA seismic intensity and acceleration value
stated in the above table should be used only as a rough estimate.
In particular, since the effect of the high-frequency component of
acceleration on the actual damage is small, the error in the case of an
acceleration waveform with a large high-frequency component will be large.
App-5
Revision History of CP-SP-1376E
Date Rev. Revised pages Description

Apr. 2015 1
Mar. 2017 2 6-32 Table of “ n Output selection” changed.
10-2 Maintenance parts set for SES70 was added.
10-3, 10-4 Old page 10-2 to 10-3
End of the manual Terms and Conditions were changed (to version No. AA511A-014-09).
Dec. 2018 3 ii, 3-1 WARNING was changed.
End of the manual Terms and Conditions were changed (to version No. AA511A-014-10).
Terms and Conditions
We would like to express our appreciation for your purchase and use of Azbil Corporation’s products.
You are required to acknowledge and agree upon the following terms and conditions for your purchase of Azbil Corporation’s products (system
products, field instruments, control valves, and control products), unless otherwise stated in any separate document, including, without limitation,
estimation sheets, written agreements, catalogs, specifications and instruction manuals.
1. Warranty period and warranty scope
1.1 Warranty period
Azbil Corporation’s products shall be warranted for one (1) year from the date of your purchase of the said products or the delivery of the
said products to a place designated by you.
1.2 Warranty scope
In the event that Azbil Corporation’s product has any failure attributable to azbil during the aforementioned warranty period, Azbil
Corporation shall, without charge, deliver a replacement for the said product to the place where you purchased, or repair the said
product and deliver it to the aforementioned place. Notwithstanding the foregoing, any failure falling under one of the following shall
not be covered under this warranty:
(1) Failure caused by your improper use of azbil product (noncompliance with conditions, environment of use, precautions, etc. set
forth in catalogs, specifications, instruction manuals, etc.);
(2) Failure caused for other reasons than Azbil Corporation’s product;
(3) Failure caused by any modification or repair made by any person other than Azbil Corporation or Azbil Corporation’s
subcontractors;
(4) Failure caused by your use of Azbil Corporation’s product in a manner not conforming to the intended usage of that product;
(5) Failure that the state-of-the-art at the time of Azbil Corporation’s shipment did not allow Azbil Corporation to predict; or
(6) Failure that arose from any reason not attributable to Azbil Corporation, including, without limitation, acts of God, disasters, and
actions taken by a third party.
Please note that the term “warranty” as used herein refers to equipment-only-warranty, and Azbil Corporation shall not be liable for any
damages, including direct, indirect, special, incidental or consequential damages in connection with or arising out of Azbil Corporation’s
products.
2. Ascertainment of suitability
You are required to ascertain the suitability of Azbil Corporation’s product in case of your use of the same with your machinery,
equipment, etc. (hereinafter referred to as “Equipment”) on your own responsibility, taking the following matters into consideration:
(1) Regulations and standards or laws that your Equipment is to comply with.
(2) Examples of application described in any documents provided by Azbil Corporation are for your reference purpose only, and
you are required to check the functions and safety of your Equipment prior to your use.
(3) Measures to be taken to secure the required level of the reliability and safety of your Equipment in your use
Although azbil is constantly making efforts to improve the quality and reliability of Azbil Corporation’s products, there exists
a possibility that parts and machinery may break down. You are required to provide your Equipment with safety design such
as fool-proof design,*1 and fail-safe design*2 (anti-flame propagation design, etc.), whereby preventing any occurrence of
physical injuries, fires, significant damage, and so forth. Furthermore, fault avoidance,*3 fault tolerance,*4 or the like should be
incorporated so that the said Equipment can satisfy the level of reliability and safety required for your use.
*1. A design that is safe even if the user makes an error.
*2. A design that is safe even if the device fails.
*3. Avoidance of device failure by using highly reliable components, etc.
*4. The use of redundancy.
3. Precautions and restrictions on application
3.1 Restrictions on application
Please follow the table below for use in nuclear power or radiation-related equipment.
Nuclear power quality*5 required Nuclear power quality*5 not required

Within a radiation Cannot be used (except for limit switches for Cannot be used (except for limit switches for
controlled area*6 nuclear power*7) nuclear power*7)
Outside a radiation Cannot be used (except for limit switches for Can be used
controlled area*6 nuclear power*7)
*5. Nuclear power quality: compliance with JEAG 4121 required

*6. Radiation controlled area: an area governed by the requirements of article 3 of “Rules on the Prevention of Harm from
Ionizing Radiation,” article 2 2 4 of “Regulations on Installation and Operation of Nuclear Reactors for Practical Power
Generation,” article 4 of “Determining the Quantity, etc., of Radiation-Emitting Isotopes,”etc.
*7. Limit switch for nuclear power: a limit switch designed, manufactured and sold according to IEEE 382 and JEAG 4121.
Any Azbil Corporation’s products shall not be used for/with medical equipment.
The products are for industrial use. Do not allow general consumers to install or use any Azbil Corporation’s product. However, azbil
products can be incorporated into products used by general consumers. If you intend to use a product for that purpose, please contact
one of our sales representatives.
3.2 Precautions on application
you are required to conduct a consultation with our sales representative and understand detail specifications, cautions for operation,
and so forth by reference to catalogs, specifications, instruction manual, etc. in case that you intend to use azbil product for any purposes
specified in (1) through (6) below. Moreover, you are required to provide your Equipment with fool-proof design, fail-safe design, anti-
flame propagation design, fault avoidance, fault tolerance, and other kinds of protection/safety circuit design on your own responsibility
to ensure reliability and safety, whereby preventing problems caused by failure or nonconformity.
(1) For use under such conditions or in such environments as not stated in technical documents, including catalogs, specification,
and instruction manuals
(2) For use of specific purposes, such as:
* Nuclear energy/radiation related facilities
[When used outside a radiation controlled area and where nuclear power quality is not required]
[When the limit switch for nuclear power is used]
* Machinery or equipment for space/sea bottom
* Transportation equipment
[Railway, aircraft, vessels, vehicle equipment, etc.]
* Antidisaster/crime-prevention equipment
* Burning appliances
* Electrothermal equipment
* Amusement facilities
* Facilities/applications associated directly with billing
(3) Supply systems such as electricity/gas/water supply systems, large-scale communication systems, and traffic/air traffic control
systems requiring high reliability
(4) Facilities that are to comply with regulations of governmental/public agencies or specific industries
(5) Machinery or equipment that may affect human lives, human bodies or properties
(6) Other machinery or equipment equivalent to those set forth in items (1) to (5) above which require high reliability and safety
4. Precautions against long-term use
Use of Azbil Corporation’s products, including switches, which contain electronic components, over a prolonged period may degrade
insulation or increase contact-resistance and may result in heat generation or any other similar problem causing such product or switch
to develop safety hazards such as smoking, ignition, and electrification. Although acceleration of the above situation varies depending
on the conditions or environment of use of the products, you are required not to use any Azbil Corporation’s products for a period
exceeding ten (10) years unless otherwise stated in specifications or instruction manuals.
5. Recommendation for renewal
Mechanical components, such as relays and switches, used for Azbil Corporation’s products will reach the end of their life due to wear by
repetitious open/close operations.
In addition, electronic components such as electrolytic capacitors will reach the end of their life due to aged deterioration based on
the conditions or environment in which such electronic components are used. Although acceleration of the above situation varies
depending on the conditions or environment of use, the number of open/close operations of relays, etc. as prescribed in specifications
or instruction manuals, or depending on the design margin of your machine or equipment, you are required to renew any Azbil
Corporation’s products every 5 to 10 years unless otherwise specified in specifications or instruction manuals. System products, field
instruments (sensors such as pressure/flow/level sensors, regulating valves, etc.) will reach the end of their life due to aged deterioration
of parts. For those parts that will reach the end of their life due to aged deterioration, recommended replacement cycles are prescribed.
You are required to replace parts based on such recommended replacement cycles.
6. Other precautions
Prior to your use of Azbil Corporation’s products, you are required to understand and comply with specifications (e.g., conditions and
environment of use), precautions, warnings/cautions/notices as set forth in the technical documents prepared for individual Azbil
Corporation’s products, such as catalogs, specifications, and instruction manuals to ensure the quality, reliability, and safety of those
products.
7. Changes to specifications
Please note that the descriptions contained in any documents provided by azbil are subject to change without notice for improvement
or for any other reason. For inquires or information on specifications as you may need to check, please contact our branch offices or
sales offices, or your local sales agents.
8. Discontinuance of the supply of products/parts
Please note that the production of any Azbil Corporation’s product may be discontinued without notice. After manufacturing is
discontinued, we may not be able to provide replacement products even within the warranty period.
For repairable products, we will, in principle, undertake repairs for five (5) years after the discontinuance of those products. In
some cases, however, we cannot undertake such repairs for reasons, such as the absence of repair parts. For system products, field
instruments, we may not be able to undertake parts replacement for similar reasons.
9. Scope of services
Prices of Azbil Corporation’s products do not include any charges for services such as engineer dispatch service. Accordingly, a separate
fee will be charged in any of the following cases:
(1) Installation, adjustment, guidance, and attendance at a test run
(2) Maintenance, inspection, adjustment, and repair
(3) Technical guidance and technical education
(4) Special test or special inspection of a product under the conditions specified by you
Please note that we cannot provide any services as set forth above in a nuclear energy controlled area (radiation controlled area) or at a
place where the level of exposure to radiation is equivalent to that in a nuclear energy controlled area.
AAS-511A-014-10
Specifications are subject to change without notice. (10)
1-12-2 Kawana, Fujisawa

Kanagawa 251-8522 Japan
https://www.azbil.com
1st edition: Apr. 2015 (V)
3rd edition: Dec. 2018 (A)

Intelligent Earthquake System

Uploaded by

Copyright:

Available Formats

Intelligent Earthquake System

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Intelligent Earthquake System

Uploaded by

Copyright:

Available Formats

No.

Thank you for purchasing an Azbil

© 2015–2018 Azbil Corporation. All Rights Reserved.

C AUTION Cautions are indicated when mishandling this product might

Use caution when handling the product.

The indicated action is prohibited.

Always follow the indicated instructions.

Notes indicate information that might benefit the user.

 Label and seal

Rating nameplate Warning label Seal

In Taiwan, this device cannot be used in an explosive atmosphere.

Use shielded cables for wiring.

Do not disassemble or modify this device.

Intelligent Earthquake Sensor Model SES70 User's Manual

SLP-SE7 Smart Loader Package for SES70 Intelligent Earthquake Sensor

Chapter 2. NAMES AND FUNCTIONS OF PARTS

Chapter 5. PREPARATIONS FOR START-UP

Chapter 6. INTERNAL PROCESSING

Chapter 7. LOADER ACCESS DATA

Chapter 8. MAINTENANCE AND TROUBLESHOOTING

Chapter 10. SPECIFICATIONS

Chapter 1. OVERVIEW  1-1

Chapter 2. NAMES AND FUNCTIONS OF PARTS  2-1

Chapter 3. INSTALLATION  3-1

Chapter 4. WIRING  4-1

Chapter 5. PREPARATIONS FOR START-UP  5-1

Procedure for setting the clock 

Chapter 6. INTERNAL PROCESSING  6-1

6-1 Modes  6-1

Chapter 7. LOADER ACCESS DATA  7-1

Real-time data monitoring data 

Chapter 8. MAINTENANCE AND TROUBLESHOOTING  8-1

Checklist for periodic inspection 

Chapter 10. SPECIFICATIONS  10-1

10-1 Specifications  10-1

Vibration detection output DCX350 (Azbil Corporation’s

SES70 Shutoff valve

2. Earthquake monitoring system

SES70 Lamp, etc.

3. Earthquake monitoring with 2-out-of-3 shutdown system

SES70 SES70 SES70

To create a redundant system, take into account the following:

Status display LEDs

 Basic function block diagram

Accelerometer Z RS-485 (DA)

Structure of the accelerometer

M5 retaining screw M6 hexagon socket setscrew

zz What to check after installation

When there might be an explosive atmosphere, do not open the cover.

1) Attach the case securely.

2) Insert a tool into the grooves

zz Screw terminal block

zz Spring terminal block

Note: The default setting is enclosed in brackets, [ ].

 Connecting the battery

Battery connector (2 places)

 Lightning surge protection

SES70 : Voltage-limiting element

Vibration detection Receiver for vibration

Vibration detection Receiver for vibration

Label and seal

Chapter 1. OVERVIEW 1-1

Chapter 2. NAMES AND FUNCTIONS OF PARTS 2-1

Chapter 3. INSTALLATION 3-1

Chapter 4. WIRING 4-1

Chapter 5. PREPARATIONS FOR START-UP 5-1

Procedure for setting the clock

Chapter 6. INTERNAL PROCESSING 6-1

6-1 Modes 6-1

Chapter 7. LOADER ACCESS DATA 7-1

Real-time data monitoring data

Chapter 8. MAINTENANCE AND TROUBLESHOOTING 8-1

Checklist for periodic inspection

Chapter 10. SPECIFICATIONS 10-1

10-1 Specifications 10-1

Basic function block diagram

Connecting the battery

Lightning surge protection

Procedure for setting the clock

Functions of the modes

Various calculations and judgment processes

Synthesized AC acceleration calculation

Calculation of the JMA seismic intensity scale equivalent value

Noise protection process

Waveform recording header information

Automatic waveform recording

Example of maximum value recording without trigger update

Example of maximum value recording with trigger update