Operating Instructions

LVC-A910
LVC-A911
LVC-A912
LVC-A913

Before installing and using the camera,

please read these instructions thoroughly
and retain them for later reference.
 Warning
To prevent fire or shock hazard,do not expose the unit to rain or moisture.
CAUTION To avoid electrical shock,do not open the cabinet. Refer servicing to quali-
RISK OF ELECTRIC SHOCK fied personnel only.
DO NOT OPEN
Regulatory Notices For U.S.A
This equipment has been tested and found to comply with the limits for a
CAUTION:TO REDUCE THE RISK OF Class A digital device, pursuant to Part 15 of the FCC Rules.These limits
ELECTRIC SHOCK, DO NOT REMOVE are designed to provide reasonable protection against harmful interfer-
COVER(OR BACK) NO USER SERVICE- ence when the equipment is opearted in a commercial environment.
ABLE PARTS INSIDE. This equipment generates, uses, and can radiate radio frequency ener-
gy and, if not installed and used in accordance with the instruction manu-
REFER SERVICING TO QUALIFIED SER- al, may cause harmful interference to radio communications. Operation of
VICE PERSONNEL. this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his
own expense.
This symbol is intended to alert the • A suitable conduit entries, knock-outs or glands shall be provided in the
user to the presence of uninsulated cable entries of this product in the end user.
“dangerous voltage” within the prod- • Caution:Danger of explosion if battery is incorrectly replaced. Replaced
uct’s enclosure that may be of suffi- only with the same or equivalent type recommended by the manufactur-
er. Dispose of used batteries according to the manufacturer’s instruc-
cient magnitude to constitute a risk of tions.
electric shock to persons. • Holes in metal, through which insulated wires pass, shall have smooth
well rounded surfaces or shall be provided with brushings.
This symbol is intended to alert the
user to the presence of important Warning
operating and maintenance (servic- This is a class A product. In a domestic environment this product
ing) instructions in the literature may cause radio interference in which case the user may be
required to take adequate measures.
accompanying the appliance.

2
 Contents
Features............................................................................................................................................................................3
Cautions for Safe Operation ............................................................................................................................................4
Operating Controls and Their Functions.......................................................................................................................5
Power IN/CONTROL .....................................................................................................................................................6-7
External Key(A/D IN)........................................................................................................................................................8
MENU DESCRIPTIONS ....................................................................................................................................................9
CAMERA ID ................................................................................................................................................................10
FOCUS MODE SET ...............................................................................................................................................11-12
AWB SET ...............................................................................................................................................................13-14
AE SET ..................................................................................................................................................................15-17
SPECIAL SET ........................................................................................................................................................18-19
MOTION DET ..............................................................................................................................................................20
F. OSD SET ................................................................................................................................................................21
E. SENSITIVITY ..........................................................................................................................................................22
WDR SET ....................................................................................................................................................................23
On-Screen Display....................................................................................................................................................24-25
Specifications ...........................................................................................................................................................26-27

FEATURES
The power zoom color video camera is designed for use in monitoring system.
• High resolution and high sensitivity with a 1/4 inch CCD (Charge Coupled Device)
• High magnitude of zoom lens with optical X 22, Digital X 176
• Auto Focus
• Auto White balance
• Auto exposure with DC Iris control
• On Screen display
• Wide Dynamic Range (option) : LVC-A912, 913
• Digital low shutter (option) : LVC-A911, 913 3
 Cautions for Safe Operation
Power Supply • Close to generators of powerful electromagnetic
This camera must always be operated a 12V DC radiation such as radio or TV transmitters.
power supply.
Care of the unit
Handling of the unit • Remove dust or dirt on the surface of the lens
Be careful not to spill water or other liquids on the with a blower.
unit, or to get combustible or metallic material • Use a dry soft cloth to clean the body. If it is very
inside the body. If used with foreign matter inside, dirty, use a cloth dampened with a small quantity
the camera is liable to fail, or to be a cause of fire of neutral detergent, then wipe dry.
or electric shock. • Avoid the use of volatile solvents such as
thinners, alcohol, benzene, and insecticides.
Operating and storage location They may damage the surface finish and/or
Avoid viewing a very bright object (such as light fit- impair the operation of the camera.
tings) for an extended period. Avoid operating or
storing the unit in the following locations.

• Extremely hot or cold places (operating tempera-

ture 0°C-45°C)
• Damp or dust place
• Where it is exposed to rain
• Where it is subject to strong vibration

4
Operating Controls and Their Functions
1. Tripod adaptor
This adaptor can also be attached on the bottom of the camera.
2. Lens mount cap
3. TELE Key
When push the TELE KEY, picture is telephoto
4. WIDE Key
When push the WIDE KEY, picture is wide angle
5. Focus Near Key
In a manual situation, focus get near.
6. Focus Far Key
In a manual situation, focus get far.
7. Menu Key
If you want to set up a diverse function, you can push this button.
8. Video output (S-Video type)
Connect to the S-Video in connector of a monitor.
9. Interface of camera control JACK (12 Pin Din Jack Type)
• Connect to an external voltage controller
• You can supply a camera with power from this. (DC12V)
10. Video output(BNC type)
Connect to the video in connector of a monitor.

5
Power In / Control

You can adjust focus and zoom by a pin terminal on the back side
of the camera.

* is the color of the cable.(If it is offered)

6
Power In / Control

7
 External Key (A/D IN)
Schematic diagram of wired
remote-control

8
MENU DESCRIPTIONS

page 10
page 11-12
page 13-14
page 15-17
page 18-19
page 20
page 21
page 22
page 23

Using TELE, WIDE, FOCUS+, FOCUS- button

• TELE and WIDE are used for UP and DOWN.
• FOCUS+ and FOCUS- are used for INCREASE and DECREASE the data.

9
 CAMERA ID
1. CAMERA ID
To connect a large number of camera , It can be
assigned to identification number to each camera for
camera control easily.
(OFF, 0 - 255 : total numbers of ID are 256)
• It only can be set this function using ID commend.
To transfer ID Code of camera , In first byte at PC control.
Set the ID number of camera , and then the ID number
display continuously.

10
FOCUS MODE SET
2. Focus Set:
2-1. Focus Mode Set :
This function is for focus mode setting
A) Set up "FOCUS SET" in main menu using Menu key.
Select the "FOCUS MODE" in submenu using Tele/Wide
key. And then set the mode (Auto, Push auto, or Manual)
using Focus key.
2-2. Focus Distance Set :
This function is for selection of minimum shooting
distance.
A) Select the "FOCUS DIST" in submenu using Tele/wide key.
B) Set the focus distance mode from 1cm to 5M. (1cm, 10cm,
50cm, 1M, 3M, 5M) using Focus key.
2-3. ZOOM START Set :
This function is for selection of zoom start position.
A) Select the "ZOOM START" in submenu using Tele/wide key.
B) Set the Zoom start mode from x1 to x21. using Focus key.

11
 FOCUS MODE SET
2-4. ZOOM END Set :
This function is for selection of zoom end position.
A) Select the "ZOOM END" in submenu using Tele/wide key.
B) Set the Zoom end mode from X(Zoom Start + 1) to x176 using
Focus key.
2-5. ZOOM SPEED Set :
This function is for selection of zoom speed.
A) Select the "ZOOM SPEED" in submenu using Tele/wide key.
B) Set the Zoom speed, Slow, Middle , Quick using Focus key.
2-6. ZOOM TRACKING MODE Set :
This function is for selection of zoom tracking mode.
A) Select the "ZTRK" in submenu using Tele/wide Command,
B) Set the Zoom tracking mode to Auto or Manual.
* Zoom tracking means focused zooming state.
2-7. INITIAL SET :
If initial mode set to ON, All FOCUS SET function is
changed to the factory setting.
A) Select the "INITIAL SET" in submenu using Tele/wide key.
B) Set the initial set mode to ON or OFF using Focus key.
2-8. RETURN TO MAIN MENU :
This function is exit to main menu.
A) Select the "RETURN" in submenu using Tele/wide key.
B) Set the return mode using Focus key.
12
AWB SET
3. AWB SET
3-1. WB Mode Set :
This function is for changing the WB mode.
A) Set up "AWB SET" in main menu using Tele/wide key.
B) Select the "WB MODE" in submenu using Tele/wide key.
C) Set the mode Auto, Push auto , Manual, Outdoor, Indoor,
Special using Focus key.
*WBC MODE ; Use for changing White Balance Mode .
1) AUTO ; WB Range 2800 °K ~ 8000 °K .
2) PUSH AUTO ; Set the AWB mode to Push Auto, then WB
Mode is auto.
3) SPECIAL ; Under the special WB condition( Differ from curve of the
control color temperature ) , Adjust Red and Blue to perform a
desired Auto White Balance.
3-2. RED ADJUST Set :
This function is available for Special ,Push Auto,
Manual WB mode.
This mode is the adjustment of user option for special color.
A) Select the "RED ADJUST" in submenu using Tele/wide key.
B) Adjust the level from (-30 to 30 SPECIAL,
-128 to +127 PUSH AUTO, 0-255 MANUAL) using Focus key.

13
 AWB SET
3-3. BLUE ADJUST Set :
This function is available for Special, Push Auto,
Manual WB mode.
This mode is the adjustment of user option for special
color.
A) Select the "BLUE ADJUST" in submenu using Tele/wide key.
B) Adjust the level from (-30 to 30 SPECIAL,
-128 to +127 PUSH AUTO, 0-255 MANUAL) using Focus key.
3-4. PUSH AUTO :
In case of PUSH AUTO WB mode.
Adjust the push auto mode ON, WB act automatically.
3-5. INITIAL SET :
If initial mode set to ON, All AWB function is changed
to the factory setting
A) Select the "INITIAL SET" in submenu using Tele/wide key.
B) Set the initial set mode to ON or OFF using Focus key.
3-6. RETURN TO MAIN MENU :
This function is exit to main menu.
A) Select the "RETURN " in submenu. Using Tele/wide key.
B) Set the return mode using Focus key.

14
AE SET
4. AE SET
4-1. AE Mode Set :
This function is for changing to AE mode.
A) Set up "AE SET" in main menu using Tele/wide key.
B) Select the "AE MODE" in submenu using Tele/wide key.
C) Set the mode auto, IRIS MAN, AGC MAN, Manual, Auto using
Focus key.
4-2. IRIS ADJUST Set :
This function is available for IRIS MAN mode.
A) Select the "IRIS ADJUST" in submenu using Tele/wide key.
B) Adjust the level from ##MIN to ##MAX(MANUAL, IRIS MAN) using
Focus key.
* ## : Current level at Auto mode.
4-3. AGC ADJUST Set :
This function is available for AGC MAN mode.
A) Select the "AGC ADJUST" in submenu using Tele/wide key.
B) Adjust the level from ##MIN to ##MAX(MANUAL, AGC MAN) using
Focus key.
* ## : Current level at Auto mode.

15
 AE SET
4-4. BRIGHTNESS ADJUSTMENT Set :
A) Select the "BRIGHTNESS" in submenu using Tele/wide key.
B) Adjust the level from ##MIN to ##MAX. using Focus key.
* ## : Current level at Auto mode.
4-5. BACKLIGHT Set :
A) Select the "BACKLIGHT" in submenu using Tele/wide key.
B) Set the mode OFF, ON, or AUTO using Focus key.
* Auto BLC (Auto back light compensation)
When a back light condition occurs in area1,area2, area3, or area4.
the back light compensation is enable. When the back light
condition disappears in that area,
BLC is disable automatically. If do not want this mode, set to OFF
4-6. FLICKERLESS Set :
Area1
A) Select the "FLICKERLESS" in submenu using Tele/wide key.
Area2 Area0 Area3 B) Set the mode OFF, ON using Focus key.
* FLICKERLESS ; Use for removing the flicker of picture
Area4
ON : Remove the flicker ( In case of NTSC System ; Shutter Speed
1/100 sec
Auto BLC In case of PAL System ; Shutter Speed 1/120 sec ).

16
AE SET
4-7. SHUTTER SPEED Set :
A) Select the "SHUTTER" in submenu using Tele/wide key.
B) Set the mode NORMAL, 1/125 - 1/10000 using Focus key.
4-8. INITIAL SET :
A) Select the "INITIAL SET" in submenu using Tele/wide
Command,
B) Set the initial set mode to ON or OFF using Focus key.
4-9. RETURN TO MAIN MENU :
This function is exit to main menu.
A) Select the "RETURN " in submenu using Tele/wide key.
B) Set the return mode using Focus key.

17
 SPECIAL SET
5. SPECIAL SET
5-1. User Title Set :
This function is for custom title on screen display.
A) Set "SPECIAL SET" in main menu using Tele/wide key.
B) Select the"USER TITLE" in submenu using Tele/wide key.
C) Set the position of title and set data using Tele / Wide,
Focus key.
5-2. SHARPNESS ADJUST Set :
A) Select the "SHARPNESS" in submenu using Tele/wide key.
B) Adjust the level from 0 to 15 using Focus key.
5-3. MIRROR Set :
A) Select the "MIRROR" in submenu using Tele/wide key.
B) Select the mode ON, OFF using Focus key.
5-4. COLOR Set :
This mode is for B/W mode.
A) Select the "COLOR" in submenu using Tele/wide key.
B) Select the mode ON, OFF using Focus key.

18
SPECIAL SET
5-5. NEGATIVE Set :
This mode is to change color and luminance to negative.
A) Select the "COLOR" in submenu using Tele/wide key.
B) Select the mode ON, OFF using Focus key.
5-6. WIDE BURST Set :
This mode is to change color burst width for long dis-
tance application.
A) Select the"WIDE BURST" in submenu using Tele/wide key.
B) Select the mode ON, OFF using Focus key.
5-7. INITIAL SET :
If initial mode set to ON, All SPECIAL functions are
changed to the factory setting
A) Select the "INITIAL SET" in submenu using Tele/wide key.
B) Set the initial set mode to ON or OFF Using Focus key.
5-8. RETURN TO MAIN MENU :
This function is exit to main menu.
A) Select the "RETURN" in submenu using Tele/wide key.
B) Set the return mode Using Focus key.

19
 MOTION DET
6. MOTION DETECTION SET
6-1. DETECTION Mode Set :
A) Set "MOTION" in main menu using Tele/wide key.
B) Select the "DETECTION" in submenu. Using Tele/wide key.
C) Set the mode ON, OFF using Focus key.
6-2. LEVEL ADJUST Set :
This function is available for DETECTION ON mode.
A) Select the "LEVEL SET" in submenu. Using Tele/wide key.
B) Adjust the level to some sensitivity using Focus key.
6-3. INITIAL SET :
If initial mode set to ON, All MOTION functions are
changed to the factory setting
A) Select the "INITIAL SET" in submenu using Tele/wide key.
B) Set the initial set mode to ON or OFF Using Focus key.
6-4. RETURN TO MAIN MENU :
This function is exit to main menu.
A) Select the "RETURN" in submenu using Tele/wide key.
B) Set the return mode Using Focus key.

20
F. OSD SET
7. F. OSD SET
7-1. FUNCTION Set :
A) Set "F. OSD" in main menu using Tele/wide key.
B) Select the mode what you want in submenu using Tele/wide key.
C) Set the display mode of OSD using Tele / Wide, Near/Far key.
*INITIAL SET and RETURN are the same as before procedure.

21
 E. SENSITIVITY SET
8. E. SENSITIVITY SET: (option)
8-1. E. SENSITIVITY SET
A) Select the "E.SENSITIVITY" in submenu using Tele/wide key.
B) Select the sensitivity mode what you want in submenu using
Focus key.
* Mode sequence : OFF-X2 AUTO-X4 AUTO-X8 AUTO-
X10AUTO-X16 AUTO- X32 AUTO
-OFF- X2 FIX-X4 FIX -X8 FIX -X10 FIX -X16 FIX - X32 FIX-OFF
8-2. INITIAL SET :
If initial mode set to ON, E.SENSITITY functions are
changed to the factory setting
A) Select the "INITIAL SET" in submenu using Tele/wide key.
B) Set the initial set mode to ON or OFF Using Focus key.
8-3. RETURN TO MAIN MENU :
This function is exit to main menu.
A) Select the "RETURN" in submenu using Tele/wide key.
B) Set the return mode Using Focus key.

22
WDR SET
9. WDR SET (option)
9-1. WDR SET
A) Select the "WDR" in main menu using Tele/wide key.
B) Select the "WDR CONTROL" in submenu using Tele/wide key.
C) Select the WDR mode what you want in submenu using Focus key.
* Mode sequence : OFF -- ON -- AUTO
* WDR Auto mode is working at the condition of high light
back light.
9-2. LEVEL ADJUST Set :
This function is the gain adjustment of WDR
A) Select the "SENSITIVITY" in submenu using Tele/wide key.
B) Adjust the level to some sensitivity using Focus key.
9-3. INITIAL SET :
If initial mode set to ON, All WDR functions are
changed to the factory setting
A) Select the "INITIAL SET" in submenu using Tele/wide key.
B) Set the initial set mode to ON or OFF Using Focus key.
9-4. RETURN TO MAIN MENU :
This function is exit to main menu.
A) Select the "RETURN" in submenu using Tele/wide key.
B) Set the return mode Using Focus key.
23
 On Screen Display
FUNCTION OSD Format Description
Some of these functions will
be displayed every time the 1. Focus Mode Non display Auto Mode
camera is operated and then Manual / push Auto Mode
disappeared after 5 seconds. 2. Back Light Non display Back Light OFF
"BL"display BLC ON / Auto BLC Mode
3. Shutter Speed Non display Normal Shutter (NTSC:1/60
1 2 3 6 PAL: 1/50)
"Ff"display Flickerless Mode
1/125

1/10,000
4. CAMERA ID According to write the identification number to
each camera, Multi-point control is available
(PC Control 000~255).
5. ZOOM Display DX 176 Digital Zoom mode
X 22 Optical Zoom mode
5 7 4

24
 On Screen Display
FUNCTION OSD Format Description
6. STAND-BY Indicate the camera stand-by during the
camera’s power turning ON.
7. WBC Mode White Balance AUTO
Special Auto White Balance; Adjustment Mode according to
S change of external illuminant. RED ADJUST and BLUE
W
ADJUST (0~255) are available. After changing R/B value, The
mainternance mode is “AUTO”.
WBC Preset for INDOOR (3200°K)
WBC Preset for OUTDOOR (5100°K)
M Manual WBC Adjustment; In manual mode the HUE control is
W
available (0 ~ 99).
Push Auto White Balance; Turn this mode ON, the white trace
P
W automatically. Turn this mode OFF, preserve the white of final
auto tracing action (Manual).

25
 Specifications
Image device 1/4" interline transfer CCD
NTSC, High resolution : 811(H) X 508(V) 410K
NTSC, Normal resolution :537(H) X 505(V) 270K
PAL, High resolution : 795 (H) X 596 (V) 470K
PAL, Normal resolution : 537(H) X 597(V) 320K
Sync system Internal sync
Horizontal resolution Approx.480 Line (NTSC, High resolution)
320 Line (NTSC, Normal resolution)
480 Line (PAL, High resolution)
320 Line (PAL, Normal resolution)
(at center of screen)
Lens X 22 Zoom ( F 1.6 f = 3.9 ~ 85.8 mm ), Video AF
Digital Zoom Ratio X 8 ( Total Zoom Ratio X 176 )
Minimum illumination LVC-A910/912 SERIES : 1 Lux, AGC On
LVC-A911/913 SERIES : 0.01 Lux, X 32 Field Accumulate
S/N More than 48dB
Scanning System 2:1 Interlace
Scanning Frequency(H) 15.734kHz(NTSC), 15.625kHz(PAL)
Scanning Frequency(V) 59.94Hz(NTSC), 50Hz(PAL)

26
 Specifications
Focal Length 0.01m (WIDE), 1.0m (TELE)
OSD(On Screen Display) ON/ OFF
Power requirement DC 12V
Video output Composite Output 75Ω Terminated / Y,C Separated
Power consumption 5W
operating temperature 0°C - 45°C
Operating Humidity 0% RH - 60% RH
Storage temperature -20°C - 60°C, 0% RH - 85% RH
Dimensions 56.2mm(W) x 64mm(H) x 101mm(D)
Weight 388g

Specifications are subject to change without notice.

P/NO: 3834RS0075C
27
‫ݷ‬ᔫᒎฉ
LVC-A910
LVC-A911
LVC-A912
LVC-A913

在您使用此摄像机之前，请完整阅读此操
作指南以供参考。
 வস
ᓖፀ 为了防止电击事故，请不要将该产品暴露在雨中或潮湿的环境中。
为了避免电击的危险，请不要打开机壳，如需维修，请联系专业维
电击危险请勿打开 修人员。

ਖࢾဉී U.S.A
警告：为了减少电击的危险，请勿拆下前 本产品经测试符合 FCC 第 15 部分有关 A 类数字设备的限制条件
这些限制条件是为提供合理的保护措施 防止在商业环境中安装设
盖（或后盖） 备时产生有害干扰而制定的 本产品会产生 使用和辐射无线电频
率能量 如未正确安装和使用 可能对无线电通讯造成有害干扰
内部没有任何用户可以维修的零部件。 在住宅环境中使用此产品会产生有害干扰 在此情况下用户需要自
如需维修，请联系专业维修人员。 行采取措施消除此干扰
• 终端用户使用的此产品的电缆入口中提供了合适的导管引入装置
剔除装置或密封套
• 注意 如果电池更换不当 则会有爆炸的危险 请使用同一型号
此符号用于警示用户，产品外壳存在 或制造商建议的电池型号
未绝缘的危险电压，会产生对人身造 请按照制造商的说明处置废旧电池
• 绝缘线穿过的金属孔应当具有光滑 圆形的表面 或者应当是刷
成电击的危险。
光的

வস
此符号用于提醒用户，随设备一起提 ‫ޘ۾‬ອᆐ A ಢ‫ޘ‬ອăᏴᓕᐤણஹሆဧ፿‫ޘ۾‬ອဟLj჈భถ્‫ޘ‬ည
供的印刷品中包含重要的操作和维护 ࢟ࠟছཷLjᏴࠥ༽ౚሆ፿ઓኊገ‫ݧ‬ནሤ።ࡼࡅဗă
（维修）指南。

2
 ෹ഺ
ᄂቶ....................................................................................................................................................................................3
‫ڔ‬ཝ‫ݷ‬ᔫᓖፀူሲ .............................................................................................................................................................4
‫ݷ‬ᔫ఼ᒜૺ໚৖ถ ..............................................................................................................................................................5
࢟Ꮞၒྜྷ0఼ᒜ ................................................................................................................................................................6-7
ᅪ‫ݝ‬୆ (A/D IN)..................................................................................................................................................................8
‫࡝ݩ‬ႁී ............................................................................................................................................................................9
摄像机 ID .....................................................................................................................................................................10
对焦模式设置..........................................................................................................................................................11-12
自动白平衡设置 ......................................................................................................................................................13-14
自动均衡设置..........................................................................................................................................................15-17
特殊设置.................................................................................................................................................................18-19
运动检测 ......................................................................................................................................................................20
F. OSD设置 .................................................................................................................................................................21
E. 敏感度 .....................................................................................................................................................................22
宽动态范围设置 ...........................................................................................................................................................23
ື෵‫࡝ݩ‬መာ (OSD)...................................................................................................................................................24-25
ਖৃ ............................................................................................................................................................................26-27

ᄂ࢛
此电动变焦彩色摄像机是为监视系统专门设计的。
• 高分辨率 高灵敏度的 1/4 英寸 CCD 电荷耦合装置
• 高倍数变焦镜头 光学变焦 X 22 数码变焦 X 176
• 自动对焦
• 自动白平衡
• DC 光圈控制自动曝光
• 屏幕菜单显示
• 宽动态范围 可选 LVC-A912, 913
• 数字低快门 可选 LVC-A911, 913 3
 ‫ڔ‬ཝ‫ݷ‬ᔫᓖፀူሲ
࢟Ꮞ ࿳ስ૦ۣዸ
此摄像机必须始终使用 12V DC 电源 • 使用吹风机将表面的灰尘或脏物吹掉
• 请使用软布清洁机身 如果太脏 请使用带有少
‫ۃ‬Ꮵ࿳ስ૦ 量中性清洁剂的软布清洁 然后擦干
请注意不要将水或其它液体溅到摄像机内部 也不 • 请不要使用挥发性溶剂 如稀释剂 酒精 苯和
要让可燃性物品或金属物品掉入摄像机内 如果摄 杀虫剂 会损坏表面或机身
像机内部有杂质 则可能会导致摄像机故障或引发
火灾或电击

ဧ፿ਜ਼ࡀह࢐࢛
不要长时间观看过于明亮的物体 如灯具 避免在
以下环境中使用或存放此设备

• 过热或过冷的地方 工作温度 0°C-45°C)

• 潮湿或有灰尘的地方
• 有雨的地方
• 有强烈振动的地方
• 靠近有强电磁辐射的地方 如收音机或电视发射
机附近

4
‫ݷ‬ᔫ఼ᒜૺ໚৖ถ
1. ྯ୭ଦᓞ୻໭
此转接器还可以安装到摄像机的底部
2. ஻ᄿ‫ڔ‬ᓤঙ
3. TELE୆
当按 TELE KEY 时 图像为远距拍摄
4. WIDE୆
当按 WIDE KEY 时 图像为广角拍摄
5. ౯தୡ௦୆
在手动操作时 将焦距拉近
6. ౯Ꮠୡ௦
在手动操作时 将焦距拉远
7. ‫࡝ݩ‬୆
如果您要设置不同的功能 可按此键
8. ၁ຫၒ߲ S-Video ቯ
连接到监视器的 S-Video 输入接口
9. ࿳ስ૦఼ᒜ JACK ୻ా 12 ᑣ DIN JACK ቯ
• 连接到外部电压控制器
• 您可以通过此接口为摄像机供电 (DC12V)
10. ၁ຫၒ߲ BNC ቯ
连接到监视器的视频输入接口

5
࢟Ꮞၒྜྷ0఼ᒜ

您可以通过摄像机背面的针形端子调节焦距和变焦。

* 为电缆颜色。（如果提供）

6
࢟Ꮞၒྜྷ0఼ᒜ

7
ᅪ‫ݝ‬୆ (A/D IN)
线控示意图

镜像

8
‫࡝ݩ‬ႁී

ဧ፿ TELE WIDE FOCUS+ FOCUS- ୆

• TELE 远摄 和 WIDE 广角 用于 UP 拉近 和 DOWN 拉远
• FOCUS+ 拉长焦距 和 FOCUS- 拉近减少 用于 INCREASE 增加 和
DECREASE 减少 数据
9
 ࿳ስ૦ ID
1. ࿳ስ૦ ID
当连接多台摄像机时 可以为每台摄像机指定一个识别
码 这样就可以更容易的对每台摄像机进行控制
(OFF, 0 - 255 ID 总数为 256)
• 只能使用推荐的 ID 来设置此功能
要发送摄像机的 ID 代码 使用 PC 控制的第一个字节
设置摄像机的 ID 编号 然后 ID 编号将连续显示

10
࣪ୡෝါ࿸ᒙ
2. ࣪ୡ࿸ᒙǖ
2-1. ࣪ୡෝါ࿸ᒙǖ
ࠥ৖ถ፿᎖࿸ᒙ࣪ୡෝါ
A) 使用菜单键在主菜单中设置 FOCUS SET 使用
Tele/Wide 键选择子菜单中的 FOCUS MODE 然后使用
对焦键设置模式 Auto(自动) Push auto(强制自动)
Manual(手动))
2-2. ࣪ୡ௦ಭ࿸ᒙ
ࠥ৖ถ፿᎖ኡᐋᔢቃ๜࿳௦ಭ
A) 使用 Tele/Wide 键选择子菜单中的 FOCUS DIST
B) 使用对焦键在 1cm 到 5M 之间设置对焦距离模式 (1cm,
10cm, 50cm, 1M, 3M, 5M)
2-3. ‫ܤ‬ୡఎဪ࿸ᒙ
ࠥ৖ถ፿᎖ኡᐋ‫ܤ‬ୡఎဪᆡᒙ
A) 使用 Tele/Wide 键选择子菜单中的 ZOOM START
B) 使用对焦键在 x1 到 x21 之间设置变焦开始模式

11
 ࣪ୡෝါ࿸ᒙ
2-4. ‫ܤ‬ୡஉၦ࿸ᒙ
ࠥ৖ถ፿᎖ኡᐋ‫ܤ‬ୡஉၦᆡᒙă
A) 使用 Tele/Wide 键选择子菜单中的 ZOOM END
B) 使用对焦键在 变焦开始 + 1 x176 到 X 之间设置变焦结束模式
2-5. ‫ܤ‬ୡႥࣞ࿸ᒙ
ࠥ৖ถ፿᎖ኡᐋ‫ܤ‬ୡႥࣞă
A) 使用 Tele/Wide 键选择子菜单中的 ZOOM SPEED
B) 使用对焦键设置变焦速度 Slow 低 Middle 中 Quick 快
2-6. ‫ܤ‬ୡৌᔍෝါ࿸ᒙ
ࠥ৖ถ፿᎖ኡᐋ‫ܤ‬ୡৌᔍෝါ
A) 使用 Tele/Wide 命令选择子菜单中的 ZTRK
B) 将变焦跟踪模式设置为 Auto 自动 或 Manual 手动
* ‫ܤ‬ୡৌᔍᒎ௡ୡ‫ܤ‬ୡᓨზă
2-7. ߱ဪ࿸ᒙ
ྙਫ߱ဪෝါ࿸ᆐ ON ఎ Ⴥᎌ FOCUS SET ࣪ୡ࿸ᒙ ৖
ถ୓‫ۻ‬খ‫ޣ߲ࡵܤ‬࿸ᒙ
A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET
B) 使用对焦键将初始模式设为 ON 或 OFF
2-8. ऩૄᓍ‫࡝ݩ‬
ࠥ৖ถ፿᎖ᅓ߲ᓍ‫࡝ݩ‬
A) 使用 Tele/Wide 键选择子菜单中的 RETURN
B) 使用对焦键设置返回模式
12
ᔈࣅ‫ڹ‬ຳੰ࿸ᒙ
3. ᔈࣅ‫ڹ‬ຳੰ࿸ᒙ
3-1. ‫ڹ‬ຳੰෝါ࿸ᒙ
ࠥ৖ถ፿᎖ኀখ‫ڹ‬ຳੰෝါ
A) 使用 Tele/Wide 键在主菜单中设置 AWB SET
B) 使用 Tele/Wide 键选择子菜单中的 WB MODE
C) 使用对焦键设置模式 Auto(自动) Push auto(强制自动)
Manual(手动) Outdoor(室外) Indoor(室内) Special(特殊)
*WBC MODE: ፿᎖ኀখ‫ڹ‬ຳੰෝါ
1) AUTO 白平衡范围 2800 °K ~ 8000 °K
2) PUSH AUTO 将 AWB 模式设为 Push Auto 强制自动 则白
平衡模式会自动调整
3) SPECIAL 在特殊的白平衡条件 不同于控制色温曲线 下 调
整红色和蓝色以达到所需的自动白平衡
3-2. ੺ྻࢯᑳ࿸ᒙ
ࠥ৖ถభ፿᎖ Special Push Auto Manual WB ෝါ
ࠥෝါဵ࣪ᄂၐዕྻ፿ઓኡሲࡼࢯᑳ
A) 使用 Tele/Wide 键选择子菜单中的 RED ADJUST
B) 使用对焦键调节值大小 -30 到 30 SPECIAL -128 到 +127
PUSH AUTO 0-255 MANUAL

13
 ᔈࣅ‫ڹ‬ຳੰ࿸ᒙ
3-3. ౸ྻࢯᑳ࿸ᒙ
ࠥ৖ถభ፿᎖ Special Push Auto Manual WB ෝါ
ࠥෝါဵ࣪ᄂၐዕྻ፿ઓኡሲࡼࢯᑳ
A) 使用 Tele/Wide 键选择子菜单中的 BLUE ADJUST
B) 使用对焦键调节值大小 -30 到 30 SPECIAL -128 到 +127
PUSH AUTO 0-255 MANUAL
3-4. PUSH AUTO ༓ᒜᔈࣅ
Ᏼ PUSH AUTO WB ෝါሆ
୓༓ᒜᔈࣅෝါ࿸ᆐ ON WB ્ᔈࣅᒊቲ
3-5. ߱ဪ࿸ᒙ
ྙਫ߱ဪෝါ࿸ᆐ ON ఎ Ⴥᎌ AWB ᔈࣅ‫ڹ‬ຳੰ
৖ถ୓‫ۻ‬খ‫ޣ߲ࡵܤ‬࿸ᒙ
A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET
B) 使用对焦键将初始模式设为 ON 或 OFF
3-6. ऩૄᓍ‫࡝ݩ‬
ࠥ৖ถ፿᎖ᅓ߲ᓍ‫࡝ݩ‬
A) 使用 Tele/Wide 键选择子菜单中的 RETURN
B) 使用对焦键设置返回模式

14
ᔈࣅ௿ੰ࿸ᒙ
4. ᔈࣅ௿ੰ࿸ᒙ
4-1. ᔈࣅ௿ੰෝါ࿸ᒙ
ࠥ৖ถ፿᎖ኀখᔈࣅ௿ੰෝါă
A) 使用 Tele/Wide 键在主菜单中设置 AE SET
B) 使用 Tele/Wide 键选择子菜单中的 AE MODE
C) 使用对焦键设置模式为 ATUO IRIS MAN AGC MAN
Manual
4-2. ਒མࢯᑳ࿸ᒙ
ࠥ৖ถ፿᎖ IRIS MAN ෝါ
A) 使用 Tele/Wide 键选择子菜单中的 IRIS ADJUST
B) 使用对焦键在 ##MIN 到 ##MAX(MANUAL, IRIS MAN) 中调整设
置
* ## : 自动模式当前值。
4-3. ᔈࣅᐐፄ఼ᒜࢯᑳ࿸ᒙ
ࠥ৖ถ፿᎖ AGC MAN ෝါ
A) 使用 Tele/Wide 键选择子菜单中的 IRIS ADJUST
B) 使用对焦键在 ##MIN 到 ##MAX(MANUAL, AGC MAN) 中调整设
置
* ## : 自动模式当前值

15
 ᔈࣅ௿ੰ࿸ᒙ
4-4. ೡࣞࢯᑳ࿸ᒙ
A) 使用 Tele/Wide 键选择子菜单中的 BRIGHTNESS
B) 使用对焦键在 ##MIN 到 ##MAX 中调整设置
* ## : 自动模式当前值
4-5. ۳਒࿸ᒙ
A) 使用 Tele/Wide 键选择子菜单中的 BACKLIGHT
B) 使用对焦键设置模式为 OFF ON 或 ATUO
* ᔈࣅ BLC ᔈࣅ۳਒‫ޡݗ‬
W当区域 1 区域 2 区域 3 或区域 4 中的背光满足条件时
可使用背光补偿 当此区域中的背光条件消失时 BLC 自动
停用 如果不需要此模式 将其设为 OFF
4-6. ᇄ࿑ႄ࿸ᒙ
A) 使用 Tele/Wide 键选择子菜单中的 FLICKERLESS
B) 使用对焦键设置模式为 OFF ON
* FLICKERLESS ; ፿᎖ሿ߹ᅄስ࿑ႄ
ON 消除闪烁 对于 NTSC 系统 快门速度为 1/100 sec
(对于 PAL 制式快门速度未 1/120 sec ).

ᔈࣅ۳਒‫ޡݗ‬

16
ᔈࣅ௿ੰ࿸ᒙ
4-7. ౐ඡႥࣞ࿸ᒙ
A) 使用 Tele/Wide 键选择子菜单中的 SHUTTER
B) 使用对焦键设置模式为 NORMAL 1/125 - 1/10000
4-8. ߱ဪ࿸ᒙ
A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET
B) 使用对焦键将初始模式设为 ON 或 OFF
4-9. ऩૄᓍ‫࡝ݩ‬
ࠥ৖ถ፿᎖ᅓ߲ᓍ‫࡝ݩ‬
A) 使用 Tele/Wide 键选择子菜单中的 RETURN
B) 使用对焦键设置返回模式

17
 ᄂၐ࿸ᒙ
5. ᄂၐ࿸ᒙ
5-1. ፿ઓ‫ܪ‬ᄌ࿸ᒙ:
ࠥ৖ถ፿᎖Ᏼື෵ᒦመာᔈࢾፃ‫ܪ‬ᄌ
A) 使用 Tele/Wide 键在主菜单中设置 SPECIAL SET
B) 使用 Tele/Wide 键选择子菜单中的 USER TITLE
C) 使用 Tele / Wide 和对焦键设置标题位置和数据
5-2. ༹ᇠࣞࢯᑳ࿸ᒙ
A) 使用 Tele/Wide 键选择子菜单中的 SHARPNESS
B) 使用对焦键在 0 到 15 之间设置
5-3. न࿴஻࿸ᒙ
A) 使用 Tele/Wide 键选择子菜单中的 MIRROR
B) 使用对焦键设置模式为 ON OFF
5-4. ዕྻ࿸ᒙ
ࠥෝါ፿᎖੨‫ڹ‬ෝါ
A) 使用 Tele/Wide 键选择子菜单中的 COLOR
B) 使用对焦键设置模式为 ON OFF

18
ᄂၐ࿸ᒙ
5-5. ঌᒋ࿸ᒙ
ࠥෝါ፿᎖୓ዕྻਜ਼ೡࣞখ‫ࡵܤ‬ঌᒋ
A) 使用 Tele/Wide 键选择子菜单中的 COLOR
B) 使用对焦键设置模式为 ON OFF
5-6. ౑ᄴ‫ݛ‬࿸ᒙ
ࠥෝါ፿᎖ኀখᏐ௦ಭ።፿ࡼྻᄴ‫౑ࡒݛ‬
A) 使用 Tele/Wide 键选择子菜单中的 WIDEBURST
B) 使用对焦键设置模式为 ON OFF
5-7. ߱ဪ࿸ᒙ
ྙਫ߱ဪෝါ࿸ᆐ ON ఎ Ⴥᎌ SPECIAL ᄂၐ ৖ถ
୓‫ۻ‬খ‫ޣ߲ࡵܤ‬࿸ᒙ
A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET
B) 使用对焦键将初始模式设为 ON 或 OFF
5-8. ऩૄᓍ‫࡝ݩ‬
ࠥ৖ถ፿᎖ᅓ߲ᓍ‫࡝ݩ‬
A) 使用 Tele/Wide 键选择子菜单中的 RETURN
B) 使用对焦键设置返回模式

19
 Ꮵࣅଶ‫ހ‬
6. Ꮵࣅଶ‫ހ‬࿸ᒙ
6-1. ଶ‫ހ‬ෝါ࿸ᒙ
A) 使用 Tele/Wide 键在主菜单中设置 MOTION
B) 使用 Tele/Wide 键选择子菜单中的 DETECTION
C) 使用对焦键设置模式为 ON OFF
6-2. ଀ܰࢯᑳ࿸ᒙ
ࠥ৖ถ፿᎖ DETECTION ON ෝါ
A) 使用 Tele/Wide 键选择子菜单中的 LEVEL SET
B) 使用对焦键调整到某一敏感度
6-3. ߱ဪ࿸ᒙ
ྙਫ߱ဪෝါ࿸ᆐ ON ఎ Ⴥᎌ MOTION Ꮵࣅ ৖ถ୓
‫ۻ‬খ‫ޣ߲ࡵܤ‬࿸ᒙ
A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET
B) 使用对焦键将初始模式设为 ON 或 OFF
6-4. ऩૄᓍ‫࡝ݩ‬
ࠥ৖ถ፿᎖ᅓ߲ᓍ‫࡝ݩ‬ă
A) 使用 Tele/Wide 键选择子菜单中的 RETURN
B) 使用对焦键设置返回模式

20
F. OSD ࿸ᒙ
7. F. OSD ࿸ᒙ
7-1. ৖ถ࿸ᒙ
A) 使用 Tele/Wide 键在主菜单中设置 F. OSD
B) 使用 Tele/Wide 键在子菜单中选择您所需的模式
C) 使用 Tele / Wide 键和 Near/Far 键设置显示模式
*INITIAL SET ਜ਼ RETURN ࡼ‫ݛ‬ᒾᎧ༄ෂࡼ‫ݛ‬ᒾሤᄴ

21
 E. ැঢࣞ࿸ᒙ
8. E.ැঢࣞ࿸ᒙ: (భኡ)
8-1. E. ැঢࣞ࿸ᒙ
A) 使用 Tele/Wide 键选择子菜单中的 E.SENSITIVITY
B) 使用对焦键在子菜单中选择您所需的敏感度模式
* ෝါၿኔ: OFF-X2 AUTO-X4 AUTO-X8 AUTOX10AUTO-X16
AUTO- X32 AUTO
-OFF- X2 FIX-X4 FIX -X8 FIX -X10 FIX -X16 FIX - X32 FIX-OFF
8-2. ߱ဪ࿸ᒙ
ྙਫ߱ဪෝါ࿸ᆐ ON ఎ E.SENSITITY ৖ถ୓‫ۻ‬খ
‫ޣ߲ࡵܤ‬࿸ᒙ
A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET
B) 使用对焦键将初始模式设为 ON 或 OFF
8-3. ऩૄᓍ‫࡝ݩ‬
ࠥ৖ถ፿᎖ᅓ߲ᓍ‫࡝ݩ‬
A) 使用 Tele/Wide 键选择子菜单中的 RETURN
B) 使用对焦键设置返回模式

22
౑ࣅზपᆍ࿸ᒙ
9. ౑ࣅზपᆍ࿸ᒙ (భኡ)
9-1. ౑ࣅზपᆍ࿸ᒙ
A) 使用 Tele/Wide 键在主菜单中设置 WDR
B) 使用 Tele/Wide 键选择子菜单中的 WDR CONTROL
C) 使用对焦键在子菜单中选择您所需的 WDR 模式
* ෝါၿኔ : OFF -- ON -- AUTO
* WDR ᔈࣅෝါ፿᎖঱༓ࣞ۳਒ᄟୈሆ
9-2. ଀ܰࢯᑳ࿸ᒙ
ࠥ৖ถ፿᎖ࢯᑳ WDR ࡼᐐፄ
A) 使用 Tele/Wide 键选择子菜单中的 SENSITIVITY
B) 使用对焦键调整到某一敏感度
9-3. ߱ဪ࿸ᒙ
ྙਫ߱ဪෝါ࿸ᆐ ON ఎ WDR ౑ࣅზपᆍ ৖ถ୓
‫ۻ‬খ‫ޣ߲ࡵܤ‬࿸ᒙ
A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET
B) 使用对焦键将初始模式设为 ON 或 OFF
9-4. ऩૄᓍ‫࡝ݩ‬
ࠥ৖ถ፿᎖ᅓ߲ᓍ‫࡝ݩ‬
A) 使用 Tele/Wide 键选择子菜单中的 RETURN
B) 使用对焦键设置返回模式

23
 ື෵‫࡝ݩ‬መာ (OSD)
৖ถ OSD ৃါ ႁී
以下某些功能在操作摄像机时会
在屏幕上显示 5 秒钟后消失 1. 对焦模式 无显示 自动模式
☞ 手动 / 强制自动模式
2. 背光 无显示 背光关闭
"BL"显示 背光补偿开 / 自动背光补偿模式
3. 快门速度 无显示 普通快门 ( NTSC: 1/60)
1 2 3 6 PAL: 1/50)
"Ff"显示 无闪烁模式
1/125

1/10,000
4. 摄像机 ID 对每台摄像机设定识别码 可进行多点控
制 PC 控制 000~255
5. 变焦显示 DX 176 数码变焦模式
X 22 光学变焦模式
5 7 4

24
 ື෵‫࡝ݩ‬መာ (OSD)
৖ถ OSD ৃါ ႁී
6. 待机 在电源打开过程中摄像机处于待机状态
7. 白平衡控 自动白平衡
制模式 S特殊自动白平衡 根据外部光线变化的调整模式 可使用 RED
S
W ADJUST 和 BLUE ADJUST (0~255) 修改 R/B 值后 维护模式为
AUTO
室内白平衡预设 (3200°K)
室外白平衡预设 (5100°K)
M
W 手动白平衡调整 在手动模式下可使用 HUE 控制 (0 ~ 99).
P
W
强制自动白平衡 此模式打开时 白平衡自动调整 此模式关闭时
保留最后自动追踪的白平衡 手动

25
 ਖৃ
߅ስ࿸۸ 1/4" 隔行 CCD
NTST, 高分辨率 811(H) X 508(V) 410K
NTST, 普通分辨率 : 537(H) X 505(V) 270K
PAL, 高分辨率 : 795 (H) X 596 (V) 470K
PAL, 普通分辨率 : 537(H) X 597(V) 320K
ᄴ‫ݛ‬ᇹᄻ 内部同步
ၺຳॊ‫ܦ‬ൈ 大约 480 线 NTSC 高分辨率
320 线 NTSC 普通分辨率
480 线 PAL 高分辨率
320 线 PAL 普通分辨率
(屏幕中央)
஻ᄿ X 22 变焦 ( F 1.6 f = 3.9 ~ 85.8 mm ), 视频自动对焦
ၫ൩‫ܤ‬ୡ X 8 ( 总数码变焦 X 176 )
ᔢቃᑍී LVC-A910/912 SERIES : 1 Lux, AGC开
LVC-A911/913 SERIES : 0.01 Lux, X 32场累积
ቧᐅ‫܈‬ 大于48dB
ྸහᇹᄻ 2:1隔行
ྸහຫൈ(H) 15.734kHz(NTSC), 15.625kHz(PAL)
ྸහຫൈ(V) 59.94Hz(NTSC), 50Hz(PAL)

26
ਖৃ
ୡ௦ 0.01m (广角), 1.0m (远景)
ື෵‫࡝ݩ‬መာ (OSD) 开/关
࢟Ꮞገཇ DC 12V
၁ຫၒ߲ 复合输出75Ω 电阻 / Y,C 独立
৖੒ 5W
৔ᔫᆨࣞ 0°C - 45°C
৔ᔫဘࣞ 0% RH - 60% RH
߼ࡀᆨࣞ -20°C - 60°C, 0% RH - 85% RH
ߛࡁ 56.2mm(宽) x 64mm(高) x 101mm(厚)
ᒮ೟ 388g

ਖৃྦᎌৎখၭ‫ݙ‬഍ቲᄰᒀ

27