Specifications and Ordering Information

3300 5mm Transducer

Patents: 5,016,343; 5,126,664; 5,351,388; and 5,685,884

Description
Transducer System
The 3300 5mm Proximity Transducer System consists of:

• a 3300 5 mm probe 1, 2
• a 3300 XL extension cable (ref 141194-01)
• a 3300 Proximitor® Sensor 3, 4, 5 (ref 141194-01)

When combined with a 3300 XL Proximitor Sensor and XL extension

cable, the system provides an output voltage directly proportional to the
distance between the probe tip and the observed conductive surface. It is
capable of both static (position) and dynamic (vibration) measurements. Its
primary use is for vibration and position measurement applications on fluid-
film bearing machines, as well as Keyphasor® measurement and speed
measurement applications 6.

The system provides an accurate, stable signal output over a wide

temperature range. All 3300 XL Proximity Transducer Systems achieve this
level of performance while allowing complete interchangeability of probe,
extension cable, and Proximitor® Sensors. This eliminates the need for
individual component matching or bench calibration.

Proximity Probe
The 3300 5 mm probe reflects improvements over previous designs. A
patented TipLoc™ molding method provides a more robust bond between
the probe tip and the probe body.

Connectors
The 3300 5mm probe and 3300 XL extension cable have corrosion-resistant,
gold-plated brass ClickLoc™ connectors that require only finger-tight torque
(connectors will "click"). The specially engineered locking mechanism
prevents the connectors from loosening. These connectors do not require
any special tools for installation or removal.

BN Part Number 172036 Page 1 of 13

Revision B, November 2005
3300 5mm Probes and XL Extension Cables can be ordered XL Proximitor® Accepts one noncontacting 3300
with connector protectors already installed, or the connector Sensor Input: 5 mm Proximity Probe and XL
protectors supplied separately for installation in the field Extension Cable.
(such as when the cable must be run through restrictive
conduit). Connector protectors are recommended for all Power: Requires -17.5 Vdc to -26 Vdc at
installations and provide increased environmental protection7. 12 mA maximum consumption.
Operation at a more positive voltage
than -23.5 Vdc can result in reduced
Notes: linear range.
1. A 5 mm probe uses smaller physical packaging while providing the
same linear range as a 3300 XL 8 mm probe (ref 141194-01); Supply Sensitivity: Less than 2 mV change in output
however, it does not permit reduced sideview clearances or tip-to-tip voltage per volt change in input
spacing requirements compared to an XL 8 mm probe. It is used when voltage.
physical (not electrical) constraints preclude the use of an 8 mm probe,
such as mounting between thrust bearing pads or other constrained
spaces. When narrow sideview probes are required, use the 3300 XL Output resistance: 50 Ω
NSv™ probe and extension cable with the 3300 XL NSv Proximitor®
Sensor (refer to Specifications and Ordering Information p/n 147385- Probe dc resistance (R PROBE)
01).
2. XL 8 mm probes provide a thicker encapsulation of the probe coil in Probe Length (m) Resistance from the Center Conductor
the molded PPS plastic probe tip. This results in a more rugged probe. to the Outer Conductor (Ω)
The larger diameter of the probe body also provides a stronger, more 0.5 7.45 ± 0.50
robust case. Bently Nevada recommends the use of XL 8 mm probes
when possible to provide optimal robustness against physical abuse. 1.0 7.59 ± 0.50
3. A 3300 XL Proximitor Sensor is available and provides many 1.5 7.73 ± 0.50
improvements over the non-XL version. It is electrically and 2.0
mechanically interchangeable with the non-XL version. Although the
7.88 ± 0.50
packaging of the 3300 XL Proximitor® Sensor differs from its 5.0 8.73 ± 0.70
predecessor, its design allows it to fit in the same 4-hole mounting 9.0 9.87 ± 0.90
pattern when used with the 4-hole mounting base, and to fit within the
same mounting space specifications (when minimum permissible cable
bend radius is observed). Consult Specifications and Ordering Extension cable dc resistance
Information (p/n 141194-01) or Bently Nevada Sales and Service Length of Resistance from Resistance from
Professional for more information. Extension Center Conductor to Outer Conductor to
4. Us of XL components with 3300 5mm Probes will limit system
performance to the specifications for the non-XL 3300 system. Cable Center Conductor Outer Conductor
5. The factory supplies Proximitor® Sensors calibrated by default to AISI (RCORE) (Ω) (RJACKET) (Ω)
4140 steel. Calibration to other target materials is available upon
3.0 0.66 ± 0.10 0.20 ± 0.04
request.
6. When considering this transducer system for tachometer or overspeed 3.5 0.77 ± 0.12 0.23 ± 0.05
measurements, consult www.bently.com for the application note 4.0 0.88 ± 0.13 0.26 ± 0.05
regarding the use of eddy current proximity probes for over speed
protection. 4.5 0.99 ± 0.15 0.30 ± 0.06
7. Silicone tape is also provided with each 3300 XL extension cable and 7.0 1.54 ± 0.23 0.46 ± 0.09
can be used instead of connector protectors. Silicone tape is not 7.5 1.65 ± 0.25 0.49 ± 0.10
recommended in applications where the probe-to-extension cable
connection will be exposed to turbine oil. 8.0 1.76 ± 0.26 0.53 ± 0.11
8.5 1.87 ± 0.28 0.56 ± 0.11

Note: Outer conductor refers to the shielded conductor that is attached to

Specifications the connector, not the armor braid.

Unless otherwise noted, the following specifications are for a Extension cable 69.9 pF/m (21.3 pF/ft) typical.
proximity transducer system between +18° C and +27° C capacitance:
(+64° F to +80° F) with a -24 Vdc power supply, a 10 kΩ
load, an AISI 4140 steel target, and a probe gapped at 1.27 Field Wiring: Recommend using three-conductor
shielded triad cable 0.2mm to
mm (50 mils).
1.5mm (16 AWG to 24 AWG). 305
metres (1,000 feet) maximum length
between 3300 XL Proximity
Electrical
Transducer and monitor. Consult
Performance Specification 155687
for signal rolloff at high frequencies

BN Part Number 172036 Page 2 of 13

Revision B, November 2005
 when using longer field wiring When gapped at the center of the linear range, the interaction
lengths or external safety barriers between two separate transducer systems (cross-talk) will be
located some distance from the less than 50 mV on shaft diameters of at least 50 mm (2 in)
monitoring system. or greater. Maintain a minimum separation of transducer tips,
generally at least 40 mm (1.6 in) for axial position
Linear Range: 2 mm (80 mils). Linear range begins measurements or 38 mm (1.5 in) for radial vibration
at approximately 0.25 mm (10 mils) measurements to limit cross-talk to 50 mV or less. Radial
from target and is from 0.25 to vibration or position measurements on shaft diameters
2.3 mm (10 to 90 mils). smaller than 76.2 mm (3 in) will generally result in a change
in scale factor. Consult Performance Specification 155687
Recommended Gap 1.27 mm (50 mils). for additional information.
Setting:
Effects of 60 Hz Magnetic Fields Up to 300 Gauss
Incremental Scale 7.87 V/mm (200 mV/mil) ±6.5% (5 metre system):
Factor: typical, including interchangeability Output voltage in mil pp/gauss:
error when measured in increments Gap XL Probe XL Ext.
of 0.25 mm (10 mils) over the linear Proximitor® Cable
range. Sensor
10 mil 0.0119 0.0004 0.0004
Deviation from best fit Less than ±0.038 mm (±1.5 mil) 50 mil 0.0131 0.0014 0.0014
straight line (DSL): typical deviation from best fit straight 90 mil 0.0133 0.0045 0.0045
line.
Electrical Complies with the European CE
Probe Temperature Over probe temperature range of
Certification: mark.
Stability (typical): -35° C to +177° C (-31° F to +350°
F), the incremental scale factor Multiple approvals for hazardous
remains within ±10% of 7.87 V/mm
Hazardous Area areas certified by Canadian
(200 mV/mil) and the deviation from
Approvals Standards Association
the best fit straight line remains
(CSA/NRTL/C) in North America
within ±0.076 mm (±3 mils). and by Baseefa (2001) in Europe.
Frequency 0 to 10 kHz: +0, -3 dB, with up to North America: Ex ia IIC T4/T5 for Class I Zone 0 or
Response: 305 metres (1000 feet) of field Class 1 Division 1; Groups A, B, C,
wiring. and D, when installed with
intrinsically safe zener barriers per
Minimum Target Size: 15.2 mm (0.6 in) diameter drawing 141092, or when installed
(flat target). with galvanic isolators.
Shaft Diameter Ex nA IIC T4/T5 for Class I Zone 2
or Class 1 Division 2, Groups A, B,
Minimum: 50.8 mm (2 in) C, and D when installed without
barriers per drawing 140979
Recommended 76.2 mm (3 in) T5 @ Ta = -35° C to 85° C.
minimum: T4 @ Ta = -51° C to +100° C

Europe: II 1 G EEx ia IIC T4/T5 EC

certificate numberBAS99ATEX1101,
when installed per per drawing
141092.

II 3 G EEx nA II T4/T5. EC
certificate number
BAS99ATEX3100U, when installed
per drawing 140979.

BN Part Number 172036 Page 3 of 13

Revision B, November 2005
 T5 @ Ta = -35° C to 85° C. Ex ia IIC Temperature Classification
T4 @ Ta = -51° C to +100° C per below.

T1: -51º C to +232º C

IEC Ex: 3300 XL Proximitor® Sensor, T2: -51º C to +177º C
ia T3: -51º C to +120º C
T4: -51º C to +80º C
IECEx BAS04.0055X T5: -51º C to +40º C
Ex ia IIC T4 / T5 (-51ºC = Ta =
+100ºC / -35ºC = Ta = +85ºC) Ui = -28V Ci = 1.5nF

Terminal Block Connections Ii = 140mA Li = 200µH

Ui= -28V Ci = 0 Pi =0.84W

Ii= 140mA Li =10µH 3300 5mm Eddy Current

Probe, nA
Pi= 0.84W
IECEx BAS04.0058X
Coaxial Connection
Ex nA II Temperature
Ui = -28V Ci= 5.7nF Classification per the
Ii = 140mA Li = 0.85mH temperature classifications
above.
Pi = 0.84W
Must be supplied from a voltage
Load Parameters limited source.
The capacitance and either the EEx nA for Zone 2, Group IIC,
inductance or the inductance to EC certificate number
resistance (L/R) ratio of the load BAS99ATEX3100U.
connected to the probe coaxial
terminal must not exceed the
following values: Mechanical

Probe Tip Material: Polyphenylene sulfide (PPS).

Probe Case Material: AISI 303 or 304 stainless steel

(SST).

Probe Cable: 75 Ohm triaxial, fluoroethylene

propylene (FEP) insulated probe
cable in the following lengths: 0.5, 1,
2, 5, or 9 metres.
3300 XL Proximitor® Sensor,
nA
System Length: 5 or 9 metres including extension
IECEx BAS04.0057X
cable.
Ex nA II T4 / T5 (-51º C = Ta =
+100º C / -35º C = Ta = +85º C)
The terminals must be provided
Extension Cable 75 Ω triaxial, fluoroethylene
with a level of protection of at
Material propylene (FEP) insulated.
least IP54.
Ui = -28V
Probe and Extension Flexible AISI 302 or 304 SST with
Cable Armor FEP outer jacket
3300 5mm Eddy Current
Probe, ia
IECEx BAS04.0056

BN Part Number 172036 Page 4 of 13

Revision B, November 2005
 Note: Exposing the probe to temperatures below -34°C (-30°F) may cause
premature failure of the pressure seal.
Tensile Strength
Extension Cable -51° C to +177° C (-60° F to +351°
Temperature Range: F) for standard extension cable (Ref.
5 mm probe: 222 N (50 lbf) probe case to probe 141194-01).
lead. 222 N (50 lbf) probe lead to
extension cable connectors.

Probe Pressure:
Connector material: Gold-plated brass or gold-plated 3300 5 mm probes are designed
beryllium copper. to seal differential pressure
between the probe tip and case.
The probe sealing material
Probe case torque: Recommended torque: consists of a fluorocarbon O-
2.8 N·m (25 in·lb) ring. Probes are not pressure
Maximum torque: tested prior to shipment.
8.5 N·m (75 in·lb) Contact our custom design
department if you require a test
of the pressure seal for your
application.
Connector-to-connector torque
Note: It is the responsibility of the
customer or user to ensure that all liquids
Recommended See table below. and gases are contained and safely
torque: controlled should leakage occur from a
proximity probe. In addition, solutions with
Maximum torque: 0.565 N•m (5 in•ft) high or low pH values may erode the tip
assembly of the probe causing media
leakage into surrounding areas. Bently
Connector Type Tightening Instructions Nevada, LLC will not be held responsible
Two 3300 XL gold "click" Finger tight for any damages resulting from leaking
type connectors 3300 5 mm proximity probes. In addition,
One non-XL stainless steel Finger tight plus 1/8 turn 3300 5 mm proximity probes will not be
replaced under the service plan due to
connector and one using pliers probe leakage.
3300 XL connector

Minimum Cable Bend 25.4 mm (1.0 in).

Radius:

Total System Weight: 0.71 kg (1.6 lbm), typical.

3300 5mm Probe: 323 g (11.39 oz). Patents: Components or procedures

5,016,343; 5,126,664; described in these patents apply to
XL Extension 5,351,388; and this product
Cable: 34 g/m (0.4 oz/ft) 5,685,884.
103 g/m (1.5 oz/ft) (armored)

XL Proximitor® 246 g (8.7 oz)

Sensor: Ordering Information

Environmental Limits

Probe Temperature
Range: -35° C to +177° C (-31° F to +351°
F)

BN Part Number 172036 Page 5 of 13

Revision B, November 2005
3300 5 mm Proximity Probes A: Unthreaded Note: Unthreaded length must be at least
20 mm less than the case length.
330171 3300 5 mm Probe, 1/4-28 UNF thread, without Length Option
armor
330172 3300 5 mm Probe, 1/4-28 UNF thread, with armor Order in increments of 10 mm.
Length configuration:
Part Number-AXX-BXX-CXX-DXX-EXX Maximum unthreaded length: 230
Option Descriptions mm = 2 3.
Minimum unthreaded length: 0.0
A: Unthreaded Note: Unthreaded length must be at least mm = 0 0.
Length Option 0.8 in less than the case length. Example: 0 6 = 60 mm.
Order in increments of 0.1in
Length configurations: B: Overall Case Order in increments of 10 mm.
Maximum unthreaded length: 8.8 in Length Option Metric thread configurations:
= 8 8. Maximum length: 250 mm = 2 5.
Minimum unthreaded length: 0.0 in Minimum length: 20 mm = 0 2.
= 0 0. Examples: 0 6 = 60 mm.
Example: 0 4 = 0.4 in
C: Total Length 05 0.5 metre (1.6 feet)
B: Overall Case Order in increments of 0.1 in Option 10 1.0 metre (3.3 feet)
Length Option Threaded length configurations: 20 2.0 metres (6.6 feet)
Maximum case length: 9.6 in = 9 6. 50 5.0 metres (16.4 feet) 1
Minimum case length: 0.8 in = 0 8. 90 9.0 metres (29.5 feet)
Example: 2 4 = 2.4 in
D: Connector Option 0 1 Miniature coaxial ClickLoc™
C: Total Length 05 0.5 metre (1.6 feet) connector with connector
Option 10 1.0 metre (3.3 feet) protector, standard cable
20 2.0 metres (6.6 feet) 0 2 Miniature coaxial ClickLoc™
50 5.0 metres (16.4 feet) 1 connector, standard cable
90 9.0 metres (29.5 feet)
E: Agency Approval 0 0 Not required
D: Connector Option 0 1 Miniature coaxial ClickLoc™ Option 0 5 Multiple Approvals
connector with connector
protector, standard cable
0 2 Miniature coaxial ClickLoc™
connector, standard cable
3300 XL Proximitor Sensor
E: Agency Approval 0 0 Not required See 141194-01. Make sure that the extension cable
Option 0 5 Multiple Approvals length and the probe length, when added together, equal
the Proximitor® Sensor total length.
3300 5 mm Proximity Probes, Metric
330173 3300 5 mm Probe, M8 x 1 thread, without armor
330174 3300 5 mm Probe, M8 x 1 thread, with armor

Part Number-AXX-BXX-CXX-DXX-EXX
Option Descriptions 3300 XL Extension Cable
See 141194-01Make sure that the extension cable length and
the probe length, when added together, equal the
Proximitor® Sensor total length.

Accessories
141078-01 Manual

BN Part Number 172036 Page 6 of 13

Revision B, November 2005
02120015 Bulk field wire. 1.0 mm2 (18 AWG),
3-conductor, twisted, shielded cable 40113-03 Connector Protector Kit for 3300 5
for connections between Connector Protector mm probes, including connector
Proximitor® Sensor and monitor. Kit protectors and installation tools.

136536-01 Makes connector protector kits

Connector Protector purchased prior to 1998 compatible
Adapter with ClickLoc™ extension cable
Aluminum probe mounting bracket connectors.
137492 -AXX
Option Descriptions 40180-03 Package containing 10 pairs of 75
Connector Protectors ohm Coaxial Connector Protectors.
A: Thread size
0 2 1/4-28 03839410 Placed onto the extension cable;
0 3 M8 x 1 75 ohm Triaxial/95 attaches to the female connector
ohm Coaxial Male protector on the 5 mm probe to
Connector Protector provide environmental protection of
The aluminum probe threaded connectors.
mounting bracket is the standard
mounting bracket for most 3300 5
mm probe installations. The -02 03800001 Placed onto 3300 5 mm probe
option is supplied with two 10-24 75 ohm Coaxial leads; attaches to the male
UNC-2A mounting screws. The -03 Female Connector connector protector on the extension
option is supplied with two M5 x 0.8- Protector cable to provide environmental
6g mounting screws. The mounting protection of connectors.
screws have pre-drilled holes for
safety wire.

Phenolic probe mounting bracket

27474 -AXX 163356 Includes one set of multi-connector
Option Descriptions Connector Crimp inserts and connector installation
Tool Kit instructions. Compatible only with
A: Thread size 0 2 1/4-28 330153 connector kits or with
0 3 M8 x 1 probes shipped in 2003 or later with
ClickLoc™ connectors uninstalled.
The phenolic mounting bracket is Supplied with carrying case.
recommended if additional electric
isolation from the mounting location
is required (as in some generator 75 Ω ClickLoc™
and electrical motor bearing Connector Kit
locations). The -02 option is 330153-AA
supplied with two 10-24 UNC-2A Option Descriptions
mounting screws. The -03 option is 0 2 One ClickLoc™ male
supplied with two M5 x 0.8-6g connector for 3300 XL 5 mm and 8
mounting screws. The mounting mm extension cable.
screws have pre-drilled holes for 0 3 One ClickLoc™ female
safety wire. connector for 3300 XL 5 mm and 8
mm extension cable.
0 4 One ClickLoc™ male
03200006 9.1 metre (10 yard) roll of silicone connector for 3300 5 mm probe.
Silicone self-fusing tape to protect connectors. It is
tape easy to install and provides
excellent electrical isolation and 75 Ω ClickLoc™ Connector Kit for

BN Part Number 172036 Page 7 of 13

Revision B, November 2005
 3300 series probes and extension
cables. Each kit contains one color-
coded sleeve per connector.

 2005 Bently Nevada®, LLC

ClickLoc™, , Keyphasor®, NSv™, Proximitor®, TipLoc™, and the Orbit logo are trademarks of Bently Nevada, LLC.

BN Part Number 172036 Page 8 of 13

Revision B, November 2005
Graphs

Figure 1 - Typical 3300 5 mm probe and 1 metre of cable at high and low temperatures (XL
Proximitor® Sensor and XL extension cable are at 25°C)

BN Part Number 172036 Page 9 of 13

Revision B, November 2005
 Figure 2 - 3300 5 metre XL Proximitor® Sensor at high temperatures (3300 5mm probe and XL extension cable at 25° C)

BN Part Number 172036 Page 10 of 13

Revision B, November 2005
Dimensional diagrams

1 Probe tip, 5.2 (0.21) diameter 7 3.2 (0.13)

11.1 (7/16) for 1/4-28 threads3
2 8 Unthreaded length “A”
13.0 (0.51) for M8 threads3
3 Case thread 9 Case length “B”
5.6 (7/32) wrench flats for 1/4-28 threads
4 7.0 (0.28) for M8 threads 10 6.0 (0.235) maximum
4 each
75 ohm cable, 2.8 (0.11) maximum outside
5 diameter, 7.6 (0.3) outside diameter of armor, 11 Total length8 “C”, +30%, -0%
9.0 (0.35) maximum diameter of armor ferrule
Miniature male coaxial connector, 7.23 (0.285)
6
outside diameter maximum “D”

Figure 3 - 3300 5 mm Proximity Probes, Standard Mount3

330171, 1/4-28 UNF-2A, without armor7

330172, 1/4-28 UNF-2A, with armor6

330173, M8X1 thread, without armor7

330174, M8X1 thread, with armor6

BN Part Number 172036 Page 11 of 13

Revision B, November 2005
 1 12 (0.49) diameter maximum 3 51.1 (2.01) maximum
2 36.3 (1.43) maximum 4 Connector protector (flurosilicone material)

Figure 4 - Installed Connector Protectors

1 7.2 (0.285) maximum diameter 5 Stainless steel ferrules, 8.4 (0.33) diameter
2 Miniature male coaxial connector 6 FEP or PFA insulated triaxial cable
FEP or PFA coated armor6. Armor length: 300
3 7 Miniature female coaxial connector
(11.8) less than cable length
75 ohm cable
3.7 (0.15) maximum outside diameter
4 3.9 (0.16) maximum diameter for FluidLoc® cable 8 Cable length +20%, -0%
7.6 (0.30) maximum outside diameter of armor
9.0 (0.35) maximum diameter of armor ferrule

Figure 5 - 3300 XL Extension Cable

330130, 3300 XL Extension Cable (FEP armor and insulation)

BN Part Number 172036 Page 12 of 13

Revision B, November 2005
Notes:
1. All dimensions are in millimetres (inches) unless otherwise noted.
2. Deleted
3. Standard mount 5 mm probes supplied with 13 mm or 7/16-in lock nut.
4. Deleted
5. Letters inside quotation marks refer to probe ordering options.
6. Stainless steel armor is supplied with FEP outer jacket for standard probes, PFA outer jacket for ETR probes.
7. FEP jacket is standard non-armored portion of the cable for standard probes, PFA jacket on non-armored portion for ETR probes.
8. Probes ordered with 5 or 9 metre integral cables have a length tolerance of +20%, -0%.
9. Five metre probes are designed for use with the five metre Proximitor® Sensor only.

BN Part Number 172036 Page 13 of 13

Revision B, November 2005