CDMA - Quick Guide

04/10/2023, 11:21 CDMA - Quick Guide
Menu Search tutorials, courses and ebooks...

Login
Home
Coding
HTMLGround
CSS Javascript SQL Python Java C C++
Jobs
CDMA - Quick Guide
Whiteboard
Tools
CDMA - Introduction
What is CDMA?
Code Division Multiple Access (CDMA) is a digital cellular technology used for
mobile communication. CDMA is the base on which access methods such as
cdmaOne, CDMA2000, and WCDMA are built. CDMA cellular systems are
deemed superior to FDMA and TDMA, which is why CDMA plays a critical role in
building efficient, robust, and secure radio communication systems.
A Simple Analogy
Let’s take a simple analogy to understand the concept of CDMA. Assume we

have a few students gathered in a classroom who would like to talk to each
other simultaneously. Nothing would be audible if everyone starts speaking at
the same time. Either they must take turns to speak or use different languages
to communicate.
The second option is quite similar to CDMA — students speaking the same
language can understand each other, while other languages are perceived as
noise and rejected. Similarly, in radio CDMA, each group of users is given a
shared code. Many codes occupy the same channel, but only those users
associated with a particular code can communicate.
https://www.tutorialspoint.com/cdma/cdma_quick_guide.htm 1/47
04/10/2023, 11:21 CDMA - Quick Guide
Salient Features of CDMA
CDMA, which is based on the spread spectrum technique has following salient
features −
In CDMA, every channel uses the full available spectrum.

Individual conversations are encoded with a pseudo-random digital
sequence and then transmitted using a wide frequency range.
CDMA consistently provides better capacity for voice and data
communications, allowing more subscribers to connect at any given
time.
CDMA is the common platform on which 3G technologies are built. For
3G, CDMA uses 1x EV-DO and EV-DV.
Third Generation Standards

CDMA2000 uses Frequency Division Duplexing-Multicarrier (FDD-MC) mode.
Here, multicarrier implies N × 1.25 MHz channels overlaid on N existing IS-95
carriers or deployed on unoccupied spectrum. CDMA2000 includes −
1x — uses a spreading rate of 1.2288 Mcps.
3x — uses a spreading rate of 3 × 1.2288 Mcps or 3.6864 Mcps.

1xEV-DO (1x Evolution – Data Optimized) — uses a spreading rate of
1.2288 Mcps, optimized for the data.
WCDMA/FDD-DS — Wideband CDMA (WCDMA) Frequency Division

Duplexing-Direct Sequence spreading (FDD-DS) mode. This has a single
5 MHz channel. WCDMA uses a single carrier per channel and employs a
spreading rate of 3.84 Mcps.
CDMA Development Group (CDG)

The CDMA Development Group (CDG), founded in December 1993, is an
international consortium of companies. It works together to lead the growth
and evolution of advanced wireless telecommunication systems.
04/10/2023, 11:21 CDMA - Quick Guide
CDG is comprised of service providers, infrastructure manufacturers, device

vendors, test equipment vendors, application developers, and content
providers. Its members jointly define the technical requirements for the
development of complementary systems CDMA2000 and 4G. Further, the
interoperability with other emerging wireless technologies are meant to
increase the availability of wireless products and services to consumers and
businesses worldwide.
IMT-2000 System
CDMA - Channels
CDMA channels can be broadly categorized as Forward channel and Reverse
channel. This chapter explains the functionalities of these channels.
Forward Channel
The Forward channel is the direction of the communication or mobile-to-cell
downlink path. It includes the following channels −
Pilot Channel − Pilot channel is a reference channel. It uses the mobile

station to acquire the time and as a phase reference for coherent
demodulation. It is continuously transmitted by each base station on
each active CDMA frequency. And, each mobile station tracks this signal
continuously.
04/10/2023, 11:21 CDMA - Quick Guide
Sync Channel − Synchronization channel carries a single, repeating

message, which gives the information about the time and system
configuration to the mobile station. Likewise, the mobile station can
have the exact system time by the means of synchronizing to the short
code.
Paging Channel − Paging Channel’s main objective is to send out

pages, that is, notifications of incoming calls, to the mobile stations. The
base station uses these pages to transmit system overhead information
and mobile station specific messages.
Forward Traffic Channel − Forward Traffic Channels are code

channels. It is used to assign calls, usually voice and signaling traffic to
the individual users.
Reverse Channel
The Reverse channel is the mobile-to-cell direction of communication or the
uplink path. It consists of the following channels −
Access Channel − Access channel is used by mobile stations to

establish a communication with the base station or to answer Paging
Channel messages. The access channel is used for short signaling
message exchanges such as call-ups, responses to pages and
registrations.
Reverse Traffic Channel − Reverse traffic channel is used by the
individual users in their actual calls to transmit traffic from a single
mobile station to one or more base stations.
04/10/2023, 11:21 CDMA - Quick Guide
CDMA - Multiple Access Methods

The possibility to operate in either FDD or TDD mode is allowed for efficient use
of available spectrum according to frequency allocation in different regions.
Frequency Division Duplex

A duplex method whereby the Uplink and the Downlink transmissions use two
separate frequency bands −
Uplink − 1920 MHz to 1980 MHz

Downlink − 2110 MHz to 2170 MHz
Bandwidth − Each carrier is located on the center of a 5 MHz wide

band
Channel Separation
Nominal value of 5 MHz that can be adjusted.
Channel Raster
200 kHz (center frequency must be a multiple of 200 kHz).
Tx-Rx Frequency Separation
Nominal value of 190 MHz. This value can be either fixed or variable (minimum
of 134.8 and maximum of 245.2 MHz).
Channel Number
The carrier frequency is designated by the UTRA Absolute Radio Frequency

Channel Number (UARFCN). This number is sent by the network (for the uplink
and downlink) on the BCCH logical channel and is defined by Nu = 5 *
(Frequency uplink MHz) and ND = 5 * (Frequency downlink MHz).
Time Division Duplex
04/10/2023, 11:21 CDMA - Quick Guide
Time division duplex is a technique by which the Uplink and the Downlink
transmissions are carried over the same frequency by using synchronized time
intervals. The carrier uses a 5 MHz band, although there is a low chip rate
solution under study by the 3GPP (1.28 Mcps). The available frequency bands
for TDD will be 1900–1920 MHz and 2010 – 2025 MHz.
Duplex Methods of Radio Links
In case of Time Division Duplex, the forward link frequency is same as the
reverse link frequency. In each link, signals are transmitted continuously in
turns − just like a ping-pong game.
Example of TDD System
TDD uses a single frequency band for both to transmit and to receive. Further,
it shares the band by assigning alternate timeslots for transmitting and
receiving operations. The information to be transmitted can be voice, video, or
computer data in bit-serial format. Each time interval can be 1 byte long or
may be a part of several bytes.
TDD alternates the transmission and reception station data over time.
Timeslots can be of variable length. Due to the nature of high-speed data, the
04/10/2023, 11:21 CDMA - Quick Guide
communicating parties cannot mean that the transmissions are intermittent.

Transmissions that appear as simultaneous are actually competing each other.
Digitally converted into analog voice, no one can say that it is not a full duplex.
In some TDD systems, alternative time intervals are of same duration or

having both DL and UL; however, the system does not need to be symmetric
50/50. The system may be asymmetrical as required.
For example, while accessing the Internet, the download speed is usually
higher than the upload speed. Most of the equipment work on asynchronous
mode where the download speed is higher than the upload speed. When the
download speed is higher than the upload speed, less timeslots are needed for
uploading. Some TDD formats offer dynamic bandwidth allocation when the
number of time intervals or durations is changed on the fly as needed.
The real advantage of TDD is that it is only a single channel of the frequency
spectrum and it doesn’t require band guards or channel separations as the
intervals take place using timeslots. The disadvantage is that the successful
implementation of TDD requires a timing system. The precise timing to both
the transmitter and the receiver is needed to ensure that the time intervals do
not overlap or interfere with another.
Timing is often synchronized to GPS atomic clock standards specific derivative.

The guard time is also needed between timeslots to avoid duplication. This time
is generally equal to the transmission-reception processing time (transmission-
reception switching time) and the transmission delays (latency) on the
communications channel.
Frequency Division Duplex
04/10/2023, 11:21 CDMA - Quick Guide
In Frequency Division Duplex (FDD), the forward link frequency is not the same
as the reverse link frequency. In each link, signals are continuously transmitted
in parallel.
Example of FDD System
FDD requires two symmetrical segments of spectrum for the uplink and
downlink channels.
In a cell phone with a transmitter and receiver, operating simultaneously in

such close proximity, the receiver has to filter as much of the signal from the
transmitter as possible. More separation of the spectrum, the most effective
filters.
FDD uses a lot of frequency spectrum, generally twice of the required TDD
spectrum. In addition, there must be adequate spectrum separation between
transmission and reception of the channels. These bands keep saying − it
cannot be used, they are unnecessary. Given the scarcity and cost of the
spectrum, they are real disadvantages.
Use of FDD
04/10/2023, 11:21 CDMA - Quick Guide
FDD is widely used in different cellular telephone systems. In some systems,

the band 869-894 MHz is used as the downlink (DL) spectrum from the cell site
tower to the device. And, the band 824-849 MHz is used as the uplink (UL)
spectrum of the handset at the cell site.
FDD also works on a cable where transmit and receive channels are given
different parts of the cable spectrum, as in cable TV systems. And, filters are
used to keep the channels separate.
Disadvantage of FDD
The drawback of FDD is that it does not allow special techniques like multiple
antennas, multiple input-output (MIMO), and beamforming. These technologies
are an essential element of the new strategies Long Term Evolution (LTE) 4G
cell phone to increase the data rate. It is difficult to make broad enough
bandwidth to cover both sets of antenna spectrum. Circuit complex dynamic
adjustment is required.
Multiple Access Methods

The radio channel is a communication medium shared by several users in a
geographic area. Mobile stations are in competition with one another for the
frequency resource to transmit their information flow. Without other measures
to control concurrent access of several users, collisions can occur. Since
collisions are undesirable for connectionoriented communication such as mobile
phones, personal/mobile subscriber stations need to be allocated the dedicated
channels on request.
04/10/2023, 11:21 CDMA - Quick Guide
The mobile communication, sharing wireless resources on all users, must be

communicated to identify the user. While identifying the user, it is referred to
as "multiple access" (Multiple Access) that is receiving a radio wave of a
number of transmitting stations in a receiving station (as shown in the
following image).
FDMA - Technology
Frequency Division Multiple Access (FDMA) is one of the most common
analogue multiple access methods. The frequency band is divided into channels
of equal bandwidth so that each conversation is carried on a different
frequency (as shown in the figure below).
FDMA Overview
In FDMA method, guard bands are used between the adjacent signal spectra to
minimize crosstalk between the channels. A specific frequency band is given to
one person, and it will received by identifying each of the frequency on the
receiving end. It is often used in the first generation of analog mobile phone.
Advantages of FDMA
As FDMA systems use low bit rates (large symbol time) compared to average
delay spread, it offers the following advantages −
Reduces the bit rate information and the use of efficient numerical codes
increases the capacity.
04/10/2023, 11:21 CDMA - Quick Guide
It reduces the cost and lowers the inter symbol interference (ISI)
Equalization is not necessary.
An FDMA system can be easily implemented. A system can be

configured so that the improvements in terms of speech encoder and bit
rate reduction may be easily incorporated.
Since the transmission is continuous, less number of bits are required
for synchronization and framing.
Disadvantages of FDMA
Although FDMA offers several advantages, it has a few drawbacks as well,
which are listed below −
It does not differ significantly from analog systems; improving the

capacity depends on the signal-to-interference reduction, or a signal-to-
noise ratio (SNR).
The maximum flow rate per channel is fixed and small.

Guard bands lead to a waste of capacity.
Hardware implies narrowband filters, which cannot be realized in VLSI
and therefore increases the cost.
TDMA - Technology
Time Division Multiple Access (TDMA) is a digital cellular telephone
communication technology. It facilitates many users to share the same
frequency without interference. Its technology divides a signal into different
timeslots, and increases the data carrying capacity.
TDMA Overview
Time Division Multiple Access (TDMA) is a complex technology, because it
requires an accurate synchronization between the transmitter and the receiver.
TDMA is used in digital mobile radio systems. The individual mobile stations
cyclically assign a frequency for the exclusive use of a time interval.
04/10/2023, 11:21 CDMA - Quick Guide
In most of the cases, the entire system bandwidth for an interval of time is not
assigned to a station. However, the frequency of the system is divided into sub-
bands, and TDMA is used for the multiple access in each sub-band. Sub-bands
are known as carrier frequencies. The mobile system that uses this
technique is referred as the multi-carrier systems.
In the following example, the frequency band has been shared by three users.
Each user is assigned definite timeslots to send and receive data. In this
example, user ‘B’ sends after user ‘A,’ and user ‘C’ sends thereafter. In this
way, the peak power becomes a problem and larger by the burst
communication.
FDMA and TDMA

This is a multi-carrier TDMA system. A 25 MHz frequency range holds 124
single chains (carrier frequencies 200) bandwidth of each kHz; each of these
frequency channels contains 8 TDMA conversation channels. Thus, the
sequence of timeslots and frequencies assigned to a mobile station is the
physical channels of a TDMA system. In each timeslot, the mobile station
transmits a data packet.
The period of time assigned to a timeslot for a mobile station also determines
the number of TDMA channels on a carrier frequency. The period of timeslots
are combined in a so-called TDMA frame. TDMA signal transmitted on a carrier
frequency usually requires more bandwidth than FDMA signal. Due to the use
of multiple times, the gross data rate should be even higher.
Advantages of TDMA
Here is a list of few notable advantages of TDMA −
04/10/2023, 11:21 CDMA - Quick Guide
Permits flexible rates (i.e. several slots can be assigned to a user, for
example, each time interval translates 32Kbps, a user is assigned two
64 Kbps slots per frame).
Can withstand gusty or variable bit rate traffic. Number of slots allocated
to a user can be changed frame by frame (for example, two slots in the
frame 1, three slots in the frame 2, one slot in the frame 3, frame 0 of
the notches 4, etc.).
No guard band required for the wideband system.
No narrowband filter required for the wideband system.
Disadvantages of TDMA
The disadvantages of TDMA are as follow −
High data rates of broadband systems require complex equalization.

Due to the burst mode, a large number of additional bits are required
for synchronization and supervision.
Call time is needed in each slot to accommodate time to inaccuracies

(due to clock instability).
Electronics operating at high bit rates increase energy consumption.
Complex signal processing is required to synchronize within short slots.
CDMA - Technology
Code Division Multiple Access (CDMA) is a sort of multiplexing that facilitates
various signals to occupy a single transmission channel. It optimizes the use of
available bandwidth. The technology is commonly used in ultra-high-frequency
(UHF) cellular telephone systems, bands ranging between the 800-MHz and
1.9-GHz.
CDMA Overview
Code Division Multiple Access system is very different from time and frequency
multiplexing. In this system, a user has access to the whole bandwidth for the
entire duration. The basic principle is that different CDMA codes are used to
distinguish among the different users.
04/10/2023, 11:21 CDMA - Quick Guide
Techniques generally used are direct sequence spread spectrum modulation

(DS-CDMA), frequency hopping or mixed CDMA detection (JDCDMA). Here, a
signal is generated which extends over a wide bandwidth. A code called
spreading code is used to perform this action. Using a group of codes, which
are orthogonal to each other, it is possible to select a signal with a given code
in the presence of many other signals with different orthogonal codes.
How Does CDMA Work?

CDMA allows up to 61 concurrent users in a 1.2288 MHz channel by processing
each voice packet with two PN codes. There are 64 Walsh codes available to
differentiate between calls and theoretical limits. Operational limits and quality
issues will reduce the maximum number of calls somewhat lower than this
value.
In fact, many different "signals" baseband with different spreading codes can
be modulated on the same carrier to allow many different users to be
supported. Using different orthogonal codes, interference between the signals
is minimal. Conversely, when signals are received from several mobile stations,
the base station is capable of isolating each as they have different orthogonal
spreading codes.
The following figure shows the technicality of the CDMA system. During the
propagation, we mixed the signals of all users, but by that you use the same
code as the code that was used at the time of sending the receiving side. You
can take out only the signal of each user.
04/10/2023, 11:21 CDMA - Quick Guide
CDMA Capacity
The factors deciding the CDMA capacity are −
Processing Gain
Signal to Noise Ratio
Voice Activity Factor
Frequency Reuse Efficiency
Capacity in CDMA is soft, CDMA has all users on each frequency and users are
separated by code. This means, CDMA operates in the presence of noise and
interference.
In addition, neighboring cells use the same frequencies, which means no re-
use. So, CDMA capacity calculations should be very simple. No code channel in
a cell, multiplied by no cell. But it is not that simple. Although not available
code channels are 64, it may not be possible to use a single time, since the
CDMA frequency is the same.
Centralized Methods
The band used in CDMA is 824 MHz to 894 MHz (50 MHz + 20 MHz
separation).
Frequency channel is divided into code channels.
1.25 MHz of FDMA channel is divided into 64 code channels.
Processing Gain
CDMA is a spread spectrum technique. Each data bit is spread by a code
sequence. This means, energy per bit is also increased. This means that we get
a gain of this.
P (gain) = 10log (W/R)
W is Spread Rate
R is Data Rate
04/10/2023, 11:21 CDMA - Quick Guide
For CDMA P (gain) = 10 log (1228800/9600) = 21dB
This is a gain factor and the actual data propagation rate. On an average, a
typical transmission condition requires a signal to the noise ratio of 7 dB for the
adequate quality of voice.
Translated into a ratio, signal must be five times stronger than noise.
Actual processing gain = P (gain) - SNR
= 21 – 7 = 14dB
CDMA uses variable rate coder
The Voice Activity Factor of 0.4 is considered = -4dB.
Hence, CDMA has 100% frequency reuse. Use of same frequency in

surrounding cells causes some additional interference.
In CDMA frequency, reuse efficiency is 0.67 (70% eff.) = -1.73dB
Advantages of CDMA
CDMA has a soft capacity. The greater the number of codes, the more the
number of users. It has the following advantages −
CDMA requires a tight power control, as it suffers from near-far effect.

In other words, a user near the base station transmitting with the same
power will drown the signal latter. All signals must have more or less
equal power at the receiver
Rake receivers can be used to improve signal reception. Delayed

versions of time (a chip or later) of the signal (multipath signals) can be
collected and used to make decisions at the bit level.
Flexible transfer may be used. Mobile base stations can switch without
changing operator. Two base stations receive mobile signal and the
mobile receives signals from the two base stations.
Transmission Burst − reduces interference.
Disadvantages of CDMA
04/10/2023, 11:21 CDMA - Quick Guide
The disadvantages of using CDMA are as follows −
The code length must be carefully selected. A large code length can
induce delay or may cause interference.
Time synchronization is required.
Gradual transfer increases the use of radio resources and may reduce
capacity.
As the sum of the power received and transmitted from a base station
needs constant tight power control. This can result in several handovers.
CDMA - Network
CDMA Network is the system meant to regulate CDMA technology. It includes
all aspects and functionality starting from the base station, transmitting
antenna, receiving antenna, to mobile switching centers.
CDMA Network Overview

A base station is an essential element of the CDMA network. A base station
covers a small geographical area called a cell. A cell may be omnidirectional or
sectoral. Each base station has a transmitting antenna and two receiving
antennas for each cell. Two receiving antennas are used per cell for the
purpose of spatial diversity. In many applications, it is a BSC (Base Station
Controller), which controls several base stations.
As the rate of the mobile phone data is either 13kbps or 8kbps, which is
nonISDN, but the switches which are the mobile switching center (MSC) are
generally switched to 64 kbps. Therefore, before it is switched, it is necessary
04/10/2023, 11:21 CDMA - Quick Guide
to convert this mobile data rates to 64 kbps. This is accomplished by a

member, which is the transcoder. The transcoder may be a separate element
or it can be collocated in each base station or MSC.
All base stations are connected to the MSC, which is the mobile switching
center. MSC is the entity that manages the establishment, connection,
maintenance, and disposal of calls within the network and also with the outside
world.
MSC also has a database called HLR/AC, which is a home location

register/authentication center. HLR is the database, which maintains the
database of all network subscribers. AC Authentication Centre is the part of the
security of the HLR, which some algorithms to examine mobile phones.
The MSC is connected to the outside world, i.e. the fixed line network. MSC can
also be connected to several other MSCs.
CDMA Identities
Network Identities −
SID (System Identity)

NID (Network Identity)
Mobile Station Identities −
ESN (Electronic Serial Number)

Permuted ESN
IMSI (International Mobile Station Identity)
IMSI_S
IMSI_11_12
Station Class Mark
System and Network Identity

A base station is a member of a cellular system and a network. A network is a
subset of a system. The systems are installed with an identification called
04/10/2023, 11:21 CDMA - Quick Guide
Identification System (CIS). The networks with a system receiving is

Network identification (NID). It is a uniquely identified network pair of (SID,
NID). The mobile station has a list of one or more home (non-roaming) pairs
(SID, NID).
SID
A system identification indicator 15 bits (SID) is stored in a mobile station. It is

used to determine the host system of the mobile stations. The bit allocation of
the system identification indicator is shown below.
The distribution of international codes (INTL) (bits 14 and 13) is also shown in
the table. Bits 12-0 is assigned to each US system by the FCC for non-US
countries. The bit allocation will be made by local regulatory authorities.
NID
NID has a range of 0-65535 reserved values. Value of 65535 in a SID means,
NID pair is to indicate that the Mobile Station considers the entire SID as
home.
Systems and Networks
A mobile station has a list of one or more home (non-roaming) pairs (SID,
NID). A mobile station is roaming when the base station broadcast (SID, NID)
pair does not match with one of the non-roaming mobile stations (SID, NID)
pairs.
A mobile station is a foreign NID roamer −
if the mobile station is roaming and there are some (SID, NID) pair in
the mobile stations (SID, NID) list that corresponds to SID.
if the mobile station is roaming and there are some (SID, NID) pair in
the mobile stations (SID, NID) list for which no matching SID is
04/10/2023, 11:21 CDMA - Quick Guide
available (means a mobile station has roaming customer foreign SID).
Electronic Serial Number (ESN)
ESN is a 32-bit binary number that uniquely identifies the mobile station in a
CDMA cellular system. It should be set at the factory and cannot be easily
changed in the field. Changing the ESN will require special equipment, not
normally available to subscribers. The bit allocation of ESN is shown below −
The circuit that provides the ESN must be isolated so that no one can contact
and tamper. Attempts to change the ESN circuit should make the mobile station
inoperative. At the time of the issuance of the initial acceptance, the
manufacturer must be assigned a code Manufacturers (MFR) in the eight most
significant bits (bits 31-24 bits) 32-bit serial number. Bits 23-18 are reserved
(initially zero). And, every manufacturer only allocates 17 bits to 0. When a
manufacturer has used almost all possible combinations of serial numbers in
bits 17-0, the manufacturer may submit a notification to the FCC. The FCC will
assign the next sequential binary number in the reserve block (bits 23
through).
Permuted ESN
CDMA is a spread spectrum technique where multiple users to access the

system at the same example in a cell, and of course on the same frequency.
Therefore, it discriminates the users on the reverse link (i.e. information from
MS to the base station). It spreads information using codes that are unique to
the mobile station in all the CDMA cellular systems. This code has an element
that is the ESN, but it doesn’t use the ESN in the same format instead, it uses
an ESN swapped.
If there are two mobiles in a cell of the same brand and have consecutive serial
numbers and for the receiver of the base station, it becomes difficult to connect
them. Therefore, to avoid a strong correlation between the long codes
corresponding to successive ESN, we use permuted ESNs.
International Mobile Station Identity (IMSI)
04/10/2023, 11:21 CDMA - Quick Guide
Mobile stations are identified by the identity of the international mobile station
Identity (IMSI). The IMSI consists of up to 10 to 15 numeric digits. The first
three digits of the IMSI are the country code of the mobile (MCC), the
remaining digits are the National NMSI mobile station identity. The NMSI
consists of the mobile network code (MNC) and the mobile station identification
number (SIDS).
MCC MSN MSIN
NMSI
IMSI ≤15 digits
MCC: Mobile Country Code

MNC: Mobile Network Code
MSIN: Mobile Station Identification
NMSI: National Mobile Station Identity
An IMSI that is 15 digits in length is called a class 0 IMSI (NMSI is the 12 digits
in length). IMSI, which is less than 15 digits in length, is called a class 1 IMSI
(NMSI the length is less than 12 counts). For CDMA operation, the same IMSI
may be registered in multiple mobile stations. Individual systems may or may
not allow these capabilities. The management of these functions is a function of
the base station and the system operator.
CDMA - Techniques
Rake Receiver
Due to the reflection on the challenges of a broadband, radio channel can
consists of many copies (multipath), signals originally transmitted with
different amplitude, phase, and delay. If the signal components arrive over a
chip period of each other, a rake receiver may be used to adjust and combine.
The Rake receiver uses a principle of diversity through multiple paths. The
figure given below shows the Rake receiver scheme.
04/10/2023, 11:21 CDMA - Quick Guide
The Rake receiver processes several multipath signals components. The

correlator outputs are combined to achieve better reliability and communication
performance. Bit decision on the basis of a single correlation can produce a
large bit error rate as multipath component processed by the fact that the
correlator can be damaged by discoloration. If the output of a correlator is
corrupted by fading, the other cannot be, and the corrupt signal can be
reduced by the weighting process.
Walsh Code
Walsh Codes are most commonly used in the orthogonal codes of CDMA
applications. These codes correspond to lines of a special square matrix called
the Hadamard matrix. For a set of Walsh codes of length N, it consists of n
lines to form a square matrix of n × n Walsh code.
The IS-95 system uses 64 Walsh function matrix 64. The first line of this matrix
contains a string of all zeros with each of the following lines containing different
combinations of bit 0 and 1. Each line is orthogonal and equal representation
for binary bits. When implemented with the CDMA system, each mobile user
uses one of the 64 sequences of rows in the matrix as a spreading code. And, it
provides zero cross-correlation among all the other users. This matrix is
defined recursively as follows −
04/10/2023, 11:21 CDMA - Quick Guide
Where n is a power of 2 and indicates the different dimensions of the matrix W.

Further, n represents the logic NOT operation on all bits in this matrix. The
three matrices W2, W4, and W8, respectively show the Walsh function for the
dimension 2, 4, and 8.
Each line of the 64 Walsh matrix 64 corresponds to a channel number. The

channel number 0 is mapped to the first row of the Walsh matrix, which is the
code of all zeros. This channel is also known as the pilot channel and is used to
form and to estimate the impulse response of a mobile radio channel.
To calculate the cross-correlation between the sequences, we will need to

convert the bits into the matrix to form the antithesis of ± 1 values. However,
all users on the same CDMA channel can be synchronized with an accuracy of
one chip interval using a common long PN sequence. It also functions as a data
scrambler.
Walsh Code is a group of spreading codes having good autocorrelation

properties and poor cross correlation properties. Walsh codes are the
backbone of CDMA systems and are used to develop the individual
channels in CDMA.
For IS-95, there are 64 codes available.
Code `0’ is used as the pilot and code `32’ is used for
synchronization.
Codes 1 through 7 are used for control channels, and the

remaining codes are available for traffic channels. Codes 2 to 7
are also available for traffic channels if they are not needed.
04/10/2023, 11:21 CDMA - Quick Guide
For cdma2000, multitude of Walsh codes exist, which vary in length to

accommodate the different data rates and Spreading Factors of the
different Radio Configurations.
One of the 64 orthogonal bit pattern at a rate of 1.2288 Mcps.
Walsh codes are used to identify the data for each individual
transmission. In the forward link, they define forward code channels
within a CDMA frequency.
In the reverse link, all 64 codes are used by each reverse channel to
carry information.
Take a look at the following illustration. It shows how multiplexing is carried out
using Walsh Code.
CDMA - Spread Spectrum

All technical modulation and demodulation strive for greater power and/or
efficiency of bandwidth in a white Gaussian additive stationary noise channel.
Since bandwidth is a limited resource, one of the primary design goals of all the
modulation schemes is to minimize the bandwidth required for transmission.
On the other hand, spread spectrum techniques use a transmission bandwidth
that is order of the magnitude greater than the bandwidth required the
minimum signal.
The advantage of spread spectrum technique is that — many users can

simultaneously use the same bandwidth without interfering with each other.
Therefore, spread spectrum is not economic when the number of users is less.
04/10/2023, 11:21 CDMA - Quick Guide
Spread spectrum is a form of wireless communications in which the

frequency of the transmitted signal is deliberately varied resulting higher
bandwidth.
Spread-spectrum is apparent in the Shannon and Hartley channel-
capacity theorem −
C = B × log2 (1 + S/N)
In the given equation, `C’ is the channel capacity in bits per second
(bps), which is the maximum data rate for a theoretical bit-error rate
(BER). ‘B’ is the required channel bandwidth in Hz, and S/N is the
signal-to-noise power ratio.
Spread spectrum uses wideband, noise-like signals that are hard to
detect, intercept, or demodulate. Additionally, spread-spectrum signals
are harder to jam (interfere with) than narrow band signals.
Since spread-spectrum signals are so wide, they transmit at a much

lower spectral power density, measured in watts per hertz, than narrow
band transmitters. Spread-spectrum and narrowband signals can occupy
the same band, with little or no interference. This capability is the main
attraction for all the interest in spread spectrum today.
Points to Remember −
The transmitted signal bandwidth is greater than the minimal

information bandwidth, which is needed to transmit the signal
successfully.
Some function other than the information itself is normally employed to
determine the resultant transmitted bandwidth.
Following are the two types of spread spectrum techniques −
Direct Sequence and

Frequency Hopping.
Direct Sequence is adopted by CDMA.
Direct Sequence (DS)
04/10/2023, 11:21 CDMA - Quick Guide
Direct Sequence Code Division Multiple Access (DS-CDMA) is a technique to

multiplex users by different codes. In this technique, the same bandwidth is
used by different users. Each user is assigned with one its own spreading code.
These sets of codes are divided into two classes −
Orthogonal Codes and

Non-Orthogonal Codes
Walsh sequences come into the first category which is Orthogonal Codes
whereas other sequences i.e. PN, Gold, and Kasami are shift register
sequences.
Orthogonal codes are assigned to the users, the output of the correlator in the
receiver will be zero except the desired sequence. In synchronous direct
sequence, the receiver receives the same code sequence which was
transmitted so that there is no time shift between the users.
Demodulating DS Signals - 1
In order to demodulate DS signals, you need to know the code that was used
at the time of transmission. In this example, by multiplying the code used in
the transmission to the reception signal, we can get the transmitted signal.
In this example, multiple codes were used at the time of transmission

(10,110,100) to the received signal. Here, we have calculated by using the law
04/10/2023, 11:21 CDMA - Quick Guide
of two additives (Modulo 2 Addition). It is further demodulated by multiplying

the code that was used at the time of this transmission, called the reverse
diffusion (de-spreading). In the diagram given below, it can be seen that
during the transmission of the data to the narrow band (Narrow Band)
spectrum, the spectrum of the signal is dispread.
Demodulating DS Signals − 2
On the other hand, if you do not know the code that was used at the time of
transmission, you will not be able to demodulate. Here, you are trying to
demodulation in the code of different (10101010) and the time of transmission,
but it has failed.
Even looking at the spectrum, it is spreading during the time of transmission.

When it is passed through a band-pass filter (Band Path Filter), only this small
signal remains and these are not demodulated.
04/10/2023, 11:21 CDMA - Quick Guide
Features of Spread Spectrum

As shown in the following figure, the power density of Spread Spectrum signals
could be lower than the noise density. This is a wonderful feature that can keep
the signals protected and maintain privacy.
By spreading the spectrum of the transmitted signal, one can reduce its power
density such that it becomes less than the power density of the noise. In this
way, it is possible to hide the signal in the noise. It can be demodulated if you
know the code that was used to send the signal. In case the code is not known,
then the received signal will remain hidden in the noise even after the
demodulation.
04/10/2023, 11:21 CDMA - Quick Guide
DS-CDMA
DS code is used in CDMA. So far, it has been explained basic part of the spread
spectrum communication. From here, we will explain how Direct Sequence
Code Division Multiple Access (DS-CDMA) works.
The signal which is spread spectrum, can be demodulated only by a code used
for transmission. By using this, the transmission signal of each user can be
identified by the separate code when it receives the signal. In the given
example, the spread signal of the user A at the code A, and diffused signal of
user B at code B. Each of the signal when it receives are mixed. However, by
the inverse diffuser (Despreadder), it identifies the signal of each user.
DS-CDMA System - Forward Link
DS-CDMA System - Reverse Link
04/10/2023, 11:21 CDMA - Quick Guide
Spreading Code
Cross-Correlation
Correlation is a method of measurement of how precisely a given signal

matches with a desired code. In CDMA technology, each user is assigned with a
different code, the code which is being assigned or chosen by the user is very
important to modulate the signal because it is related to the performance of
the CDMA system.
One will get best performance when there will be clear separation between the
signal of desired users and signals of the other users. This separation is made
by correlating the desired signal code which was locally generated and other
received signals. If the signal matches with the code of the user, then the
correlation function will be high and the system can extract that signal. If the
user's desired code has nothing in common with the signal, the correlation
should be as close to zero as possible (thus eliminating the signal); also known
as cross correlation. So, there is a self-correlation (Self-Correlation) and
cross-correlation (Cross-Correlation).
Properties of self-correlation and code are shown in the diagram given below
where correlation between spreading code ‘A’ and spreading code ‘B’ is shown.
In this example, the calculated correlation of spreading code ‘A
(1010110001101001) and spreading code ‘B’ (1010100111001001) is given,
while performing calculations in below example, the result has come to 6/16.
04/10/2023, 11:21 CDMA - Quick Guide
Preferable Codes
Preferable code is used in CDMA. There are different codes that can be used
depending on the type of a system of CDMA. There are two types of system −
Synchronous (Synchronous) System and

Asynchronous (Asynchronous) System.
In a synchronous system, orthogonal codes (Orthogonal Code) can be used. In

asynchronous system for this, such as pseudo-random code (Pseudo-random
Noise) or Gold code is used.
In order to minimize mutual interference in DS-CDMA, the spreading codes

with less cross-correlation should be chosen.
Synchronous DS-CDMA
Orthogonal Codes are appropriate. (Walsh code etc.)
Asynchronous DS-CDMA
Pseudo-random Noise (PN) codes/Maximum sequence

Gold Codes
04/10/2023, 11:21 CDMA - Quick Guide
Synchronous DS-CDMA
Synchronous CDMA Systems are realized in Point to Multi-point Systems. For

example, Forward Link (Base Station to Mobile Station) in Mobile Phone.
Synchronization system is used in one-to-many (Point to Multipoint) systems.

For example, at a given time, in a mobile communication system, a single base
station (BTS) can communicate with multiple cell phones (forward
link/downlink).
In this system, a transmission signal for all the users can communicate in
synchronization. Means, "Synchronization" on this point is a sense that can be
sent to align the top of each user signal. In this system, it is possible to use
orthogonal codes and it is also possible to reduce mutual interference. And
orthogonal codes, it is the sign, such as cross-correlation i.e. 0.
Asynchronous DS-CDMA
In asynchronous CDMA system, orthogonal codes have bad cross-correlation.
Unlike the signal from the base station, the signal from the mobile station to
the base station, becomes the asynchronous system.
In an asynchronous system, somewhat mutual interference increases, but it

uses the other codes such as PN code or Gold code.
04/10/2023, 11:21 CDMA - Quick Guide
Advantages of Spread Spectrum

Since the signal is spread over a wide frequency band, the power spectral
density becomes very low, so other communication systems do not suffer from
this kind of communication. However, the Gaussian noise increases. Given
below is a list of a few major advantages of Spread Spectrum −
Multipath can be agreed with, as a large number of codes can be

generated, allowing a large number of users.
In spread spectrum, there is no limit of users whereas there is
limitations of users in FDMA technology.
Security − without knowing the spreading code, it is hardly possible to
recover the transmitted data.
Descending rejection − as large bandwidth is used the system; it is less
susceptible to deformation.
PN Sequence
The DS-CDMA system uses two types of spreading sequences, i.e., PN
sequences and orthogonal codes. As mentioned above, the PN sequenc is
generated by the pseudo-random noise generator. It is simply a binary linear
feedback shift register, consisting of XOR gates and a shift register. This PN
generator has the ability to create a sequence identical for both the transmitter
and the receiver, and retaining the desirable properties of the noise
randomness bit sequence.
A PN sequence has many features such as having an almost equal number of

zeros and ones, very low correlation between shifted versions of the sequence,
and very low cross-correlation with other signals such as interference and
noise. However, it is able to correlate well with itself and its inverse. Another
important aspect is the autocorrelation of the sequence as it determines the
ability to synchronize and lock the spreading code for the received signal. This
fight effectively effects the multiple interference and improves the SNR. M-
sequences, Gold codes, and Kasami sequences are the examples of this class of
sequences.
04/10/2023, 11:21 CDMA - Quick Guide
A Pseudo-random Noise (PN) sequence is a sequence of binary numbers,

e.g. ±1, which appears to be random; but it is in fact, perfectly
deterministic.
PN sequences are used for two types of PN spread spectrum techniques
−
Direct Signal Spread Spectrum (DS-SS) and

Frequency Hop spread Spectrum (FH-SS).
If ‘u’ uses PSK for modulating the PN sequence, it results in DS-SS.

If ‘u’ uses FSK for modulating the PN sequence, it results in FH-SS.
Frequency Hopping Technology

Frequency hopping is a spread spectrum in which the propagation takes place
by hopping in frequency over a wide band. The precise order in which the
break occurs is determined by a hopping table generated by using a pseudo-
random code sequence.
Hopping rate is a function of the speed information. The order of frequencies is

selected by the receiver and is dictated by the pseudo-random noise sequence.
Although the transmission of a frequency hopping signal spectrum is quite
different from that of a direct sequence signal, it suffices to note that the data
is distributed over a signal band is larger than necessary to carry. In both the
cases, the resulting signal will appear as noise and the receiver uses a similar
technique, which is used in the transmission to recover the original signal.
CDMA - Fading
In wireless communications, fading is the deviation of the signal attenuation
affecting a certain propagation media. Discoloration may vary with time, the
geographical position or frequency of the radio, which is often modeled as a
random process. A fading channel is a communication channel experiencing
fading.
Multipath Fading
04/10/2023, 11:21 CDMA - Quick Guide
In wireless systems, fading can be either due to multipath, called as multipath

fading or due to shadowing from obstacles affecting the wave propagation,
known as shadow fading. Here in this chapter, we will discuss how multipath
fading affects the reception of signals in CDMA.
Fading in CDMA System

CDMA systems use a signal fast chip rate for spreading the spectrum. It has a
high time resolution, due to which it receives a different signal from each path
separately. The RAKE receiver prevents signal degradation by summing all the
signals.
04/10/2023, 11:21 CDMA - Quick Guide
Because CDMA has high time-resolution, different paths delay the CDMA
signals, which can be discriminated. Therefore, energy from all paths can be
summed by adjusting their phases and path delays. This is a principle of RAKE
receiver. By using a RAKE receiver, it is possible to improve the loss of the
received signal due to fading. It can ensure a stable communication
environment.
In CDMA systems, multi-path propagation improves the signal quality by using

RAKE receiver.
CDMA - Near-Far Problem

Near-far problem is one of the major problems that hurts mobile
communications badly. In a CDMA system, mutual interference will determine
the majority of SN ratio of each user.
How Near-Far Problem Affects Communication?

The following illustration shows how near-far problem affects communication.
04/10/2023, 11:21 CDMA - Quick Guide
As shown in the illustration, user A is far away from the receiver and user B is
close to the receiver, there will be big difference between desired signal power
and interfered signal power. Desired signal power will be much higher than the
interfered signal power and hence SN ratio of user A will be smaller and
communication quality of user A will be severely degraded.
CDMA - Power Control

In CDMA, since all the mobiles transmit at the same frequency, the internal
interference of the network plays a critical role in determining network
capacity. Further, each mobile transmitter power must be controlled to limit the
interference.
Power control is essentially needed to solve the near-far problem. The main
idea to reduce the near-far problem, is to achieve the same power level
received by all mobiles to the base station. Each received power must be at
least level, so that it allows the link to meet the requirements of the system
such that Eb/N0. To receive the same power level at the base station, the
mobiles those are closer to the base station should transmit less power than
the mobiles which are far away from the mobile base station.
In the figure given below, there are two mobile cells A and B. A is closer to the
base station and B is far from the base station. Pr is the minimum signal level
for the performance of the required system. Therefore, the mobile B should
transmit more power to achieve the same Pr to the base station (PB>PA). If
there is no power control, in other words, the transmission power are the same
04/10/2023, 11:21 CDMA - Quick Guide
from both the mobile cells, the signal received from A is much stronger than
the signals received from mobile cell B.
When all mobile stations transmit the signals at the same power (MS), the
received levels at the base station are different from each other, which depend
on the distances between BS and MSs.
The received level fluctuates quickly due to fading. In order to maintain the
received level at BS, a suitable power control technique must be employed in
CDMA systems.
We need to control the transmission power of each user. This control is called
the transmission power control (Control Power). There are two ways to
control the transmission power. First is the open-loop (Open Loop) control and
second is closed-loop (Closed Loop) control.
Reverse Link Power Control
04/10/2023, 11:21 CDMA - Quick Guide
In addition to the near-far effect described above, the immediate problem is to

determine the transmit power of the mobile when it first establishes a
connection. Until the mobile does not come in contact with the base station, it
has no idea of the amount of interference in the system. If it attempts to
transmit high power to ensure contact, then it can introduce too much
interference. On the other hand, if the mobile transmits less power (not to
disturb other mobile connections), the power cannot meet the Eb/N0 as
required.
As specified in the IS-95 standards, mobile acts when it wants to get into the
system, it sends a signal called access.
In CDMA, each user's transmission power is allocated by the control power to

achieve the same power (Pr) which is received by the base station/BTS with
access probe with low power. The mobile sends its first access probe, then
waits for a response from the base station. If it receives no response, then the
second access probe is sent with a higher power.
The process is repeated until the base station responds. If the signal answered
by the base station is high, then the mobile gets connected with the base
station which is closer to the mobile cell with low transmission power. Similarly,
if the signal is weak, the mobile knows the path loss is greater and transmits
high power.
The process described above is called open loop power control since it is
controlled only by the mobile itself. Open loop power control starts when the
first mobile attempts to communicate with the base station.
This power control is used to compensate for the slow variables shading
effects. However, since the rear and forward links are on different frequencies,
the estimate transmit power does not give accurate solution for the power
control because of the path loss to the front of the base station. This power
control fails or too slow for fast Rayleigh fading channels.
The power of closed loop control is used to compensate for the rapid Rayleigh
discoloration. This time, the mobile transmit power is controlled by the base
station. For this purpose, the base station continuously monitors the reverse
link signal quality. If the quality of the connection is low, it tells the mobile to
increase its power; and if the quality of the connection is very high, the mobile
base station controller reduces its power.
Forward Link Power Control

04/10/2023, 11:21 CDMA - Quick Guide
Similar, to reverse link power control, forward link power control is also
necessary to maintain the forward link quality to a specified level. This time,
the mobile monitors the forward link quality and indicates to the base station to
turn on or off. This power control has no effect on the near-far problem. All the
signals are blurred together at the same level of power when they get to the
mobile. In short, there is no near-far problem in the forward link.
Effect of Power Control

By transmission power control, the user can obtain a constant communication
environment regardless of the location. The user who is far from the base
station sends a higher transmission power than the user who is nearer to the
base station. Also by this transmission power control, you can reduce the
effects of fading. This means that the variation of the received power due to
fading can be suppressed by the transmission power control.
Power control is capable of compensating the fading fluctuation.

Received power from all MS are controlled to be equal.
Near-Far problem is mitigated by the power control.
CDMA - Frequency Allocation

The major capacity advantage of CDMA is that it reuses the same allocated
frequency in every sector of every cell. In IS-136 and analog cellular systems,
there is a seven cell repeat factor, with three sectors. This means that only one
out of every 21 channels is available to each sector. CDAM is designed to share
the same frequency in each sector of each cell. For each user that uses
cdma2000 coding rather than IS-95, the system is more efficient.
In FDMA or TDMA, radio resource is allocated not to interfere among neighbor

cells −
04/10/2023, 11:21 CDMA - Quick Guide
Neighbor cells cannot use the same (identical) frequency band (or
timeslot).
The left figure shows the simple cell allocation with seven bands of
frequency.
In actual situation, because of complicated radio propagation and irregular cell

allocation, it is not easy to allocate frequency (or timeslot) appropriately.
In a CDMA system against this, since all users share the same frequency, the
arrangement of the frequency is not an issue. This is the biggest advantage of
CDMA technology.
04/10/2023, 11:21 CDMA - Quick Guide
In CDMA, identical radio resource can be used among all cells, because CDMA
channels use same frequency simultaneously.
Frequency allocation in CDMA is not necessary.

In this sense, CDMA cellular system is easy to design.
CDMA - Handoff
Whenever a cellular subscriber passes through one base station to another, the
network automatically switches to the other respective base station and
maintains the coverage responsibility. This behavior called "hand-off" (Handoff)
or "hand-over" (Handover).
Whereas in FDMA and TDMA systems, it uses a different frequency to

communicate with the base station of that area. It means, there will be a
frequency switch from one frequency to another, and during the switching,
there will be slightly communication cut, which is called as "hard handoff"
(Hard Handoff) or "hard handover" (Hard Handover).
Hard Handoff
In FDMA or TDMA cellular system, a new communication can be established
after breaking the current communication at the moment of handoff.
04/10/2023, 11:21 CDMA - Quick Guide
Communication between MS and BS breaks at the time of switching the

frequency or timeslot.
Soft Handoff
Cellular systems track mobile stations in order to maintain their communication
links. When mobile station goes to a neighbor cell, the communication link
switches from the current cell to the neighbor cell.
When a mobile enters in a new area (from the base station to another base
station), the mobile is the second pilot of sufficient power by sending the
message to the strength of the driver to the first base station. The base station
notifies the MTSO and then the MTSO requests new Walsh code assignment
of the second base station.
04/10/2023, 11:21 CDMA - Quick Guide
The first base station controls with new progressive transfer Walsh
assignment MTSO then sends land link to the second base station.
Mobile is powered by two base stations and MTSO selects the best
quality status for every 20 ms.
The power goes low at the mobile station by the first BS and mobile
sends a pilot strength message then the first BS transmission stops and
releases the channel. And, traffic channel continues on the second base
station.
In CDMA cellular system, communication does not break even at the
moment doing handoff, because switching frequency or timeslot is not
required.
Note − A Walsh sequence is a part of Orthogonal Codes, whereas other

sequences such as PN, Gold, and Kasami are shift register sequences. In case
orthogonal codes are assigned to the users, the output of the correlator in the
receiver will be zero except the desired sequence, whereas synchronous direct
sequence receiver receives the same code sequence which was transmitted, so
there is no time shift between the users.
CDMA - Interferences
A CDMA signal experiences high interference signals other than the CDMA
users. This takes two forms of interference — interference from other users in
the same minicell and interference from the adjacent cells. The total
interference also includes the background noise and other spurious signals.
CDMA is based on the use of a spread spectrum form of modulation to encode

a signal for its transmission and retrieval.
Noise Sources
In the spread spectrum technology, the radio signals are distributed on a single
1.23 MHz wide frequency band. Each subscriber has assigned PN codes. Signals
corresponding to the PN codes are decoded and processed. Signals that do not
contain the code matches are treated as noise and ignored.
Signal Processing: Receive
04/10/2023, 11:21 CDMA - Quick Guide
CDMA starts with an encoded narrowband signal; this spreads with the use of
the PN codes to a bandwidth of 1.23 MHz.
When the signal is received, it is filtered and processed to recover the desired
signal. A correlator eliminates sources of interference because they are
uncorrelated with the desired signal treatment. Using this method, the number
of CDMA calls can occupy the same frequency spectrum simultaneously.
Frame Error Rate
The number of transmission errors, measured in terms of frame error rate

(FER). It increases with the number of calls. To overcome this problem, the
minicell and mobile site can increase the power until either the mobile or the
minicell site can power up more further to reduce FER to an acceptable
amount. This event provides a soft limit calls from a particular minicell and
depends on −
The noise floor naturally occurring and man-made interference.

Interference from calls on this minicell.
Interference from calls on other cells.
Power per Walsh Code
The power control bit is used during call processing to maintain the relative
power of each individual active traffic channel and power up or down to
maintain acceptable FER measurements by the mobile on the channel. This
power is expressed in terms of digital gain units.
The following actions can be seen in the transmit path −
The low bit rate digital voice packet from PSU2 (packet switch unit 2 in
the 5ESS switch) is spread by a Walsh code in the minicell.
The RF transmit carrier frequency is modulated by the spread signal.
The direct sequence spread spectrum signal is transmitted.
The following actions can be seen in the receive path −
The direct sequence spread spectrum signal is received.

04/10/2023, 11:21 CDMA - Quick Guide
The signal is demodulated by using the RF receive carrier frequency.

The signal dispreads by using the same Walsh code.
A bit detector restores the decoded signal to a reasonable
representation of original speech pattern.
Kickstart Your Career

Get certified by completing the course
Get Started
Print Page Previous Next
Advertisements
Tutorials Point is a leading Ed Tech

company striving to provide the best
learning material on technical and non-
technical subjects.
04/10/2023, 11:21 CDMA - Quick Guide
About us Terms Our Products

Company Terms of use Free Library
Our Team Privacy Policy Articles
Careers Refund Policy Coding Ground
Jobs Cookies Policy Certifications
Become a Teacher FAQ's Courses
Affiliates eBooks
Contact Us Corporate Training
Free Web Graphics
Contact Us
Tutorials Point India Private Limited,
Incor9 Building, Kavuri Hills, Madhapur,
Hyderabad, Telangana - 500081, INDIA
© Copyright 2023. All Rights Reserved.

CDMA - Quick Guide

Uploaded by

Copyright:

Available Formats

CDMA - Quick Guide

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CDMA - Quick Guide

Uploaded by

Copyright:

Available Formats

04/10/2023, 11:21 CDMA - Quick Guide

Menu Search tutorials, courses and ebooks...

Let’s take a simple analogy to understand the concept of CDMA. Assume we

Salient Features of CDMA

In CDMA, every channel uses the full available spectrum.

Third Generation Standards

1x — uses a spreading rate of 1.2288 Mcps.

3x — uses a spreading rate of 3 × 1.2288 Mcps or 3.6864 Mcps.

WCDMA/FDD-DS — Wideband CDMA (WCDMA) Frequency Division

CDMA Development Group (CDG)

CDG is comprised of service providers, infrastructure manufacturers, device

Pilot Channel − Pilot channel is a reference channel. It uses the mobile

Sync Channel − Synchronization channel carries a single, repeating

Paging Channel − Paging Channel’s main objective is to send out

Forward Traffic Channel − Forward Traffic Channels are code

Access Channel − Access channel is used by mobile stations to

CDMA - Multiple Access Methods

Frequency Division Duplex

Uplink − 1920 MHz to 1980 MHz

Bandwidth − Each carrier is located on the center of a 5 MHz wide

Nominal value of 5 MHz that can be adjusted.

200 kHz (center frequency must be a multiple of 200 kHz).

Tx-Rx Frequency Separation

The carrier frequency is designated by the UTRA Absolute Radio Frequency

Time Division Duplex

Duplex Methods of Radio Links

Example of TDD System

communicating parties cannot mean that the transmissions are intermittent.

In some TDD systems, alternative time intervals are of same duration or

Timing is often synchronized to GPS atomic clock standards specific derivative.

Frequency Division Duplex

Example of FDD System

In a cell phone with a transmitter and receiver, operating simultaneously in

FDD is widely used in different cellular telephone systems. In some systems,

Multiple Access Methods

The mobile communication, sharing wireless resources on all users, must be

An FDMA system can be easily implemented. A system can be

It does not differ significantly from analog systems; improving the

The maximum flow rate per channel is fixed and small.

FDMA and TDMA

High data rates of broadband systems require complex equalization.

Call time is needed in each slot to accommodate time to inaccuracies

Techniques generally used are direct sequence spread spectrum modulation

How Does CDMA Work?

Frequency Reuse Efficiency

P (gain) = 10log (W/R)

For CDMA P (gain) = 10 log (1228800/9600) = 21dB

Actual processing gain = P (gain) - SNR

CDMA uses variable rate coder

The Voice Activity Factor of 0.4 is considered = -4dB.

Hence, CDMA has 100% frequency reuse. Use of same frequency in

In CDMA frequency, reuse efficiency is 0.67 (70% eff.) = -1.73dB

CDMA requires a tight power control, as it suffers from near-far effect.

Rake receivers can be used to improve signal reception. Delayed

Transmission Burst − reduces interference.

The disadvantages of using CDMA are as follows −

CDMA Network Overview

to convert this mobile data rates to 64 kbps. This is accomplished by a

MSC also has a database called HLR/AC, which is a home location