FT-2000 Menu Mode
FT-2000 Menu Mode
FT-2000 Menu Mode
The Menu system of the FT-2000 provides extensive customization capability, so you can set up your transceiver just the
way you want to operate it. The Menu items are grouped by general utilization category, and are numbered from “001
001 AGc
DLY” to “149
FST DLY 149 tGEn EMRGNCY
EMRGNCY.”
Menu mode.
The Main (VFO-A) frequency display will show the
Menu Number and Menu Group name, while the Sub
(VFO-B) frequency display will show the Menu item;
the Multi-Display window shows the current setting of
the currently-selected Menu item.
2. Rotate the Main Tuning Dial knob to select the Menu
item you wish to work on. [MENU] Button
3. Rotate the [SUB VFO-B] knob to change the current Main Tuning Dial Knob [SUB VFO-B] Knob
Audio Output
of this transceiver’s capabilities, but at
NORMAL
this time is not supported.
085 J3E TX BPF
Function: Selects the audio passband of the DSP modula-
Input Signal
tor on the SSB mode.
Available Values: 1-30 / 1-29 / 2-28 / 3-27 / 4-26 / 3000
091 rout HEADPHN
1-30: 50-3000(Hz)
Function: Selects one of three audio mixing modes when
1-29: 100-2900(Hz)
2-28: 200-2800(Hz) using headphones during Dual Receive operation.
3-27: 300-2700(Hz) Available Values: SEP / Con1 / Con2
4-26: 400-2600(Hz) Default Setting: SEP
3000: 3000WB SEP (SEPARATE): Audio from the Main (VFO-A)
Default Setting: 3-27 (300-2700 Hz) receiver is heard only in the left
NOTE: ear, and Sub (VFO-B) receiver
The apparent power output, when using the widest band- audio solely in the right ear.
widths, may seem lower. This is normal, and it occurs be- Con1 (COMBINE 1): Audio from both Main (VFO-
cause the available transmitter power is distributed over a A) and Sub (VFO-B) receivers
wider bandwidth. The greatest compression of power out- can be heard in both ears, but
put, conversely, occurs when using the “4-26” setting (400- Sub (VFO-B) audio is attenu-
2600 Hz), and this setting is highly recommended for con- ated in the left ear and Main
test or DX pile-up work. (VFO-A) audio is attenuated in
the right ear.
086 J3E LSB CAR Con2 (COMBINE 2): Audio from both Main (VFO-
Function: Adjusts the receiver carrier point for the Main
A) and Sub (VFO-B) receivers
band’s (VFO-A) LSB mode.
is combined and heard equally
Available Values: –200 Hz ~ +200 Hz (10 Hz/steps)
in both ears.
Default Setting: 0 Hz
087 J3E USB CAR
Function: Adjusts the receiver carrier point for Main
band’s (VFO-A) USB mode.
Available Values: –200 Hz ~ +200 Hz (10 Hz/step)
Default Setting: 0 Hz
088 J3E SLSB CR
Function: Adjusts the receiver carrier point for the Sub
band’s (VFO-B) LSB mode.
Available Values: –200 Hz ~ +200 Hz (10 Hz/step)
Default Setting: 0 Hz
089 J3E SUSB CR
Function: Adjusts the receiver carrier point for Sub band’s
(VFO-B) USB mode.
Available Values: –200 Hz ~ +200 Hz (10 Hz/step)
Default Setting: 0 Hz
“+” Gain
099 rdSP PKT SLP
“-- ” Gain
Function: Selects the shape factor of the DSP filter for
the PKT mode.
Available Values: StP(STEEP) / nEd(MEDIUM) /
GEnt(GENTLE)
Default Setting: nEd (MEDIUM)
100 rdSP PKT NAR
IF Function: Selects the passband of the DSP filter for the
BANDWIDTH
PKT “Narrow” mode.
CONTOUR “GAIN” AND “Q” Available Values: 25 / 50 / 100 / 200 / 300 / 400 Hz
Default Setting: 300 Hz
094 rdSP NOTCH W 101 rdSP RTY SHP
Function: Selects the bandwidth of the DSP NOTCH fil- Function: Selects the passband characteristics of the DSP
ter filter for the RTTY mode.
Available Values: nArr (Narrow) / uuid (Wide) Available Values: SOFt / ShAP
Default Setting: uuid (Wide) Default Setting: ShAP
095 rdSP CW SHAP SOFt (SOFT): Primary importance is attached to the
Function: Selects the passband characteristics of the DSP phase of the filter factor.
filter for the CW mode. ShAP (SHARP): Primary importance is attached to the
Available Values: SOFt / ShAP amplitude of the filter factor.
Default Setting: ShAP 102 rdSP RTY SLP
SOFt (SOFT): Primary importance is attached to the Function: Selects the shape factor of the DSP filter for
phase of the filter factor. the RTTY mode.
ShAP (SHARP): Primary importance is attached to the Available Values: StP(STEEP) / nEd(MEDIUM) /
amplitude of the filter factor. GEnt(GENTLE)
096 rdSP CW SLP Default Setting: nEd (MEDIUM)
Function: Selects the shape factor of the DSP filter for 103 rdSP RTY NAR
the CW mode. Function: Selects the passband of the DSP filter for the
Available Values: StP(STEEP) / nEd(MEDIUM) / RTTY “Narrow” mode.
GEnt(GENTLE) Available Values: 25 / 50 / 100 / 200 / 300 / 400 Hz
Default Setting: nEd (MEDIUM) Default Setting: 300 Hz
097 rdSP CW NARR
Function: Selects the passband of the DSP filter for the
CW “Narrow” mode.
Available Values: 25 / 50 / 100 / 200 / 300 / 400 / 500 /
800 / 1200 / 1400 / 1700 / 2000 Hz
Default Setting: 500 Hz