Daewoo TV CP810 Service Manual

S/M No: CP810P-010
Service Manual
66 Cm STEREO Colour Television
CHASSIS : CP-810
MODEL : DTJ - 28A6F

DTJ - 28A7F
DTJ - 28B1F
DTJ - 28G6F
DTJ - 28G7F
DTJ - 28G8F
DAEWOO ELECTRONICS CO., LTD.

http://svc.dwe.co.kr MAR,2000
TABLE OF CONTENTS
1. Safety Instruction ........................................................................................................................ 2
2. Specifications .............................................................................................................................. 3
3. Circuit block Diagram ................................................................................................................. 5
4. Alignment Instructions ............................................................................................................... 6
5. IC Description .............................................................................................................................. 12
6. IC DC Voltage Charts .................................................................................................................. 32
7. Service Parts List/Recommendable Spare Parts List .............................................................. 35
8. Mechanical Exploded View ......................................................................................................... 45
9. Printed Circuit Board .................................................................................................................. 51
10. Schematic Diagram ..................................................................................................................... 52
1
1. Safety Instruction
WARNING : Only competent service personnel may carry out work involving the testing or repair of this equipment
X-RAY RADIATION PRECAUTION

1. Excessive high voltage can prodece potentially haz- 2. The only source of X-RAY Radiation in this TV receiver
ardous X-RAY RADIATION. To avoid such hazards, is the picture tube. For continued X-RAY RADIATION
the high voltage must not exceed the specified limit. protection, the replacement tube must be exactly the
The nominal value of the high voltage of this receiver is same type tube as specified in the parts list.
23-24kv at max beam current. The high voltage must
not, under any circumstances, exceed 30kv.
Each time a receiver require servicing, the high volt-
age should be checked. It is imprortant to use an accu-
rate and reliable high voltage meter.
SAFETY PRECAUTION
1. Potentials of high voltage are present when this 2. If any Fuse in this TV receiver is blown, replace it with
receiver is operating. Operation of the receiver outside the FUSE specified in the Replacement Parts List.
the cabinet or with the back board removed involves a 3. When replacing a high wattage resistor ( oxide metal
shock hazard from the receiver. film resistor ) in circuit board, keep the resistor 10mm
1) Servicing should not be attempted by anyone who is away from circuit board.
not thoroughly familiar with the precautions neces- 4. Keep wires away from high voltage or high tempera-
sary when working on high-voltage equipment. ture components.
2) Dischange the high potential of the picture tube 5. This receiver must operate under AC230 volts, 50Hz.
before handling the tube. The picture tube is highly NEVER connect to DC supply or any other power or
evacuated and if broken, glass fragments will be frequency.
violently expelled.
PRODUCT SAFETY NOTICE

Many electrical and mechanical parts in this have nents having such features are identified designated
special safety-related characteristics. These charac- symbol on the parts list.
teristics are often passed unnoticed by a visual Before replacing any of these components, read the
inspection and the X-RAY RADIATION protection parts list in this manual carefully. The use of substitute
afforded by them cannot necessarily be obtained by replacement parts which do not have the same safety
using replacement components rated for higher volt- characterisitics as specifide in the parts list may create
age, wattage, etc. Replacement parts which have X-RAY Radiation.
these special safety characteristics are identified in
this manual and its supplements, electrical compo-
2
2. Specifications
CRT 28" : A66EAK071X54 ( PHILIPS )
System PAL/SECAM-B/G, D/K, PAL-I/I’, SECAM-L/L’, NTSC-3.58/4.43 (Play back )
Main Voltage 230V AC, 50Hz
Power Consumption Stand-by mode : 2.0 Watts

Normal operating mode : 80 Watts
Sound output 10 + 10 Watts, 10% THD at RF 60% mod. ( 1 kHz )
Speaker 12W 8ohm x 2 EA
Antenna Impedance 75 ohm unbalanced input (Din Standard )
Tuning system Frequency Synthesize(FS) Tuning System
Tuner DT5-BF14D, EL2782-105-B
Number of Program 100 programs
Aux. Terminal 21 pin EURO-SCART jack ( AV input, TV output, RGB input )

21 pin EURO-SCART jack ( AV input, S-VHS input )
RCA type AV input jack
Headphone jack ( 3.5 mm Ol )
JACK AUDIO TERMINAL (AUDIO OUT L, R)
Remote controller R-22D05 with 2 "AAA" type batteries
Teletext TOP(5 Page memory) & FLOF(7 Page memory)

- West option : English, German/Dutch/Flemish, French, Italian, Spanish/Portuguese,
Swedish/Finnish/Danish, Hungarian, Rumanian, Turkish
- East option : Polish, Czech/Slovak, Rumanian, Servo-croat, German/Dutch/Flemish,
French, Estonian, Lettish
OSD language - West : English, German, French, Italian, Spanish, Nethelands, Swedish
- East : English, Russian, Polish, Rumanian, Czech, Hungarian
3
Specifications
PIN Signal Designation Matching Value

1 Audio Out (linked with 3) 0.5Vrms, Imp < 1 k (RF 60% MOD)
2 Audio In (linked with 6) 0.5Vrms, Imp < 10 k
3 Audio Out (linked with 1) 0.5Vrms, Imp < 1 k (RF 60% MOD)
4 Audio Earth
5 Blue Earth
6 Audio in (linked with 2) 0.5Vrms, Imp < 10 k (RF 60% MOD)
7 Blue in 0.7Vpp +
- 2dB, Imp 75
8 Slow (Function) Switching TV : 0-2V, PERI : 9.5 - 12V, Imp > 10 k
9 Green Earth
10 NC
11 Green In 0.7Vpp +
- 2dB, Imp 75
12 NC
13 Red Earth
14 Rapid(Blanking) Switching Earth
15 Red In, C In 0.7Vpp +- 2dB, Imp 75
16 Rapid(Blanking) switching Logic 0 : 0 - 0.4V, Logic 1 : 1 - 3V, Imp 75
17 Video Earth
18 Rapid Blanking Earth
19 Video Out 1Vpp +- 2dB, Imp 75
20 Video In, Y In 1Vpp +
- 2dB, Imp 75
21 Common Earth
4
3. Circuit Block Diagram
5
4. Alignment Instructions
4-1. User Remocon
R-22D05
6
Alignment Instructions
R-23D05
7
* How to Enter the “ Service Mode ” with user remocon.

1) Set the TV Pr 91
2) Sharpness “ MIN “ control.
3) Red, Green, Yellow buttons in regular sequency within 5 seconds after setting TV power off.
4) You can see the Menu of “ service mode “ on the screen.
5) The PR UP/DOWN buttons on the remote controller are used to move the selection bar up or down the Menus.
6) The VOL UP/DOWN buttons on the remote controller are used to adjust levels.
7) If you want to exit from “ Service Mode “ then power the TV off.
V. Slope 005
V. Center 995
V. Size 220
S. Curve 019
H. Center -190
H. Width 510
SVC v1 EW. Para 382
EW. Cor T 028
EW. CB 500
EW.Sym 021
R. bias 370
G. b 311
B. b 311
R. drive 330
G. d 315
B. d 330
G2 330
Sub Bri 021
DT 048
- You can see the SVC Menu by OSD in TV set.
8
4-2. AFT
Standard B/G, D/K, I and L
1) Set a Signal Generator with
- RF FREQUENCY = 38.9 MHz,
- RF OUTPUT LEVEL = 80 + - 5dBuV
- Pattern = Color Bar
- System = PAL-B/G
2) Connect the Signal Generator RF Output to TP2 (Tuner IF Output).
There must be no signal input to the tuner.
3) Set the L109 to TP1(I101, #22) with DC Voltage to 2.5V +
-0.1V
4-3. AGC
1) Set a Pattern Generator with RF LEVEL 60 +-3dBuV, RF Frequency 210. 25MHz(10CH), Pattern Color Bar.
2) Connect a OSCILLOSCOPE PROBE to P101 (TUNER AGC INPUT).
3) Set the RBOI to P101(Tuner AGC Input) with DC Voltage to 2.8V +
0.2V
-
4-4. SCREEN (G2)

1) Set a Pattern Generator with - RF Frequency : 210.25MHz (10CH)
- Pattern : RETMA
2) Select the “G2” in Menu
3) And a Horizontal Line will appear on the screen.
4) Adjust the SCREEN VOLUME on FBT barely to see the Horizontal Line.
5) Press the PR UP/DOWN keys to finish the SCREEN adjustment.
4-5. FOCUS
1) Apply a RETMA PATTERN signal.
2) Adjust the FOCUS VOLUME on FBT to obtain optimal resolution.
4-6. GEOMETRY
4-6-1 VERTICAL SLOPE ( Fixed : Adjust if need be )
1) Apply a RETMA PATTERN Signal.
2) Set the TV to Normal I mode.
3) Adjust the higher semicircle and the lower semicircle to be the same, with the V.Slope by volume
Up/Down keys.
4-6-2 VERTICAL CENTER

3) Adjust the center of the picture with the V.Center by volume Up/Down keys.
9
4-6-3 VERTICAL SIZE

* The VERTICAL CENTER adjustment has to be done in advance.
3) Adjust the VERTICAL SIZE of the picture with the select V.size by
volume UP/DOWN keys.
4-6-4 VERTICAL S-CORRECTION ( Fixed : Adjust if need be )

1) Apply a CROSSHATCH PATTERN Signal.
2) Adjust the S-CORRECTION to obtain the same distance between
horizontal lines with the S.Curve by volume UP/DOWN keys.
4-6-5 HORIZONTAL CENTER

2) Adjust picture centering with the select H.Center by volume UP/DOWN keys.
4-7. EW
4-7-1 WIDTH
2) Adjust the horizontal width to make a perfect circle with the select H.Width
by volume UP/DOWN keys.
4-7-2 PARA
2) Adjust the vertical line to straight with the select E.W Para by volume
UP/DOWN keys.
4-7-3 CORNER ( Fixed : Adjust if need be )

2) Adjust the vertical line to straight with the select EW.Cor T by volume
UP/DOWN keys.
4-7-4 SYMMETRY ( Fixed : Adjust if need be )

2) Adjust the symmetrical balance to be suitable with the select EW Sym by
volume UP/DOWN keys.
10
4-8. WHITE BALANCE

4-8-1 RGB Reference R
2
4-8-2 Beam Reference LOW ( 288, 301 : 10Cd/ m )
HIGH ( 288, 301 : 10Cd/ m2 )
4-8-3 Adjust G, B Gain with select Menu G,B of BIAS, DRIVE of select Menu so that R, G, B Bars
are on the center position of the analog meter. If R Analog meter is not on center, control
the Brightness +/- of user Remocon so as R Analog meter to be on the center position.
4-9. SUB BRIGHT

4-9-1 Pattern : Retma
4-9-2 Adjust the SUB BRIGHT with the select Sub Bri by volume UP/DOWN keys.
so that only H-Center parts of picture can be seen.
4-10. DOUBLE TEXT CENTER

4-10-1 Pattern : Pattern RED
4-10-2 Select Menu
4-10-3 Select DT in SVC menu time to see the Double Text Picture.
( Left : RF Picture, Right : Text Picture )
4-10-4 Change the Double Text control keys volume UP/DOWN keys so that the left edge of text
picture concur with the right edge of RF picture.
11
5. IC description
5-1. ST92195
(1) General Description
1.1 INTRODUCTION ports enter high impedance mode. A reset is necessary to
The ST92195 microcnontoller is developed and manufac- exit from Halt mode.
tured by STMicroelecrtonics using a proprietary n-well 1.1.3 I/O Ports
HCMOS process. Its performance derives from the use of Up to 28 I/O lines are dedicated to digital Input/Output.
a flexible 256-register programming model for ultra-fast These lines are grouped into up to five I/O Ports and can
context switching and real-time event response. The intel- be configureed on a bit basis under software control to pro-
ligent onchip peripherals offload the ST9 core from I/O vide timing, status signals, timer and output, analog inputs,
and data management processing tasks allowing critical external interrupts and serial or parallel I/O.
application tasks to get the maximum use off core 1.1.4 TV Peripherals
resources. The ST92195 MCU supports low power con- A set of on-chip peripherals form a complete system for TV
sumption and low voltage operation for power-efficient set and VCR applications:
and low-cost embedded systems. - Voltage Synthesis
1.1.1 ST9+Core - VPS/WSS Slicer
The advanced Core consists of the Central Processing - Teletext Slicer
Unit (CPU), the Register File and the Interrupt controller. - Teletext Display RAM
The general-purpose registers can be used as accumula- - OSD
tor, Index register, or address pointers. Adjacent register 1.1.5 On Screen Display
pairs make up 16-bit registers for addressing or 16-bit The human interface is provided by the On Screen Display
processing. Although the ST9 has an 8-bit ALU, the chip module, this can produce up to 26 lines of up to 80 charac-
handles 16-bit operations, including arithmetic, loads/ ters from a ROM defined 512 character set. The character
stores, and memory/register and memory/memory resolution is 10x10 dot. Four character sizes are sup-
exchanges. Two basic memory spaces are available : ported. Serial attributes allow the user to select foreground
Program Memory and the Register File, Which includes and background. Parallel attributes can be used to select
the control and status registers of the on-chip peripherals. additional foreground and background colors and underline
1.1.2 Power Saving Modes on a character by character basis.
To optimize performance versus power consumption, a 1.1.6 Teletext and Display RAM
range of operating modes can be dynamically selected. The internal 8k Teletext and Display storage RAM can be
Run Mode. This is the full speed execution mode with used to store Teletext pages as well as Display parame-
CPU and peripherals running at the maximum clock ters.
speed delivered by the phase Locked Loop(PLL) of the 1.1.7 Teletext, VPS and WSS Data Slicers
Clock Control Unit(CCU). The three on-board data slicers using a single external
Wait For Interrupt Mode. The Wait For Inter- crystal are used to extract the Teletext, VPS and WSS
rupt(WFI) instruction suspends program execution until information from the video signal. Hardware Hamming
an interrupt request is acknowledged. During WFI, the decoding is provided.
CPU clock is halted while the peripheral and interrupt 1.1.8 Voltage Synthesis Tuning Control
controller keep running at a frequency programmable via 14-bit Voltage Synthesis using the PWM (Pulse Width
the CCU. In this mode, the power consumption of the Modulation)/BRM (Bit Rate Modulation) technique can be
device can be reduced by more than 95%(LP WFI). used to genetate tuning voltages for TV set applications.
The tuning voltage is output on one of two separate output
Wait For Interrupt Mode. The Wait For Inter-
pins.
rupt(WFI) instruction, and if the Watchdog is not enable,
the CPU and its peripherals stop operation and the I/O
12
IC description
1.1.9 PWM Output - Rounding, fringe, double width, double height,

Control of TV settings is able to be made with up to eight scrolling, cursor, full background colour,
8-bit PWM outputs, with a frequency maximum of semitransparent mode and reduced intensity colour
23,437Hz at 8-bit resolution(INTCLK=12 MHz). Low reso- supported
lutions with higher frequency operation can be pro- Teletext unit, including Data slicer, Acquisition Unit and
grammed. up to 8K Bytes RAM for Data Storage
1.1.10 Serial Peripheral Interface (SPI) VPS and Wode Screen Signalling slicer
The SPI bus is used to communicate with external Integrated Sync Extractor and Sync Controller
devices via the SPI, or I 2C bus communication stan- 14-bit Voltage Synthesis for tuning reference voltage
dards. The SPI uses one or two lines for serial data and a Up to 6 external interrupts plus 1 non-maskable inter-
synchronous clock signal. rupt
1.1.11 Standard Timer (STIM) 8x8-bit programmable PWM outputs with 5V open-
The Standard Timer includes a programmable 16-bit drain or push-pull capability
down counter and an associated 8-bit prescaler with Sin- 16-bit Watchdog timer with 8-bit prescale
gle and Continuous counting modes. 16-bit standard timer with 8-bit prescaler usable as a
1.1.12 Analog/Digital Converter (ADC) Watchdog timer
In addition there is a 3 channel Analog to Digital Con- 3-channel Analog-to-Digital converter ; 6-bit guaran-
verter with integral sample and hold, fast 5.7us conver- teed
sion timer and 6-bit guaranteed resolution. Rich instruction set and 14-Addressing modes
Versatile Development Tools, including Assembler,
(2) Feature Linker, C-compiler, Archiver, Source Level Debugger
Register File based 8/16 bit Core Architecture with and Hardware Emulators with Real-Time Operating
RUN, WFI, SLOW and HALT modes System available from third parties
0OC to 70O Coperating temperature range Piggyback board available for prototyping
Up to 24 MHz Operation @5V + _10%
Minimum instruction cycle time : 375ns at 16MHz inter-
nal clock
64K Bytes ROM
256 Bytes RAM of Register file(accumulator or index
registers)
256 Bytes of on-chip static RAM
8K Bytes of TDSRAM(Teletext and Display RAM)
56-lead Shrink DIP package
28 fully programmable I/O pins
Serial Peripheral Interface
Flexible Clock controller for OSD, Data Slicer and Core
clocks running from one single low frequency external
crystal.
Enhanced Display Controller with 26 rows of 40/80
characters
- Serial and Parallel attributes
- 10x10 dot Matrix, 512 ROM characters, definable by
user
- 4/3 and 16/9 supported
13
IC description
(3) Block Diagram
14
IC description
(4) PIN DESCRIPTION

RESET Reset (input, active low). The ST9+ is initialised HYNC/CSYNC Horizontal/Composite sync. Horizontal
by the Reset signal. With the deactivation of RESET, or composite video synchronisation input to OSD. Posi-
program execution begins from the Program memory tive or negativety.
location pointed to by the vector contained in program PXFM Analog pin for the Display Pixel Frequency Multi-
memory locations 00h and 01h. plier
R/G/B Red/Green/Blue. Video color analog DAC out- AVDD Analog VDD of PLL. This pin must be tied to
puts VDD externally to the ST92195.
FB Fast Blanking. Video analog DAC output. GND Digital circuit ground.
VOD Main power supply voltage(5V 10%, digital) AGND Analog circuit ground(must be tied externally to
WSCF, WSCR Analog pins for the VPS/WPP slicer line digital GND).
PLL. CVBS1 Composite video input signal for the Teletext
MCFM Analog pin for the display pixel frequency multi- slicer and sync extraction.
plier. CVBS2 Composite video input signal for the VPS/WSS
OSCIN, OSCOUT Oscillator (input and output). slicer. Pin AC coupled.
These pins connect a parallel-resonant crystal(24MHz AVDD1, AVDD2 Analog power supplies(must be tied
maximum), or an external source to the on-chip clock externally to AVDD).
oscillator and buffer. OSCIN is the input of the oscilltor TXCF Analog pin for the VPS/WSS line PLL.
inverter and internal clock generator; OSCOUT is the CVBSO, JTDO, JTCK Test pins : leave floating.
output of the oscillator inverter. JTMS, TEST0 Test pins : must be tied to AVDD2.
VSYNC Vertical Sync. Vertical video synchronisation JTRST0 Test pin : must be tied to GND.
input to OSD. Positive or negative polarity.
Figure 2. Pin Description
15
IC description
5-2. VPS 3215C(Video Processor)

(1) Description including all substandards
The VPC 3215C is a high-quality, single-chip video front- - 4 composite, 1 S-VHS input, 1 composite output
end, which is targeted for 4:3 and 16:9, 100/120Hz TV - integrated high-quality A/D converters and associated
sets. clamp and AGC circuits
It can be conbined with other members of the DIGIT3000 - multi-standard sync processing
IC family (such as CIP 3250A, DDP 3300A, TPU 3040) - linear horizontal scaling (0.25 ... 4), as well as non-linear
and/or it can be used with 3rd-party products. horizontal scaling ‘panorama vision’
(2) Features - PAL + preprocessing (VPC 3215)
- all-digital video processing - submicron CMOS technology
- high-performance adaptive 4H comb filter Y/C separator
with adjustable vertical peaking
- multi-standard color decoder PAL/NTSC/SECAM
(3) Block Diagram
(4) Pin Descriptions

Pin 1 - Ground, Analog Front-End GND F These pins are connected to an 20.25MHz crystal oscilla-
Pin 2 - Ground, Analog Front-End GND F tor which is digitally tuned by integrated shunt capaci-
Pin 3 - CCU 5 MHz Clock Output CLK5 tances. The CLK20 and CLK5 clock signals are derived
This pin provides a clock frequency for the TV microcon- from this oscillator. An external clock can be fed into
troller, e.g. a CCU 3000 controller, It is also used by the XTAL1. In this case, clock frequency adjustment must be
DDP 3300A display controller as a standby clock. switched off.
Pin 4 - Standby Supply Voltage V STDBY Pin 7 - Ground, Analog Front-End GND F
In standby mode, only the clock oscillator is active, GNDF Pin 9 - Ground, Output Pad Circuitry GND P
should be ground reference. Please activate RESQ before Pin 10 - Interlace Output, INTLC
powering-up other supplies Pins 6 and 5-XTAL1 Crystal This pin supplies the interlace information, 0 indicates first
Input field, 1 indicates second field.
16
IC description
Pin 12 - Vertical Sync Pulse, VS Pin 52 - VGAV-Input.

This pin supplies the vertical sync signal. This pin is connected to the vertical sync signal of a VGA
Pin 13 - Front Sync Pulse, FSY signal.
This pin supplies the front sync information. Pin 53 - Front-End/Back-End Data FPDAT
Pin 14 - Main Sync/Horizontal Sync Pulse MSY/HS This pin interfaces to the DDP 3300A back-end processor.
This pin supplies the horizontal sync pulse information in The information for the deflection drives and for the white
line-locked mode. In DIGIT3000 mode, this pin is the main drive control, i.e. the beam current limiter, is transmitted by
sync input. this pin.
Pin 15 - Helper Line Output, Helper Pin 54 - Reset Input RESQ
This signal indicated a helper line in PAL + mode. A low level on this pin resets the VPC 32xx.
Pin 16 - Horizontal Clamp Pulse, HC Pin 55 - I2CBus Data SDA
This signal can be used to clamp 2
an external video signal, The pin connects to the I2Cbus data line.
that is synchronous to the input signal. The timing is pro- Pin 57 - Test Input TEST
grammable. This pin enables factory test modes. For normal operation,
Pin 17 - Active Video Output, AVO it must be connected to ground.
This pin indicates the active video output data. The signal Pin 59 - Ground, Analog Front-End GND
is clocked with the LLC1 clock. Pins 62,61,60,58 - Video 1-4
Pin 18 - Double Output Clock, LLC2 These are the analog video inputs. A CVBS or S-VHS
Pin 19 - Output Clock, LLC1 luma signal is converted using the luma (Video 1) AD con-
This is the clock reference for the luma, chroma, and sta- verter. The VIN1 input can also be switched to the chroma
tus outputs. (Video 2) ADC. The input signal must be AC-coupled.
Pin 26 - Ground, Output Pad Circuitry GND P Pin 63 - Chroma Input CIN
Pin 20 to 25,28,29 - Luma Output Y0-Y7 This pin is connected to the S-VHS chroma signal. A resis-
These output pins carry the digital luminance data. The tive divider is used to bias the input signal to the middle of
data are clocked with the LLC1 clock. the converter input range. CIN can only be connected to
Pin 30 - Main Clock Output CLK20 the chroma (Video 2) A/D converter. The signal must be
This is the 20.25MHz main clock output. AC-coupled.
Pin 31 - Supply Voltage, Digital Circuitry V SUPD Pin 64 - Analog Video Output, VOUT
Pin 34 - Ground, Digital Circuitry GND D The analog video signal that is selected for the main
Pin 35 - Ground, Output Pad Circuitry GND P (luma, CVBS) ADC is output at this pin. An emitter follower
Pin 36 - Supply Voltage, Output Pad Supply V SUPP is required at this pin.
Pin 38 to 43,46,47 - Chroma Outputs C0-C7 Pin 65 - Ground, Analog Shield Front-End GND
These outputs carry the digital CrCb chrominance data. Pin 66 - Supply Voltage, Analog Front-End V
The data are clocked with the LL1 clock. The data are Pin 67 - Signal GND for Analog Input ISGND
sampled at half the clock rate and multiplexed. The CrCb This is the high quality ground reference for the video
multiplex is reset for each TV line. input signals.
Pin 48 to 50 - Picture Bus Priority PR0-PR2 Pin 68 - Reference Voltage Top VRT
The Picture Bus Priority lines carry the digital priority Via this pin, the reference voltage for the A/D converters is
selection signals. The priority interface allows digital decoupled. The pin is connected with 10uF/47nF to the
switching of up to 8 sources to the back-end processor. Signal Ground Pin.
Switching for different sources is prioritized and can be on
a per pixel basis.
Pin 51 - Ground, Output Pad Circuitry GND P
17
IC description
5-3. CIP3250A (Component Interface Processor)

(1) Description - digital matrix RGB => YUV (Y, B-Y, R-Y)
The CIP 3250A is a new CMOS IC that contains on a sin- - luma contrast and brightness correction for signals from
gle chip the entire circuitry to interface analog YUV/RGB/ analog input
Fast Blank to a digital YUV system. The Fast Blank signal - color saturation and hue correction for signals from
is used to control a soft mixer between the digitized RGB analog input
and an external digital YUV source. The CIP supports var- - digital input for DIGIT 2000 or DIGIT 3000 formats
ious output formats such as YUV 4:1:1/4:2:2 or RGB 4:4:4. - digital interpolation to 4:4:4 format
- high quality soft mixer controlled by Fast Blank signal
Together with the DIGIT 3000 (e.g. VPC 32xxA) or DIGIT - programmable delays to match digital YUV in and analog
2000 (e.g. DTI 2250), an interface to a TV-scanrate con- RGB/YUV
version circuit and/or multi-media frame buffer can be - variable low pass filters for YUV output
obtained. - digital output in DIGIT 2000 and DIGIT 3000 formats, as
well as RGB 4:4:4
(2) Feature - I2C bus interface
- analog input for RGB or YUV and Fast Blank - clock frequency 13.5...20.25 MHz
- triple 8 bit analog to digital converters for RGB/YUV with
internal programmable clamping
- single 6 bit analog to digital converter for Fast Blank
singnal
(3) Block Diagram
18
IC description
(4) Pin Description nal(pure binary) or the digital chroma V signal (2’s compo-
Pin 1 - STANDBY Input nent). Leave vacant if not used.
Via this input pin, the standby mode of the CIP 3250A is
enabled. A high level voltage switches all outputs to Pin 29 - AVI Active Video Input
tristate mode, and power consumption is signigicantly In a DIGIT 2000 application, this input can be connected
reduced. When the IC IS returned to active mode, a reset to ground. In a DIGIT 3000 application, this input expects
is generated internally. Connect to VSS if not used. the DIGIT 3000 AVI signal. In a stand alone application,
this input expects the VSYNC vertical sync pulse. Connect
Pins 2 to 9 - B7 to B0 Blue Output ground if not used.
In a stand alone application, where the CIP 3250A serces
as an A/D-converter, these are the output for the digital Pin 30 - FSY Front Sync Input
Blue signal (pure binary) or the digital U signal (2’s com- In a DIGIT 2000 application, this input pin expects the
plement). Leave vacant if not used. DIGIT 2000 SKEW protocol. In a DIGIT 3000 application,
this input expects the DIGIT 3000 FSY protocol. In a stand
Pin 10 to 17 - GL7 to GL0 Green/Luma Output alone application, this unput expects the HSYNC horizon-
At these outputs, the digital luminance signal is received in tal sync pulse. Connect to ground if not used.
pure binary cided format for DIGIT 2000 and DIGIT 3000
2
applications. In a stand alone application, where the CIP Pin 31 to 32 - SDA and SCL of I C-Bus
2
3250A serves as an A/D-converter, these are the outputs These pins connect to the I Cbus, which takes over the
for the digital Green signal(pure binary) or the digital luma control of the CIP 3250A via the internal registers. The
signal(pure binary). Leave vacant if not used. SDA pin is the data input/output, and the SCL pin is the
2
clock input/output of I Cbus control interface. All registers
Pin 18 - PVSS Output Pin Ground are writerable(except address hex27) and readable.
This is the common ground connection of all output stages
and must be connected to ground. Pin 33 to 35 - PRIO0 to PRIO2 Priority Bus
Note : All ground pins of the chip (i.e. These pins connect to the Priority Bus of a DIGIT 3000
18,52,58,60,62,64,66 and 68) must be connected together application. The Picture Bus Priority lines carry the digital
low resistive. The layout of the PCB must take into consid- priority selection signals. The priority interface allows digi-
eration the need for a low-noise ground. tal switching of up to 8 sources to the backend processor.
Switching for different sources is prioritized and can be on
Pin 19 - PVDD Output Pin Supply + 5V/+3.3V a per pixel basis. In all other applications, they must not be
This pin supplies all output stages and must be connected connected.
to a positive supply voltage.
Note : The layout of the PCB must take into consideration Pin 36 to 43 - C0 to C7 Chroma Input
the need for a low-noise supply. A bypass capacitor has to These are the inputs for the digital chroma signal which
be connected between ground and PVDD can be received in binary offset or 2’s complement coded
format. In a DIGIT 2000(4:1:1) system, C3 to C0 take the
Pins 20 to 27 - RC7 to RC0 Red/Chroma Output halfbyte (nibble) multiplex format. C7 to C4 have to be
These are the outputs for the digital chroma signal in the connected to ground. Within the DIGIT 3000(4:2:2) sys-
DIGIT 3000 system, where U and V are multiplexed byte- tem, U and V are multiplexed bytewise. Connect to ground
wise. In a DIGIT 2000 system, RC3 to RC0 and RC7 to if not used.
RC4 carry the halfbyte(nibble) multiplex format. In a stand
alone application, where the CIP 3250A serces as an AD-
converter, these are the outputs for the digital Red sig-
19
IC description
Pin 44 to 51 - L0 to L7 Luma Input 66, and 68) must be connected together low resistive. The
These are the inputs for the digital luma signal which must layout of the PCB must take into consideration the need
be in pure binary coded format. Connect to ground if not for a low-noise ground.
used.
Pin 59 - ADREF Connect External Capacitor
Pin 52 - DVSS Digital Ground This pin should be connected to ground over a 10uF and a
This is the common ground connection of all digital stages 100nF capacitor in parallel.
and must be connected to ground.
Note : All ground pins of the chip(i.e. 18, 52, 58, 60, 62, Pin 60 - SUBSTRATE
64, 66, and 68) must be connected together low resistive. This is connected to the platform which carries the “die”
The layout of the PCB must take into consideration the and must be cvonnected to the ground.
need for a low-noise ground. Note : All ground pins of the chip(i.e.
18,52,58,60,62,64,66, and 68) must be connected
Pin 53 - DVDD Digital Supply +5V together low resistive. The layout of the PCB must take
This pin supplies all digital stages and must be connected into consideration the need for a low-noise ground.
to a positive supply voltage.
Note : The layout of the PCB must take into consideration Pin 61 - FB Analog Fast Blank Input
the need for a low-noise supply. A bypass capacitor has to This input takes the DC-coupled analog Fast Blank signal.
be connected between ground and DVDD. The amplitude is 1.0V maximum at 75 Ohms. Connect to
ground if not used.
Pin 54 - CLK Main Clock Input
This is the input for the clock signal. The frequency and Pin 62 - GNDFB Analod Ground
vary in the range from 13.5MHz to 20.25MHz. This is the ground pin for the AD converter of the Fast
Blank signal and has to be connected to ground.
Pin 55 - RESQ Input Note : All ground pins of the chip (i.e. 18,52,58,60,62,64,
A low signal at this input pin generates a reset. The low-to- 62,64,66 and 68) must be connected together low resis-
high transition of this signal should occur when the supply tive. The layout of the PCB must take into consideration
voltage is stable(power-on reset). the need for a low-noise ground.
Pin 56 - TMODE Input Pin 63 - BU Analog Blue/U Chroma Input

This pin is for test purposes only and must be connected The input pin takes the AC-coupled analog compont signal
to ground in normal operation. Blue or U Chroma. The amplitude is 1.0V maximum at 75
Ohms and a coupling capacitor of 220 nF. Internally, the
Pin 57 - AVDD Analog Supply +5V DC-offset of the input signal is adjusted via the program-
This is the supply voltage pin for the A/D converters and mable internal clamping circuit. Connect to ground if not
must be connected to a positive supply voltage. used.
Note : The layout of the PCB must take into consideration
the need for a low-noise supply. A bypass capacitor has to Pin 64 - GNDBU Analog Ground
be connected between ground and AVDD. This is the ground pin for the A/D converter of the Blue or
U Chroma signal and must be connected to ground.
Pin 58 - AVSS Analog Ground Note : All ground pins of the chip(i.e.
This is the ground pin for the A/D converters and must be 18,52,58,60,62,64,66, and 68) must be connected
connected to ground. together low resistive. The layout of the PCB must take
Note : All ground pins of the chip (i.e. 18,52,58,60,62,64, into consideration the need for a low-noise ground.
20
IC description
Pin 65 - GY Analog Green/Luma Input

This input pin takes the AC-coupled analog compinent sig-
nal Green or Luma. The amplitude is 1.0V maximum at 75
Ohms and a couplign capacitor of 220nF. Internally, the
DC-offset of the input signal is adjusted via the program-
mable internal clamping circuit. Connect to ground if not
used.
Pin 66 - GNDGY Analog Ground

This is the ground pin for the A/D converter of the Green
or Luma signal and must be connected to ground.
Note : All ground pins of the chip(i.e. 18,52,58,60,62,64,
66, and 68) must be connected together low rresistive.
The layout of the PCB must take into consideration the
need for a low-noise ground.
Pin 67 - RV Analog Red/V Chroma Input

This input pin takes the AC-coupled analog component
signal Red or V Chroma. The amplitude is 1.0V maximum
at 75ohms and a coupling capacitor of 220nF. Internally,
the DC-offset of the input signal is adjusted via the pro-
grammable internal clamping circuit. Connect to ground if
not used.
Pin 68 - GNDRY Analog Ground

This is the ground pin for the A/D converter of the Red or V
Chroma signal and must be connected to ground.
Note : All ground pins of the chip (i.e. 18,52,58,62,64,66,
and 68) must be connected together low resistive. The lay-
out of the PCB must take into consideration the need for a
low-noise ground.
21
IC description
5-4. SDA9255 (Scan Rate Converter )
(1) Features
• 100/120 Hz interlaced scan conbersion

• Data format 4:1:1
• On chip field memory
• Digital vertical zooming
• Digital vertical panning]
• Motion adaptive temporal noise reduction, field based
• Still field
• Color difference input data representation 2’s complement or unsigned
• Color difference output data representation 2’s complement or unsigned
• Sync Generation for backend IC
2
• I C - Bus control (400 kHz)
• P-MQFP-64 package
• 5V +_ 5% supply voltage

The SDA 9255 is a new component of the Siemens MEGAVISION IC set. The SDA 9255 comprises some of the func-
R
tionalities of the MEGAVISION IC’s SDA 9220 (Memory Sync Controller) and SDA 9254 (Triple TV-SAM plus Noise
R
Reduction) and can therefore be used as a low cost digital featurebox.
22
IC description
(3) Block Diagram
23
IC description
(4) Pin Description
Pin No. Name Type Description

2,8,24,26,41,55 V SS S Supply voltage ( VSS = 0V)
,57
9,25,40,56 V DD S Supply voltage ( V DD = 5V)
42,...,49 YIN0 ... 7 I/TTL Data input Y (see data format)
36,...,39 UVIN4 ... 7 I/TTL Data input UV (see data format)
30 SYNCEN I/TTL Synchronizarion enable input
31 RESET I/TTL System reset. The RESET input is low active.
In order to ensure correct operation a “Power On Reset” must be performed. The
RESET pulse must have a minimum duration of two clock periods of the system
clock (LL2CLK).
23 HIN I/TTL H-Sync input
22 VIN I/TTL V-Sync input
2
21 SDA I/O I C - Bus data line
20 SCL I I 2 C - Bus clock line
19 TESTIN I/TTL Test input, connect to V SS for normal operation
18 TESTEN I/TTL Test enable input, connect to V SS for normal operation
13,...10 UVOUT4 O/TTL Data output UV (see data format)
7,...,3,1,64,63 YOUT0 ... 7 O/TTL Data output Y (see data format)
62 HREF O/TTL Horizontal active video output
61 VOUT O/TTL V-Sync output
60 HOUT O/TTL H-Sync output
59 INTERLACED O/TTL Interlace signal for AC coupled vertical deflection
58,51 LL2CLK I/TTL System clock
50 TEST I/TTL Test input, connect to V SS for normal operation
27,28,,29,52,53 TESTO 4 ... 9 O Do not connect, Pin have to be left open
,54
14,15,16,17 TESTO 0 ... 3 O Not used output stages, do not connect to any other driver, VSS or VDD ; Pins can be
left open
32, 33, 34, 35 TESTIO...3 I Input stages (internal pull-down) ; Pins can be left open
S : supply, I : input, O : output, TTL : digital (TTL)
24
IC description
5-5. DDP 3310B (Display and Deflection Processor)

(1) Description Deflection processing
The DDP 3310B is a single-chip digital Display and Deflec- - scan velocity modulation output
tion Processor designed for high-quality backend applica- - high-performance H/V deflection
tions in 100/120MHz TV sets with 4:3- or 16:9 picture - EHT compensation for vertical / East/West
tubes. The IC can be combined with members of the - soft start/stop of H-Drive
DIGIT 3000 IC family (VPC 32xx, TPU 3040), or it can be - vertical angle and bow
used with third-party products. The IC contains the entire - differential vertical output
digital video component and deflection processing and all - horizontal and vertical protection circuit
analog interface components. - adjustable horizontal frequency for VGA/SVGA dislay
(2) Feature Miscellaneous

Video processing - selectable 4:1:1/4:2:2 YC rC binput
- linear horizontal scaling (0.25 ... 4) - selectable 27/32-MHz line-locked clock input
- non-linear horizontal scaling “panoramavision” - crystal oscillator for horizontal protection
- dynamic peaking - automatic picture tube adjustment(cutoff, whitedrive)
- soft limiter (gamma correction) - single 5-V power supply
- color transient improvement - hardware for simple 50/60-Hz to 100/120-Hz conversion
- programmable RGB matrix (display frequency doubling)
- picture frame generator - two I2C -controlled PWM outputs
- two analog RGB/Fast-Blank inputs - beam current limiter
(3) Block Diagram
25
IC description
(4) Pin Description The vertical protection circuitry prevents the picture tube
from burn-in in the event of a malfunction of the vertical
Pin 1 - Supply Voltage, Output Pin Driver VSUPP* deflection stage. If the peak-to-peak value of the vertical
This pin is used as supply for the following digital output sawtooth signal is too small, the RGB output signals are
pins : FIFORRD, FIFORD, FIFOWR, FIFORWR. blanked.
Pin 2 - Ground, Output Pin Driver GNDP* Pin 12 - H-Drive Frequency Range Select FREQSEL
Output Pin Driver Reference This pin selects the frequency range for the horizontal
drive signal.
Pin 3 - Sync Signal Input VS2
Additional pin for the vertical sync information. Via I2C Pin 13 - Clock Select 40.5 or 27/32 MHzCM1
Register the used vertical sync can be switched between Low level selects 27/32 MHz, High level selects 40.5 MHz
the inputs VS2 and VS(Pin 64)
Pin 14 - Clock Select 40.5 or 27/32 MHzCM0
Pin 4 - Reset for FIFO Read Counter FIFORRD Low level selects 27 MHz, High level selects 32 MHz
This signal is active-High and resets the read counter in
the display frequency doubling FIFO. Pin 15 - Range Switch2 for Measuring ADC RSW2
This pin is an open-drain pull-down output. During cutoff
measurement the switch is off. During white drive mea-
Pin 5 - Read Enable for FIFO FIFORD
surement the switch is on. Also during the rest of time it is
This signal is active-High and enabels the read counter in on.
the display frequency doubling FIFO.
Pin 16 - Range Switch 1 or Second Input for Measuring
Pin 6 - Write Enable for FIFO FIFOWR ADC RSW1
This signal is active-High and enables the write counter in This pin is an open-drain pull-down output. During cutoff
the display frequency doubling FIFO. and white-drive measurement, the switch is off. During
the rest of time it is on. The RSW1 pin can be used as
second measurement ADC input.
Pin 7 - Reset for FIFO Write Counter FIFOWR
This signal is active-High and enables the write counter in
Pin 17 - Measurement ADC Input SENSE
the display frequency doubling FIFO.
This is the input of the analog to digital converter for the
picture and tube measurement. Three measurement
Pin 8 - Horizontal Drive HOUT ranges are selectable with RSW1 and RSW2
This open-drain output supplies the drive pulse for the hor-
izontal output stage. A pull-up resistor has to be used. Pin 18 - Measurement ADC Reference Input MGND
This is the ground reference for the measurement A/D
Pin 9 - Horizontal Flyback Input HFLB converter.
Via this pin, the horizontal flyback pulse is supplied to the
Pin 19 - Vertical Sawtooth Output VERT+(19)
DDP 3310B.
This pin supplies the drive signal for the vertical output
stage. The drive signal is generated with 15-bit precision.
Pin 10 - Safety Input SAFETY The analog voltage is generated by a 4-bit current DAC
This input has two thresholds. A signal between the lower with external resistor (6 k§
Ù for proper operation) and
and upper threshold means normal function. Other signals uses digital noise-shaping.
are detected as malfunction.
Pin 20 - Vertical Sawtooth Output inverted VERT-
Pin 11 - Vertical Protection Input VPROT This pin supplies the inverted signal of VERT+.
26
IC description
Together with this pin, it can be used to drive symmetrical These pins are used to switch the RGB outputs to the
deflection amplifiers. external analog RGB inputs. FBLIN1 switches the RIN1,
GIN1 and BIN1 inputs, FBLIN2 switches the RIN2, GIN2
Pin 21 - East/West Parabola Output EW and BIN2 inputs. The active level (Low or High) can be
This pin supplies the parabola signal for the East/West selected by software.
correction. The drive signal is generated with 15-bit preci-
sion. The analog voltage is generated by a 4-bit current Pin 31, 32, 33 - Analog RGB Input1 RIN1, GIN1, BIN1
DAC with external resistor and uses digital noise-shaping. These pin are used to insert an external analog RGB sig-
nal, e.g. from a SCART connector which can by switched
Pin 22 - DAC Current Reference XREF to the analog RGB outputs with the Fast-Blank signal.
External reference resistor for DAC output currents, typical The analog back-end provides separate brightness and
10 k§Ù , to adjust the output current of the D/A converters. contrast settings for the external analog RGB signals.
(see recommended operation conditions).
This resistor has to be connected to analog fround as Pin 35, 36, 37 - Analog RGB Input2 RIN2, GIN2, BIN2
closely as possible to the pin. These pins are used to insert an external analog RGB sig-
nal, e.g. from a SCART connector which can by switched
Pin 23 - Scan Velocity Modulation Output SVM to the analog RGB outputs with the Fast-Blank signal.
This output delivers the analog SVM signal. The D/A con- The analog back-end provides separate brightness and
verters. At zero signal the output current is 50% of the contrast settings for the external analog RGB signals.
maximum output current.
Pin 38 - Test Input TEST
Pin 24,25,26 - Analog RGB Output ROUT, GOUT, BOUT This pin enables factory test modes. For normal operation
These pins are the analog Red/Green/Blue outputs of the it must be connected to ground.
back-end. The outputs are current sinks.
Pin 39 - Reset Input RESQ
Pin 27 - Ground, Analog Back-end GNDO* A low level on this pin resets the DDP 3310B.
This pin has to be connected to the analog supply voltage.
No supply current for the digital stages should flow through Pin 40 - Adjustable DC Output 1 PWM1
this line. This output delivers a DC voltage with a resolution of 8
bit, adjustable over the I2Cbus. The output is driven by a
push-pull stage. The PWM frequency is appr 79.4MHz.
Pin 28 - Supply Voltage, Analog Back-end VSUPO* For a ripple-free voltage a first order lowpass filter with a
This pin has to be connected to the analog supply voltage. corner frequency < 120 Hz should be applied.
No supply current for the digital stages should flow through
this line. Pin 41 - Adjustable DC Output 2 PWM2
See pin 40.
Pin 29 - DAC Reference Decouplign/Beam Current Safety
VRD/BCS Pin 42 - Half-Contrast Input HCS
Via this pin, the DAC reference voltage is decoupled by an Via this input pin the output level of the D/A-converted
external capacitor. The DAC output currents depend on internal RGB signals can be reduced by 6dB. Inserted
external analog RGB signals remain unchanged.
this voltage, therefore a pull-down transistor can be used
to shut off all beam currents. A decoupling capacitor of Pin 43...50 - Picture Bus Chroma C0...C7
4.7uF in parallel to 100uF (low inductance) is required. The Picture Bus Chroma lines carry the multiplexed color
component data. For the 4:1:1 input signal (4-bit chroma)
Pin 30, 34 - Fast-Blank Input FBLIN1/2 the pins C4...C7 are used.
27
IC description
Pin 51 - Supply Voltage, Digital Circuitry VSUPD* Pin 65, 66 - Crystal Output / Input XTAL2 / XTAL1
These pins are connectecd to an 5-MHz crystal oscillator.
Pin 52 - Ground, Digital Circuitry GNDD* The security unit for the HOUT signal uses this clock sig-
Digital Circuitry Input Reference nal as reference.
2
Pin 53 - Main Clock Input LLC2(53) Pin 67 - I C Data Input/Output SDA
This is the input for the line-locked clock signal. The fre- Via this pin the I2C - bus data are written to or read from
quency can be 27, 32, or 40.5 MHz. the DDP 3310B.
Pin 54...61 - Picture Bus Luma Y0...Y7 Pin 68 - I2C Clock Input SCL
The Picture Bus Luma lines carry the digital luminance Via this pin, the clock signal for the I2C-bus will be sup-
plied. The signal can be pulled down by an internal tran-
data.
sistor.
Pin 62 - Line-Locked Clock Input LLC1 * Application Note :

This is the reference clock for the single frequency input All ground pins should be connected separeately with
sync signals required in a FIFO application. The frequency short and low-resistive lines to a central power supply
can be 13.5, 16, or 20.25 MHz. ground. Accordingly, all supply pins should be connected
separately with short and low-resistive lines to the power
Pin 63 - Sync Signal Input HS supply. Decoupling capacitors from VSUPP to GNDP,
This pin gets the horizontal sync information. Either single VSUPD to GNDD, and VSUPO to GNDO are recom-
or double horizontal frequency or VGA horizontal sync sig- mended to be placed as closely as possible to the pins.
nal.
Pin 64 - Sync Signal Input VS

This pin gets the vertical sync informatoion. Either single
or double vertical frequency or VGA vertical sync signal.
28
IC description
5-6. DPL 3519A (Dolby Pro Logic Processor)

The DPL 3519A is designed as a coprocessor to the MSP family but has analog output channels in addition to the fea-
tures of the DPL 3518A. Together with the MSP, a TV set with up to six outputs (L, R, C, SUB, SL, SR)can be developed
together with headphones and several line outputs.
(2) Features
- Full Dolby Surround Pro Logic Adative Matrix
- Pseudo-surround mode for signals not encoded in dolby Surround
- PANORAMA sound mode(3-D Surround sound via 2 loudspeakers)
- Noise sequencer
- Automatic input balance control
- 7 kHz low-pass filter
- 100 Hz low-pass filter for subwoofer
- Modified Dolby B-type NR decoder
- 30 ms surround delay according to table created by Dolby Labortories (1 ms steps)
2
- 2 I S input channels (e.g. MSP and DRPA)
2
- 2 I S output channels, freely programmable with sound channels L/R ( resp. L+C/R+C), C/S, Sub or I2S input
- Mode control : normal/phantom/wide/three channel/center off/panorama sound/stereo bypass
- Surround matrix mode control : adaptive/passive/effect
- Additional surround basswidth effect
- Reverberation of surround signals
- 2 digital input/output pins
- 1 digital input pin
- Master volume control in dB units
- Level Trim for L, C, R, S in dB units, +_12dB
- Identical treble/bass/loudness function for L, C, R, S
- 5-band equalizer for C channel
- Separate volume control for two surround outputs
- Additional line output for HIFI receiver connection (SCART output). Volume for this output is in dB units.
- 3 pairs of D/A converters
- Scart switches
29
IC description
(3) Block Diagram
(4) Pin Description

Pin No. PIN Name Type Description
1 D_CTR_IN IN Digital control input
2 AUD_CL_OUT OUT Audio clock output
3 D_CTR_IO1 IN/OUT Digital control IO1
4 D_CTR_IO1 IN/OUT Digital control IO 0
5 ADR_SEL IN I 2 C -Bus address select
6 STANDBYQ IN Standby (low-active)
7 I2C_CL IN I 2 C clock
8 I2C_DA IN/OUT I 2 C data
9 I2C_CL OUT I2 C clock
10 I2C_WS OUT I 2 C wordstrobe
11 I2C_DA_OUT1 OUT I 2 C data output
12 I2C_DA_IN1 IN I 2 C data input
13 NC Not connected
14 NC Not connected
15 NC Not connected
16 DVSUP Digital power supply +5V
17 DVSS Digital ground
18 I2S_DA_IN2 IN I 2 S 2 - data input
30
IC description
Pin No. PIN Name Type Description

19 I2S_DA_OUT OUT 2-
I S data output
2
20 RESETQ IN Power-on-reset
21 20/19:DACC2_R 18:NC OUT Analog output Channel2, right
22 20/19:DACC2_R 18:NC OUT Analog output Channel2, left
23 20/19:VREF2 18:NC Reference ground2 high voltage part
24 20/19:DACC1_R 18:NC OUT Analog output Channel1, right
25 20/19:DACC1_L 18:NC OUT Analog output Channel1, left
26 NC Not connected
27 20/19:SC2_OUT_R 18:NC OUT Scart output2, right
28 20/19:SC2_OUT_L 18:NC OUT Scart output2, left
29 20/19:VREF1 18:NC Reference ground1 high voltage part
30 20/19:SC1_OUT-R 18:NC OUT Scart output1, right
31 20/19:SC1_OUT-L 18:NC OUT Scart output1, left
32 20/19:CAPL_C2 18:NC Volume capacitor Channel2
33 20/19:AHVSUP 18:NC Analog power supply +8V
34 20/19:CAPL_C1 18:NC Volume capacitor Channel1
35 20/19:AHVSS 18:NC Analog ground
36 20/19:AGNDC 18:NC Analog reference voltage high voltage part
37 20/19:SC3_IN_L 18:NC IN Scart input3 in, left
38 20/19:SC3_IN_R 18:NC IN Scart input3 in, right
43 VREFTOP Reference voltage
44 20/19:MONO_IN 18:NC IN Mono input
45 AVSS Analog ground
46 AVSUP Analog power supply +5V
47 NC Not connected
48 NC Not connected
49 NC Not connected
50 TESTEN IN Test pin
51 XTAL_IN IN Crystal oscillator
52 XTAL_OUT OUT Crystal oscillator
31
6. IC DC Voltage Charts
* Input signal PAL/CH5 - Video : 8 step colour bar ( 87% AM )
Audio : 1KHz sinewave ( 60% FM )
* User’s control condition Contrast, Brightness, Colour, Volume Controls-max.
* Line voltage AC 230V, 50Hz
* All the voltage in each point are measured with Multimeter.
1. TDA 8172 (I301)
Pin No. 1 2 3 4 5 6 7
V(DC) 0.4 +10.7 -8.7 -10.6 0 11.1 0.4
2. MSP 3415D (I606)
Pin No. 1 2 3 4 5 6 7 8 9 10
V(DC) 2.5 0 0 0 0 0 5.0 0 5.0 5.0
Pin No. 11 12 13 14 15 16 17 18 19 20
V(DC) 2.4 2.4 2.4 0.5 0.6 0.6 0.5 4.9 0 1.3
Pin No. 21 22 23 24 25 26 27 28 29 30
V(DC) 0.4 0.4 0.3 4.9 0.7 0.7 0 0.08 0.08 0
Pin No. 31 32 33 34 35 36 37 38 39 40
V(DC) 0.08 1.0 3.8 3.8 0 3.8 3.8 7.2 8.0 7.2
Pin No. 41 42 43 44 45 46 47 48 49 50
V(DC) 0 3.7 0 0 0 3.7 3.7 0 3.7 3.7
Pin No. 51 52 53 54 55 56 57 58 59 60
V(DC) 0 3.7 3.7 2.6 1.1 0 4.9 1.5 1.5 0
Pin No. 61 62 63 64
V(DC) 0 2.4 2.4 0.5
3. TDA 4470-M (I101)
Pin No. 1 2 3 4 5 6 7 8 9 10
V(DC) 3.2 3.2 3.5 0 1.1 2.4 2.4 2.0 0 1.2
Pin No. 11 12 13 14 15 16 17 18 19 20
V(DC) 1.7 2.1 4.4 3.9 2.6 0 4.2 2.2 3.5 3.3
Pin No. 21 22 23 24 25 26 27 28
V(DC) 3.3 2.3 4.8 2.1 2.0 0.7 0.1 0.1
32
IC DC Voltage Charts
4. TDA 7269 (I601)
Pin No. 1 2 3 4 5 6 7 8 9 10 11
V(DC) -14.2 0 +14.2 0 0 -14.2 0 0 5.0 5.0 0
5. ST92195 (I701)
Pin No. 1 2 3 4 5 6 7 8 9 10
V(DC) 3.1 4.8 0 0 0 0 0 0 0 0.5
Pin No. 11 12 13 14 15 16 17 18 19 20
V(DC) 5.0 0 0 0 0.4 0.4 0.4 0 5.0 5.0
Pin No. 21 22 23 24 25 26 27 28 29 30
V(DC) 5 0.7 0 0 5.0 0 1.8 0.6 2.1 0.8
Pin No. 31 32 33 34 35 36 37 38 39 40
V(DC) 5.0 5.0 0.8 1.6 0 0 0 2.0 5.0 0.6
Pin No. 41 42 43 44 45 46 47 48 49 50
V(DC) 0 0 0 0.1 5.0 0 0 0 0 2.3
Pin No. 51 52 53 54 55 56
V(DC) 2.3 5.0 5.0 0.6 2.3 0
6. AT24C16-10PC (I702)
Pin No. 1 2 3 4 5 6 7 8
V(DC) 0 0 5.0 0 5.0 5.0 0 5.0
7. STR-F6654 (I801)
Pin No. 1 2 3 4 5
V(DC) 2.0 0 254.0 18.0 0
8. DPL 3519A
Pin No. 1 2 3 4 5 6 7 8 9 10
V(DC) 0.5 2.7 0.5 0.5 3.8 4.9 5.0 5.0 2.4 2.4
Pin No. 11 12 13 14 15 16 17 18 19 20
V(DC) 0.5 2.4 0.5 0.5 0.5 4.9 0 0.4 0 3.7
Pin No. 21 22 23 24 25 26 27 28 29 30
V(DC) 0.1 0.1 0 0.1 0.1 0 3.7 3.7 0 3.7
33
IC DC Voltage Charts
Pin No. 31 32 33 34 35 36 37 38 39 40
V(DC) 3.7 6.8 7.8 6.8 0 3.7 3.7 3.7 3.7 3.7
Pin No. 41 42 43 44 45 46 47 48 49 50
V(DC) 3.7 3.7 2.6 3.7 0 5.0 1.5 1.5 0.4 0
Pin No. 51 52
V(DC) 2.2 2.1
9. TEA5101B (I901)
Pin No. 1 2 3 4 5 6 7 8 9 10
V(DC) 3.2 12.2 3.2 3.2 210.0 0.6 172.0 0 115.0 177.0
Pin No. 11 12 13 14 15
V(DC) 0.6 119.0 168.0 0.6 116.0
10. P503
Pin No. 1 2 3 4 5 6 7 8 9 10
V(DC) 0 5.0 1.0 1.0 0 1.9 0 0 0 0.6
Pin No. 11 12 13 14 15 16 17 18
V(DC) -0.3 0 4.9 0.6 0.4 0.4 0.4 12.1
11. P504
Pin No. 1 2 3 4 5 6 7 8 9 10
V(DC) 0.9 0 0 0.8 0 0 1.2 0 0 0
Pin No. 11 12 13 14 15 16 17 18
V(DC) 5 5 70 0.6 0 3 3 3
34
7. Service Parts List/Recommendable Spare Parts List
Caution R is recommendable spare part.
is safety component, so it must be used the same component.
LOC PART CODE PART NAME DESCRIPTION REMARK LOC PART CODE PART NAME DESCRIPTION REMARK
ZZ100 48B3822D05 TRANSMITTER R-22D05 R P601A 4850704S30 CONNECTOR YH025-
REMOCON 04+35098+ULW=700
ZZ110 PTACPWD228 ACCESSORY AS DTJ-28G6F SP01 4858311110 SPEAKER 12W 8 OHM SP-58126F
10 4850Q00910 BATTERY R03/NN SP02 4858311110 SPEAKER 12W 8 OHM SP-58126F
20 4859102620 JACK ANT 3104.308.73221 ZZ290 PTMPMSD228 PCB MAIN MANUAL DTJ-28G6F R
M821 4858213800 BAG INSTRUCTION L.D.P.E T0.05X250X400 AS
ZZ120 PTBCSHD310 COVER BACK AS DTJ-28A6F 1 DFMLG12S-- DIODE FML-G12S
M211 4852156501 COVER BACK HIPS BK 0000A 4857026900 HEAT SINK AL EX
M211D 4857817611 CLOTH BLACK FELT 200X20X0.7 0000B 7174301011 SCREW TAPPTITE TT2 RND 3X10 MFZN
M541 4855415800 SPEC PLATE 150ART P/E FILM (C/TV) C100 CXRH1H150J C CERA RH 50V 15PF J (TAPPING)
ZZ130 PTPKCPD310 PACKING AS DTJ-28A6F C101 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11) TP
M641 6520010100 STAPLE PIN 18M/M J D O C102 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP
M681 4856812400 BAND 18MM X 3M C103 CEXF1E330V C ELECTRO 25V RSS 33MF (5X11) TP
M801 4858054600 BOX CARTON SW-2 C104 CXCH1H220J C CERA 50V CH 22PF J (TAPPING)
M811 4858193801 PAD EPS 28A6 C107 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP
M822 4858215600 BAG P.E PE FOAM T0.5X1600X1270 C109 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11) TP
ZZ131 58G0000103 COIL DEGAUSSING DC-2701 C117 CEXF1H229V C ELECTRO 50V RSS 2.2MF (5X11) TP
ZZ132 48519A5510 CRT GROUND NET 2801H-1015-2P C303 CMXM2A683J C MYLAR 100V 0.068MF J (TP)
ZZ140 PTCACAD310 CABINET AS DTJ-28A6F C305 CEXF1V101C C ELECTRO 35V RUS 100MF (8X11.5)
M201A 4857818701 CLOTH BLACK FELT T0.7 L=250 W=15 TP
M201B 4857818702 CLOTH BLACK FELT T0.7 L=350 W=15 C401 CEXF1E101V C ELECTRO 25V RSS 100MF (6.3X11)
M211A 7172401612 SCREW TAPPTITE TT2 TRS 4X16 MFZN BK TP
M211B 7178301212 SCREW TAPPTITE TT2 WAS 3X12 MFZN BK C402 CMYH3C432J C MYLAR 1.6KV BUP 4300PF J
M281 4852822401 DOOR PC CL C403 CEXF1C102C C ELECTRO 16V RUS 1000MF (10X20)
M352 97P4602700 CLAMP CORD NYLON 66 BLK 5280N TP
M391A 7172401612 SCREW TAPPTITE TT2 TRS 4X16 MFZN BK C404 CMYH3C622J C MYLAR 1.6KV BUP 6200PF J
M481 4854856801 BUTTON POWER HIPS BK C405 CMYE2J223J C MYLAR 630V PU 0.022MF J
M481A 4856716000 SPRING SWPA PIE0.5 C406 CEXF1E471C C ELECTRO 25V RUS 470MF (10X16)
M491A 7178301011 SCREW TAPPTITE TT2 WAS 3X10 MFZN TP
M501 4855059601 DECO CTRL PVC T0.25 C407 CEXF1H100C C ELECTRO 50V RUS 10MF (5X11) TP
M561 4855617401 MARK BRAND AL (SILVER) C408 CMYE2G334J C MYLAR 400V PU 0.33MF J
M681 4856812001 TIE CABLE NYLON66 DA100 C409 CMXB1H273J C MYLAR 50V EU 0.027MF J (TP)
M682 4856816300 CLAMP WIRE NYLON 6 (V0) C411 CEXF2C109V C ELECTRO 160V RSS 1MF (6.3X11) TP
M791 4857923300 DOOR LOCK LA701(KIFCO) C412 CEXF1E101V C ELECTRO 25V RSS 100MF (6.3X11)
P405 4850704N07 CONNECTOR SE100J+172792+USW=500 TP
SP01A 7172401212 SCREW TAPPTITE TT2 TRS 4X12 MFZNCK C413 CEXF1C102V C ELECTRO 16V RSS 1000MF (10X20)
SP02A 7172401212 SCREW TAPPTITE TT2 TRS 4X12 MFZNCK TP
V901 4859625760 CRT A66EAK071X54 R C415 CEXF2E100V C ELECTRO 250V RSS 10MF (10X20) TP
V901A 4856215402 WASHER RUBBER CR T2.0 C416 CCXB3D471K C CERA 2KV B 470PF K (TAPPING)
V901B 4856015820 SCREW CRT FIX SWRM+SK5 L=35 C417 CMXM2A222J C MYLAR 100V 2200PF J (TP)
ZZ200 PTFMSJD310 MASK FRONT AS DTJ-28A6F R C418 CEYD1H689W C ELECTRO 50V RHD 6.8MF (16X35.5)
M201 4852074501 MASK FRONT HIPS BK C420 CCXB1H472K C CERA 50V B 4700PF K (TAPPING)
M251 4852540601 GRILL L PS SHEET C501 CEXF1E101V C ELECTRO 25V RSS 100MF (6.3X11)
M252 4852538401 GRILL R PS SHEET TP
ZZ220 PTSPPWD228 SPEAKER AS DTJ-28G6F R C601 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z
35
Service Parts List/Recommendable Spare Parts List
C602 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z C826 CEXF1E101V C ELECTRO 25V RSS 100MF (6.3X11)
C603 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP TP
C605 CEXF1E471C C ELECTRO 25V RUS 470MF (10X16) C827 CEXF1E471C C ELECTRO 25V RUS 470MF (10X16)
TP TP
C606 CEXF1E471C C ELECTRO 25V RUS 470MF (10X16) C830 CEXF1E101V C ELECTRO 25V RSS 100MF (6.3X11)
TP TP
C619 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11) TP C831 CEXF1E222V C ELECTRO 25V RSS 2200MF (16X25)
C620 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11) TP TP
C625 CEXF1H479C C ELECTRO 50V RUS 4.7MF (5X11) TP C832 CEXF1E222V C ELECTRO 25V RSS 2200MF (16X25)
C626 CEXF1H479C C ELECTRO 50V RUS 4.7MF (5X11) TP TP
C627 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP C836 CEXF1E471C C ELECTRO 25V RUS 470MF (10X16)
C655 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP C837 CEXF1E101V C ELECTRO 25V RSS 100MF (6.3X11)
C658 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP C840 CXSL2H470J C CERA 500V SL 47PF J (TAPPING)
C674 CEXF1H479C C ELECTRO 50V RUS 4.7MF (5X11) TP C841 CBZF1H104Z C CERA SEMI 50V F 0.1MF Z
C675 CEXF1H479C C ELECTRO 50V RUS 4.7MF (5X11) TP C842 CEXF1E471C C ELECTRO 25V RUS 470MF (10X16)
C702 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP C843 CEXF1E471C C ELECTRO 25V RUS 470MF (10X16)
C705 CEXF1E470V C ELECTRO 25V RSS 47MF (5X11) TP C910 CEXF2E100V C ELECTRO 250V RSS 10MF (10X20) TP
C731 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP C911 CEXF2E100V C ELECTRO 250V RSS 10MF (10X20) TP
C801 CL1JB3474K C LINE ACROSS AC250V 0.47MF U/C/SNDF/ C912 CCXB3D102K C CERA 2KV B 1000PF K (TAPPING)
SV C913 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP
C802 CL1JB3474K C LINE ACROSS AC250V 0.47MF U/C/SNDF/ CC101 HCBK102KCA C CHIP CERA 50V X7R 1000PF K 2012
SV CC102 HCBK102KCA C CHIP CERA 50V X7R 1000PF K 2012
C805 CCXF3A472Z C CERA 1KV F 4700PF Z (T) CC103 HCBK102KCA C CHIP CERA 50V X7R 1000PF K 2012
C806 CCXF3A472Z C CERA 1KV F 4700PF Z (T) CC104 HCQK220JCA C CHIP CERA 50V CH 22PF J 2012
C808 CCZB1H681K C CERA 50V B 680PF K (AXIAL) CC105 HCTAD100MB C CHIP TANTAL 10V 10MF M 3216
C809 CEYA2G221G C ELECTRO 400V LSS 220MF (30X40) CC106 HCFK103ZCA C CHIP CERA 50V Y5V 0.01MF Z 2012
C810 CBYB3D152K C CERA SEMI 2KV BL(N) 1500PF K CC107 HCFK104ZCA C CHIP CERA 50V Y5V 0.1MF Z 2012
C812 CEXF1H220V C ELECTRO 50V RSS 22MF (5X11) TP CC108 HCFK103ZCA C CHIP CERA 50V Y5V 0.01MF Z 2012
C813 CCXB3A471K C CERA 1KV B 470PF K (T) CC109 HCFK104ZCA C CHIP CERA 50V Y5V 0.1MF Z 2012
C814 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP CC110 HCFK103ZCA C CHIP CERA 50V Y5V 0.01MF Z 2012
C815 CEYF2D101V C ELECTRO 200V RSS 100MF (16X31.5) CC112 HCFK103ZCA C CHIP CERA 50V Y5V 0.01MF Z 2012
C816 CEYF2D101V C ELECTRO 200V RSS 100MF (16X31.5) CC114 HCFK103ZCA C CHIP CERA 50V Y5V 0.01MF Z 2012
C817 CEXF1H470V C ELECTRO 50V RSS 47MF (6.3X11) TP CC115 HCBK102KCA C CHIP CERA 50V X7R 1000PF K 2012
C818 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP CC116 HCTAF229MB C CHIP TANTAL 16V 2.2MF M 3216
C819 CEXF2A100V C ELECTRO 100V RSS 10MF (6.3X11) CC118 HCFK474ZCA C CHIP CERA Y5V 50V 0.47MF Z 2012
TP CC120 HCFK103ZCA C CHIP CERA 50V Y5V 0.01MF Z 2012
C820 CEXF1C332V C ELECTRO 16V RSS 3300MF (16X25) CC302 HCBK223KCA C CHIP CERA 50V X7R 0.022MF K 2012
TP CC303 HCBK223KCA C CHIP CERA 50V X7R 0.022MF K 2012
C821 CCXB3D681K C CERA 2KV B 680PF K (TAPPING) CC306 HCBK333KCA C CHIP CERA 50V X7R 0.033MF K 2012
C822 CH1AFE472M C CERA AC 4KV 4700PF M KX DE1610 CC401 HCBK223KCA C CHIP CERA 50V X7R 0.022MF K 2012
C823 CEXF1E101V C ELECTRO 25V RSS 100MF (6.3X11) CC601 HCQK470JCA C CHIP CERA 50V CH 47PF J 2012
TP CC603 HCFK105ZCA C CHIP CERA 50V Y5V 1MF Z 2012
36
CC604 HCFK103ZCA C CHIP CERA 50V Y5V 0.01MF Z 2012 CC701 HCBK102KCA C CHIP CERA 50V X7R 1000PF K 2012
CC609 HCBK102KCA C CHIP CERA 50V X7R 1000PF K 2012 CC702 HCFK103ZCA C CHIP CERA 50V Y5V 0.01MF Z 2012
CC610 HCBK102KCA C CHIP CERA 50V X7R 1000PF K 2012 CC704 HCBK472KCA C CHIP CERA 50V X7R 4700PF K 2012
CC611 HCTAD100MB C CHIP TANTAL 10V 10MF M 3216 CC705 HCBK222KCA C CHIP CERA 50V X7R 2200PF K 2012
CC612 HCBK102KCA C CHIP CERA 50V X7R 1000PF K 2012 CC706 HCQK220JCA C CHIP CERA 50V CH 22PF J 2012
CC614 HCFK104ZCA C CHIP CERA 50V Y5V 0.1MF Z 2012 CC707 HCFK103ZCA C CHIP CERA 50V Y5V 0.01MF Z 2012
CC617 HCFK105ZCA C CHIP CERA 50V Y5V 1MF Z 2012 CC708 HCFK474ZCA C CHIP CERA Y5V 50V 0.47MF Z 2012
CC618 HCFK105ZCA C CHIP CERA 50V Y5V 1MF Z 2012 CC709 HCQK820JCA C CHIP CERA 50V CH 82PF J 2012
CC620 HCBK223KCA C CHIP CERA 50V X7R 0.022MF K 2012 CC711 HCBK102KCA C CHIP CERA 50V X7R 1000PF K 2012
CC621 HCQK509DCA C CHIP CERA 50V CH 5PF D 2012 CC713 HCQK820JCA C CHIP CERA 50V CH 82PF J 2012
CC622 HCQK509DCA C CHIP CERA 50V CH 5PF D 2012 CC715 HCFK103ZCA C CHIP CERA 50V Y5V 0.01MF Z 2012
CC628 HCTAD100MB C CHIP TANTAL 10V 10MF M 3216 CC719 HCQK220JCA C CHIP CERA 50V CH 22PF J 2012
CC629 HCFK104ZCA C CHIP CERA 50V Y5V 0.1MF Z 2012 CC720 HCFK105ZCA C CHIP CERA 50V Y5V 1MF Z 2012
CC630 HCTAF339MB C CHIP TANTAL 16V 3.3MF M 3216 CC721 HCBK102KCA C CHIP CERA 50V X7R 1000PF K 2012
CC631 HCTAD100MB C CHIP TANTAL 10V 10MF M 3216 CC801 HCFK104ZCA C CHIP CERA 50V Y5V 0.1MF Z 2012
CC635 HCBK472KCA C CHIP CERA 50V X7R 4700PF K 2012 CC834 HCFK104ZCA C CHIP CERA 50V Y5V 0.1MF Z 2012
CC638 HCFK105ZCA C CHIP CERA 50V Y5V 1MF Z 2012 CC906 HCBK102KCA C CHIP CERA 50V X7R 1000PF K 2012
CC639 HCFK105ZCA C CHIP CERA 50V Y5V 1MF Z 2012 CC907 HCFK104ZCA C CHIP CERA 50V Y5V 0.1MF Z 2012
CC640 HCBK102KCA C CHIP CERA 50V X7R 1000PF K 2012 CCA10 HCBK331KCA C CHIP CERA 50V X7R 330PF K 2012
CC641 HCBK102KCA C CHIP CERA 50V X7R 1000PF K 2012 CCA20 HCBK331KCA C CHIP CERA 50V X7R 330PF K 2012
CC644 HCFK104ZCA C CHIP CERA 50V Y5V 0.1MF Z 2012 D101 D1N4148--- DIODE 1N4148 (TAPPING)
CC645 HCFK103ZCA C CHIP CERA 50V Y5V 0.01MF Z 2012 D102 D1SS85TA-- DIODE 1SS85TA
CC646 HCFK103ZCA C CHIP CERA 50V Y5V 0.01MF Z 2012 D301 D1N4936GP- DIODE 1N4936GP (TAPPING)
CC653 HCBK102KCA C CHIP CERA 50V X7R 1000PF K 2012 D302 DUZ5R1B--- DIODE ZENER UZ-5.1B UNIZON
CC654 HCBK102KCA C CHIP CERA 50V X7R 1000PF K 2012 D404 DDMV32F5-- DIODE DMV32F5
CC656 HCQK471JCA C CHIP CERA 50V CH 470PF J 2012 D404A 7174300811 SCREW TAPPTITE TT2 RND 3X8 MFZN
CC660 HCBK333KCA C CHIP CERA 50V X7R 0.033MF K 2012 D405 D1N4936GP- DIODE 1N4936GP (TAPPING)
CC662 HCTAD100MB C CHIP TANTAL 10V 10MF M 3216 D407 D1N4936GP- DIODE 1N4936GP (TAPPING)
CC663 HCBK102KCA C CHIP CERA 50V X7R 1000PF K 2012 D408 D1N4936GP- DIODE 1N4936GP (TAPPING)
CC665 HCFK105ZCA C CHIP CERA 50V Y5V 1MF Z 2012 D410 D1N4937G-- DIODE 1N4937G
CC666 HCFK105ZCA C CHIP CERA 50V Y5V 1MF Z 2012 D411 D1N4148--- DIODE 1N4148 (TAPPING)
CC669 HCTAH109MB C CHIP TANTAL 25V 1MF M 3216 D412 D1N4148--- DIODE 1N4148 (TAPPING)
CC670 HCTAH109MB C CHIP TANTAL 25V 1MF M 3216 D413 D1N4148--- DIODE 1N4148 (TAPPING)
CC671 HCTAF339MB C CHIP TANTAL 16V 3.3MF M 3216 D414 D1N4148--- DIODE 1N4148 (TAPPING)
CC672 HCTAD100MB C CHIP TANTAL 10V 10MF M 3216 D415 D1N4937G-- DIODE 1N4937G
CC673 HCTAD100MB C CHIP TANTAL 10V 10MF M 3216 D501 DUZ8R2BM-- DIODE ZENER UZ-8.2B (8.2V)
CC676 HCTAD479MB C CHIP TANTAL 10V 4.7MF M 3216 D502 DUZ8R2BM-- DIODE ZENER UZ-8.2B (8.2V)
CC677 HCTAD479MB C CHIP TANTAL 10V 4.7MF M 3216 D503 DUZ8R2BM-- DIODE ZENER UZ-8.2B (8.2V)
37
D701 D1N4148--- DIODE 1N4148 (TAPPING) DA20 DUZ5R6BM-- DIODE ZENER UZ-5.6BM(TAPPING)
D703 DUZ5R1B--- DIODE ZENER UZ-5.1B UNIZON DA21 DUZ5R6BM-- DIODE ZENER UZ-5.6BM(TAPPING)
D706 DUZ5R6BM-- DIODE ZENER UZ-5.6BM(TAPPING) DA23 DUZ5R6BM-- DIODE ZENER UZ-5.6BM(TAPPING)
D707 DSR54MVW3- LED SPR54 MVW RED/GREEN DA24 DUZ5R6BM-- DIODE ZENER UZ-5.6BM(TAPPING)
D707A 4853533600 HOLDER LED P.P BK DA25 DUZ5R6BM-- DIODE ZENER UZ-5.6BM(TAPPING)
D801 DLT2A05G-- DIODE LT2A05G (TP) DA30 DUZ5R1B--- DIODE ZENER UZ-5.1B UNIZON
D804 DLT2A05G-- DIODE LT2A05G (TP) F801 5FSCB4022R FUSE CERA SEMKO F4AH 4A 250V
D805 DEU1Z----- DIODE EU1Z (HIGH SPEED) MF51
D806 DEU1Z----- DIODE EU1Z (HIGH SPEED) F801A 4857415001 CLIP FUSE PFC5000-0702
D807 DEU1Z----- DIODE EU1Z (HIGH SPEED) F801B 4857415001 CLIP FUSE PFC5000-0702
D808 D1N4937G-- DIODE 1N4937G G901 4SG0D00103 SPARK GAP S-23 900V-1.5KV
D809 DRGP30J--- DIODE RGP30J G902 4SG0D00103 SPARK GAP S-23 900V-1.5KV
D810 D1N4936GP- DIODE 1N4936GP (TAPPING) G903 4SG0D00103 SPARK GAP S-23 900V-1.5KV
D811 DUZ7R5BM-- DIODE ZENER UZ-7.5BM 7.5V HP01 4859102130 JACK EARPHONE YSC-1537
D812 PTP2SW6900 HEAT SINK ASS`Y DFMLG12S-- + 7174301011 I101 1TDA4470M- IC IF TDA4470-M
D813 D1N4936GP- DIODE 1N4936GP (TAPPING) I301 PTB2SW8205 HEAT SINK ASS`Y 1TDA8172-- + 7174300811
D814 PTP2SW6900 HEAT SINK ASS`Y DFMLG12S-- + 7174301011 I301 1TDA8172-- IC V-OUT TDA8172 R
D815 DUZ5R6BM-- DIODE ZENER UZ-5.6BM(TAPPING) I301A 4857028205 HEAT SINK AL EX BK
D816 D1N4936GP- DIODE 1N4936GP (TAPPING) I301B 7174300811 SCREW TAPPTITE TT2 RND 3X8 MFZN
D817 D1N4148--- DIODE 1N4148 (TAPPING) I601 PTA2SW7534 HEAT SINK ASS`Y 1TDA7269-- + 7174300811
D818 DEU1Z----- DIODE EU1Z (HIGH SPEED) I601 1TDA7269-- IC AUDIO TDA7269 R
D819 DEU1Z----- DIODE EU1Z (HIGH SPEED) I601A 4857027534 HEAT SINK AL EXBK
D820 PTP2SW6900 HEAT SINK ASS`Y DFMLG12S-- + 7174301011 I601B 7174300811 SCREW TAPPTITE TT2 RND 3X8 MFZN
D822 D1N4936GP- DIODE 1N4936GP (TAPPING) I604 1DP3519AA2 IC AUDIO DOLBY DPL3519A-A2
D824 D1N4936GP- DIODE 1N4936GP (TAPPING) I605 1KA4558--- IC AMP KA4558
D825 D1N4936GP- DIODE 1N4936GP (TAPPING) I606 1MSP3410D- IC AUDIO MSP3410D
D904 DLT2A05G-- DIODE LT2A05G (TP) I701 1ST195EPM- IC MICOM OTP ST92T195B1/EPM R
D905 D1N4936GP- DIODE 1N4936GP (TAPPING) I702 1AT24C16PC IC AT24C16-10PC
DA01 DUZ5R6BM-- DIODE ZENER UZ-5.6BM(TAPPING) I703 1TS0P1238W IC PREAMP TS0P1238WI1
DA02 DUZ5R1B--- DIODE ZENER UZ-5.1B UNIZON I704 1K1A7042AP IC REGULATOR KIA7042AP
DA03 DUZ5R6BM-- DIODE ZENER UZ-5.6BM(TAPPING) I801 PTA2SW7910 HEAT SINK ASS`Y 1STRF6654- + 7171300811
DA04 DUZ5R6BM-- DIODE ZENER UZ-5.6BM(TAPPING) I801 1STRF6654- IC SMPS STR-F6654 R
DA05 DUZ5R6BM-- DIODE ZENER UZ-5.6BM(TAPPING) I801A 4857027910 HEAT SINK AL EX
DA07 DUZ5R6BM-- DIODE ZENER UZ-5.6BM(TAPPING) I801B 7174300811 SCREW TAPPTITE TT2 RND 3X8 MFZN
DA11 DUZ5R6BM-- DIODE ZENER UZ-5.6BM(TAPPING) I802 1LTV817C-- IC PHOTO COUPLER LTV-817C R
DA12 DUZ5R1B--- DIODE ZENER UZ-5.1B UNIZON I803 1SE140N--- IC AMP SE140N
DA13 DUZ5R1B--- DIODE ZENER UZ-5.1B UNIZON I804 1KA7805--- IC REGULATOR KA7805
DA15 DUZ5R6BM-- DIODE ZENER UZ-5.6BM(TAPPING) I805 PTA2SW7710 HEAT SINK ASS`Y 1PR05RF11- + 7174300811
DA16 DUZ5R1B--- DIODE ZENER UZ-5.1B UNIZON I805 1PQ05RF11- IC REGULATOR PQ05RF11
DA17 DUZ5R1B--- DIODE ZENER UZ-5.1B UNIZON I805A 4857027710 HEAT SINK AL EX
DA18 DUZ5R1B--- DIODE ZENER UZ-5.1B UNIZON I805B 7174300811 SCREW TAPPTITE TT2 RND 3X8 MFZN
DA19 DUZ5R1B--- DIODE ZENER UZ-5.1B UNIZON I807 1MC7812--- IC REGULATOR MC7812 12V 1A (KA7812)
38
I808 1KA7808--- IC REGULATOR KA7808 L610 58C0000116 COIL BEAD HC-3550R
I809 1UPC574J-- IC UPC574J L620 5CPX100K04 COIL PEAKING 10UH K ELC0607RA
I810 TX0202DA-- THYRISTOR X0202DA1BA2 L621 5CPX100K04 COIL PEAKING 10UH K ELC0607RA
I901 PTB2SW5403 HEAT SINK ASS`Y 1TEA5101B- + 7174300811 L625 5CPZ569K02 COIL PEAKING 5.6UH K (AXIAL 3.5MM)
I901 1TEA5101B- IC VIDEO AMP TEA5101B L626 5CPZ569K02 COIL PEAKING 5.6UH K (AXIAL 3.5MM)
I901A 4857025403 HEAT SINK AL050P-H24 T=2 L801 5MC0000100 COIL BEAD HC-3550
I901B 7174300811 SCREW TAPPTITE TT2 RND 3X8 MFZN L802 58C0000096 COIL CHOKE 610G0233(470K)
JC100 HRFT000-CA R CHIP 1/10 0 OHM 2012 L821 5PLF24A1-- FILTER LINE LF-24A1
JC101 HRFT000-CA R CHIP 1/10 0 OHM 2012 LA10 5MC0000100 COIL BEAD HC-3550
JC103 HRFT000-CA R CHIP 1/10 0 OHM 2012 LA20 5MC0000100 COIL BEAD HC-3550
JC107 HRFT000-CA R CHIP 1/10 0 OHM 2012 P101 485923162S CONN WAFER YW025-03 (STICK)
JC123 HRFT000-CA R CHIP 1/10 0 OHM 2012 P401A 4850704S04 CONNECTOR YH025-
JC306 HRFT000-CA R CHIP 1/10 0 OHM 2012 04+YST025+ULW=400
JC702 HRFT000-CA R CHIP 1/10 0 OHM 2012 P501A 4850707S02 CONNECTOR YH025-
JC704 HRFT000-CA R CHIP 1/10 0 OHM 2012 07+YST025+ULW=400
JC705 HRFT000-CA R CHIP 1/10 0 OHM 2012 P503 4859281320 CONN WAFER TAC-L18X-A1
JC706 HRFT000-CA R CHIP 1/10 0 OHM 2012 P504 4859281320 CONN WAFER TAC-L18X-A1
JC806 HRFT000-CA R CHIP 1/10 0 OHM 2012 P801 4859242220 CONN WAFER YFW800-02
JCA02 HRFT000-CA R CHIP 1/10 0 OHM 2012 P802 4859242220 CONN WAFER YFW800-02
JCA03 HRFT000-CA R CHIP 1/10 0 OHM 2012 P903 4859238620 CONN WAFER YPW500-02
JPA01 4859200401 SOCKET RGB YRS21-R1 PD03A 4850703S29 CONNECTOR YH025-
JPA02 4859200401 SOCKET RGB YRS21-R1 03+YST025+USW=300
JPA03 4859108450 JACK PIN BOARD YSC03P-4120-14A PWC1 PTWBSW7410 CORD POWER ASS`Y 906111+HOUS R
JPA05 4859100680 JACK AUDIO SI-T55220P 4P ING+TUBE+17700
TERMINAL Q101 TKTC3197-- TR KTC3197 (TP)
L101 5CPZ479K02 COIL PEAKING 4.7UH K (AXIAL 3.5MM) Q401 PTA3SW1000 HEAT SINK ASS`Y TBUH1015H1 + 7174300811
L103 5.80E+42 COIL AFT TRF-A005 Q401 TBUH1015H1 TR BUH1015HI
L301 5MC0000100 COIL BEAD HC-3550 Q401A 4857031000 HEAT SINK AL EX
L302 5CPZ479K02 COIL PEAKING 4.7UH K (AXIAL 3.5MM) Q401B 7174300811 SCREW TAPPTITE TT2 RND 3X8 MFZN
L303 5MC0000100 COIL BEAD HC-3550 Q402 TBD709---- TR BD709
L401 58H0000054 COIL H-LINEARITY TRL-040F Q403 PTQ2SW7800 HEAT SINK ASS`Y TKTD2058Y-+ 7174300811
L402 5MC0000100 COIL BEAD HC-3550 Q403 TKTD2058Y- TR KTD 2058-Y
L403 58C0000118 COIL CHOKE CH-191A Q403A 4857027800 HEAT SINK AL EX
L404 5MC0000100 COIL BEAD HC-3550 Q403B 7174300811 SCREW TAPPTITE TT2 RND 3X8 MFZN
L601 5CPZ109M02 COIL PEAKING 1UH M (AXIAL 3.5MM) QC101 T2SC2412KB TR CHIP 2SC2412K-T146-BR
L606 5CPZ479K02 COIL PEAKING 4.7UH K (AXIAL 3.5MM) QC104 T2SC2412KB TR CHIP 2SC2412K-T146-BR
L607 5CPZ479K02 COIL PEAKING 4.7UH K (AXIAL 3.5MM) QC107 T2SC2412KB TR CHIP 2SC2412K-T146-BR
L609 5MC0000100 COIL BEAD HC-3550 QC401 T2SC2412KB TR CHIP 2SC2412K-T146-BR
39
QC402 T2SC2412KB TR CHIP 2SC2412K-T146-BR R417 RF-4Y228K- R FUSIBLE 1/4 0.22 OHM K
QC405 T2SA812T2B TR CHIP 2SA812-T2B R418 RF01Z188K- R FUSIBLE 1W 0.18 OHM K (TAPPING)
QC501 T2SC2412KB TR CHIP 2SC2412K-T146-BR R420 RN02B473JS R METAL FILM 2W 47K OHM J SMALL
QC502 T2SC2412KB TR CHIP 2SC2412K-T146-BR R502 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
QC601 T2SC2412KB TR CHIP 2SC2412K-T146-BR R601 RD-4Z479J- R CARBON FILM 1/4 4.7 OHM J
QC602 T2SC2412KB TR CHIP 2SC2412K-T146-BR R602 RD-4Z479J- R CARBON FILM 1/4 4.7 OHM J
QC610 T2SC2412KB TR CHIP 2SC2412K-T146-BR R605 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
QC611 T2SA812T2B TR CHIP 2SA812-T2B R606 RD-AZ101J- R CARBON FILM 1/6 100 OHM J
QC801 T2SC2412KB TR CHIP 2SC2412K-T146-BR R704 RD-AZ472J- R CARBON FILM 1/6 4.7K OHM J
QC803 T2SC2412KB TR CHIP 2SC2412K-T146-BR R706 RD-AZ472J- R CARBON FILM 1/6 4.7K OHM J
QC806 T2SA812T2B TR CHIP 2SA812-T2B R713 RD-AZ622J- R CARBON FILM 1/6 6.2K OHM J
QC807 T2SA812T2B TR CHIP 2SA812-T2B R801 DEC140M290 POSISTOR ECPCC140M290
R101 RD-AZ750J- R CARBON FILM 1/6 75 OHM J R802 RS02Z683JS R M-OXIDE FILM 2W 68K OHM J SMALL
R102 RD-AZ472J- R CARBON FILM 1/6 4.7K OHM J R803 RC-2Z225KP R CARBON COMP 1/2 2.2M OHM K
R104 RN-AZ1502F R METAL FILM 1/6 15K OHM F R805 RD-2Z100J- R CARBON FILM 1/2 10 OHM J
R105 RN-AZ3600F R METAL FILM 1/6 360.0 OHM F R809 RF01Z158K- R FUSIBLE 1W 0.15 OHM K (TAPPING)
R106 RD-AZ682J- R CARBON FILM 1/6 6.8K OHM J R810 RD-4Z102J- R CARBON FILM 1/4 1K OHM J
R110 RD-AZ333J- R CARBON FILM 1/6 33K OHM J R811 RS01Z102J- R M-OXIDE FILM 1W 1K OHM J (TAPPING)
R111 RD-AZ183J- R CARBON FILM 1/6 18K OHM J R812 RD-AZ103J- R CARBON FILM 1/6 10K OHM J
R301 RN-AZ1202F R METAL FILM 1/6 12K OHM F R813 RD-AZ203J- R CARBON FILM 1/6 20K OHM J
R302 RD-2Z229J- R CARBON FILM 1/2 2.2 OHM J R815 RD-AZ102J- R CARBON FILM 1/6 1K OHM J
R303 RN-4Z2401F R METAL FILM 1/4 2.40K OHM F R816 RF02Z228K- R FUSIBLE 2W 0.22 OHM K (TAPPING)
R304 RN-AZ2201F R METAL FILM 1/6 2.2K OHM F R817 RF02Z228K- R FUSIBLE 2W 0.22 OHM K (TAPPING)
R305 RD-2Z151J- R CARBON FILM 1/2 150 OHM J R818 RC-2Z565KP R CARBON COMP 1/2 5.6M OHM K
R306 RW01Y228F- R WIRE WOUND 1W 0.22 OHM F R819 RX10T339J- R CEMENT 10W 3.3 OHM J TRIPOD
R307 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R820 RD-2Z222J- R CARBON FILM 1/2 2.2K OHM J
R308 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R822 RD-AZ202J- R CARBON FILM 1/6 2K OHM J
R401 RS02Z220JS R M-OXIDE FILM 2W 22 0HM J SMALL R823 RD-4Z153J- R CARBON FILM 1/4 15K OHM J
R403 RF01Z689J- R FUSIBLE 1W 6.8 OHM J (TAPPING) R824 RD-AZ332J- R CARBON FILM 1/6 3.3K OHM J
R404 RD-AZ472J- R CARBON FILM 1/6 4.7K OHM J R825 RS02Z100JS R M-OXIDE FILM 2W 10 OHM J SMALL
R405 RD-AZ472J- R CARBON FILM 1/6 4.7K OHM J R826 RS02Z103JS R M-OXIDE FILM 2W 10K OHM J SMALL
R406 RF01Z228K- R FUSIBLE 1W 0.22 OHM K (TAPPING) R827 RD-4Z102J- R CARBON FILM 1/4 1K OHM J
R407 RN-4Z2003F R METAL FILM 1/4 200K OHM F R828 RD-AZ102J- R CARBON FILM 1/6 1K OHM J
R408 RD-4Z479J- R CARBON FILM 1/4 4.7 OHM J R829 RD-AZ152J- R CARBON FILM 1/6 1.5K OHM J
R409 RD-4Z689J- R CARBON FILM 1/4 6.8 OHM J R830 RD-AZ102J- R CARBON FILM 1/6 1K OHM J
R411 RD-AZ220J- R CARBON FILM 1/6 22 OHM J R902 RD-AZ242J- R CARBON FILM 1/6 2.4K OHM J
R415 RS02Z561JS R M-OXIDE FILM 2W 560 OHM J SMALL R903 RS01Z683J- R M-OXIDE FILM 1W 68K OHM J (TAPPING)
R416 RF01Z188K- R FUSIBLE 1W 0.18 OHM K (TAPPING) R905 RC-2Z102K- R CARBON COMP 1/2 1K OHM K
40
R907 RD-AZ242J- R CARBON FILM 1/6 2.4K OHM J RC411 HRFT123JCA R CHIP 1/10 12K OHM J 2012
R908 RS01Z683J- R M-OXIDE FILM 1W 68K OHM J (TAPPING) RC412 HRFT101JCA R CHIP 1/10 100 OHM J 2012
R910 RC-2Z102K- R CARBON COMP 1/2 1K OHM K RC413 HRFT101JCA R CHIP 1/10 100 OHM J 2012
R912 RD-AZ242J- R CARBON FILM 1/6 2.4K OHM J RC414 HRFT152JCA R CHIP 1/10 1.5K OHM J 2012
R913 RS01Z683J- R M-OXIDE FILM 1W 68K OHM J (TAPPING) RC415 HRFT682JCA R CHIP 1/10 6.8K OHM J 2012
R915 RC-2Z102K- R CARBON COMP 1/2 1K OHM K RC544 HRFT102JCA R CHIP 1/10 1K OHM J 2012
R920 RD-2Z105J- R CARBON FILM 1/2 1M OHM J RC546 HRFT202JCA R CHIP 1/10 2K OHM J 2012
R921 RD-2Z102J- R CARBON FILM 1/2 1K OHM J RC603 HRFT512JCA R CHIP 1/10 5.1K OHM J 2012
RA02 RD-AZ750J- R CARBON FILM 1/6 75 OHM J RC604 HRFT512JCA R CHIP 1/10 5.1K OHM J 2012
RA03 RD-AZ750J- R CARBON FILM 1/6 75 OHM J RC605 HRFT303JCA R CHIP 1/10 30K OHM J 2012
RB02 RV5426103P R SEMI FIXED ENV-DJAA03B14 10K RC606 HRFT303JCA R CHIP 1/10 30K OHM J 2012
OHM B RC607 HRFT272JCA R CHIP 1/10 2.7K OHM J 2012
RC101 HRFT103JCA R CHIP 1/10 10K OHM J 2012 RC608 HRFT332JCA R CHIP 1/10 3.3K OHM J 2012
RC102 HRFT103JCA R CHIP 1/10 10K OHM J 2012 RC618 HRFT103JCA R CHIP 1/10 10K OHM J 2012
RC108 HRFT153JCA R CHIP 1/10 15K OHM J 2012 RC619 HRFT101JCA R CHIP 1/10 100 OHM J 2012
RC109 HRFT222JCA R CHIP 1/10 2.2K OHM J 2012 RC620 HRFT101JCA R CHIP 1/10 100 OHM J 2012
RC110 HRFT472JCA R CHIP 1/10 4.7K OHM J 2012 RC621 HRFT103JCA R CHIP 1/10 10K OHM J 2012
RC129 HRFT472JCA R CHIP 1/10 4.7K OHM J 2012 RC702 HRFT101JCA R CHIP 1/10 100 OHM J 2012
RC130 HRFT151JCA R CHIP 1/10 150 OHM J 2012 RC703 HRFT101JCA R CHIP 1/10 100 OHM J 2012
RC137 HRFT101JCA R CHIP 1/10 100 OHM J 2012 RC708 HRFT222JCA R CHIP 1/10 2.2K OHM J 2012
RC138 HRFT682JCA R CHIP 1/10 6.8K OHM J 2012 RC709 HRFT222JCA R CHIP 1/10 2.2K OHM J 2012
RC140 HRFT470JCA R CHIP 1/10 47 OHM J 2012 RC714 HRFT223JCA R CHIP 1/10 22K OHM J 2012
RC306 HRFT471JCA R CHIP 1/10 470 OHM J 2012 RC722 HRFT332JCA R CHIP 1/10 3.3K OHM J 2012
41
RC730 HRFT101JCA R CHIP 1/10 100 OHM J 2012 SW704 5S50101090 SW TACT SKHV17910A
RC731 HRFT161JCA R CHIP 1/10 160 OHM J 2012 SW801 5S40101143 SW POWER PUSH PS3-22SP (P.C.B) R
RC732 HRFT151JCA R CHIP 1/10 150 OHM J 2012 T401 50D25A1--- TRANS DRIVE TD-25A1
RC733 HRFT102JCA R CHIP 1/10 1K OHM J 2012 T402 50H0000200 FBT 1372.0036 R
RC734 HRFT102JCA R CHIP 1/10 1K OHM J 2012 T801 50M4936A9- TRANS SMPS TSM-4936A9
RC735 HRFT101JCA R CHIP 1/10 100 OHM J 2012 TU01 4859719430 TUNER VARACTOR EL2782/105-B R
RC802 HRFT103JCA R CHIP 1/10 10K OHM J 2012 W101 4851900130 GROUND TUNER AS DS-W1015-S
RC804 HRFT100JCA R CHIP 1/10 10 OHM J 2012 X601 5XE18R432E CRYSTAL QUARTZ HC-49/U 18.43200MHZ
RC901 HRFT821JCA R CHIP 1/10 820 OHM J 2012 30PPM
RC902 HRFT821JCA R CHIP 1/10 820 OHM J 2012 X701 5XEX4R000C CRYSTAL QUARTZ HC-49U 4.0000MHZ (TP)
RC903 HRFT821JCA R CHIP 1/10 820 OHM J 2012 Y801 5SC0101003 SW RELAY DG12D1-0(M)-II 1C-1P
RC904 HRFT751JCA R CHIP 1/10 750 OHM J 2012 Z101 5PMKT40MA- FILTER CERA MKT40MA100P
RC905 HRFT751JCA R CHIP 1/10 750 OHM J 2012 ZA01 5PXF1B471M FILTER EMI CFI 06 B 1H 470PF
RCA01 HRFT750JCA R CHIP 1/10 75 OHM J 2012 ZA09 5PXF1B471M FILTER EMI CFI 06 B 1H 470PF
RCA02 HRFT750JCA R CHIP 1/10 75 OHM J 2012 ZA10 5PXF1B471M FILTER EMI CFI 06 B 1H 470PF
RCA03 HRFT750JCA R CHIP 1/10 75 OHM J 2012 ZZ400 PTMAMSD228 PCB MAIN MODULE DTJ-28G6F R
RCA04 HRFT101JCA R CHIP 1/10 100 OHM J 2012 MANU
RCA05 HRFT101JCA R CHIP 1/10 100 OHM J 2012 PD01 4859279820 CONN WAFER TAC-L18P-A1 (ANGLE)
RCA06 HRFT101JCA R CHIP 1/10 100 OHM J 2012 PD02 4859279820 CONN WAFER TAC-L18P-A1 (ANGLE)
RCA07 HRFT103JCA R CHIP 1/10 10K OHM J 2012 PD03 4859231620 CONN WAFER YW025-03
RCA10 HRFT102JCA R CHIP 1/10 1K OHM J 2012 PD04 4853946000 BRKT JUMPER A SECC T1.0 (VCR-63DB)
RCA11 HRFT102JCA R CHIP 1/10 1K OHM J 2012 PD05 4853946000 BRKT JUMPER A SECC T1.0 (VCR-63DB)
RCA12 HRFT102JCA R CHIP 1/10 1K OHM J 2012 PS01 4850702N07 CONNECTOR YH500D-
RCA13 HRFT102JCA R CHIP 1/10 1K OHM J 2012 02+YBNH250+USW=400
RCA14 HRFT102JCA R CHIP 1/10 1K OHM J 2012 QS01 TKTA1659Y- TR KTA 1659-Y
RCA15 HRFT102JCA R CHIP 1/10 1K OHM J 2012 QS02 TKTC4370Y- TR KTC 4370-Y
RCA16 HRFT102JCA R CHIP 1/10 1K OHM J 2012 XD01 5XE20R250E CRYSTAL QUARTZ HC-49/U 20.2500MHZ
RCA17 HRFT102JCA R CHIP 1/10 1K OHM J 2012 30PPM
RCA26 HRFT473JCA R CHIP 1/10 47K OHM J 2012 CCD01 HCFK105ZCA C CHIP CERA 50V Y5V 1MF Z 2012
SCT1 4859302930 SOCKET CRT ISHS-09S CCD04 HCFK105ZCA C CHIP CERA 50V Y5V 1MF Z 2012
SF01 5PG3962M-- FILTER SAW G 3962-M CCD05 HCFK105ZCA C CHIP CERA 50V Y5V 1MF Z 2012
SF02 5PK9650M-- FILTER SAW K9650M CCD06 HCQK101JCA C CHIP CERA 50V CH 100PF J 2012
SW601 5S30202033 SW SLIDE KSA-2273S CCD07 HCQK121JCA C CHIP CERA 50V CH 120PF J 2012
SW700 5S50101090 SW TACT SKHV17910A CCD08 HCTAD100MB C CHIP TANTAL 10V 10MF M 3216
SW701 5S50101090 SW TACT SKHV17910A CCD09 HCQK309CCA C CHIP CERA 50V CH 3PF C 2012
SW702 5S50101090 SW TACT SKHV17910A CCD10 HCQK309CCA C CHIP CERA 50V CH 3PF C 2012
SW703 5S50101090 SW TACT SKHV17910A CCD11 HCFK105ZCA C CHIP CERA 50V Y5V 1MF Z 2012
42
CCD12 HCBK473KCA C CHIP CERA 50V X7R 0.047MF K 2012 JCD03 HRFT000-CA R CHIP 1/10 0 OHM 2012
CCD13 HCBH224KCA C CHIP CERA 25V X7R 0.22MF K 2012 JCD04 HRFT000-CA R CHIP 1/10 0 OHM 2012
CCD17 HCBK122KCA C CHIP CERA 50V X7R 1200PF K 2012 JCD08 HRFT000-CA R CHIP 1/10 0 OHM 2012
CCD20 HCTAD100MB C CHIP TANTAL 10V 10MF M 3216 JCD10 HRFT000-CA R CHIP 1/10 0 OHM 2012
CCD22 HCTAD100MB C CHIP TANTAL 10V 10MF M 3216 QCD01 TKTC3875GB TR CHIP KTC3875-GR
CCD23 HCBH104KCA C CHIP CERA 25V X7R 0.1MF K 2012 QCD50 TKTC3875GB TR CHIP KTC3875-GR
CCD25 HCBH104KCA C CHIP CERA 25V X7R 0.1MF K 2012 QCD52 TKTC3875GB TR CHIP KTC3875-GR
CCD27 HCFK105ZCA C CHIP CERA 50V Y5V 1MF Z 2012 QCD57 TKTC3875GB TR CHIP KTC3875-GR
CCD28 HCFK105ZCA C CHIP CERA 50V Y5V 1MF Z 2012 QCD58 T2SA812T2B TR CHIP 2SA812-T2B
CCD29 HCFK104ZCA C CHIP CERA 50V Y5V 0.1MF Z 2012 QCD59 T2SA812T2B TR CHIP 2SA812-T2B
CCD30 HCBH104KCA C CHIP CERA 25V X7R 0.1MF K 2012 QCD60 T2SA812T2B TR CHIP 2SA812-T2B
CCD31 HCQK101JCA C CHIP CERA 50V CH 100PF J 2012 QCD61 T2SA812T2B TR CHIP 2SA812-T2B
CCD32 HCQK101JCA C CHIP CERA 50V CH 100PF J 2012 QCS01 TKTC3875GB TR CHIP KTC3875-GR
CCD33 HCBK153KCA C CHIP CERA 50V X7R 0.015MF K 2012 QCS02 TKTC3875GB TR CHIP KTC3875-GR
CCD36 HCFK105ZCA C CHIP CERA 50V Y5V 1MF Z 2012 QCS05 TKTC3875GB TR CHIP KTC3875-GR
CCD37 HCQK101JCA C CHIP CERA 50V CH 100PF J 2012 QCS06 T2SA812T2B TR CHIP 2SA812-T2B
CCD38 HCFK105ZCA C CHIP CERA 50V Y5V 1MF Z 2012 QCS07 TKTC3875GB TR CHIP KTC3875-GR
CCD40 HCBH104KCA C CHIP CERA 25V X7R 0.1MF K 2012 QCS08 TKTC3875GB TR CHIP KTC3875-GR
CCD44 HCBH104KCA C CHIP CERA 25V X7R 0.1MF K 2012 RCD01 HRFT750JCA R CHIP 1/10 75 OHM J 2012
CCD45 HCFK105ZCA C CHIP CERA 50V Y5V 1MF Z 2012 RCD02 HRFT103JCA R CHIP 1/10 10K OHM J 2012
CCD53 HCBH104KCA C CHIP CERA 25V X7R 0.1MF K 2012 RCD08 HRFT103JCA R CHIP 1/10 10K OHM J 2012
CCS01 HCFK103ZCA C CHIP CERA 50V Y5V 0.01MF Z 2012 RCD09 HRFT101JCA R CHIP 1/10 100 OHM J 2012
CCS02 HCFK103ZCA C CHIP CERA 50V Y5V 0.01MF Z 2012 RCD10 HRFT101JCA R CHIP 1/10 100 OHM J 2012
CCS04 HCBK122KCA C CHIP CERA 50V X7R 1200PF K 2012 RCD14 HRFT101JCA R CHIP 1/10 100 OHM J 2012
CCS06 HCBK472KCA C CHIP CERA 50V X7R 4700PF K 2012 RCD15 HRFT271JCA R CHIP 1/10 270 OHM J 2012
CCS07 HCQK101JCA C CHIP CERA 50V CH 100PF J 2012 RCD16 HRFT162JCA R CHIP 1/10 1.6K OHM J 2012
CCS08 HCQK101JCA C CHIP CERA 50V CH 100PF J 2012 RCD17 HRFT363JCA R CHIP 1/10 36K OHM J 2012
JCD01 HRFT000-CA R CHIP 1/10 0 OHM 2012 RCD18 HRFT101JCA R CHIP 1/10 100 OHM J 2012
JCD02 HRFT000-CA R CHIP 1/10 0 OHM 2012 RCD19 HRFT750JCA R CHIP 1/10 75 OHM J 2012
43
RCD20 HRFT750JCA R CHIP 1/10 75 OHM J 2012 RCS24 HRFT122JCA R CHIP 1/10 1.2K OHM J 2012
RCD21 HRFT750JCA R CHIP 1/10 75 OHM J 2012 RCS25 HRFT152JCA R CHIP 1/10 1.5K OHM J 2012
RCD22 HRFT750JCA R CHIP 1/10 75 OHM J 2012 RCS27 HRFT229JCA R CHIP 1/10 2.2 OHM J 2012
RCD23 HRFT750JCA R CHIP 1/10 75 OHM J 2012 RCS28 HRFT123JCA R CHIP 1/10 12K OHM J 2012
RCD27 HRFT101JCA R CHIP 1/10 100 OHM J 2012 RCS29 HRFT100JCA R CHIP 1/10 10 OHM J 2012
RCD28 HRFT101JCA R CHIP 1/10 100 OHM J 2012 CD01 CEXD1E100F C ELECTRO 25V RND 10MF (5X11) TP
RCD31 HRFT101JCA R CHIP 1/10 100 OHM J 2012 CD04 CEXD1H339F C ELECTRO 50V RND 3.3MF (5X11) TP
RCD32 HRFT161JCA R CHIP 1/10 160 OHM J 2012 CS01 CEXF1C470V C ELECTRO 16V RSS 47MF (5X11) TP
RCD50 HRFT431JCA R CHIP 1/10 430 OHM J 2012 CS03 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP
RCD52 HRFT431JCA R CHIP 1/10 430 OHM J 2012 CS05 CEXE2A100C C ELECTRO 100V RU 10MF (8X11.5) TP
RCD53 HRFT431JCA R CHIP 1/10 430 OHM J 2012 CS06 CCXB2H472K C CERA 500V B 4700PF K
RCD54 HRFT101JCA R CHIP 1/10 100 OHM J 2012 (TAPPING)
RCD55 HRFT101JCA R CHIP 1/10 100 OHM J 2012 LD01 5CPX100K04 COIL PEAKING 10UH K ELC0607RA
RCD56 HRFT101JCA R CHIP 1/10 100 OHM J 2012 LS01 5MC0000100 COIL BEAD HC-3550
RCD57 HRFT101JCA R CHIP 1/10 100 OHM J 2012 LS02 5MC0000100 COIL BEAD HC-3550
RCD61 HRFT152JCA R CHIP 1/10 1.5K OHM J 2012 LS03 5MC0000100 COIL BEAD HC-3550
RCD62 HRFT151JCA R CHIP 1/10 150 OHM J 2012 RS01 RD-4Z200J- R CARBON FILM 1/4 20 OHM J
RCS01 HRFT223JCA R CHIP 1/10 22K OHM J 2012 ID01 1VPC3215CT IC CHIP VIDEO VPC3215C
RCS02 HRFT621JCA R CHIP 1/10 620 OHM J 2012 ID02 1C1P3250AT IC CHIP VIDEO CIP3250A
RCS03 HRFT471JCA R CHIP 1/10 470 OHM J 2012 ID03 1SDA9255EQ IC CHIP SDA9255E+
RCS04 HRFT273JCA R CHIP 1/10 27K OHM J 2012 ID04 1DDP3310BT IC CHIP DDP3310B
RCS05 HRFT333JCA R CHIP 1/10 33K OHM J 2012
RCS07 HRFT201JCA R CHIP 1/10 200 OHM J 2012
RCS10 HRFT182JCA R CHIP 1/10 1.8K OHM J 2012
RCS16 HRFT820JCA R CHIP 1/10 82 OHM J
RCS17 HRFT820JCA R CHIP 1/10 82 OHM J
RCS19 HRFT000-CA R CHIP 1/10 0 OHM 2012
44
17
1. DTJ-28A6F
14
15
45
17 CP-810 1 EU ROPE C HASSIS
16 A66ECY13X_26V CR T 1 GLASS
15 7128301412 SCREW TAPPIN G 2 SW RM BK

14 7122401612 SCREW TAPPIN G 9 SW RM BK
13 7122401011 SCREW TAPPIN G 8 SW RM
12 4858311110 SPEAKER 2 12W8OHMSP-58126F
8. Mechanical Exploded View
11 4856716000 SPRING 1 SW PA
10 4856215402 WASHER RU BBER 4 CR
9 4856015820 SCREW_CRT _F IX 4 SW RM+SK-5 YL
8 4855059501 DECO C TRL 1 PVC
7 4854856801 BUTT ON POWER 1 HIPS BK
6 4853535600 CLAMP CORD 1 PE
5 4852822401 DOOR 1 PC
4 4852540601 GRILL L 1 PS T0.5
3 4852538401 GRILL R 1 PS T0.5
2 4852156501 COVER BACK 1 HIPS BK
1 4852074501 MASK FRONT 1 HIPS BK
4 11 7 5 8 1 3 12 13 16 10 9 NO PAR T C ODE PART N AM E QTY MATERIAL R EM ARKS

2. DTJ-28A7F
14
13
18
46
19 CP-810 1 EUROPE CHASSIS
18 4858311110 SPEAKER 2 12W8OHM SP-58126F
17 4852540300 GRILL L 1 PS T0.45
16 4852540200 GRILL R 1 PS T0.45
7 15 A66ECY13X_26V CRT GLASS
8
14 7128301212 SCREW TAPPING 1 SWRM BK
11 9 13 7122401612 SCREW TAPPING 10 SWRM BK
12 15
11 4857923300 DOOR LOCK 1 POM+N6+N66(G30)
10 4856716000 SPRING 1 SWPA
9 4856215402 WASHER RUBBER 4 CR T2.0
8 4856015820 SCREW_CRT_FIX 4 SWRM+SK-5 L=35
7 4855617401 MARK BRAND 1 A1050P-H24
6 4855059700 DECO CTRL 1 PVC T0.25
5 4854856701 BUTTON POWER 1 HIPS BK
1
4 4853526600 HOLDER CORD 1 NYLON66
3 4852822300 DOOR 1 PC SMOG
1 4852074301 MASK FRONT 1 HIPS BK
NO PART CODE PART NAME QTY MATERIAL REMARKS

16 5 10 3 6 17
Mechanical Exploded View
30 31 32 33
3. DTJ-28B1F
8 9 10
1 2 3 4 5 6 7
33 97 P 46 0 27 0 0 C L AM P C OR D 1 N Y LO N 6 6 BL K 5 2 80 N
32 48 5 5 41 5 80 0 S PEC P LA TE 1 1 5 0 AR T P/E FIL M (C /TV)
31 71 7 2 40 1 61 2 S CR E W TAP PTITE 1 0 T T2 TR S 4 X 16 M FZN B K 1 +30
C OV ER BA CK H IP S GY
47
30 48 5 2 15 7 00 1 1
29 71 7 4 30 0 81 1 S CR E W TAP PTITE 1 T T2 R N D 3X 8 M FZN
28 48 5 7 02 4 50 0 H EA T SIN K 1 A L EX B /K
26 48 5 7 02 4 60 0 H EA T SIN K 1 A L EX B /K
24 48 5 7 03 1 10 0 H EA T SIN K 1 A 1 05 0 P- H2 4 T2.0
20 22 24 26 28
22 48 5 7 02 4 42 2 H EA T SIN K 1 A L EX
19 21 23 25 27 29 21 71 7 4 30 1 01 1 S CR E W TAP PTITE 2 T T2 R N D 3X 10 M FZN
20 48 5 7 02 4 42 2 H EA T SIN K 1 A L EX
19 48 5 7 41 5 00 1 C L IP FU SE 2 P FC 5 00 0 -0 70 2
18 71 2 8 30 1 01 1 S CR E W TAP PIN G 1 T 2S WAS 3X 1 0 M FZN 1 7 +30
17 C H AS SIS 1 C P -8 10
16 48 5 3 53 3 60 0 H OL D ER L ED 1 P .P B K
15 48 5 2 54 1 00 0 GR IL L S PK R R 1 PS
14 48 5 5 61 7 40 1 M AR K B R AN D 1 A L (SIL VE R )
13 48 5 6 71 6 00 0 S PR IN G 1 S WP A P IE 0.5
12 48 5 4 85 7 20 1 B UTT ON P OWE R 1 A BS GY
11 48 5 2 54 0 90 0 GR IL L S PK R L 1 PS
10 CRT 1 P H ILIP S 2 8"
9 48 5 6 01 5 82 0 S CR E W C RT F IX 4 S WR M +SK5 L =35 1 +1 0
8 48 5 6 21 5 40 2 WA SH E R R U BB ER 4 C R T2 .0
16 17 18 7 48 5 4 94 6 60 1 B UTT ON C H 1 A BS GY
6 71 2 8 30 1 01 1 S CR E W TAP PIN G 2 T 2S WAS 3X 1 0 M FZN 1 +7
5 71 2 8 30 1 01 1 S CR E W TAP PIN G 1 T 2S WAS 3X 1 0 M FZN 1 +4
4 48 5 5 54 1 70 0 D EC O S EN SO R 1 P M MA
3 71 7 2 40 1 21 2 S CR E W TAP PTITE 8 T T2 TR S 4 X 12 M FZN CK 1 +2
12 13 14 15 2 48 5 8 31 1 11 0 S PEA KE R 2 1 2 W 8 OH M S P-5 8 12 6 F
1 48 5 2 07 5 00 1 M ASK FR ON T 1 H IP S GY
No P AR T C OD E P AR T N AM E Q'ty M AT ER IAL R EM AR K S
4. DTJ-28G6F
18
15 17
14
13
16
48
20
19
18 712 2401612 SCREW TAPPING 10 SWRM BK
17 485 2151900 COVER BACK 1 HIPS BK
16 4857817611 CLOTH BLACK 2 FELT T0.7 L=200
15 485 6015800 SCREW_CRT_FIX 4 SWRM+SK-5 BK
14 A66ECY13X_26V CRT A'ssy 1 GLASS
13 485 6215402 WASHER RUBBER 4 CR
12 12 PCB A'ssy 1 cp-775
11 4857818702 CLOTH BLACK 2 FELT T0.7 L=250 W=1 5
11
1 9 SPEA KER 2
10
7 4854939901 BUTTON CTRL 1 ABS BK
9
2 8 6 4855059001 DECO_CRTL 1 PS
5 485 2821501 DOOR 1 PC
3 7 4 4855617400 MARK BRAND 1 A1050P-H24
3 485 4854001 BUTTON_P OWER 1 ABS
4
2 4856716001 SPRING 1 SWPA
6 1 485206 7901 MASK FRONT 1 HIPS BK
5 NO P ART CODE PART NAME QTY MATERIAL REMARKS
5. DTJ-28G7F
49
6. DTJ-28G8F
21
16 20
15
14
19
50
18
22 23 4852539301 GRILL SPKR R 1 PS SHEET
22 4852539201 GRILL SPKR L 1 PS SHEET
17 21 7122401612 SCREW TAPPING 8 T2S TRS 4X16 MFZN BK
19 4857817610 CLOTH BLACK 3 FELT 300X20X0.7

17 4853951200 BKRT 4 EGI T1.0+CLOTH BLACK
16 4856015800 SCREW CRT FIX 4 L=27mm

15 A66EAK071X11 CRT A’ss 1 GLASS
14 4856215402 WASHER RUBBER 4 CR T2.0

13 PCB A’ss 1 cp-776
12 4857818701 CLOTH BLACK 2 FELT T0.7 L=350 W=15
13
11 4857818702 CLOTH BLACK 2 FELT T0.7 L=250 W=15
9 SPEAKER 2
1 8 7121301212 SCREW TAPPING 2 T2S WAS 3X12 MFZN BK
10 7 4854944500 BUTTON CTRL 1 ABS BK
3 6 4855540400 DECO SENSOR 1 PMMA CL

6
23 5 48556161SD MARK BRAND 1 SILVER DIA-CUTTING
9
8 4 4854855900 BUTTON POWER 1 HIPS BK
4
3 4852326101 SPRING 1 SWPA PIE0.5
2 4852326101 PANEL CONTROL 1 HIPS BK

5 7 1 4852073001 MASK FRONT 1 HIPS BK
NO PART CODE PART NAME QTY MATERIAL REMARKS

2
10. Printed Circuit Board
51
DAEWOO ELECTRONICS CO., LTD
686, AHYEON-DONG MAPO-GU
SEOUL, KOREA
C.P.O. BOX 8003 SEOUL, KOREA
TELEX : DWELEC K28177-8
CABLE : “DAEWOOELEC”
E-mail : leesk@web.dwe.co.kr
//
FAX : 82-2-360-7802
TEL : 82-2-360-7877

Daewoo TV CP810 Service Manual

Uploaded by

Copyright:

Available Formats

Daewoo TV CP810 Service Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Daewoo TV CP810 Service Manual

Uploaded by

Copyright:

Available Formats

S/M No: CP810P-010

MODEL : DTJ - 28A6F

DAEWOO ELECTRONICS CO., LTD.

X-RAY RADIATION PRECAUTION

PRODUCT SAFETY NOTICE

CRT 28" : A66EAK071X54 ( PHILIPS )

System PAL/SECAM-B/G, D/K, PAL-I/I’, SECAM-L/L’, NTSC-3.58/4.43 (Play back )

Main Voltage 230V AC, 50Hz

Power Consumption Stand-by mode : 2.0 Watts

Sound output 10 + 10 Watts, 10% THD at RF 60% mod. ( 1 kHz )

Speaker 12W 8ohm x 2 EA

Antenna Impedance 75 ohm unbalanced input (Din Standard )

Tuning system Frequency Synthesize(FS) Tuning System

Tuner DT5-BF14D, EL2782-105-B

Number of Program 100 programs

Aux. Terminal 21 pin EURO-SCART jack ( AV input, TV output, RGB input )

Remote controller R-22D05 with 2 "AAA" type batteries

Teletext TOP(5 Page memory) & FLOF(7 Page memory)

PIN Signal Designation Matching Value

* How to Enter the “ Service Mode ” with user remocon.

- You can see the SVC Menu by OSD in TV set.

4-4. SCREEN (G2)

4-6-2 VERTICAL CENTER

4-6-3 VERTICAL SIZE

4-6-4 VERTICAL S-CORRECTION ( Fixed : Adjust if need be )

4-6-5 HORIZONTAL CENTER

4-7-3 CORNER ( Fixed : Adjust if need be )

4-7-4 SYMMETRY ( Fixed : Adjust if need be )

4-8. WHITE BALANCE

4-9. SUB BRIGHT

4-10. DOUBLE TEXT CENTER

4-10-2 Select Menu

1.1.9 PWM Output - Rounding, fringe, double width, double height,

(3) Block Diagram

(4) PIN DESCRIPTION

Figure 2. Pin Description

5-2. VPS 3215C(Video Processor)

(3) Block Diagram

(4) Pin Descriptions

Pin 12 - Vertical Sync Pulse, VS Pin 52 - VGAV-Input.

5-3. CIP3250A (Component Interface Processor)

(3) Block Diagram

Pin 56 - TMODE Input Pin 63 - BU Analog Blue/U Chroma Input

Pin 65 - GY Analog Green/Luma Input

Pin 66 - GNDGY Analog Ground

Pin 67 - RV Analog Red/V Chroma Input

Pin 68 - GNDRY Analog Ground

5-4. SDA9255 (Scan Rate Converter )

• 100/120 Hz interlaced scan conbersion

(2) General Description

Reduction) and can therefore be used as a low cost digital featurebox.

(3) Block Diagram

(4) Pin Description

Pin No. Name Type Description

S : supply, I : input, O : output, TTL : digital (TTL)

5-5. DDP 3310B (Display and Deflection Processor)

(2) Feature Miscellaneous

(3) Block Diagram

Pin 62 - Line-Locked Clock Input LLC1 * Application Note :

Pin 64 - Sync Signal Input VS