COLOR TELEVISION

SERVICE MANUAL
21” T2S08 CHASSIS
WITH NICAM&TELETEXT

CONTENTS

ⅠSAFETY PRECAUTION ………………………………………………… 1

ⅡSPECIFICATION ………………………………………………………… 2
Ⅲ IC’S GENERAL DESCRIPTION ……………………………………… 3
Ⅳ SPECIAL IC INTRODUCTION ………………………………………… 3
Ⅴ CHASSIS BLOCK DIAGRAM ………………………………………… 12
Ⅵ SERVICE MODE&ADJUSTMENT …………………………………… 13
Ⅶ TEST POINT WAVE FORM&SCHEMATIC DIAGRAM …………… 18

-1-
ⅠSAFETY PRECAUTION
1. X-RAY RADIATION PRECAUTION
1.1 Excessive high voltage can produce potentially hazardous X-RAY RADIATION. To avoid such hazards
the high voltage must be specified limit. The normal value of the high voltage of this receiver is 27KV±
500V under 230V AC power source. The high voltage must not exceed 30KV.
1.2 Each time a receiver requires servicing the high voltage should be checked following the HIGH
VOLTAGE CHECK procedure in this manual. It is recommended the reading of the high voltage be
recorded as a part of the service record. It is important to use an accurate and reliable high voltage meter.
1.3 The primary source of X -RAY RADIATION in this TV receiver is the picture tube. For continued X-RAY
RADIATION protection, the replacement tube must be exactly the same type tube as used in this TV
receiver.
1.4 Some parts in this receiver have special safety-related characteristics for X-RAY RADIATION protection.
For continued safety, parts replacement should be undertaken only after referring the PRODUCT SAFETY
NOTICE below.

2. GENERAL SAFETY PRECAUTION

The following are the necessary precautions to be observed before servicing this chassis
WARNING: Service should not be attempted by anyone unfamiliar with the necessary
2.1 Since the power supply circuit of this receiver is directly connected to the AC power line. An isolation
transformer should be used during any dynamic service to avoid possible shock hazard.
2.2 Always discharge the picture tube anode to the CRT conductive coating before handling the picture
tube. The picture tube is highly evacuated and if broken, glass fragments will be violently expelled. Use
shatterproof goggles and keep picture tube away from the unprotected body while handling.
2.3 When replacing a chassis in the cabinet, always be certain that all the protective devices are put back
in place, such as: nonmetallic control; knobs, insulating covers, shields, isolation resistor-capacitor,
network, etc.
2.4 Connection wires must be kept away from components with high voltage or high temperature.
2.5 When replacing parts or circuit boards, disconnect the power cord.
2.6 When replacing a high voltage resistor (metal oxide resistor) on circuit board, keep the resistor APP.
10mm (1/2 in.) away from circuit board.
2.7 If any fuse in this TV receiver is broken, replace it with the FUSE specified in the chassis parts list.
2.8 The receiver is designed to operate with 230V (50Hz) AC mains.

3. PRODUCT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety-related characteristics are often
passed unnoticed by a visual inspection and the X-RAY RADIATON protection afforded by them cannot
necessarily be obtained by using replacement components rated for higher voltage. The use of substitute
replacement parts that do not have the same safety characteristics as specified in the parts list may create
shock, fire, X-RAY RADIATION or other hazards.

Warning!
There are no any repairable components in this TV set. Do not try to make any change to it. High voltage
inside may cause danger.

-1-
ⅡSPECIFICATION
COLOR SYSTEM: PAL SECAM
RF SYSTEM
SOUND SYSTEM:B/G D/K I NICAM STEREO
VIDEO SYSTEM PAL SECAM NTSC4.43
TUNING SYSTEM VOLTAGE SYNTHESIZER TUNING
VHF-L: E2～S6 48.25 MHz～140.25MHz
RECEIVING CHANNEL VHF-H: S7～S36 147.25 MHz～423.25MHz
UHF: S37～DS57 431.25 MHz～863.25MHz
PROGRAM PRESET 99
1 SIDE RCA AV IN
AV JACKS
1 FULL SCART AND 1 AV SCART
TELETEXT 1PAGE
ANTENNA INPUT 75Ω（UNBALANCE）
AUDIO OUTPUT ≥2.5W
MAIN POWER 170-260V AC 50/60Hz
POWER CONSUMPTION 100W

ⅢCHIP GENERAL DESCRIPTION

1. MAIN BOARD PART
IC001 ST92195 MCU With ON SCREEN DISPLAY and TELETEXT Decoder
IC002 24C08 8 Kbit Serial I2C Bus EEPROM
IC101 STV2246 I²C BUS-Controlled Multistandard Single Chip TV Processor
IC301 STV9306A/B BUS-Controlled VERTICAL DEFLECTION W.E/W CORRECTION CIRCUIT
IC601 H11A817C OPTOCOUPLERS
IC603 MC7808CT +8V VOLTAGE REGULATOR
IC604
MC7805CT +5V VOLTAGE REGULATOR
IC605
IC606 MC7812CT +12V VOLTAGE REGULATOR
IC701 CD7522CS 3W AUDIO AMPLIFIER
IC801 STV8216 Multi-standard TV Audio Processor and Digital Sound Demodulator

ⅣCHIP INTRODUCTION
1. ST92195
The ST92195 microcontrollers are developed and manufactured by STMicroelectronics using a proprietary
n-well HCMOS process. Their performance derives from the use of flexible 256-register programming model
for ultra-fast context switching and real-time event response. The intelligent on-chip peripherals offload the
ST9 core from I/O and data management processing tasks allowing critical application tasks to get the
maximum use of core resources. TheST92195 MCU support low power consumption and low voltage
operation for power-efficient and low-cost embedded systems.
1.1 Main features
28 fully-programmable I/Os
4 channels Analog/Digital Converter

-2-
Built in I2C bus interface
Built in OSD and Teletext decoder
14-bit Voltage Synthesis PWM output for VS tuning system

1.2 Pin description

Pin No. Pin Name Signal Name I/O Function
1 P2.0 IRIN I IR Input
2 RESET RESET I Hardware Reset
3 P0.7 NC I/O Not Used
4 P0.6 MUTE O Mute Output PIN
5 P0.5 NC I/O Not Used
6 P0.4 ON/OFF O Standby Output
7 P0.3 DESIGN I Service menu control
8 P0.2 SCART1 I Identify scart entering Design
9 P0.1 SCART2 I Identify scart entering Design
10 P0.0 AV SEL O AV Selection
11 P3.7 S0 O AV/TV
12 P3.6 S1 O AV/TV
13 P3.5 TV/DVD O TV/DVD
14 P3.4 DFD O Default data control
15 B B O OSD Blue colour Signal Output
16 G G O OSD Green colour Signal Output
17 R R O OSD Red colour Signal Output
18 BLANK BLANK O OSD Blanking Output
19 P5.1 SDA I/O I2C data line
20 P5.0 SCL O I2C clock line
21 VDD VDD +5 V Digital Supply
22 JTDO JTDO Test Pin
23 WSCF WSCF Analog Pin For VPS / WPP slicer line PLL
24 WSCR WSCR Analog Pin For VPS / WPP slicer line PLL
25 AVDD3 AVDD3 +5V Analog VDD For PLL
26 TEST0 TEST0 Test Pin
27 MCFM MCFM Analog Pin for display pixel freq. multiplier
28 JTCK JTCK Test Pin
29 TXCF TXCF Analog pin for VPS /WSS line PLL
30 CVBSO CVBSO Test Pin
31 AVDD2 AVDD2 Analog Power supply
32 JTMS JTMS Test Pin
33 CVBS2 CVBS2 I CVBS In for VPS / WSS
34 CVBS1 CVBS1 I CVBS In for Teletext Slicer
35 AGND AGND Analog ground
36 GND GND Digital ground
37 JTRST0 JTRST0 Test Pin
38 PXFM PXFM Analog Pin for display pixel freq. multiplier
39 AVDD1 AVDD1 Analog Power Supply
40 HSYNC HSYNC I Horizontal Sync Input
41 VSYNC VSYNC I Vertical Sync Input

-3-
 42 P4.0 BSW1 O Band switch 1
43 P4.1 BSW2 O Band switch 2
44 P4.2 SAW_SW1 O SAW Filter switch 1
45 P4.3 NC I/O Not connected
46 P4.4 SAW_SW2 O SAW Filter switch 2
47 P4.5 NC I/O Not connected
48 P4.6 Vlin PWM O V-linearity PWM output
49 P4.7 VOL PWM O VOL PWM output
50 XTAL XTAL Clock oscillator
51 XTAL XTAL Clock oscillator
52 P2.5 LED2 O LED driver
53 P2.4 LED1 O LED driver
54 P2.3 VS O VST Voltage ouput
55 P2.2 NC I/O Not connected
56 P2.1 KB INPUT I KEY Input

1.3 Block diagram

-4-
1.4 General application description
BAND SWITCH OUTPUT (Pin42 Pin43)
Pin42 BSW1 Pin43 BSW2 SELECTED BAND
0 0 NOT USED
0 1 VHF-L
1 0 VHF-H
1 1 UHF
KEYBOARD INPUT LEVEL (Pin56)
KEY IN (Pin 56) KEY PRESSED
0.285 ~ 0.587V Volume – (1 K ohm)
0.706 ~ 1.098V Volume + (2.2 K ohm)
1.204~ 1.596V Program- (3.9 K ohm)
1.704 ~ 2.096V Program+ (6.2 K ohm)
2.194 ~ 2.586V MENU (9.1 Kohm)
2.704 ~ 3.096V TV/DVD (13.8 Kohm)
3.205 ~ 3.606V AV/TV(22 Kohm)
3.745 ~ 4.145V Analog (37.4 Kohm)
4.282 ~ 4.682V OK (86.5 K ohm)
Note:The pull up resistor of Pin56 is 10K.
TV/AV SELECTION (Pin11/Pin12)
S0-Pin11 0 1 0 1
S1-Pin12 0 0 1 1
TV/AV MODE TV AV1/RGB AV2 S-VHS
STANDBY OUTPUT (Pin6)
STD-BY (Pin 6) Mode
0 Standby
1 Operating

2. STV2246H
The STV224XH is fully bus-controlled IC for TV that include PIF, SIF, Luma, Chroma and Deflection
processing functions. Used with a vertical frame booster (TDA8174A for a 90° chassis, STV9306 for a 110°
chassis), they allow multi-standard (BG/DK/I/MN/LL’, PAL/SECAM/NTSC) sets to be designed with very few
external components and no manual adjustments.

2.1 Main features

I²C Bus Control
PIF Circuit with PLL Demodulation (Positive and Negative Video)
SIF Circuit with QSS Structure, FM Demodulation and AM Demodulation for France
Intercarrier Capability and Built-in Sound Band pass
Sound Subcarrier Output for Stereo Chassis (FM, NICAM)
Integrated Chroma Filters and Luma Delay Line and Integrated Chroma Delay Line
3 channels input Video Switch and 2 channels CVBS output
OSD RGB Inputs and external RGB Inputs Interface
PAL/SECAM/NTSC Chroma Demodulators
Black Stretch and peaking Circuit

-5-
Automatic Cut-off Current Loop, manual Cut-off possible for low-cost applications
Two Horizontal Deflection PLLs
APR (Automatic RGB Peak Regulation) or RGB Peak Limitation Function

2.2 Pin description

PIN NO. SYMBOL DESCRIPTION
1 SIFIN1 SIF input
2 SIFIN2 SIF input
3 AGCSIFCAP AGC SIF capacitor
4 VREFIF Voltage reference filter
5 AGCPIFCAP AGC PIF capacitor
6 PIFIN1 PIF input
7 PININ2 PIF input
8 TUNERAGCOUT AGC Tuner output
9 IFPLL IF PLL filter
10 GNDIF IF Ground
11 AM/FMOUT/SC AM/FM Mono sound or stereo carriers output
12 VCCIF 5V IF Supply
13 INTCVBSOUT Internal CVBS output
14 EXTAUDIOIN External audio input
15 PIFLC1 LC input
16 PIFLC2 LC input
17 VCC2 Video/LUMA Supply voltage (8V)
18 CVBSIN1 Internal video input
19 GND2 Video/LUMA ground
20 CVBSIN2 External video input
21 BS Black stretch capacitor
22 Y/CVBSIN3 Y(SVHS) or CVBS3 external input
23 CHR Chroma(SVHS) input
24 APR Automatic RGB peak regulation
25 BEXT/Cb External blue input or Cb input
26 GEXT/Y External green input or Y input
27 REXT/Cr External red input or Cr input
28 FBEXT External fast blanking input
29 NC/CVBSOUT1 Not connected or CVBS output1
30 BOUT Blue output
31 GOUT Green output
32 ROUT Red output
33 ICATH Cathode current measurement input
34 BOSD OSD Blue input
35 GOSD OSD Green input
36 ROSD OSD Red input
37 FBOSD/HC OSD Fast blanking input/half contrast
38 XTAL3/BTUN 3.5x MHz Crystal or bell filter tuning capacitor
39 XTAL2 3.5x MHz Crystal
40 XTAL1 4.43/3.5x MHz Crystal

-6-
 41 CLPF Chroma PLL filter
XTAL1 control pin, vertical amplitude DAC output and chroma
42 X1/VAMP/CHROUT
reference signal output
43 GND1 Chroma/scanning ground
44 CVBSOUT2 Second video switch output
45 VCC1 Chroma/scanning power supply (8V)
46 BCL/SAF Beam current limiter control voltage and safety input(X-ray)
47 VERT Vertical output pulse
48 HOUT Horizontal output pulse
49 LFB/SSC Line flyback input and super-sandcastle output
50 SLPF Scanning PLL filter
51 SCL I2C Bus clock input
52 SDA I2C Bus data input
53 VCCD Digital supply voltage(5V)
54 GNDD Digital ground
55 AUDIOOUT Main audio output
56 FMCAP FM demodulation capacitor

2.3 Block diagram

3. STV9306A
The STV9306 is a fully I2C controlled vertical deflection IC designed forusein110°, 4/3 or 16/9 CRT
applications. It integrates both the vertical deflection and E/W correction circuitries necessary in design of a
110° chassis.

-7-
3.1 Main features
Fully I2C controlled
Internal flyback generator (UPTO60V) and DC Coupled operation
Self adapted sawtooth (50/60Hz)
Vertical linearity, amplitude and centering adjustments.
Horizontal width, pincushion, trapezoid and corner adjustments. Breathing correction.

3.2 Pin description

PIN NO. SYMBOL DESCRIPTION
2
1 SCL I C Bus clock
2 CRAMP Ramp capacitor
3 SDA I2C Bus data
4 CHOLD Hold capacitor
5 SYNC Sync input
6 VS Supply voltage
7 FLYBACK Flyback output
8 GND Vertical output
9 OUT Vertical output
10 VOPS Vertical output Power Supply
11 EWOUT EW output
12 SENS2 Vertical current sense2
13 EWFB EW feedback
14 SENS1 Vertical current sense1
15 BREATHING Breathing input

3.3 Block diagram

-8-
4. CD7522CS
The CD7522CS is a stereo 2×3W BTL audio amplifier, specially designed for high quality sound TV
applications. Features of the CD7522CS include Stand-by and Volume control functions.

4.1 Main feature

2×3W output power RL = 8Ω @THD = 0.5% VCC = 10V
Standby and volume control function
Low turn-on turn-off pop noise
Low voltage supply ≤ 14V
Thermal overload protection

4.2 Pin description

Pin NO. SYMBOL DESCRIPTION
1 VCC Power supply
2 OUT1+ Ch1 output +
3 GND Gnd (output ch1)
4 OUT1- Ch1 output -
5 ST-BY Standby control
6 Ch1 In Ch1 audio output
7 GND Gnd (Input)
8 Ch2 In Ch2 audio output
9 Vol DC volume control
10 OUT2- Ch2 output -
11 GND Gnd (output ch2)
12 OUT2+ Ch2 output +

4.3 Block diagram

-9-
5. STV8216
This chip included three main parts:
TV Sound Demodulator: provides all the necessary circuitry for the demodulation of audio transmissions of
European and Asian terrestrial TV broadcasts. The various transmission standards are automatically
detected and demodulated without user intervention.
Audio Processor: based on DSP technology independently controls loudspeaker, subwoofer and
headphone signals. It offers basic and advanced features, such as a ST Wide Surround, Equalizer, Automatic
Loudness and Smart Volume Control for television viewer comfort. The STV8226/36 versions can perform
additionally the SRS 3D Surround for stereo and mono signals.
Audio Matrix: 3 stereo and 1 mono external analog audio inputs to loudspeakers and headphone, with 2
stereo external analog audio outputs (SCART compatible).

5.1 Main features

NICAM, AM, FM Mono and FM 2 carrier stereo demodulators for all sound carriers between 4.5 and 7MHz
Mono input provided for optimum AM demodulation performances
Demodulation controlled by automatic standard recognition system
Sound IF AGC with wide range, over modulation and carrier offset recovery,
Smart volume control, smart volume control, 5-band equalizer bass/treble control, automatic loudness control
Loudspeaker and Headphone outputs with volume/balance controls and beeper
Subwoofer output with volume control and programmable bandwidth, spatial Sound Effects (ST Wide
Surround and Pseudo-Stereo), low-noise audio mutes and switches
I²C Bus-controlled, single and standard 27 MHz crystal oscillator,
Power supplies: 3.3V Digital, 5V or 8V Analog, embedded 3.3V regulators

5.2 Pin description

Pin NO. SYMBOL Pin TYPE DESCRIPTION
1 SIF Analog Sound IF input
2 VTOP Analog ADC VTOP decoupling pin
3 VREF IF Analog AGC Voltage reference decoupling Pin
4 VDDIF Analog power supply 3.3V Power supply for IF AGC & ADC
5 GNDIF Analog power supply Ground for IF AGC & ADC
6 MONOIN Analog Mono Input
7 AO1L Analog Left SCART1 audio output
8 AO1R Analog Right SCART1 audio output
9 VDDC Analog power supply 3.3V Power supply for audio DAC/ADC
10 GNDC Analog power supply Ground for audio DAC/ADC
11 AI1L Analog Left SCART1 audio input
12 AI1R Analog Right SCART1 audio input
13 VMC1 Analog Switched VREF decoupling Pin for audio converters (VMCP)
14 VMC2 Analog VREF decoupling Pin for audio converters (VMC)
15 AI2L Analog Left SCART2 audio input
16 AI2R Analog Right SCART2 audio input
17 VDDA Analog power supply 3.3 V power supply for audio buffers, matrix & bias
18 GNDAH Analog power supply Ground for audio buffers and SCART
19 AO2L Analog Left SCART2 Audio output
-10-
 20 AO2R Analog Right SCART2 Audio output
21 VDDH Analog power supply 8V/5V power supply for SCART and audio buffers
22 VREFA Analog Voltage reference for audio buffers
23 AI3L Analog Left SCART3 audio input
24 AI3R Analog Right SCART3 audio input
25 BGAP Analog Bandgap voltage source decoupling
26 LSL Analog Left loudspeaker output
27 LSR Analog Right loudspeaker output
28 SW Analog Subwoofer output
29 HPL Analog Left headphone output
30 HPR Analog Right headphone output
31 GNDSA Analog power supply Substrate analog/digital shield
32 HPD Bidirectional Headphone detection input (active low)
33 ADR Input Hardware I²C chip address control
34 SCL Open drain I²C serial clock
35 SDA Open drain I²C serial data
36 REG Analog 5V power regulator control
37 RESET Input Hardware reset (active low)
38 SYSCK Bidirectional System clock output
39 MCK Bidirectional I²S master clock output
40 VDD1 Digital power supply 3.3V Power supply for digital core & IO cells
41 GND1 Digital power supply Ground for digital core & IO cells
42 GNDSP Analog power supply Substrate analog/digital shield for clock-PLL
43 XTI Input Crystal oscillator Input
44 XTO Output Crystal oscillator output
45 VDDP Analog power supply 3.3V power supply for analog PLL clock
46 GNDP Analog power supply Ground for analog PLL clock
47 GND2 Digital power supply Ground for digital core, DSPs & IO cells
48 VDD2 Digital power supply 3.3V power supply for digital core, DSPs & IO cells
49 CKTST Input Must be connected to ground
50 SDO Bidirectional I²S bus data output
51 ST/SDI Bidirectional Stereo detection output / I²S bus data input
52 WS Bidirectional I²S bus word select output
53 SCK Bidirectional I²S bus clock output
54 BUS1 Bidirectional I²C bus expander output1
55 BUS0 Bidirectional I²C bus expander output2
56 IRQ Bidirectional I²C status read request

5.3 Block diagram

-11-
ⅤCHASSIS BLOCK DIAGRAM

-12-
Ⅵ SERVICE MODE&ADJUSTMENT
The Service-1 mode is entered by pressing the “SERVICE” key on
remote control when the TV is in ON condition and not in any Menu
mode. In service mode, by pressing “OK” key, Service-2 is accessed. by
pressing “OK” key again, Serivice-3 is accessed. By pressing “PP” key,
exit Service mode.

6.1 WHITE BALANCE ADJUSTMENT

The items within the Service-1 mode can be accessed using P+/P- keys
and the selected item can be modified by using V+/V- keys. The
parameters controlled in the Service-1 menu
are :
a) Red Gain ( 0 ... 63 )
b) DC Red ( 0 .... 127)
c) Green Gain ( 0 .... 63)
d) DC Green ( 0 .... 127)
e) Blue Gain ( 0 .... 63)
f) DC Blue ( 0 .... 127)
g) APR_threshold (0….15)
h) LOGO ( the first show the length of logo, and the followed is the
logo)
i) R-Cutoff (0…63)
j) G-Cutoff (0…63)
The display of Service-1 menu is showed as follows:

6.2 VIF ADJUSTMENT

When in Service-1 menu ,if “OK” key is pressed , Service-2 menu appears and the display
is as follows.The parameters controlled in the Service-2 menu are :
a) Tuner AGC ( 0 ... 63 )
b) Horizontal position 50 Hz( 0 ... 63)
c) Vertical position 50 Hz (0…15)
d) Vertical amplitude 50Hz (0…63)
e) Vertical linearity 50Hz (0…63)
f) Horizontal position 60 Hz( 0 ... 63)
g) Vertical position 60 Hz (0…15)
h) Vertical amplitude 60 Hz (0…63)
i) Vertical linearity 60 Hz (0…63)
j) Sub-Bright Maximum (0…63)
k) Sub-Bright Minimum (0…63)
l) Sub Tint (0…63)
m) VCO Coarse ( 0 ... 15)
n) VCO Fine ( 0 ... 127 )
o) VCO Coarse L1( 0 ... 15)
p) VCO Fine L1( 0 ... 127 )

-13-
The display of Service-2 menu is showed as shown:
The VCO status bar at the bottom of the screen appears only if either VCO Coarse item or VCO Fine item is
selected. The VCO status is read from the Read register of STV223X/4X and guides whether to Increase /
Decrease the VCO registers to attain VCO OK Status.
For doing VCO adjustment , Feed a 38.9MHZ Carrier as IF input and adjust VCO Coarse and fine parameters
to get VCO OK Status.
If the cursor is in VCO Coarse or Fine, and the display shows VCO OK status, then pressing of AV” key will
automatically put VCO fine to the Centre of the +60 to -60 KHz window.
For doing VCO L1 adjustment ,Feed a 33.9 MHZ carrier as IF input and adjust VCO Coarse L1 and VCO Fine
L1 to get VCO OK Status.
If the cursor is in VCO Coarse L1 or Fine L1 , and the display shows VCO OK status, then pressing of “AV” key
will automatically put VCO fine for L1 to the Centre of the +60 to -60 KHz window.
Another fast way of adjustment of VCO is to put the selection bar to either VCO Coarse or fine and press the
“AV” key. The VCO adjustment is done automatically. Similarly if you put the selection bar to VCO Coarse L1
or Fine L1 and press the “AV” key , the VCO L1 adjustment will be done automatically.
NOTE:Below items are not used in this chassis:
Vertical position 50 Hz
Vertical amplitude 50Hz
Vertical linearity 50Hz
Vertical position 60 Hz
Vertical amplitude 60 Hz
Vertical linearity 60 Hz

6.3 STV9306 ADJUSTMENT

When in Service-2 menu, if “OK” key is pressed, Service-3 menu appears and the display is as follows, if the
IC STV9306 has not been detected, then Service-4 (design menu) menu will appear.

1) Vertical amplitude for 50Hz signal.

2) Vertical amplitude for 60Hz signal.
3) Vertical shift (internal separated by 50Hz and 60Hz)
4) S Correction.
5) C Correction.
6) Horizontal width adjustment.
7) Pincushion Correction.
8) E/W Sharp Correction.
9) Trapezium Correction.

-14-
6.4 DESIGN OPTION SETTING
When in Service-3 menu, if “OK” key is pressed, Option menu appears and the display is as follows:

OPTION1
b7 = Over modulation (0=Disable, 1=Enable, it’s suggested to set it to 0 normally.)
b5 = P/N/S crystals application (0=2 Crystals, 1= 1 Crystals, according the quantity of crystal used for color
decoding in chassis.)
b4 = Cutoff Loop (0= OFF, 1=ON, it’s suggested to set it to 1 normally)
b3 = Safety Reset (0=Active, 1=Non, it’s suggested to set it to 0 normally)
b2 = MONO IN (0 = OFF, 1= ON, Depend on the sound decoding solution used in chassis. )
b1 = Sound Demodulation (0 = Intercarrier/MONO, 1 =QSS/NICAM, depend on the sound decoding solution
used in chassis.)
b0 = logo display (0 =OFF, 1= ON, it’s suggested to set it to 0 normally.)
OPTION2 (set to 0 by default)
b5 = HALF_CONTRAST (0 = OFF, 1=ON)
b4 = Color 6dB (0 = OFF, 1 = ON)
b3 = APR Feature (0 = ON, 1= OFF)
b2 = Black Stretch (0 = ON, 1= OFF)
b1 = Auto Flesh (0 = ON, 1= OFF)
b0 = Coring (0 = ON, 1 = OFF)
OPTION3
b7 =SMART (0 = OFF, 1=ON, it’s suggested to set it to 1 normally)
b5 = AVL (0 = OFF, 1=ON, it’s suggested to set it to 0 normally.)
b4 = PIF overmodulation (0 = OFF, 1= ON, it’s suggested to set it to 0 normally.)
b3 = Market_France --- secam LL (0 = OFF, 1 = ON, depend on the solution of chassis.)
b2 = Manual/Auto cutoff (0 = Manual, 1 = Auto cutoff, depend on the CRT for chassis.)
b1 = Mute pin low/high –to control the mute of speaker (0 = low, 1 = high, depend on the solution of chassis.)
OPTION4
b6 = WIDE MODE (0 = OFF, 1=ON, it’s suggested to set it to 0 normally.)
b4 = SCART2 (0 = OFF, 1=ON, depend on the solution of chassis.)
b3 = RGB (0 = OFF, 1= ON, depend on the solution of chassis.)
b2 = SVHS (0 = OFF, 1= ON, depend on the solution of chassis.)
b1 = AV2 (0 = OFF, 1= ON, depend on the solution of chassis.)

-15-
b0 = AV1 (0 = OFF, 1= ON, depend on the solution of chassis.)
OPTION5
There are 8 bits used in OPTION 5. They are b0, b1, b2, b3, b4, b5, b6 and b7.
For b0, normally, ST suggests to set it to 0.
For b1, b2, they are used to select teletext languages.
For b3, it’s used to enable AV3 and SVHS. When b3 is set to 0, SVHS is enabled. When b3 is set to 1 in
binary, the value is 8 in decimal. AV3 is enabled.

For b4, b5, b6 and b7 of OPTION 5 are also used to set the brightness of background in teletext mode. When
b4 b5 b6 and b7 are all set to 0, the brightness of teletext background is the same as brightness of TV
background. When b4, b5, b6 and b7 are all set to 1, it’s the maximum brightness of teletext background. It’s
the minimum brightness of teletext background when b4 is set to 1, and b5, b6 and b7 are all set to 0. you can
set these 4 bits according to your favorite brightness of teletext background.

A. for 11 OSD languages CPU ST92195C7B1/MNS and ST92195C7B1/MTH for east Europe, the setting of
the b1 and b2 is listed as below.
1. If b1 = b2 = 0, then the TEXT languages like “ENGLISH, FRENCH, SWEDISH, CZECH, GERMAN,
PORTUGUESE (SPANISH), ITALIAN, RUMANIAN” can be decoded;
2. If b1=1, b2=0, then the TEXT languages like “ENGLISH, RUSSIAN (BULGARIAN), HUNGARIAN,
TURKISH, GERMAN, PORTUGUESE (SPANISH), ITALIAN, RUMANIAN” can be decoded.
3. If b1=0, b2=1, then the TEXT languages like “POLISH, RUSSIAN (BULGARIAN), SWEDISH, SLOVAK,
GERMAN, SLOVENIAN, LITHUANIAN, RUMANIAN” can be decoded.
4. If b1 = b2 =1, then the TEXT languages like “POLISH, RUSSIAN (BULGARIAN), SWEDISH, CZECH,
GERMAN, CROATIAN, LETTISH, RUMANIAN” can be decoded.

B. for 12 OSD languages CPU ST92195C7B1/MNU and ST92195C7B1/MOK (SHRINK VERSION) for
Western Europe, the setting of the b1 and b2 is as below.
1. If b1 = b2 = 0, then the TEXT languages like “ENGLISH, FRENCH, FINNISH, CZECH, GERMAN,
PORTUGUESE (SPANISH), ITALIAN, GREEK” can be decoded;
2. If b1=1, b2=0, then the TEXT languages like “ENGLISH, FRENCH, DANISH, NORWEGIAN, GERMAN,
PORTUGUESE (SPANISH), ITALIAN, GREEK” can be decoded.
3. If b1=0, b2=1, then the TEXT languages like “POLISH, FRENCH, SWEDISH, CZECH, HOLLAND,
SERBIAN, ITALIAN, RUMANIAN” can be decoded.
4. If b1 = b2 =1, then the TEXT languages like “POLISH, FRENCH, SWEDISH, CZECH, GERMAN,
PORTUGUESE (SPANISH), LETTISH, RUMANIAN” can be decoded.
ST Text
b0 is used to change the process for adjusting Auto gain.
1) When CPU ST92195C7B1/MOK is used, the b0 is suggested to set to 0, the gain table for shrink version
should be selected.
2) When CPU ST92195C7B1/MNU is used, the b0 is suggested to set to 1, the gain table for normal version
will be selected.
b1, b2, b3 = select the correct process, only for ST engineer adjustment.
ROM_M6_P_valid | OSDEPROM_M6_R_valid | ROM_M6_R_valid | EPROM_M6_R_valid
EPROM_M6_R_valid | ROMLESS_H5_P_valid | ROM_H5_P_valid | EPROM_M6_A_valid
/* note: ROMLESS_M6_R_valid == ROM_M6_R_valid*/
b4 = Color transition for SVHS of STV224XX (0 = b5 is available, 1 = b5 is not available, and “SHARPNESS”
is no feature.)
b5 = (0 = STV224XH, 1 = STV224XC/D/E).
-16-
b6 = Tuner Drift Correction (0 = OFF, 1 = ON.)
b7 = RGB/DVD display on screen (0 = RGB, 1 = DVD.)
HPOS OSD,
Adjust horizontal position of OSD.
VPOS OSD,
Adjust vertical position of OSD.
HPOS TXT,
Adjust horizontal position of teletext.
VPOS TXT,
Adjust vertical position of teletext.
HOTEL MODE,
To set HOTEL MODE ON or OFF. When HOTEL MODE is enabled. The end user can not make any
adjustment of items in menu INSTALL, AUDIO and ORGANIZE. Menu INSTALL and AUDIO will disappear
automatically.
Volume Limit,
To set maximum volume of HOTEL MODE. It’s only available when HOTEL MODE is enabled.
SndSt 1
b0, b1, b2, b3 of SndSt 1 are used to set the sound output level at pin 26 and pin 27 of STV8216 with RF
signal. When b0, b1, b2, b3 of SndSt 1 are all set 0, the minimum sound output level will be got at pin 26 and
pin 27 of STV8216 with RF signal. When b0, b1, b2, b3 of SndSt 1 are all set 1, it’s 15 in decimal. The
maximum sound output level will be got at pin 26 and pin 27 of STV8216 with RF signal.
b4, b5, b6, b7 of SndSt 1 are used to set the “SURROUND” gain at pin 26 and pin 27 of STV8216 with RF &
AV signal. When b4, b5, b6, b7 of SndSt 1 are all set 0, the minimum “SURROUND” gain will be got at pin 26
and pin 27 of STV8216 with RF & AV signal. When b4, b5, b6, b7 of SndSt 1 are all set 1, it’s 240 in decimal.
The maximum “SURROUND” gain will be got at pin 26 and pin 27 of STV8216 with RF signal.
SndSt 2
b0, b2, b2, b3 of SndSt 2 are used to set the sound output level at pin 26 and pin 27 of STV8216 with AV
signal. When b0, b2, b2, b3 of SndSt 1 are all set 0, the minimum sound output level will be got at pin 26 and
pin 27 of STV8216 with AV signal. When b0, b2, b2, b3 of SndSt 1 are all set 1, it’s 15 in decimal. The
maximum sound output level will be got at pin 26 and pin 27 of STV8216 with AV signal.
b4, b5, b6, b7 of SndSt 2 are used to set the “EQUALIZER” gain at pin 26 and pin 27 of STV8216 with RF &
AV signal. When b4, b5, b6, b7 of SndSt 1 are all set 0, the maximum “EQUALIZER” gain will be got at pin 26
and pin 27 of STV8216 with RF & AV signal. When b4, b5, b6, b7 of SndSt 1 are all set 1, it’s 240 in decimal.
The minimum “EQUALIZER” gain will be got at pin 26 and pin 27 of STV8216 with RF & AV signal.
LL1 MAGC,
Just for SECAM LL1 SIF AGC setting purpose in STV8216. No available for PAL and NTSC system.
When the item “LL1 MAGC” is set to OFF, the SIF AGC of STV8216 is set by software.
When the item “LL1 MAGC” is set to ON, the SIF AGC of STV8216 can be set manually. The following steps
can be followed when set this item.
1) To get a RF SECAM LL1 signal without sound modulation, only sound carrier is available. And put the
signal to input of tuner in CTV 5 chassis.
2) To press “SERVICE” key on remote control to enter service menu. And select the item “LL1 MAGC” by
P+ or P- key on remote control.
Set the item “LL1 MAGC” from “OFF” to “ON” by V+ or V- key on remote control.
service command,
1) “PP”----exit
2) “OK”---- switch between the service menu

-17-
 3) “AV”---- auto VCO adjust
4) “MUTE” ---- one line gain
Enter service menu with user remote control,
1) Press key “Sleep” on remote control to set sleep time to “00:50”.
2) Within 5 seconds, press local key “V+” in TV set to enter service menu.
3) Adjust expecting item as the same as service remote control.

Ⅶ TEST POINT WAVE FORM&SCHEMATIC DIAGRAM

-18-
-19-
-20-
-21-
 R416
VI FBI SW LI RI VI FBI SW LI RI C423 1u/50V

100K

C417 100K
T2S08 CHASSIS SCHEMATIC DIAGRAM

+
VO RI GI BI LO RO VO RI GI BI LO RO C415 C420 C416 C419 C422
XS402
R414 C413

C421
SCL

C418

330p

330p
330p 330p 330p 330p 330p 220

R415

330p
21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1u/50V
SDA L407 15uH

+
IC701 CD7522CS
+5V-1
L406 15uH R413 10K C424
XS401

STDBY
OUT1+

OUT2+
1u/50V

OUT1-

OUT2-
GND1

GND2
GND
R807 X801 C823 22p L408 15uH

VCC

VOL
R813 33 C825 R417 220

IN1

IN2
47u/16V R419

+
+

D801
C827 + 68 L405 15uH

SCART1 ID
R707 0.47 R412 10K
27MHz R808 +12V-1

270K
Q801 2

V OUT1
10u/16V 220K

1N4148
C822

+
2SA1015 + C401 C406 C402 C405

V IN1

AO1R
AO1L
C706

L401 15uH

L404 15uH

L402 15uH

L403 15uH

AI1R
AI1L
C826 C824 C821 C820 R704 C703 C414

FBI
R804 R805 R806 0.1u

GI
470u/25V

RI

BI
22p 1u/50V

R708 2.2
100 100 4.7K 10K 330p 330p 330p 330p

R709 2.2
+
R705 3.3K C707
0.1u 0.1u 0.1u 0.47u/16V C403 C408 C404 C407
0.1u XS702
56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 330p 330p 330p 330p
SPK L
SCK

XTO

GNDSA
WS

CKTST

GNDP

VDDP

GNDSP

HPL
C709
BUS0

BUS1
IRQ

MCK

REG

SAD

HPD
ST

VDD2

GND2

GND1

VDD1

SCL

ADR
SYSCK
XTI

HPR
RESET
SD0
0.1u
STV8216

R SPK
IC801

XS701 C708 0.1u

MONOIN

TP21 CRT

GNDAH
VERFIF

VERFA
D501
VDDIF

GNDIF

VDDA

VDDH
GNDC

VMC1

VMC2
VDCC

BGAP
AO1R

AO2R
VTOP

AO1L

AO2L

AL3R
R506

R408 100K

R407 100K
AI1R

AI2R
AI1L

AI2L

AI3L

R401 10K

R402 10K
1N4007

R406 220

R405 220
KB

LSR
LSL

SW
SIF

OUT L
R810 18K C517 2.2K TP22
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
C511 D504

R501

1.2K
C812 C814 R812 R409 680p 1N4007 R515
C803 C804 C805 C817 C819 R701 680p KG
0.1u 4.7K C702 4.7K 68
0.1u C810 C809 10u/16V 10u/16V
C807 47u/16V 2.2K TP23
0.22u 0.1u Q701

R513
Q502

1.2K
0.1u + + 0.1u + + C829 Q702 C516 D506
2SA1015

+
2200p 2SC1815 680p 1N4007 R521
+

+
OUT R KR

1u/50V

1u/50V

1u/50V
L802 +

C411

C409

C412
C818 0.1u R702
10uH C808 C811 C815 R809 18K 2.2K
R802 C806 C813 10u/16V BF423
C802 0.1u 10u/16V 0.1u 10u/16V 10u/16V C816 R811 4.7K + D701 R519

SCART2 ID

1u/50V
10u/16V C830 Q504

C410
56p L803 0.1u 4.7K R703 C701 1N4148 1.2K
22 TP1 TP2 R803 10uH 2200p + + + + BF423
220u

V OUT2
100K

OUT R
OUT L

MUTE
330
AO1R

AO2R

AO2R
AO1L

AO2L

AO2L
V IN2
16V

+15V
Q507
AI1R

AI2R

AI2R
AI1L

AI2L

AI2L
+5V

+8V

+8V
SIF

BF423
C521
2200p/2KV
R520 R507

R524 10K

R523 10K

R522 10K
V OUT2
VSYNC

R OUT

B OUT
OSD G
+8V

+8V

OSD FB

OSD R

OSD B
+5V-1

H OUT

ICAT

G OUT
SC
10K 47K

ABL
SDA
SCL

TXT
Q207
TP3 TP4

2
2SC1815 R514 10K
R244 XP502
TU201 56K XS302
R505 10K
AGC

VCC

D202

1N4148
BU

BH
VT

BL

IF

R240 TP5 TP6 TP7

R257 R230 560 5.6V
1 2 3 4 5 6 7 8 9 10 11 1K 470 ZD501
AGC
IF
VT
L205 C239

R245

8.2K
R202 C216 10uH Q503
+ + 0.1u
R243 2SA1015
C220 R203 R201 2.2K
C212
27K 0.1u 100 L204

4700p
D203
22u/16V 4.7K

0.1u
47u/16V 10uH C245 C261

4700p
+

C243

2.2u/50V

470

470
15p

C242
C234 1K R231 Q501 Q504

R239
1N4148 470 XS101 XP501R508 4.7K

2.2K
0.1u +8V BF422 BF422 Q501

R236 27KC237
C238
4.7u R235 R233 R232

56K
X202 2SC1815
R502 100

R238

R246
R237
C214 + + C213 B OUT

R248

R247
C228 C227 C226
47u/16V 47u/16V C232 C241 C231 0.1u 0.1u 0.1u R234 R509
R510 100 R504

+
C235 G OUT R512

C229
0.1u
15K 2.2K 2.2K 0.1u 4.43 47K 100 R518
+ 1u/50V + 100 100 330 330 330
C510 C515

R229
470u MHz R OUT R516 100 C505
100u
16V 16V
L206 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 680p 680p 680p
+5V-1
+
FM CAP

GND1

OSD R

OSD B
AUDIO OUT

OSD FB

G OUT
VCC D

V AMP

XTAL1

XTAL2

XTAL3

ICAT
GND D

INTCVBSOUT CVBSOUT

R OUT

B OUT
OSD G
VCC1
SDA

SLPF
SCL

LFB

NC
H OUT

BCL
VERT

CLPF
10uH ICAT R526 22 C506
BSW2
100u/16V
BSW1
IC201

EXTAUDIAIN
STV2248

AM/FM OUT
AGCSIFCAP

AGCPIFCAP

Y/CVBS IN3
D111 AGC OUT

CVBS IN1

CVBS IN2
IC103 SW3 SW3 SW3 SW4 SW5 SW6
VREF IF

HFT505M

PIF LC1

PIF LC2

FB EXT
GND IF
HS0038
SIF IN1

SIF IN2

PIF IN1

PIF IN2

VCC IF
P- P- P- P+ V- V+

G EXT
IF PLL

B EXT

R EXT
GND2
VCC2

CHR

APR
IR

BS
R170 R015
510 1K 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
C801
47p TP8 TP9 C429 C428 C427
R219 FBI
C218 C426 C217

1u/50V
150 0.1u 0.1u 0.1u
1000p

+ + + + RI
C208

1u/50V
1u/50V

1u/50V
R221 L801 ABL-V
+ + + 150 10uH
L203
GI
R168 10 +12V
C225 BI
R801560

C127
R074 R074 R074 R075 R072 R073 C206 + IC301 STV9306
3.9K 3.9K 3.9K 6.2K 1K 2.2K R228
0.1u

FLYBACK
0.33u 330K R253

BREATH
EWSENS
C222 C223 C224 C209 C425

EWOUT
CRAMP

CHOLD
T201 75 R311

SENS2

SENS1
1u/50V 10u/16V 0.022u 1u/50V 1u/50V

VOPS
SYNC
R223

GND
C203

OUT
VCC
SDA
SCL
XS101 7K011 C219 1K R418 R423 R422 R421 R313 R312
0.1u 10uH R420 75 75 75
R224 15K 100K
+8V 5 4 5 4 75 R301 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 220K
1K 75 100
SF201 0.1u SCL
+5V K9650M SDA C304
Q202 0.68u C305
+

IC101 ST92195
3 3 C221 C233 + 2SC1815 R302 C303 R322
100
R314 R335 R324
10K 100 68K C307 R320
SF203 100
47u/16V 470u/16V

+
1 56 +5V 5.5MHz 100u/35V 2.2K
IR IN KB IN L202 + 0.1u R317 1K 1000p
Q201 V SYNC D302 1N4007
R171 10K 2SC1815 L201
RST 2 55 1 D201 2 1 SF202 2 10uH +24V
RESET NC K3953M 10uH R331 10 R323
+12V 2 1
R120 3 54 R137 39K 1N41 C210 C211
NC VT 0.56
48 R215 R211 R212 47u/16V 0.1u TP24 2 +

V CIOL
4.7K
R218

R217

R216

R122 4 53 + R329 10 C306 C308 R336

2
MUTE MUTE STDBY LED 10K 470 1K 1000u/16V 0.033u 470
C131 47p
C204
0.1u

C205 L302 C310 TP25

4.7K 2.2K 6.8K 2.2K 0.1u R213 ZD301
5 52 1mH 4.7u/160V
R136 6.8K NC STDBY LED R102 10K R214 C207 43V
STD BY 560
22K Q203
R110 4.7K R112 33K C312 0.01uF L301 31uH
+5V 6 51 +33V 2SC1815
STD BY OSC 0.1u
C309 C311
V OUT1
SIF SW

R101 1
+5V-1

R160 6.8K 1u/250V

V IN1

V IN2

H COIL
SCART1 ID 7 50 Q101 + 0.22uF
AGC

33K R312 1K
+8V

+8V

+8V

SERVICE OSC TP10

SIF

2N3904 D305
IF

IF

R105 6.8K C101 0.1u R308 10K RGP15J

SCART2 ID 8 49
SCART1 ID VOL PWM 2
X101
R109 2.7K IC601

+12V

+15V
9 48 R103
SCART2 ID VLIN PWM 33K H11A817 TP11 TP12 TP13
Q683 IC606 C658 IC603 C675 C318 470p/500V
R108 2.7K C102 7812 7808
R106 12K

R107 12K

10 47 4MHz C114 0.1u B892 220u/16V 47u/16V +8V + R326 220K

SDA TV /AV NC C603-C606 D603-D607 R638 3.3K V in V out V in V out
39p 1000p 1KV RM11C C607 + +
SCL GND GND C319
11 46 C115 VT C603 D603 D605 C605 100u/400V 10u/250V TP26
+5V S0 SIF SW 39p T604 D634 C657 C674 D308
C651
R104 33K + 15
RU3YX R685 0.1u 0.1u 0.1u RGP15J R399 ***
12 45 SIF SW TP14 3
S1 NC R620
GND SDA
VCC

SCL

C632
WC

180K C634 15K

R633 22 IC604 7805 47u/16V
IC102 +5V-1 T302 ***
13 44 BSW2 R602 470P 5 V in V out
24C08 NC PIF SW C661 + +
A0
A1
A2

5D11 IC605 GND HV

BSW1 R621 R625 100u/16V
14 43 V in V out C671
2

DATA PRT BSW2 180K 6.8 5 1

+

D105 +5V 9 0.1u SC

C645 470u/25V GND + TP15 R316
R123 10K 1N4148
OSD B 15 42 ZD102 C606 D606 D604 C604 D635 7805 C330
OSD B BSW1 RU4YX C639 +5V 47p D304 1
D104 5.1V 17 1N4148
R128 1K R129 1K 470u/16V R318 1K
C602 D614 R622 C616
OSD G 16 411N4148 R190 1K V SYNC
C613
15K 1000p 2KV R115 Q102
D303
OSD G V SYNC 4700p 1N4148 C637 R655 D101 C106 RGP15J
R127 1K R131 1K SC 0.22u 250V 470 2SA1015 1N4148 +24V
470P 1K ZD101 1u/50V RST 1
OSD R 17 40 TP19 TP20 R149 5.6K 3.9V + R310
OSD R H SYNC +5V R611 R116 +
R126 1K R133 1K 5.6K R619 Q613 R113 D310 1 FOCUS
OSD FB 18 39 + R143 10 T601 22 R624 ST1802 C635
R114 100K 1N4007 C320
C322
OSD FB AVDD1 C133 UF-LB-1604 39 1000u/25V 270 1000u/35V
C134 D617 4.7K 470p/500V
R134 1K 0.1u C614 R307
47u/16V RGP15J 2 TP16
MZ72-18

0.1u +140V
RT601

SDA R125 2.7K 19 38 16 2

SDA PXFM Q611 8 1
SCL R139 5.6K D631 +12V-1 SCREEN
2SA1015 2 RG2 +15V +
20
SCL JTRET0
37 13 +140V
C136 C135
T3.15A 250V

+ 4700p C601 R626 C617 R640 TP17 D311 C321

ZD601

2.7K C631 Q631 2SC1815 +33V 1N4007 22u/160V

21 36 0.22u 250V 2 R303
L101 C109 VDD GND 22p D616 470P + TP29

2
10uH 100u/16V C108 0.015u + R635 15K 150
F601 1N4148 150K C659
0.1u 11V C641 IC602
22 35 1uF/50V
JTD0 AGND C608 Q612 47u/160V uPC574 R325
C104 R617
C119 0.1u 400V 2.2K 8.2K C317 R321
220p R111 5.6K 0.47u/50V R124 1.5K 2SC3807 VR631 D636 +24V
23 34
+

WSCF TXT VIN TXT 2K R639 0.039u 8.2K

XS602 9 TP18 ABL-V
C121 XS603 R623 Q682
C105 0.22u 2.7K R637 15K ABL R319
24 33 82p 3 1N4148 2SC1815 STD BY
ESCR WSS XP601 L303 R249 22K
R130 C615 R615 D301
R119 6.8K 1.5K 150K H OUT T301 TP27 0.2uH BY228 10K
+5V R117 10 25 32 +5V 0.015u 22K + TP28
AVDD3 JTMS L601 C629 D641 R636 JDT1924
+ + 10K C326 Q302 C313 C314
C110 C122 R141 10 2200p 400V 6.2V C638
C112 26 31 SW601 0.22uF 0.1u + C246
47u/16V 0.1u TEST0 AVDD2 C111 DEGAUSSING COIL R629 2SC5296 7500p 4700p
R306
C103
0.1u 47u/16V
Q301 220
1.6KV 4.7u/50V Title: T2S08 CHASSIS SCHEMATIC DIAGRAM
4700p R118 5.6K 27 30 XS601 AC230V 8.2M 1/2W D309 C316
MCFM CVBS0 C123 1N4148 2SC2383 C315 D302
R121 15K
C324
220p
2KV
0.018uF RGP15J Number: Revision: 1
28 29 2200p
C113
22p
JTCK TXCF 2200p
50Hz 1. IS MARK OF CRITICAL COMPONENT Date: 20-May-2007 Sheet: 1 of 1
2.SUBJECT TO CHANGE WITHOUT NOTICE Described: Checked: Approved: