Re 17051

RE 17051
Edition: 2022-04
Replaces: 17049
Hydraulic cylinder
Tie rod design
Series CDT3…Z
▶ Nominal pressure 160 bar
▶ Maximum operating pressure up to 210 bar
▶ Component series 3X
Features Contents
▶ Installation dimensions according to ISO 6020-2 and Features1

NF/ISO 6020-2 Ordering code 2…4
▶ 13 types of mounting Technical data 5…8
▶ Piston Ø (ØAL): 25 … 200 mm Types of mounting 9
▶ Piston rod Ø (ØMM): 12 … 140 mm Dimensions 10 … 27
▶ Stroke length up to 3000 mm Leakage oil connection 28, 29
▶ Integrated guide socket for fast and easy maintenance Enlarged line connection 30
▶ Optional self-adjusting or adjustable end position Line connections, bleeding, leakage oil, throttle valve 31
damping Bleeding / measuring coupling 32
▶ Patented safety vent for easy and safe bleeding Piston rod ends "E" and "T" 33
▶ Easy assembly thanks to freely selectable position Swivel head, clevis bearing block 34 … 37
of the line connections at head and base Trunnion mounting bearing block 38, 39
Buckling 40 … 47
End position damping 48 … 52
Selection criteria for seals, seal kits 53, 54
Project planning software Tightening torques 55
Interactive Catalog System Components56
www.boschrexroth.com/tie-rod-cylinder Priming / painting 57
Project planning / maintenance instructions 58, 59
RE 17051, edition: 2022-04, Bosch Rexroth AG
2/58 Series CDT3 | Tie rod design
Ordering code
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21
CD T3 / / / Z 3X / *
01 Differential cylinder CD
02 Series T3
Types of mounting
03 according to DIN/ISO/NF
Rectangular flange at head ME5
Rectangular flange at base ME6
Self-aligning clevis at head MP5
Foot mounting MS2
Trunnion mounting in center MT4 1)
according to ISO/NF
Clevis at base MP1
Swivel eye at base MP3
Trunnion mounting at head MT1
Trunnion mounting at base MT2
Extended tie rod, on both sides MX1
Extended tie rod at base MX2
Extended tie rod at head MX3
Tapped hole at head MX5 2)
04 Piston Ø (ØAL) 25 … 200 mm
05 Piston rods Ø (ØMM) 12 … 140 mm 3)
06 Stroke length in mm 4)
Design principle
07 Head and base connected to tie rod Z
08 Component series 30 … 39 (30 … 39: Unchanged installation and mounting dimensions) 3X
Line connection − version

09 According to ISO 1179-1 (pipe thread) B
According to ISO 9974-1 (metric thread ISO 6149-1) R 5)
According to ISO 1179-1 (enlarged pipe thread) S 5)
Line connection − position at head (see page 31)

10 View to piston rod 1
2

3
4
Line connection − position at base (see page 31)

11 View to piston rod 1
2

3
4
Piston rod design
12 Hard chromium-plated C 6)
Hardened and hard chromium-plated H
Bosch Rexroth AG, RE 17051, edition: 2022-04

Tie rod design | series CDT3 3/58
Ordering code
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21
CD T3 / / / Z 3X / *
Piston rod end (see page 10 … 27)

13 Thread (ISO) for swivel head CGKA / CGKD D 7)
Internal thread E 8)
With mounted swivel head CGKA (DIN/ISO) F 9; 10)
Thread (DIN/ISO) for swivel head CGKA H 10)
With mounted swivel head CGKA / CGKD K 7); 11); 9)
With trunnion T 12)
End position damping (see page 48 … 52)

14 Without U
Both sides, self-adjusting D
Both sides, adjustable E 13)
Base side, self-adjusting K
Head side, self-adjusting S
Seal design (selection criteria for seals, see page 53)

15 For mineral oil HL, HLP and HFA
Standard seal system M
For mineral oil HL, HLP, HFA and water glycol HFC
Servo quality / reduced friction T
For phosphate ester HFDR
Servo quality / reduced friction S
Option 1
16 Without W
Measuring coupling, on both sides A
Leakage oil connection B 13); 14); 15)
Option 2
17 Without W
Specify the piston rod extension dimension "LY" in the plain text in mm Y
Color set-up
18 Priming class CP3 W
Painting class CP4 B 16)
Hydraulic fluid filling

19 Without W
With corrosion protection oil VG 68 F
Test certificate
20 Without W
With certificate of compliance 2.1 based on EN 10204 B
With acceptance test certificate 3.1 based on EN 10204 C
21 Further details in the plain text

Ordering code
Order example:
CDT3MP5/50/36/300Z3X/B11HHDMWW
When selecting, please observe the limitations on the
corresponding catalog pages!
Comments
1) Trunnion mounting position freely selectable; when ordering,
always specify the "XV" dimension in the plain text in mm.
2) Not according to ISO.
3) Observe the admissible piston rod Ø and assigned threads at the
piston rod end for 210 bar (pages 6 and 10 … 27).
4) Observe the maximum available stroke length page 7 and
admissible stroke length (according to buckling calculation)
page 41 to 47.
5) For type of mounting "ME5" and "ME6", only position 1 and 3
possible.
6) On request.
7) For operating pressure up to 210 bar.
8) Only with piston rod Ø 18 … 140 mm of the piston rod Ø
specified in the table on page 33 .
Observe the maximum operating pressure.
9) Not possible with type of mounting "MX1" and "MX3".
10) For operating pressure up to 160 bar.
11) CGKD only with piston Ø 160/110 and piston Ø 200 mm.
12) Only with piston rod Ø 22 … 140 mm of the piston rod Ø
specified in the table on page 33 . Observe the maximum
operating pressure.
13) With piston Ø 25 ... 100 mm: only line connection "B" possible.
With piston Ø 125 ... 200 mm: only types of mounting "ME5",
"ME6", "MP5", "MS2", "MT4" and line connection "B" possible.
With type of mounting "MX1" and "MX2", only possible for
piston Ø 40 ... 200.
14) With type of mounting "MS2" and piston Ø 25 and end position
damping, "E" is not possible.
15) Not possible with type of mounting "MT1".
16) Specify RAL color in the plain text.

Technical data
(For applications outside these values, please consult us!)
general
Installation position any
Ambient temperature range 1) °C ‒20 … +120
Priming see page 57
Painting see page 57
hydraulic
Nominal pressure bar 160
Minimum operating pressure 2) (without load) bar 10
Maximum operating pressure 3); 4) (only static load) bar 210
Static test pressure bar 240
Hydraulic fluid see table below
Hydraulic fluid temperature range °C see page 53
Viscosity range mm2/s 2.8 … 380
Viscosity at operating temperature (recommended) mm2/s 20 … 100
Maximum admissible degree of contamination of the Class 20/18/15
hydraulic fluid, cleanliness class according to ISO 4406 (c)
Bleeding by default
Hydraulic fluid Classification Data sheet

Mineral oils HL, HLP 90220
Phosphate ester HFDR 90222
Oil-in-water emulsion HFA 90223
Water glycol HFC 90223
1) See page 53.

2) Depending on the application, a certain minimum pressure is
required in order to guarantee good functioning of the cylinder.
Without load, a minimum pressure of 10 bar is recommended
for differential cylinders; for lower pressures, please contact us.
3) Static load: less than 10,000 load cycles over the entire life cycle.
4) The admissible dynamic operating pressure amounts to 75% of
the maximum operating pressure with maximum amplitude and
oscillatory load.
The specified operating pressures apply to applications with
shock-free operation with reference to excess pressure and/or
external loads. With extreme loads like e. g. high sequence cycle,
mounting elements and threaded piston rod connections must be
designed for durability.

Technical data
Stroke velocity
See information on stroke length and stroke velocity, the retraction velocity of the piston rod, drag-out losses of
higher stroke velocity on request. the medium may result. If necessary, please consult us.
If the extension velocity is considerably higher than
Line connection Maximum Line connection Maximum

Piston Ø Piston rod Ø
"B / R" stroke velocity "S" stroke velocity
ØAL ØMM
EE in m/s EE in m/s
in mm in mm
12 0.60 0.90
25 G1/4 G3/8
18 0.90 1.40
14 0.40 0.50
32 G1/4 G3/8
22 0.50 0.80
18 0.40 0.80
40 22 G3/8 0.40 G1/2 0.90
28 0.50 1.20
22 0.50 0.70
50 28 G1/2 0.60 G3/4 0.80
36 0.80 1.10
28 0.30 0.50
63 36 G1/2 0.40 G3/4 0.50
45 0.50 0.70
36 0.30 0.50
80 45 G3/4 0.30 G1 0.50
56 0.40 0.70
45 0.20 0.30
100 56 G3/4 0.20 G1 0.40
70 0.30 0.50
56 0.20 0.30
125 70 G1 0.20 G1 1/4 0.40
90 0.30 0.50
70 0.20 0.20
160 90 1) G1 0.20 G1 1/4 0.20
110 0.20 0.30
90 0.20 0.20
200 110 1) G1 1/4 0.20 G1 1/2 0.20
140 0.20 0.20
1) On request
Information on stroke length and stroke velocity

ØAL in mm 25 32 40 50 63 80 100 125 160 200
Minimum stroke in mm without damping – – – – – – – – – –
(recommended) with damping 30 32 46 44 50 54 56 66 72 80
Seal design M; 0.50 0.40 0.30 0.25
Maximum 160 bar
velocity in m/s Seal design M; 0.70 0.60 0.40 0.35
(recommended) 100 bar
Seal design T, S; 160 bar 1.00 0.80 0.60 0.50
Minimum Seal design M 30
velocity in mm/s Seal design T, S
(recommended) 1

Technical data
Areas, forces, flow (for operating pressure up to 210 bar)

Flow max.
Areas Force 1)
Piston Piston rod Area ratio at 0.1 m/s 2) available
Piston Rod Ring Pressure Diff. Pulling OFF Diff. ON stroke
length
ØAL ØMM ϕ A1 A2 A3 F1 F2 F3 qV1 qV2 qV3
in mm in mm A1/A3 in cm2 in cm2 in cm2 kN kN kN l/min l/min l/min
in mm4)
160 210 160 210 160 210 160 210
bar bar bar bar bar bar bar bar
12 - 1.3 1.1 3.8 - 1.8 - 6.1 - 0.7 2.3
25 4.9 7.9 2.9 600
18 18 2.1 2.5 2.4 10.3 4.1 5.3 3.8 5.0 1.5 1.4
14 - 1.3 1.5 6.5 - 2.5 - 40.4 0.9 3.9
32 8.0 12.9 4.8 800
22 22 1.9 3.8 4.2 16.9 6.1 8.0 6.8 8.9 2.3 2.5
18 - 1.3 2.5 10.0 - 4.1 - 16.0 - 1.5 6.0
40 22 22 1.4 12.6 3.8 8.8 20.1 26.4 6.1 8.0 14.0 18.4 7.5 2.3 5.3 1000
28 28 2.0 6.2 6.4 26.4 9.9 12.9 10.2 13.4 3.7 3.8
22 - 1.3 3.8 15.8 - 6.1 - 25.3 - 2.3 9.5
50 28 28 1.5 19.6 6.2 13.5 31.4 41.2 9.9 12.9 21.6 28.3 11.8 3.7 8.1 1200
36 36 2.1 10.2 9.5 41.2 16.3 21.4 15.1 19.9 6.1 5.7
28 - 1.3 6.2 25.0 - 9.9 12.9 40.0 - 3.7 15.0
63 36 36 1.5 31.2 10.2 21.0 49.9 65.5 16.3 21.4 33.6 44.1 18.7 6.1 12.6 1400
45 45 2.1 15.9 15.3 65.5 25.4 33.4 24.4 32.1 9.5 9.2
36 - 1.3 10.2 40.1 - 16.3 21.4 64.1 - 6.1 24.0
80 45 45 1.5 50.3 15.9 34.4 80.4 105.6 25.4 33.4 55.0 72.2 30.2 9.5 20.6 1700
56 56 2.0 24.6 25.6 105.6 39.4 51.7 41.0 53.8 14.8 15.4
45 - 1.3 15.9 62.6 - 25.4 33.4 100.2 - 9.5 37.6
100 56 56 1.5 78.5 24.6 53.9 125.7 164.9 39.4 51.7 86.3 113.2 47.1 14.8 32.3 2000
70 70 2.0 38.5 40.1 164.9 61.6 80.8 64.1 84.1 23.1 24.0
56 - 1.3 24.6 98.1 - 39.4 51.7 156.9 - 14.8 58.9
125 70 70 3) 1.5 122.7 38.5 84.2 196.4 3) 61.6 80.8 134.8 3) 73.6 23.1 50.5 2300
90 90 3) 2.1 63.6 59.1 3) 101.8 133.6 94.6 3) 38.2 35.5
70 - 1.3 38.5 162.6 - 61.6 80.8 260.1 - 23.1 97.5
160 90 3) 90 3) 1.5 201.1 63.6 137.4 321.7 422.2 101.8 133.6 219.9 288.6 120.6 38.2 82.5 2600
110 110 3) 1.9 95.0 106.0 3) 152.1 199.6 169.7 3) 57.0 63.6
90 - 1.3 63.6 250.5 - 101.8 133.6 400.9 - 38.2 150.3
200 110 3) 110 3) 1.4 314.2 95.0 219.1 502.7 659.7 152.1 199.6 350.6 460.2 188.5 57.0 131.5 3000
140 140 3) 2.0 153.9 160.2 3) 246.3 323.3 256.4 3) 92.4 96.1
A3 A1 A2
qV3 qV1 qV2
1) Theoretical static cylinder force 2) Stroke velocity

(without consideration of the efficiency and admissible load for 3) On request
attachment parts such as swivel heads, plates, or valves, etc.) 4) Larger stroke lengths upon request

Technical data
Weight for cylinder (in kg)

ØAL ØMM "MX1", "ME6", "MX2", "MX3",
"MP5" "MT4" "MT1", "MT2" Stroke 100 mm
in mm in mm "ME5", "S2" "MP3", "MP1" "MX5"
12 1.1 1.1 1.0 1.3 1.0 1.1 0.4
25
18 1.2 1.2 1.1 1.4 1.1 1.2 0.6
14 1.5 1.6 1.4 1.8 1.4 1.5 0.5
32
22 1.6 1.7 1.5 1.9 1.5 1.6 0.6
18 3.4 3.4 3.2 4.1 3.1 3.2 0.8
40 22 3.4 3.4 3.2 4.1 3.1 3.2 0.9
28 3.5 3.5 3.3 4.2 3.2 3.3 1.1
22 5.3 5.3 4.9 6.6 4.8 4.9 1.1
50 28 5.4 5.4 5 6.7 4.9 5 1.3
36 5.5 5.5 5.1 6.8 5.0 5.1 1.6
28 7.7 7.7 7.3 9.2 7.0 7.3 1.4
63 36 7.9 7.8 7.4 9.3 7.1 7.4 1.7
45 8.2 8.0 7.6 9.5 7.3 7.6 2.2
36 14 14 14 18 12 15 2.2
80 45 14 14 14 17 13 14 2.6
56 15 15 15 19 14 15 3.3
45 20 20 20 24 19 22 3.3
100 56 20 20 19 24 18 22 4.1
70 21 21 21 25 19 23 5.1
56 38 39 38 46 35 43 6.3
125 70 38 39 38 46 35 43 7.3
90 39 40 39 48 37 44 9.3
70 62 67 63 78 59 64 8.7
160 90 1) 63 68 64 79 60 66 10.7
110 64 69 65 80 61 67 13.2
90 112 120 115 147 107 114 13.4
200 110 1) 114 122 116 148 108 116 15.8
140 115 123 117 149 109 117 20.5
Swivel head, clevis bracket and trunnion mounting

bearing block see pages 34 … 39.
1) On request

Overview of types of mounting (for operating pressure up to 210 bar)
„ME5“ according to DIN/ISO/NF „MT1“ according to ISO/NF „MX5“ according to NF

(see page 10, 11) (see page 18, 19) (see page 24, 25)
„ME6“ according to DIN/ISO/NF „MT2“ according to ISO/NF

(see page 10, 11) (see page 18, 19)
„MP5“ according to DIN/ISO/NF „MX1“ according to ISO/NF

„MS2“ according to DIN/ISO/NF „MX2“ according to ISO/NF

„MT4“ according to DIN/ISO/NF „MX3“ according to ISO/NF

„MP1“ according to ISO/NF

(see page 26, 27)
„MP3“ according to ISO/NF

(see page 26, 27)

Dimensions: Rectangular flange at head "ME5"

Rectangular flange at base "ME6" (dimensions in mm)
"ME5" Y PJ + X* 4
GA J E H
SF F 2)
"X"
ØRD–0,2
ØMM
3 1
ØRD
ØDT
UO
KK
TO
EE
E
1)
3)
A VL ØB
VE R ØFB
WF GF 2
ZB + X*
"ME6"
4
Y PJ + X* E H
SF 2)
"X"
ØMM
3 1
ØDT
UO
TO
KK
EE
E
1)
A
WH GA GF ØB
R ØFB
ZJ + X*
2
1 ... 4 = Position of the line connections "X"

SF
ØC
Position of the line Position dimension "H"

connections "ME5" (head) "ME6" (base)
ØMM
1 1 1
KK
2 1 1
3 3 3
4 3 3
A WL
ØAL = Piston Ø 5) Thread for piston rod ends "D" and "K"
ØMM = Piston rod Ø 6) On request
X* = Stroke length 7) Position dimension "H" see table. "H" dimension always in position
1) Piston rod ends "E" and "T" see page 33 of the line connection, except for "ME5" (head) and "ME6" (base).
2) Tightening torque see page 55 8) "ME5": for line connection position "1" and "3" at head
3) Position of the line connections and the bleeding see page 31 9) "ME5": for line connection position "2" and "4" at head
4) Thread for piston rod ends "F" and "H"

Dimensions: Rectangular flange at head "ME5"

Rectangular flange at base "ME6" (dimensions in mm)
ØAL F ØFB GF R TO UO VE VL ZB ZJ ZK ZM
max H13 ME5/ME6 JS13 JS13 max max min max ±1 ±1 ±2
25 10 5.5 25 27 51 65 16 3 121 114 138 154
32 10 6.6 25/26.5 33 58 70 22 3 137 128 151 177
40 10 11 38 41 87 110 22 3 166 153 172 196
50 16 14 38 52 105 130 25 4 176 159 183 207
63 16 14 38 65 117 145 29 4 185 168 190 223
80 20 18 45 83 149 180 29 4 212 190 216 246
100 22 18 45 97 162 200 32 5 225 203 230 265
125 22 22 58 126 208 250 32 5 260 232 254 289
160 25 26 58 155 253 300 32 5 279 245 270 302
200 25 33 76 190 300 360 32 5 336 299 329 361
DIN / ISO 4) (for operating pressure ISO 5) (for operating pressure up to 210 bar)
up to 160 bar)
ØAL ØMM KK 4) A 4) ØC SF WL KK 5) A 5) ØC SF WL ØB ØRD
max max f9 f8
12 M10 x 1.25 14 11 10 5 – – – – – 24 3
25
18 M10 x 1.25 14 16.5 14 5 M14 x 1.5 18 16.5 14 5 30 38
14 M12 x 1.25 16 13 12 5 – – – – – 26 42
32
22 M12 x 1.25 16 20.5 18 5 M16 x 1.5 22 20.5 18 5 34 42
18 M14 x 1.5 18 16.5 14 5 – – – – – 30 62
40 22 M14 x 1.5 18 20.5 18 5 M16 x 1.5 22 20.5 18 5 34 62
28 M14 x 1.5 18 26 22 7 M20 x 1.5 28 26 22 7 42 62
22 M16 x 1.5 22 20.5 18 5 – – – – – 34 74
50 28 M16 x 1.5 22 26 22 7 M20 x 1.5 28 26 22 7 42 74
36 M16 x 1.5 22 34 30 8 M27 x 2 36 34 30 8 50 74
28 M20 x 1.5 28 26 22 7 – – – – – 42 75
63 36 M20 x 1.5 28 34 30 8 M27 x 2 36 34 30 8 50 88
45 M20 x 1.5 28 43 36 10 M33 x 2 45 43 36 10 60 88
36 M27 x 2 36 34 30 8 – – – – – 50 82
80 45 M27 x 2 36 43 36 10 M33 x 2 45 43 36 10 60 105
56 M27 x 2 36 54 46 10 M42 x 2 56 54 46 10 72 105
45 M33 x 2 45 43 36 10 – – – – – 60 92
100 56 M33 x 2 45 54 46 10 M42 x 2 56 54 46 10 72 125
70 M33 x 2 45 68 60 15 M48 x 2 63 68 60 15 88 125
56 M42 x 2 56 54 46 10 – – – – – 72 105
125 70 M42 x 2 56 68 60 15 M48 x 2 6) 63 68 60 15 88 150
90 M42 x 2 56 88 75 15 M64 x 3 6) 85 88 75 15 108 150
70 M48 x 2 63 68 60 15 – – – – – 88 125
160 90 6) M48 x 2 63 88 75 15 M64 x 3 85 88 75 15 108 170
110 M48 x 2 63 106 95 15 M80 x 3 6) 95 106 95 15 133 170
90 M64 x 3 85 88 75 15 – – – – – 108 150
200 110 6) M64 x 3 85 106 95 15 M80 x 3 95 106 95 15 133 210
140 M64 x 3 85 136 120 15 M100 x 3 6) 112 136 120 15 163 210
ØAL E Line connection "B" Line connection "R" GA H 7) J PJ 8) PJ 9) WF WH Y 8) Y 9)

EE ØDT min EE ØDT min "ME5"/"ME6" ±1.25 ±1.25 ±2 ±2 ±2 ±2
25 40 ± 1.5 G1/4 20.7 M14 x 1.5 21 46.5 5 22.5 53 64.5 25 15 50 38.5
32 45 ±1.5 G1/4 20.7 M14 x 1.5 21 48 5 25 56 68.5 35 25 60 47.5
40 63 ±1.5 G3/8 24.5 M18 x 1.5 26 52.5 – 33.5 73 77 35 25 62 58
50 75 ±1.5 G1/2 29.6 M22 x 1.5 29 57.5 – 33.5 74 78 41 25 67 63
63 90 ±1.5 G1/2 29.6 M22 x 1.5 29 57.5 – 35.5 80 81 48 32 71 70
80 115 ±1.5 G3/4 36.9 M27 x 2 34 67 – 41 93 93 51 31 77 77
100 130 ±2 G3/4 36.9 M27 x 2 34 70 – 43 101 101 57 35 82 82
125 165 ±2 G1 46.1 M33 x 2 43 80/76 – 54 117 117 57 35 86 86
160 205 ±2 G1 46.1 M33 x 2 43 83 – 58 130 130 57 32 86 86
200 245 ±2 G1 1/4 54 M42 x 2 52 107.5 – 77.5 165 165 57 32 98 98

Dimensions: Self-aligning clevis at base "MP5"

(dimensions in mm)
"Z"
4)
Y PJ + X* 1
Ø40‒200 E
ØDT
SF 3) 2) MS EP
EE
H
"X"
KK
.
3°
m ax
"Z"
ØMM
2 4
ØCX
ØB
max.
3°
1)
A EX
3
WH GA J LT
XO + X*
"X"
SF
ØC
ØMM
KK
A WL
1 ... 4 = Position of the line connections
ØAL ØCX EP EX LT XO MS
h13 min ±1.5 max
25 12–0.008 8 10–0.12 16 130 20
32 16–0.008 11 14–0.12 20 148 22.5
40 20–0.012 13 16–0.12 25 178 29
50 25–0.012 17 20–0.12 31 190 33
63 30–0.012 19 22–0.12 38 206 40
80 40–0.012 23 28–0.12 48 238 50
100 50–0.012 30 35–0.12 58 261 62
125 60–0.015 38 44–0.15 72 304 80
160 80–0.015 47 55–0.15 92 337 100
200 100–0.020 57 70–0.20 116 415 120

Dimensions: Self-aligning clevis at base "MP5"

(dimensions in mm)
DIN / ISO 5) (for operating pressure up to 160 bar) ISO 6) (for operating pressure up to 210 bar)
ØAL ØMM KK 5) A 5) ØC SF WL KK 6) A 6) ØC SF WL ØB
max max f9
12 M10 x 1.25 14 11 10 5 – – – – – 24
25
18 M10 x 1.25 14 16.5 14 5 M14 x 1.5 18 16.5 14 5 30
14 M12 x 1.25 16 13 12 5 – – – – – 26
32
22 M12 x 1.25 16 20.5 18 5 M16 x 1.5 22 20.5 18 5 34
18 M14 x 1.5 18 16.5 14 5 – – – – – 30
40 22 M14 x 1.5 18 20.5 18 5 M16 x 1.5 22 20.5 18 5 34
28 M14 x 1.5 18 26 22 7 M20 x 1.5 28 26 22 7 42
22 M16 x 1.5 22 20.5 18 5 – – – – – 34
50 28 M16 x 1.5 22 26 22 7 M20 x 1.5 28 26 22 7 42
36 M16 x 1.5 22 34 30 8 M27 x 2 36 34 30 8 50
28 M20 x 1.5 28 26 22 7 – – – – – 42
63 36 M20 x 1.5 28 34 30 8 M27 x 2 36 34 30 8 50
45 M20 x 1.5 28 43 36 10 M33 x 2 45 43 36 10 60
36 M27 x 2 36 34 30 8 – – – – – 50
80 45 M27 x 2 36 43 36 10 M33 x 2 45 43 36 10 60
56 M27 x 2 36 54 46 10 M42 x 2 56 54 46 10 72
45 M33 x 2 45 43 36 10 – – – – – 60
100 56 M33 x 2 45 54 46 10 M42 x 2 56 54 46 10 72
70 M33 x 2 45 68 60 15 M48 x 2 63 68 60 15 88
56 M42 x 2 56 54 46 10 – – – – – 72
125 70 M42 x 2 56 68 60 15 M48 x 2 7) 63 68 60 15 88
90 M42 x 2 56 88 75 15 M64 x 3 7) 85 88 75 15 108
70 M48 x 2 63 68 60 15 – – – – – 88
160 90 7) M48 x 2 63 88 75 15 M64 x 3 85 88 75 15 108
110 M48 x 2 63 106 95 15 M80 x 3 7) 95 106 95 15 133
90 M64 x 3 85 88 75 15 – – – – – 108
200 110 7) M64 x 3 85 106 95 15 M80 x 3 95 106 95 15 133
140 M64 x 3 85 136 120 15 M100 x 3 7) 112 136 120 15 163
ØAL E Line connection "B" Line connection "R" GA H 8) J PJ WH Y

EE ØDT min EE ØDT min ±1.25 ±2 ±2
25 40 ± 1.5 G1/4 20.7 M14 x 1.5 21 46.5 5 22.5 53 15 50
32 45 ±1.5 G1/4 20.7 M14 x 1.5 21 48 5 25 56 25 60
40 63 ±1.5 G3/8 24.5 M18 x 1.5 26 52.5 – 33.5 73 25 62
50 75 ±1.5 G1/2 29.6 M22 x 1.5 29 57.5 – 33.5 74 25 67
63 90 ±1.5 G1/2 29.6 M22 x 1.5 29 57.5 – 35.5 80 32 71
80 115 ±1.5 G3/4 36.9 M27 x 2 34 67 – 41 93 31 77
100 130 ±2 G3/4 36.9 M27 x 2 34 70 – 43 101 35 82
125 165 ±2 G1 46.1 M33 x 2 43 76 – 54 117 35 86
160 205 ±2 G1 46.1 M33 x 2 43 83 – 58 130 32 86
200 245 ±2 G1 1/4 54 M42 x 2 52 107.5 – 77.5 165 32 98
ØAL = Piston Ø 4) Grease nipple M6 DIN 71412 from piston Ø 40 mm

ØMM = Piston rod Ø 5) Thread for piston rod ends "F" and "H"
X* = Stroke length 6) Thread for piston rod ends "D" and "K"
1) Piston rod ends "E" and "T" see page 33 7) On request
2) Position of the line connections and the bleeding see page 31 8) "H" dimension always in line connection position
3) Tightening torque see page 55

Dimensions: Foot mounting "MS2"

(dimensions in mm)
Y PJ + X* 1
E
SF WH GA J 2) 3)
ØDT
EE
H
"X"
E/2
ØMM
4 2
KK
LH
ST
1)
AO AU AR ØB
XS SS + X* 3 ØSB
A TS
ZJ + X*
"Z" US
"X" "X"
SF
"Z"
ØC
ØMM
SB
KK
CO
KC
SS 3+0,5
0
XS A WL
ØAL CO KC LH ØSB SS ST TS US XS ZJ ZK ZM AO AU
N9 +0.2 h10 H13 ±1.25 JS13 max ±2 ±1 ±1 ±2
25 12 4) 3 4) 19 6.6 72 8.5 54 72 33 114 138 154 18 28.5

32 12 4) 4 4) 22 9 72 12.5 63 84 45 128 151 177 20 28
40 12 4 31 11 97 12.5 83 103 45 153 172 196 20 32.5
50 12 4.5 37 14 91 19 102 127 54 159 183 207 29.5 28
63 16 4.5 44 18 85 26 124 161 65 168 190 223 33 24.5
80 16 5 57 18 104 26 149 186 68 190 216 246 37.5 29.5
100 16 6 63 26 101 32 172 216 79 203 230 265 44 26
125 20 6 82 26 130 32 210 254 79 232 254 289 44 32
160 30 8 101 33 129 38 260 318 86 245 270 302 54 29
200 40 8 122 39 171 44 311 381 92 299 329 361 60 47.5

Dimensions: Foot mounting "MS2"

(dimensions in mm)
max max f9
12 M10 x 1.25 14 11 10 5 – – – – – 24
25
18 M10 x 1.25 14 16.5 14 5 M14 x 1.5 18 16.5 14 5 30
14 M12 x 1.25 16 13 12 5 – – – – – 26
32
22 M12 x 1.25 16 20.5 18 5 M16 x 1.5 22 20.5 18 5 34
18 M14 x 1.5 18 16.5 14 5 – – – – – 30
40 22 M14 x 1.5 18 20.5 18 5 M16 x 1.5 22 20.5 18 5 34
28 M14 x 1.5 18 26 22 7 M20 x 1.5 28 26 22 7 42
22 M16 x 1.5 22 20.5 18 5 – – – – – 34
50 28 M16 x 1.5 22 26 22 7 M20 x 1.5 28 26 22 7 42
36 M16 x 1.5 22 34 30 8 M27 x 2 36 34 30 8 50
28 M20 x 1.5 28 26 22 7 – – – – – 42
63 36 M20 x 1.5 28 34 30 8 M27 x 2 36 34 30 8 50
45 M20 x 1.5 28 43 36 10 M33 x 2 45 43 36 10 60
36 M27 x 2 36 34 30 8 – – – – – 50
80 45 M27 x 2 36 43 36 10 M33 x 2 45 43 36 10 60
56 M27 x 2 36 54 46 10 M42 x 2 56 54 46 10 72
45 M33 x 2 45 43 36 10 – – – – – 60
100 56 M33 x 2 45 54 46 10 M42 x 2 56 54 46 10 72
70 M33 x 2 45 68 60 15 M48 x 2 63 68 60 15 88
56 M42 x 2 56 54 46 10 – – – – – 72
125 70 M42 x 2 56 68 60 15 M48 x 2 7) 63 68 60 15 88
90 M42 x 2 56 88 75 15 M64 x 3 7) 85 88 75 15 108
70 M48 x 2 63 68 60 15 – – – – – 88
160 90 7) M48 x 2 63 88 75 15 M64 x 3 85 88 75 15 108
110 M48 x 2 63 106 95 15 M80 x 3 7) 95 106 95 15 133
90 M64 x 3 85 88 75 15 – – – – – 108
200 110 7) M64 x 3 85 106 95 15 M80 x 3 95 106 95 15 133
140 M64 x 3 85 136 120 15 M100 x 3 7) 112 136 120 15 163
ØAL E Line connection "B" Line connection "R" GA H 8) J PJ WH Y AR

25 40 ± 1.5 G1/4 20.7 M14 x 1.5 21 46.5 5 22.5 53 15 50 13.5
32 45 ±1.5 G1/4 20.7 M14 x 1.5 21 48 5 25 56 25 60 14
40 63 ±1.5 G3/8 24.5 M18 x 1.5 26 52.5 – 33.5 73 25 62 22.5
50 75 ±1.5 G1/2 29.9 M22 x 1.5 29 57.5 – 33.5 74 25 67 20
63 90 ±1.5 G1/2 29.6 M22 x 1.5 29 57.5 – 35.5 80 32 71 17.5
80 115 ±1.5 G3/4 36.9 M27 x 2 34 67 – 41 93 31 77 23
100 130 ±2 G3/4 36.9 M27 x 2 34 70 – 43 101 35 82 20
125 165 ±2 G1 46.1 M33 x 2 43 76 – 54 117 35 86 31
160 205 ±2 G1 46.1 M33 x 2 43 83 – 58 130 32 86 28
200 245 ±2 G1 1/4 54 M42 x 2 52 107.5 – 77.5 165 32 98 41.5
ØAL = Piston Ø 4) Not standardized

X* = stroke length 6) Thread for piston rod ends "D" and "K"

Dimensions: Trunnion mounting in center "MT4"

(dimensions in mm)
Y PJ + X* 1
E
TK J 2) 3) ØDT
WH GA
SF EE
H
"X"
r
4 2
ØMM
ØTD
UW
KK
E
1)
A XV4)
ØB
ZB + X* TM
UM
3
Dimensions for cylinder with piston rod extension dimension "LY" in retracted condition.
"X"
SF
ØC
ØMM
KK
1)
WH
LY XV4)
A WL

Notice:
We recommend lubricating the trunnion mounting on
a regular basis.
ØAL r ØTD TK TM UM UW X* XV XV ZB ZK ZM
f8 max h14 h15 max min min max max ±1 ±2
±2 ±2
25 1 12 20 48 68 43 1 74 80 + stroke 121 138 154
32 1 16 25 55 79 53 1 88 89 + stroke 137 151 177
40 1.6 20 30 76 108 74 1 95 104 + stroke 166 172 196
50 1.6 25 40 89 129 81 1 105 105 + stroke 176 183 207
63 2 32 50 100 150 97 10 117 107 + stroke 185 190 223
80 2.5 40 60 127 191 124 12 130 118 + stroke 212 216 246
100 2.5 50 70 140 220 137 18 142 124 + stroke 225 230 265
125 3.2 63 90 178 278 175 25 157 132 + stroke 260 254 289
160 3.5 80 110 215 341 212 40 171 131 + stroke 279 270 302
200 4.5 100 130 279 439 276 48 202 154 + stroke 336 329 361

Dimensions: Trunnion mounting in center "MT4"

(dimensions in mm)
max max f9
12 M10 x 1.25 14 11 10 5 – – – – – 24
25
18 M10 x 1.25 14 16.5 14 5 M14 x 1.5 18 16.5 14 5 30
14 M12 x 1.25 16 13 12 5 – – – – – 26
32
22 M12 x 1.25 16 20.5 18 5 M16 x 1.5 22 20.5 18 5 34
18 M14 x 1.5 18 16.5 14 5 – – – – – 30
40 22 M14 x 1.5 18 20.5 18 5 M16 x 1.5 22 20.5 18 5 34
28 M14 x 1.5 18 26 22 7 M20 x 1.5 28 26 22 7 42
22 M16 x 1.5 22 20.5 18 5 – – – – – 34
50 28 M16 x 1.5 22 26 22 7 M20 x 1.5 28 26 22 7 42
36 M16 x 1.5 22 34 30 8 M27 x 2 36 34 30 8 50
28 M20 x 1.5 28 26 22 7 – – – – – 42
63 36 M20 x 1.5 28 34 30 8 M27 x 2 36 34 30 8 50
45 M20 x 1.5 28 43 36 10 M33 x 2 45 43 36 10 60
36 M27 x 2 36 34 30 8 – – – – – 50
80 45 M27 x 2 36 43 36 10 M33 x 2 45 43 36 10 60
56 M27 x 2 36 54 46 10 M42 x 2 56 54 46 10 72
45 M33 x 2 45 43 36 10 – – – – – 60
100 56 M33 x 2 45 54 46 10 M42 x 2 56 54 46 10 72
70 M33 x 2 45 68 60 15 M48 x 2 63 68 60 15 88
56 M42 x 2 56 54 46 10 – – – – – 72
125 70 M42 x 2 56 68 60 15 M48 x 2 7) 63 68 60 15 88
90 M42 x 2 56 88 75 15 M64 x 3 7) 85 88 75 15 108
70 M48 x 2 63 68 60 15 – – – – – 88
160 90 7) M48 x 2 63 88 75 15 M64 x 3 85 88 75 15 108
110 M48 x 2 63 106 95 15 M80 x 3 7) 95 106 95 15 133
90 M64 x 3 85 88 75 15 – – – – – 108
200 110 7) M64 x 3 85 106 95 15 M80 x 3 95 106 95 15 133
140 M64 x 3 85 136 120 15 M100 x 3 7) 112 136 120 15 163
ØAL E Line connection "B" Line connection "R" GA H 8); 9) J PJ WH Y

25 40 ± 1.5 G1/4 20.7 M14 x 1.5 21 46.5 5 22.5 53 15 50
32 45 ±1.5 G1/4 20.7 M14 x 1.5 21 48 5 25 56 25 60
40 63 ±1.5 G3/8 24.5 M18 x 1.5 26 52.5 – 33.5 73 25 62
50 75 ±1.5 G1/2 29.6 M22 x 1.5 29 57.5 – 33.5 74 25 67
63 90 ±1.5 G1/2 29.6 M22 x 1.5 29 57.5 – 35.5 80 32 71
80 115 ±1.5 G3/4 36.9 M27 x 2 34 67 – 41 93 31 77
100 130 ±2 G3/4 36.9 M27 x 2 34 70 – 43 101 35 82
125 165 ±2 G1 46.1 M33 x 2 43 76 – 54 117 35 86
160 205 ±2 G1 46.1 M33 x 2 43 83 – 58 130 32 86
200 245 ±2 G1 1/4 54 M42 x 2 52 107.5 – 77.5 165 32 98
ØAL = Piston Ø 4) "XV" dimension in mm, always specify in the plain text
X* = Stroke length 6) Thread for piston rod ends "D" and "K"
3) Tightening torque see page 55 9) Piston Ø 25 and 32 mm: "H" dimension with line connection

Dimensions: Trunnion mounting at head "MT1"

trunnion mounting at base "MT2" (dimensions in mm)
"MT1" 1
Y PJ + X* UT
TC
WH GA J 2) 3) ØDT
SF EE
H
"X" r
4 2
ØMM
ØTD
ØB
KK
E
1)
A XG
3
ZB + X*
"X"
SF
ØC
Notice:
We recommend lubricating the trunnion mounting
ØMM
on a regular basis.
KK
A WL
"MT2"
Y PJ + X* 1
3) UT
WH GA 2)
TC
SF ØDT
EE
H
"X"
r
ØMM
ØB
KK
4 2
ØTD
E
1)
A XJ + X* n
3
ØAL n r TC ØTD UT XG XJ ZB ZK ZM
h14 f8 h15 ±2 ±1.25 max ±1 ±2
25 13 1 38 12 58 44 101 121 138 154
32 13 1 44 16 68 54 115 137 151 177
40 19 1.6 63 20 95 57 134 166 172 196
50 19 1.6 76 25 116 64 140 176 183 207
63 19 2 89 32 139 70 149 185 190 223
80 23 2.5 114 40 178 76 168 212 216 246
100 28 2.5 127 50 207 71 187 225 230 265
125 35 3.2 165 63 265 75 209 260 254 289
160 43 3.2 203 80 329 75 230 279 270 302
200 54.5 4.5 241 100 401 85 276 336 329 361

Dimensions: Trunnion mounting at head "MT1"

trunnion mounting at base "MT2" (dimensions in mm)
max max f9
12 M10 x 1.25 14 11 10 5 – – – – – 24
25
18 M10 x 1.25 14 16.5 14 5 M14 x 1.5 18 16.5 14 5 30
14 M12 x 1.25 16 13 12 5 – – – – – 26
32
22 M12 x 1.25 16 20.5 18 5 M16 x 1.5 22 20.5 18 5 34
18 M14 x 1.5 18 16.5 14 5 – – – – – 30
40 22 M14 x 1.5 18 20.5 18 5 M16 x 1.5 22 20.5 18 5 34
28 M14 x 1.5 18 26 22 7 M20 x 1.5 28 26 22 7 42
22 M16 x 1.5 22 20.5 18 5 – – – – – 34
50 28 M16 x 1.5 22 26 22 7 M20 x 1.5 28 26 22 7 42
36 M16 x 1.5 22 34 30 8 M27 x 2 36 34 30 8 50
28 M20 x 1.5 28 26 22 7 – – – – – 42
63 36 M20 x 1.5 28 34 30 8 M27 x 2 36 34 30 8 50
45 M20 x 1.5 28 43 36 10 M33 x 2 45 43 36 10 60
36 M27 x 2 36 34 30 8 – – – – – 50
80 45 M27 x 2 36 43 36 10 M33 x 2 45 43 36 10 60
56 M27 x 2 36 54 46 10 M42 x 2 56 54 46 10 72
45 M33 x 2 45 43 36 10 – – – – – 60
100 56 M33 x 2 45 54 46 10 M42 x 2 56 54 46 10 72
70 M33 x 2 45 68 60 15 M48 x 2 63 68 60 15 88
56 M42 x 2 56 54 46 10 – – – – – 72
125 70 M42 x 2 56 68 60 15 M48 x 2 6) 63 68 60 15 88
90 M42 x 2 56 88 75 15 M64 x 3 6) 85 88 75 15 108
70 M48 x 2 63 68 60 15 – – – – – 88
160 90 6) M48 x 2 63 88 75 15 M64 x 3 85 88 75 15 108
110 M48 x 2 63 106 95 15 M80 x 3 6) 95 106 95 15 133
90 M64 x 3 85 88 75 15 – – – – – 108
200 110 6) M64 x 3 85 106 95 15 M80 x 3 95 106 95 15 133
140 M64 x 3 85 136 120 15 M100 x 3 6) 112 136 120 15 163

25 40 ± 1.5 G1/4 20.7 M14 x 1.5 21 46.5 5 22.5 53 15 50
32 45 ±1.5 G1/4 20.7 M14 x 1.5 21 48 5 25 56 25 60
40 63 ±1.5 G3/8 24.5 M18 x 1.5 26 52.5 – 33.5 73 25 62
50 75 ±1.5 G1/2 29.6 M22 x 1.5 29 57.5 – 33.5 74 25 67
63 90 ±1.5 G1/2 29.6 M22 x 1.5 29 57.5 – 35.5 80 32 71
80 115 ±1.5 G3/4 36.9 M27 x 2 34 67 – 41 93 31 77
100 130 ±2 G3/4 36.9 M27 x 2 34 70 – 43 101 35 82
125 165 ±2 G1 46.1 M33 x 2 43 76 – 54 117 35 86
160 205 ±2 G1 46.1 M33 x 2 43 83 – 58 130 32 86
200 245 ±2 G1 1/4 54 M42 x 2 52 107.5 – 77.5 165 32 98
ØAL = Piston Ø 4) Thread for piston rod ends "F" and "H"
ØMM = Piston rod Ø 5) Thread for piston rod ends "D" and "K"
X* = Stroke length 6) On request
1) Piston rod ends "E" and "T" see page 33 7) "H" dimension always in line connection position
2) Position of the line connections and the bleeding see page 31

Dimensions: Extended tie rod, on both sides "MX1"

(dimensions in mm)
Y PJ + X*
ØDT ØDT
EE 2)
EE
1
H
BB BB
DD
1; 4)
"X"
3)
4 2
ØMM
TG
ØB
KK
E
AA
SF VD GA J
TG
WH
E
A ZJ + X*
3
"X"
SF
ØC
ØMM
KK
A WL
ØAL AA BB 4) TG VD ZJ ZK ZM
+3 js13 ±1.25 ±1 ±2
25 40 19 28.3 6 114 138 154
32 47 24 33.2 12 128 151 177
40 59 35 41.7 12 153 172 196
50 74 46 52.3 9 159 183 207
63 91 46 64.3 13 168 190 223
80 117 59 82.7 9 190 216 246
100 137 59 96.9 10 203 230 265
125 178 81 125.9 10 232 254 289
160 219 92 154.9 7 245 270 302
200 269 115 190.2 7 299 329 361

Dimensions: Extended tie rod, on both sides "MX1"

(dimensions in mm)
max max f9
12 M10 x 1.25 14 11 10 5 – – – – – 24
25
18 M10 x 1.25 14 16.5 14 5 M14 x 1.5 18 16.5 14 5 30
14 M12 x 1.25 16 13 12 5 – – – – – 26
32
22 M12 x 1.25 16 20.5 18 5 M16 x 1.5 22 20.5 18 5 34
18 M14 x 1.5 18 16.5 14 5 – – – – – 30
40 22 M14 x 1.5 18 20.5 18 5 M16 x 1.5 22 20.5 18 5 34
28 M14 x 1.5 18 26 22 7 M20 x 1.5 28 26 22 7 42
22 M16 x 1.5 22 20.5 18 5 – – – – – 34
50 28 M16 x 1.5 22 26 22 7 M20 x 1.5 28 26 22 7 42
36 M16 x 1.5 22 34 30 8 M27 x 2 36 34 30 8 50
28 M20 x 1.5 28 26 22 7 – – – – – 42
63 36 M20 x 1.5 28 34 30 8 M27 x 2 36 34 30 8 50
45 M20 x 1.5 28 43 36 10 M33 x 2 45 43 36 10 60
36 M27 x 2 36 34 30 8 – – – – – 50
80 45 M27 x 2 36 43 36 10 M33 x 2 45 43 36 10 60
56 M27 x 2 36 54 46 10 M42 x 2 56 54 46 10 72
45 M33 x 2 45 43 36 10 – – – – – 60
100 56 M33 x 2 45 54 46 10 M42 x 2 56 54 46 10 72
70 M33 x 2 45 68 60 15 M48 x 2 63 68 60 15 88
56 M42 x 2 56 54 46 10 – – – – – 72
125 70 M42 x 2 56 68 60 15 M48 x 2 7) 63 68 60 15 88
90 M42 x 2 56 88 75 15 M64 x 3 7) 85 88 75 15 108
70 M48 x 2 63 68 60 15 – – – – – 88
160 90 7) M48 x 2 63 88 75 15 M64 x 3 85 88 75 15 108
110 M48 x 2 63 106 95 15 M80 x 3 7) 95 106 95 15 133
90 M64 x 3 85 88 75 15 – – – – – 108
200 110 7) M64 x 3 85 106 95 15 M80 x 3 95 106 95 15 133
140 M64 x 3 85 136 120 15 M100 x 3 7) 112 136 120 15 163
ØAL DD E Line connection "B" Line connection "R" GA H 8) J PJ WH Y

25 M5 x 0.8 40 ± 1.5 G1/4 20.7 M14 x 1.5 21 46.5 5 22.5 53 15 50
32 M6 x 1 45 ±1.5 G1/4 20.7 M14 x 1.5 21 48 5 25 56 25 60
40 M8 x 1 63 ±1.5 G3/8 24.5 M18 x 1.5 26 52.5 – 33.5 73 25 62
50 M12 x 1.25 75 ±1.5 G1/2 29.6 M22 x 1.5 29 57.5 – 33.5 74 25 67
63 M12 x 1.25 90 ±1.5 G1/2 29.6 M22 x 1.5 29 57.5 – 35.5 80 32 71
80 M16 x 1.5 115 ±1.5 G3/4 36.9 M27 x 2 34 67 – 41 93 31 77
100 M16 x 1.5 130 ±2 G3/4 36.9 M27 x 2 34 70 – 43 101 35 82
125 M22 x 1.5 165 ±2 G1 46.1 M33 x 2 43 76 – 54 117 35 86
160 M27 x 2 205 ±2 G1 46.1 M33 x 2 43 83 – 58 130 32 86
200 M30 x 2 245 ±2 G1 1/4 54 M42 x 2 52 107.5 – 77.5 165 32 98
ØAL = Piston Ø 4) Observe the "BB" dimension for the swivel head assembly
ØMM = Piston rod Ø 5) Thread for piston rod end "H"
X* = Stroke length 6) Thread for piston rod end "D"

Dimensions: Extended tie rod at base "MX2"

Extended tie rod at head "MX3" (dimensions in mm)
"MX2"
Y PJ + X*
ØDT ØDT E
EE 2)
EE 1
H
1) BB
"X"
DD
4 2
ØMM
TG
KK
E
AA
SF
VD GA
TG
WH J
A ZJ + X* 3
"X"
SF
ØC
ØMM
KK
A WL
"MX3"
Y PJ + X* 1
ØDT
BB 3)
EE
H
2)
1; 4)
"X"
DD
ØMM
4 2
ØB
KK
TG
E
AA
SF VD GA J
WH TG
A ZJ + X* E
ZB + X*
3
ØAL AA BB 4) TG VD ZB ZJ ZK ZM
+3 js13 max ±1 ±1 ±2
25 40 19 28.3 6 121 114 138 154
32 47 24 33.2 12 137 128 151 177
40 59 35 41.7 12 166 153 172 196
50 74 46 52.3 9 176 159 183 207
63 91 46 64.3 13 185 168 190 223
80 117 59 82.7 9 212 190 216 246
100 137 59 96.9 10 225 203 230 265
125 178 81 125.9 10 260 232 254 289
160 219 92 154.9 7 279 245 270 302
200 269 115 190.2 7 336 299 329 361

Dimensions: Extended tie rod at base "MX2"

Extended tie rod at head "MX3" (dimensions in mm)
max max f9
12 M10 x 1.25 14 11 10 5 – – – – – 24
25
18 M10 x 1.25 14 16.5 14 5 M14 x 1.5 18 16.5 14 5 30
14 M12 x 1.25 16 13 12 5 – – – – – 26
32
22 M12 x 1.25 16 20.5 18 5 M16 x 1.5 22 20.5 18 5 34
18 M14 x 1.5 18 16.5 14 5 – – – – – 30
40 22 M14 x 1.5 18 20.5 18 5 M16 x 1.5 22 20.5 18 5 34
28 M14 x 1.5 18 26 22 7 M20 x 1.5 28 26 22 7 42
22 M16 x 1.5 22 20.5 18 5 – – – – – 34
50 28 M16 x 1.5 22 26 22 7 M20 x 1.5 28 26 22 7 42
36 M16 x 1.5 22 34 30 8 M27 x 2 36 34 30 8 50
28 M20 x 1.5 28 26 22 7 – – – – – 42
63 36 M20 x 1.5 28 34 30 8 M27 x 2 36 34 30 8 50
45 M20 x 1.5 28 43 36 10 M33 x 2 45 43 36 10 60
36 M27 x 2 36 34 30 8 – – – – – 50
80 45 M27 x 2 36 43 36 10 M33 x 2 45 43 36 10 60
56 M27 x 2 36 54 46 10 M42 x 2 56 54 46 10 72
45 M33 x 2 45 43 36 10 – – – – – 60
100 56 M33 x 2 45 54 46 10 M42 x 2 56 54 46 10 72
70 M33 x 2 45 68 60 15 M48 x 2 63 68 60 15 88
56 M42 x 2 56 54 46 10 – – – – – 72
125 70 M42 x 2 56 68 60 15 M48 x 2 7) 63 68 60 15 88
90 M42 x 2 56 88 75 15 M64 x 3 7) 85 88 75 15 108
70 M48 x 2 63 68 60 15 – – – – – 88
160 90 7) M48 x 2 63 88 75 15 M64 x 3 85 88 75 15 108
110 M48 x 2 63 106 95 15 M80 x 3 7) 95 106 95 15 133
90 M64 x 3 85 88 75 15 – – – – – 108
200 110 7) M64 x 3 85 106 95 15 M80 x 3 95 106 95 15 133
140 M64 x 3 85 136 120 15 M100 x 3 7) 112 136 120 15 163
ØAL DD E Line connection "B" Line connection "R" GA H 8) J PJ WH Y

25 M5 x 0.8 40 ± 1.5 G1/4 20.7 M14 x 1.5 21 46.5 5 22.5 53 15 50
32 M6 x 1 45 ±1.5 G1/4 20.7 M14 x 1.5 21 48 5 25 56 25 60
40 M8 x 1 63 ±1.5 G3/8 24.5 M18 x 1.5 26 52.5 – 33.5 73 25 62
50 M12 x 1.25 75 ±1.5 G1/2 29.6 M22 x 1.5 29 57.5 – 33.5 74 25 67
63 M12 x 1.25 90 ±1.5 G1/2 29.6 M22 x 1.5 29 57.5 – 35.5 80 32 71
80 M16 x 1.5 115 ±1.5 G3/4 36.9 M27 x 2 34 67 – 41 93 31 77
100 M16 x 1.5 130 ±2 G3/4 36.9 M27 x 2 34 70 – 43 101 35 82
125 M22 x 1.5 165 ±2 G1 46.1 M33 x 2 43 76 – 54 117 35 86
160 M27 x 2 205 ±2 G1 46.1 M33 x 2 43 83 – 58 130 32 86
200 M30 x 2 245 ±2 G1 1/4 54 M42 x 2 52 107.5 – 77.5 165 32 98
ØAL = Piston Ø 5) "MX2": Thread for piston rod ends "F" and "H"
ØMM = Piston rod Ø "MX3": Thread for piston rod end "H"
X* = Stroke length 6) "MX2": Thread for piston rod ends "D" and "K"
1) Piston rod ends "E" and "T" see page 33 "MX3": Thread for piston rod end "D"
2) Position of the line connections and the bleeding see page 31 7) On request
3) Tightening torque see page 55 8) "H" dimension always in line connection position
4) Observe the "BB" dimension for the swivel head assembly

Dimensions: tapped hole at head "MX5"

(dimensions in mm)
1
Y PJ + X* E
WH GA J 2) 3) ØDT
SF
EE
H
"X"
4 2
ØMM
TG
KK
E
AA
1)
VD BG 3
ØB RT
A ZJ + X*
ZB + X* TG
"X"
SF
ØC
ØMM
KK
A WL
ØAL AA BG RT TG VD ZB ZJ ZK ZM
min 6H js13 max ±1.25 ±1 ±2
25 40 8 M5 x 0.8 28.3 6 121 114 138 154
32 47 9 M6 x 1 33.2 12 137 128 151 177
40 59 12 M8 x 1.25 41.7 12 166 153 172 196
50 74 18 M12 x 1.75 52.3 9 176 159 183 207
63 91 18 M12 x 1.75 64.3 13 185 168 190 223
80 117 24 M16 x 2 82.7 9 212 190 216 246
100 137 24 M16 x 2 96.9 10 225 203 230 265
125 178 27 M22 x 2.5 125.9 10 260 232 254 289
160 219 32 M27 x 3 154.9 7 279 245 270 302
200 269 40 M30 x 3.5 190.2 7 336 299 329 361

Dimensions: tapped hole at head "MX5"

(dimensions in mm)
max max f9
12 M10 x 1.25 14 11 10 5 – – – – – 24
25
18 M10 x 1.25 14 16.5 14 5 M14 x 1.5 18 16.5 14 5 30
14 M12 x 1.25 16 13 12 5 – – – – – 26
32
22 M12 x 1.25 16 20.5 18 5 M16 x 1.5 22 20.5 18 5 34
18 M14 x 1.5 18 16.5 14 5 – – – – – 30
40 22 M14 x 1.5 18 20.5 18 5 M16 x 1.5 22 20.5 18 5 34
28 M14 x 1.5 18 26 22 7 M20 x 1.5 28 26 22 7 42
22 M16 x 1.5 22 20.5 18 5 – – – – – 34
50 28 M16 x 1.5 22 26 22 7 M20 x 1.5 28 26 22 7 42
36 M16 x 1.5 22 34 30 8 M27 x 2 36 34 30 8 50
28 M20 x 1.5 28 26 22 7 – – – – – 42
63 36 M20 x 1.5 28 34 30 8 M27 x 2 36 34 30 8 50
45 M20 x 1.5 28 43 36 10 M33 x 2 45 43 36 10 60
36 M27 x 2 36 34 30 8 – – – – – 50
80 45 M27 x 2 36 43 36 10 M33 x 2 45 43 36 10 60
56 M27 x 2 36 54 46 10 M42 x 2 56 54 46 10 72
45 M33 x 2 45 43 36 10 – – – – – 60
100 56 M33 x 2 45 54 46 10 M42 x 2 56 54 46 10 72
70 M33 x 2 45 68 60 15 M48 x 2 63 68 60 15 88
56 M42 x 2 56 54 46 10 – – – – – 72
125 70 M42 x 2 56 68 60 15 M48 x 2 6) 63 68 60 15 88
90 M42 x 2 56 88 75 15 M64 x 3 6) 85 88 75 15 108
70 M48 x 2 63 68 60 15 – – – – – 88
160 90 6) M48 x 2 63 88 75 15 M64 x 3 85 88 75 15 108
110 M48 x 2 63 106 95 15 M80 x 3 6) 95 106 95 15 133
90 M64 x 3 85 88 75 15 – – – – – 108
200 110 6) M64 x 3 85 106 95 15 M80 x 3 95 106 95 15 133
140 M64 x 3 85 136 120 15 M100 x 3 6) 112 136 120 15 163

25 40 ± 1.5 G1/4 20.7 M14 x 1.5 21 46.5 5 22.5 53 15 50
32 45 ±1.5 G1/4 20.7 M14 x 1.5 21 48 5 25 56 25 60
40 63 ±1.5 G3/8 24.5 M18 x 1.5 26 52.5 – 33.5 73 25 62
50 75 ±1.5 G1/2 29.6 M22 x 1.5 29 57.5 – 33.5 74 25 67
63 90 ±1.5 G1/2 29.6 M22 x 1.5 29 57.5 – 35.5 80 32 71
80 115 ±1.5 G3/4 36.9 M27 x 2 34 67 – 41 93 31 77
100 130 ±2 G3/4 36.9 M27 x 2 34 70 – 43 101 35 82
125 165 ±2 G1 46.1 M33 x 2 43 76 – 54 117 35 86
160 205 ±2 G1 46.1 M33 x 2 43 83 – 58 130 32 86
200 245 ±2 G1 1/4 54 M42 x 2 52 107.5 – 77.5 165 32 98
ØAL = Piston Ø 4) Thread for piston rod ends "F" and "H"
ØMM = Piston rod Ø 5) Thread for piston rod ends "D" and "K"
X* = Stroke length 6) On request
1) Piston rod ends "E" and "T" see page 33 7) "H" dimension always in line connection position
2) Position of the line connections and the bleeding see page 31

Dimensions: Clevis at base "MP1"

Swivel eye at base "MP3" (dimensions in mm)
"MP1"
Y PJ +X* L
5)
ØDT
2) MR
EE
H
SF
"X"
KK
"X"
ØMM
SF
ØB
ØC
1)
ØMM
KK
ØCDf8
SF
"X"
A WL
CB
UB
1)
3)
A WH GA
XC + X* 4)
Y PJ + X* "Z"
"MP3"
5) ØDT 1
2) 4)
MR E
EE EW
SF
H
ØCDH9
"X"
KK
"Z"
2 4
ØMM
ØB
1)
A
3
WH GA J L
XC + X*
ØAL CB ØCD EW L MR UB XC
A16 H9; f8 h14 min max max ±1.25
25 12 10 12 13 12 25 127
32 16 12 16 19 17 34 147
40 20 14 20 19 17 42 172
50 30 20 30 32 29 62 191
63 30 20 30 32 29 62 200
80 40 28 40 39 34 83 229
100 50 36 50 54 50 103 257
125 60 45 60 57 53 120 289
160 70 56 70 63 59 140 308
200 80 70 80 82 78 160 381

Dimensions: Clevis at base "MP1"

Swivel eye at base "MP3" (dimensions in mm)
max max f9
12 M10 x 1.25 14 11 10 5 – – – – – 24
25
18 M10 x 1.25 14 16.5 14 5 M14 x 1.5 18 16.5 14 5 30
14 M12 x 1.25 16 13 12 5 – – – – – 26
32
22 M12 x 1.25 16 20.5 18 5 M16 x 1.5 22 20.5 18 5 34
18 M14 x 1.5 18 16.5 14 5 – – – – – 30
40 22 M14 x 1.5 18 20.5 18 5 M16 x 1.5 22 20.5 18 5 34
28 M14 x 1.5 18 26 22 7 M20 x 1.5 28 26 22 7 42
22 M16 x 1.5 22 20.5 18 5 – – – – – 34
50 28 M16 x 1.5 22 26 22 7 M20 x 1.5 28 26 22 7 42
36 M16 x 1.5 22 34 30 8 M27 x 2 36 34 30 8 50
28 M20 x 1.5 28 26 22 7 – – – – – 42
63 36 M20 x 1.5 28 34 30 8 M27 x 2 36 34 30 8 50
45 M20 x 1.5 28 43 36 10 M33 x 2 45 43 36 10 60
36 M27 x 2 36 34 30 8 – – – – – 50
80 45 M27 x 2 36 43 36 10 M33 x 2 45 43 36 10 60
56 M27 x 2 36 54 46 10 M42 x 2 56 54 46 10 72
45 M33 x 2 45 43 36 10 – – – – – 60
100 56 M33 x 2 45 54 46 10 M42 x 2 56 54 46 10 72
70 M33 x 2 45 68 60 15 M48 x 2 63 68 60 15 88
56 M42 x 2 56 54 46 10 – – – – – 72
125 70 M42 x 2 56 68 60 15 M48 x 2 8) 63 68 60 15 88
90 M42 x 2 56 88 75 15 M64 x 3 8) 85 88 75 15 108
70 M48 x 2 63 68 60 15 – – – – – 88
160 90 8) M48 x 2 63 88 75 15 M64 x 3 85 88 75 15 108
110 M48 x 2 63 106 95 15 M80 x 3 8) 95 106 95 15 133
90 M64 x 3 85 88 75 15 – – – – – 108
200 110 8) M64 x 3 85 106 95 15 M80 x 3 95 106 95 15 133
140 M64 x 3 85 136 120 15 M100 x 3 8) 112 136 120 15 163

25 40 ± 1.5 G1/4 20.7 M14 x 1.5 21 46.5 5 22.5 53 15 50

32 45 ±1.5 G1/4 20.7 M14 x 1.5 21 48 5 25 56 25 60
40 63 ±1.5 G3/8 24.5 M18 x 1.5 26 52.5 – 33.5 73 25 62
50 75 ±1.5 G1/2 29.6 M22 x 1.5 29 57.5 – 33.5 74 25 67
63 90 ±1.5 G1/2 29.6 M22 x 1.5 29 57.5 – 35.5 80 32 71
80 115 ±1.5 G3/4 36.9 M27 x 2 34 67 – 41 93 31 77
100 130 ±2 G3/4 36.9 M27 x 2 34 70 – 43 101 35 82
125 165 ±2 G1 46.1 M33 x 2 43 76 – 54 117 35 86
160 205 ±2 G1 46.1 M33 x 2 43 83 – 58 130 32 86
200 245 ±2 G1 1/4 54 M42 x 2 52 107.5 – 77.5 165 32 98
ØAL = Piston Ø 4) Grease nipple M6 DIN 71412 from piston Ø 40 mm

ØMM = Piston rod Ø 5) Tightening torque see page 55
X* = Stroke length 6) Thread for piston rod ends "F" and "H"
1) Piston rod ends "E" and "T" see page 33 7) Thread for piston rod ends "D" and "K"
2) Position of the line connections and the bleeding see page 31 8) On request
3) Bolt included in the scope of delivery 9) "H" dimension always in line connection position

Leakage oil connection (dimensions in mm)
If technical high-quality seals are used, use of a leakage retraction velocity with larger strokes, permanent
oil connection is generally not necessary. A drag oil pressurization and the like. In case the extension
collection connection is only recommended in special velocities are more than 5 times the retraction velocity,
cases such as extension velocity more than 2 times please contact us.
"ME6", "MP1", "MP3", "MP5", "MT4", "MS2", "MT2", "ME5"

ØAL ØMM "MX1", "MX2", "MX3", "MX5"
e Y2 E3 e Y2
12 0 24.5 29 17 15
25
18 0 24.5 29 17 15
14 0 24.5 31.5 18 15
32
22 0 24.5 31.5 18 15
18 0 26 35.5 22 15
40 22 0 26 35.5 22 15
28 0 26 35.5 22 15
22 14.5 28 – 34 15
50 28 14.5 28 – 34 15
36 14.5 28 – 34 15
28 16 25.5 – 43 12
63 36 16 25.5 – 43 12
45 16 25.5 – 43 12
36 16 29 – 27 15
80 45 16 29 – 27 15
56 16 29 – 27 15
45 16 30 – 30 14
100 56 16 27 – 30 14
70 16 27 – 30 14
56 18 30.5 – 32 16
125 70 18 30.5 – 39 16
90 18 30.5 – 39 16
70 24 31.5 – 30 13
160
90 1) 24 31.5 – 40 13
110 24 31.5 – 40 13
90 24 38.5 – 45 26
200
110 1) 24 38.5 – 60 26
140 24 38.5 – 60 26
1) On request

Leakage oil connection (dimensions in mm)
Ø 25, 32, 40 (except for "ME5")
Y
Y2
4
E3
Ø 50 … 200, "ME5": Ø 25 … Ø 200
G1/8 e
Y2 1
4 2

Enlarged line connection (dimensions in mm)
The line connections of this series are generously comply with the standard dimensions, see table.
dimensioned according to the standard; with high velocity, Cannot be realized for the types of mounting
the pressure drop ∆p can be reduced by using larger "ME5" and "ME6" with connection position 2 or 4.
oil ports; sometimes, it is, however, no longer possible to
Y PJ Tightening torque MA
ØAL EE H1 SW Øa
±2 ±1.25 Nm (±5 %)
25 G3/8 20 50 53 27 9 20
32 G3/8 20 60 56 27 9 20
40 G1/2 23 62 73 32 11 26
50 G3/4 29 67 74 41 14 48
63 G3/4 29 71 80 41 14 48
80 G1 33 77 93 46 18 74
100 G1 33 82 101 46 18 74
125 G1 1/4 39 86 117 60 23 127
160 G1 1/4 – 86 130 – – –
200 G1 1/2 – 98 165 – – –
SW
Y PJ + stroke EE
Øa
H1
4 2

Position of line connections, bleeding, leakage oil, throttle valve

SW F1
1L 1 1R
4O 2O
F
4 2
F2
4U 2U
L2
3L
L1
L3 L4 + X* E1
E2 3R
Bleeding Leakage oil Throttle valve

Type of mounting Line connection
Head Base Head Head Base
"MP5", "MT4", 1 2 2 1 3R 3R
"MP1", "MP3", 2 3 3 2 4U 4U
"MX1", "MX2", 3 4 4 3 1L 1L
"MX3", "MX5" 4 1 1 4 2O 2O
1 2 2 1R 3R 3R
2 3R 3 1R 1L 4U
"ME5"
3 4 4 3L 1L 1L
4 1L 1 3L 3R 2O
"MS2" 1 2O 2O 1 4O 4O
1 3L 2 – 3R 3R
"MT1"
3 1R 4 – 1L 1L
1 2 3L 1 3R 3R
"MT2"
3 4 1R 3 1L 1L
1 2 2 1 3R 3R
2 3 3 2 4U 1L
"ME6"
3 4 4 3 1L 1L
4 1 1 4 2O 3R
F F1 F2 Throttle valve adjustable on both sides

Head/base1) Position Position Protrusion Center offset Dimension
Line Bleeding
ØAL connection MA
in mm Nm
(head) 1) 1) SW L1 L2 E1 E2 L3 L4
2/4 1/3 2/4 1/3 2/4 Allen (head) (base) (head) (base)
2) "ME5" "MT1" "MS2" "ME5" "ME5" wrench
25 0 0 6 5 11.5 23 23 11.5 5 3) 12 12 6 6 48 57 5
32 0 0 5 5 13 25.5 25.5 13 5 3) 12 12 9 9 57.5 61 5
40 10 10 10 10 15.5 19.5 15.5 15.5 5 5.5 5.5 8 8 61.5 74 5
50 10 10 10 10 15.5 29.5 15.5 15.5 5 3 3 10 10 67 74 5
63 14 14 14 14 18.5 20 18.5 18.5 5 0 0 15 15 72 78 5
80 10 10 10 10 21 21 21 21 6 0 0 14 14 81 85 15
100 24 24 12 12 23 23 23 23 6 0 0 13 13 86 93 15
125 0 0 12 0 25 25 25 25 6 – – 22 22 91.5 109 24
160 0 0 0 0 29 29 29 29 6 – – 30 30 93.5 115 24
200 0 0 0 0 41.5 41.5 31.5 31.5 6 – – 30 30 114 128 24
X* = stroke length 2) Types of mounting "ME5" (only base), "ME6", "MP5", "MT4",
MA = tightening torque "MP1", "MP3", "MT2", "MX1", "MX2", "MX3" and "MX5"
1) Position of line connection 3) Protrusion 3 mm

Bleeding / measuring coupling (dimensions in mm)
By default, a patented safety vent against unintended The port allows for the installation of a measuring
screwing out in head and base is delivered for piston coupling with check valve for pressure measurement or
Ø ≥ 40 mm. contamination-free bleeding. Measuring coupling with
For piston Ø 25 and 32 mm, a bleed screw G1/8 is check valve function, i.e. it can also be connected when
installed in head and base which is not secured the system is pressurized.
against screwing out.
Connection possibility for measuring coupling
Piston Ø (AL) 25 and 32 mm Piston Ø (AL) 40 … 200 mm
3 mm
D1 D1
SW SW
Scope of delivery: Measuring coupling G1/8

Ø20 MESSKUPPLUNG AB 20-11/K3 G1/8 with seal ring made of NBR
Material no. R900014363
MESSKUPPLUNG AB 20-11/K3V G1/8 with seal ring made of FKM
M16 x 2
max. 39
Scope of delivery: Measuring coupling G1/4

MESSKUPPLUNG AB 20-11/K1 G1/4 with seal ring made of NBR
MESSKUPPLUNG AB 20-11/K1V G1/4 with seal ring made of FKM
D2
SW 19
Bleed screw Measuring coupling Tightening torque

MA
ØAL D1 Fuse SW D2 Nm
25 and 32 G1/8 not secured 5 G1/8 18
40 ... 63 G1/8 secured 5 G1/8 18
80 … 200 G1/4 secured 6 G1/4 40

Piston rod ends "E" and "T" (dimensions in mm)
Internal thread "E" Trunnion "T"

ND NE
SF r
ØMM
ØNB
ØMM
ØNC
ØC
KF
Force transmission area

AF
WH/WF
ØAL ØMM KF AF ØC SF ØNB ØNC ND / NE r pmax. 1)

h13 h13 h13 / H11 bar
25 18 M12 x 1.25 18 17 14 – – – – –
32 22 M16 x 1.5 22 21 18 18 11.2 8 0.5 160
18 M12 x 1.25 18 17 14 – – – – –
40
28 M20 x 1.5 28 25 22 22.4 14 10 0.5 160
22 M16 x 1.5 22 21 18 18 11.2 8 0.5 105
50
36 M27 x 2 36 34 30 28 18 12.5 0.8 190
28 M20 x 1.5 28 25 22 22.4 14 10 0.5 95
63
45 M33 x 2 45 43 36 35.5 22.4 16 0.8 160
36 M27 x 2 36 34 30 28 18 12.5 0.8 105
80
56 M42 x 2 56 53 46 45 28 20 1.2 160
45 M33 x 2 45 43 36 35.5 22.4 16 0.8 90
100
70 M48 x 2 63 67 60 56 35.5 25 1.2 160
56 M42 x 2 56 53 46 45 28 20 1.2 100
125
90 M64 x 3 85 86 75 78 45 30 1.5 160
70 M48 x 2 63 67 60 56 35.5 25 1.5 90
160
110 M80 x 3 95 106 95 106 65 35 1.5 160
90 M64 x 3 85 88 75 78 45 30 1.5 90
200
140 M100 x 3 112 136 120 136 70 45 1.5 160
1) with pulling load

Swivel head CGKA – AP 6 (clampable) (dimensions in mm)
ISO 8133 / ISO 8132
Type Material no. KK AX Øb C CH ØCN EN EU LF MA 7) m 8) C0 9) Fadm 10)

6H min max js13 max min Nm kg (head) kN
kN
CGKA 12 3) R900327186 M10x1.25 15 17 40 42 12 –0.008 10 –0.05 8 16 9.5 0.15 17 6.3
CGKA 16 4) R900327192 M12x1.25 17 21 45 48 16 –0.008 14 –0.05 11 20 9.5 0.25 28.5 10.5
CGKA 20 4) R900306874 M14x1.5 19 25 55 58 20 –0.010 16 –0.05 13 25 23 0.43 42.5 15.7
CGKA 25 R900327191 M16x1.5 23 30 65 68 25 –0.010 20 –0.05 17 30 23 0.73 67 24.7
CGKA 30 R900327187 M20x1.5 29 36 80 85 30 –0.010 22 –0.05 19 35 46 1.3 108 39.9
CGKA 40 R900327188 M27x2 37 45 100 105 40 –0.012 28 –0.05 23 45 46 2.3 156 57.6
CGKA 50 R900327368 M33x2 46 55 125 130 50 –0.012 35 –0.05 30 58 80 4.4 245 90.4
CGKA 60 R900327369 M42x2 57 68 160 150 60 –0.015 44 –0.05 38 68 195 8.4 380 140.2
CGKA 80 R900327370 M48x2 64 90 205 185 80 –0.015 55 –0.15 47 82 6) 385 15.6 585 215.9
CGKA 100 R900327371 M64x3 86 110 240 240 100 –0.02 70 –0.2 57 116 660 28 865 319.2
CGKD 100 5) R900322030 M80x3 96 110 210 210 100 H7 100 h12 84 98 385 28 1060 391.1
CGKD 125 5) R900322026 M100x3 113 135 262 260 125 H7 125 h12 102 120 385 43 1430 527.7
1) Grease nipple, cone head form A according to DIN 71412

2) Related bolt Ø h6 Notice:
3) Cannot be re-lubricated Geometry and dimensions may differ depending on
the manufacturer.
4) Can be re-lubricated via lubricating hole
In case of combination with other mounting elements,
5) Swivel head according to ISO 8132, related bolt Ø m6
the usability must be checked.
6) Dimensions may differ from the standard depending
on the manufacturer The swivel head must always be screwed against the piston rod
7) MA = tightening torque shoulder. Afterwards, the clamping screws must be tightened
8) m = mass of swivel head in kg with the specified tightening torque.
9) C0 = static load rating of the swivel head
10) Fadm= maximum admissible load on the swivel head
during oscillatory or alternating loads

Clevis–bearing block CLCB – AP 5 (clampable) (dimensions in mm)
ISO 8133
Type Material no. Nominal force ØCF CP CG CO FO FM GL ØHB ØS

kN K7 1) h14 + 0.1 N9 js14 js13 JS13 H13
+ 0.3
CLCB 12 R900326960 8 12 30 10 10 16 40 46 9 15
CLCB 16 R900327372 12.5 16 40 14 16 18 50 61 11 18
CLCB 20 R900327373 20 20 50 16 16 20 55 64 14 3) 20
CLCB 25 R900326961 32 25 60 20 25 22 65 78 16 3) 24
CLCB 30 R900327374 50 30 70 22 25 24 85 97 18 3) 26
CLCB 40 R900327375 80 40 80 28 36 24 100 123 22 33
CLCB 50 R900327376 125 50 100 35 36 35 125 155 30 48
CLCB 60 R900327377 200 60 120 44 50 35 150 187 39 60
CLCB 80 R900327378 320 80 160 55 50 35 190 255 45 80
CLCB 100 R900327379 500 100 200 70 63 35 210 285 48 80
Type KC KL LG LJ LO RE SL SR TA UJ UK m 2)
+0.3 max js13 max js13 max max in kg
CLCB 12 3.3 8 28 29 56 55 40 12 40 75 60 0.6
CLCB 16 4.3 8 37 38 74 70 50 16 55 95 80 1.3
CLCB 20 4.3 10 39 40 80 85 62 20 58 120 90 2.1
CLCB 25 5.4 10 48 49 98 100 72 25 70 140 110 3.2
CLCB 30 5.4 13 62 63 120 115 85 30 90 160 135 6.5
CLCB 40 8.4 16 72 73 148 135 100 40 120 190 170 12.0
CLCB 50 8.4 19 90 92 190 170 122 50 145 240 215 23.0
CLCB 60 11.4 20 108 110 225 200 145 60 185 270 260 37.0
CLCB 80 11.4 26 140 142 295 240 190 80 260 320 340 79.0
CLCB 100 12.4 30 150 152 335 300 235 100 300 400 400 140.0
1) Related bolt Ø h6, suitable for swivel head CGKA...

(bolt and bolt lock are included in the scope of delivery) Notice:
2) m = mass of clevis bracket Geometry and dimensions may differ depending on
3) Dimensions may differ from the standard depending the manufacturer.
on the manufacturer In case of combination with other mounting elements,

Clevis bracket CLCA (clampable) (dimensions in mm)
ISO 8132, form B
ØAL ØMM Type Material no. Nominal force ØCK CL CM CO FG FL FO ØHB

kN H9 1) h16 A12 N9 js14 js12 js14 H13
160 110 CLCA 100 2) 500 100 210 100 63 52.5 180 0 52
200 110 CLCA 100 2) 500 100 210 100 63 52.5 180 0 52
200 140 CLCA 125 2) 800 125 270 125 80 75 230 0 52
ØAL ØMM Type KC KL LE MR RF RG ØS SL UK UX m 3)

+0.3 min. max. js14 js14 max. max. in kg
160 110 CLCA 100 12.4 30 120 100 315 250 76 246 405 345 99.2
200 110 CLCA 100 12.4 30 120 100 315 250 76 246 405 345 99.2
200 140 CLCA 125 15.4 32 170 125 365 350 76 310 455 450 174.1
ØAL = piston Ø
ØMM = Piston rod Ø Notice:
1) Related bolt Ø m6 Geometry and dimensions may differ depending on
(bolt and bolt lock are included in the scope of delivery and the manufacturer.
are not mounted upon delivery) In case of combination with other mounting elements,
the usability must be checked. The clevis brackets are
2) On request
suitable for attachment in case of type of mounting MP5
3) m = mass of clevis bracket
and at the swivel head.

Clevis bracket CLCD (clampable) (dimensions in mm)
ISO 8132, form A
ØAL ØMM Type Material no. Nominal force ØCK CL CM FL ØHB

kN H9 1) h16 A12 js12 H13
160 110 CLCD 100 2) 500 100 210 100 180 45
200 110 CLCD 100 2) 500 100 210 100 180 45
200 140 CLCD 125 2) 800 125 270 125 230 52
ØAL ØMM Type KL LE MR RC ØS SL TB UR UH m 3)

min. max. js14 js14 max. max. in kg
160 110 CLCD 100 30 120 100 160 66 246 315 260 400 74
200 110 CLCD 100 30 120 100 160 66 246 315 260 400 74
200 140 CLCD 125 32 170 125 200 76 310 385 320 470 129
ØAL = Piston Ø
ØMM = Piston rod Ø Notice:
1) Related bolt Ø m6 Geometry and dimensions may differ depending on
(bolt and bolt lock are included in the scope of delivery and the manufacturer.
are not mounted upon delivery) In case of combination with other mounting elements,
the usability must be checked. The clevis brackets are
2) On request
suitable for attachment in case of type of mounting MP5
3) m = mass of clevis bracket in kg
and at the swivel head.

Trunnion mounting– bearing block CLTA–AT 4 (clampable) (dimensions in mm)
CLTA 12–20
ØAL Type Material no. Nominal ØCR CO FK FN FS ØHB KC NH TH UL l1 l2 l3 m 5)

force H7 N9 js12 max JS14 H13 +0.3 max JS14 max in kg
kN 4)
25 CLTA 12 R901071355 8 12 10 38 55 8 9 3.3 17 3) 40 63 25 25 1 0.5
32 CLTA 16 R901071364 12.5 16 16 45 65 10 11 4.3 21 50 80 30 30 1 0.9
40 CLTA 20 R901071365 20 20 16 55 80 10 11 4.3 21 60 90 40 38 1.5 1.35
ØAL = piston Ø
1) Grease nipple, cone shape A according to DIN 71412 Notice:
2) Inside Geometry and dimensions may differ depending on
the manufacturer.
3) Dimensions may differ depending on the manufacturer
4) Nominal force applies to applications in pairs
5) m = mass per pair in kg, brackets are delivered in pairs

Trunnion mounting– bearing block CLTA–AT 4 (clampable) (dimensions in mm)
CLTA 25–100
ØAL Type Material no. Nominal ØCR CO FK FN FS ØHB KC NH TH UL l1 l2 l3 m 5)

force H7 N9 js12 max JS14 H13 +0.3 max JS14 max in kg
kN 4)
50 CLTA 25 R901071368 32 25 25 65 90 12 14 3) 5.4 26 80 110 56 45 1.5 2.4
63 CLTA 32 R901071377 50 32 25 75 110 15 18 3) 5.4 33 110 150 70 52 2 5.0
80 CLTA 40 R901071380 80 40 36 95 140 16 22 8.4 41 125 170 88 60 2.5 8.5
100 CLTA 50 R901071385 125 50 36 105 150 20 26 8.4 51 160 210 90 72 2.5 15
125 CLTA 63 R901071395 200 63 50 125 195 25 33 11.4 61 200 265 136 87 3 30
160 CLTA 80 R901071398 320 80 50 150 230 31 39 11.4 81 250 325 160 112 3.5 59
200 CLTA 100 R901071400 500 100 63 200 300 42 52 12.4 101 320 410 200 150 4.5 131
ØAL = Piston Ø
1) Grease nipple, cone shape A according to DIN 71412 Notice:
2) Inside Geometry and dimensions may differ depending on
the manufacturer.
3) Dimensions may differ depending on the manufacturer
4) Nominal force applies to applications in pairs
5) m = mass per pair, brackets are delivered in pairs

Buckling
For the admissible stroke length with flexibly guided must be interpolated. Admissible stroke length for
load and a factor of 3.5 for safety against buckling, non-guided load on request.
please refer to the relevant table. For other installation Buckling calculations are carried out according to the
positions of the cylinder, the admissible stroke length following formulas:
1. Calculation according to Euler

E Module of elasticity in N/mm2
if λ > λg
2.1 x 105 for steel
l Geometrical moment of inertia in mm4 for circular
cross-section
2. Calculation according to Tetmajer
if λ > λg v 3.5 (safety factor)

LK free buckling length in mm (depending on the
type of mounting see sketches A, B, C)
d Piston rod Ø in mm
λ Slenderness ratio
= =
Re Yield strength of the piston rod material
Influence of the type of mounting on the buckling length:

L
L
L
L
L
L
L
LK = 0,7 L LK = L LK = 2 L

Buckling
Admissible stroke length for types of mounting "MP1", "MP3", "MP5"

ØAL ØMM 70 bar 100 bar 160 bar 210 bar
in mm in mm 0° 45° 90° 0° 45° 90° 0° 45° 90° 0° 45° 90°
12 115 120 125 85 85 90 50 50 55
25
18 315 330 375 270 275 300 205 210 220 180 180 185
14 115 120 125 85 85 90 50 50 55
32
22 370 385 440 315 325 350 240 245 255 210 210 215
18 160 165 175 120 125 130 75 75 80
40 22 310 320 350 260 265 290 195 200 205 130 130 135
28 465 485 580 400 415 465 315 320 340 280 285 290
22 205 210 220 155 160 165 100 100 105
50 28 420 430 475 355 360 380 270 275 280 190 195 195
36 620 650 790 545 565 640 435 445 475 395 400 410
28 280 285 305 220 225 230 150 150 155
63 36 560 580 645 480 490 520 375 380 390 280 280 285
45 770 810 995 680 710 805 555 565 605 500 510 530
36 380 390 415 305 310 320 210 215 220
80 45 695 715 800 600 610 650 470 475 490 350 355 360
56 945 995 1225 840 870 995 685 670 745 615 625 655
45 480 495 540 390 400 420 280 285 290
100 56 850 880 1000 740 760 820 590 600 625 445 450 460
70 1150 1210 1550 1030 1075 1260 855 875 955 780 790 830
56 595 615 685 490 500 535 360 365 375
125 70 1065 1105 1290 940 965 1060 765 775 810 570 575 595
90 1445 1535 2110 1315 1380 1690 1115 1150 1285 1035 1055 1130
70 730 755 850 610 625 670 455 460 475
160 90 2) 1260 1295 1540 1105 1155 1265 910 930 975 705 780 835
110 1715 1815 2450 1565 1640 2015 1335 1380 1540 1205 1235 1320
90 945 985 1140 800 825 900 610 620 645
200 110 2) 1470 1540 1840 1310 1350 1510 1070 1090 1145 170 800 1000
140 2120 2255 2700 1955 2060 2625 1690 1755 2010 1540 1580 1725
Installation position
0° 45° 90°
1)
1)
1)
1) Admissible stroke length

2) On request

Buckling
Admissible stroke length for type of mounting "MS2"

in mm in mm 0° 45° 90° 0° 45° 90° 0° 45° 90° 0° 45° 90°
12 500 510 530 420 425 435 325 325 330
25
18 600 600 600 600 600 600 600 600 600 600 600 600
14 525 535 555 435 440 450 335 335 340
32
22 800 800 800 800 800 800 800 800 800 780 790 800
18 700 715 750 590 595 610 455 460 465
40 22 975 1000 1000 855 875 940 690 700 720 610 610 620
28 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000
22 835 850 895 705 710 730 545 550 555
50 28 855 1200 1200 1100 1130 1200 895 910 945 795 800 815
36 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200
28 1060 1086 1160 900 915 950 705 710 720
63 36 1400 1400 1400 1400 1400 1400 1185 1200 1255 1045 1055 1080
45 1400 1400 1400 1400 1400 1400 1400 1400 1400 1400 1400 1400
36 1370 1405 1525 1175 1195 1250 930 935 955
80 45 1700 1700 1700 1700 1700 1700 1460 1480 1555 1295 1305 1340
56 1700 1700 1700 1700 1700 1700 1700 1700 1700 1700 1700 1700
45 1685 1735 1910 1460 1485 1570 1165 1175 1205
100 56 2000 2000 2000 2000 2000 2000 1800 1835 1950 1595 1615 1670
70 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000
56 2075 2140 2300 1810 1845 1970 1455 1470 1515
125 70 2300 2300 2300 2300 2300 2300 2240 2290 2300 2010 2035 2120
90 2300 2300 2300 2300 2300 2300 2300 2300 2300 2300 2300 2300
70 2515 2595 2600 2200 2245 2415 1780 1800 1855
160 90 2) 2600 2600 2600 2600 2600 2600 2600 2600 2600 2600 2600 2600
110 2600 2600 2600 2600 2600 2600 2600 2600 2600 2600 2600 2600
90 2700 2700 2700 2700 2700 2700 2700 2700 2700
200 110 2) 2700 2700 2700 2700 2700 2700 2700 2700 2700 2700 2700 2700
140 2700 2700 2700 2700 2700 2700 2700 2700 2700 2700 2700 2700
0° 45° 90°

2) On request

Buckling
Admissible stroke length for type of mounting "MT4" (trunnion mounting position in cylinder center)
in mm in mm 0° 45° 90° 0° 45° 90° 0° 45° 90° 0° 45° 90°
12 190 190 200 150 150 155 105 105 105
25
18 455 470 535 395 405 435 310 315 325 275 280 285
14 195 200 205 150 155 155 105 105 105
32
22 535 555 625 460 470 510 365 365 380 320 325 330
18 265 270 290 215 215 225 150 155 155
40 22 430 445 480 360 370 385 275 280 285 230 230 235
28 670 700 825 590 605 670 475 480 505 430 435 445
22 330 335 355 265 270 280 190 195 195
50 28 570 590 645 485 495 520 375 380 390 315 315 320
36 885 925 1115 785 810 910 640 655 690 580 590 610
28 435 445 470 355 360 375 265 265 270
63 36 755 780 865 650 660 700 510 575 530 430 430 440
45 1095 1145 1390 975 1010 1140 800 815 870 725 735 765
36 585 595 630 480 485 505 340 360 365
80 45 890 920 1025 760 775 830 590 595 615 535 540 550
56 1340 1400 1700 1195 1240 1405 1000 1010 1075 885 900 940
45 725 745 805 605 615 645 415 440 475
100 56 1090 1130 1295 940 965 1045 740 750 782 675 680 695
70 1615 1700 2000 1460 1515 1770 1225 1255 1355 1115 1130 1185
56 900 925 1015 760 775 820 485 520 605
125 70 1340 1395 1640 1170 1205 1330 940 955 1000 855 865 890
90 2035 2150 2300 1860 1945 2300 1590 1635 1815 1480 1510 1605
70 1100 1300 1255 935 955 1015 730 735 760
160 90 2) 1745 1810 2090 1535 1575 1720 1255 1260 1320 1090 1115 1125
110 2410 2550 2600 2210 2315 2600 1905 1960 2180 1720 1755 1875
90 1420 1470 1680 1225 1255 1360 770 830 1020
200 110 2) 2045 2130 2530 1825 1880 2090 1505 1530 1610 1065 1140 1410
140 2700 2700 2700 2700 2700 2700 2415 2495 2700 2195 2250 2240
0° 45° 90°
1)
1)
1)

2) On request

Buckling
Admissible stroke length for type of mounting "MT2"

in mm in mm 0° 45° 90° 0° 45° 90° 0° 45° 90° 0° 45° 90°
12 130 130 135 100 100 105 65 65 65
25
18 330 340 390 285 290 315 220 225 230 195 195 200
14 135 135 140 100 100 105 65 65 65
32
22 390 405 455 335 340 370 260 260 270 230 230 235
18 180 185 200 145 145 150 95 95 100
40 22 305 315 340 250 260 270 185 190 195 155 155 155
28 485 505 600 425 435 485 335 345 360 305 305 315
22 230 235 245 180 185 190 125 125 125
50 28 410 425 465 345 350 370 260 265 270 220 220 225
36 645 675 815 570 590 665 460 470 500 420 425 440
28 310 315 335 250 250 260 180 180 180
63 36 550 565 630 465 475 505 360 365 375 305 305 315
45 800 840 1025 710 735 835 580 595 630 530 535 555
36 415 425 450 340 345 355 250 250 255
80 45 675 700 780 580 590 630 450 455 470 380 385 395
56 980 1030 1260 875 905 1030 720 735 780 645 655 685
45 515 530 575 430 435 455 320 320 330
100 56 825 855 980 710 730 795 565 570 595 480 485 500
70 1185 1245 1585 1065 1110 1300 890 915 990 815 830 870
56 640 660 730 540 550 580 410 410 425
125 70 1015 1060 1240 890 915 1010 715 725 760 615 625 640
90 1495 1580 2110 1365 1425 1735 1160 1195 1330 1080 1105 1175
70 785 810 905 665 675 720 505 515 530
160 90 2) 1315 1350 1595 1160 1210 1320 965 985 1030 760 835 890
110 1770 1870 2505 1620 1695 2070 1390 1430 1595 1260 1290 1375
90 1015 1055 1210 870 895 970 680 685 715
200 110 2) 1540 1610 1910 1380 1420 1580 1140 1160 1215 820 870 1070
140 2190 2325 2700 2025 2125 2695 1760 1825 2080 1610 1650 1790
0° 45° 90°
1)
1)
1)

2) On request

Buckling
Admissible stroke length for type of mounting "MT1"

in mm in mm 0° 45° 90° 0° 45° 90° 0° 45° 90° 0° 45° 90°
12 325 325 330 260 260 265 190 190 190
25
18 600 600 600 600 600 600 500 510 520 445 450 455
14 335 335 345 265 270 270 190 190 190
32
22 800 800 800 735 750 800 580 590 605 520 520 530
18 460 465 475 370 375 375 270 270 275
40 22 690 705 760 585 595 620 455 460 465 385 390 390
28 1000 1000 1000 945 970 1000 760 770 800 685 690 705
22 550 555 570 450 450 455 330 330 335
50 28 905 930 1015 775 790 830 615 620 630 515 520 525
36 1200 1200 1200 1200 1200 1200 1010 1025 1075 915 925 955
28 715 725 750 590 590 600 440 440 445
63 36 1175 1210 1335 1015 1035 1100 805 810 835 695 695 705
45 1400 1400 1400 1400 1400 1400 1245 1270 1345 1135 1150 1190
36 940 955 995 780 785 805 590 590 600
80 45 1465 1510 1675 1270 1300 1375 1015 1025 1055 860 865 880
56 1700 1700 1700 1700 1700 1700 1525 1555 1655 1385 1405 1460
45 1190 1210 1270 995 1005 1030 740 760 770
100 56 1790 1850 2000 1570 1600 1730 1270 1285 1330 1085 1095 1115
70 2000 2000 2000 2000 2000 2000 1900 1945 2000 1740 1765 1850
56 1480 1505 1595 1245 1260 1300 965 970 980
125 70 2190 2270 2300 1935 1990 2175 1585 1605 1675 1375 1385 1420
90 2300 2300 2300 2300 2300 2300 2300 2300 2300 2290 2300 2300
70 1805 1840 1965 1525 1545 1600 1185 1195 1210
160 90 2) 2600 2600 2600 2475 2540 2600 2065 2095 2185 1790 1885 1895
110 2600 2600 2600 2600 2600 2600 2600 2600 2600 2600 2600 2600
90 2340 2400 2610 2000 2035 2135 1575 1585 1620
200 110 2) 2700 2700 2700 2700 2700 2700 2470 2505 2625 1815 1925 2325
140 2700 2700 2700 2700 2700 2700 2700 2700 2700 2700 2700 2700
0° 45° 90°
1)
1)
1)

2) On request

Buckling
Admissible stroke length for types of mounting "ME5", "MX3", "MX5"

in mm in mm 0° 45° 90° 0° 45° 90° 0° 45° 90° 0° 45° 90°
12 510 520 540 430 435 445 335 335 340
25
18 600 600 600 600 600 600 600 600 600 600 600 600
14 535 545 565 445 450 460 345 345 350
32
22 800 800 800 800 800 800 800 800 800 790 800 800
18 710 725 755 600 605 620 465 470 475
40 22 990 1000 1000 870 890 955 705 715 735 620 625 635
28 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000
22 850 865 910 720 725 750 560 565 570
50 28 1200 1200 1200 1125 1150 1200 920 930 965 810 815 830
36 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200 1200
28 1080 1100 1170 920 930 965 720 725 740
63 36 1400 1400 1400 1400 1400 1400 1205 1225 1280 1065 1075 1100
45 1400 1400 1400 1400 1400 1400 1400 1400 1400 1400 1400 1400
36 1390 1425 1545 1195 1215 1270 950 955 975
80 45 1700 1700 1700 1700 1700 1700 1485 1510 1580 1310 1325 1360
56 1700 1700 1700 1700 1700 1700 1700 1700 1700 1700 1700 1700
45 1710 1760 1935 1480 1510 1590 1185 1195 1225
100 56 2000 2000 2000 2000 2000 2000 1815 1850 1965 1620 1635 1690
70 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000
56 2100 2165 2300 1830 1865 1990 1200 1280 1540
125 70 2300 2300 2300 2300 2300 2300 2255 2300 2300 2030 2060 2140
90 2300 2300 2300 2300 2300 2300 2300 2300 2300 2300 2300 2300
70 2540 2600 2600 2225 2275 2440 1805 1825 1885
160 90 2) 2600 2600 2600 2600 2600 2600 2600 2600 2600 2600 2600 2600
110 2600 2600 2600 2600 2600 2600 2600 2600 2600 2600 2600 2600
90 2700 2700 2700 2700 2700 2700 2360 2395 2510
200 110 2) 2700 2700 2700 2700 2700 2700 2700 2700 2700 2700 2700 2700
140 2700 2700 2700 2700 2700 2700 2700 2700 2700 2700 2700 2700
0° 45° 90°
1)
1)
1)

2) On request

Buckling
Admissible stroke length for types of mounting "ME6", "MX1", "MX2"

in mm in mm 0° 45° 90° 0° 45° 90° 0° 45° 90° 0° 45° 90°
12 195 200 220 160 160 170 115 115 120
25
18 445 465 585 395 410 475 325 330 360 295 295 310
14 205 210 230 165 170 180 120 120 120
32
22 525 550 685 465 485 560 385 390 420 345 350 365
18 270 280 315 225 230 245 165 165 170
40 22 435 455 520 375 385 420 295 300 310 245 250 255
28 645 680 895 580 605 730 485 500 555 450 460 480
22 335 350 390 280 285 305 210 210 220
50 28 580 600 700 505 515 565 400 405 425 335 340 350
36 845 895 1200 770 805 990 655 675 755 605 620 655
28 445 460 520 375 385 415 285 290 300
63 36 760 795 940 670 690 765 540 550 580 465 470 490
45 1045 1105 1400 955 1140 1240 815 845 955 765 780 835
36 590 610 690 505 515 555 390 395 410
80 45 940 980 1160 830 855 950 675 685 720 580 585 610
56 1275 1350 1700 1170 1225 1520 1005 1035 1175 930 950 1025
45 725 755 885 630 645 710 495 505 530
100 56 1145 1200 1465 1025 1060 1205 850 865 920 730 740 770
70 1530 1625 2000 1415 1485 1925 1230 1280 1485 1170 1195 1300
56 885 925 1110 775 800 900 620 635 670
125 70 1380 1450 1835 1245 1290 1500 1040 1065 1155 915 935 980
90 1900 2025 2300 1770 1875 2300 1570 1640 1980 1525 1570 1745
70 1080 1130 1370 950 985 1110 770 785 835
160 90 2) 1665 1755 2250 1515 1575 1850 1275 1310 1425 1100 1150 1250
110 2250 2395 2600 2105 2225 2600 1870 1950 2360 1780 1835 2045
90 1375 1445 1825 1225 1275 1485 1010 1035 1120
200 110 2) 1940 2050 2670 1770 1845 2200 1500 1550 1690 1250 1350 1500
140 2700 2700 2700 2605 2700 2700 2340 2450 2700 2245 2325 2660
0° 45° 90°
1)
1)
1)

2) On request

End position damping
The objective is to reduce the velocity of a moved mass, The maximum damping capacity can only be achieved
the center of gravity of which lies on the cylinder axis, when the throttle valve is closed.
to a level at which neither the cylinder nor the machine For special applications with very short stroke times, high
into which the cylinder is installed is damaged. velocities or large masses, cylinders with special end
For velocities above 20 mm/s, we recommend the use of position damping versions can be offered on request.
an end position damping feature, which absorbs energy When fixed or adjustable stops are used, special measures
without requiring the use of additional equipment. must be taken.
It must, however, always be checked whether end position
damping is also required for lower velocities with large
masses.
Series CDT3 is equipped with a progressive damping
system.
Advantages of this damping system:
▶ Progressive delay.
▶ Short damping time.
▶ Effective damping length depending on the velocity.
▶ Due to low damping pressures and no pressure peaks,
safety and the life cycle of the cylinder and the machine
are increased.
▶ Insensitive to changes in pressure,
temperature and the moved masses.
▶ Controlled end stop velocity of the piston
▶ More safety and reliability.
▶ Quick start-up due to special check valve and floating Damping capacity
bushing. When decelerating masses via the end position damping,
Cylinders with end position damping can achieve their the structural-inherent damping capacity must not be
full damping capacity only over the entire damping length. exceeded.
With the adjustable end position damping version "E", To this end, the kinetic energy and potential energy of the
a throttle valve is additionally provided when compared moved mass are to be calculated and compared to the
with version "D". End position damping version "E" admissible values from the diagram of page 50.
allows cycle times to be optimized.
Energy determination
A
A
B
B
Retraction (A): E Extension (A): E

Retraction (B): E Extension (B): E
E [Nm] Maximum value see page 50 v [m/s] Maximum velocity

[Joule] g [m/s2] 9.81
m [kg] Total moved mass including piston and rod la [m] Damping length, see page 49

Damping lengths and weights

With cylinder strokes within the damping lengths, We recommend minimum stroke greater than the damping
restrictions with regard to velocity and cycle time length plus 10 mm.
are possible.
Cylinder Ø 25 32 40 50 63
12 18 14 22 18 22 28 22 28 36 28 36 45
Head 15 15 16 16 23 23 23 22 22 22 25 25 25
Ia in mm
Base 15 15 16 16 23 23 23 22 22 22 25 25 25
m in kg Piston 0.15 0.2 0.25 0.4 0.6 0.6 0.7 0.8 1 1.2 1.4 1.7 2.0
(kg/100 mm) Rod 0.1 0.2 0.12 0.3 0.2 0.3 0.5 0.3 0.5 0.8 0.5 0.8 1.2
vmax1) (m/s) 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.4 0.4 0.4
Cylinder Ø 80 100 125 160 200

36 45 56 45 56 70 56 70 90 70 90 110 90 110 140
Head 27 27 27 28 28 28 33 33 33 36 36 36 40 40 40
Ia in mm
Base 27 27 27 28 28 28 33 33 33 36 36 36 40 40 40
m in kg Piston 2.6 3 3.6 4.7 5.3 6.3 8.0 9.2 11 16 18 20 30 34 38
(kg/100 mm) Rod 0.8 1.2 2.0 1.2 2 3.0 2.0 3 5.0 3.0 5 7.5 5.0 7.5 12
v max
1) (m/s) 0.4 0.4 0.4 0.3 0.3 0.3 0.3 0.3 0.3 0.25 0.25 0.25 0.25 0.25 0.25
The diagram on page 50 is based on the preceding 1) In case vmax is exceeded, please contact us.
table, the maximum velocities specified with closed
throttle screw.
With slower velocities, the absorbing energy decreases
according to the formula.
EU Energy absorbing
Emax Maximum energy, see characteristic curve
vU Stroke velocity
vmax Maximum speed for seal design "M"
Maximum damping time "D"; "E"
6
5
Time in s →
4
3 Ø125…20
0
2
1 Ø25…100
0
40 60 70 80 100 120 140 160
Pressure in bar →

Damping "D"; "E"
Extension Retraction
m m
100 000 100 000
10 000 Ø200 10 000 Ø200 x

90
Ø160 x
Ø160 70
Ø125 x
Ø125 56
Ø100 Ø100 x
Energy in joule →
Energy in joule →
4
1000 Ø80 1000 Ø80 x 3 5
6
Ø63 Ø63 x 2
8
Ø50 Ø50 x 2
Ø40 x 1 2
Ø40 8
100 Ø32 100 Ø32 x 1
4
Ø25 Ø25 x 1
2
10 10
1 1
0 20 40 60 80 100 120 140 160 0 20 40 60 80 100 120 140 160
Pressure in bar → Retraction Pressure in bar →
100 000 100 000
Ø200 x Ø200 x 140

10 000 110 10 000
Ø160 x Ø160 x 110
90
Ø125 x Ø125 x 90
70
Ø100 x Ø100 x 70
56
Energy in joule →
Energy in joule →
1000 Ø80 x 4 1000 Ø80 x 56

Ø63 x 35 Ø63 x 45
6
Ø50 x 2 Ø50 x 36
Ø40 x 28 Ø40 x 28
2
100 100 Ø32 x 22
Ø25 x 18
10 10
1 1
0 20 40 60 80 100 120 140 160 0 20 40 60 80 100 120 140 160
Pressure in bar → Pressure in bar →

Calculation example
When designing cylinder dimensions,

3 criteria are to be considered:
▶ Force
▶ Buckling
▶ Damping capacity
tg φ = 0,4
tg φ = 0,4
A3
mm A1
00
b5
A3 Hu
A1 m = 2200 kg
ME 6
m = 2200 kg
= 30° pr = 15 bar = 30° pk = 100 bar
pk = 100 bar pr = 15 bar
Example: Force required to move the mass

Stroke time = 2 seconds F = Frictional force plus potential energy
Load friction coefficient = tg ϕ = 0.4 (estimated) = tg ϕ • m • g • cos α + m • g • sin α
Available pressure pk = 100 bar = 0.4 • 2200 • 9.81 • 0.866 + 2200 • 9.81 • 0.5 = 18270 N
Return flow pressure pr = 15 bar = 18.27 kN
This theoretical force 18.27 kN with η = 0.79 results in
A1 Piston surface a required force = 23.13 kN and thus, a cylinder piston
A3 Annulus of piston surface diameter = 63 mm is necessary for pk = 100 bar, see page .
ϕ Surface ratio A1 / A3, see page 7
m total moved mass
Retract piston rod
v Velocity
F = Frictional force minus potential energy
la Damping length, see page 49 = tg ϕ • m • g • cos α – m • g • sin α
= 0.4 • 2200 • 9.81 • 0.866 – 2200 • 9.81 • 0.5
= – 3315 N = – 3.3 kN no force problem during
To be determined:
retraction.
Piston and piston rod diameter
Test of buckling length
Extend piston rod:
For pk = 100 bar and cylinder 63 / 28, the table
Overall efficiency η = η1 • η2
on page 47 results in a maximum admissible
η1 = cylinder efficiency = 0.9 (estimated)
stroke = 385 mm:
η2 = system efficiency
This means that the cylinder buckles.
There are 2 possibilities:
▶ Select piston rod diameter 45, maximum admissible
stroke = 1140 mm, i.e. buckling-proof
▶ Change the type of mounting, e.g. "MS2" with
a maximum admissible stroke = 915 mm
η = 0.9 • 0.88 = 0.79
1) Assuming the smallest "ϕ"

Calculation example: Test of the end position damping
Average velocity 0.5 / 2 = 0.25 m/s

Maximum velocity vu = 0.275 m/s
(estimated correction coefficient = 1.1
due to start-up and braking)
Damping capacity required for piston rod extension:
No damping problem for piston rod extension.
Damping capacity required for piston rod retraction:
Diagram on page 50 results in 445 joules for

pk = 100 bar and vmax = 0.4 m/s, i.e. the cylinder
can absorb energy for 0.275 m/s (see page 49):
So the cylinder cannot absorb the necessary

damping capacity: you have to select the
next larger diameter 80/56.

Selection criteria for seals
Working conditions
Hydraulic fluid temperature Seal versions
Hydraulic fluid
range "M" "T" "S"
HL, HLP –20 °C … +80 °C ++ ++ ++
HFA +5 °C … +55 °C +/– ++ +/–
HFC –20 °C … +60 °C – ++ –
HFDR –15 °C … +80 °C – – ++
Environmental conditions
Seal versions
Ambient and rod temperature in the area of the piston rod
"M" "T" "S"
Standard –20 °C … +80 °C 1) ++ + ++ 2)
Extended +80 °C … +120 °C 1) – – ++
++ = very good + = good +/– = conditional, depending on the application parameters – = inappropriate
General technical data in corresponding data sheets will

remain valid, see page 5.
1) Moreover, observe the corresponding hydraulic fluid

temperature range
2) Lower temperature limit –15 °C
Notice:
Generally, a hydraulic fluid temperature of approx. 40 °C
is recommended. The specified values are to be regarded
as guidelines; depending on the case of application,
it may be necessary to check the suitability of the seal system.

Seal kits
Seal kit complete

ØAL ØMM Material number
in mm in mm "M" "T" "S"
12 R961008000 R961008026 R961008052
25
18 R961008001 R961008027 R961008053
14 R961008002 R961008028 R961008054
32
22 R961008003 R961008029 R961008055
18 R961008004 R961008030 R961008056
40 22 R961008005 R961008031 R961008057
28 R961008006 R961008032 R961008058
22 R961008007 R961008033 R961008059
50 28 R961008008 R961008034 R961008060
36 R961008009 R961008035 R961008061
28 R961008010 R961008036 R961008062
63 36 R961008011 R961008037 R961008063
45 R961008012 R961008038 R961008064
36 R961008013 R961008039 R961008065
80 45 R961008014 R961008040 R961008066
56 R961008015 R961008041 R961008067
45 R961008016 R961008042 R961008068
100 56 R961008017 R961008043 R961008069
70 R961008018 R961008044 R961008070
56 R961011580 R961011587 R961011595
125 70 R961011581 R961011588 R961011596
90 R961011582 R961011589 R961011597
70 R961011583 R961011590 R961011598
160 90 1) R961014437 R961014440 R961014443
110 R961011584 R961011591 R961011599
90 R961011585 R961011592 R961011601
200 110 1) R961014438 R961014441 R961014444
140 R961011586 R961011593 R961011602
1) On request

Tightening torques
Tie rod nut

Tightening torques in Nm for types of mounting
ØAL ØMM
"ME5", "ME6", "MP1"; "MP3", "MP5", "MS2"
in mm in mm "MX1", "MX2"
"MT1", "MT2", "MT4", "MX3", "MX5"
12
25 5.5 4
18
14
32 8 6
22
18
40 22 20 15
28
22
50 28 50 37
36
28
63 36 60 45
45
36
80 45 125 90
56
45
100 56 190 140
70
56
125 70 400 300
90
70
160 90 1) 800 600
110
90
200 110 1) 1250 900
140
1) On request

Components
1 2 3 4 5 6 7 8 6 9 10 11
B A
Piston rod seals Piston seals
Ø 25 … 32 and Ø 40/18 "M", "T", "S" for piston Ø 25 ... 63
„M“
„T“, „S“
Ø 40/22, Ø 40/28 and Ø 50 ... 200 "M", "T", "S" for piston Ø 80 ... 200
„M“
„T“, „S“
A Piston chamber
B Annulus area
1 Piston rod
2 Guide socket
3 Piston rod seal
4 Cylinder head
5 Cylinder pipe
6 Damping bush
7 Piston
8 Piston seal
9 Cylinder base
10 Nut
11 Tie rod

Priming / painting
Priming | By default, hydraulic cylinders are primed Painting | By default, hydraulic cylinders can be ordered
with a coating (color gentian blue RAL 5010) in the CP4 corrosivity category in the RAL colors.
of min. 40 μm. Other colors on request. The following surfaces of cylinders and attachment parts
The following surfaces of cylinders and attachment parts are not painted
are not primed: ▶ All fit diameters and connection surfaces to
▶ All fit diameters to the customer side the customer side
▶ Sealing surfaces for line connection ▶ Sealing surfaces for line connection
▶ Sealing surfaces for flange connection ▶ Sealing surfaces for flange connection
▶ Connection surface for valve mounting ▶ Connection surface for valve mounting
▶ Measuring coupling ▶ Measuring coupling
▶ Spherical / plain bearing ▶ Spherical / plain bearing
▶ Grease nipples ▶ Grease nipples
Notice:
Surfaces not primed or painted are protected with solvent-free
corrosion protection agent. Accessories ordered as a separate
order item are not primed or painted by default.
Corresponding priming and/or painting on request.
Corrosivity categories
Applications
Class Requirements
Inside Outside
240 h salt spray test SST Field of application, e.g. Not suitable for outdoor
(DIN EN ISO 9227) Hall atmosphere, exposure.
Priming CP3 240 h condensation water test KKT Air humidity ≤ 60%,
(DIN EN ISO 6270-2) no thermal load.
Layer thickness: min. 40 μm
480 h salt spray test SST. Unheated buildings in which there Urban and industrial
(DIN EN ISO 9227) may be condensation (production atmosphere with little
Painting CP4 480 h condensation water test KKT rooms, storage and sport halls). salt or sulfur dioxide load.
(DIN EN ISO 6270-2)
Nominal layer thickness: 120 μm
In this connection, observe the information on the

color set-up on page 5.
The specified resistances of the individual Bosch Rexroth
classes only refer to the primed and painted cylinder areas,
not, for example, to piston rods, trunnion mounting, etc.
In this connection, special measures may be necessary.

Project planning / maintenance instructions

Boundary and application conditions: Check lists for hydraulic cylinders
▶ The mechanical alignment of the movement axis and Cylinders the characteristics and/or application
thus the mounting points of hydraulic cylinder and parameters of which deviate from the values specified
piston rod must be ensured. Lateral forces on the in the data sheet can only be offered as a special
guides of piston rod and piston are to be avoided. version upon request. For offers, the deviations of the
It may be necessary to consider the own weight of the characteristics and / or application parameters must be
hydraulic cylinder ("MP1", "MP3", "MP5", "MT1", "MT2" described in the check lists for hydraulic cylinders (07200).
or "MT4") or the piston rod.
Stroke tolerances
▶ The buckling length / buckling load of the piston
According to ISO 6020-2, a stroke tolerance of +2 mm is
rod and / or the hydraulic cylinder must be observed
admissible for strokes up to 1250 mm; the stroke tolerance
(see page 40).
for cylinder strokes over 1250 mm to 3000 mm is +5 mm.
▶ The maximum admissible stroke velocities with regard
A tolerance of ±0.3 mm is possible as option, smaller
to the suitability / load of seals must be observed as
tolerances are not reasonable for tie rod cylinders.
must their compatibility with the properties of the
hydraulic fluid (see page 53). Minimum strokes
▶ The maximum admissible velocities / kinetic energies For type of mounting "MT4", the minimum stroke is
when moving into the end positions, also considering to be observed due to the trunnion mounting width,
external loads, must be observed (excess pressure). see page 6.
▶ The maximum admissible operating pressure When using end position damping, the minimum
must be complied with in any operating state stroke must also be observed, see page 48.
of the hydraulic cylinder. Support width extension and tie rod support are possible
Possible pressure intensification resulting from upon request.
throttling points is to be observed. Line connections
▶ Detrimental environmental influences, like e.g. aggressive The cylinders of series CDT3 are supplied with pipe
finest particles, vapors, high temperatures, etc. as well thread or enlarged pipe thread according to ISO 1179-1
as contamination and deterioration of the hydraulic fluid or metric ISO thread according to ISO 6149-1.
are to be avoided.
Standards
The installation dimensions and types of mounting
Notice:
of the hydraulic cylinders comply with ISO 6020-2.
This list does not claim to be complete. In case of questions
Acceptance regarding the compatibility with the medium or exceedance of
Every hydraulic cylinder is tested according to Rexroth the boundary or application conditions, please contact us.
standards and following ISO 10100: 2020 with module L. All graphical pictures in the data sheet are examples.
Safety instructions The product supplied may therefore differ from the figure shown.
For assembly, commissioning and maintenance of

hydraulic cylinders, observe the operating instructions
07100-B. Service and repair work has to be performed
by Bosch Rexroth AG or by personnel especially trained
for this purpose. No warranty is accepted for damage as
a consequence of assembly, maintenance or repair
work not performed by Bosch Rexroth AG.

Project planning software ICS (Interactive Catalog System)
The ICS is a selection and project planning aid for quickly and reliably gets the exact technical data of the
hydraulic cylinders. The ICS allows designers for machines selected component as well as 3D CAD data in the
and systems to quickly and reliably find the perfect correct file format for all common CAD systems.
hydraulic cylinder solution through logic-guided type key This allows users to reduce costs while increasing
enquiries. This software helps to solve design and project their competitiveness.
planning tasks more quickly and efficiently. After having Online: www.boschrexroth.com/tie-rod-cylinder
been guided through the product selection, the user

Notes
Bosch Rexroth AG © All rights reserved to Bosch Rexroth AG, also regarding any disposal,
Industrial Hydraulics exploitation, reproduction, editing, distribution, as well as in the event of
Zum Eisengießer 1 applications for industrial property rights.
97816 Lohr am Main, Germany The data specified above only serve to describe the product. No statements
Phone +49 (0) 93 52 / 40 30 20 concerning a certain condition or suitability for a certain application can be
my.support@boschrexroth.de derived from our information. The information given does not release the user
www.boschrexroth.de from the obligation of own judgment and verification.
It must be remembered that our products are subject to a natural process of
wear and aging.

Re 17051 - 2022-04

Uploaded by

Copyright:

Available Formats

Re 17051 - 2022-04

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Re 17051 - 2022-04

Uploaded by

Copyright:

Available Formats

▶ Installation dimensions according to ISO 6020-2 and Features1

04 Piston Ø (ØAL) 25 … 200 mm

05 Piston rods Ø (ØMM) 12 … 140 mm 3)

08 Component series 30 … 39 (30 … 39: Unchanged installation and mounting dimensions) 3X

Line connection − version

According to ISO 1179-1 (enlarged pipe thread) S 5)

Line connection − position at head (see page 31)

Line connection − position at base (see page 31)

Hardened and hard chromium-plated H

Bosch Rexroth AG, RE 17051, edition: 2022-04

Piston rod end (see page 10 … 27)

With trunnion T 12)

End position damping (see page 48 … 52)

Seal design (selection criteria for seals, see page 53)

Hydraulic fluid filling

21 Further details in the plain text

RE 17051, edition: 2022-04, Bosch Rexroth AG

Bosch Rexroth AG, RE 17051, edition: 2022-04

Hydraulic fluid Classification Data sheet

1) See page 53.

RE 17051, edition: 2022-04, Bosch Rexroth AG

Line connection Maximum Line connection Maximum

Information on stroke length and stroke velocity

Bosch Rexroth AG, RE 17051, edition: 2022-04

Areas, forces, flow (for operating pressure up to 210 bar)

qV3 qV1 qV2

1) Theoretical static cylinder force 2) Stroke velocity

RE 17051, edition: 2022-04, Bosch Rexroth AG

Weight for cylinder (in kg)

Swivel head, clevis bracket and trunnion mounting

Bosch Rexroth AG, RE 17051, edition: 2022-04

Overview of types of mounting (for operating pressure up to 210 bar)

„ME5“ according to DIN/ISO/NF „MT1“ according to ISO/NF „MX5“ according to NF

„ME6“ according to DIN/ISO/NF „MT2“ according to ISO/NF

„MP5“ according to DIN/ISO/NF „MX1“ according to ISO/NF

„MS2“ according to DIN/ISO/NF „MX2“ according to ISO/NF

„MT4“ according to DIN/ISO/NF „MX3“ according to ISO/NF

„MP1“ according to ISO/NF

„MP3“ according to ISO/NF

RE 17051, edition: 2022-04, Bosch Rexroth AG

Dimensions: Rectangular flange at head "ME5"

1 ... 4 = Position of the line connections "X"

Position of the line Position dimension "H"

Bosch Rexroth AG, RE 17051, edition: 2022-04

Dimensions: Rectangular flange at head "ME5"

ØAL E Line connection "B" Line connection "R" GA H 7) J PJ 8) PJ 9) WF WH Y 8) Y 9)

RE 17051, edition: 2022-04, Bosch Rexroth AG

Dimensions: Self-aligning clevis at base "MP5"

1 ... 4 = Position of the line connections

Bosch Rexroth AG, RE 17051, edition: 2022-04

Dimensions: Self-aligning clevis at base "MP5"

ØAL E Line connection "B" Line connection "R" GA H 8) J PJ WH Y

ØAL = Piston Ø 4) Grease nipple M6 DIN 71412 from piston Ø 40 mm

RE 17051, edition: 2022-04, Bosch Rexroth AG

Dimensions: Foot mounting "MS2"

1 ... 4 = Position of the line connections

25 12 4) 3 4) 19 6.6 72 8.5 54 72 33 114 138 154 18 28.5

▶ Installation dimensions according to ISO 6020-2 and Features1

Dimensions: Rectangular flange at head "ME5"

Dimensions: Rectangular flange at head "ME5"

Dimensions: Trunnion mounting at head "MT1"

Dimensions: Trunnion mounting at head "MT1"

Dimensions: Extended tie rod at base "MX2"

Dimensions: Extended tie rod at base "MX2"

Dimensions: Clevis at base "MP1"

Dimensions: Clevis at base "MP1"