TMS 850

Product Guide

HYDRAULIC TRUCK CRANE

Features
n
MAX CAPACITY (Outriggers) - 50 Tonnes at n
MAX. ROAD SPEED - 50 km/hr.
2.5m Radius (85% Rating) 360° Slew n
CARRIER - 8x4 Drive
n
BOOM - 5 Section formed full power boom 11.0m - 41.3m
10.1m Fixed lattice extension (optional)
 Superstructure Specifications

BOOM HYDRAULIC SYSTEM

5-section, telescopic, formed, full power, sequenced- Pump - 3 Sec gear pump driven through gear box PTO
synchronized boom. Fabricated from high strength low Engine driven steering pump.
alloy steel plates. Telescopic sections slide on adjustable Valves - 3 nos. Over centre control valves with built-in
and replaceable low friction wear resistant pads. pressure relief.
Telescoping Range: 11m - 41.3m
Filter - Return line type, full flow with by pass protection
Maximum Tip Height: 44m
and service indicator. Replaceable cartridge.
BOOM NOSE Reservoir - 715 liters capacity fitted with filter, external
Five nylatron sheaves mounted on heavy duty tapered sight gauge, clean out access, strap mounted to frame.
roller bearings with removable pin-type rope guards.
Oil Cooler - Remote mounted, thermostatically controlled
BOOM ELEVATION electric motor driven fan.
Single double acting hydraulic cylinder with integrated
LOAD MOMENT INDICATOR & ANTI-TWO BLOCK
holding valve.
SYSTEM
BOOM ANGLE Electronic load moment indicator system with audio- visual
Maximum 78°, Minimum -1.5° warning & control lever lock out indicates electronic display
SUPERSTRUCTURE FRAME of boom angle, length, radius, relative load moment,
Fabricated from high tensile steel plates and sections. permissible load, load indication & warning of impending
two block condition. Motion cut off to ensure the safe
SLEW SYSTEM
operation with load for tele, derrick & hoist motions.
Ball bearing swing circle with 360° continuous rotation.
Planetary “Glide-Swing” with foot applied multi-disc SAFETY SYSTEM
wet brake. Spring applied hydraulically released parking Pendent Limit Switch on boom head for over hoist. Third
brake. Mechanical house lock operated from cab. Free wrap indicator on hoist barrel to ensure 3 turns of rope
slew facility provided. on hoist drum. Hydraulic relief valves to protect pumps
and structures from excessive pressure. Lock and counter
SLEW SPEED
balance valves fitted on derrick, telescopic and outrigger
Limited to 2 rev./min. (Un-laden) for controlled operation.
cylinders to sustain rams in the event of hydraulic failure.
HOIST SYSTEM
OPERATOR’S CAB
Power up and down, equal speed, planetary reduction
with integral automatic spring applied multi disc brake Totally enclosed steel construction, full vision type,
on grooved hoist barrel. Hoist drum fitted with third wrap windows fitted with toughened safety glass including
indicator. front windscreen. Adjustable operator’s seat, cab interior
Maximum Single Line Pull: Hoist Drum light, electric fan, electric horn, electric windshield wiper
1st layer - 7950kg, 2nd layer - 7250kg, and lockable sliding door. Ergonomically designed cab
3rd layer - 6700kg, 4th layer - 6200kg and controller layout to give fatigue free comfort to the
Maximum Single Line Pull - Hoist Rope : 6500kg operator.
Maximum Single Line Speed: OPTIONAL EOUIPMENT
100 m/min (Unladen) - Top layer Auxiliary Hoist Unit
Non Spin Hoist Rope: 19mm (3/4”) dia & length 182m Air Conditioned super cabin
HOOK-BLOCK Air Conditioned carrier cabin
50T, 4 sheaves. 10.1m Fixed Lattice
15T Single Sheave Hook Block (Loose Supply)
COUNTER WEIGHT
6.8T Headache Ball
6000kg pinned with superstructure.
Tie Down Rope
TMS 850

CRANE CONTROLS Anemometer

Joystick controls are in operator’s cab for slewing, 5 Kg Fire Extinguisher
telescoping, hoisting and derricking with independent or Auxiliary Boom Nose
simultaneous operation of crane motions.

Technical Specification TIL/TMS850/1121

Height of Lift : 5 Section 11.0m - 41.3m Full Power Boom
10.1m Fixed Lattice Extension

WORKING RANGE DIAGRAM

(BOOM DEFLECTION NOT SHOWN)

BOOM & EXTENSION LENGTH IN METRES

HEIGHT FROM GROUND IN METRES

OPERATING RADIUS FROM AXIS OF ROTATION IN METRES

TMS 850

NOTE:
The above heights of lift and boom angles are based on a straight (unladen) boom and
allowance should be made for boom deflections obtained under laden conditions.

Technical Specification TIL/TMS850/1121

 Lifting Capacities (Metric) 85% Rating
5 Section Boom Duties (in Kilograms)

Main Boom Duties on Outriggers Fully Extended - Full 360° Slew

Radius Main Boom Length (in Meters)
in
Meters 11.0 12.2 15.2 18.3 21.3 24.4 27.4 30.5 33.5 36.3 39.0 41.3

2.5 50000
3.0 45000 36525 30500
3.5 41000 36050 29475 25425
4.0 36425 34250 28375 24700
4.5 31950 31875 27325 23625 20500
5.0 28950 29175 26100 22550 19650
6.0 23425 23625 23550 20375 17675 15625 14225
6.5 20750 20500 20500 18875 17250 15000 13750
7.0 19600 19850 20050 18875 16500 14375 13125 9525 8320
8.0 14675 16700 16925 17050 15000 13125 12000 9525 8060 7750
9.0 14250 13900 13650 13200 12100 10900 9525 7265 6900 6200 5000
10.0 9285 11100 10900 11350 11000 9750 9050 6595 6200 5000 4300
12.0 7400 7250 7650 8000 8300 7350 5530 5000 4300 3500
14.0 4900 5350 5700 5925 6150 4720 4300 3500 3000
16.0 3250 3725 4000 4325 4525 4080 3750 3000 2750
18.0 2500 2850 3100 3325 3480 3000 2750 2400
20.0 1950 2200 2400 2550 2650 2400 2200
22.0 1100 1400 1650 1825 1940 2000 2000
24.0 750 1000 1200 1300 1400 1500
26.0 500 650 800 900 1000

28.0 500 500

Note : Minimum boom angle 0 degree for 41.3 meter boom length (no load) at over rear only
WARNING - Do not derrick-up from 0 degree boom angle if boom length is more than 33.5 meter

10.1m Fixed Offset Extension - 360° Duties in Kilograms

Radius 10.1m length

(in Meters) 0° Offset 25° Offset 45° Offset

12.0 3875
14.0 3875
16.0 3875 3375
18.0 3780 3260 2965
20.0 3170 3005 2840
22.0 2420 2390 2300
24.0 1820 1790 1700
TMS 850

26.0 1310 1280 1200

28.0 890 860 770
30.0 530 500 420

Technical Specification TIL/TMS850/1121

Notes

Weight Reductions For Load Handling Devices

Auxiliary Boom Nose 59 kg.

Hook Blocks and Headache Ball

50 MT 4 Sheaves **426 kg.

15 MT 1 Sheave **295 kg. Hookblock Capacities and Weights - Tonnes

6.8 MT Headache Ball **130 kg.
No of Falls 8 7 6 5 4 3 2 1
10.1 M Boom Extension
Permissible Load 50 44 37.7 31.5 25.2 19 12.75 6.5
Stowed (Boom Extension) *470 kg.

Erected (Boom Extension) *2195 kg. Weight of Hook block 0.426 0.426 0.426 0.426 0.426 0.426 0.295 0.13

*Reduction of main boom capacities

** Refer to the rating plate for actual weight.

Notes for Lifting Capacities

WARNING: THIS CHART IS ONLY A GUIIDE. The 7 The machine is equipped with front jack, the
Notes below are for illustration only and should not front jack cylinder shall be set along with the four
be relied upon to operate the crane. The individual outriggers.
crane’s load chart, operating instructions and other
8 Tyres shall be inflated to the recommended pressure.
instruction plates must be read and understood
prior to operating the crane. Damaged tyres are hazardous for safe operation of
crane.
1 All rated loads have been tested to meet minimum
requirements of IS: 4573-1982 Specification for 9 Lifting over-side on rubber is not permitted Outrigger
Power Driven Mobile Cranes, and do not exceed beams must be fully extended and stabilizers
(85% of the tipping load on outriggers as well as properly set when rotating super structure over the
on rubber) as determined by SAE J765 OCT 80 side.
Crane Stability Test Code. 10 Load ratings are based on freely suspended
2 The weight of hook-block, slings and all similarly loads. No attempt shall be made to move a load
used load handling devices must be added to the horizontally on the ground in any direction.
weight of the load. When more than minimum 11 Do not travel with crane boom extension or jib
required reeving is used the additional rope weight erected.
shall be considered part of the load.
12 Handling of other equipment with the boom is not
3 Capacities appearing above the bold line are based authorized except with equipment furnished and
on structural strength and tipping should not be installed by TIL Ltd.
relied upon as a capacity limitation.
13 10.1m Fixed Extension length may be used for
4 All capacities are for crane on firm, level surface. It single line lifting service only.
may be necessary to have structural supports under
the outrigger floats or tyres to spread the load to a WARNING: 10.1m Fixed offsetable boom extension.
larger bearing surface. For main boom length greater than 33.5m with
10.1m fixed boom extension in working position,
5 When either boom length or radius or both are the boom angle must not be less than 40°, since loss
between values listed, the smallest load shown at of stability will occur causing a tipping condition.
either the next larger radius or boom length shall The boom angle is not restricted for main boom
be used. length equal to or less than 33.5m. This warning
TMS 850

6 For outrigger operation, all outriggers shall be fully also applies for boom extension erection purposes.
stretched & jacks extended to raise tyres free of
the ground & the slew plinth becomes horizontal
before raising the boom or lifting loads.

Technical Specification TIL/TMS850/1121

 Carrier Specfication

CARRIER FUEL TANK

8x4 wheel right hand drive, purpose built heavy duty Capacity - 300 liters
carrier frame of torsion box section with integral front
WHEELS & TYRES
& rear outrigger housing fabricated from high strength
Tyres 11.00 x 20 - 16PR single on front axles and twins
steel plates and sections.
on rear axles.
OUTRIGGERS Spare wheel (one) provided for front axle.
Hydraulically operated outrigger system comprising four
independently controlled hydraulic telescopic horizontal DRIVER’S CAB
beams with vertical jacks for over side & over rear operation. Two man design, steel construction full width cab with
Plus one vertical hydraulic jack mounted under front of electric fan, interior light, horn, operating windows
carrier to permit 360° lifting duties. Outrigger hydraulic fitted with toughened glass. Two lockable doors, electric
jacks are fitted with positive lock valves. Easy fit outrigger windscreen wiper in front of windscreen. Upholstered
feet are provided with stowage facility on carrier. and adjustable operator’s seat. Automotive controls,
including steering wheel, pedals for clutch, brake and
OUTRIGGER CONTROLS
accelerator.
Located in the superstructure cab on front dash panel as
well as on both side of the chassis. Crane level indicator INSTRUMENTATION
adjacent to controls Air pressure gauge, engine oil pressure gauge, fuel gauge,
ENGINE water temperature gauge, speedometer, voltmeter, tacho-
Heavy duty, water cooled, turbocharged, intercooler hourmeter, warning lights and switches for control.
diesel engine of adequate horse power, ELECTRICAL EQUIPMENT
Emission : BS IV CEV 24-Volt starting and lighting system includes two
CLUTCH combined dipping head lamps, side, rear and stop lamp,
Dry single plate hydraulically operated. flashing direction indicator.

GEAR BOX MISC. STANDARD EQUIPMENT

ZF Synchromesh, 9 forward & 1 reverse speed obtained Beacon Lights
via a single lever control. 3 point seat belt in driver’s cab
Boom base light
DRIVE CONFIGURATION
Front and Rear Tow Hook
8x4
Mobile charging point in driver’s cabin
AXLES 1 no. Fire Extinguisher
Front Axle - 2 beam type non-drive steer axles, leaf spring First-Aid box
mounted in tandem. Full Deck Platform
Rear Axle - 2 Heavy duty, fully floating type with hub Lockable Tool Box
reduction, twin axle. Air operated inter-axle differential Tool Box with Tool Kit for normal maintenance
lock. Mounted on specially designed rocker beam to
allow maximum articulation on uneven ground. MAXIMUM SPEED
50 km/hr.
STEERING
Front axles, mechanical with hydraulic power assist GROSS VEHICLE WEIGHT AND AXLE LOADS
controlled by steering wheel from driver’s cab (approx)
Turning Circle Diameter - 23.2m Front Axles – 15,490 kg
Rear Axles – 24,000 kg
BRAKES
GVW – 39,490 kg
Service - Air operated on all wheels by means of foot
operated pedal in driver’s cab. Optional Weights (approx.)
TMS 850

Parking - Flick-valve operated, spring actuated Fixed Lattice : 800 kg

pneumatically released brake on trailing front axle and Auxiliary Hoist : 700 kg
leading rear axle.

Technical Specification TIL/TMS850/1121

GA Drawing

Auxiliary Hoist
(Optional)

Dimensions in mm

Constant improvement and engineering progress make it necessary that we reserve the right to make specification, equipment and price changes without notice. The
photographs/drawings in this document are just for Illustrative purpose which may include optional equipment and accessories, which can be provided at an additional
cost on request.
TMS 850

Technical Specification TIL/TMS850/1121

TIL Limited
CIN: L74999WB1974PLC041725
Registered & Corporate Office:
1, Taratolla Road, Garden Reach, Kolkata - 700024
Phone: + 91 33 2469 3732-6 / 6497 | 6633 2000 / 2845
Fax: + 91 33 2469 2143 / 3731
Email: Mhg.Er@tilindia.com | mktg-til@tilindia.com

CHENNAI
TIL Limited
Jhaver Plaza, 7th Floor 1-A
Nungambakkam High Road
Chennai 600 034, Tamil Nadu
Phone: +91 44 6670 3000 / 3010
Fax: +91 44 2827 9681
Email: chennai.til@tilindia.com

DELHI NCR
Plot 11, Site No.IV
Sahibabad Industrial Area
Ghaziabad 201 010 U.P.
Phone: +91 120 277 8735 / 8736 / 7468
Fax: +91 120 277 7467
Email: MHGMarketing.Sahibabad@tilindia.com | mhgcs.Sahibabad@tilindia.com

DELHI
TIL Limited
302 Ansal Bhawan
16, Kasturba Gandhi Marg, New Delhi 110 001
Phone: +91 11 2331 1607 / 8046 / 9248 | 2335 0250 / 0255
Fax: +91 11 2331 3263
Email: til.delhi@tilindia.com

KAMARHATTY
TIL Limited
517, Barrackpore Trunk Road
Kolkata 700 058
Phone: +91 33 2553 1352 / 1882 | 6633 4000
Fax: +91 33 2553 2546 / 5971
Email: MktDept.KMT@tilindia.com | til.kmt@tilindia.com

KHARAGPUR
TIL Limited
Vill. & P.O. Changual, Kharagpur
Dist: Paschim Medinipur 721 301, West Bengal TIL has a pan-India network of offices with service
Phone: +91 32 2266 1101
engineers located in the close proximity of jobsites.
MUMBAI
TIL Limited
A - 606, A Wing, 6th Floor, Toll Free No: 1800 266 1535
215 Atrium, Andheri - Kurla Road,
Andheri (East), Mumbai 400059, Maharashtra www.tilindia.in
Phone: + 91 22 4969 1169
Mobile: +91 8850971609
Email: Mumbai.TIL@tilindia.com | Mumbai.Custsupp@tilindia.com Technical Specification TIL/TMS850/1121. This cancels Technical Specification TIL/TMS855/0317.

This document is non-contractual. Constant improvement and engineering progress make it necessary that we reserve the right to make specification, equipment,
and price changes without notice. Illustrations shown may include optional equipment and accessories and may not include all standard equipment.
Copyright © 2021 TIL Limited. All Rights Reserved