TM 35100

TM-35100
31.7 Metric Ton Capacity (35 US Ton)

HYDRAULIC CRANE

DIMENSIONS

Specifications are subject to change without notice.

-1-
CRANE SPECIFICATIONS
BOOM CAB AND CONTROLS
Four section full power synchronized telescoping boom, Left side, 1 man type, steel construction with sliding door
9.35~30.5m (30.7'~100'), of round box construction with access and tinted safety glass windows opening at side. Door
4 sheaves, 0.336m (13-1/4") pitch diameter, at boom head. window is power controled. Windshield glass window and roof
The synchronization system consists of a telescope cylinder, glass window are shatter-resistant. Adjustable control lever
extension cables and retraction cables. Hydraulic cylinder stands for slew, boom elevation, boom telescoping and hoist.
fitted with holding valve. Boom telescope sections are Control lever stands can change neutral positions and tilt for
supported by wear pads both vertically and horizontally. easy access into cab. 3 way adjustable operator's seat with
Extension speed 21.15m (69.3') in 75sec. high back, headrest and armrest.
Internal anti-two-block device cable. Engine throttle knob. Foot operated controls: boom elevation,
boom telescoping and engine throttle.
BOOM ELEVATION - By a double acting hydraulic cylinder Hot water cab heater and air conditioning.(OPTIONAL)
with holding valve. Elevation -8o~79.5o. Boom angle indicator. Dash-mounted engine start/stop, monitor lamps, cigarette
Automatic speed reduction and slow stop function. lighter, front washer and wiper switch, outrigger controls,
Elevation speed -8o~79.5o in 45sec. power window switch, slewing brake switch, free slew/ lock
slew selector switch and ashtray.
JIB - Two stage lattice type with 5o ,25oor 45o offset (tilt type). Correct jib status select switch. Upper console includes roof
Single sheave, 0.368m (14-1/2") pitch diameter, at jib head. wiper switch, emergency outrigger set up key switch.
Box type top section telescoped from lattice type base section Instruments - Hydraulic oil pressure is monitored and displayed
which stows alongside base boom section. Jib length is on the AML-L display panel.
8.6~15.2m (28.2'~50')
Tadano electronic LOAD MOMENT INDICATOR system
ANTI-TWO-BLOCK DEVICE - Pendant type over-winding cut out (AML-L) including:
device with audio/visual warning system.  Control lever lockout function.
 Load radius / boom angle / tip height / slew range
SLEW preset function
Hydraulic axial piston motor driven through planetary slew  Warning buzzer
speed reducer. Continuous 360o full circle slew on ball bearing  Boom angle / boom length / jib offset angle / load radius /
turntable at 2.8rpm. Equipped with manually locked/released rated lifting capacities / actual loads read out
slewing brake. Twin slew system: Free slew or lock slew  Ratio of actual load moment to rated load moment indication.
controlled by selector switch on right hand of side console.  Automatic speed reduction and slow stop function on
boom elevation and slew (slew range restricted only)
HOIST  Working condition register switch
 External warning lamp (OPTIONAL）
MAIN HOIST - Hydraulic axial piston motor driven through winch TADANO AML-L monitors outrigger extended length and
speed reducer. Power load lowering and raising. Equipped with automatically programs the corresponding "RATED LIFTING
automatic brake (neutral brake) and counterbalance valve. CAPACITIES" table.
Equipped with cable follower and drum rotation indicator.
OUTRIGGERS - Four hydraulic, three-section beam and jack
DRUM - Grooved 0.32m (12-5/8") root diameter x 0.535m (21") outriggers. Vertical jack cylinders equipped with integral holding
wide. Wire rope: 130m of 16mm diameter rope (426' of 5/8"). valve. Each outrigger beam and jack is controlled independently
Drum capacity: 219.5m (720') 6 layers. Maximum line pull from either side of carrier or crane cab. Beams extend to
(permissible): 5,710kg. (12,600lbs)*. Maximum line speed: 7.2m (23' 7-1/2") center-line and retract to within 2.44m (8')
140m/min (459FPM). overall width. Controls and sight bubble located on both side of
* Maximum permissible line pull may be affected by wire rope carrier and in the crane cab. Three outrigger extension lengths
strength. are provided with corresponding "RATED LIFTING CAPACITIES"
for crane duty in confined areas.
HOOK BLOCKS Min. extension 2.2m (7' 2-5/8") center to center
31.7 metric ton-4 sheaves with swivel hook and safety latch, Mid. extension 5.54m (18' 2-1/8") center to center
for 16mm (5/8") wire rope. (OPTIONAL) Max. extension 7.2m (23' 7-1/2") center to center
4 metric ton-weighted hook with swivel and safety latch, for
16mm (5/8") wire rope. Float size(Diameter) 0.61m (24")

HYDRAULIC SYSTEM
PUMPS - Two variable piston pumps for crane functions. FRONT STABILIZER - A fifth hydraulically operated outrigger jack.
Tandem gear pump for slew and outriggers. Powered by carrier Mounted to the front frame of carrier. Hydraulic cylinder equipped
engine. Pump disconnect for crane is engaged/ disengaged by with integral holding valve and steel float.
rocker switch from carrier cab.
CONTROL VALVES - Multiple valves actuated by pilot pressure ELECTRICAL SYSTEM - Power supply : DC12Ⅴ
with integral pressure relief valves.
RESERVOIR - 358 lit. (94.5 gallon) capacity. External sight level
gauge.
FILTRATION - 26 micron return filter, full flow with bypass NOTE: Each crane motion speed is based on unladen conditions.
protection, located inside of hydraulic reservoir. Accessible for
easy replacement.
OIL COOLER - Air cooled fan type.

-2-
STANDARD EQUIPMENT OPTIONAL EQUIPMENT
FOR SUPERSTRUCTURE
- Four section full power synchronized boom 9.35 m~30.5 m - 31.7 metric ton 4 sheaves hook block
(30.7'~100') internal anti-two-block device cable. - Hot water cab heater and air conditioner (Upper cab).
- 8.6 m~15.2 m (28.2'~50') lattice jib (tilt type) with 5o , - Radio remote controls
25o or 45o pinned offsets. - Two-person basket
- Boom angle indicator - One-person basket
- Main hoist with grooved drum, cable follower and 130m of 16mm
(426' of 5/8") cable.
- Drum rotation indicator main hoist.
- Anti-two-block device
- Tadano electronic load moment indicator system
(AML-L) including
- Control lever lockout function.
- Load radius / boom angle / tip height / swing range
preset function.
- Warning buzzer
- Boom angle / boom length / jib offset angle / load
radius /rated lifting capacities / actual loads read out
- Ratio of actual load moment to rated load moment
indication.
- Automatic speed reduction and slow stop function
on boom elevation and slew.
- Working condition register switch
- External warning lamp(OPTIONAL)
- Outrigger extension length detector
- Tadano twin slew system
- Tinted safety glass
- Control pedals for boom telescoping , elevating and
engine throttle.
- Front windshield wiper and washer
- Roof window wiper and washer
- Power window (Door of the cab)
- 3 way adjustable cloth seat with armrests, high back and
headrest.
- Self centering finger control levers with pilot control.
- Cab floor mat
- Cigarette lighter
- 4 metric ton hook with swivel.
- Weighted hook storage compartment
- Oil cooler
- Four hydraulic, three-section beam and jack outriggers.
2.2 m~7.2 m (7.22'~23.62')
- Front stabilizer (Fifth jack)
- Boom rest

HOISTING PERFORMANCE
LINE SPEEDS AND PULLS DRUM WIRE ROPE CAPACITIES
Main hoist - 0.32m (12-5/8") drum Main drum grooved lagging
2 Line pulls Wire rope 16mm (5/8") wire rope
Layer Line speeds
Available1 Permissible
3 layer Rope per layer Total wire rope
m/min F.P.M kgf Lbs. kgf Lbs. Meters Feet Meters Feet
1st 98 321 6,430 14,200 5,710 12,600 1 30.1 98.8 30.1 98.8
2nd 107 351 5,890 13,000 5,210 11,500 2 32.8 107.6 62.9 206.4
3rd 115 377 5,430 12,000 4,760 10,500 3 35.3 115.8 98.2 322.2
4th 124 406 5,040 11,100 4,400 9,700 4 37.8 124.0 136.0 446.2
5th 132 433 4,700 10,400 4,080 9,000 5 40.5 132.9 176.5 579.1
6th 140 459 4,400 9,700 3,800 8,400 6 43 141.1 219.5 720.1

1
Developed by machinery with each layer of wire rope, but not based DRUM DIMENSIONS
on rope strength or other limitation in machinery or equipment. mm Inch
2
Line speeds based only on hook block, not loaded. Root diameter 320 12-5/8"
3
Permissible line pull may be affected by wire rope strength. Length 484 19-1/16”
Flange diameter 530 20-7/8"

-3-
TM-35100 WORKING RANGE CHART

-4-
TM-35100 RATED LIFTING CAPACITIES (IN METRIC TONS)
ON OUTRIGGERS FULLY EXTENDED 7.2m (23' 7 1/2") + FRONT STABILIZER EXTENDED (360°）
ON OUTRIGGERS FULLY EXTENDED 7.2m (23' 7 1/2") (OVER SIDES AND REAR)
A 9.35 13.6 17.8 22.1 26.3 30.5
B C (30.7ft) C (44.7ft) C (58.5ft) C (72.4ft) C (86.2ft) C (100ft)
1.83
1 83 75.6
75 6 31.7
31 7
2.44 71.6 27.7
3.05 67.4 24.3 75.3 14.5
3.66 63.1 21.8 72.6 14.5 77.3 12.2
4.57 56.3 18.4 68.6 14.5 74.4 12.2 78.0 10.0
6.10 42.9 13.6 61.3 13.6 69.3 12.0 74.1 9.8 77.1 7.7 79.5 7.0
7.62 53.3 10.3 63.9 10.4 70.0 8.6 73.9 7.6 76.9 6.6
9.14 44.1 7.6 58.0 7.8 65.7 7.7 70.5 6.8 74.0 5.9
10.67 32.5 5.9 51.6 6.1 61.0 6.2 66.9 6.1 71.1 5.3
12.12 44.8 4.9 56.3 5.0 63.2 5.0 68.2 4.9
13.72 36.2 4.0 50.8 4.1 59.0 4.1 64.8 4.2
15.24 25.4 3.3 45.1 3.4 54.7 3.5 61.3 3.5
16.76 38.7 2.9 50.3 2.9 57.8 3.0
18.29 30.9 2.4 45.4 2.5 54.1 2.5
19.81 40.1 2.1 50.1 2.1
21.34 34.0 1.8 46.0 1.8
22.86 26.6 1.6 41.5 1.6
24.38 36.5 1.4
25.91 30.6 1.1
27.43 23.3 0.9
28.96 10.7 0.7
D 0

ON OUTRIGGERS FULLY EXTENDED 7.2m (23' 7 1/2") + FRONT STABILIZER EXTENDED (360°）
ON OUTRIGGERS FULLY EXTENDED 7.2m" (23' 7 1/2) (OVER SIDES AND REAR)
A 9.35 13.6 17.8 22.1 26.3 30.5
C B (30.7ft) B (44.7ft) B (58.5ft) B (72.4ft) B (86.2ft) B (100ft)
0 7.99 6.8 12.23 4.5 16.46 2.3 20.70 1.4 24.90 0.9 29.13 0.7
A:Boom length in meters B:Load radius in meters
C:Loaded boom angle (o) D:Minimum boom angle (o) for indicated length (no load)

ON OUTRIGGERS FULLY EXTENDED 7.2m (23' 7 1/2") + FRONT STABILIZER EXTENDED (360°）
ON OUTRIGGERS FULLY EXTENDED 7.2m (23' 7 1/2") (OVER SIDES AND REAR)
Boom 30.5m (100ft) Boom + 8.6m (28.2ft) Jib 30.5m (100ft) Boom + 15.2m (50ft) Jib
Angle o o o
in 5 Tilt 25 Tilt 45 Tilt 5o Tilt 25o Tilt 45o Tilt
Degree R W R W R W R W R W R W
79.5 8.8 3.1 11.5 1.7 13.4 1.2 11.0 1.3 15.8 0.8 19.1 0.5
76 11.4 2.7 14.0 1.6 15.8 1.2 14.3 1.3 18.8 0.8 21.8 0.5
72 14.3 2.3 16.8 1.5 18.4 1.1 17.8 1.2 22.0 0.7 24.6 0.5
70 15.6 2.1 18.1 1.5 19.6 1.1 19.5 1.1 23.5 0.7 26.0 0.5
65 18.9 1.8 21.3 1.3 22.6 1.1 23.5 1.0 27.2 0.6 29.2 0.5
60 22.0 1.6 24.2 1.2 25.4 1.0 27.2 0.9 30.6 0.6 32.2 0.5
55 24.8 1.4 26.9 1.2 27.9 1.0 30.6 0.7 33.8 0.5 34.8 0.5
50 27.3 1.1 29.3 1.0 30.0 0.9 33.7 0.7 36.4 0.5 36.9 0.3
45 29.6 0.9 31.4 0.8 31.7 0.7 36.1 0.5 38.5 0.3 38.7 0.2
40 31.5 0.6 33.1 0.6 38.4 0.3 40.5 0.2
35 33.3 0.5 34.7 0.4
R:Load radius in meters W:Rated lifting capacity in metric tons

-5-
TM-35100 RATED LIFTING CAPACITIES (IN METRIC TONS)
ON OUTRIGGERS MID2 EXTENDED 5.54m (18' 2 1/8") + FRONT STABILIZER EXTENDED (360°）
ON OUTRIGGERS MID2 EXTENDED 5.54m (18' 2 1/8") (OVER SIDES AND REAR)
A 9.35 13.6 17.8 22.1 26.3 30.5
B C (30.7ft) C (44.7ft) C (58.5ft) C (72.4ft) C (86.2ft) C (100ft)
1.83 75.6 31.7
2.44 71.6 27.7
3.05 67.4 24.3 75.3 14.5
3.66 63.1 21.8 72.6 14.5 77.3 12.2
4.57 56.3 18.4 68.6 14.5 74.4 12.2 78.0 10.0
6.10 42.8 11.4 61.2 11.9 69.3 12.0 74.1 9.8 77.1 7.7 79.5 7.0
7.62 53.1 7.6 63.6 7.7 69.9 7.9 73.9 7.6 76.9 6.6
9.14 43.8 5.3 57.6 5.5 65.3 5.6 70.2 5.6 73.9 5.7
10.67 32.3 3.9 51.2 4.0 60.5 4.1 66.3 4.2 70.6 4.3
12.12 44.5 3.1 55.8 3.2 62.6 3.3 67.5 3.3
13.72 35.8 2.4 50.3 2.5 58.3 2.5 64.0 2.6
15.24 25.0 1.9 44.6 2.0 54.1 2.0 60.5 2.1
16.76 38.1 1.6 49.6 1.6 57.0 1.7
18.29 30.4 1.3 44.8 1.3 53.3 1.3
19.81 39.5 1.0 49.4 1.1
21.34 33.4 0.8 45.2 0.9
22.86 26.0 0.6 40.7 0.7
24.38 35.7 0.5
25.91 29.8 0.4
D 0 28

ON OUTRIGGERS MID2 EXTENDED 5.54m (18' 2 1/8") + FRONT STABILIZER EXTENDED (360°）
ON OUTRIGGERS MID2 EXTENDED 5.54m (18' 2 1/8") (OVER SIDES AND REAR)
A 9.35 13.6 17.8 22.1 26.3
C B (30.7ft) B (44.7ft) B (58.5ft) B (72.4ft) B (86.2ft)
0 7.99 6.4 12.23 2.9 16.46 1.6 20.70 0.8 24.90 0.4
A:Boom length in meters B:Load radius in meters
C:Loaded boom angle (o) D:Minimum boom angle (o) for indicated length (no load)

ON OUTRIGGERS MID2 EXTENDED 5.54m (18' 2 1/8") + FRONT STABILIZER EXTENDED (360°）
ON OUTRIGGERS MID2 EXTENDED 5.54m (18' 2 1/8") (OVER SIDES AND REAR)
Boom 30.5m (100ft)
( ) Boom + 8.6m (28.2ft)
( ) Jib 30.5m (100ft)
( ) Boom + 15.2m (50ft)
( ) Jib
A l
Angle o o o
in 5 Tilt 25 Tilt 45 Tilt 5o Tilt 25o Tilt 45o Tilt
Degree R W R W R W R W R W R W
79.5 8.8 3.1 11.5 1.7 13.4 1.2 11.0 1.3 15.8 0.8 19.1 0.5
76 11.4 2.7 14.0 1.6 15.8 1.2 14.3 1.3 18.8 0.8 21.8 0.5
72 14.3 2.3 16.8 1.5 18.4 1.1 17.8 1.2 22.0 0.7 24.6 0.5
70 15.6 2.1 18.1 1.5 19.6 1.1 19.5 1.1 23.5 0.7 26.0 0.5
65 18.6
18 6 1.4
14 21.1
21 1 1.2
12 22.6
22 6 1.1
11 23.5
23 5 1.0
10 27.2
27 2 0.6
06 29.2
29 2 0.5
05
60 21.3 0.9 23.6 0.7 24.9 0.7 26.8 0.6 30.4 0.5 32.0 0.4
55 23.9 0.5 26.0 0.4 27.0 0.4 29.7 0.3 33.0 0.2 34.2 0.2
50 26.4 0.2

R:Load radius in meters W:Rated lifting capacity in metric tons

-6-
TM-35100 RATED LIFTING CAPACITIES (IN METRIC TONS)

ON OUTRIGGERS MID1 EXTENDED 3.88m (12' 8 3/4") + FRONT STABILIZER EXTENDED (360°）
ON OUTRIGGERS MID1 EXTENDED 3.88m (12' 8 3/4") (OVER SIDES AND REAR)
A 9.35 13.6 17.8 22.1 26.3 30.5
B C (30.7ft) C (44.7ft) C (58.5ft) C (72.4ft) C (86.2ft) C (100ft)
1.83 75.6 31.7
2.44 71.6 27.7
3.05 67.4 24.3 75.4 14.5
3.66 63.1 16.6 72.7 14.5 77.5 12.2
4.57 56.2 10.1 68.5 10.6 74.4 10.8 78.0 10.0
6.10 42.7 5.6 60.9 6.0 68.9 6.2 73.6 6.3 77.1 6.3 79.5 6.4
7.62 52.9 3.9 63.3 4.0 69.2 4.1 73.3 4.2 76.3 4.3
9.14 43.7 2.7 57.4 2.8 64.7 2.9 69.6 2.9 73.1 3.0
10.67 32.1 1.9 51.0 2.0 60.0 2.1 65.8 2.1 69.9 2.2
12.12 44.3 1.5 55.3 1.5 62.2 1.6 66.8 1.6
13.72 35.6 1.0 49.9 1.1 57.9 1.1 63.3 1.2
15.24 24.8 0.7 44.2 0.8 53.7 0.8 59.9 0.9
16 76
16.76 37 7
37.7 05
0.5 49 3
49.3 05
0.5 56 4
56.4 06
0.6
18.29 30.0 0.3 44.4 0.3 52.7 0.4
D 0 29 44 52

ON OUTRIGGERS MID1 EXTENDED 3.88m (12' 8 3/4") + FRONT STABILIZER EXTENDED (360°）
ON OUTRIGGERS MID1 EXTENDED 3.88m (12' 8 3/4") (OVER SIDES AND REAR)
A 9.35 13.6 17.8
C B (30.7ft) B (44.7ft) B (58.5ft)
0 7.99 3.1 12.23 1.3 16.46 0.5

A:Boom length in meters B:Load radius in meters

C:Loaded boom angle (o) D:Minimum boom angle (o) for indicated length (no load)

ON OUTRIGGERS MID1 EXTENDED 3.88m (12' 8 3/4") + FRONT STABILIZER EXTENDED (360°）
ON OUTRIGGERS MID1 EXTENDED 3.88m (12' 8 3/4") (OVER SIDES AND REAR)
Boom 30.5m (100ft) Boom + 8.6m (28.2ft) Jib 30.5m (100ft) Boom + 15.2m (50ft) Jib
Angle o o o
in 5 Tilt 25 Tilt 45 Tilt 5o Tilt 25o Tilt 45o Tilt
Degree R W R W R W R W R W R W
79.5 8.8 3.1 11.5 1.7 13.4 1.2 11.0 1.3 15.8 0.8 19.1 0.5
76 11.2 2.2 14.0 1.6 15.7 1.2 14.3 1.3 18.8 0.8 21.8 0.5
72 13 6
13.6 12
1.2 16 2
16.2 10
1.0 18 0
18.0 08
0.8 17 4
17.4 09
0.9 21 8
21.8 06
0.6 24 6
24.6 05
0.5
70 14.8 0.9 17.4 0.7 19.0 0.6 18.8 0.6 23.0 0.4 25.9 0.3
65 17.7 0.3 20.1 0.2 21.5 0.2 22.2 0.2
R:Load radius in meters W:Rated lifting capacity in metric tons

-7-
TM-35100 RATED LIFTING CAPACITIES (IN METRIC TONS)

ON OUTRIGGERS MIN EXTENDED 2.21m (7' 2 7/8") (360°）

A 9.35 13.6
B C (30.7ft) C (44.7ft)
1.83 75.6 18.2
2.44 71.5 12.7
3.05 67.3 8.0 75.5 8.5
3.66 63.0 5.6 72.6 6.0
4.57 56.1 3.5 68.3 3.9
6.10 42.7 1.8 60.9 2.1
7.62 52.8 1.1
9.14 43.6 0.6
D 0 32

ON OUTRIGGERS MIN EXTENDED 2.21m (7' 2 7/8") (360°）

A 9.35
C B (30.7ft)
0 7.99 0.8
A:Boom length in meters B:Load radius in meters
C:Loaded boom angle (o) D:Minimum boom angle (o) for indicated length (no load)

NOTE: The lifting capacity data stowed in the LOAD MOMENT INDICATOR(AML-L) is based on
the standard number of parts of line listed in the chart.

Boom length in meters 9.35 9.35 to 22.1 22.1 to 30.5

JIB
(feet) (30.7) (30.7 to 72.4) (72.4 to 100.0)
Number of parts of lines 8 4 2 1
Max. of load in kirograms 31,700 16,000 8,000 3,100

-8-
WARNING AND OPERATING INSTRUCTIONS
FOR LIFTING CAPACITIES
GENERAL 8. Do not operate at boom lengths, radii, or boom angle, where
1. RATED LIFTING CAPACITIES apply only to the machine as no capacities are shown. Crane may overturn without any
originally manufactured and normally equipped by TADANO load on the hook.
LTD. 9. When boom length is between values listed, refer to the
Modifications to the machine or use of optional equipment rated lifting capacities of the next longer and next shorter
other than that specified can result in a reduction of capacity. booms for the same radius. The lesser of the two rated lifting
2. Construction equipment can be hazardous if improperly capacities shall be used.
operated or maintained. Operation and maintenance of this 10. When making lifts at a load radius not shown, use the next
machine must be in compliance with information in the longer radius to determine allowable capacity.
operation, safety and maintenance manual supplied with 11. Load per line should not exceed 4,000kg (8,820 lbs.) for
machine. If these manuals are missing, order replacements main winch.
through the distributor. 12. Check the actual number of parts of line with LOAD MOMENT
3. The operator and other personnel associated with this INDICATOR (AML-L) before operation. Maximum lifting
machine shall fully acquaint themselves with the latest capacity is restricted by the number of parts of line of LOAD
American National Standards Institute (ANSI) safety MOMENT INDICATOR (AML-L). Limited capacity is as
standards for cranes. determined from the formula, Single line pull for main winch
(4,000 kg) x number of parts of line.
SET UP 13. The boom angle before loading should be greater to account
1. Rated lifting capacities on the chart are the maximum for deflection. For rated lifting capacities, the loaded boom
allowable crane capacities and are based on the machine angle and the load radius is for reference only.
standing level on firm supporting surface under ideal job 14. The 9.35m (30.7') boom length capacities are based on boom
conditions. Depending on the nature of the supporting fully retracted. If not fully retracted [less than 13.6m (44.7')
surface, it may be necessary to have structural supports boom length], use the rated lifting capacities for the 13.6m
under the outrigger floats to spread the loads to a larger (44.7') boom length.
bearing surface. 15. Extension or retraction of the boom with loads may be
2. For outrigger operation, outriggers shall be properly extended attempted within the limits of the RATED LIFTING CAPACITIES.
with tires free of supporting surface before operating crane. The ability to telescope loads is limited by hydraulic pressure,
The front jack must be properly extended. boom angle, boom length, crane maintenance, etc.
16. When jib removing, jib state switch select removed,
OPERATION 17. When erecting and stowing jib, be sure to retain it by hand or by
1. Rated lifting capacities have been tested to and meet other means to prevent its free movement.
minimum requirements of SAE J1063-Cantilevered Boom 18. Use "ANTI-TWO-BLOCK DEVICE" disable switch when erecting
Crane Structures Method of Test. and stowing jib and when stowing hook block. While the switch
2. Rated lifting capacities do not exceed 85% of the tipping is pushed, the hoist does not stop, even when overwind
load on outriggers fully extended as determined by SAE condition occurs.
J765-Crane Stability Test Code. 19. For boom length with 8.6m (28.2') jib, rated lifting capacities
Rated lifting capacities for partially extended outriggers are are determined by loaded boom angle only in the column
determined from the formula, Rated Lifting Capacities headed "30.5m (100') boom + 8.6m (28.2') jib".
=(Tipping Load - 0.1 x Tip Reaction)/1.25. For boom length with 15.2m (50.0') jib, rated lifting capacities are
3. Rated lifting capacities above bold lines in the chart are determined by loaded boom angle only in the column headed
based on crane strength and those below, on its stability. "30.5m (100') boom + 15.2m (50.0') jib".
They are based on actual load radius increased by boom For amgles not shown, use the next lower loaded boom angle to
deflection. determine allowable capacity.
4. The weight of handling device such as hook blocks, slings,
etc., must be considered as part of the load and must be
deducted from the lifting capacities.
5. Rated lifting capacities are based on freely suspended loads
and make no allowance for such factors as the effect of wind,
sudden stopping of loads, supporting surface conditions, DEFINITIONS
operating speeds, side loads, etc. Side pull on boom or jib 1. Load Radius: Horizontal distance from a projection of the axis
is extremely dangerous. of rotation to supporting surface before loading to the center of
6. Rated lifting capacities do not account for wind on lifted load the vertical hoist line or tackle with load applied.
or boom. We recommend against working under the condition 2. Loaded Boom Angle: The angle between the boom base
that the load is out of control due to a strong wind. During section and the horizontal, after lifting the rated lifting capacity
boom lift, consider that the rated lifting capacity is reduced at the load radius.
by 50% when the wind speed is 9m/s (20mph) to 12m/s 3. Working Area: Area measured in a circular arc about the
(27mph) ; reduced by 70% when the wind speed is 12m/s centerline of rotation.
(27mph) to 14m/s (31mph). If the wind speed is 14m/s 4. Freely Suspended Load: Load hanging free with no direct
(31mph) or over, stop operation. During jib lift, stop operation external force applied except by the hoist line.
if the wind speed is 9m/s (20mph). 5. Side Load: Horizontal side force applied to the lifted load either
7. Rated lifting capacities at load radius shall not be exceeded. on the ground or in the air.
Do not tip the crane to determine allowable loads.

-9-
WARNING AND OPERATING INSTRUCTIONS
FOR USING THE LOAD MOMENT INDICATOR (AML-L)
1. When operating crane on outriggers: 4. The displayed values of LOAD MOMENT INDICATOR
 Set Starter switch to "ON" . (AML-L) are based on freely suspended loads and make no
 Press the outrigger mode select key to register for the allowance for such factors as the effect of wind, sudden
outrigger operation. Press the set key, then the outrigger stopping of loads, supporting surface conditions, operating
mode indicative symbol
y changes
g from flickering
g to speed,
p side loads, etc.
lighting. For safe operation, it is recommended when extending
 Press the boom mode select key to register the boom and lowering boom or slewing, lifting loads shall be
mode, then the boom mode indicative symbol changes appropriately reduced.
from lighting to flickering. Each time the boom mode 5. LOAD MOMENT INDICATOR (AML-L) is intended as an aid
select key is pressed, the mode changes. Press the set to the operator. Under no condition should it be relied upon
key to select the status that corresponds to the actual to replace use of capacity charts and operating instruction.
state of the boom, then the boom mode indicative symbol Sole reliance upon LOAD MOMENT INDICATOR (AML-L)
changes from flickering to lighting. aids in place of good operating practice can cause an
 When erecting and stowing jib, select the status of jib accident. The operator must exercise caution to assure
set (j
(jib state indicative symbol
y flickers).
) safety.
y
2. This machine is equipped with an automatic slew stopping 6. The lifting capacity for over-side area differs depending on
device.(For the details, see Operation Maintenance Manual.) the outrigger extension width. Work with the capacity
But operate very carefully because the automatic slew stop corresponding to the extension width. The lifting capacities
does not work in the following cases. for over-front and over-rear areas are for "outriggers fully
 When the "AML OVERRIDE "switch is set to "ON "and the extended" or "outriggers mid2 extended". For the areas
"OVERRIDE "key switch outside the cab is on. (angle a and b),see the following table. When using on
3. During crane operation, make sure that the displays on front "front jack not extended" or "other outrigger extension status",
panel are in accordance with actual operating conditions. see Operation Manual.

On outriggers
Lifting capacity On outriggers fully extended
Mid2 extended
Extended Width 5.54 m (18' 2-1/8") 3.88 m (12' 8-3/4") 2.21 m (7' 2-7/8")
Angle ao 40 20 10
o
Angle b 35 20 15
 Angle a and b show minimum value.  FRONT JACK EXTENDED

CARRIER REQUIREMENTS
Wheelbase(WB) - Minimum 6,600 mm (260 in)

Cab to Axle/trunnion (CA/CT) - Minimum 4,820 mm (190 in)

After frame (AF) -Minimum

Minimum 1
1,473
473 mm (58 in)

3 3
Frame Section Modulus (SM) - Minimum 492 cm (30 in ) per rail (110,000 PSI steel)

PTO torque - 470 N-m (350 ft-lbs)

PTO revolution - Maximum 2,150 rpm

Permissible axle load

Kilograms Pounds
GVW Front Rear GVW Front Rear
Permissible axle load 24,400 9,000 15,400 54,000 20,000 34,000

TM-35100 on MINIMUM CARRIER(STERLING LT7501), Axle weight distribution chart

Kilograms Pounds
GVW Front Rear GVW Front Rear
Base machine with 256L (70gal.) fuel. 24,113 8,895 15,218 53,160 19,610 33,550

Remove 4 metric ton hook ball. -100 -113 13 -220 -250 30

Option: 1. Hot water cab heater and air conditioning in upper cab 100 14 86 220 30 190
2. Radio control 77 -19 96 170 -42 212

- 10 -
MEMO

TADANO LTD. (INTERNATIONAL DIVISION) TADANO AMERICA CORPORATION

4-12, Kamezawa 2-chome, Sumida-ku, 4242 West Greens Rd.
Tokyo 130-0014, JAPAN Houston, Taxas, 77066 U.S.A.
PHONE: 81-3-3621-7750 PHONE: (281) 869-0030
FAX: 81-3-3621-7785 FAX: (281) 869-0040
http://www.tadano.co.jp/indexe.html http://www.tadanoamerica.com

Form No. TM-3500-1-90202/ES-01

- 11 -