Megrbt 19

GODAVARI INSTITUTE OF ENGINEERING & TECHNOLOGY
((AUTONOMOUS)
Approved by AICTE, Accredited by NBA & NAAC ‘A+’ Grade, Recognized under 2(f) and 12(b) of UGC, Permanently Affiliated to JNTUK, Kakinada
DEPARTMENT OF MECHANICAL ENGINEERING
4 Years B.Tech. (Mechanical Engineering) Course Structure: (2019-20)
GRBT-19
COURSE STRUCTURE AND SYLLABUS
Godavari institute of Engg& Technology

Approved By AICTE NAAC’A+’ Grade Recognized by UCG,U/Sec.2(f)&12(B) Permanent affiliation by
JNTUK, GIET Campus, Chaitanya Knowledge city,NH-16,Rajahmundry,East Godavari, A.P.
Tel:+91-883-2484828-31www.giet.ac.in
____________________________________________________________________________________
Chaitanya Knowledge City, NH-16, Rajanagaram, Rajahmundry – 533294. E.G.Dt. – A.P.- INDIA
((AUTONOMOUS)
COURSE STRUCTURE
SYLLABUS
BOS MINUTES
REGULATIONS
MECHANICAL ENGINEERING

(AUTONOMOUS)
Approved By AICTE, NAAC - A+ Grade Recognized by UCG,U/Sec.2(f)&12(B) Permanent affiliation by
JNTUK
GIET Campus, Chaitanya Knowledge city,NH-16,Rajahmundry,East Godavari, A.P.

Tel:+91-883-2484828 31www.giet.ac.in
GRBT- 19 COURSE STRUCTURE

Mechanical Engineering
____________________________________________________________________________________
((AUTONOMOUS)
B. Tech. I Semester
S. Course Course Periods per Week

Subject Title Credits Internal External Total
NO Code Type
L T P
1 19198101 BSC Mathematics-I 3 0 0 3 30 70 100
2 19198102 HSMC Communicative English I 3 0 0 3 30 70 100
3 19198103 BSC Engineering Chemistry 3 0 0 3 30 70 100
Basic Electrical &

4 19199104 ESC 3 0 0 3 30 70 100
Electronics Engineering
Professional Ethics &
5 19198105 MC 2 0 0 0 30* _ _
Human Values
6 19198176 ESC Engineering Graphics 1 0 3 2.5 30 70 100
Communicative English
7 19198111 HSMC 0 0 3 1.5 50 50 100
Laboratory
Engineering Chemistry
8 19198112 BSC 0 0 3 1.5 50 50 100
Laboratory
Basic Electrical &
9
19199113 ESC Electronics Engineering 0 0 3 1.5 50 50 100
Lab
Total 15 0 12 19 300 500 800
BSC = 7.5 ESC=7 HSMC=4.5 MC=0
B. Tech. II Semester
____________________________________________________________________________________
((AUTONOMOUS)
S. Course Periods per Week

NO Code
L T P
1 19198201 BSC Mathematics-II 3 0 0 3 30 70 100
Communicative
2 19198202 HSMC 3 0 0 3 30 70 100
English II
Engineering Physics
3 19198203 BSC 3 0 0 3 30 70 100
and its Applications
Problem Solving &
4 19199204 ESC 2 1 0 3 30 70 100
Programming in C
5 19198205 MC Environmental Studies 2 0 0 0 30* _ _
Engineering
6 19198206 ESC 2 1 0 3 30 70 100
Mechanics
Communicative
7 19198211 HSMC 0 0 3 1.5 50 50 100
English Laboratory -II
Engineering Physics
8 19198212 BSC 0 0 3 1.5 50 50 100
Laboratory
Problem Solving &
9 19199213 ESC Programming 0 0 3 1.5 50 50 100
Laboratory using C
Basic Engineering
10 19198214 ESC 0 0 3 1.5 50 50 100
Workshop
Total 15 2 12 21 350 550 900
BCS=7.5 ESC=9 HSMC=4.5 MC=0
____________________________________________________________________________________
((AUTONOMOUS)
B. Tech. III Semester

NO Code L T P
1 19139301 BSC Mathematics-III 3 0 0 3 30 70 100
Metallurgy &Materials
2 19130302 ESC 3 0 0 3 30 70 100
Science
3 19130303 PCC Mechanics of Solids 2 1 0 3 30 70 100
4 19130304 PCC Kinematics of Machinery 2 1 0 3 30 70 100
5 19130305 PCC Thermodynamics 2 1 0 3 30 70 100
Fluid Mechanics &

6 19130306 PCC 3 0 0 3 30 70 100
Hydraulic Machinery
Design Thinking &
7 19130387 MC 2 0 0 0 30* _ _
Product Innovation
Mechanics of Solids &
8 19130311 PCC 0 0 3 1.5 50 50 100
Metallurgy lab
Fluid Mechanics &
9 19130312 PCC 0 0 3 1.5 50 50 100
Hydraulic Machinery Lab
Total 17 3 6 21 280 520 800
BCS = 3 ESC =3 PCC = 15
____________________________________________________________________________________
((AUTONOMOUS)
B. Tech. IV Semester

No Code L T P
Numerical Methods and
1 19139401 BSC 3 0 0 3 30 70 100
Probability & Statistics
2 19130402 PCC Dynamics of Machinery 3 0 0 3 30 70 100
3 19130403 PCC Thermal Engineering -I 3 0 0 3 30 70 100
4 19130404 PCC Production Technology 3 0 0 3 30 70 100
Open Elective-1
Environmental Pollution &
19131465a
Control
Utilization of Electrical
19132465a
Energy
5 19134465a OEC Internet of Things 3 0 0 3 30 70 100
19135465a Operating Systems
Elements of Mining
19136465a
Technology
Basic Automobile
19137465a
Engineering
Computer Aided Machine
6 19130411 PCC 1 0 3 2.5 50 50 100
Drawing Practice
7 19130412 PCC Thermal Engineering Lab. 0 0 3 1.5 50 50 100
8 19130413 PCC Production Technology Lab 0 0 3 1.5 50 50 100
Community Service
9 19130421 PR 0 0 1 0.5 100 _ 100
Oriented Project
Total 16 0 10 21 380 520 900
ESC OEC = PR =
BCS = 3 PCC = 14.5
=0 3 0.5
____________________________________________________________________________________
((AUTONOMOUS)
B. Tech. V Semester

No Code L T P
1 19130501 PCC Design of Machine Members 2 1 0 3 30 70 100
2 19130502 PCC Thermal Engineering -II 2 1 0 3 30 70 100
Metal Cutting & Machine
3 19130503 PCC 3 0 0 3 30 70 100
Tools
Department Elective-1
A. Fuels Combustion and
19130564A
4 PEC Emission control 3 0 0 3 30 70 100
19130564B B. Tribology
19130564C C. Industrial Robotics
19130564D D. Advanced Materials
Open Elective-2
19131565a Solid Waste Management
19132565a Energy management
19134565a Digital Image Processing
5 OEC 3 0 0 3 30 70 100
19135565a Information Security
Disaster Management in
19136565a
Mining
19137565a Hybrid and Electric Vehicles
6 19193511 PCC Theory of Machines Lab. 0 0 3 1.5 50 50 100
7 19193512 PCC Machine Tools Lab. 0 0 3 1.5 50 50 100
8 19139513 HSMC Soft Skills 0 0 3 1.5 50 50 100
Mini Project-1/Study
9 19130521 PR 0 0 0 1.5 100 _ 100
Project/Internship
Total 14 1 9 21 400 500 900
HSMC
PEC = 3 PCC = 12 OEC = 3 PR=1.5
= 1.5
____________________________________________________________________________________
((AUTONOMOUS)
B. Tech. VI Semester

No Code L T P
1 19130601 PCC Design of Transmission Elements 2 1 0 3 30 70 100
2 19130602 PCC Industrial Engineering & Management 3 0 0 3 30 70 100
3 19130603 PCC Heat Transfer 2 1 0 3 30 70 100
4 19130604 PCC Metrology and Instrumentation 3 0 0 3 30 70 100
A. Refrigeration and Air
19130665A
Conditioning
5 19130665B PEC B. Mechatronics 3 0 0 3 30 70 100
C. Advanced Foundry and Welding
19130665C
Technology
19130665D D. Non Destructive Evaluation
Open Elective 3
a. Global Environment
19131666a
Problems & Policies
b. Renewable Energy
19132666a
Resources
19134666a c. Data Communication
6 3 0 0 3 30 70 100
OEC d. Human Computer
19135666a
Interaction
e. Remote sensing & GIS in
19136666a
Mining
f. Modern Vehicle
19137666a
Technology
7 19139687 MC Constitution of India 2 0 0 0 30* - -
8 19130611 PCC Heat Transfer Lab 0 0 3 1.5 50 50 100
9 19130612 PCC Metrology and Instrumentation Lab 0 0 3 1.5 50 50 100
Total 18 2 6 21 280 520 800
HSMC OEC
PEC = 3 PCC = 15 PR=0
=0 =3
____________________________________________________________________________________
((AUTONOMOUS)
B. Tech. VII Semester

No Code L T P
1 19130701 PCC Finite Element Methods 3 0 0 3 30 70 100
2 19130702 PCC CAD/CAM 3 0 0 3 30 70 100
19130763A A. Power Plant Engineering
19130763B B. Mechanical Vibrations
3 PEC 3 0 0 3 30 70 100
19130763C C. Automobile Engineering
D. Advanced Machining
19130763D
Processes
A. Gas Dynamics & Jet
19130764A
Propulsions
B. Micro Electro
19130764B
4 PEC Mechanical System 3 0 0 3 30 70 100
C. Design for
19130764C
Manufacturing
D. Automation in
19130764D
Manufacturing
Open Elective-4
a. Managerial Economics
19139765a
and Financial Analysis
b. Entrepreneurship
19139765b
Qualities for Engineers
19139765c c. Principles of Management
d. Financial Management
19139765d
for Engineers
5 OEC 3 0 0 3 30 70 100
19139765e e. Operations management
19139765f f. Digital Marketing
g. Total Quality
19139765g
Management
h. Organizational
19139765h
Behaviour
i. Human Resource
19139765i
Management
Intellectual Property Rights
6 19139786 MC 2 0 0 0 30* _ _
and Patents
7 19130711 PCC CAD/CAM Lab 0 0 3 1.5 100 100
8 19130721 PR Mini Project - 2/Internship 0 0 0 2 100 100
9 19130731 PR Fabrication Project 0 0 5 2.5 50 50 100
Total 17 0 8 21 430 400 800
PEC = 6 MC = 0 PCC = 7.5 OEC = 3 PR=4.5
____________________________________________________________________________________
((AUTONOMOUS)
B. Tech. VIII Semester
S. Periods per Week

Course Code Subject Title Credits Internal External Total
No L T P
1 19139801 HSMC Operations Research 3 0 0 3 30 70 100
A. Computational Fluid
19130862A
Dynamics
2 19130862B PEC B. Nano Technology 3 0 0 3 30 70 100
19130862C C. Additive Manufacturing
D. Production Planning
19130862D
and Control
3 19130841 PR Project 0 0 18 9 80 120 200
Total 6 0 18 15 140 260 400
PEC =3 PR = 9 HSMC = 3
NOTE:- L - LECTURE T- THEORY P – PRACTICAL C – CREDITS
____________________________________________________________________________________
((AUTONOMOUS)
COURSE COMPONENT DISTRIBUTION
Sl. Categ GRBT APSCH AICTE

Category Category Description
No. ory -19 E credits
BS
1 Basic Sciences Basic Science courses 21 24 25
Mandatory Courses[Environmental
Mandatory Sciences, Induction training, Indian
2 MC 0 0 0
Courses Constitution,Essence of Indian Traditional
Knowledge](non-credit)
Engineering Science courses including
Engineering
3 workshop, drawing, basics of electrical/ ES 19 24 24
Sciences
mechanical/ computer etc
Professional
4 Professional core courses PC 64 51.5 48
Core
Professional Professional Elective courses relevant to
5 PE 15 15 18
Electives chosen specialization/branch
Open subjects – Electives from other
6 Open Electives OE 12 15 18
technical and /or emerging subjects
Humanities &
Humanities and Social Sciences
7 Social HS 13.5 13 12
including Management courses
Sciences
Project work, seminar and internship in
8 Projects PR 15.5 13 15
industry or elsewhere
9 Lab Courses Practical Lab based Courses LC 0 4.5
Tot
160 160 160
al ==>
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
Course Code
Dynamics of Machinery
Teaching Totalcontacthours-55 L T P C
Prerequisite(s): Kinematics of Machinery 3 0 0 3
Course Objective:
The students completing this course are expected to equip the student with fundamental knowledge of
dynamics of machines so thatstudent can appreciate problems of dynamic force balance, transmissibility of
forces, isolation ofsystems, vibrations.Develop knowledge of analytical and graphical methods for
calculating balancing of rotaryand reciprocating masses.Develop understanding of vibrations and its
significance on engineering design.Develop understanding of dynamic balancing, flywheel analysis,
gyroscopic forces andmoments.
Course Outcomes:
On Completion of the course, the students will be able to-

CO1: Analyze stabilization of sea vehicles, aircrafts and automobile vehicle. (Analyze)
CO2: Compute frictional losses, torque transmission of mechanical systems (Compute)
CO3: Analyze and design the flywheels and governors (Analyze).
CO4: Estimate the unbalanced forces in reciprocating and rotary masses (Estimate).
CO5: Understand free and forced vibrations of single degree freedom systems (Understand).
Syllabus:
UNIT–I
PRECESSION: Gyroscopes, effect of precession motion on the stability of moving vehicles such as
motor car, motorcycle, aeroplanes and ships.
UNIT–II
FRICTION: Inclined p l a n e , f r i c t i o n o f s c r e w a n d n u t s , p i v o t a n d c o l l a r , uniform
pressure, uniform wear, friction circle and friction axis, lubricated surfaces, boundary friction, film,
lubrication.
CLUTCHES: Friction clutches- single disc or plate clutch, multiple disc clutch, cone clutch,
centrifugal clutch.
BRAKES AND DYNAMOMETERS: Simple block brakes, internal expanding brake, band brake of
vehicle.General description and operation of dynamometers: Prony, Rope brake, Epicyclic, Bevis Gibson
and belt transmission,
UNIT–III
TURNING MOMENT DIAGRAMS: Dynamic f orce analysis of slider crank mechanism, inertia
torque, angular velocity and acceleration of connecting rod, crank effort and turning moment
diagrams–fluctuation of energy–flywheels and their design.
GOVERNERS: Watt, Porter and Proellgovernors, Springloadedgovernors–
HartnellandHartungwithauxiliary springs. sensitiveness, isochronism and hunting.
____________________________________________________________________________________
((AUTONOMOUS)
UNIT– IV
BALANCING: Balancing of rotating massessingleandmultiple–single and differentplanes,use of
analyticalandgraphicalmethods. Primary, secondary,
andhigherbalancingofreciprocatingmasses.Analyticalandgraphical methods, unbalancedforcesandcouples –
examinationof“V” multicylinderinlineandradialenginesforprimary and
secondarybalancing,locomotivebalancing, hammerblow,swayingcouple,variationoftractiveeffort.
UNIT–V
VIBRATIONS: Free vibration of spring mass system – oscillation of pendulums, centres of oscillation
and suspension, transverse loads, vibrations of beams with concentrated and distributed
loads.Dunkerly‟smethods,Raleigh‟smethod,whirlingofshafts,criticalspeeds,torsionalvibrations, two and
three rotor systems. Introduction to damped and forced vibrations.
Text Books:
1. TheoryofMachines,”S.SRatan,Mc.GrawHillPubl.
2. Theory of Machines, ”Thomas Bevan,. CBS Publishers
References:
1 Theoryof Machines,-Khurmi, S.Chand publications
Useful Web-links: http://nptel.ac.in/courses.php
CO-PO Mapping:
( 1: Slight [Low]; 2: Moderate[Medium]; 3: Substantial[High], '-' : No Correlation)
PO1 PO2 PO3 PO4 PO5 PO6 PO7 PO8 PO9 PO10 PO11 PO12
CO1 2 - - - - - - - - - - -
CO2 - - - - - - - - - - - -
CO3 - - - - - 3 - - - - - -
CO4 - - 3 - - - - - - - - -
CO5 - - - - - - 2 - - - - -
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
Regulation Godavari Institute of Engineering & Technology

GRBT-19 (Autonomous) III B.Tech. I Sem
Course Code (5th Semester)
Design of Machine Members
Teaching Total contact hours-64 L T P C

Prerequisite(s): Engineering Mechanics, Mechanics of Solids. 2 1 0 3
(Use of approved design data book is permitted in the end semester examination)
Course Objectives:
 To learn about the basic stresses in machine elements and manufacturing considerations in Machine
design.
 To learn about the strength of various machine elements.
 To learn about the design of riveted and welded and bolted joints of machine components.
 To learn about the design principles in the cotter joints and levers.
 To learn about the design and various application of springs.
Course Outcomes:
On Completion of the course, the students shall be able to-
CO1: Describe the concepts of basic machine elements.
Identify the preferred sizes, codes and selection of proper material for design of
CO2:
machine element
CO3: Design the machine element under static and dynamic loading conditions.
Choose the temporary and permanent joints required to assemble the machine
CO4:
elements.
CO5: Suggest the required spring for the given application.
Syllabus
UNIT-I
INTRODUCTION: General considerations in the design, Engineering Materials and their properties –
Selection –Manufacturing considerations in design, tolerances and fits –BIS codes of steels.
STRESSES IN MACHINE MEMBERS: Simple stresses – Combined stresses – Torsional and bending
stresses – Impact stresses – Stress strain relation – Various theories of failure – Factor of safety – Design for
strength and rigidity – Preferred numbers. The concept of stiffness in tension, bending, torsion and combined
situations.
UNIT-II
STRENGTH OF MACHINE ELEMENTS: Stress concentration – Theoretical stress concentration factor–
Fatigue stress concentration factor– Notch sensitivity – Design for fluctuating stresses – Endurance limit –
Good man‟s line – Soderberg‟s line – modified Good man‟s line.
UNIT- III
RIVETED JOINTS: Types of riveted joints, Design of riveted joints, Boiler shell riveting, eccentric loading.
WELDED JOINTS: Design of transverse and parallel fillet welded joints. Eccentric loading of welded
joints.
UNIT- IV
BOLTED JOINTS: Forms of Screw threads, Stresses in Screw fasteners, Design of bolts with pre-stresses –
Design of joints under eccentric loading
____________________________________________________________________________________
((AUTONOMOUS)
COTTER AND KNUCKLE JOINTS: Cotter joints-Socket and spigot, Sleeve and cotter, Jib and cotter
joints- Knuckle joints.
UNIT- V
MECHANICAL SPRINGS: Stresses and deflections of helical springs – extension -compression springs–
Springs for fatigue loading, energy storage capacity – Helical torsion springs – Co-axial springs,
leaf springs.
LEVERS: Design of levers – Hand levers-Foot lever – Cranked lever – Bell cranked lever of a lever safety
loaded valve- rocker arm.
Text Books:
1.V.B. Bhandari, Machine Design of Machine Elememts, 4/e, Tata McGraw Hill, 2017.
2.Norton, R. L., Machine Design: An Integrated Approach, 5/e, Pearson, 2013.
3.Faculty of Mechanical Engineering, Design Data: Data Book of Engineers, PSG College of Engineering,
2012
References:
1.R.S. Khurmi and J. K. Gupta, Machine design, 25/e, S.Chand Publishers, 2014.
2.T.V. Sundaramoorthy& N.Shanmugam, Machine Design, 6/e, SciTech Publishers, 2010.
3.Shigley, J.E and Mischke, C. R. Mechanical Engineering Design, 8/e, Tata McGraw Hill, 2008.
4.Design data hand book, S. Md. Jalaludeen.
____________________________________________________________________________________
((AUTONOMOUS)

Course Code (5th semester)
Thermal Engineering-II
Prerequisite(s): Fundamentals of Engineering Thermodynamics 2 1 0 3
Course Objectives:
● To investigate thermodynamic analysis of steam power plants and various methods to improve
efficiencies.
● To predict various types of boilers and their performance.
● To name various types nozzles and condensers and to find their efficiencies.
● To examine the performance evaluations of various Turbines.
● To investigate and analyse performances of various systems such as gas turbines, jet and rocket
propulsion.
Course Outcomes:

CO1: Analyze the thermal power plants and different methods to improve plant efficiency.
CO2: Evaluate the performance of various steam nozzles.
CO3: Examine various efficiencies of Condensers and steam turbines.
Discuss gas turbines working principle and different methods to improve thermal efficiencies
CO4:
of gas turbines.
CO5: Choose optimal parameters of jet propulsion units.
Syllabus:
UNIT–I
BASIC CONCEPTS: Carnot cycle - Rankine cycle-schematic layout- Thermodynamic analysis- Concept of
mean temperature of heat addition-Methods to improve cycle performance– Regeneration &reheating.
combustion: fuels and combustion-Concepts of heat of reaction-Adiabatic flame temperature-Stoichiometry-
Fluegas analysis.
UNIT-II
BOILERS: Classification – Working principles of water tube and fire tube boilers with sketches–
Mountings and accessories– Working principles-boiler horse power- equivalent evaporation-Efficiency and
heat balance– Draught- Classification– Height and diameter of chimney for given draught and discharge-
Condition for maximum discharge-Efficiency of chimney– Artificial draught, induced and forced.
UNIT–III
STEAM NOZZLES: Function of a nozzle – Applications- types-Flow through nozzles-Thermodynamic
analysis– Assumptions- Velocity of fluid at nozzle exit- Ideal and actual expansion in a nozzle-Velocity
coefficient-Condition for maximum discharge-Critical pressure ratio-Criteria to decide nozzle shape: Super
saturated flow- Its effects, degree of super saturation and degree of under cooling-Wilson line.
STEAM TURBINES: Classification – Impulse turbine; mechanical details – Velocity diagram – Effect
of friction – Power developed, axial thrust, blade or diagram efficiency – Condition for maximum
____________________________________________________________________________________
((AUTONOMOUS)
efficiency. De-Laval turbine - Methods to reduce rotor speed- Velocity compounding, pressure
compounding and velocity & pressure compounding, velocity and pressure variation along the flow –
Combined velocity diagram for a velocity compounded impulse turbine-Condition for maximum
efficiency.
UNIT-IV
REACTION TURBINE: Mechanical details– Principle of operation, thermodynamic analysis of a stage
and degree of reaction– Velocity diagram– Parson‟s reaction turbine– Condition for maximum efficiency–
Calculation of blade height.
STEAM CONDENSERS: Requirements of steam condensing plant– Classification of condensers–
Working principle of different types– Vacuum efficiency and condenser efficiency – Air leakage, sources
and its affects- Air pump- Cooling water requirement.
UNIT–V
GAS TURBINES: Simple gas turbine plant–ideal cycle- Essential components– Parameters of
performance– Actual cycle– Regeneration, inter cooling and reheating – Closed and semi- Closed cycles–
Merits and demerits-Types of combustion chambers.
JET PROPULSION: Principle of operation– Classification of jet propulsive engines– Working principles
with schematic diagrams and representation on T-s diagram - Thrust, thrust power and propulsion
efficiency– Turbo jet engines– Needs and demands met by turbojet– Schematic diagram, thermodynamic
cycle, performance evaluation andthrust augmentation– Methods.
Text books:
1. Thermal Engineering by RK Rajput Laxmi publications (P) LTD, Tenth Edition, 01 January 2018 .
2.“Thermal Engineering”-P.L.Bellaney, Khanna publishers, Fifth Edition.
3. “Gas Turbines”–V.Ganesan,TMH, Forth Edition, 01 July 2017
References:
1.” Gas Turbines and Propulsive Systems”, P.Khajuria & S.P.Dubey, Dhanpatrai
2.” Thermal Engineering”,R.SKhurmi, JSGupta,S.Chand.
3.” Thermal Engineering”,M.L.Marthur&Mehta,Jainbros
____________________________________________________________________________________
((AUTONOMOUS)

Metal Cutting & Machine Tools
Teaching Total contact hours–60 L T P C
Prerequisite(s): Material Science, Strength of Materials 3 0 0 3
Course Objectives:
● The course provides students with fundamental knowledge and principles in material removal processes.
● To demonstrate the fundamentals of machining processes and machine tools.
● To develop knowledge and importance of metal cutting parameters.
● To develop fundamental knowledge on tool materials, cutting fluids and tool wear mechanisms
● Train in knowing the fundamental parts of various machine tools and their kinematic schemes.
Course Outcomes:

CO1: Explain the cutting tool geometry, chip formation and cutting forces.
Describe the various parts and operations of machine tools viz. lathe, shaper, planer,
CO2: drilling, boring, milling, grinding and broaching machine.
CO3: Identify various machine tools viz. lathe, shaper, planer, drilling, boring, milling and
grinding machine for various applications.
CO4: Discuss various principles and applications of jigs and fixtures .
CO5: Explain the working principles of various Non Traditional Machining.
Syllabus:
UNIT-I
FUNDAMENTALS OF MACHINING: Elementary treatment of metal cutting theory – Elements of cutting
process – Geometry of single point tool, tool signature, chip formation and types of chips – Built up edge and
its effects - Chip breakers, mechanics of orthogonal cutting – Merchant‟s circle, cutting forces, cutting speed,
feed, depth of cut, metal removal rate, tool life, heat generation in metal cutting, coolants, tool materials,
machinability, economics of metal cutting.
UNIT –II
LATHE MACHINES: Engine lathe – Working principle, specification of lathe – Types of lathe – Work
holders and tool holders –Lathe operations- Problems on taper turning and thread turning, lathe attachments,
constructional features of speed gear box and feed gear box. Turret and Capstan lathes - Tool layout. Principal
features of automatic lathes – Classification – Single spindle and multi-spindle automatic lathes – Tool layout.
SHAPING, SLOTTING AND PLANING MACHINES: Working principle– Principal parts –
Specifications, Operations performed, Machining time calculations.
UNIT – III
DRILLING AND BORING MACHINES: Working principle, specifications, types, operations
performed – Tool holding devices – Twist drill– Deep hole drilling machine - Boring Machines –
Fine Boring Machines – Jig boring machine,..
____________________________________________________________________________________
((AUTONOMOUS)
MILLING MACHINES: Working principle – Specifications – Classification of milling Machines –

Principal features of horizontal, Vertical and universal milling Machine, Machining operations, types of
cutters, geometry of milling cutters – Methods of indexing - Accessories of milling machines.
UNIT –IV
FINISHING PROCESSES: Theory of grinding – Classification of grinding machines, cylindrical and
surface grinding machines, tool and cutter grinding machines - Types of abrasives, specification and selection
of a grinding wheel. Dressing and truing of grinding wheels, Lapping, Honing.
JIGS & FIXTURES: Principles of jigs and fixtures design - Classification of jigs & fixtures,
principles of location and clamping, types of clamping devices.
UNIT - V
Introduction to Non Traditional Machining:
Classification of machining processes, Principle, Applications, Advantages and disadvantages of Ultra Sonic
Machining (USM), Abrasive Jet Machining (AJM), Electrochemical machining (ECM), , Electro Discharge
Machining (EDM), Electron Beam Machining (EBM), Laser Beam Machining (LBM), Plasma Arc
Machining(PAM).
Text Books:
1.“A Course in Workshop Technology”, B.S. Raghu Vamshi, Dhanpat Rai & Co., Vol. II, 10th Ed., 2012.
2.“Production Technology: Manufacturing Processes, Technology and Automation”, R.K. Jain, Khanna
Publishers, 6th ed., 2004.
3. Machining Technology: Machine Tools and Operations Hardcover , Helmi A. Youssef & Hassan
El- Hofy – 9 May 2008.
References:
1.“Manufacturing Technology: Metal Cutting and Machine Tools”, P.N Rao, McGraw Hill
Education, Vol. 2, 3rd ed., 2013
2. “Advanced Machining Processes”, V. K. Jain, Allied Publishers Pvt. Ltd., New Delhi, 2007
3.“Manufacturing Processes for Engineering Materials”, Serope Kalpakjian, Steven R.Schmid, Pearson
Education, 14th ed., 2016.
____________________________________________________________________________________
((AUTONOMOUS)

Fuels Combustion and Emission Control
(Department Elective-I)
Teaching Total contact hours – 64 L T P C
Prerequisite(s): Internal Combustion Engines 3 0 0 3
Course Objectives:
 To identify solid, liquid and gaseous fuels and their properties, analysis of fuels, process and handling.
 To outline thermodynamics of combustion and equilibrium compositions of gaseous fuels.
 To discuss the chemical and dynamic structure of laminar an turbulent premixed flames, diffusion, and
turbulent diffusive combustion in one and two-phase flows.
 To identify emissions from combustion and their controlling measures.
Course Outcomes:

Describe various types of fuels, combustion equations, adiabatic flame temperature and
CO1:
pollutant concentration.
CO2: Examine various properties of fuels and their analysis.
CO3: Identify the various factors responsible for laminar and turbulent flame propagation.
CO4: Use different principles of flame stabilization and ignition to design combustor.
CO5: Categorize emissions associated with combustion and identify their control techniques.
Syllabus:
UNIT-I
Fuels: Introduction - Classification of fuels – Conventional and Unconventional, Solid, Liquid, gaseous and
nuclear fuels – Origin of Coal – Analysis of coal. Coal – Carburisation, gasification and liquefaction –
Lignite: Petroleum based fuels – Problems associated with very low calorific value.
Gases: Coal gas, Blast furnace gas, Alcohols and Bio-gas.
UNIT -II
Fundamentals of Fuels: Definitions, properties and various measurements- Definitions and properties of
solid fuels- Definitions and properties of liquid and gaseous fuels- Various measurement techniques as per
standards.
UNIT- III
Thermodynamics of Combustion: Enthalpy of formation – Heating values of fuel – Adiabatic .
flame Temperature – Equilibrium composition of gaseous mixtures.
UNIT -IV
Laminar and Turbulent Flames Propagation and Structure: Flame stability – Burning velocity
of fuels – Measurement of burning velocity – Factors affecting the burning velocity. Combustion of
fuel, droplets and sprays – Combustion systems – Pulverized fuel furnaces – Fixed, entrained and
fluidised bed Systems.
____________________________________________________________________________________
((AUTONOMOUS)
UNIT -V
Environmental Considerations: Air pollution – Effects on environment, Human health etc.
Principal pollutants and their effects – Legislative measures – Methods of emission control.
Text Books:
1. Fuels and combustion / Sharma and Chander Mohan/ Tata McGraw Hill
2. Combustion / Sarkar / Mc. Graw Hill, Third edition, 2009
3. Combustion Engineering / Gary L. Berman & Kenneth W. Ragland/ Mc. Graw Hill
International Edition, 06 Dec 2007
References:
1. Combustion Fundamentals / Roger A Strehlow / McGraw Hill
2. Combustion Engineering and Fuel Technology / Shaha A.K./ Oxford and IBH.
3. Principles of Combustion / KannethK.Kuo/ Wiley and Sons.
4. An Introduction to Combustion / Stephen R. Turns/ Mc. Graw Hill International Edition.
____________________________________________________________________________________
((AUTONOMOUS)

Course Code Tribology (5th semester)
( Department Elective-I)
Prerequisite(s): Fluid Mechanics 3 0 0 3
Course Objectives:
● To provide the knowledge and importance of Tribology in Design, friction, wear and lubrication aspects
of machine components.
● To select proper grade lubricant for specific application.
● To understand the principles of lubrication, lubrication regimes, theories of hydrodynamic and the
advanced lubrication techniques.
● To introduce the concept of surface engineering and its importance in tribology.
● To understand the behaviour of Tribological components.
Course Outcomes:

CO1: Describe the viscosity and laws of fluid flow with reference to lubrication.
CO2: Examine hydrodynamic and hydrostatic properties of lubricants.
CO3: Explain the journal and slider bearings under different load carrying conditions.
Describe the oil flow through bearings under different pressures and with thermal
CO4:
equilibrium conditions.
Analyze the behavior of tribological components and measures subjected to different
CO5:
working conditions.
Syllabus:
UNIT – I
Introduction: Nature of surfaces and contact, surface topography- Friction and wear mechanisms and effect
of lubricants, methods of fluid film formation-Selection of rolling element bearings Nominal life, static and
dynamic capacity - Equivalent load- Probabilities of survival, cubic mean load – Bearing mounting details -
Preloading of bearings, condition monitoring using shock pulse method.
UNIT – II
Hydrodynamic bearings: Fundamentals of fluid film formation – Reynold‟s equation; Hydrodynamic
journal bearings – Sommerfeld number –Performance parameters – Optimum bearing with maximum load
capacity – Friction – Heat generated and heat dissipated. Hydrodynamic thrust bearings: Raimondi and Boyd
solution for hydrodynamic thrust bearings – Fixed and tilting pads, single and multiple pad bearings –
Optimum condition with largest minimum film thickness.
UNIT – III
Hydrostatic bearings: Thrust bearings – Pad coefficients – Restriction – Optimum film thickness –
Journal bearings – Design procedures- Aerostatic bearings: thrust bearings and journal bearings,
design procedure - Dry rubbing bearings Porous metal bearings and oscillatory journal bearings,
qualitative approach only.
____________________________________________________________________________________
((AUTONOMOUS)
UNIT – IV
Lubrication: Choice of lubricant type, oil, grease and solid lubricants, additives- Lubrication
systems and their selection – Selection of pump, filters, piping design, oil changing and oil
conservation.
UNIT – V
Seals: Different types, mechanical seals, lip seals, packed glands, soft piston seals, mechanical piston rod
packing, labyrinth seals and throttling bushes, oil flinger rings and drain grooves-Selection of mechanical
seals.Failure of tribological components - Failure analysis of plain bearings, rolling bearings, gears and seals,
wear analysis using SOAP and Ferrography.
Text Books:
1. Fundamentals of Tribology – S.K. Basu, S.N. Sengupta& B.B. Ahuja – PHI, 2015.
2. Engineering Tribology – Prasanta Sahoo – PHI, 2013.
References:
1. Tribology Handbook – Neale M J – Neumann Butterworths, 2016.
2. Introduction to Tribology – Bharat Bhushan ¬ – John Wiley and Sons Ltd, 2013.
3. Hydrostatic and Hybrid Bearing Design – Rowe W W& O‟ Dionoghue – Butterworths& Co.
Publishers Ltd., 2012
____________________________________________________________________________________
((AUTONOMOUS)

Course Code Industrial Robotics (5th Semester)
(Department Elective-I)
Prerequisite(s): KOM 3 0 0 3
Course Objectives:
● To understand the functions of the basic components of a Robot.
● To study the use of various types of End Effectors and Sensors.
● To impart knowledge in Robot Kinematics and Programming.
● To learn Robot safety issues and economics.
Course Outcomes:

CO1: Discuss the fundamental components and coordinate systems of different industrial robots.
CO2: Explain different types of drives used in robots and end effectors.
CO3: Describe types of sensors used in industrial robot.
CO4: Analyze the kinematics of robot arm.
CO5: Identify the suitable robot for different industrial applications with economic considerations.
Syllabus:
UNIT-I
INTRODUCTION TO ROBOTICS: Automation and Robotics - Robot – Definition – Robot anatomy –
Co ordinate systems, work envelope types and classification-Specifications-Pitch, yaw, roll, joint notations,
pay load- Robot parts and their functions-Need for robots-Different applications.
UNIT-II
ROBOT ACTUATORS AND END EFFECTORS: Pneumatic drives-Hydraulic drives-Mechanical drives-
Electrical drives-D.C. servo motors, stepper motors, A.C. servo motors-Salient features, applications and
comparison – End Effectors-Grippers-Mechanical grippers, pneumatic and hydraulic grippers, magnetic
grippers, vacuum grippers – Two fingered and three fingered grippers – Internal grippers and external
grippers – Selection and design considerations.
UNIT-III
MOTION ANALYSIS: Homogeneous transformations as applicable to rotation and translation – problems.
MANIPULATOR KINEMATICS: Specifications of matrices, D-H notation joint coordinates and world
coordinates Forward and inverse kinematics – problems.
UNIT-IV
Differential transformation and manipulators, Jacobians – problems, Dynamics: Lagrange – Euler and
Newton – Euler formulations – Problems.
FEED BACK COMPONENTS: Position Sensors – Potentiometers, Resolvers, and Encoders – Velocity
Sensors.
____________________________________________________________________________________
((AUTONOMOUS)
UNIT-V
ROBOT PROGRAMMING AND IMPLEMENTATION : Lead Through Programming, Robot
Programming Languages -VAL Programming - Motion Commands, Sensor Commands, End Effectors in
Robotics - Commands and Simple Programs - RGV, AGV; Implementation of Robots in Industries - Safety
Considerations for Robot Operations - Economic Analysis of Robots.
Text Books:
1. Groover M.P., “Industrial Robotics -Technology Programming and Applications”, McGraw Hill, 2012.
2. Klafter R.D., Chmielewski T.A and Negin M., “Robotic Engineering - An Integrated
Approach”,Prentice Hall, 1989.
References:
1. Craig J.J., “Introduction to Robotics Mechanics and Control”, Pearson Education, 2008.
2. Deb S.R., “Robotics Technology and Flexible Automation” Tata McGraw Hill Book Co.,
1994.
3. Koren Y., “Robotics for Engineers", Mc Graw Hill Book Co., 1992.
4. Fu.K.S.,Gonzalz R.C. and Lee C.S.G., “Robotics Control, Sensing, Vision and Intelligence”,
McGraw Hill Book Co., 1987.
5. Janakiraman P.A., “Robotics and Image Processing”, Tata McGraw Hill, 1995.
6. Rajput R.K., “Robotics and Industrial Automation”, S.Chand and Company, 2008.
7. Surender Kumar, “Industrial Robots and Computer Integrated Manufacturing”, Oxford and
IBH Publishing Co. Pvt. Ltd., 1991.
____________________________________________________________________________________
((AUTONOMOUS)

Course Code Advanced Materials (5th Semester)
( Department Elective-I)
Teaching Total contact hours–64 L T P C
Prerequisite(s): Metallurgy & Material Science 3 0 0 3
Course Objectives:
 To understand the concepts and need of composites in various applications.
 To learn about manufacturing of different types of composites and their properties.
 To understand the macro-mechanical analysis procedure of composite lamina.
 To understand the fundamentals of functional graded materials, shape memory alloys and nano materials.
Course Outcomes:

CO1: Discuss the composites and their classification.
CO2: Describe polymer composites and their manufacturing methods.
CO3: Analyze the mechanical behavior of composite laminates.
CO4: Investigate properties and applications of functionally graded materials and shape memory
alloys.
CO5: Explain the properties and applications of nano materials.
Syllabus:
UNIT-I
INTRODUCTION TO COMPOSITE MATERIALS: Introduction, classification- Polymer matrix
composites, metal matrix composites, ceramic matrix composites, Carbon Fibre composites, Carbon–Carbon
composites, fibre reinforced composites and nature-made composites, Properties of Composites in
comparison with standard materials and applications.
REINFORCEMENTS: Classification of Reinforcement - Fibres, Filled, Whiskers, Flake, Particulates,
Directly Solidified Eutectics.
UNIT-II
Polymer composites, thermoplastics, thermosetting plastics, manufacturing of PMC, MMC & CCC and their
applications.
MANUFACTURING METHODS: Autoclave, tape production, moulding methods, filament winding, hand
layup, Pultrusion, RTM.
UNIT-III
MACROMECHANICAL ANALYSIS OF A LAMINA: Introduction, generalized Hooke‟s law, reduction
of Hooke‟s law in three dimensions to two dimensions, Types of Laminates-Symmetric Laminates, Anti
symmetric laminate, Balanced Laminate, Quasi-Isotropic Laminates. Relationship of compliance and stiffness
matrix to engineering elastic constants of an orthotropic lamina.
UNIT-IV
____________________________________________________________________________________
((AUTONOMOUS)
FUNCTIONALLY GRADED MATERIALS: Types of functionally graded materials-Classification

different systems-Preparation-properties and applications of functionally graded materials.
SHAPE MEMORY ALLOYS: Introduction-Shape memory effect-Classification of shape memory alloys
composition-Properties and applications of shape memory alloys.
UNIT-V
NANO MATERIALS: Introduction-properties at nano scales-Advantages & disadvantages-Applications in
comparison with bulk materials ( nano – structure, wires, tubes, composites ). Special nano materials: carbon
nanotubes, fullerenes, nanowires, porous silicon. Piezoelectric materials, Electro active polymer (EAP) ,
Magnetostrictive material.
Text Books:
1. Nano material /A.K. Bandyopadyay/New age Publishers
2. Material science and Technology: A comprehensive treatment/Robert W.Cahn,/VCH
3. Engineering Mechanics of Composite Materials / Isaac and M Daniel/Oxford University Press
References:
1. Mechanics of Composite Materials / R. M. Jones/ Mc Graw Hill Company, New York, 1975.
2. Analysis of Laminated Composite Structures / L. R. Calcote/Van Nostrand Rainfold,NY 1969
3. Analysis and performance of fibre Composites /B. D. Agarwal and L. J. Broutman /Wiley-Interscience,
New York, 1980 4. Mechanics of Composite Materials - Second Edition (Mechanical Engineering) /Autar
K.Kaw / CRC Press.
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)

(5th semester)
Course Code
Theory of Machines Lab
Prerequisite(s): Engineering mechanics, Theory of machines 0 0 3 1.5

Course Objectives:
 To understand the principles of gyroscope and governors.
 To determine the frictional forces and power of brakes.
 To determine the moment of inertia of flywheel.
 To determine the static and dynamic balancing of rotating mass systems.
 To determine the frequency of free and forced vibrations of spring mass systems.
Course Outcomes:
On Completion of the course, the students will be able to

CO1: Assess the gyroscopic effect and angular displacement of cam follower.
CO2: Analyze the characteristic curves of different governors.
CO3: Illustrate about different types of gears and four bar mechanism.
CO4: Evaluate belt drives, mass balancing system.
CO5: Analyze different types of vibration systems and spring mass systems.
Syllabus:
The following experiments will be carried out:
1. Study the gyroscopic effect of a rotating disc.

2. To find out the angular displacement of various cam follower pairs.
3. Determination of characteristics curves of various governors by universal governor.
4. To study undamped free vibrations of a spring.
5. To calculate equivalent spring stiffness for springs in series.
6. To study the natural vibrations of a spring mass system.
7. To study forced damped vibration of a spring mass system.
8. To study about Simple and Compound Screw Jack and measure various parameters.
9. Determination of moment of inertia of Flywheel.
10. Determination of the whirling speed of shaft.
11. To calculate co-efficient of friction in-between the belt and pulley.
12. Study the types of Gears.
13. Study the Four Bar Mechanism.
14. To show that a two mass system statistically balanced, but not dynamically balanced.
15. To show simple dynamic balancing of a three mass system.
16. To show simple dynamic balancing of a four mass system.
17. To demonstrate balance of four bar system both statically, dynamically.
____________________________________________________________________________________
((AUTONOMOUS)

Machine Tools Lab
Prerequisite(s): Material Science, Workshop Technology 2 1 0 3
Course Objectives:
● To understand terminology and geometry of tools and various operations on lathe.
● To understand various milling operations.
● To understand operations carried out on drilling, boring and broaching machines .
● To understand operations carried out on grinding machines.
● Familiarize different machine tools used in production floor.
Course Outcomes:

Perform step and taper turning, thread cutting, knurling and boring operations on cylindrical
CO1:
work pieces using lathe machine.
Produce prismatic parts with desired surface finish using surface grinding machine and tool
CO2:
angles using tool and cutter grinder machine.
CO3: Perform indexing to machine spur gears on milling machine.
Execute sequence of operations on slotting and shaping machines to generate keyways and
CO4:
splines on the given work piece.
CO5: Carry out drilling and tapping operations to produce desired hole pattern on the given job.
Syllabus:
The following experiments will be carried out:
1. Step Turning & Taper Turning operation using Lathe Machine.
2. Knurling, Thread cutting and grooving operation using Lathe Machine.
3. Single Start Thread Cutting operation using Lathe Machine.
4. Multi Start Thread Cutting using Lathe Machine.
5. Eccentric Turning operation on Lathe Machine.
6. Surface Grinding operation on reciprocating table type horizontal spindle surface grinder.
7. Slot cutting on a Slotting Machine.
8. Key way cutting using Shaping Machine.
9. Production of Flat surface from round block using Shaping Machine.
10. Cutting Cylindrical work piece into Prismatic Bar on Shaping Machine.
____________________________________________________________________________________
((AUTONOMOUS)
11. Gear cutting using Milling Machine.
12. Contour Milling using vertical milling attachment on universal milling machine.
13. Drilling & Tapping operation using Radial Drilling Machine.
14. Measurement of cutting forces using Tool Force Dynamometer.
15. Grinding of tool angles using Tool and Cutter Grinder
16. Boring operation on Lathe Machine.
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)

GRBT-19 (Autonomous) III B.Tech. II Sem
Design of Transmission Elements
Prerequisite(s): Engineering Mechanics, Mechanics of Solids. 2 1 0 3

(Use of approved design data book is permitted in the end semester examination)
Course Objectives:
● To learn about the types of shafts, keys, coupling joints and their suitability.
● To learn about the Design and selection of journal and ball bearings to suit requirements.
● To learn about the Procedures to design the engine components like piston, connecting rod, and cylinder.
● To learn about the Procedures to design the various types of gears.
● To learn about the concepts of flexible elements.
Course Outcomes:
On Completion of the course, the students shall be able to-

CO1: Find required sizes of shaft, keys and couplings for the given application.
CO2: Identify a suitable bearing for the given application.
CO3: Design of gear for a given application.
CO4: Design of suitable I.C. engine parts for a given application.
CO5: Suggest suitable flexible elements required to transmit the desired power.
Syllabus:
UNIT-I
KEYS AND COUPLINGS: Purpose of key, different types of keys, Design – Square and flat keys,
Kennedy keys and splines, purpose of shaft couplings, different types of couplings – Design of rigid
couplings - muff coupling, split muff coupling and flanged coupling, Design of Flexible couplings - bushed-
pin flexible coupling, Oldham‟s coupling and Universal coupling.
SHAFTS: Design of solid and hollow shafts for strength and rigidity – design of shafts for combined bending
and axial loads – shaft sizes – BIS code. Use of internal and external circlips, gaskets and seals (stationary &
rotary)
UNIT-II
BEARINGS: Classification of bearings- applications, types of journal bearings – lubrication – bearing
modulus – full and partial bearings – clearance ratio – heat dissipation of bearings, bearing materials – journal
bearing design – ball and roller bearings – static loading of ball & roller bearings, bearing
UNIT- III
DESIGN OF ENGINE PARTS: Connecting Rod-Thrust in connecting rod – Stress due to whipping action
on connecting rod ends – Cranks and crank shafts, strength and proportions of over hung and centre cranks –
Crank pins, crank shafts. Pistons– forces acting on piston – construction design and proportions of piston,
cylinder– cylinder liners.
____________________________________________________________________________________
((AUTONOMOUS)
UNIT-IV
SPUR & HELICAL GEAR DRIVES: Spur gears- helical gears – load concentration factor – dynamic load
factor, surface compressive strength – bending strength – design analysis of spur gears – estimation of centre
distance, module and face width, check for plastic deformation, check for dynamic and wear considerations.
UNIT-V
DESIGN OF FLEXIBLE ELEMENTS: Belts and their construction - Flat belts versus V- belts, Open and
cross belt arrangement, Ratio of belt tensions-Centrifugal tension-Effect of centrifugal tension, Design of flat
belts and V-belts, Selection of wire rope and Pulleys, Introduction to Chain drive - its merits and demerits,
Constructional features of a chain drive.
Text Books:
1.V.B. Bhandari, Machine Design of Machine Elememts, 4/e, Tata McGraw Hill, 2017.
2.Norton, R. L., Machine Design: An Integrated Approach, 5/e, Pearson, 2013.
3.Faculty of Mechanical Engineering, Design Data: Data Book of Engineers, PSG College of Engineering,
2012
References:
1.R.S. Khurmi and J. K. Gupta, Machine design, 25/e, S.Chand Publishers, 2014.
2.T.V. Sundaramoorthy & N.Shanmugam, Machine Design, 6/e, SciTech Publishers, 2010.
3.Shigley, J.E and Mischke, C. R. Mechanical Engineering Design, 8/e, Tata McGraw Hill, 2008.
4.Design data hand book, S. Md. Jalaludeen.
____________________________________________________________________________________
((AUTONOMOUS)

GRBT-19 (Autonomous)
III B.Tech. II Sem
(6th semester)
Course Code
Industrial Engineering & Management
Teaching Total contact hours- 62 L T P C

Prerequisite(s): Manufacturing Concepts. 3 0 0 3
Course Objectives:
 To understand the concepts of Industrial Engineering and Principles of Management.
 To understand the methods for improving productivity in manufacturing industries.
 To familiarize various techniques of HRM, Quality Control, Work Study and Project Management.
Course Outcomes:

CO1: Describe the various concepts of management techniques.
CO2: Identify a suitable plant location and layout by considering various industrial aspects.
CO3: Use work study concepts to improve productivity.
CO4: Apply the suitable quality management techniques.
CO5: Assess the project duration and crashing of any network problems.
Syllabus:
UNIT – I
INTRODUCTION:
Industrial Engineering- Role of Industrial Engineer- IE Applications – Productivity – Scope of Industrial
Engineering.-Management Concepts, Origin, Importance, functions of management, F W Taylor‟s Scientific
Management, McGregor‟s theory X and theory Y– Henry Fayol‟s Management Principles-Human Resource
Management: Functions of HRM, Job-evaluation, merit rating
UNIT – II
PLANT - FACILITY LOCATION & LAY-OUT:
Factors governing plant location - Location Economics, types of sites, types of plant, Plant layout techniques
PRODUCTION –Types of Production- Advantages and disadvantages - Aggregate Production Planning.
Plant maintenance – Types – Preventive, predictive, breakdown – Reliability - Availability concepts .
UNIT – III
OPERATIONS MANAGEMENT – WORK STUDY:
Work study – Objectives of work study: Role of work study in improving productivity – Method/Motion
Study: Procedure, objectives, applications, recording techniques: charts, diagrams, graphs and models –
Micro-motion study: Procedure, objectives, applications, Therbligs – Time study/work measurement:
Procedure, objectives, applications - Time study techniques: stop watch method, PMTS, work sampling –
Concept of allowances, performance rating, estimation of standard time- Introduction to Ergonomics.
UNIT – IV
QUALITY MANAGEMENT:
____________________________________________________________________________________
((AUTONOMOUS)
Introduction to quality - Statistical quality control (SQC): Control Charts, Numerical Examples on X Bar, R
Charts, C Charts and P Charts - Sampling plans, Total Quality Management (TQM): DEMING cycle,
DMAIC Cycle, Zero Defects, Quality Circles, ISO Quality Systems, 5S, Six Sigma
MATERIALS MANAGEMENT–Inventory, basic EOQ model, Selective Inventory Control techniques –
ABC, VED, FSN, XYZ – MRP- ERP- Supply Chain Management-Value Engineering – Value Analysis.
UNIT – V
PROJECT MANAGEMENT: Introduction to Network Diagrams - CPM and PERT - Critical Path Analysis
- Activity times and floats, Project completion times. PERT and three Time Estimates, critical path analysis of
a PERT network, Probability of completion of project - Simple Numerical Examples on CPM & PERT
Project crashing.
Text Books:
1. Industrial Engineering and Management, OP Khanna, Khanna Publishers, 2018-19(17th Edition)
2. Industrial Engineering and Production management, MartandTelsang, S Chand & Co New Delhi, 2006
(2nd edition)
References:
1. Industrial Engineering and Management, M Mahajan, 2014 (2nd Edition)
2. Production and Operations Management – Paneerselvem – PHI.
3. Introduction to Work Study, I.L.O., 4th Revised Edn., 1992
4. Handbook of Industrial Engineering: Technology and Operations Management By GavrielSalvendy, A
Wiley-Interscience Publication, 2001 (Third edition)
Useful Web-links : http://nptel.ac.in/courses.php

http://mit.espe.edu.ec/courses/mechanical-engineering/
____________________________________________________________________________________
((AUTONOMOUS)

Heat Transfer
Prerequisite(s): Fundamentals of Engineering Thermodynamics 2 1 0 3
Course Objectives:
● To understand the modes of heat transfer and thermo-physical properties.
● To understand the concepts of various experimental heat transfer correlations in engineering
applications.
● To understand velocity and thermal boundary layers in convective heat transfer.
● To learn concepts of heat exchangers.
● To understand the radiation heat transfer.
Course Outcomes:

CO1: Explain the basic concepts of heat transfer.
Solve the problems involving steady state and transient heat conduction in simple
CO2:
geometries.
CO3: Analyze the forced and free convective heat transfer through various systems.
Analyze the performance of heat exchangers and evaporators using boiling and condensation
CO4:
principles.
CO5: Illustrate the real time applications of radiation heat transfer.
Syllabus:
UNIT-I
INTRODUCTION: Modes and mechanisms of heat transfer – Basic laws of heat transfer –General
discussion about applications of heat transfer.
CONDUCTION HEAT TRANSFER: Fourier rate equation – General heat conduction equation in
cartesian, cylindrical and spherical coordinates. Steady, unsteady and periodic heat transfer – Initial and
boundary conditions.
ONE DIMENSIONAL STEADY STATE CONDUCTION HEAT TRANSFER: Homogeneous slabs,
hollow cylinders and spheres – Overall heat transfer coefficient – Electrical analogy – Critical radius of
insulation- Variable thermal conductivity – Systems with heat sources and heat generation.
UNIT -II
Extended surface (fins) heat Transfer: Long fin, fin with insulated tip and short fin, application to error
measurement of temperature.
ONE DIMENSIONAL TRANSIENT CONDUCTION HEAT TRANSFER: Systems with negligible
internal resistance – Significance of biot and Fourier numbers - Chart solutions of transient conduction
systems.
CONVECTIVE HEAT TRANSFER: Classification of convective heat transfer , dimensional analysis as a
tool for experimental investigation – Buckingham Pi Theorem for forced and free convection, application for
developing semi , empirical non- dimensional correlation for convective heat transfer – Significance of non-
dimensional numbers – Concepts of continuity, Momentum and Energy Equations.
____________________________________________________________________________________
((AUTONOMOUS)
UNIT- III
FORCED CONVECTION
EXTERNAL FLOWS: Concepts about hydrodynamic and thermal boundary layer and use of empirical
correlations for convective heat transfer-flat plates and cylinders.
INTERNAL FLOWS: Concepts about hydrodynamic and thermal entry lengths, division of internal flow
based on this– Use of empirical relations for horizontal pipe flow and annulus flow.
FREE CONVECTION: Development of hydrodynamic and thermal boundary layer along a vertical plate –
Use of empirical relations for vertical plates and pipes.
UNIT -IV
BOILING: Pool boiling – Regimes, calculations on nucleate boiling, critical heat flux and film boiling.
CONDENSATION: Film wise and drop wise condensation –Nusselt‟s theory of condensation on a vertical
plate - Film condensation on vertical and horizontal cylinders using empirical correlations.
HEAT EXCHANGERS: Classification of heat exchangers –Overall heat transfer coefficient and fouling
factor – Concepts of LMTD and NTU methods – Problems.
.
UNIT -V
RADIATION HEAT TRANSFER:
Emission characteristics and laws of black ,body radiation – Irradiation – total and monochromatic quantities
– Laws of Planck, Wien, Kirchoff, Lambert, Stefan and Boltzmann– Heat exchange between two black bodies
– Concepts of shape factor – Emissivity – Heat exchange between grey bodies – Radiation shields – Electrical
analogy for radiation networks.
Text books:
1. Heat Transfer/JP HOLMAN/TMH/10thediton
2. Heat Transfer/P.K.Nag,/TMH/3rd edition /2011
Reference books:
1.Heat and Mass Transfer/Yunus A Cengel; Afshin J. Ghajar/McGraw-Hill/ 5th edition/ 2017
2. Heat and Mass Transfer/ D.S. Kumar, S.K. Kataria&Sons./2013
3. Heat and Mass Transfer/Arora and Domkundwar,Dhanpatrai& sons/2007
4. Fundamentals of Engg. Heat and Mass Transfer/R.C.Sachdeva/New Age Science/2009
5.Heat and Mass Transfer/R.K.Rajput/S. Chand Publishing/2019
____________________________________________________________________________________
((AUTONOMOUS)

Metrology and Instrumentation
Prerequisite(s): 3 0 0 3
Course Objectives:
1. To understand selection of fits and tolerances in manufacturing industry.
2. To develop the basic knowledge on linear and angular measurements and their standards of
measurements.
3. To learn about different techniques to measure surface finish, flatness, gear and screw thread
parameters.
4. To understand principle and operation of comparators and machine tool alignment tests.
5. To understand the construction and working principle of measuring instruments of displacement,
temperature, speed, flow and pressure.
6. To understand the construction and working principle of stress and strain measuring instruments and
concept of control systems.
Course Outcomes:

CO1: Examine the tolerances, limits and fits of engineering components.
CO2: Describe linear, angular measuring instruments comparators and limit gauges.
CO3: Discuss surface roughness, gear and screw thread measurements.
Explain instruments for measurement of displacement, temperature, pressure, speed and flow
CO4:
parameters.
CO5: Use instruments for measurement of stress and strain, fluid flow, torque and power.
Syllabus
UNIT-I
SYSTEMS OF LIMITS AND FITS: Introduction - limits, fits – tolerances ,deviations, Unilateral and
bilateral tolerance system, hole and shaft basis systems- interchangeability and selective assembly -
International standard system of tolerances.
LIMIT GAUGES AND GAUGE DESIGN: Taylor‟s principle – design of go and no go gauges - plug,
ring, snap, gap, taper, profile and position gauges.
COMPARATORS: Working principle and uses - Types ,mechanical, optical, electrical and electronic,
pneumatic comparators.
UNIT-II
LINEAR MEASUREMENTS: Line standards, end standards - slip gauges, calibration of the slip gauges,
dial indicators, micrometers, vernier calipers.
MEASUREMENT OF ANGLES AND TAPERS: Bevel protractor, angle slip gauges, angle dekkor, spirit
levels, sine bar, rollers and spheres used to measure angles and tapers.
FLATNESS MEASUREMENT :Measurement of flatness of surfaces- straight edges,surface plates, auto
collimator.
____________________________________________________________________________________
((AUTONOMOUS)
UNIT – III
SURFACE ROUGHNESS MEASUREMENT: Differences between surface roughness and surface
waviness –Numerical assessment of surface finish, Centre line average, Root mean square method, Method of
measurement of surface finish – Profilograph, Talysurf, ISI symbols for indication of surface finish.
GEAR MEASUREMENT: Nomenclature of gear tooth, tooth thickness measurement with gear tooth
vernier & flange micro meter, pitch measurement, rolling gear tester, involute profile checking.
SCREW THREAD MEASUREMENT: Elements of screw parameters – errors in screw threads-
measurement of effective diameter, two wire and three wire methods.
MACHINE TOOL ALIGNMENT TESTS: Requirements of alignment tool tests -instruments used -
Alignment tool tests on lathe, drilling and Milling machines.
UNIT – IV
Definition – Basic principles of measurement – measurement systems– Types of errors.
MEASUREMENT OF DISPLACEMENT: Working principle of transducers, types, LVDT, piezo electric,
inductive, capacitance, resistance transducers.
MEASUREMENT OF TEMPERATURE: Classification, principles of measurement – expansion,
electrical resistance, thermistor ,thermocouple, pyrometers, temperature indicators.
MEASUREMENT OF PRESSURE: Working principle of Manometers, Bourdon pressure gauges, bellows
– diaphragm gauges and Low pressure measurement, thermal conductivity gauges ,McLeod pressure gauge.
MEASUREMENT OF SPEED: Mechanical tachometers – electrical tachometers – stroboscope, non-
contact type of tachometers, principles of seismic instruments – vibrometer and accelerometer using this
principle.
UNIT – V
FLOW MEASUREMENT: Magnetic, ultrasonic, turbine flow meter, hotwire anemometer, laser Doppler
anemometer (LDA).
STRESS STRAIN MEASUREMENTS: Working principle of Electrical strain gauges – method of usage of
resistance strain gauge for bending compressive and tensile strains , strain gauge rosettes.
MEASUREMENT OF FORCE, TORQUE AND POWER: Principle and working of Elastic force meters,
load cells, torsion meters, dynamometers, proving ring.
ELEMENTS OF CONTROL SYSTEMS: Introduction, importance – classification – open and closed
systems.
Text Books:
1. R.K.Jain, Engineering Metrology”,Khanna Publishers, New Delhi 2018.
2. Dr.D.S.Kumar ,Mechanical Measurement and Control, Metropolitan book co,New
Delhi 2019.
References
1. Doeblin Earnest, O.Adaptation, Manik, Dhanesh,Measurement systems: Application and
Design Tata McGraw– Hill, New Delhi, Fifth edition, 2007.
2. J.P.Holman, Experimental Methods for Engineers, McGraw- Hill,New Delhi Eight edition,
2011.
3. M. Mahajan, Text book of Metrology, DhanapatiRai publications, New Delhi 2007.
____________________________________________________________________________________
((AUTONOMOUS)
Regulation
Godavari Institute of Engineering & Technology (Autonomous)
GRBT-19 III B.Tech. II Sem
Course Code Refrigeration and Air-Conditioning (6th semester)
( Department Elective-II)
Prerequisite(s): Thermodynamics and Thermal Engineering 2 1 0 3
Course Objectives:
 To learn the fundamental concepts of refrigeration and air conditioning.
 To study various refrigeration cycles and evaluate their performance using Mollier charts.
 To compare properties, applications and environmental issues of different refrigerants.
 To understand the basic concepts of air conditioning processes and its applications.
 To study the various equipments of refrigeration air conditioning systems.
Course Outcomes:

CO1: Describe the concepts and applications of refrigeration systems.
Compare & contrast the performance of vapor compression and absorption refrigeration
CO2:
system.
CO3: Explain steam jet refrigeration system and their components.
CO4: Discuss various refrigerants and components used in refrigeration plants.
CO5: Classify air conditioning systems and assess their performance.
Syllabus:
UNIT-I
INTRODUCTION TO REFRIGERATION: Necessity and applications – unit of refrigeration and
COP.–Mechanical refrigeration – types of ideal cycles of refrigeration. Air refrigeration: Bell-Coleman
cycle - open and dense air systems – refrigeration systems used in air-crafts and problems.
UNIT- II
VAPOUR COMPRESSION REFRIGERATION: Simple vapour compression refrigeration cycle –
COP – representation of cycle on T-s and P-h charts – effect of sub-cooling and super heating – cycle
analysis – use of p-h charts – numerical problems.
VAPOR ABSORPTION SYSTEM: Calculation of maximum COP – description and working of NH3 –
water system and Li Br –water (Two shell & Four shell) System, principle of operation three fluid
absorption system.
UNIT- III
STEAM JET REFRIGERATION SYSTEM: Working Principle and basic components. Principle and
operation of (i) Thermoelectric refrigerator (ii) Vortex tube.
REFRIGERANTS: Desirable properties – classification of refrigerants -azeotrops– nomenclature –
secondary refrigerants –effect on ozone depletion– lubricants.
REFRIGERATION EQUIPMENTS: Compressors- Types of compressors. Condensers – Types of
condensers. Evaporators – Types of Evaporators. Expansion Devices – Types of expansion devices.
____________________________________________________________________________________
((AUTONOMOUS)
UNIT – IV
INTRODUCTION TO AIR- CONDITIONING: Psychometric Properties & Processes– Relations–
Characterization of Sensible heat and latent heat loads – Heat load concepts: RSHF, GSHF –Problems.
Requirement of the human comfort – Concept of Effective Temperature – Comfort Chart – Comfort Air-
Conditioning, Need for ventilation, Consideration of Infiltrated air.
UNIT – V
AIR-CONDITIONING EQUIPMENTS AND APPLICATIONS: Humidifiers–Dehumidifiers – Air
filters–fans and blowers, grills and registers, ducts–supply ducts–outlets–return outlets.
A/C SYSTEMS - Summer A/C,Winter A/C, Year round A/C, Central A/C, Unitary A/C systems.
Text Books:
1.“A Course in Refrigeration and Air Conditioning”, S.C. Arora & Domkundwar, DhanapatRai
Publications, New Delhi.
2.“Refrigeration and Air Conditioning”, C.P. Arora, Tata McGraw Hill.
References:
1.“A Text book of Refrigeration and Air-Conditioning”, R S Khurmi, S C Chand Publications.
2.“Refrigeration and Air Conditioning”, Manohar Prasad, New Age Publishers.
3.“Refrigeration and Air Conditioning”, Wilbert F. Stoecker, Jerold W. Jones, McGraw Hill,
1982.
____________________________________________________________________________________
((AUTONOMOUS)

Course Code Mechatronics (6th Semester)
Prerequisite(s): Basic Electrical and Electronics Engineering 3 0 0 3
Course Objectives:
● To understand the elements and techniques involved in mechatronics systems.
● To learn the concepts of actuators and their uses.
● To understand the applications of microprocessors and microcontrollers in mechanical systems.
● To learn architecture and system interface of analog and digital convertors.
● To understand the concept of PLC system and its programming, and its significance.
Course Outcomes:

CO1: Discuss the key elements of mechatronic system.
CO2: Outline various sensors and actuators for an engineering application.
CO3: Describe various microprocessors and microcontrollers.
Use appropriate microprocessor and microcontroller for interfacing sensors, actuators and
CO4:
other mechatronic elements.
CO5: Construct PLC program and implementation of real life systems.
Syllabus:
UNIT- I
INTRODUCTION: Mechatronics systems – Elements & levels of mechatronics system, mechatronics design
process - System, measurement systems, control systems, microprocessor-based controllers, advantages and
disadvantages of mechatronics systems. Sensors and transducers, types, static and dynamic characteristics of
sensor - Potentiometers – LVDT – Capacitance sensors – Strain gauges – Eddy current sensor – Hall effect
sensor – Temperature sensors – Light sensors.
UNIT –II
ACTUATORS : Hydraulic and pneumatic systems, components, control valves, electro- pneumatic,
hydro-pneumatic, electro-hydraulic servo systems. Mechanical actuating systems, basic principles and
elements. Electrical actuating system, types of stepper and servo motors – Construction – Working Principle –
Advantages and Disadvantages.
UNIT- III
MICROPROCESSOR AND MICROCONTROLLER: Introduction – Architecture of 8085 – Pin
Configuration – Addressing Modes –Instruction set – Timing diagram of 8085 – Concepts of 8051
microcontroller – Block diagram.
UNIT -IV
____________________________________________________________________________________
((AUTONOMOUS)
SYSTEM INTERFACING: Introduction – Architecture of 8255, keyboard interfacing, LED display

interfacing, analog to digital convertor and digital to analog convertor interface – Temperature Control –
Stepper Motor Control – Traffic Control interface.
UNIT -V
PLC AND MECHATRONIC SYSTEM DESIGN : Introduction – Basic structure – Input and output
processing – Programming – Mnemonics – Timers, counters and internal relays – Data handling – Selection
of PLC.Design process-stages of design process – Traditional and mechatronics design concepts – Case
studies of mechatronics systems – Pick and place robot – Engine management system – Automatic car park
barrier.
Text Books:
1. Bolton, “Mechatronics”, 5 th Edition, Pearson Education India, 2011
2. Ramesh S Gaonkar, “Microprocessor Architecture, Programming, and Applications with the 8085”, 6
th Edition, Penram International Publishing Pvt. Ltd, 2013.
References:
1. Bradley D.A, Dawson D, Buru N.C and Loader A.J, “Mechatronics”, Chapman and Hall, 1993.
2. Clarence W, de Silva, "Mechatronics" CRC Press, First Indian Re-print, 2013
3. Devadas Shetty and Richard A. Kolk, “Mechatronics Systems Design”, PWS publishing company,
2007.
4. Krishna Kant, “Microprocessors & Microcontrollers”, Prentice Hall of India, 2007.
5. Michael B.Histand and Davis G.Alciatore, “Introduction to Mechatronics and Measurement systems”,
McGraw Hill International edition, 2007.
____________________________________________________________________________________
((AUTONOMOUS)

(6th semester)
Course Code Advanced Foundry and Welding Technology
Prerequisite(s): Manufacturing Technology 3 0 0 3
Course Objectives:
● Familiarize the concepts related to moulding techniques.
● To understand the industrial practice, and their comparative merits and demerits.
● To gain knowledge on various advanced welding processes so that the students can apply them in
engineering industry applications.
● To gain knowledge on the design of welded joints and the quality control of weldments.
Course Outcomes:

CO1: Describe various moulding techniques.
CO2: Explain the principles of solidification and melting.
CO3: Apply the knowledge of solid state welding process for engineering applications.
CO4: Discuss the various advanced welding techniques.
CO5: Identify the optimal welding process parameters for any welded joint.
Syllabus:
Unit-I
Moulding and Casting: Development of metal castings- Materials for moulding- Foundry sand control, core
making processes- Materials for core making- Different types of cores- Moulding and core making
machines. Recent developments in core and mould making- Cold set process, Investment casting- Shell
moulding- Continuous casting; Hot box method- Shaw process. Vacuum moulding for mass production.
Unit-II
Melting and Solidification: Furnaces used in foundry for melting ferrous and nonferrous metals- principals
of operation of cupola and charge calculations. Principles of Solidification: Nucleation- Crystal growth-
Morphology and structure of cast metals and alloys- Pure metals- Single phase alloys and eutectics.
Solidification in sand and chill moulds. Family of cast irons, Production of malleable and S.G. Irons-
Methods of alloying and inoculants and their effects on the structure and properties of cast iron.
Foundry Mechanization: Layout for ferrous and nonferrous foundries- Description of equipment used for
mechanization- Sand conditioners- Conveyors- Cranes- Equipment for handling moulds, Cores and molten
metal- Knock out of moulds- Fettling equipment.
Unit-III
SOLID STATE WELDING PROCESSES: Fundamental principles- Survey of the various pressure
welding processes and their applications-Friction, friction stir, explosive, diffusion, and Ultrasonic welding –
Principles of operation- Process characteristics and application.
____________________________________________________________________________________
((AUTONOMOUS)
Unit-IV
ELECTRON AND LASER BEAM WELDING: Heat generation and regulation- Equipment details in
typical set-up -Electron beam welding in different degrees of vacuum, advantages and disadvantages,
applications- Laser Welding: Principles of operation, advantages and limitations, applications.
PLASMA WELDING : Special features of plasma arc- transferred and non-transferred arc, key hole and
puddle-in mode of operation - Micro low and high current plasma arc welding and their applications, plasma
cutting, surfacing and app.
Unit -V
TESTING AND DESIGN OF WELDMENTS: Design and quality control of welds - Edge preparation
types of joints, welding symbols. Stresses in butt and fillet welds – weld size calculations - Design for
fatigue - Testing – tensile, bend hardness - Impact, notch and fatigue tests -Life assessment of weldments.
Text Books:
1. Principles of Foundry Technology, by Jain P.L-TMH Publications,2017.
2.Welding Engineering and Technology, by R.S. Parmar -Khanna Publications,2013.
References:
1. Foundry Engineering by R. L Agarwal,T. R Banga-Khanna Publications,1987.
2. Foundry Engineering by Howard F. Taylor& Others-Wiley Publications,1993.
3.Principles of Metal Castings by Heine & Others(2017).
4. Modern Welding Technology by Howard B. Cary, Scott Helzer- Pearson publications,2004.
5. Welding Metallurgy S.Kou, 2ndedition, John Wiley and Sons, New York, NY ,2003.
____________________________________________________________________________________
((AUTONOMOUS)

GRBT-19 (Autonomous) III B. Tech. II Sem.
Course Code Non Destructive Evaluation (6th semester)
Teaching Total contact hours - 64 L T P C
Prerequisite(s): Engineering Physics 2 1 0 3
Course Objectives:
 To learn about the basic principles and techniques of various NDE methods such as Visual, Penetrant
Testing, Magnetic Particle Testing, Ultrasonic Testing, Radiography, Eddy Current.
 To learn the advantages, limitations and applications of Non-destructive testing methods.
 To identify the appropriate NDE methods.
 To create awareness related to recent developments and future trends in NDE.
Course Outcomes:

CO1: Compare destructive testing and non destructive evaluation methods.
Discuss working principle and construction details of magnetic particle, liquid penetrant and
CO2:
eddy current test.
CO3: Explain the working principle and construction details and methods of ultrasonic test.
CO4: Describe the working principle and construction details and methods of radiography test.
CO5: Plan the suitable NDE methods based on the required application.
Syllabus:
UNIT – I
Introduction to Non-destructive testing: Introduction to Material Testing, classification of material testing,
comparison between destructive testing and NDT –Discontinuities, origin and classification of discontinuities
– Importance of NDT, scope and limitations of NDT – Visual inspection, unaided and aided, visual inspection
aids.
Liquid Penetrant Test: Basic Principle – Liquid penetrant system, types and properties of liquid penetrant
and developers – TestProcedure – Interpretation of results – Effectiveness and Limitations of Liquid Penetrant
Testing – Applications of Liquid Penetrant Testing.
UNIT – II
Magnetic Particle Testing- Theory of magnetism – Magnetization of Materials, different methods of
Magnetization – Demagnetization of Materials – Magnetic Particle Test principle, equipment, test procedure –
Interpretation and evaluation of test indications – Effectiveness and Limitations of Magnetic particle testing,
Applications.
UNIT – III
Ultrasonic Testing: Basic principles of sound wave propagation, types of sound waves, sound field –
Principle of ultrasonic testing – Ultrasonic transducers, piezoelectric materials, various types of
transducers/probe – Equipment for ultrasonic testing – Pulse-echo method, transmission method, resonance
method – Different ultrasonic inspection techniques – Data representation, A/Scan, B/scan, C/scan–
Applications and limitations.
UNIT – IV
____________________________________________________________________________________
((AUTONOMOUS)
Radiography Testing: Basic Principle – Sources of X and Gamma Rays and their interaction with Matter –
Imaging, film and film less techniques – Types and use of filters and screens – geometric factors, inverse
square law – Characteristics of films, graininess, density, speed, contrast, characteristic curves, penetrameters
– Exposure charts – Radiographic equivalence– Fluoroscopy, Xero-Radiography, Computed Radiography,
Computed Tomography.
UNIT – V
Eddy Current Testing: Generation of eddy currents – Properties of eddy currents – Eddy Current Test
System, Sensing elements, Probes, Instrumentation, Types of arrangement – Interpretation/Evaluation of test
results – Applications, effectiveness and limitations.
Industrial Applications of NDT: Comparison and selection of NDT methods –Span of NDT Activities and
its industrial applications.
TEXT BOOKS:
1. “Practical Non-Destructive Testing”, Baldev Raj, T. Jayakumar, M.Thavasimuthu, Narosa Publishing
House, 3rd Edition, 2019.
2. “Non-destructive test and evaluation of Materials,” J Prasad, GCK Nair, TMH Publishers, 2nd ed.,
2011.
REFERENCES:
1. “ASM Handbook: Non Destructive Evaluation of Materials” Aquil Ahmed and Leonard J Bond, ASM
International, Volume 17, 2018.
2. “Non-destructive Hand Book” – R. Hamchand, McGraw-Hill Education; 2ndedition, 2012.
3. “Ultrasonic Nondestructive testing of Materials”, Karl Langenberg, Klaus Mayer, CRC Press; 4th
edition, 1st edition,2017.
4. “Non-destructive testing”, Warress, JMCGonmade, AIRWALK PUBLICATIONS, 1 edition, 2017.
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)

(6th semester)
Course Code
Heat Transfer Lab
Teaching Total Contact hours-55 L T P C
Prerequisite(s): Thermo Dynamics and Fluid Mechanics 0 0 0 3
Course Objectives:
 To understand the various modes of heat transfer and their applications in real life problems.
 To understand the concepts of overall heat transfer coefficient in various geometries using conduction
heat transfer.
 To learn the estimation of heat transfer in free and forced convection.
 To learn the concepts of radiation heat transfer.
Course Outcomes:

CO1: Evaluate the conduction, convection and radiation heat transfer through experiments.
Analyze the problems involving steady state and transient heat conduction in simple
CO2:
geometries.
CO3: Evaluate heat transfer coefficients for natural convection and forced convection.
CO4: Estimate the LMTD of heat exchanger.
CO5: Evaluate the Stefan Boltzmann constant and emissivity of different bodies in radiation.
Syllabus:
1. Determination of overall heat transfer co-efficient of a composite slab.

2. Determination of heat transfer rate through a lagged pipe.
3. Determination of thermal conductivity of a metal rod.
4. Determination of heat transfer coefficient in natural convection.
5. Determination of heat transfer coefficient in forced convection.
6. Determination of effectiveness of parallel and counter flow heat exchangers.
7. Determination of emissivity of a given surface.
8. Determination of Stefan Boltzmann constant.
9. Determination of heat transfer rate in drop and film wise condensation.
10. Determination of critical heat flux.
11. Demonstration of heat pipe.
12. Study of two – phase flow.
13. Determination of thermal conductivity of an insulating powder.
14. Determination of the heat transfer coefficient, fin efficiency and temperature distribution
of a pin-fin in natural convection.
15. Determination of the heat transfer coefficient, fin efficiency and temperature distribution
of a pin-fin in forced convection.
16. Determination of Heat transfer coefficient of horizontal tube in natural convection.
____________________________________________________________________________________
((AUTONOMOUS)

Metrology and Instrumentation Lab
Teaching Total Contact hours-55 L T P C
Prerequisite(s): Engineering Physics, Metrology and Instrumentation. 0 0 0 3
Course Objectives:
 Able to learn the use of various measuring instruments like sine bar , bevel protractor, slip gauges , dial
indicators and spirit level
 Able to learn the calibration process of measuring instruments.
 Able to measure the parameters of temperature, pressure, fluid flow and displacement by using different
instruments.
Course Outcomes:

Measure the linear and angular dimensions of components using vernier calipers, outside
CO1:
micrometers , bevel protractor, sine bar and transducers etc.
CO2: Assess the accuracy and errors of measuring instruments.
CO3: Check the machine tool alignment using dial indictors and spirit level.
CO4: Calibrate instruments to measure fluid flow, temperature, speed, pressure and displacement.
CO5: Investigate the vibration parameters using vibrometers.
Note: The students have to conduct at least 8 experiments from each lab.
METROLOGY LAB
1. Measurement of lengths, heights, diameters using vernier callipers, micrometers.
2. Measurement of gear parameters using gear tooth vernier.
3. Measurement of cylinder bore using inside micrometers and bore gauge.
4. Machine tool alignment test on the lathe.
5. Machine tool alignment test on drilling machine.
6. Machine tool alignment test on milling machine.
7. Angle and taper measurements with bevel protractor, Sine bar.
8. Use of spirit level in finding the straightness of a bed and flatness of a surface.
9. Measurements using Optical Projector / Toolmaker Microscope.
INSTRUMENTATION LAB
1. Calibration of transducer for temperature measurement.
2. Study and calibration of LVDT transducer for displacement measurement.
3. Calibration of strain gauge.
4. Calibration of thermocouple.
5. Calibration of capacitive transducer.
6. Study and calibration of photo and magnetic speed pickups.
7. Calibration of resistance temperature detector.
8. Study and calibration of a rotameter.
9. Study and calibration of Mcleod gauge for low pressure.
____________________________________________________________________________________
((AUTONOMOUS)

GRBT-19 (Autonomous) IV B.Tech. I Sem
(7th Semester)
Course Code Finite Element Methods
Prerequisite(s): Engineering Mathematics, Strength of Materials, , Heat 1 0 3

2
transfer, CAD/CAM.
Course Objectives:
● To learn basic concepts of finite element analysis.

● To learn the theory and characteristics of finite elements that represent engineering structures.
● To Learn the method of solving a characteristic equation of given problem.
● To learn and apply finite element solutions to structural, thermal and dynamic problems.
● To impart skills needed to effectively evaluate finite element analyses.
Course Outcomes:

CO1: Illustrate the concepts behind variational and weighted residual methods in FEM.
CO2: Analyze the applications and characteristics of finite element modeling.
CO3: Investigate element characteristic equation and generate global stiffness matrix.
Apply suitable boundary conditions to a global structural matrix equation and reduce it to
CO4:
solvable form.
Identify an appropriate FEM approach to solve problems involving dynamics and heat
CO5:
transfer.
Syllabus:
UNIT-I
INTRODUCTION TO FINITE ELEMENT METHODS: Stresses and Equilibrium – Strain-Displacement
Relations – Stress-Strain Relations, Plane Stress and Plane Strain Conditions – Variational and Weighted
Residual Methods – Concept Of Potential Energy.
STATIC ANALYSIS: One Dimensional Problems – Discretization Of Domain, Element Shapes –
Discretization Procedures – Assembly Of Stiffness Matrix, Band Width, Node Numbering – Mesh Generation
– Interpolation Functions – Local and Global Coordinates, Convergence Requirements – Treatment Of
Boundary Conditions.
UNIT -II
ANALYSIS OF TRUSSES: Finite Element Modeling – Coordinates and Shape Functions – Assembly Of
Global Stiffness Matrix and Load Vector – Finite Element Equations – Treatment of Boundary Conditions –
Stress, Strain And Support Reaction Calculations.
ANALYSIS OF BEAMS: Element Stiffness Matrix for Hermite Beam Element – Derivation Of Load Vector
For Concentrated And Udl – Simple Problems On Beams.
UNIT- III
TWO DIMENSIONAL PROBLEMS: Finite Element Modeling of Two Dimensional Stress Analysis with
Constant Strain Triangles And Treatment of Boundary Conditions.
AXISYMMETRIC PROBLEMS: Introduction – Axisymmetric Formulation – Finite Element modeling:
Types of elements, triangular element.
____________________________________________________________________________________
((AUTONOMOUS)
UNIT -IV
HIGHER ORDER AND ISO-PARAMETRIC ELEMENTS: One Dimensional Quadratic and Cubic
Elements in Natural Coordinates – Two Dimensional Four Noded Iso-Parametric Elements and Numerical
Integration.
UNIT -V
STEADY STATE HEAT TRANSFER ANALYSIS: One Dimensional Analysis of A Fin and Two
Dimensional Analysis of Thin Plate – Analysis of A Uniform Shaft Subjected To Torsion.
DYNAMIC ANALYSIS: Formulation of Finite Element Model – Element Consistent and Lumped Mass
Matrices – Evaluation of Eigen Values and Eigen Vectors – Free Vibration Analysis.
Text Books:
1. Introduction to Finite Elements in Engineering, Tirupathi R. Chandrupatla, Ashok D.Belegundu, Fourth
Edition, Pearson education, 2011.
2. Finite Element Analysis by Md.S.Jalaluddin.
3. The Finite element method in engineering, S.S.Rao, 5th edition, Elsevier publications, 2010.
References:
1. Finite element analysis, S.S. Bhavikatti, New Age International, 2005.
2. Finite Element Analysis: Theory and Programming, C.S. Krishnamoorthy, Tata McGrawHill Education,
1995.
3. An introduction to the Finite element method, JN Reddy, McGraw Hill Education, 3rd edition, 2005.
____________________________________________________________________________________
((AUTONOMOUS)

CAD/CAM
Prerequisite(s): Computer Graphics 3 0 0 3
Course Objectives:
 To learn the basic concepts of computer aided design / manufacturing.
• To understand geometric modeling and manipulation methods.
• To familiarize with the part programming of NC and CNC machines.
• To Understand and concepts of Group Technology, CAQC, FMS and CIM.
Course Outcomes:

CO1: Explain the basic concepts of CAD and Computer graphics.
CO2: Use the mathematical models to represent various geometries.
CO3: Compose the part programs for engineering components.
CO4: Explain the concepts of Group Technology and Computer Aided Quality Control.
CO5: Discuss the elements of Flexible Manufacturing Systems and Computer Integrated
Manufacturing .
Syllabus:
UNIT – I
Computers in industrial manufacturing, product cycle, CAD / CAM Hardware, basic
structure, CPU, memory types, input devices, display devices, hard copy devices, storage
devices.
COMPUTER GRAPHICS: Raster scan graphics coordinate system, database structure
for graphics modeling, transformation of geometry, 3D transformations, mathematics of
projections, clipping, hidden surface removal.
UNIT -II
GEOMETRIC MODELING: Requirements, geometric models, geometric construction
models, curve representation methods, surface representation methods, modeling facilities
desired.
DRAFTING AND MODELING SYSTEMS: Basic geometric commands, layers, display
control commands, editing, dimensioning, solid modeling.
UNIT – III
PART PROGRAMMING FOR NC MACHINES: NC, NC modes, NC elements, CNC
machine tools, structure of CNC machine tools, features of Machining center, turning
center, CNC Part Programming: fundamentals, manual part programming methods, Automatically
Programmed Tools(APT),Computer Aided Part Programming, Direct Numerical Control, Adaptive Control.
____________________________________________________________________________________
((AUTONOMOUS)
UNIT –I V
GROUP TECHNOLOGY: Part family, coding and classification, production flow
analysis, types and advantages. Computer aided processes planning – importance, types
COMPUTER AIDED QUALITY CONTROL: Terminology used in quality control, use
of computers in Quality control. Inspection methods- contact and noncontact types,
computer aided testing.
UNIT – V
FLEXIBLE MANUFACTURING SYSTEMS: Introduction to FMS– Development of manufacturing
systems – Benefits – Major elements – Types of flexibility – FMS application.
COMPUTER INTEGRATED MANUFACTURING SYSTEM: Types of manufacturing system,
material handling systems, material requirement planning, computer control systems, human labor in
manufacturing systems, CIM benefits.
Text Books:
1.“CAD/CAM” E Zimmers & M.P Groover, Pearson,1st edition,2003.
2.“Automation, Production systems & Computer integrated Manufacturing” M.P Groover, Pearson,4th
edition,2016.
References:
1.“CAD / CAM Theory and Practice”, Ibrahim Zeid & R. Sivasubrmnin, Mc grw Higher Ed, 1st edition,
2003.
2.“Principles of Computer Aided Design and Manufacturing”, Farid Amirouche,Prentice Hall, , 2nd
edition, 2004.
3.“Computer Numerical Control Concepts and programming”, Warren S Seames, Delmar Cengage
Learning, 4th edition,2001.
“
4. Product manufacturing and cost estimation using CAD/CAE”, Kuang Hua Chang, Elsevier, 1st
edition, 2013.
____________________________________________________________________________________
((AUTONOMOUS)

Course Code Power Plant Engineering (7th semester)
(Department Elective-III)
Prerequisite(s): Thermal Engineering 3 0 0 3
Course Objectives:
gain the basic knowledge on power plants operating with various energy sources.
understand diesel, gas and hydro electric power plant elements and their operations.
discuss the nuclear power plant operation using various reactors.
compare various combined plants and usage of instruments to measure various pollutants.
understand power plant economics and impact on environment.
Course Outcomes:

CO1: Illustrate various power plant layouts and their working principles.
CO2: Describe various elements involved in different power plants.
CO3: Explain Nuclear power plants with various reactors.
CO4: Analyze various combined plants and find importance of measurement of pollutants.
CO5: Evaluate economic parameters and pollutants and their prevention.
Syllabus
UNIT - I
INTRODUCTION: Introduction to the sources of energy - Resources and Development of power in India –
Power generation concepts.
STEAM POWER PLANT: Plant layout, design of plant layout, working of different circuits, fuel and
handling equipment‟s, coal handling, coal storage, ash handling systems. Coal combustion: Properties of coal
- Overfeed and Underfeed fuel beds, traveling grate stokers, spreader stokers, retort stokers, pulverized fuel
burning system and its components, advantages & disadvantages, - Ball mills – Bowl mills - Combustion
needs and draught system, cyclone furnace, design and construction, dust collectors, ESPs - Cooling towers -
and Feed water treatment..
UNIT - II
DIESEL POWER PLANT: Plant layout with auxiliaries - Fuel supply system, air starting equipment, super
charging – Advantages and Disadvantages.
GAS TURBINE PLANT: Introduction – Components of gas turbine - Classification – Gas power plant
layout with auxiliaries, combined cycle power plants and comparison.
HYDRO ELECTRIC POWER PLANT: Water power - Hydrological cycle - Flow measurement - Drainage
area characteristics - Hydrographs - Storage and Pondage - Classification of dams and spill ways – Typical
hydro electric power plant operation.
HYDRO PROJECTS AND PLANT: Classification - Typical layouts - Plant auxiliaries - Plant operation -
Pumped storage plants.
UNIT – III
____________________________________________________________________________________
((AUTONOMOUS)
NUCLEAR POWER STATION: Nuclear Energy-Fission, fusion reaction nuclear fuel- Breeding and
fertile materials - Nuclear reactor - Reactor operation. Environmental considerations.
REACTORS: Types- Pressurized water reactor, boiling water reactor, sodium-graphite reactor, fast breeder
reactor, homogeneous reactor, gas cooled reactor, radiation hazards and shielding - Radioactive waste disposal.
UNIT - IV
COMBINED OPERATIONS OF DIFFERENT POWER PLANTS:
Introduction, advantages of combined working, load division between power stations, storage type hydro-
electric plant in combination with steam plant, run-of-river plant in combination with steam plant, pump
storage plant in combination with steam or nuclear power plant, co-ordination of hydro- electric and gas
turbine stations, co-ordination of hydro-electric and nuclear power stations, co-ordination of different types of
power plants.
POWER PLANT INSTRUMENTATION AND CONTROL: Importance of measurement and
instrumentation in power plant, measurement of water purity, gas analysis, O2 and CO2 measurements,
measurement of smoke and dust, measurement of moisture in carbon dioxide circuit, nuclear measurements.
UNIT – V
POWER PLANT ECONOMICS AND ENVIRONMENTAL CONSIDERATIONS: General arrangement of
power distribution, load curves, load duration curve, definitions of connected load, maximum demand,
demand factor, average load, load factor, diversity factor - Related calculations. Costs associated with power
production. Effluents from power plants and their Impact on environment - Pollutants and pollution standards
- Methods of pollution control.
Text Books:
1 . “ A course in Power Plant Engineering,” Arora and Domkundwar, Dhanpatrai & Co, 6 ed, 2013.
2 . “ Power Plant Engineering,” P.C. Sharma/ S.K. KatariaPub, 2013.
References:
1. “Power Plant Engineering,”P.K. Nag,TMH Pub, 2 ed,2006.
2. “ Power station Engineering,” ElWakil, McHill.
3. “An Introduction to Power Plant Technology,”G.D.Rai,Khanna Pub; 3 ed, 1987.
____________________________________________________________________________________
((AUTONOMOUS)

Course Code Mechanical Vibrations (7th semester)
Prerequisite(s): Engineering Physics, Engineering mechanics 3 0 0 3
Course Objectives:
● To understand the fundamentals of different motions and vibrations.
● To study about damped and un-damped vibrations under single degree of freedom.
● To study about un-damped vibrations under two and multi degrees of freedom and also torsional
vibrations.
● To learn various vibration measuring instruments.
● To understand the concepts of modal analysis and condition monitoring.
Course Outcomes:

CO1: Describe the types of vibrations with simple harmonic motion.
CO2: Explain the un-damped vibration systems with single degree of freedom.
CO3: Discuss the damped and forced vibration systems with single degree of freedom.
CO4: Analyze the torsional vibrations of multi degree of freedom and its measurement.
CO5: Examine the modal analysis and condition monitoring of vibration systems.
Syllabus:
UNIT-I
Introduction: Definitions, Types of vibrations, Simple Harmonic Motion (S.H.M.), Work done by harmonic
force, Principle of super position applied to SHM, Beats, Fourier theorem and problems.
UNIT-II
Un-damped (Single Degree of Freedom) Free Vibrations: Derivations for spring mass systems, Methods of
Analysis, Natural frequencies of simple systems, Springs in series and parallel, Torsional and transverse
vibrations, Effect of mass of spring and Problems.
UNIT-III
Damped free vibrations (Single Degree of Freedom): Types of damping, Analysis with viscous damping -
Derivations for over, critical and under damped systems, Logarithmic decrement and Problems.
Forced Vibrations (Single Degree of Freedom): Introduction, Analysis of forced vibration with constant
harmonic excitation - magnification factor, rotating and reciprocating unbalances, excitation of support
(relative and absolute amplitudes), force and motion transmissibility, Energy dissipated due to damping and
Problems.
UNIT-IV
Vibration Measuring Instruments and Whirling of shafts: Seismic Instruments Vibrometers,
Accelerometer, Frequency measuring instruments and Problems. Whirling of shafts with and without
damping, critical speed of shafts and Problems.
____________________________________________________________________________________
((AUTONOMOUS)
Systems with two degrees of Freedom: Principle modes of vibrations, Normal mode and natural
frequencies of systems (without damping) – Simple spring mass systems, masses on tightly stretched strings,
double pendulum, torsional systems, combined rectilinear and angular systems, geared systems and Problems.
Undamped dynamic vibration absorber and Problems.
UNIT- V
Numerical Methods for multi degree freedom of systems: Introduction, Maxwell‟s reciprocal theorem,
Influence coefficients, Rayleigh‟s method, Dunkerley‟s method, Stodola method, Holzer‟s method,
Orthogonality of principal modes, method of matrix iteration and Problems
Modal Analysis and Condition Monitoring: Signal analysis, dynamic testing of machines and structures,
Experimental modal analysis, Machine condition monitoring and diagnosis.
Text Books:
1.Elements Of Vibration Analysis 2nd Edition by Meirovitch L , McGraw Hill, March 2014.
2.Mechanical Vibrations by V.P.Singh.
Reference Books:
1.Mechanical Vibrations / SS Rao / Pearson
2.Mechanical Vibrations /Rao V. Dukkipati , J Srinivas/ PHI
3.Mechanical Vibrations by Shcam Series.
4.Vibration Analysis by Nakra.
____________________________________________________________________________________
((AUTONOMOUS)

Course Code Automobile Engineering (7th semester)
Teaching Total contact hours – 64 L T P C
Prerequisite(s): Internal Combustion Engines 3 0 0 3
Course Objectives:
 To study basic and advanced automobile systems and subsystems.
 To impart knowledge on the construction and operating principle of automobile engine and auxiliary
systems.
 To Understand the Vehicle Noise, Vibrations, Harshness, Comfort and Safety Systems.
 To analyze the feasibility of alternate fuels / power source and emission control.
Course Outcomes:

CO1: Describe various functional components of an Automobile.
CO2: Explain engine auxiliary systems used in SI and CI engine.
CO3: Compare manual transmissions systems with automatic transmission systems.
CO4: Illustrate the working of steering, braking and the suspension systems.
CO5: Justify the importance of alternative fuels.
Syllabus:
UNIT-I
INTRODUCTION: Components of a four-wheeler automobile, types of automobiles, Chassis types, power
unit, power transmission, rear wheel drive, front wheel drive, Four wheel drive, Advantages and
disadvantages, types of automobile engines, cylinder liners-dry and wet, naturally aspirated engines, turbo
charging and super charging.
LUBRICATION SYSTEM: Necessity, functions of lubrication, properties of lubricants and grading,
lubrication systems and types, oil filters, oil pumps, crankcase ventilation, waste oil disposal methods.
UNIT -II
S.I. ENGINE FUEL SYSTEM: Fuel supply systems, Mechanical and electrical fuel pump, filters, simple
carburetor and its functions, modern carburetors – Zenith & Solex, Air Filters, Gasoline Direct Injection
(GDI), Multipoint Fuel Injection system (MPFI), Selection of fuel injection system.
C.I. ENGINE FUEL SYSTEM: Requirements of diesel injection systems, types of injection systems, fuel
pump- types, fuel injectors-types, Common Rail Direct Injection System (CRDI).
COOLING SYSTEM: Cooling requirements, air cooling, liquid cooling, Types, cooling thermo, and forced
circulation System, Radiators-Types, Cooling Fan, water pump, thermostat, antifreeze solutions.
UNIT- III
IGNITION SYSTEM: Function of an ignition system, battery ignition system, auto transformer, contact
breaker points, condenser and spark plug, magneto coil ignition system, electronic ignition system (CDIS &
TACIS), Ignition Timings- Ignition advance and its necessity, Centrifugal Spark Advance Mechanism,
Vacuum advance mechanism.
____________________________________________________________________________________
((AUTONOMOUS)
ELECTRICAL SYSTEM: Charging system, cut-off relay, starting system, Bendix drive, Horn, wiper, Fuel
gauge, oil pressure gauge, and Engine temperature indicator electrical circuit of automobile.
UNIT -IV
TRANSMISSION SYSTEM: Types of clutches -single plate, multi plate, and centrifugal clutches, fluid fly
wheel, gear box- types, sliding mesh, constant mesh, synchromesh, over drive,torque converter, Propeller shaft
– Hotchkiss drive, Torque tube drive, universal joint, differential, rear axles.
UNIT -V
STEERING SYSTEM: Steering geometry – camber, castor, king pin rake, combined angle toe-in, toe out,
center point steering. Steering gears – types, steering linkages, Stub axle, power steering.
SUSPENSION SYSTEM: Elements of suspension systems – rigid axle suspension system, torsion bar, shock
absorber, Independent suspension systems (Wishbone, Macpherson Strut).
BRAKING SYSTEM: Types - Mechanical, hydraulic, pneumatic & vacuum suspended servo-brake system,
brake fluids and properties.
Text Books:
1. Kirpal Singh, Automobile Engineering, Volume-I & Volume-II, Tata McGraw Hill, New Delhi,2012.
2. V.M Domkundwar, Automobile Engineering, Dhanpatrai& Co,1/e, New Delhi, 2008.
References:
1. Dr. N. K. Giri, Automobile Mechanics, 5/e, Khanna Publications, 2014
2. Heitner J, Automotive Mechanics, 2/e, CBS Publications, 2000.
3. William H Crouse, Automotive Mechanics, McGraw Hill Education (India)Private Limited, 10th edition.
____________________________________________________________________________________
((AUTONOMOUS)

Course Code Advanced Manufacturing Processes (7th Semester)

Prerequisite(s): Production Technology and Metal Cutting and Machine 3 0 0 3
Tools.
Course Objectives:
 To understand Surface Treatments methods for different applications.
 To learn about Non-Traditional Machining techniques.
 To understand working principle of Electric Discharge Machining and WEDM.
 To study the concepts of IBM, LBM, EDM and PAM.
 To learn about concepts and manufacturing of composites.
Course Outcomes:

CO1: Select suitable surface treatment technique for any given application.
CO2: Describe working principles of mechanical energy based nontraditional machining processes.
Discuss different electro chemical and discharge machining processes and also their
CO3:
applications.
CO4 Describe working principles and applications of IBM, LBM, EBM and PAM.
CO5 Explain various manufacturing techniques of composites.
Syllabus
UNIT - I
Surface Treatment: Scope, Cleaners, Methods of cleaning, Surface coating types - Ceramic and organic
methods of coating, Electro forming, Chemical vapour deposition, thermal spraying, Ion implantation,
diffusion coating, diamond coating and cladding, economics of coating.
UNIT - II
Non-Traditional Machining: Classification of unconventional machining processes and their capabilities,
Ultrasonic Machining(USM), Abrasive jet machine(AJM),Water jet machining(WJM) .
Mechanism of material removal, Process Parameters –Effects on material removal rate and surface finish,
Electro Chemical Machining – Principle of working, equipment, performance characterization,
Applications.
UNIT - III
Electric discharge machining (EDM), Wire EDM – Mechanism of material removal, Process Parameters –
Effects on material removal rate and surface finish, Electro chemical discharge grinding.
UNIT – IV
Ion Beam Machining – Principle of working, equipment, Material removal rate, Process parameters,
performance characterization, Applications.
Laser Beam Machining – Principle of working, equipment, Material removal rate, Process parameters,
Plasma Arc Machining – Principle of working, equipment, Material removal rate, Process parameters,
____________________________________________________________________________________
((AUTONOMOUS)

Electron Beam Machining - Principle of working, equipment, Material removal rate, Process
parameters, performance characterization, Applications.
UNIT - V
Manufacturing of Composites: Reinforcements and its types- Classification of composites, MMC,
Polymer matrix composites, manufacturing methods, stir casting, laser melt technique, friction stir
processing, hand layup process and other techniques.
Text Books:
1. Manufacturing Engineering and Technology, Kalpakijian, Adisson Wesley, 7th edition 2018.
2. Process and Materials of Manufacturing, R. A. Lindburg, 4th edition, PHI 2015.
References:
1. Advanced Machining Processes, V.K.Jain, Allied Publications.
2. Introduction to Manufacturing Processes, John A Schey, McGraw Hill.
3. Mechanics of Composite Materials, Second Edition (Mechanical Engineering), By Autar K.
Kaw, CRC Publisher, 2006.
____________________________________________________________________________________
((AUTONOMOUS)

Course Code Gas Dynamics and Jet Propulsions (7th Semester)
(Department Elective-IV)
Prerequisite(s): Thermodynamics, Fluid Mechanics 2 1 0 3
Course Objectives:
 To learn the fundamental concepts of Thermodynamics and fluid mechanics.
 To solve problems of fluid flow through ducts with and without heat flow including friction.
 To describe the changes in fluid flow properties across shock waves in various flow regions.
 To find performance parameters of jet propulsion engines.
 To examine Space (Rocket) propulsion engines and their performance parameters.
Course Outcomes:

CO1: Solve basic problems of thermodynamics and fluid mechanics.
CO2: Solve fluid flow problems through ducts with and without heat flow including friction.
CO3: Analyze the change in flow properties across shock waves in different flow regions.
CO4: Examine performance of jet propulsion engines.
CO5: Find the performance of Rocket engines using principles of gas dynamics.
Syllabus:
UNIT -I
BASIC CONCEPTS AND ISENTROPIC FLOWS: Energy and momentum equations of compressible
fluid flows – Stagnation states, Mach waves and Mach cone – Effect of Mach number on compressibility –
Isentropic flow through variable ducts – Nozzle and Diffusers – Use of Gas tables.
UNIT -II
FLOW THROUGH DUCTS: Flows through constant area ducts with heat transfer (Rayleigh flow) and
Friction (Fanno flow) – variation of flow properties – Use of tables and charts – Generalised gas dynamics.
UNIT -III
NORMAL AND OBLIQUE SHOCKS: Governing equations – Variation of flow parameters across the
normal and oblique shocks – Prandtl – Meyer relations – Use of table and charts – Applications.
UNIT- IV
JET PROPULSION: Theory of jet propulsion principle of operation, cycle analysis – Thrust equation –
Thrust power and propulsive efficiency, use of stagnation state performance of ram jet, turbojet, turbofan and
turbo prop engines.
UNIT -V
SPACE PROPULSION: Types of rocket engines, theory of rocket propulsion – Propellants-feeding
systems – Ignition and combustion –Performance study – Staging – Terminal and characteristic velocity –
Applications – Space flights.
____________________________________________________________________________________
((AUTONOMOUS)
Text Books:
1. Anderson, J.D., Modern Compressible flow, McGraw Hill, 2017.
2. S.M. Yahya, fundamentals of Compressible Flow, New Age International (P) Limited, New Delhi,
2003.
References:
1. P. Hill and C. Peterson, Mechanics and Thermodynamics of Propulsion, Addison – Wesley
Publishing company.
2. G.P. Sutton, Rocket Propulsion Elements, John wiley, New York.
3. V. Ganesan, Gas Turbines, Tata McGraw Hill Publishing Co, New Delhi.
4. PR.S.L. Somasundaram, Gas Dynamics and Jet Propulsions, New Age International Publishers.
5. V. Babu, Fundamentals of Gas Dynamics, ANE Books India, 2008.
6. Ethirajan Rathakrishnan, Applied Gas Dynamics, Wiley-India Edition.
____________________________________________________________________________________
((AUTONOMOUS)

GRBT-19 (Autonomous) IV B. Tech. I Sem.
(7th Semester)
Course Code Micro Electro Mechanical Systems
Prerequisite(s): Engineering Physics, Basic Electronics. 3 0 0 3
Course Objectives:
 To understand the operation of major classes of MEMS devices/systems.
 To learn the fundamentals of standard micro fabrication techniques and processes.
 To understand the unique demands, environments and applications of MEMS devices.
Course Outcomes:

CO1: Describe the working principles of micro-sensors and actuators.
CO2: Explain the application of scaling laws in the design of micro systems.
CO3: Identify the typical materials used for fabrication of micro systems.
CO4: Discuss the principles of standard micro fabrication techniques.
CO5: Analyze various micro electro mechanical systems and their construction.
Syllabus
Unit – I
INTRODUCTION: Definition of MEMS, MEMS history and development – micro machining –
lithography principles & methods, photolithography – structural and sacrificial materials, thin film
deposition – impurity doping – etching – surface micro machining – wafer bonding – LIGA.
MECHANICAL SENSORS AND ACTUATORS: Principles of sensing and actuation, beam and
cantilever, capacitive sensors, piezo-electric sensors and actuators – measurement of strain, pressure and
flow, pressure measurement by micro phone – MEMS gyroscopes, shear mode piezo actuator, gripping piezo
actuator, Inchworm technology.
Unit – II
THERMAL SENSORS AND ACTUATORS: Thermal energy basics and heat transfer processes, –
thermisters, thermo devices – thermo couple, micro machined thermo couple probe – Peltier effect heat
pumps – thermal flow sensors – micro hot plate gas sensors – MEMS thermo vessels – pyro electricity –
shape memory alloys (SMA), – U-shaped horizontal and vertical electro thermal actuator – thermally
activated MEMS relay – micro spring thermal actuator – data storage cantilever.
Unit – III
MICRO-OPTO-ELECTRO MECHANICAL SYSTEMS: Principle of MOEMS technology – properties
of light – light modulators, beam splitter, micro lens, micro mirrors – digital micro mirror device (DMD) –
light detectors – grating light valve (GLV) – optical switch, wave guide and tuning, shear stress
measurement.
____________________________________________________________________________________
((AUTONOMOUS)
Unit – IV
MAGNETIC SENSORS AND ACTUATORS: Magnetic materials for MEMS and properties – magnetic
sensing and detection – magneto resistive sensor, hall effect – magneto diodes, magneto transistor – MEMS
magnetic sensor – pressure sensor utilizing MOKE – mag MEMS actuators – bi directional micro actuator –
feedback circuit integrated magnetic actuator – large force reluctance actuator – magnetic probe based
storage device.
Unit – V
MICRO FLUIDIC SYSTEMS: Applications – considerations on micro scale fluid – fluid actuation
methods, Dielectrophoresis (DEP), Electro wetting, Electro thermal flow, thermo capillary effect, electro
osmosis flow, Opto-electro wetting (OEW) – tuning using micro fluidics – typical micro fluidic channel, –
microfluid dispenser – micro needle – molecular gate – micro pumps.
CHEMICAL AND BIO MEDICAL MICRO SYSTEMS: Sensing mechanism & principle – membrane-
transducer materials – chem.-lab-on-a-chip (CLOC) – chemoresistors, chemocapacitors, chemotransistors –
electronic nose (E-nose) – mass sensitive chemosensors – fluroscence detection – calorimetric spectroscopy.
Text Books:
1.“MEMS”, NitaigourPremchandMahalik, TMH Publishers, 1st Edition, 2008.
References:
1.“Foundation of MEMS”, Chang Liu, Prentice Hall Ltd., 2009.
2.“MEMS and Micro Systems: Design and Manufacture,” Tai-Ran Hsu, TMH Publishers, 2002.
3.“Introductory MEMS”, TM Adams, R A Layton, Springer International Publishers, 2007
4.“Fundamentals of Microfabrication”, Marc Madou, CRC press 2002.
____________________________________________________________________________________
((AUTONOMOUS)

Course Code Design for Manufacturing (7th Semester)

Prerequisite(s): Fundamentals of Production Technology and Metal cutting 3 0 0
and Machine tools 3
Course Objectives:
 To understand the complex interrelationships between design and manufacturing.
 To explore and understand basic manufacturing processes.
 To identify the various process parameters of manufacturing processes.
Course Outcomes:

CO1: Discuss the design rules for manufacturability with economical aspects.
CO2: Investigate different machining processes to attain design tolerances.
CO3: Identify the suitable casting method and process parameters for a given component.
CO4: Design of weldments and bulk forming processes.
CO5: Recommend the design parameters for sheet metal forming and processing of plastics .
Syllabus:
UNIT - I
Design Philosophy: Design for assembly and evaluation, minimum part assessment. Design for minimum
number of parts, development of modular design, minimizing part variations, design of parts to be multi-
functional, multi-use, ease of fabrication.
General design rules for manufacturability-Basic principles of designing for economical production -
Creativity in design.
UNIT –II
Machining processes: Overview of various machining processes-General design rules for machining-Surface
finish, review of relationship between attainable tolerance grades and different machining processes. Analysis
of tapers, screw threads, applying probability to tolerances.
Design for machining - Ease –Redesigning of components for machining ease with suitable examples.
General design recommendations for machined parts.
UNIT – III
Metal casting: Appraisal of various casting processes, selection of casting process- General design
considerations for casting-Casting Tolerance, solidification, simulation in casting design - Product design
rules for sand casting. Redesign of castings based on parting line considerations, redesigning cast.
UNIT –IV
Metal joining: Appraisal of various welding processes, factors in design of weldments – General design
guidelines-Pre and post treatment of welds effects of thermal stresses in weld joints-Design of brazing and
soldering joints.
Forging: Design factors for forging – Closed die forging design – Parting lines of dies – Drop forging die
design – General design recommendations. Keeler Goodman forging line diagram.
____________________________________________________________________________________
((AUTONOMOUS)
UNIT - V
Extrusion: Design guide lines extruded sections, Design factors for direct, indirect and hydraulic extrusion
Sheet metal work : Design principles for piercing, blanking, bending Die design for blanking and piercing.
Design factors of drawing process.
Plastics: Visco elastic and creep behaviour in plastics-design guidelines for plastic components-Design
considerations for injection moulding – Design guidelines for machining and joining of plastics.
Text Books:
1. “Product Design for Manufacture and Assembly”, Geoffrey Boothroyd, Peter Dewhurst, Winston A
Knight, CRC Press, 3rd Edition, 2010.
2. “Design for Manufacture: Strategies, Principles and Techniques”, John Corbett, Mike Dooner, John
Meleka, Christopher Pym, Pearson Education.
References:
1.“Design for Manufacturability Handbook”, James G. Bralla, McGraw Hill, 2nd Edition, 1998
2. “ASM Handbook – Material Selection and Design”, George E Dieter, ASM International, Vol. 20,
1997.
3.Spotts M.F., “Dimensioning and Tolerance for Quantity Production”, Prentice Hall Inc., 1983.
____________________________________________________________________________________
((AUTONOMOUS)

Automation in Manufacturing (7th Semester)
Course Code
Prerequisite(s): Production Technology 3 0 0 3
Course Objectives:
● To attain the knowledge on basic concepts of Automation.
● To learn about line balancing methods.
● To understand the concepts of material handling systems.
● To learn the concepts of adaptive control systems.
Course Outcomes:

CO1: Discuss the different fundamental concepts of automation and its tools.
CO2: Analyze the automated flow lines & line balancing methods.
Classify the automated material handling, automated storage and retrieval systems in
CO3:
industries.
CO4: Explain the working of adaptive control systems for temperature, vibration, forces etc.
CO5: Describe various automated inspection methods.
Syllabus:
UNIT – I
INTRODUCTION: Types and strategies of automation - Pneumatic and hydraulic components, circuits -
Automation in machine tools, mechanical feeding and tool changing and machine tool control.
AUTOMATED FLOW LINES: Methods of part transport, transfer mechanism, buffer storage-control
function, Design and fabrication considerations.
UNIT –II
ANALYSIS OF AUTOMATED FLOW LINES - General terminology and analysis of transfer lines
without and with buffer storage-partial automation, implementation of automated flow lines-Geneva
mechanism.
ASSEMBLY SYSTEM AND LINE BALANCING: Assembly process and systems, assembly line, line
balancing methods, ways of improving line balance, flexible assembly lines.
UNIT – III
AUTOMATED MATERIAL HANDLING AND STORAGE SYSTEMS: Types of equipment, functions-
analysis and design of material handling systems, conveyor systems, automated guided vehicle systems
Automated storage and retrieval systems-work in process storage, interfacing handling and storage with
manufacturing.
UNIT –IV
ADAPTIVE CONTROL SYSTEMS: Introduction, adaptive control with optimization, adaptive control
with constraints-application of adaptive control in machining operations.
____________________________________________________________________________________
((AUTONOMOUS)
Consideration of various parameters such as cutting force, temperatures, vibration and acoustic emission in
the adaptive controls systems.
UNIT – V
AUTOMATED INSPECTION: Fundamentals types of inspection methods, procedure, accuracy and
equipment, Coordinate Measuring Machines - Constructional detail, Programming and Operation, Machine
Vision.
Text Books:
1.Automation, Production Systems and Computer Integrated Manufacturing : M.P.GROOVER,/PE/PHI
2.Numerical Control and Computer Aided Manufacture by Pressman and Williams/john wiley/1977
References:
1.Computer Control of Manufacturing Systems by YoramCoren ,McGraw Hill Education India
2. CAD / CAM by Mikell P Groover and Emory W Zimmers/prentice hall/1 dec 1983
3.Manufacturing and Automation Technology by R. Thomas Wright/good heart –willcox pub/ june 2006
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)
____________________________________________________________________________________
((AUTONOMOUS)

(7 Semester)
Course Code CAD/CAM Lab
Prerequisite(s): Computer Aided Design and Finite Element Methods. 3 0 0 3
Course Objectives:
 To familiarize the fundamentals of CAD/CAM software.
 To provide necessary skills for numerical analysis of structural, heat transfer and fluid flow problems
using analysis package.
 To understand the NC codes for simple turning and milling operations through simulation package.
Course Outcomes:

CO1: Analyze various types of 2D and 3D trusses by static and dynamic analysis using ANSYS.
CO2: Solve the static problems involving corner bracket and cylinder components.
CO3: Examine the beams with various end conditions subjected to static load.
CO4: Analyze various thermal properties of bodies with different geometries.
CO5: Compose NC code for turning and pocket milling operations.
List of Experiments
1. Static analysis of 2D truss

2. Static analysis of 3D truss
3. Static analysis of corner bracket
4. Static analysis of an Axis-symmetric component (Cylinder).
5. Dynamic analysis of 2D truss
6. Dynamic analysis of 3D truss
7. Static Analysis of 3D structure
8. Structural Analysis of a Cantilever Beam
9. Structural Analysis of a Fixed Beam
10. Structural Analysis of a Overhanging Beam
11. Steady state heat transfer analysis on Circular rod
12. Steady state heat transfer analysis on rectangular plate with a central circular hole
13. Transient heat transfer analysis on rectangular plate with a central circular hole
14. Generation of NC code for turning operation
15. Generation of NC code for pocket milling operation
____________________________________________________________________________________
((AUTONOMOUS)

GRBT-19 (Autonomous) IV B.Tech. II Sem
Operations Research
Prerequisite(s): Probability theory 2 1 0 3
Course Objectives:
 To impart knowledge on various concepts of Operations Research.
 To understand mathematical models used in Operations Research.
 To understand the techniques constructively for making effective decisions.
Course Outcomes:
CO1: Describe the various operations research models and their applications.
Solve the various engineering and managerial problems of LPP, transportation, assignment,
CO2:
sequencing and replacement.
CO3: Apply game theory in different competitive situations.
CO4: Solve the problems related to theories of waiting line and inventory models.
Apply the principles of dynamic programming and simulation framework to solve various
CO5:
decision making situations.
Syllabus:
UNIT –I
Development, Definition, Characteristics and phases, Types of operation research models, Applications.
LINEAR PROGRAMMING PROBLEM: Linear programming problem formulation - Graphical solution -
Simplex method -Artificial variables techniques -Two–phase method - Big-M method - Special cases:
degeneracy, multiple optimal solution, infeasibility and unbounded solution, duality principle.
UNIT – II
TRANSPORTATION PROBLEMS: Formulation - Initial and optimal solutions for balanced and
unbalanced transportation problems – Degeneracy in transportation problems.
ASSIGNMENT PROBLEMS: Formulation - Optimal solution - Variants of assignment problem- Traveling
salesman problem.
SEQUENCING: Introduction, flow – Shop sequencing, n jobs through two machines, n jobs through three
machines - Job shop sequencing, two jobs through „m‟ machines.
UNIT – III
REPLACEMENT: Introduction – Replacement of items that deteriorate with time, when money value is not
counted and counted, replacement of items that fail completely, group replacement.
THEORY OF GAMES: Introduction – Mini. max (max. mini) – Criterion and optimal strategy, solution of
games with saddle points, rectangular games without saddle points, 2 x 2 games, dominance principle, m x 2
& 2 x n games , graphical method.
____________________________________________________________________________________
((AUTONOMOUS)
UNIT-IV
WAITING LINES: Introduction – Single channel, Poisson arrivals, exponential service times, with infinite
population and finite population models, multichannel, Poisson arrivals , exponential service times with
infinite population single channel Poisson arrivals.
INVENTORY: Introduction, Deterministic inventory models – Static economic order quantity models,
Dynamic economic order quantity models - Probabilistic Inventory Models – Continuous review models,
single period models and multi period models, P-System, Q-System.
UNIT – V
DYNAMIC PROGRAMMING: Introduction – Bellman‟s principle of optimality, applications of dynamic
programming, capital budgeting problem, shortest path problem, linear programming problem.
SIMULATION: Definition, types of simulation models, phases of simulation, applications of simulation,
inventory and queuing problems, advantages and disadvantages, simulation languages, problems on inventory
and queuing models.
Text Books:
1.“Operations Research,” S.D.Sharma, Kedarnath,Ramnath&Co, 5thedition, 2008.
2.“Operations Research -An Introduction” H.A. Taha., PHI, 8th edition, 2008
References:
1.“Operations Research Theory &Applications” J.K.Sharma, Macmillan, 6th edition, 2013.
2.“Operations Research,” A.M. Natarajan, P. Balasubramani, A. Tamilarasi, Pearson Education, 2nd edition,
2014
3.“Operations Research,” Methods & Problems, Maurice Saseini, ArhurYaspan& Lawrence Friedman, 1st
edition, 1959
4.“Operations Research,” R.Pannerselvam, PHI Publications, 2nd edition, 2009.
5.“Operations Research,” S Kalavathy, Vikas Publishers, 4th edition, 2013.
____________________________________________________________________________________
((AUTONOMOUS)

Course Code Computational Fluid Dynamics (8th Semester)
(Department Elective-V)
Prerequisite(s): Engineering Mathematics, Fluid Mechanics & Heat Transfer 2 1 0 3
Course Objectives:
● To familiarize the concepts of Computational Fluid Dynamics
● To learn numerical techniques for solving the partial differential equations governing the
fluid flow.
● To learn the methods to solve complicated problems by using the techniques of CFD
● To learn the concept of finite difference and finite volume methods.
Course Outcomes:

CO1: Identify different application of CFD.
CO2: Analyze governing equations of fluid dynamics using CFD.
Examine the behavior of hyperbolic, parabolic and elliptic equations by using explicit and
CO3:
implicit approaches.
CO4: Evaluate the transformed governing equations using boundary conditions.
CO5: Asses the linear 3D FVD schemes in fluid flow problems.
Syllabus:
UNIT-I
INTRODUCTION: History and Philosophy of “Computational Fluid Dynamics(CFD)” CFD as a design
Tool Applications of CFD in engineering.
UNIT -II
GOVERNING EQUATIONS OF FLUID DYNAMICS: Models of the flow The substantial derivative
Physical meaning of the divergence of velocity The continuity equation The momentum equation The
energy equation Governing equations for fluid dynamics, Navier-Stokes equations for viscous flow, Euler
equations for inviscid flow Physical boundary conditions Governing equations suited for CFD,
conservation form of the equations, shock fitting and shock capturing Time marching and space marching.
UNIT- III
MATHEMATICAL BEHAVIOR OF PARTIAL DIFFERENTIAL EQUATIONS: Classification of
quasi-linear partial differential equations General behaviour of hyperbolic, parabolic and elliptic equations.
BASIC ASPECTS OF DISCRETIZATION: Introduction to finite differences Finite difference equations
using Taylor series expansion and polynomials Explicit and implicit approaches Errors and an analysis of
stability.
UNIT –IV
GRIDS WITH APPROPRIATE TRANSFORMATION: General transformation of the equations
Metrics and Jacobians The transformed governing equations of the CFD Boundary fitted coordinate
systems Algebraic and elliptic grid generation techniques Adaptive grids.
____________________________________________________________________________________
((AUTONOMOUS)
FINITE DIFFERENCE FORMULATIONS: Parabolic partial differential equations, elliptic equations and
hyperbolic Equations.
UNIT -V
FINITE VOLUME METHOD FOR UNSTRUCTURED GRIDS: General description of the finite volume
method, Cell Centered and Nodal point schemes Two - Dimensional Heat conduction with Triangular
Elements Flux vector splitting scheme.
Text Books:
1. Anderson, J.D.(Jr), Computational Fluid Dynamics The Basics with Applications, McGraw-Hill,Inc.
,2017.
2. Hoffman, K.A., and Chiang, S.T., Computational Fluid Dynamics, Vol. I, II andIII, Engineering
Education System, Kansas, USA, 2000.
References:
1.Versteeg, H.K. and Malalasekara, W., An Introduction to Computational Fluid Dynamics: The Finite
Volume Method, 2nd Edition, Pearson Education, 2008.
2.Chung, T.J., Computational Fluid Dynamics,2nd Edition ,Cambridge University Press, 2010.
3.Richard Pletcher, John Tannehill and Dale Anderson, `Computational Fluid Mechanics and
HeatTransfer, 3rd Edition, CRC Press, 2013.
____________________________________________________________________________________
((AUTONOMOUS)

GRBT-19 (Autonomous) IV B.Tech.II Sem
Course Code Nano Technology (8th Semester)
(Department Elective-V)
Prerequisite(s): Metallurgy and Material Science 3 0 0 3
Course Objectives:
● To study the classification of nano materials.
● To understand the properties of nano materials.
● To gain the knowledge on characterization techniques like SEM, TEM and XRD.
● To impart the knowledge on the synthesis methods.
Course Outcomes:

CO1: Discuss the applications of nano materials in engineering and few other fields.
CO2: Describe the mechanical, electrical, thermal and physical properties of nano materials.
CO3: Explain the synthesis and fabrication techniques of nano particles.
CO4: Discuss the uses of characterization techniques such as spectroscopy, SEM, TEM and XRD.
CO5: Describe carbon nano technology and its various applications.
Syllabus:
UNIT-I
INTRODUCTION:
History of nano science- definition of nano meter, nano materials, nano technology-Classification of nano
materials-Crystal symmetries, crystal directions, crystal planes-Band structure-Applications in material
science, biology and medicine, surface science, energy and environment-Applications of nano structured thin
fins, applications of quantum dots.
UNIT-II
PROPERTIES OF MATERIALS: Mechanical properties, electrical properties, dielectric properties,
thermal properties, magnetic properties, opto electronic properties. Effect of size reduction on properties,
electronic structure of nano materials.
UNIT-III
SYNTHESIS AND FABRICATION: Synthesis of bulk polycrystalline samples, growth of single crystals.
Synthesis techniques for preparation of nano particle – Bottom Up Approach – sol gel synthesis, hydro
thermal growth, thin film growth, PVD and CVD. Top Down Approach – Ball milling, micro fabrication,
lithography. Requirements for realizing semiconductor nano structures, growth techniques for nano structures.
UNIT-IV
CHARACTERIZATION TECHNIQUES:X-Ray diffraction and Scherrer method, scanning electron
microscopy, transmission electron microscopy, scanning probe microscopy, atomic force microscopy, piezo
response microscopy, X-ray photo electron spectroscopy, XANES and XAFS, angle resolved photoemission
spectroscopy, diffuse reflectance spectra, photo luminescence spectra, Raman spectroscopy.
____________________________________________________________________________________
((AUTONOMOUS)
UNIT-V
CARBON NANO TECHNOLOGY: Characterization of carbon allotropes, synthesis of diamond –
nucleation of diamond, growth and morphology. Applications of nano crystalling diamond films, grapheme,
applications of carbon nano tubes.
Text Books:
1.Nano science and nano technology by M.S RamachandraRao, Shubra Singh, Wiley publishers.
2.Introduction to Nanoscience and Nanotechnology by k.k chattopadhyay/A.N Banerjee/PHI
References:
1. Introduction to Nano Technology by Charles P. Poole, Jr., Frank J.Owens, Wiley publishers.
2.Nanotechnology by Jermy J Ramsden, Elsevier publishers.
3.Nano Materials- A.K.Bandyopadhyay/ New Age International
____________________________________________________________________________________
((AUTONOMOUS)

Additive Manufacturing
Prerequisite(s): Computer Aided Design 3 0 0 3
Course Objectives:
 To understand the importance of rapid prototyping in manufacturing.
 To understand slicing methods for rapid prototyping.
 To learn liquid, powder and solid based rapid prototyping processes.
Course Outcomes:

CO1: Describe rapid prototyping and tooling systems.
CO2: Recommend the part orientation and slicing methods for rapid prototyping of given part.
CO3: Identify process parameters of liquid based rapid prototyping to improve the quality.
CO4: Illustrate powder and solid based rapid prototyping processes.
CO5: Identify process parameters for powder and solid based rapid prototyping.
Syllabus:
UNIT-I
Introduction to Rapid Prototyping/Tooling: Definition - History and development - Classification of Rapid
Prototyping/Tooling systems - Indirect Rapid Tooling - Applications of RP/T.
UNIT -II
Data processing for Rapid Prototyping: Data interfacing for Rapid Prototyping/Tooling - Part orientation
and support generation - Model slicing and contour data organization, direct and adaptive slicing.
UNIT- III
Liquid based Rapid Prototyping Systems: Principles and Processes - Stereo Lithography Apparatus
(SLA), Solid Ground Curing (SGC), Solid Creation System (SCS), E-DARTS system, Perfactory, Multi Jet
Modeling and Rapid Freeze prototyping.
UNIT -IV
Solid based Rapid Prototyping Systems: Principles and Processes –Laminated Object Manufacturing
(LOM), Fused Deposition Modeling (FDM), Paper Lamination Technology (PLT), CAM–LEM‟s CL, Offset
Fabbers system, Shape Deposition Manufacturing process (SDM) and Ultrasonic Consolidation (UC).
UNIT -V
Powder based Rapid Prototyping Systems: Principles and Processes – Selective Laser Sintering (SLS),
Three Dimensional Printing (3DP), Laser Engineering Net Shaping (LENS), Direct Shell Production Casting
(DSPC), Multiphase Jet Solidification (MJS), and Electron Beam Melting (EBM).
____________________________________________________________________________________
((AUTONOMOUS)
Text Books:
1.C K Chua, K F Leong, C S Lim, Rapid Prototyping: Principles and Applications, 2/e, World Scientific,
2003.
2.P.K. Venu Vinod and Weiyin Ma, Rapid Prototyping – Laser based and other Technologies, 1/e, Springer
Science+ Business Media, LLC, 2004.
References:
1.Rafiq I. Noorani, Rapid Prototyping: Principles and Applications, 1/e, John Wiley & Sons, 2006
2.Paul F. Jacobs, Rapid Prototyping and Manufacturing: Fundamentals of Stereolithography, 1/e, Society
of Manufacturing Engineers, 1992
3.D T Pham, S S Dimov, Rapid Manufacturing, 1/e, Springer Verlog, 2001
____________________________________________________________________________________
((AUTONOMOUS)

Production Planning and Control

Prerequisite(s): Industrial Engineering and Management and Operations 3 0 0 3
Research
Course Objectives:
 To understand the concepts of production and service systems.
 To learn about various forecasting techniques.
 To learn various inventory concepts and models.
Course Outcomes:

CO1: Explain the elements of production planning and control.
CO2: Investigate various forecasting techniques for manufacturing and service sectors.
CO3: Use the appropriate inventory model for various industrial circumstances.
CO4: Create the optimized route and schedule for the product to achieve the desired objectives.
Discuss the dispatch and control activities for production process, and also applications of
CO5:
computers in production planning and control.
Syllabus:
UNIT – I
INTRODUCTION: Definition – Objectives and functions of production planning and control – Elements of
production control – Types of production – Organization of production planning and control department –
Internal organization of department.
UNIT – II
Forecasting – Importance of forecasting – Types of forecasting, their uses – General principles of forecasting
– Forecasting techniques – Qualitative methods and quantitative methods.
UNIT – III
Inventory management – Functions of inventories – Relevant inventory costs – ABC analysis – VED analysis
– EOQ model – Inventory control systems – P-Systems and Q-Systems– Introduction to MRP I, MRP II,
ERP, LOB (Line of Balance), JIT and KANBAN system.
UNIT – IV
Routing – Definition – Routing procedure –Route sheets – Bill of material – Factors affecting routing
procedure, schedule –Definition – Difference with loading Scheduling policies – Techniques, standard
scheduling methods - Line Balancing, aggregate planning, chase planning.
UNIT – V
PRODUCTION CONTROLLING ASPECTS
____________________________________________________________________________________
((AUTONOMOUS)
Dispatching – Activities of dispatcher – Dispatching procedure, expediting – Follow up – Definition – Reason

for existence of functions – Types of follow up – Applications of computer in production planning and
control.
Text Books:
1.Elements of Production Planning and Control, Samuel Eilon, 1962.
2.Manufacturing, Planning and Control, Partik Jonsson Stig-Arne Mattsson, Tata McGraw-Hill, 2011.
References:
1.Inventory Control Theory and Practice, Martin K. Starr and David W.Miller, 1962
2.Production Planning and Control, Mukhopadhyay, PHI, 2015
3.Production Control A Quantitative Approach, John E. Biegel, 1971 (2nd edition)
4.Production Control, Moore, 1959 (2nd edition)
____________________________________________________________________________________

Megrbt 19

Uploaded by

Copyright:

Available Formats

Megrbt 19

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Megrbt 19

Uploaded by

Copyright:

Available Formats

GODAVARI INSTITUTE OF ENGINEERING & TECHNOLOGY

Godavari institute of Engg& Technology

GODAVARI INSTITUTE OF ENGINEERING & TECHNOLOGY

GIET Campus, Chaitanya Knowledge city,NH-16,Rajahmundry,East Godavari, A.P.

GRBT- 19 COURSE STRUCTURE

S. Course Course Periods per Week

1 19198101 BSC Mathematics-I 3 0 0 3 30 70 100

2 19198102 HSMC Communicative English I 3 0 0 3 30 70 100

3 19198103 BSC Engineering Chemistry 3 0 0 3 30 70 100

Basic Electrical &

6 19198176 ESC Engineering Graphics 1 0 3 2.5 30 70 100

Total 15 0 12 19 300 500 800

BSC = 7.5 ESC=7 HSMC=4.5 MC=0

S. Course Periods per Week

1 19198201 BSC Mathematics-II 3 0 0 3 30 70 100

5 19198205 MC Environmental Studies 2 0 0 0 30* _ _

Total 15 2 12 21 350 550 900

BCS=7.5 ESC=9 HSMC=4.5 MC=0

B. Tech. III Semester

S. Course Periods per Week

1 19139301 BSC Mathematics-III 3 0 0 3 30 70 100

3 19130303 PCC Mechanics of Solids 2 1 0 3 30 70 100

4 19130304 PCC Kinematics of Machinery 2 1 0 3 30 70 100

5 19130305 PCC Thermodynamics 2 1 0 3 30 70 100

Fluid Mechanics &

Total 17 3 6 21 280 520 800

BCS = 3 ESC =3 PCC = 15

S. Course Periods per Week

S. Course Periods per Week

S. Course Periods per Week

B. Tech. VII Semester

S. Course Periods per Week

B. Tech. VIII Semester

S. Periods per Week

Total 6 0 18 15 140 260 400

NOTE:- L - LECTURE T- THEORY P – PRACTICAL C – CREDITS

COURSE COMPONENT DISTRIBUTION

Sl. Categ GRBT APSCH AICTE

Prerequisite(s): Kinematics of Machinery 3 0 0 3

On Completion of the course, the students will be able to-

( 1: Slight [Low]; 2: Moderate[Medium]; 3: Substantial[High], '-' : No Correlation)

Regulation Godavari Institute of Engineering & Technology

Teaching Total contact hours-64 L T P C

Regulation Godavari Institute of Engineering & Technology

Teaching Total contact hours-62 L T P C

Prerequisite(s): Fundamentals of Engineering Thermodynamics 2 1 0 3

On Completion of the course, the students will be able to-

Regulation Godavari Institute of Engineering & Technology

Teaching Total contact hours–60 L T P C

Prerequisite(s): Material Science, Strength of Materials 3 0 0 3

On Completion of the course, the students will be able to-

MILLING MACHINES: Working principle – Specifications – Classification of milling Machines –

Regulation Godavari Institute of Engineering & Technology

Prerequisite(s): Internal Combustion Engines 3 0 0 3

On Completion of the course, the students will be able to-

Regulation Godavari Institute of Engineering & Technology

Prerequisite(s): Fluid Mechanics 3 0 0 3

On Completion of the course, the students will be able to-

Regulation Godavari Institute of Engineering & Technology