SIPROTEC 5 - Configuration

________________________________________________________________________________________________

Device: 7SK82 Motor protection

Product code

Short: P1H132886
Long: 7SK82DAAAAA00AAAA0AC041112111BACA000000AB0HB1BD4JB0

Technical Data:

Firmware: Current version

Binary inputs: 11
Binary outputs: 9 Relays (9 Standard, 0 Fast, 0 High-Speed, 0 Power)
Current transformers: 4 for protection
Voltage transformers: 4 standard
Measuring-transducer inputs: 0 (20 mA or 10 V, fast)
4 (20 mA, standard)
0 (DC 300 V)
0 (20 mA, fast)
12 (temperature)
Housing width: 1/3 x 19''
Housing type: Flush mounting
Modules in 19" row 1: IO102, PS101, IO111
LEDs/Push-buttons: 16 LEDs
Operation Panel: Integrated
Key switch: Without
Display type: Small display
Front Design: Standard
Power Supply: DC 110 V-250 V, AC 100 V-230 V
________________________________________________________________________________________________
1/7
SIPROTEC 5 - Configuration
________________________________________________________________________________________________

Communication/Plug-in modules:

Communications encryption: Normal

Integrated Ethernet port J: for DIGSI 5
Plug-in module position E: ETH-BA-2EL: 2x electric Ethernet 100 Mbit/s, RJ45
Communication Protocols: applicable for DIGSI 5, IEC 61850-8-1
MMS and
GOOSE, IEC 60870-5-104, DNP3 TCP, Modbus TCP,
Synchrophasor (IEEE
C37.118 - IP), Profinet IO, SUP, DHCP, SNTP, SNMP, etc.
Redundancy protocols: Line Mode, RSTP, HSR, PRP

Plug-in module position F: ANAI-CA-4EL: 4 Analog inputs 20 mA, screw terminals

Functions:

Function points class: Base + 20 function points

Note on function-points class

The function-points class results from the sum of the function points of the selected functions. You can
apply these functions according to the selected function-points class. The device also allows each other
selection of functions if the sum of the required function points is within the selected function-points
class.

From Version V9.3 on the function-points class "1400+" is withdrawn. With this class function-points
exceeding the limit of 1400 were free of charge. The maximum function-points class is now 1400. If a
function-points budget of more than 1400 points is required for a device the application
Function-Point-Manager need to be applied. All function points are liable to cost.

In the engineering phase DIGSI 5 checks that the selected configuration is suitable (capable of running
in the device) before loading it to the device.

Miscellaneous:

Warranty: 5 years
Special Approvals: Without
Firmware: Current version

________________________________________________________________________________________________
2/7
SIPROTEC 5 - Configuration
________________________________________________________________________________________________

7SK82 Motor Protection - Overview Function points calculation

(P1H132886)

Functions Free of Charge

ANSI Function Abbr. Included

Protection functions for 3-pole tripping 3-pole

14 Locked rotor I> + n<

37 Undercurrent I<

38 Temperature supervision θ>

46 Negative-sequence overcurrent protection I2>

46 Unbalanced-load protection (thermal) I2² t>

48 Starting-time supervision for motors I²start

49 Thermal overload protection θ, I²t

49 Thermal overload protection, user-defined characteristic θ, I²t

49R Thermal overload rotor protection (motor) θR

Instantaneous tripping at switch onto fault SOTF

50HS Instantaneous high-current tripping I>>>

50/51 TD Overcurrent protection with positive-sequence current I1 I1> 20 X

(from V7.9)

50N/ 51N Overcurrent protection, ground IN>

TD
50N/ 51N Overcurrent protection, 1-phase IN>
TD
50Ns/ 51Ns Sensitive ground-current detection for systems with INs>
resonant or isolated neutral systems incl. a) 3I0>, b)
admittance Y0>, c) 3I0-harm> (from V7.8)
50L Load-jam protection I>L

66 Restart inhibit for motors I²t

74TC Trip-circuit supervision TCS

74CC Closed-circuit supervision (from V7.9) CCS

86 Lockout

________________________________________________________________________________________________
3/7
SIPROTEC 5 - Configuration
________________________________________________________________________________________________

AFD Arc-protection (only with plug-in module ARC-CD-3FO) 5X

Measured values - standard

Switching statistic counters

PQ-Basic measured values: THD (Total Harmonic

Distortion) and harmonics (from V8.01) THD voltage
aggregation values (from V8.40)
CFC (Standard, control)

Switching sequences function

Inrush current detection

External trip initiation

Control

Protection interface, serial

Monitoring and supervision

Fault recording of analog and binary signals

Frequency-tracking groups (from V7.8) 6X

Temperature acquisition via communication protocol

Functions with Costs

ANSI Function Abbr. Included Quantity Value Points

24 Overexcitation protection V/f 0 25 0
25 Synchrocheck, synchronization Sync 0 50 0
function
27 Undervoltage protection: V< 0 5 0
"3-phase" or
"positive-sequence system V1"
or "universal Vx"
27R, 59R Rate-of-voltage-change dV/dt 0 5 0
protection (from V8.30)
Undervoltage-controlled Q>/V< 0 15 0
reactive power protection
32, 37 Power protection P<>, Q<> 1 10 10
active/reactive power
32R Reverse-power protection - P< 1 5 5
________________________________________________________________________________________________
4/7
SIPROTEC 5 - Configuration
________________________________________________________________________________________________

46 Negative-sequence I2>, ∠(V2,I2) 0 10 0

overcurrent protection with
direction
47 Overvoltage protection, V2> 0 5 0
negative-sequence system
47 Overvoltage protection: V2>; V2/V1> 0 5 0
"negative-sequence V2" or
"negativ-sequence
V2/positiv-sequence V1"
50/51 Overcurrent protection, phases I> 2X 2 30 0
TD

Ground-fault detection via IN-pulse 0 15 0

pulse pattern detection; Note:
this stage additionally requires
the function 50Ns/51Ns or
67Ns "Sensitive ground-fault
detection for systems with
resonant or isolated neutral"
Intermittent ground-fault Iie> 0 20 0
protection
50BF Circuit-breaker failure CBFP 0 5 0
protection, 3-pole
50RS Circuit-breaker restrike CBRS 0 20 0
protection
51V Overcurrent protection, t=f(I,V) 0 10 0
voltage dependent
59, 59N Overvoltage protection: V> 0 5 0
"3-phase" or "zero-sequence
system V0" or "universal Vx"
60 Voltage-comparison ΔU> 0 5 0
supervision
67 Directional overcurrent I>, ∠(V,I) 0 15 0
protection, phases
67N Directional overcurrent IN>, ∠(V,I) 0 15 0
protection, ground
67Ns Dir. sensitive ground-fault 0 30 0
detection for systems with
resonant or isolated neutral
incl. a) 3I0>, b) V0>, c)
Cos-/SinPhi, d) Transient
ground-fault fct., e) Phi(V,I), f)
admittance
Directional stage with a ∠(V0h,I0h) 0 10 0
harmonic; Note: this stage
additionally requires the
function "67Ns Dir. sensitive
ground-fault detection for
systems with resonant or
isolated neutral"

________________________________________________________________________________________________
5/7
SIPROTEC 5 - Configuration
________________________________________________________________________________________________

Directional intermittent Iie dir> 0 20 0

ground-fault protection
79 Automatic reclosing, 3-pole AR 0 35 0
81 Frequency protection: "f>" or f<>; df/dt<> 0 5 0
"f<" or "df/dt"
81U Underfrequency load-shedding f<(UFLS) 0 15 0
Vector-jump protection Δφ> 0 20 0
87N Restricted ground-fault ΔIN 0 15 0
protection
90V Automatic voltage controller 0 150 0
for two-winding transformer
90V Automatic voltage controller 0 180 0
for two-winding transformer
with parallel operation
Number of two-winding 2 5 0
transformers with parallel
operation (Note: only together 2X
with the function "Automatic
voltage controller for
two-winding transformer with
parallel operation")
FL Fault locator, single-sided FL-one 0 25 0
PMU Synchrophasor measurement PMU 0 40 0
Measured values - extended: 0 3 0
Min, Max, Avg
PQ-Basic measured values: 0 20 0
Voltage unbalance (from
V8.40)
PQ-Basic measured values: 0 30 0
Voltage variations - voltage
dips, swells and interruptions
(from V8.40)
PQ-Basic measured values: 0 10 0
TDD - Total Demand Distortion
(from V8.40)
CFC arithmetic 0 40 0
Circuit-breaker monitoring ΣIx, I²t, 2P, tO, 0 10 0
(from V9.20) tC, pole
scatter,
discepancy
Disconnector monitoring (from tO, tC 0 5 0
V9.50)
Circuit-breaker 4X 4 3 0

________________________________________________________________________________________________
6/7
SIPROTEC 5 - Configuration
________________________________________________________________________________________________

Disconnector/Grounding 4X 4 3 0
switch

Multiplexing of protection 0 50 0
interface
SSR Slow-scan recorder (Mod.: SSR 1X 1 40 0
from V8.80, Non-Mod.: from
V9.40)
CR Continuous recorder (Mod.: CR 1X 1 25 0
from V9.20, Non-Mod.: from
V9.40)
TR Trend recorder (Mod.: from TR 1X 1 25 0
V9.30, Non-Mod.: from V9.40)

Cyber Security: Role-Based 0 25 0

Access Control (from V7.8)
Cyber Security: IEEE 802.1x 0 10 0
based network authentication
(from V8.3)
Total: 15

________________________________________________________________________________________________
7/7