Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Rigidez Torcional Chassi XXV COBEM Final

Download as pdf or txt
Download as pdf or txt
You are on page 1of 9

See discussions, stats, and author profiles for this publication at: https://www.researchgate.

net/publication/337749270

CHASSIS TORSIONAL RIGIDITY: VALIDATION OF FEA DATA BY


EXPERIMENTAL TEST

Conference Paper · January 2019


DOI: 10.26678/ABCM.COBEM2019.COB2019-2174

CITATIONS READS

0 208

5 authors, including:

Luís Fernando Marzola da Cunha Matheus Lisboa Cardoch Valdes


University of Brasília University of Brasília
3 PUBLICATIONS 0 CITATIONS 1 PUBLICATION 0 CITATIONS

SEE PROFILE SEE PROFILE

Danilo dos Santos Oliveira


University of Brasília
35 PUBLICATIONS 16 CITATIONS

SEE PROFILE

Some of the authors of this publication are also working on these related projects:

Desenvolvimento de um protótipo final da solução de ablação para tratamento de câncer de fígado nacional que gere inovação na área View project

All content following this page was uploaded by Luís Fernando Marzola da Cunha on 02 November 2020.

The user has requested enhancement of the downloaded file.


CHASSIS TORSIONAL RIGIDITY: VALIDATION OF FEA DATA BY
EXPERIMENTAL TEST
Luís Fernando Marzola da Cunha
Matheus Lisboa Cardoch Valdes
Rhander Viana
Danilo dos Santos Oliveira
Faculty of Gama - University of Brasília
fernandoluismc@gmail.com, matheuscardoch@gmail.com,rhanderviana@gmail.com,unbdanilo@gmail.com
Luiz Eduardo Rodrigues Vieira
Universidade Federal de Uberlândia, Campus Santa Mônica, CEP: 38400-097, Uberlândia-MG
luizeduardoodrigues@gmail.com

Abstract. This paper exposes how the torsional stiffness of a formula SAE student’s (FSAE) frame can be evaluated by
bench testing and comparing the results from two different models of testing. The team FGR UnB provides his chassis
for the test with two different types of clamping to observe its consequences. The final results did not allow to validate
the computational model, however, permits to observe important factors along the bench testing and corroborate some
patterns of the results. These modeling setups were analyzed and tested on the same tubular chassis: the first aims to
be as similar as possible to the real suspension anchor points and the second is simplest than first and is analogous to
models used since 1990’s decade, to obtain a reasonable chassis’ stiffness results that can be useful to some situations.

Keywords: Torsional Rigidity, Formula SAE Chassis, Model

1. INTRODUCTION

The Formula SAE competitions challenge teams of university’s undergraduate and graduate students to conceive,
design, fabricate, develop and compete with small formula style vehicles (FSAE, 2018). In this context, the University of
Brasilia (UnB) has the electrical car team FGR that develops its own project. The frame of an automobile has the purpose
of connecting the front and rear suspensions while providing attachments points for the different systems of the car (III
and Salinas, 1996).
The frame’s torsional rigidity can be described, in an easy way to understand, as the difficulty imposed by the config-
uration and material rigidity of the frame to the torsional movement caused by cornering and it’s effects to the chassis,
and it’s simplified mechanical perspective can be seen at Fig.(1). Another perspective to understand the torsional rigidity
N.m
may be the physical analysis, by its measurement unit that is degree .Along well developed and integrated teams’ projects,
others attached components are used to increase the torsional rigidity, as the engine for example (William Milliken and
Douglas Milliken, 1995).
The magnitude of a frame’s stiffness is a characteristic related to the vehicle and circuit purpose. As the suspension’s
project team usually assume the frame as a stiffness body, consequently the frame’s project team must set as target the
highest rigidity possible (Tanawat Limwathanagura, 2012). However, like almost everything in engineering, it can not be
stated that this is a desired characteristic for any and all situations, for a formula student structure team usually it is a good
setting goal in the majority.
Since the torsional rigidity has an influence on the first of the principal objectives setting by William Milliken and
Douglas Milliken (1995), that is the maintenance of cornering balance (neutral steer) under maximum lateral conditions,
this feature deserves due attention along with designing, constructing and validating the vehicle.
The results can be very different depending on the method used to determine the torsional rigidity. The comparison
between a traditional model and an alternative and simpler model is made with aid of an experimental apparatus built for
this purpose.
The physical integrity of the chassis can be preserved during the tests. Usually, the loads applied on these torsional
rigidity tests require slightly. However, it is important to verify during the simulations if the stresses and strain continue
in the elastic regime to avoid compromise its integrity.
Finally, it is important also to the bench tests and its complements to be as rigidity as possible (it has to be verified
F. Luís, C. Matheus, V. Rhander, O. Danilo, V. Luiz
Chassis’ Torsional Rigidity: Validation of FEA Data by Experimental Test

Figure 1: Mechanical Principle


Scheme of Torsion Loads - Adams Figure 2: Simple Test Adams
(1993) (1993)

during its project), due to the possibility of its deformation during the test and consequently the appearance of residuals
in results.

2. METHODOLOGY

Once there is the chassis projected and constructed, is important to verify the math models and determine exactly what
characteristics the structure has achieve in terms of torsional rigidity. The torsional rigidity can be calculated by the ratio
between an applied torque and its resultant angular deflection of known points at the frame (Riley and George (2002a)).

Figure 3: Front Suspension Test Figure 4: Front Suspension Test


Loads 0 Loads 0

The equations (1), (2) and (3) allows to calculate the torsional rigidity KT through two symmetrical points of the
chassis. Usually as result is presented the torsional rigidity along an upper and lower guidelines along the frame. It is
important to notice that each singular point of chassis has it own torsional rigidity, even if the most usual is to present the
result from average of left and right deflections.

T
KT = (1)
θ
∆ + ∆ 
A B
θ = tan−1 (2)
L1
P (L1 + 2L2 ) FL
KT =  =   (3)
tan−1 ∆AL+∆ B
tan−1 ∆y1 +∆y2
1 2L

The calculation of torsional rigidity is the same for any kind of bench test setup, since all that is necessary is the
vertical deflection and distance of this point to the axis of reference to the applied torque, which coincide with frame’s
central plane (other representation can be found at Barari et al. (2011)).
In order to facilitate the points of interest’s identification, the Fig.(5) present the adopted nomenclature.
0 Figures 3 and 4 - Riley and George (2002a)
25th ABCM International Congress of Mechanical Engineering (COBEM 2019)
October 20-25, 2019, Uberlândia, MG, Brazil

Figure 5: Identification of points/nodes - Author

The model should achieve the reality of cornering. Thus proposed models cover the maximum real transfer load from
suspension to the frame at the first model and the most used method among most types of frames at the second model
of this article, which has the primary disadvantage of create load paths that do not represent the same manner as on the
tracker (Riley and George (2002a)).
The models should follow some rules or advises that are applied also to the basic concept of designing a space
frames, it is desirable to have a triangulated frame to increase rigidity [Adams (1993)] and also the loads be applied
properly on nodes. Therefore, if these two statements are respected, the frame’s tubes will be subjected just by traction
and compression while avoiding it to working on bending, because of that it is important to remember this also while
modelling the tests.
It was decided to evaluate two methodologies through, the first one is based on the traditional torsional stiffness test
where the rear suspension points are clamped and a torque is applied on the front suspensions points (Riley and George,
2002b), the second model is simplest than model 1 and is currently used since 90’s decade as shown in Fig(2). The
model two of this paper consists of clamping the bottom two symmetrical mounting points of the chassis, at front and rear
suspension, instead of the all suspension mounting points.
During the experiments on bench test, the frame is mounted as the respective boundary conditions adopted and a dial
indicator (Mitutoyo 2046s) is used to check the displacement of each point. The methodology should respect and notice
some principles related to scientific methods as accuracy, resolution, hysteresis, precision, calibration, gain, offset and
noise to avoid bad data and consequently erroneous analysing accordingly William Milliken and Douglas Milliken (1995).
For all points were made 5 measurements, and the experimental process error was calculated with T Student’s bicaudal
distribution (2,571) with 95% of confidence level.

2.1 Experimental test

The torsion rig in Fig. (6) uses "I" section steel beams, it is composed by two basis, the rear basis beams are
connected through welding and the front basis has a pivot in the center that allows the application of torque. The load is
applied using weights. To attach the frame to the rig, a connection element, in red Fig. (7), was designed with the same
geometry of the A-arms suspension. The measurement of deflection is made with dial indicators. There are several types
of torsion rigs and measurement styles for the same purpose, they diverge in terms of results, construction demand time
and costs for the test, for instance, the use of 3D motion capture techniques (Featherston et al., 2005).
F. Luís, C. Matheus, V. Rhander, O. Danilo, V. Luiz
Chassis’ Torsional Rigidity: Validation of FEA Data by Experimental Test

Figure 6: Model 1:Connection be- Figure 7: Assembly: Torsion rig


tween the chassis and the apparatus and Chassis - Model 2

2.1.1 Model 1

Having considered the importance of mounting the points to receive the forces on triangle’s nodes, it is also rea-
sonable to look at the model and perceive that applying the forces at suspension’s points is the best way to simulate the
reality of cornering, which is the event that provides the torsion on chassis.

Figure 8: Model 1 View - Total Deformation Z


- Author Figure 9: Model 1 View - Experimental

The model 1 consists on fix the anchor points SRR, IRR, SRF, IRF, SLR, ILR, SLF, ILF from suspension’s rear and
the equivalent points from suspension’s front using a specific connection element (Fig. 7) to each part of suspension.

2.1.2 Model 2

In order to have a simplest experimentation and aiming reasonable results, depending on the situation, the model 2
represented at Figs. (7) and (11) may be the best option.

Figure 10: Model 1 View - Total Deformation Z


- Author Figure 11: Model 2 View - Experimental

The model 2 consist on fix the points IRR and ILR from suspension’s rear and IRF, ILF from suspension’s front by
clamps as can be observed at Fig. (11).
25th ABCM International Congress of Mechanical Engineering (COBEM 2019)
October 20-25, 2019, Uberlândia, MG, Brazil

2.2 Numerical model

In order to mesh the domain, ANSYS 18 Workbench was used, the properties of the mesh and material are found in
the Tab. 1. The simulation was performed with two different elements. The first one is the BEAM 189, a 3-node beam
element that is based on the Timoshenko beam theory , the second element is the SOLID 187, a 3D 10-node element that
is able to represent irregular geometries (Tadeusz Storlaski, 2018), such as the tubes’ notch.

Table 1: Mesh and material data


Type of element SOLID 187 BEAM 189
Number of nodes 1496606 259347
Number of elements 592385 87326
Material density 7850 kg/m3 same
Young’s Modulus 2E11 Pa same
Poisson’s Ration 0.3 same
Behaviour Isotropic same

The purpose of present two methodologies in this paper is to qualifying and quantifying the results achieved from
a methodology considered completed and other simpler, the boundary conditions are represented at Fig. (12) and (13)
respectively.

Figure 12: Model 1 View - Isometric - Figure 13: Model 2 View - Isometric -
Author Author

The applied forces have the magnitude of 760 N and their distance from the chassis’ center line is 500 mm. The spread
distance is measured from the point of interest to the symmetrical plane which coincides chassis’ centre and the torque
results from the twisted force and its distance from the same plane.
To model 1 were applied two different boundary condition’s setup, the first allows the displacement long Z and rotation
along X of rear suspension’s points SLF, SLR, ILF, ILR, SRF, SRR, IRF and IRR, and the second boundary condition
setup allow only displacement along Z. For both computational setup were applied remote force at frontal suspension’s
points SLF, SLR, ILF, ILR, SRF, SRR, IRF, and IRR, at 0.5m distant from center.
The boundary conditions applied at computational simulation to model 2 were fixed support at the mounting points of
rear suspension IRR and ILR and a remote force acting on front suspension’s points IRF and ILF, at 0.5m distant from
center.

3. RESULTS AND DISCUSSIONS

The experimental results from bench testing are presented at Tab.(2) and allow to observe that in general the model 2
has less error than 1, and some points as ILF, ILR SIS2 tend to have a bigger error. The error associated at ILR is null
because it has no displacement, since is fixed at the bench test and has no displacement.
The experimental error can arise because of some factors, accordingly to the methodology executed, they are :
• Slipping of the dial indicator on its pickup point
• Bending in the rear connecting elements
• slightly angled between vertical direction and real setup of the dial indicator
F. Luís, C. Matheus, V. Rhander, O. Danilo, V. Luiz
Chassis’ Torsional Rigidity: Validation of FEA Data by Experimental Test

Table 2: Experimental Errors (T-Student - Bicaudal - 95% Confidence Level)


Experimental Error (%)
Frontal Side Impact Rear
SLF SLR ILF ILR SIS1 SIS2 SII1 SII2 SLF SLR ILR ILR
Model 1 6,36 1,52 9,88 3,65 4,68 3,60 7,57 3,37 6,54 6,99 5,03 10,38
Model 2 3,59 8,31 13,32 7,78 1,51 17,81 1,92 1,66 1,89 7,92 4,67 0

The Figure (14) present the displacement of each point along the chassis, beginning from point 1 on left to point 6 that
represents respectively for upper line the points SLF (Frontal), SRR(Frontal), SIS1 (Side Impact), SIS2 (Side Impact),
SLF (Rear), SRR(Rear) and for bottom line ILF (Frontal), IRR(Frontal), SII1 (Side Impact), SII2 (Side Impact), ILF
(Rear), IRR(Rear). The dotted line represents the Model 1 results and the continued line the results of Model 2.

Figure 14: Displacement Models 1 and 2

As expected, model 1 has definitely bigger torsional rigidity, since the displacement along chassis due to torsional
loads are smaller. The model 1 does not subject the frame to loads as the real track does with the integration of suspension
on all chassis’ mounting points (Riley and George (2002a)). For this reason, this work aimed to compare the results from
both models.
Therefore, the Figure (15) present the comparative between experimental results of model 2 and its computational
results. The key factor to corroborate the computational data with the experimental is to reproduce the correct boundary
conditions. Therefore some different kind of boundary conditions were tested, since fixed support at rear mounting points
until more specifics that are shown at Fig.(15).
25th ABCM International Congress of Mechanical Engineering (COBEM 2019)
October 20-25, 2019, Uberlândia, MG, Brazil

The Continued line represents the computational results from model 2 with suspension’s rear points SLF, SLR, ILF,
ILR, SRF, SRR, IRF, IRR only with displacement along Z free.
The dotted line with dot at the points of interest represents the computational results from model 2 with suspension’s
rear points SLF, SLR, ILF, ILR, SRF, SRR, IRF, IRR only with displacement along Z free and rotation around X free.
The experimental results are shown whit simple dotted line, and for all three the red represent upper chassis’s guideline
and blue, bottom.

Figure 15: Displacement Models 1 and 2

Thus, from Figure (15) is possible to observe that the rotation around X increases the divergence between computa-
tional and experimental data, actually is very clear how it occurs right on the points 5 and 6 that are coincident to the rear
suspension mounting points.
The Table (3) present the comparison for model 1 between experimental and computational results. The magnitude of
found errors does not allow to validate the computational data, however is possible to observe that the torsional rigidity
path along all the frame is similar for both, experimental and computational (Z Free) results.

Nm
Table 3: Torsional Rigidity degree
- Experimental x Computational Data
Guideline 1 2 3 4 5 6
Upper 1414,23 1183,83 2155,18 1828,72 1824,25 3177,7
Experimental
Bottom 1631 959 2049 1971 1896 2807
Coputational Upper 2706,23 (39,73%) 2550,84 (62,4%) 3000,23 (34,3%) 3236,51 (39,10%) 2734,73 (30,66%) 2311,38 (21,44%)
Z free Bottom 1842,61 (30,29%) 1899,67 (60,46%) 2797,8164 (29,81%) 3093,99 (69,18%) 2380,47 (30,48%) 1536,67 (51,64%)
F. Luís, C. Matheus, V. Rhander, O. Danilo, V. Luiz
Chassis’ Torsional Rigidity: Validation of FEA Data by Experimental Test

4. CONCLUSION

The comparison of results did not achieve deviation parameters that allows to validate the boundary conditions applied
to the computational simulation’s results. Differences between 21,44% and 69,18% from torsional rigidity calculated
experimentally to computational can be observed at Tab. (3). This emphasises the importance of validating the simulation
methods, which means that with only a simulation, without a previous model validation, is not enough to give information
about the real physical behaviour.
However, this work allows to make the comparison between model 1 and 2, and confirm that the model 2 can be used
for estimate a previous torsional rigidity, without any problems related to security since it underestimate the torsional
rigidity of the chassis working on all complete mounting points.
Related to the experiments, it is possible to conclude that is very important to give due attention to the positioning
of dial indicator and be careful to avoid sliding. The properly measurements acquisition to calculate the error will give
results with more credibility, so it should not be ignored.
Finally, in respect to the validation and corroboration of experimental and FEA data could not be achieved, however it
is possible to observe that the boundary conditions that is more close was the points SLF, SLR, ILF, ILR, SRF, SRR, IRF,
and IRR from rear suspension allowed just to displace along Z.

5. REFERENCES

Adams, H., 1993. Chassis engineering : chassis design building tuning for high performance handling. Berkley Pub-
lishing Group, 375 Hudson Street New York, New York 10014, first edition edition.
Barari, A., Tebby, S. and Esmailzadeh, E., 2011. “Methods to determine torsion stiffness in an automotive chassis”.
Computer-Aided Design and Applications, Vol. 1, pp. 67–75. doi:10.3722/cadaps.2011.PACE.67-75.
Featherston, C., Holford, K., Holt, C., Manning, D. and Claisse, A., 2005. Measuring the Torsional Stiffness of a Space
Frame Chassis Using 3D Motion Capture Techniques, Vol. 3-4, pp. 423–428. doi:10.4028/www.scientific.net/AMM.3-
4.423.
FSAE, 2018. “Rules 2019”.
III, E.F.G. and Salinas, A.R., 1996. “Introduction to formula sae suspension and frame design”. SAE.
Riley, W.B. and George, A.R., 2002a. “Design, analysis and testing of a formula sae car chassis”. In Proceedings of the
2002 SAE Motorsports Engineering Conference and Exhibition (P-382). Indianapolis, Indiana.
Riley, W.B. and George, A.R., 2002b. “Design, analysis and testing of a formula sae car chassis”. SAE TECHNICAL
PAPER SERIES, p. 382.
Tadeusz Storlaski, Yuji Nakasone, S.Y., 2018. Engineering Analysis with ANSYS Software. Elsevier, The Boulevard,
Langford Lane, Kidlington, Oxford OX5 1GB, United Kingdom, second edition edition.
Tanawat Limwathanagura, Chartree Sithananun, T.L.T.S., 2012. “The frame analysis and testing for student formula”.
International Journal of Mechanical and Mechatronics Engineering, Vol. 6, No. 5, pp. 998–1002.
William Milliken, W. and Douglas Milliken, D., 1995. Race Car Vehicle Dynamics. Society of Automotive Engineers,
Inc, 400 CommonwealthDrive Warrendale, PA 15096-0001 USA, first edition edition.

View publication stats

You might also like